/**
  ******************************************************************************
  * @file    stm32h7xx_hal_pwr.h
  * @author  MCD Application Team
  * @brief   Header file of PWR HAL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32H7xx_HAL_PWR_H
#define STM32H7xx_HAL_PWR_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32h7xx_hal_def.h"

/** @addtogroup STM32H7xx_HAL_Driver
  * @{
  */

/** @addtogroup PWR
  * @{
  */

/* Exported types ------------------------------------------------------------*/

/** @defgroup PWR_Exported_Types PWR Exported Types
  * @{
  */

/**
  * @brief  PWR PVD configuration structure definition
  */
typedef struct
{
  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level.
                            This parameter can be a value of @ref PWR_PVD_detection_level */

  uint32_t Mode;      /*!< Mode: Specifies the operating mode for the selected pins.
                           This parameter can be a value of @ref PWR_PVD_Mode             */
}PWR_PVDTypeDef;

/**
  * @}
  */

/* Exported constants --------------------------------------------------------*/
/** @defgroup PWR_Exported_Constants PWR Exported Constants
  * @{
  */

/** @defgroup PWR_PVD_detection_level PWR PVD detection level
  * @{
  */
#define PWR_PVDLEVEL_0  PWR_CR1_PLS_LEV0  /*!< Programmable voltage detector level 0 selection : 1V95        */
#define PWR_PVDLEVEL_1  PWR_CR1_PLS_LEV1  /*!< Programmable voltage detector level 1 selection : 2V1         */
#define PWR_PVDLEVEL_2  PWR_CR1_PLS_LEV2  /*!< Programmable voltage detector level 2 selection : 2V25        */
#define PWR_PVDLEVEL_3  PWR_CR1_PLS_LEV3  /*!< Programmable voltage detector level 3 selection : 2V4         */
#define PWR_PVDLEVEL_4  PWR_CR1_PLS_LEV4  /*!< Programmable voltage detector level 4 selection : 2V55        */
#define PWR_PVDLEVEL_5  PWR_CR1_PLS_LEV5  /*!< Programmable voltage detector level 5 selection : 2V7         */
#define PWR_PVDLEVEL_6  PWR_CR1_PLS_LEV6  /*!< Programmable voltage detector level 6 selection : 2V85        */
#define PWR_PVDLEVEL_7  PWR_CR1_PLS_LEV7  /*!< External input analog voltage (Compare internally to VREFINT) */
/**
  * @}
  */

/** @defgroup PWR_PVD_Mode PWR PVD Mode
  * @{
  */
#define PWR_PVD_MODE_NORMAL                 ((uint32_t)0x00000000U)   /*!< Basic mode is used                                                 */
#define PWR_PVD_MODE_IT_RISING              ((uint32_t)0x00010001U)   /*!< External Interrupt Mode with Rising edge trigger detection         */
#define PWR_PVD_MODE_IT_FALLING             ((uint32_t)0x00010002U)   /*!< External Interrupt Mode with Falling edge trigger detection        */
#define PWR_PVD_MODE_IT_RISING_FALLING      ((uint32_t)0x00010003U)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
#define PWR_PVD_MODE_EVENT_RISING           ((uint32_t)0x00020001U)   /*!< Event Mode with Rising edge trigger detection                      */
#define PWR_PVD_MODE_EVENT_FALLING          ((uint32_t)0x00020002U)   /*!< Event Mode with Falling edge trigger detection                     */
#define PWR_PVD_MODE_EVENT_RISING_FALLING   ((uint32_t)0x00020003U)   /*!< Event Mode with Rising/Falling edge trigger detection              */
/**
  * @}
  */

/** @defgroup PWR_Regulator_state_in_STOP_mode PWR Regulator state in SLEEP/STOP mode
  * @{
  */
#define PWR_MAINREGULATOR_ON      ((uint32_t)0x00000000U)
#define PWR_LOWPOWERREGULATOR_ON  PWR_CR1_LPDS
/**
  * @}
  */

/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
  * @{
  */
#define PWR_SLEEPENTRY_WFI  ((uint8_t)0x01U)
#define PWR_SLEEPENTRY_WFE  ((uint8_t)0x02U)
/**
  * @}
  */

/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
  * @{
  */
#define PWR_STOPENTRY_WFI  ((uint8_t)0x01U)
#define PWR_STOPENTRY_WFE  ((uint8_t)0x02U)
/**
  * @}
  */

/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
  * @{
  */
#define PWR_REGULATOR_VOLTAGE_SCALE0  ((uint32_t)0x00000000)
#define PWR_REGULATOR_VOLTAGE_SCALE1  (PWR_D3CR_VOS_1 | PWR_D3CR_VOS_0)
#define PWR_REGULATOR_VOLTAGE_SCALE2  (PWR_D3CR_VOS_1)
#define PWR_REGULATOR_VOLTAGE_SCALE3  (PWR_D3CR_VOS_0)
/**
  * @}
  */

/** @defgroup PWR_Flag PWR Flag
  * @{
  */
#define PWR_FLAG_STOP       ((uint8_t)0x01U)
#define PWR_FLAG_SB_D1      ((uint8_t)0x02U)
#define PWR_FLAG_SB_D2      ((uint8_t)0x03U)
#define PWR_FLAG_SB         ((uint8_t)0x04U)
#if defined(DUAL_CORE)
#define PWR_FLAG_CPU_HOLD   ((uint8_t)0x05U)
#define PWR_FLAG_CPU2_HOLD  ((uint8_t)0x06U)
#define PWR_FLAG2_STOP      ((uint8_t)0x07U)
#define PWR_FLAG2_SB_D1     ((uint8_t)0x08U)
#define PWR_FLAG2_SB_D2     ((uint8_t)0x09U)
#define PWR_FLAG2_SB        ((uint8_t)0x0AU)
#endif /*DUAL_CORE*/
#define PWR_FLAG_PVDO       ((uint8_t)0x0BU)
#define PWR_FLAG_AVDO       ((uint8_t)0x0CU)
#define PWR_FLAG_ACTVOSRDY  ((uint8_t)0x0DU)
#define PWR_FLAG_ACTVOS     ((uint8_t)0x0EU)
#define PWR_FLAG_BRR        ((uint8_t)0x0FU)
#define PWR_FLAG_VOSRDY     ((uint8_t)0x10U)
#if defined(SMPS)
#define PWR_FLAG_SMPSEXTRDY ((uint8_t)0x11U)
#else
#define PWR_FLAG_SCUEN      ((uint8_t)0x11U)
#endif /* SMPS */
/**
  * @}
  */

/** @defgroup PWR_ENABLE_WUP_Mask PWR Enable WUP Mask
  * @{
  */
#define  PWR_EWUP_MASK  ((uint32_t)0x0FFF3F3FU)
/**
  * @}
  */

/**
  * @}
  */
/* Exported macro ------------------------------------------------------------*/
/** @defgroup PWR_Exported_Macro PWR Exported Macro
  * @{
  */

/** @brief  macros configure the main internal regulator output voltage.
  * @param  __REGULATOR__: specifies the regulator output voltage to achieve
  *         a tradeoff between performance and power consumption when the device does
  *         not operate at the maximum frequency (refer to the datasheets for more details).
  *          This parameter can be one of the following values:
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE0: Regulator voltage output Scale 0 mode
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
  *            @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode
  * @note  PWR_REGULATOR_VOLTAGE_SCALE0 is only possible when Vcore is supplied from LDO.
  *        the SYSCFG Clock must be enabled before selecting PWR_REGULATOR_VOLTAGE_SCALE0
  *        using macro   __HAL_RCC_SYSCFG_CLK_ENABLE().
  *        Transition to PWR_REGULATOR_VOLTAGE_SCALE0 is only possible when the system is already in
  *        PWR_REGULATOR_VOLTAGE_SCALE1.
  *        transition from PWR_REGULATOR_VOLTAGE_SCALE0 is only possible to PWR_REGULATOR_VOLTAGE_SCALE1
  *        then once in PWR_REGULATOR_VOLTAGE_SCALE1 it is possible to switch to another voltage scale.
  *        After each regulator voltage setting, wait on PWR_FLAG_VOSRDY to be set using macro __HAL_PWR_GET_FLAG
  *        To enter low power mode , and if current regulator voltage is PWR_REGULATOR_VOLTAGE_SCALE0 then first
  *        switch to PWR_REGULATOR_VOLTAGE_SCALE1 before entering low power mode.
  *
  * @retval None
  */
#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__)  \
do { \
    __IO uint32_t tmpreg = 0x00; \
    if((__REGULATOR__) == PWR_REGULATOR_VOLTAGE_SCALE0) \
    { \
      MODIFY_REG(PWR->D3CR, PWR_D3CR_VOS, PWR_REGULATOR_VOLTAGE_SCALE1); \
      /* Delay after setting the voltage scaling */  \
      tmpreg = READ_BIT(PWR->D3CR, PWR_D3CR_VOS); \
      MODIFY_REG(SYSCFG->PWRCR, SYSCFG_PWRCR_ODEN, SYSCFG_PWRCR_ODEN); \
      /* Delay after setting the syscfg boost setting */  \
      tmpreg = READ_BIT(SYSCFG->PWRCR, SYSCFG_PWRCR_ODEN); \
    } \
    else \
    { \
      CLEAR_BIT(SYSCFG->PWRCR, SYSCFG_PWRCR_ODEN); \
      /* Delay after setting the syscfg boost setting */  \
      tmpreg = READ_BIT(SYSCFG->PWRCR, SYSCFG_PWRCR_ODEN); \
      MODIFY_REG(PWR->D3CR, PWR_D3CR_VOS, (__REGULATOR__)); \
      tmpreg = READ_BIT(PWR->D3CR, PWR_D3CR_VOS); \
    } \
    UNUSED(tmpreg); \
} while(0)

#if defined(DUAL_CORE)
/** @brief  Check PWR PVD/AVD and VOSflags are set or not.
  * @param  __FLAG__: specifies the flag to check.
  *           This parameter can be one of the following values:
  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode.
  *                  For this reason, this bit is equal to 0 after Standby or reset
  *                  until the PVDE bit is set.
  *            @arg PWR_FLAG_AVDO: AVD Output. This flag is valid only if AVD is enabled
  *                  by the HAL_PWREx_EnableAVD() function. The AVD is stopped by Standby mode.
  *                  For this reason, this bit is equal to 0 after Standby or reset
  *                  until the AVDE bit is set.
  *            @arg PWR_FLAG_ACTVOSRDY: This flag indicates that the Regulator voltage
  *                 scaling output selection is ready.
  *            @arg PWR_FLAG_VOSRDY: This flag indicates that the Regulator voltage
  *                 scaling output selection is ready.
  *            @arg PWR_FLAG_SMPSEXTRDY: SMPS External supply ready flag.
  *            @arg PWR_FLAG_BRR: Backup regulator ready flag. This bit is not reset
  *                  when the device wakes up from Standby mode or by a system reset
  *                  or power reset.
  *            @arg PWR_FLAG_SB: StandBy flag
  *            @arg PWR_FLAG_STOP: STOP flag
  *            @arg PWR_FLAG_SB_D1: StandBy D1 flag
  *            @arg PWR_FLAG_SB_D2: StandBy D2 flag
  *            @arg PWR_FLAG_CPU1_HOLD: CPU1 system wake up with hold
  *            @arg PWR_FLAG_CPU2_HOLD: CPU2 system wake up with hold
  * @retval The new state of __FLAG__ (TRUE or FALSE).
  */
#define __HAL_PWR_GET_FLAG(__FLAG__) ( \
((__FLAG__) == PWR_FLAG_PVDO)?((PWR->CSR1 & PWR_CSR1_PVDO) == PWR_CSR1_PVDO) : \
((__FLAG__) == PWR_FLAG_AVDO)?((PWR->CSR1 & PWR_CSR1_AVDO) == PWR_CSR1_AVDO) : \
((__FLAG__) == PWR_FLAG_ACTVOSRDY)?((PWR->CSR1 & PWR_CSR1_ACTVOSRDY) == PWR_CSR1_ACTVOSRDY) : \
((__FLAG__) == PWR_FLAG_VOSRDY)?((PWR->D3CR & PWR_D3CR_VOSRDY) == PWR_D3CR_VOSRDY) : \
((__FLAG__) == PWR_FLAG_SMPSEXTRDY)?((PWR->CR3 & PWR_CR3_SMPSEXTRDY) == PWR_CR3_SMPSEXTRDY) : \
((__FLAG__) == PWR_FLAG_BRR)?((PWR->CR2 & PWR_CR2_BRRDY) == PWR_CR2_BRRDY) : \
((__FLAG__) == PWR_FLAG_CPU_HOLD)?((PWR->CPU2CR & PWR_CPU2CR_HOLD1F) == PWR_CPU2CR_HOLD1F) : \
((__FLAG__) == PWR_FLAG_CPU2_HOLD)?((PWR->CPUCR & PWR_CPUCR_HOLD2F) == PWR_CPUCR_HOLD2F) : \
((__FLAG__) == PWR_FLAG_SB)?(READ_BIT(PWR->CPUCR, PWR_CPUCR_SBF) == PWR_CPUCR_SBF) : \
((__FLAG__) == PWR_FLAG2_SB)?(READ_BIT(PWR->CPU2CR, PWR_CPU2CR_SBF) == PWR_CPU2CR_SBF) : \
((__FLAG__) == PWR_FLAG_STOP)?(READ_BIT(PWR->CPUCR, PWR_CPUCR_STOPF) == PWR_CPUCR_STOPF) : \
((__FLAG__) == PWR_FLAG2_STOP)?(READ_BIT(PWR->CPU2CR, PWR_CPU2CR_STOPF) == PWR_CPU2CR_STOPF) : \
((__FLAG__) == PWR_FLAG_SB_D1)?(READ_BIT(PWR->CPUCR, PWR_CPUCR_SBF_D1) == PWR_CPUCR_SBF_D1) : \
((__FLAG__) == PWR_FLAG2_SB_D1)?(READ_BIT(PWR->CPU2CR, PWR_CPU2CR_SBF_D1) == PWR_CPU2CR_SBF_D1) : \
((__FLAG__) == PWR_FLAG_SB_D2)?(READ_BIT(PWR->CPUCR, PWR_CPUCR_SBF_D2) == PWR_CPUCR_SBF_D2) : \
(READ_BIT(PWR->CPU2CR, PWR_CPU2CR_SBF_D2) == PWR_CPU2CR_SBF_D2))
#else
/** @brief  Check PWR PVD/AVD and VOSflags are set or not.
  * @param  __FLAG__: specifies the flag to check.
  *           This parameter can be one of the following values:
  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode.
  *                  For this reason, this bit is equal to 0 after Standby or reset
  *                  until the PVDE bit is set.
  *            @arg PWR_FLAG_AVDO: AVD Output. This flag is valid only if AVD is enabled
  *                  by the HAL_PWREx_EnableAVD() function. The AVD is stopped by Standby mode.
  *                  For this reason, this bit is equal to 0 after Standby or reset
  *                  until the AVDE bit is set.
  *            @arg PWR_FLAG_ACTVOSRDY: This flag indicates that the Regulator voltage
  *                 scaling output selection is ready.
  *            @arg PWR_FLAG_VOSRDY: This flag indicates that the Regulator voltage
  *                 scaling output selection is ready.
  *            @arg PWR_FLAG_BRR: Backup regulator ready flag. This bit is not reset
  *                  when the device wakes up from Standby mode or by a system reset
  *                  or power reset.
  *            @arg PWR_FLAG_SB: StandBy flag
  *            @arg PWR_FLAG_STOP: STOP flag
  *            @arg PWR_FLAG_SB_D1: StandBy D1 flag
  *            @arg PWR_FLAG_SB_D2: StandBy D2 flag
  * @retval The new state of __FLAG__ (TRUE or FALSE).
  */
#define __HAL_PWR_GET_FLAG(__FLAG__) ( \
((__FLAG__) == PWR_FLAG_PVDO)?((PWR->CSR1 & PWR_CSR1_PVDO) == PWR_CSR1_PVDO) : \
((__FLAG__) == PWR_FLAG_AVDO)?((PWR->CSR1 & PWR_CSR1_AVDO) == PWR_CSR1_AVDO) : \
((__FLAG__) == PWR_FLAG_ACTVOSRDY)?((PWR->CSR1 & PWR_CSR1_ACTVOSRDY) == PWR_CSR1_ACTVOSRDY) : \
((__FLAG__) == PWR_FLAG_VOSRDY)?((PWR->D3CR & PWR_D3CR_VOSRDY) == PWR_D3CR_VOSRDY) : \
((__FLAG__) == PWR_FLAG_SCUEN)?((PWR->CR3 & PWR_CR3_SCUEN) == PWR_CR3_SCUEN) : \
((__FLAG__) == PWR_FLAG_BRR)?((PWR->CR2 & PWR_CR2_BRRDY) == PWR_CR2_BRRDY) : \
((__FLAG__) == PWR_FLAG_SB)?((PWR->CPUCR & PWR_CPUCR_SBF) == PWR_CPUCR_SBF) : \
((__FLAG__) == PWR_FLAG_STOP)?((PWR->CPUCR & PWR_CPUCR_STOPF) == PWR_CPUCR_STOPF) : \
((__FLAG__) == PWR_FLAG_SB_D1)?((PWR->CPUCR & PWR_CPUCR_SBF_D1) == PWR_CPUCR_SBF_D1) : \
((PWR->CPUCR & PWR_CPUCR_SBF_D2) == PWR_CPUCR_SBF_D2))
#endif /*DUAL_CORE*/


#if defined(DUAL_CORE)
/** @brief  Clear PWR flags.
  * @param  __FLAG__: specifies the flag to clear.
  *           This parameter can be one of the following values:
  *            @arg PWR_FLAG_SB: Standby flag.
  *            @arg PWR_CPU_FLAGS: Clear HOLD2F, STOPF, SBF, SBF_D1, and SBF_D2 CPU flags.
  * @retval None.
  */
#define __HAL_PWR_CLEAR_FLAG(__FLAG__)      \
do {                                        \
     SET_BIT(PWR->CPUCR, PWR_CPUCR_CSSF);   \
     SET_BIT(PWR->CPU2CR, PWR_CPU2CR_CSSF); \
} while(0)
#else
/** @brief  Clear PWR flags.
  * @param  __FLAG__: specifies the flag to clear.
  *           This parameter can be one of the following values:
  *            @arg PWR_FLAG_SB: Standby flag.
  *            @arg PWR_CPU_FLAGS: Clear STOPF, SBF, SBF_D1, and SBF_D2 CPU flags.
  * @retval None.
  */
#define __HAL_PWR_CLEAR_FLAG(__FLAG__)  SET_BIT(PWR->CPUCR, PWR_CPUCR_CSSF)
#endif /*DUAL_CORE*/

/**
  * @brief Enable the PVD EXTI Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_IT()  SET_BIT(EXTI->IMR1, PWR_EXTI_LINE_PVD)

#if defined(DUAL_CORE)
/**
  * @brief Enable the PVD EXTI D2 Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTID2_ENABLE_IT()  SET_BIT(EXTI_D2->IMR1, PWR_EXTI_LINE_PVD)
#endif /*DUAL_CORE*/

/**
  * @brief Disable the PVD EXTI Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_IT()  CLEAR_BIT(EXTI->IMR1, PWR_EXTI_LINE_PVD)

#if defined(DUAL_CORE)
/**
  * @brief Disable the PVD EXTI D2 Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTID2_DISABLE_IT()  CLEAR_BIT(EXTI_D2->IMR1, PWR_EXTI_LINE_PVD)
#endif /*DUAL_CORE*/

/**
  * @brief   Enable event on PVD EXTI Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()  SET_BIT(EXTI->EMR1, PWR_EXTI_LINE_PVD)

#if defined(DUAL_CORE)
/**
  * @brief   Enable event on PVD EXTI D2 Line.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTID2_ENABLE_EVENT()  SET_BIT(EXTI_D2->EMR1, PWR_EXTI_LINE_PVD)
#endif /*DUAL_CORE*/

/**
  * @brief   Disable event on PVD EXTI Line 16.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  CLEAR_BIT(EXTI->EMR1, PWR_EXTI_LINE_PVD)

#if defined(DUAL_CORE)
/**
  * @brief   Disable event on PVD EXTI D2 Line.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTID2_DISABLE_EVENT()  CLEAR_BIT(EXTI_D2->EMR1, PWR_EXTI_LINE_PVD)
#endif /*DUAL_CORE*/

/**
  * @brief Enable the PVD Extended Interrupt Rising Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()  SET_BIT(EXTI->RTSR1, PWR_EXTI_LINE_PVD)

/**
  * @brief Disable the PVD Extended Interrupt Rising Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR1, PWR_EXTI_LINE_PVD)

/**
  * @brief Enable the PVD Extended Interrupt Falling Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  SET_BIT(EXTI->FTSR1, PWR_EXTI_LINE_PVD)


/**
  * @brief Disable the PVD Extended Interrupt Falling Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR1, PWR_EXTI_LINE_PVD)


/**
  * @brief  PVD EXTI line configuration: set rising & falling edge trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() \
do { \
      __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); \
      __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); \
} while(0);

/**
  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() \
do { \
      __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); \
      __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); \
} while(0);

/**
  * @brief  Check whether the specified PVD EXTI interrupt flag is set or not.
  * @retval EXTI PVD Line Status.
  */
#define __HAL_PWR_PVD_EXTI_GET_FLAG()  ((READ_BIT(EXTI->PR1, PWR_EXTI_LINE_PVD) == PWR_EXTI_LINE_PVD) ? SET : RESET)


#if defined(DUAL_CORE)
/**
  * @brief checks whether the specified PVD Exti interrupt flag is set or not.
  * @retval EXTI D2 PVD Line Status.
  */
#define __HAL_PWR_PVD_EXTID2_GET_FLAG()  ((READ_BIT(EXTI_D2->PR1, PWR_EXTI_LINE_PVD) == PWR_EXTI_LINE_PVD) ? SET : RESET)
#endif /*DUAL_CORE*/

/**
  * @brief Clear the PVD EXTI flag.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()  SET_BIT(EXTI->PR1, PWR_EXTI_LINE_PVD)

#if defined(DUAL_CORE)
/**
  * @brief Clear the PVD EXTI D2 flag.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTID2_CLEAR_FLAG()    SET_BIT(EXTI_D2->PR1, PWR_EXTI_LINE_PVD)
#endif /*DUAL_CORE*/

/**
  * @brief  Generates a Software interrupt on PVD EXTI line.
  * @retval None.
  */
#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()    SET_BIT(EXTI->SWIER1, PWR_EXTI_LINE_PVD)
/**
  * @}
  */


/* Include PWR HAL Extension module */
#include "stm32h7xx_hal_pwr_ex.h"

/* Exported functions --------------------------------------------------------*/
/** @addtogroup PWR_Exported_Functions PWR Exported Functions
  * @{
  */

/** @addtogroup PWR_Exported_Functions_Group1 Initialization and De-Initialization functions
  * @{
  */
/* Initialization and de-initialization functions *****************************/
void HAL_PWR_DeInit(void);
void HAL_PWR_EnableBkUpAccess(void);
void HAL_PWR_DisableBkUpAccess(void);
/**
  * @}
  */

/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions
  * @{
  */
/* Peripheral Control functions  **********************************************/
/* PVD configuration */
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
void HAL_PWR_EnablePVD(void);
void HAL_PWR_DisablePVD(void);

/* WakeUp pins configuration */
void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinPolarity);
void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);

/* Low Power modes entry */
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
void HAL_PWR_EnterSTANDBYMode(void);

/* Power PVD IRQ Handler */
void HAL_PWR_PVD_IRQHandler(void);
void HAL_PWR_PVDCallback(void);

/* Cortex System Control functions  *******************************************/
void HAL_PWR_EnableSleepOnExit(void);
void HAL_PWR_DisableSleepOnExit(void);
void HAL_PWR_EnableSEVOnPend(void);
void HAL_PWR_DisableSEVOnPend(void);
/**
  * @}
  */

/**
  * @}
  */

/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup PWR_Private_Constants PWR Private Constants
  * @{
  */

/** @defgroup PWR_PVD_EXTI_Line PWR PVD EXTI Line
  * @{
  */
/*!< External interrupt line 16 Connected to the PVD EXTI Line */
#define PWR_EXTI_LINE_PVD      ((uint32_t)EXTI_IMR1_IM16)
/**
  * @}
  */

/**
  * @}
  */
/* Private macros ------------------------------------------------------------*/
/** @defgroup PWR_Private_Macros PWR Private Macros
  * @{
  */

/** @defgroup PWR_IS_PWR_Definitions PWR Private macros to check input parameters
  * @{
  */
#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))

#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
                              ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
                              ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
                              ((MODE) == PWR_PVD_MODE_NORMAL))

#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))

#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))

#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
#define IS_PWR_REGULATOR_VOLTAGE(VOLTAGE) (((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
                                           ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
                                           ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE3))

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

#ifdef __cplusplus
}
#endif


#endif /* STM32H7xx_HAL_PWR_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/