/**
  ******************************************************************************
  * @file    misc.c
  * @author  MCD Application Team
  * @version V1.0.0
  * @date    30-September-2011
  * @brief   This file provides all the miscellaneous firmware functions (add-on
  *          to CMSIS functions).
  *          
  *  @verbatim   
  *                               
  *          ===================================================================      
  *                        How to configure Interrupts using driver 
  *          ===================================================================      
  * 
  *            This section provide functions allowing to configure the NVIC interrupts (IRQ).
  *            The Cortex-M4 exceptions are managed by CMSIS functions.
  *
  *            1. Configure the NVIC Priority Grouping using NVIC_PriorityGroupConfig()
  *                function according to the following table.
 
  *  The table below gives the allowed values of the pre-emption priority and subpriority according
  *  to the Priority Grouping configuration performed by NVIC_PriorityGroupConfig function
  *    ==========================================================================================================================
  *      NVIC_PriorityGroup   | NVIC_IRQChannelPreemptionPriority | NVIC_IRQChannelSubPriority  |       Description
  *    ==========================================================================================================================
  *     NVIC_PriorityGroup_0  |                0                  |            0-15             | 0 bits for pre-emption priority
  *                           |                                   |                             | 4 bits for subpriority
  *    --------------------------------------------------------------------------------------------------------------------------
  *     NVIC_PriorityGroup_1  |                0-1                |            0-7              | 1 bits for pre-emption priority
  *                           |                                   |                             | 3 bits for subpriority
  *    --------------------------------------------------------------------------------------------------------------------------    
  *     NVIC_PriorityGroup_2  |                0-3                |            0-3              | 2 bits for pre-emption priority
  *                           |                                   |                             | 2 bits for subpriority
  *    --------------------------------------------------------------------------------------------------------------------------    
  *     NVIC_PriorityGroup_3  |                0-7                |            0-1              | 3 bits for pre-emption priority
  *                           |                                   |                             | 1 bits for subpriority
  *    --------------------------------------------------------------------------------------------------------------------------    
  *     NVIC_PriorityGroup_4  |                0-15               |            0                | 4 bits for pre-emption priority
  *                           |                                   |                             | 0 bits for subpriority                       
  *    ==========================================================================================================================     
  *
  *            2. Enable and Configure the priority of the selected IRQ Channels using NVIC_Init()  
  *
  * @note  When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. 
  *        The pending IRQ priority will be managed only by the subpriority.
  *
  * @note  IRQ priority order (sorted by highest to lowest priority):
  *         - Lowest pre-emption priority
  *         - Lowest subpriority
  *         - Lowest hardware priority (IRQ number)
  *
  *  @endverbatim
  *
  ******************************************************************************
  * @attention
  *
  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
  *
  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "misc.h"

/** @addtogroup STM32F4xx_StdPeriph_Driver
  * @{
  */

/** @defgroup MISC 
  * @brief MISC driver modules
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
#define AIRCR_VECTKEY_MASK    ((uint32_t)0x05FA0000)

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/** @defgroup MISC_Private_Functions
  * @{
  */

/**
  * @brief  Configures the priority grouping: pre-emption priority and subpriority.
  * @param  NVIC_PriorityGroup: specifies the priority grouping bits length. 
  *   This parameter can be one of the following values:
  *     @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority
  *                                4 bits for subpriority
  *     @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority
  *                                3 bits for subpriority
  *     @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority
  *                                2 bits for subpriority
  *     @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority
  *                                1 bits for subpriority
  *     @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority
  *                                0 bits for subpriority
  * @note   When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. 
  *         The pending IRQ priority will be managed only by the subpriority. 
  * @retval None
  */
void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup)
{
  /* Check the parameters */
  assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup));
  
  /* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */
  SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup;
}

/**
  * @brief  Initializes the NVIC peripheral according to the specified
  *         parameters in the NVIC_InitStruct.
  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
  *         function should be called before. 
  * @param  NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains
  *         the configuration information for the specified NVIC peripheral.
  * @retval None
  */
void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct)
{
  uint8_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F;
  
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd));
  assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority));  
  assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority));
    
  if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE)
  {
    /* Compute the Corresponding IRQ Priority --------------------------------*/    
    tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08;
    tmppre = (0x4 - tmppriority);
    tmpsub = tmpsub >> tmppriority;

    tmppriority = NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre;
    tmppriority |=  (uint8_t)(NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub);
        
    tmppriority = tmppriority << 0x04;
        
    NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority;
    
    /* Enable the Selected IRQ Channels --------------------------------------*/
    NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
  }
  else
  {
    /* Disable the Selected IRQ Channels -------------------------------------*/
    NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
  }
}

/**
  * @brief  Sets the vector table location and Offset.
  * @param  NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory.
  *   This parameter can be one of the following values:
  *     @arg NVIC_VectTab_RAM: Vector Table in internal SRAM.
  *     @arg NVIC_VectTab_FLASH: Vector Table in internal FLASH.
  * @param  Offset: Vector Table base offset field. This value must be a multiple of 0x200.
  * @retval None
  */
void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset)
{ 
  /* Check the parameters */
  assert_param(IS_NVIC_VECTTAB(NVIC_VectTab));
  assert_param(IS_NVIC_OFFSET(Offset));  
   
  SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80);
}

/**
  * @brief  Selects the condition for the system to enter low power mode.
  * @param  LowPowerMode: Specifies the new mode for the system to enter low power mode.
  *   This parameter can be one of the following values:
  *     @arg NVIC_LP_SEVONPEND: Low Power SEV on Pend.
  *     @arg NVIC_LP_SLEEPDEEP: Low Power DEEPSLEEP request.
  *     @arg NVIC_LP_SLEEPONEXIT: Low Power Sleep on Exit.
  * @param  NewState: new state of LP condition. This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_NVIC_LP(LowPowerMode));
  assert_param(IS_FUNCTIONAL_STATE(NewState));  
  
  if (NewState != DISABLE)
  {
    SCB->SCR |= LowPowerMode;
  }
  else
  {
    SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode);
  }
}

/**
  * @brief  Configures the SysTick clock source.
  * @param  SysTick_CLKSource: specifies the SysTick clock source.
  *   This parameter can be one of the following values:
  *     @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source.
  *     @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source.
  * @retval None
  */
void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource)
{
  /* Check the parameters */
  assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource));
  if (SysTick_CLKSource == SysTick_CLKSource_HCLK)
  {
    SysTick->CTRL |= SysTick_CLKSource_HCLK;
  }
  else
  {
    SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8;
  }
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/