/**************************************************************************//**
 * @file     i2c.c
 * @version  V3.00
 * $Revision: 2 $
 * $Date: 16/08/02 6:02p $
 * @brief    M2351 series I2C Serial Interface Controller(I2C) driver source file
 *
 * @note
 * Copyright (C) 2016 Nuvoton Technology Corp. All rights reserved.
 *****************************************************************************/
#include "NuMicro.h"

/** @addtogroup Standard_Driver Standard Driver
  @{
*/

/** @addtogroup I2C_Driver I2C Driver
  @{
*/


/** @addtogroup I2C_EXPORTED_FUNCTIONS I2C Exported Functions
  @{
*/

/**
  * @brief      Enable specify I2C Controller and set Clock Divider
  *
  * @param[in]  i2c         Specify I2C port
  * @param[in]  u32BusClock The target I2C bus clock in Hz
  *
  * @return     Actual I2C bus clock frequency
  *
  * @details    The function enable the specify I2C Controller and set proper Clock Divider
  *             in I2C CLOCK DIVIDED REGISTER (I2CLK) according to the target I2C Bus clock.
  *             I2C Bus clock = PCLK / (4*(divider+1).
  *
  */
uint32_t I2C_Open(I2C_T *i2c, uint32_t u32BusClock)
{
    uint32_t u32Div;
    uint32_t u32Pclk;

    if((i2c == I2C1) || (i2c == I2C1_NS))
    {
        u32Pclk = CLK_GetPCLK1Freq();
    }
    else
    {
        u32Pclk = CLK_GetPCLK0Freq();
    }

    u32Div = (uint32_t)(((u32Pclk * 10u) / (u32BusClock * 4u) + 5u) / 10u - 1u); /* Compute proper divider for I2C clock */
    i2c->CLKDIV = u32Div;

    /* Enable I2C */
    i2c->CTL0 |= I2C_CTL0_I2CEN_Msk;

    return (u32Pclk / ((u32Div + 1u) << 2u));
}

/**
  * @brief      Disable specify I2C Controller
  *
  * @param[in]  i2c         Specify I2C port
    *
  * @return     None
  *
  * @details    Reset I2C Controller and disable specify I2C port.
    *
  */

void I2C_Close(I2C_T *i2c)
{
    /* Reset I2C Controller */
    if(i2c ==  I2C0)
    {
        SYS->IPRST1 |= SYS_IPRST1_I2C0RST_Msk;
        SYS->IPRST1 &= ~SYS_IPRST1_I2C0RST_Msk;
    }
    else if(i2c ==  I2C1)
    {
        SYS->IPRST1 |= SYS_IPRST1_I2C1RST_Msk;
        SYS->IPRST1 &= ~SYS_IPRST1_I2C1RST_Msk;
    }
    else if(i2c ==  I2C2)
    {
        SYS->IPRST1 |= SYS_IPRST1_I2C2RST_Msk;
        SYS->IPRST1 &= ~SYS_IPRST1_I2C2RST_Msk;
    }

    /* Disable I2C */
    i2c->CTL0 &= ~I2C_CTL0_I2CEN_Msk;
}

/**
  * @brief      Clear Time-out Counter flag
  *
  * @param[in]  i2c         Specify I2C port
    *
  * @return     None
  *
  * @details    When Time-out flag will be set, use this function to clear I2C Bus Time-out counter flag .
    *
  */
void I2C_ClearTimeoutFlag(I2C_T *i2c)
{
    i2c->TOCTL |= I2C_TOCTL_TOIF_Msk;
}

/**
  * @brief      Set Control bit of I2C Controller
  *
  * @param[in]  i2c         Specify I2C port
  * @param[in]  u8Start     Set I2C START condition
  * @param[in]  u8Stop      Set I2C STOP condition
  * @param[in]  u8Si        Clear SI flag
  * @param[in]  u8Ack       Set I2C ACK bit
  *
  * @return     None
  *
  * @details    The function set I2C Control bit of I2C Bus protocol.
  *
  */
void I2C_Trigger(I2C_T *i2c, uint8_t u8Start, uint8_t u8Stop, uint8_t u8Si, uint8_t u8Ack)
{
    uint32_t u32Reg = 0u;

    if(u8Start)
    {
        u32Reg |= I2C_CTL_STA;
    }
    if(u8Stop)
    {
        u32Reg |= I2C_CTL_STO;
    }
    if(u8Si)
    {
        u32Reg |= I2C_CTL_SI;
    }
    if(u8Ack)
    {
        u32Reg |= I2C_CTL_AA;
    }

    i2c->CTL0 = (i2c->CTL0 & ~0x3Cu) | u32Reg;
}

/**
  * @brief      Disable Interrupt of I2C Controller
  *
  * @param[in]  i2c         Specify I2C port
  *
  * @return     None
  *
  * @details    The function is used for disable I2C interrupt
  *
  */
void I2C_DisableInt(I2C_T *i2c)
{
    i2c->CTL0 &= ~I2C_CTL0_INTEN_Msk;
}

/**
  * @brief      Enable Interrupt of I2C Controller
  *
  * @param[in]  i2c         Specify I2C port
  *
  * @return     None
  *
  * @details    The function is used for enable I2C interrupt
  *
  */
void I2C_EnableInt(I2C_T *i2c)
{
    i2c->CTL0 |= I2C_CTL0_INTEN_Msk;
}

/**
 * @brief      Get I2C Bus Clock
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     The actual I2C Bus clock in Hz
 *
 * @details    To get the actual I2C Bus Clock frequency.
 */
uint32_t I2C_GetBusClockFreq(I2C_T *i2c)
{
    uint32_t u32Divider = i2c->CLKDIV;
    uint32_t u32Pclk;

    if((i2c == I2C1) || (i2c == I2C1_NS))
    {
        u32Pclk = CLK_GetPCLK1Freq();
    }
    else
    {
        u32Pclk = CLK_GetPCLK0Freq();
    }

    return (u32Pclk / ((u32Divider + 1u) << 2u));
}

/**
 * @brief      Set I2C Bus Clock
 *
 * @param[in]  i2c          Specify I2C port
 * @param[in]  u32BusClock  The target I2C Bus Clock in Hz
 *
 * @return     The actual I2C Bus Clock in Hz
 *
 * @details    To set the actual I2C Bus Clock frequency.
 */
uint32_t I2C_SetBusClockFreq(I2C_T *i2c, uint32_t u32BusClock)
{
    uint32_t u32Div;
    uint32_t u32Pclk;

    if((i2c == I2C1) || (i2c == I2C1_NS))
    {
        u32Pclk = CLK_GetPCLK1Freq();
    }
    else
    {
        u32Pclk = CLK_GetPCLK0Freq();
    }

    u32Div = (uint32_t)(((u32Pclk * 10u) / (u32BusClock * 4u) + 5u) / 10u - 1u); /* Compute proper divider for I2C clock */
    i2c->CLKDIV = u32Div;

    return (u32Pclk / ((u32Div + 1u) << 2u));
}

/**
 * @brief      Get Interrupt Flag
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     I2C interrupt flag status
 *
 * @details    To get I2C Bus interrupt flag.
 */
uint32_t I2C_GetIntFlag(I2C_T *i2c)
{
    return ((i2c->CTL0 & I2C_CTL0_SI_Msk) == I2C_CTL0_SI_Msk ? 1ul : 0ul);
}

/**
 * @brief      Get I2C Bus Status Code
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     I2C Status Code
 *
 * @details    To get I2C Bus Status Code.
 */
uint32_t I2C_GetStatus(I2C_T *i2c)
{
    return (i2c->STATUS0);
}

/**
 * @brief      Read a Byte from I2C Bus
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     I2C Data
 *
 * @details    To read a bytes data from specify I2C port.
 */
uint8_t I2C_GetData(I2C_T *i2c)
{
    return (uint8_t)(i2c->DAT);
}

/**
 * @brief      Send a byte to I2C Bus
 *
 * @param[in]  i2c          Specify I2C port
 * @param[in]  u8Data       The data to send to I2C bus
 *
 * @return     None
 *
 * @details    This function is used to write a byte to specified I2C port
 */
void I2C_SetData(I2C_T *i2c, uint8_t u8Data)
{
    i2c->DAT = u8Data;
}

/**
 * @brief      Set 7-bit Slave Address and GC Mode
 *
 * @param[in]  i2c          Specify I2C port
 * @param[in]  u8SlaveNo    Set the number of I2C address register (0~3)
 * @param[in]  u8SlaveAddr  7-bit slave address
 * @param[in]  u8GCMode     Enable/Disable GC mode (I2C_GCMODE_ENABLE / I2C_GCMODE_DISABLE)
 *
 * @return     None
 *
 * @details    This function is used to set 7-bit slave addresses in I2C SLAVE ADDRESS REGISTER (I2CADDR0~3)
 *             and enable GC Mode.
 *
 */
void I2C_SetSlaveAddr(I2C_T *i2c, uint8_t u8SlaveNo, uint8_t u8SlaveAddr, uint8_t u8GCMode)
{
    switch(u8SlaveNo)
    {
        case 1:
            i2c->ADDR1  = ((uint32_t)u8SlaveAddr << 1) | u8GCMode;
            break;
        case 2:
            i2c->ADDR2  = ((uint32_t)u8SlaveAddr << 1) | u8GCMode;
            break;
        case 3:
            i2c->ADDR3  = ((uint32_t)u8SlaveAddr << 1) | u8GCMode;
            break;
        case 0:
        default:
            i2c->ADDR0  = ((uint32_t)u8SlaveAddr << 1) | u8GCMode;
            break;
    }
}

/**
 * @brief      Configure the mask bits of 7-bit Slave Address
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u8SlaveNo        Set the number of I2C address mask register (0~3)
 * @param[in]  u8SlaveAddrMask  A byte for slave address mask
 *
 * @return     None
 *
 * @details    This function is used to set 7-bit slave addresses.
 *
 */
void I2C_SetSlaveAddrMask(I2C_T *i2c, uint8_t u8SlaveNo, uint8_t u8SlaveAddrMask)
{
    switch(u8SlaveNo)
    {
        case 1:
            i2c->ADDRMSK1  = (uint32_t)u8SlaveAddrMask << 1;
            break;
        case 2:
            i2c->ADDRMSK2  = (uint32_t)u8SlaveAddrMask << 1;
            break;
        case 3:
            i2c->ADDRMSK3  = (uint32_t)u8SlaveAddrMask << 1;
            break;
        case 0:
        default:
            i2c->ADDRMSK0  = (uint32_t)u8SlaveAddrMask << 1;
            break;
    }
}

/**
 * @brief      Enable Time-out Counter Function and support Long Time-out
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u8LongTimeout    Configure DIV4 to enable Long Time-out (0/1)
 *
 * @return     None
 *
 * @details    This function enable Time-out Counter function and configure DIV4 to support Long
 *             Time-out.
 *
 */
void I2C_EnableTimeout(I2C_T *i2c, uint8_t u8LongTimeout)
{
    if(u8LongTimeout)
    {
        i2c->TOCTL |= I2C_TOCTL_TOCDIV4_Msk;
    }
    else
    {
        i2c->TOCTL &= ~I2C_TOCTL_TOCDIV4_Msk;
    }

    i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk;
}

/**
 * @brief      Disable Time-out Counter Function
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     None
 *
 * @details    To disable Time-out Counter function in I2CTOC register.
 *
 */
void I2C_DisableTimeout(I2C_T *i2c)
{
    i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk;
}

/**
 * @brief      Enable I2C Wake-up Function
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     None
 *
 * @details    To enable Wake-up function of I2C Wake-up control register.
 *
 */
void I2C_EnableWakeup(I2C_T *i2c)
{
    i2c->WKCTL |= I2C_WKCTL_WKEN_Msk;
}

/**
 * @brief      Disable I2C Wake-up Function
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     None
 *
 * @details    To disable Wake-up function of I2C Wake-up control register.
 *
 */
void I2C_DisableWakeup(I2C_T *i2c)
{
    i2c->WKCTL &= ~I2C_WKCTL_WKEN_Msk;
}

/**
 * @brief      To get SMBus Status
 *
 * @param[in]  i2c          Specify I2C port
 *
 * @return     SMBus status
 *
 * @details    To get the Bus Management status of I2C_BUSSTS register
 *
 */
uint32_t I2C_SMBusGetStatus(I2C_T *i2c)
{
    return (i2c->BUSSTS);
}

/**
 * @brief      Clear SMBus Interrupt Flag
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u8SMBusIntFlag   Specify SMBus interrupt flag
 *
 * @return     None
 *
 * @details    To clear flags of I2C_BUSSTS status register if interrupt set.
 *
 */
void I2C_SMBusClearInterruptFlag(I2C_T *i2c, uint8_t u8SMBusIntFlag)
{
    i2c->BUSSTS = u8SMBusIntFlag;
}

/**
 * @brief      Set SMBus Bytes Counts of Transmission or Reception
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u32PktSize       Transmit / Receive bytes
 *
 * @return     None
 *
 * @details    The transmission or receive byte number in one transaction when PECEN is set. The maximum is 255 bytes.
 *
 */
void I2C_SMBusSetPacketByteCount(I2C_T *i2c, uint32_t u32PktSize)
{
    i2c->PKTSIZE = u32PktSize;
}

/**
 * @brief      Init SMBus Host/Device Mode
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u8HostDevice     Init SMBus port mode(I2C_SMBH_ENABLE(1)/I2C_SMBD_ENABLE(0))
 *
 * @return     None
 *
 * @details    Using SMBus communication must specify the port is a Host or a Device.
 *
 */
void I2C_SMBusOpen(I2C_T *i2c, uint8_t u8HostDevice)
{
    /* Clear  BMHEN, BMDEN of BUSCTL Register */
    i2c->BUSCTL &=  ~(I2C_BUSCTL_BMHEN_Msk | I2C_BUSCTL_BMDEN_Msk);

    /* Set SMBus Host/Device Mode, and enable Bus Management*/
    if(u8HostDevice == (uint8_t)I2C_SMBH_ENABLE)
    {
        i2c->BUSCTL |= (I2C_BUSCTL_BMHEN_Msk | I2C_BUSCTL_BUSEN_Msk);
    }
    else
    {
        i2c->BUSCTL |= (I2C_BUSCTL_BMDEN_Msk | I2C_BUSCTL_BUSEN_Msk);
    }
}

/**
 * @brief      Disable SMBus function
 *
 * @param[in]  i2c              Specify I2C port
 *
 * @return     None
 *
 * @details    Disable all SMBus function include Bus disable, CRC check, Acknowledge by manual, Host/Device Mode.
 *
 */
void I2C_SMBusClose(I2C_T *i2c)
{

    i2c->BUSCTL = 0x00U;
}

/**
 * @brief      Enable SMBus PEC Transmit Function
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u8PECTxEn        CRC transmit enable(PECTX_ENABLE) or disable(PECTX_DISABLE)
 *
 * @return     None
 *
 * @details    When enable CRC check function, the Host or Device needs to transmit CRC byte.
 *
 */
void I2C_SMBusPECTxEnable(I2C_T *i2c, uint8_t u8PECTxEn)
{
    i2c->BUSCTL &= ~I2C_BUSCTL_PECTXEN_Msk;

    if(u8PECTxEn)
    {
        i2c->BUSCTL |= (I2C_BUSCTL_PECEN_Msk | I2C_BUSCTL_PECTXEN_Msk);
    }
    else
    {
        i2c->BUSCTL |= I2C_BUSCTL_PECEN_Msk;
    }
}

/**
 * @brief      Get SMBus CRC value
 *
 * @param[in]  i2c              Specify I2C port
 *
 * @return     A byte is packet error check value
 *
 * @details    The CRC check value after a transmission or a reception by count by using CRC8
 *
 */
uint8_t I2C_SMBusGetPECValue(I2C_T *i2c)
{
    return (uint8_t)i2c->PKTCRC;
}

/**
 * @brief      Calculate Time-out of SMBus idle period
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  u32Us               Time-out length(us)
 * @param[in]  u32Hclk          I2C peripheral clock frequency
 *
 * @return     None
 *
 * @details    This function is used to set SMBus Time-out length when bus is in Idle state.
 *
 */

void I2C_SMBusIdleTimeout(I2C_T *i2c, uint32_t u32Us, uint32_t u32Hclk)
{
    uint32_t  u32Div, u32HclkKHz;

    i2c->BUSCTL |= I2C_BUSCTL_TIDLE_Msk;
    u32HclkKHz = u32Hclk / 1000U;
    u32Div = (((u32Us * u32HclkKHz) / 1000U) >> 2U) - 1U;
    if(u32Div > 255U)
    {
        i2c->BUSTOUT = 0xFFU;
    }
    else
    {
        i2c->BUSTOUT = u32Div;
    }

}

/**
 * @brief      Calculate Time-out of SMBus active period
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  ms               Time-out length(ms)
 * @param[in]  u32Pclk          peripheral clock frequency
 *
 * @return     None
 *
 * @details    This function is used to set SMBus Time-out length when bus is in active state.
 *             Time-out length is calculate the SCL line "one clock" pull low timing.
 *
 */

void I2C_SMBusTimeout(I2C_T *i2c, uint32_t ms, uint32_t u32Pclk)
{
    uint32_t u32Div, u32Pclk_kHz;

    i2c->BUSCTL &= ~I2C_BUSCTL_TIDLE_Msk;

    /* DIV4 disabled */
    i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk;
    u32Pclk_kHz = u32Pclk / 1000U;
    u32Div = ((ms * u32Pclk_kHz) / (16U * 1024U)) - 1U;
    if(u32Div <= 0xFFU)
    {
        i2c->BUSTOUT = u32Div;
    }
    else
    {
        /* DIV4 enabled */
        i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk;
        i2c->BUSTOUT = (((ms * u32Pclk_kHz) / (16U * 1024U * 4U)) - 1U) & 0xFFU; /* The max value is 255 */
    }
}

/**
 * @brief      Calculate Cumulative Clock low Time-out of SMBus active period
 *
 * @param[in]  i2c              Specify I2C port
 * @param[in]  ms               Time-out length(ms)
 * @param[in]  u32Pclk          peripheral clock frequency
 *
 * @return     None
 *
 * @details    This function is used to set SMBus Time-out length when bus is in Active state.
 *             Time-out length is calculate the SCL line "clocks" low cumulative timing.
 *
 */

void I2C_SMBusClockLoTimeout(I2C_T *i2c, uint32_t ms, uint32_t u32Pclk)
{
    uint32_t u32Div, u32Pclk_kHz;

    i2c->BUSCTL &= ~I2C_BUSCTL_TIDLE_Msk;

    /* DIV4 disabled */
    i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk;
    u32Pclk_kHz = u32Pclk / 1000U;
    u32Div = ((ms * u32Pclk_kHz) / (16U * 1024U)) - 1U;
    if(u32Div <= 0xFFU)
    {
        i2c->CLKTOUT = u32Div;
    }
    else
    {
        /* DIV4 enabled */
        i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk;
        i2c->CLKTOUT = (((ms * u32Pclk_kHz) / (16U * 1024U * 4U)) - 1U) & 0xFFU; /* The max value is 255 */
    }
}

/**
  * @brief      Write a byte to Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u8Data            Write a byte data to Slave
  *
  * @retval     0               Write data success
  * @retval     1               Write data fail, or bus occurs error events
  *
  * @details    The function is used for I2C Master write a byte data to Slave.
  *
  */

uint8_t I2C_WriteByte(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8Data)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;

    I2C_START(i2c);
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));    /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                              /* Clear SI */
                break;
            case 0x18u:                                           /* Slave Address ACK */
                I2C_SET_DATA(i2c, u8Data);                          /* Write data to I2CDAT */
                break;
            case 0x20u:                                           /* Slave Address NACK */
            case 0x30u:                                           /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                          /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                u8Ctrl = I2C_CTL_STO_SI;                          /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                           /* Arbitration Lost */
            default:                                              /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                          /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                        /* Write controlbit to I2C_CTL register */
    }
    return (u8Err | u8Xfering);                                  /* return (Success)/(Fail) status */
}

/**
  * @brief      Write multi bytes to Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  *au8Data           Pointer to array to write data to Slave
  * @param[in]  u32wLen         How many bytes need to write to Slave
  *
  * @return     A length of how many bytes have been transmitted.
  *
  * @details    The function is used for I2C Master write multi bytes data to Slave.
  *
  */

uint32_t I2C_WriteMultiBytes(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t au8Data[], uint32_t u32wLen)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
    uint32_t u32txLen = 0u;

    I2C_START(i2c);                                              /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));    /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                           /* Clear SI */
                break;
            case 0x18u:                                           /* Slave Address ACK */
            case 0x28u:
                if(u32txLen < u32wLen)
                {
                    I2C_SET_DATA(i2c, au8Data[u32txLen++]);                /* Write Data to I2CDAT */
                }
                else
                {
                    u8Ctrl = I2C_CTL_STO_SI;                   /* Clear SI and send STOP */
                    u8Xfering = 0u;
                }
                break;
            case 0x20u:                                           /* Slave Address NACK */
            case 0x30u:                                           /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                       /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x38u:                                           /* Arbitration Lost */
            default:                                             /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                       /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                        /* Write controlbit to I2C_CTL register */
    }
    return u32txLen;                                             /* Return bytes length that have been transmitted */
}

/**
  * @brief      Specify a byte register address and write a byte to Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u8DataAddr      Specify a address (1 byte) of data write to
  * @param[in]  u8Data            A byte data to write it to Slave
  *
  * @retval     0               Write data success
  * @retval     1               Write data fail, or bus occurs error events
  *
  * @details    The function is used for I2C Master specify a address that data write to in Slave.
  *
  */

uint8_t I2C_WriteByteOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr, uint8_t u8Data)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
    uint32_t u32txLen = 0u;

    I2C_START(i2c);                                              /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));    /* Send Slave address with write bit */
                u8Ctrl = I2C_CTL_SI;                           /* Clear SI */
                break;
            case 0x18u:                                           /* Slave Address ACK */
                I2C_SET_DATA(i2c, u8DataAddr);                   /* Write Lo byte address of register */
                break;
            case 0x20u:                                           /* Slave Address NACK */
            case 0x30u:                                           /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                       /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                if(u32txLen < 1u)
                {
                    I2C_SET_DATA(i2c, u8Data);
                    u32txLen++;
                }
                else
                {
                    u8Ctrl = I2C_CTL_STO_SI;                   /* Clear SI and send STOP */
                    u8Xfering = 0u;
                }
                break;
            case 0x38u:                                           /* Arbitration Lost */
            default:                                             /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                       /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                        /* Write controlbit to I2C_CTL register */
    }
    return (u8Err | u8Xfering);                                  /* return (Success)/(Fail) status */
}


/**
  * @brief      Specify a byte register address and write multi bytes to Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u8DataAddr      Specify a address (1 byte) of data write to
  * @param[in]  *au8Data           Pointer to array to write data to Slave
  * @param[in]  u32wLen         How many bytes need to write to Slave
  *
  * @return     A length of how many bytes have been transmitted.
  *
  * @details    The function is used for I2C Master specify a byte address that multi data bytes write to in Slave.
  *
  */

uint32_t I2C_WriteMultiBytesOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr, uint8_t au8Data[], uint32_t u32wLen)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
    uint32_t u32txLen = 0u;

    I2C_START(i2c);                                              /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));    /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;
                break;
            case 0x18u:                                           /* Slave Address ACK */
                I2C_SET_DATA(i2c, u8DataAddr);                   /* Write Lo byte address of register */
                break;
            case 0x20u:                                           /* Slave Address NACK */
            case 0x30u:                                           /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                       /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                if(u32txLen < u32wLen)
                {
                    I2C_SET_DATA(i2c, au8Data[u32txLen++]);
                }
                else
                {
                    u8Ctrl = I2C_CTL_STO_SI;                   /* Clear SI and send STOP */
                    u8Xfering = 0u;
                }
                break;
            case 0x38u:                                           /* Arbitration Lost */
            default:                                             /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                       /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                        /* Write controlbit to I2C_CTL register */
    }

    return u32txLen;                                             /* Return bytes length that have been transmitted */
}

/**
  * @brief      Specify two bytes register address and Write a byte to Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u16DataAddr     Specify a address (2 byte) of data write to
  * @param[in]  u8Data            Write a byte data to Slave
  *
  * @retval     0               Write data success
  * @retval     1               Write data fail, or bus occurs error events
  *
  * @details    The function is used for I2C Master specify two bytes address that data write to in Slave.
  *
  */

uint8_t I2C_WriteByteTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr, uint8_t u8Data)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Addr = 1u, u8Ctrl = 0u;
    uint32_t u32txLen = 0u;

    I2C_START(i2c);                                                         /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));               /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x18u:                                                      /* Slave Address ACK */
                I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u));    /* Write Hi byte address of register */
                break;
            case 0x20u:                                                      /* Slave Address NACK */
            case 0x30u:                                                      /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                if(u8Addr)
                {
                    I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu));       /* Write Lo byte address of register */
                    u8Addr = 0u;
                }
                else if((u32txLen < 1u) && (u8Addr == 0u))
                {
                    I2C_SET_DATA(i2c, u8Data);
                    u32txLen++;
                }
                else
                {
                    u8Ctrl = I2C_CTL_STO_SI;                              /* Clear SI and send STOP */
                    u8Xfering = 0u;
                }
                break;
            case 0x38u:                                                      /* Arbitration Lost */
            default:                                                        /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                                   /* Write controlbit to I2C_CTL register */
    }
    return (u8Err | u8Xfering);                                             /* return (Success)/(Fail) status */
}


/**
  * @brief      Specify two bytes register address and write multi bytes to Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u16DataAddr     Specify a address (2 bytes) of data write to
  * @param[in]  au8Data[]          A data array for write data to Slave
  * @param[in]  u32wLen         How many bytes need to write to Slave
  *
  * @return     A length of how many bytes have been transmitted.
  *
  * @details    The function is used for I2C Master specify a byte address that multi data write to in Slave.
  *
  */

uint32_t I2C_WriteMultiBytesTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr, uint8_t au8Data[], uint32_t u32wLen)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Addr = 1u, u8Ctrl = 0u;
    uint32_t u32txLen = 0u;

    I2C_START(i2c);                                                         /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));               /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x18u:                                                      /* Slave Address ACK */
                I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u));    /* Write Hi byte address of register */
                break;
            case 0x20u:                                                      /* Slave Address NACK */
            case 0x30u:                                                      /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                if(u8Addr)
                {
                    I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu));       /* Write Lo byte address of register */
                    u8Addr = 0u;
                }
                else if((u32txLen < u32wLen) && (u8Addr == 0u))
                {
                    I2C_SET_DATA(i2c, au8Data[u32txLen++]);                           /* Write data to Register I2CDAT*/
                }
                else
                {
                    u8Ctrl = I2C_CTL_STO_SI;                              /* Clear SI and send STOP */
                    u8Xfering = 0u;
                }
                break;
            case 0x38u:                                                      /* Arbitration Lost */
            default:                                                        /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                                   /* Write controlbit to I2C_CTL register */
    }
    return u32txLen;                                                        /* Return bytes length that have been transmitted */
}

/**
  * @brief      Read a byte from Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  *
  * @return     Read a byte data from Slave
  *
  * @details    The function is used for I2C Master to read a byte data from Slave.
  *
  */
uint8_t I2C_ReadByte(I2C_T *i2c, uint8_t u8SlaveAddr)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, rdata = 0u, u8Ctrl = 0u;

    I2C_START(i2c);                                                /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u));    /* Write SLA+R to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x40u:                                             /* Slave Address ACK */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x48u:                                             /* Slave Address NACK */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x58u:
                rdata = (unsigned char) I2C_GET_DATA(i2c);         /* Receive Data */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                             /* Arbitration Lost */
            default:                                               /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                          /* Write controlbit to I2C_CTL register */
    }
    if(u8Err)
    {
        rdata = 0u;                                                 /* If occurs error, return 0 */
    }
    return rdata;                                                  /* Return read data */
}


/**
  * @brief      Read multi bytes from Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[out] au8Rdata[]         A data array to store data from Slave
  * @param[in]  u32rLen         How many bytes need to read from Slave
  *
  * @return     A length of how many bytes have been received
  *
  * @details    The function is used for I2C Master to read multi data bytes from Slave.
  *
  *
  */
uint32_t I2C_ReadMultiBytes(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t au8Rdata[], uint32_t u32rLen)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
    uint32_t u32rxLen = 0u;

    I2C_START(i2c);                                                /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u));    /* Write SLA+R to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x40u:                                             /* Slave Address ACK */
                u8Ctrl = I2C_CTL_SI_AA;                          /* Clear SI and set ACK */
                break;
            case 0x48u:                                             /* Slave Address NACK */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x50u:
                au8Rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c);    /* Receive Data */
                if(u32rxLen < (u32rLen - 1u))
                {
                    u8Ctrl = I2C_CTL_SI_AA;                             /* Clear SI and set ACK */
                }
                else
                {
                    u8Ctrl = I2C_CTL_SI;                                /* Clear SI */
                }
                break;
            case 0x58u:
                au8Rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c);    /* Receive Data */
                u8Ctrl = I2C_CTL_STO_SI;                                /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                                    /* Arbitration Lost */
            default:                                                      /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                                /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                                 /* Write controlbit to I2C_CTL register */
    }
    return u32rxLen;                                                      /* Return bytes length that have been received */
}


/**
  * @brief      Specify a byte register address and read a byte from Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u8DataAddr      Specify a address(1 byte) of data read from
  *
  * @return     Read a byte data from Slave
  *
  * @details    The function is used for I2C Master specify a byte address that a data byte read from Slave.
  *
  *
  */
uint8_t I2C_ReadByteOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Rdata = 0u, u8Ctrl = 0u;

    I2C_START(i2c);                                                /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));      /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x18u:                                             /* Slave Address ACK */
                I2C_SET_DATA(i2c, u8DataAddr);                     /* Write Lo byte address of register */
                break;
            case 0x20u:                                             /* Slave Address NACK */
            case 0x30u:                                             /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                u8Ctrl = I2C_CTL_STA_SI;                         /* Send repeat START */
                break;
            case 0x10u:
                I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u));    /* Write SLA+R to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                               /* Clear SI */
                break;
            case 0x40u:                                             /* Slave Address ACK */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x48u:                                             /* Slave Address NACK */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x58u:
                u8Rdata = (uint8_t) I2C_GET_DATA(i2c);               /* Receive Data */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                             /* Arbitration Lost */
            default:                                               /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                          /* Write controlbit to I2C_CTL register */
    }
    if(u8Err)
    {
        u8Rdata = 0u;                                                 /* If occurs error, return 0 */
    }
    return u8Rdata;                                                  /* Return read data */
}

/**
  * @brief      Specify a byte register address and read multi bytes from Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u8DataAddr      Specify a address (1 bytes) of data read from
  * @param[out] au8Rdata[]         A data array to store data from Slave
  * @param[in]  u32rLen         How many bytes need to read from Slave
  *
  * @return     A length of how many bytes have been received
  *
  * @details    The function is used for I2C Master specify a byte address that multi data bytes read from Slave.
  *
  *
  */
uint32_t I2C_ReadMultiBytesOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr, uint8_t au8Rdata[], uint32_t u32rLen)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
    uint32_t u32rxLen = 0u;

    I2C_START(i2c);                                                /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));      /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x18u:                                             /* Slave Address ACK */
                I2C_SET_DATA(i2c, u8DataAddr);                     /* Write Lo byte address of register */
                break;
            case 0x20u:                                             /* Slave Address NACK */
            case 0x30u:                                             /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                u8Ctrl = I2C_CTL_STA_SI;                         /* Send repeat START */
                break;
            case 0x10u:
                I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u));    /* Write SLA+R to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                             /* Clear SI */
                break;
            case 0x40u:                                             /* Slave Address ACK */
                u8Ctrl = I2C_CTL_SI_AA;                          /* Clear SI and set ACK */
                break;
            case 0x48u:                                             /* Slave Address NACK */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x50u:
                au8Rdata[u32rxLen++] = (uint8_t) I2C_GET_DATA(i2c);   /* Receive Data */
                if(u32rxLen < (u32rLen - 1u))
                {
                    u8Ctrl = I2C_CTL_SI_AA;                      /* Clear SI and set ACK */
                }
                else
                {
                    u8Ctrl = I2C_CTL_SI;                         /* Clear SI */
                }
                break;
            case 0x58u:
                au8Rdata[u32rxLen++] = (uint8_t) I2C_GET_DATA(i2c);   /* Receive Data */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                             /* Arbitration Lost */
            default:                                               /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                         /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                          /* Write controlbit to I2C_CTL register */
    }
    return u32rxLen;                                               /* Return bytes length that have been received */
}

/**
  * @brief      Specify two bytes register address and read a byte from Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u16DataAddr     Specify an address(2 bytes) of data read from
  *
  * @return     Read a byte data from Slave
  *
  * @details    The function is used for I2C Master specify two bytes address that a data byte read from Slave.
  *
  *
  */
uint8_t I2C_ReadByteTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Rdata = 0u, u8Addr = 1u, u8Ctrl = 0u;

    I2C_START(i2c);                                                         /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));               /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x18u:                                                      /* Slave Address ACK */
                I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u));    /* Write Hi byte address of register */
                break;
            case 0x20u:                                                      /* Slave Address NACK */
            case 0x30u:                                                      /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                if(u8Addr)
                {
                    I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu));       /* Write Lo byte address of register */
                    u8Addr = 0u;
                }
                else
                {
                    u8Ctrl = I2C_CTL_STA_SI;                              /* Clear SI and send repeat START */
                }
                break;
            case 0x10u:
                I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u));             /* Write SLA+R to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x40u:                                                      /* Slave Address ACK */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x48u:                                                      /* Slave Address NACK */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x58u:
                u8Rdata = (unsigned char) I2C_GET_DATA(i2c);                  /* Receive Data */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                                      /* Arbitration Lost */
            default:                                                        /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                                   /* Write controlbit to I2C_CTL register */
    }
    if(u8Err)
    {
        u8Rdata = 0u;                                                          /* If occurs error, return 0 */
    }
    return u8Rdata;                                                           /* Return read data */
}

/**
  * @brief      Specify two bytes register address and read multi bytes from Slave
  *
  * @param[in]  *i2c            Point to I2C peripheral
  * @param[in]  u8SlaveAddr     Access Slave address(7-bit)
  * @param[in]  u16DataAddr     Specify a address (2 bytes) of data read from
  * @param[out] au8Rdata[]         A data array to store data from Slave
  * @param[in]  u32rLen         How many bytes need to read from Slave
  *
  * @return     A length of how many bytes have been received
  *
  * @details    The function is used for I2C Master specify two bytes address that multi data bytes read from Slave.
  *
  *
  */
uint32_t I2C_ReadMultiBytesTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr, uint8_t au8Rdata[], uint32_t u32rLen)
{
    uint8_t u8Xfering = 1u, u8Err = 0u, u8Addr = 1u, u8Ctrl = 0u;
    uint32_t u32rxLen = 0u;

    I2C_START(i2c);                                                         /* Send START */
    while(u8Xfering && (u8Err == 0u))
    {
        I2C_WAIT_READY(i2c) {}
        switch(I2C_GET_STATUS(i2c))
        {
            case 0x08u:
                I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u));               /* Write SLA+W to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x18u:                                                      /* Slave Address ACK */
                I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u));    /* Write Hi byte address of register */
                break;
            case 0x20u:                                                      /* Slave Address NACK */
            case 0x30u:                                                      /* Master transmit data NACK */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x28u:
                if(u8Addr)
                {
                    I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu));       /* Write Lo byte address of register */
                    u8Addr = 0u;
                }
                else
                {
                    u8Ctrl = I2C_CTL_STA_SI;                              /* Clear SI and send repeat START */
                }
                break;
            case 0x10u:
                I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u));             /* Write SLA+R to Register I2CDAT */
                u8Ctrl = I2C_CTL_SI;                                      /* Clear SI */
                break;
            case 0x40u:                                                      /* Slave Address ACK */
                u8Ctrl = I2C_CTL_SI_AA;                                   /* Clear SI and set ACK */
                break;
            case 0x48u:                                                      /* Slave Address NACK */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
            case 0x50u:
                au8Rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c);      /* Receive Data */
                if(u32rxLen < (u32rLen - 1u))
                {
                    u8Ctrl = I2C_CTL_SI_AA;                               /* Clear SI and set ACK */
                }
                else
                {
                    u8Ctrl = I2C_CTL_SI;                                  /* Clear SI */
                }
                break;
            case 0x58u:
                au8Rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c);      /* Receive Data */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Xfering = 0u;
                break;
            case 0x38u:                                                      /* Arbitration Lost */
            default:                                                        /* Unknow status */
                u8Ctrl = I2C_CTL_STO_SI;                                  /* Clear SI and send STOP */
                u8Err = 1u;
                break;
        }
        I2C_SET_CONTROL_REG(i2c, u8Ctrl);                                   /* Write controlbit to I2C_CTL register */
    }
    return u32rxLen;                                                        /* Return bytes length that have been received */
}

/*@}*/ /* end of group I2C_EXPORTED_FUNCTIONS */

/*@}*/ /* end of group I2C_Driver */

/*@}*/ /* end of group Standard_Driver */

/*** (C) COPYRIGHT 2016 Nuvoton Technology Corp. ***/