/* --COPYRIGHT--,BSD
 * Copyright (c) 2014, Texas Instruments Incorporated
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * *  Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 * *  Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * *  Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
 * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * --/COPYRIGHT--*/
//*****************************************************************************
//
// eusci_a_spi.h - Driver for the EUSCI_A_SPI Module.
//
//*****************************************************************************

#ifndef __MSP430WARE_EUSCI_A_SPI_H__
#define __MSP430WARE_EUSCI_A_SPI_H__

#include "inc/hw_memmap.h"

#ifdef __MSP430_HAS_EUSCI_Ax__

//*****************************************************************************
//
// If building with a C++ compiler, make all of the definitions in this header
// have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif

#include "inc/hw_regaccess.h"
//*****************************************************************************
//
//! \brief Used in the EUSCI_A_SPI_changeMasterClock() function as the param
//! parameter.
//
//*****************************************************************************
typedef struct EUSCI_A_SPI_changeMasterClockParam
{
    //! Is the frequency of the selected clock source
    uint32_t clockSourceFrequency;
    //! Is the desired clock rate for SPI communication
    uint32_t desiredSpiClock;
} EUSCI_A_SPI_changeMasterClockParam;

//*****************************************************************************
//
//! \brief Used in the EUSCI_A_SPI_initSlave() function as the param parameter.
//
//*****************************************************************************
typedef struct EUSCI_A_SPI_initSlaveParam
{
    //! Controls the direction of the receive and transmit shift register.
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_MSB_FIRST
    //! - \b EUSCI_A_SPI_LSB_FIRST [Default]
    uint16_t msbFirst;
    //! Is clock phase select.
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_PHASE_DATA_CHANGED_ONFIRST_CAPTURED_ON_NEXT [Default]
    //! - \b EUSCI_A_SPI_PHASE_DATA_CAPTURED_ONFIRST_CHANGED_ON_NEXT
    uint16_t clockPhase;
    //! Is clock polarity select
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_HIGH
    //! - \b EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_LOW [Default]
    uint16_t clockPolarity;
    //! Is SPI mode select
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_3PIN
    //! - \b EUSCI_A_SPI_4PIN_UCxSTE_ACTIVE_HIGH
    //! - \b EUSCI_A_SPI_4PIN_UCxSTE_ACTIVE_LOW
    uint16_t spiMode;
} EUSCI_A_SPI_initSlaveParam;

//*****************************************************************************
//
//! \brief Used in the EUSCI_A_SPI_initMaster() function as the param
//! parameter.
//
//*****************************************************************************
typedef struct EUSCI_A_SPI_initMasterParam
{
    //! Selects Clock source.
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_CLOCKSOURCE_ACLK
    //! - \b EUSCI_A_SPI_CLOCKSOURCE_SMCLK
    uint8_t selectClockSource;
    //! Is the frequency of the selected clock source
    uint32_t clockSourceFrequency;
    //! Is the desired clock rate for SPI communication
    uint32_t desiredSpiClock;
    //! Controls the direction of the receive and transmit shift register.
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_MSB_FIRST
    //! - \b EUSCI_A_SPI_LSB_FIRST [Default]
    uint16_t msbFirst;
    //! Is clock phase select.
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_PHASE_DATA_CHANGED_ONFIRST_CAPTURED_ON_NEXT [Default]
    //! - \b EUSCI_A_SPI_PHASE_DATA_CAPTURED_ONFIRST_CHANGED_ON_NEXT
    uint16_t clockPhase;
    //! Is clock polarity select
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_HIGH
    //! - \b EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_LOW [Default]
    uint16_t clockPolarity;
    //! Is SPI mode select
    //! \n Valid values are:
    //! - \b EUSCI_A_SPI_3PIN
    //! - \b EUSCI_A_SPI_4PIN_UCxSTE_ACTIVE_HIGH
    //! - \b EUSCI_A_SPI_4PIN_UCxSTE_ACTIVE_LOW
    uint16_t spiMode;
} EUSCI_A_SPI_initMasterParam;

//*****************************************************************************
//
// The following are values that can be passed to the clockPhase parameter for
// functions: EUSCI_A_SPI_changeClockPhasePolarity(); the param parameter for
// functions: EUSCI_A_SPI_initMaster(), and EUSCI_A_SPI_initSlave().
//
//*****************************************************************************
#define EUSCI_A_SPI_PHASE_DATA_CHANGED_ONFIRST_CAPTURED_ON_NEXT            0x00
#define EUSCI_A_SPI_PHASE_DATA_CAPTURED_ONFIRST_CHANGED_ON_NEXT          UCCKPH

//*****************************************************************************
//
// The following are values that can be passed to the param parameter for
// functions: EUSCI_A_SPI_initMaster(), and EUSCI_A_SPI_initSlave().
//
//*****************************************************************************
#define EUSCI_A_SPI_MSB_FIRST                                             UCMSB
#define EUSCI_A_SPI_LSB_FIRST                                              0x00

//*****************************************************************************
//
// The following are values that can be passed to the param parameter for
// functions: EUSCI_A_SPI_initMaster(), and EUSCI_A_SPI_initSlave(); the
// clockPolarity parameter for functions:
// EUSCI_A_SPI_changeClockPhasePolarity().
//
//*****************************************************************************
#define EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_HIGH                        UCCKPL
#define EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_LOW                           0x00

//*****************************************************************************
//
// The following are values that can be passed to the param parameter for
// functions: EUSCI_A_SPI_initMaster().
//
//*****************************************************************************
#define EUSCI_A_SPI_CLOCKSOURCE_ACLK                               UCSSEL__ACLK
#define EUSCI_A_SPI_CLOCKSOURCE_SMCLK                             UCSSEL__SMCLK

//*****************************************************************************
//
// The following are values that can be passed to the param parameter for
// functions: EUSCI_A_SPI_initMaster(), and EUSCI_A_SPI_initSlave().
//
//*****************************************************************************
#define EUSCI_A_SPI_3PIN                                               UCMODE_0
#define EUSCI_A_SPI_4PIN_UCxSTE_ACTIVE_HIGH                            UCMODE_1
#define EUSCI_A_SPI_4PIN_UCxSTE_ACTIVE_LOW                             UCMODE_2

//*****************************************************************************
//
// The following are values that can be passed to the select4PinFunctionality
// parameter for functions: EUSCI_A_SPI_select4PinFunctionality().
//
//*****************************************************************************
#define EUSCI_A_SPI_PREVENT_CONFLICTS_WITH_OTHER_MASTERS                   0x00
#define EUSCI_A_SPI_ENABLE_SIGNAL_FOR_4WIRE_SLAVE                        UCSTEM

//*****************************************************************************
//
// The following are values that can be passed to the mask parameter for
// functions: EUSCI_A_SPI_enableInterrupt(), EUSCI_A_SPI_disableInterrupt(),
// EUSCI_A_SPI_getInterruptStatus(), and EUSCI_A_SPI_clearInterrupt() as well
// as returned by the EUSCI_A_SPI_getInterruptStatus() function.
//
//*****************************************************************************
#define EUSCI_A_SPI_TRANSMIT_INTERRUPT                                   UCTXIE
#define EUSCI_A_SPI_RECEIVE_INTERRUPT                                    UCRXIE

//*****************************************************************************
//
// The following are values that can be passed toThe following are values that
// can be returned by the EUSCI_A_SPI_isBusy() function.
//
//*****************************************************************************
#define EUSCI_A_SPI_BUSY                                                 UCBUSY
#define EUSCI_A_SPI_NOT_BUSY                                               0x00

//*****************************************************************************
//
// Prototypes for the APIs.
//
//*****************************************************************************

//*****************************************************************************
//
//! \brief Initializes the SPI Master block.
//!
//! Upon successful initialization of the SPI master block, this function will
//! have set the bus speed for the master, but the SPI Master block still
//! remains disabled and must be enabled with EUSCI_A_SPI_enable()
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI Master module.
//! \param param is the pointer to struct for master initialization.
//!
//! Modified bits are \b UCCKPH, \b UCCKPL, \b UC7BIT, \b UCMSB, \b UCSSELx and
//! \b UCSWRST of \b UCAxCTLW0 register.
//!
//! \return STATUS_SUCCESS
//
//*****************************************************************************
extern void EUSCI_A_SPI_initMaster(uint16_t baseAddress,
                                   EUSCI_A_SPI_initMasterParam *param);

//*****************************************************************************
//
//! \brief Selects 4Pin Functionality
//!
//! This function should be invoked only in 4-wire mode. Invoking this function
//! has no effect in 3-wire mode.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param select4PinFunctionality selects 4 pin functionality
//!        Valid values are:
//!        - \b EUSCI_A_SPI_PREVENT_CONFLICTS_WITH_OTHER_MASTERS
//!        - \b EUSCI_A_SPI_ENABLE_SIGNAL_FOR_4WIRE_SLAVE
//!
//! Modified bits are \b UCSTEM of \b UCAxCTLW0 register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_select4PinFunctionality(uint16_t baseAddress,
                                                uint8_t select4PinFunctionality);

//*****************************************************************************
//
//! \brief Initializes the SPI Master clock. At the end of this function call,
//! SPI module is left enabled.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param param is the pointer to struct for master clock setting.
//!
//! Modified bits are \b UCSWRST of \b UCAxCTLW0 register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_changeMasterClock(uint16_t baseAddress,
                                          EUSCI_A_SPI_changeMasterClockParam *param);

//*****************************************************************************
//
//! \brief Initializes the SPI Slave block.
//!
//! Upon successful initialization of the SPI slave block, this function will
//! have initialized the slave block, but the SPI Slave block still remains
//! disabled and must be enabled with EUSCI_A_SPI_enable()
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI Slave module.
//! \param param is the pointer to struct for slave initialization.
//!
//! Modified bits are \b UCMSB, \b UCMST, \b UC7BIT, \b UCCKPL, \b UCCKPH, \b
//! UCMODE and \b UCSWRST of \b UCAxCTLW0 register.
//!
//! \return STATUS_SUCCESS
//
//*****************************************************************************
extern void EUSCI_A_SPI_initSlave(uint16_t baseAddress,
                                  EUSCI_A_SPI_initSlaveParam *param);

//*****************************************************************************
//
//! \brief Changes the SPI clock phase and polarity. At the end of this
//! function call, SPI module is left enabled.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param clockPhase is clock phase select.
//!        Valid values are:
//!        - \b EUSCI_A_SPI_PHASE_DATA_CHANGED_ONFIRST_CAPTURED_ON_NEXT
//!           [Default]
//!        - \b EUSCI_A_SPI_PHASE_DATA_CAPTURED_ONFIRST_CHANGED_ON_NEXT
//! \param clockPolarity is clock polarity select
//!        Valid values are:
//!        - \b EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_HIGH
//!        - \b EUSCI_A_SPI_CLOCKPOLARITY_INACTIVITY_LOW [Default]
//!
//! Modified bits are \b UCCKPL, \b UCCKPH and \b UCSWRST of \b UCAxCTLW0
//! register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_changeClockPhasePolarity(uint16_t baseAddress,
                                                 uint16_t clockPhase,
                                                 uint16_t clockPolarity);

//*****************************************************************************
//
//! \brief Transmits a byte from the SPI Module.
//!
//! This function will place the supplied data into SPI transmit data register
//! to start transmission.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param transmitData data to be transmitted from the SPI module
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_transmitData(uint16_t baseAddress,
                                     uint8_t transmitData);

//*****************************************************************************
//
//! \brief Receives a byte that has been sent to the SPI Module.
//!
//! This function reads a byte of data from the SPI receive data Register.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//!
//! \return Returns the byte received from by the SPI module, cast as an
//!         uint8_t.
//
//*****************************************************************************
extern uint8_t EUSCI_A_SPI_receiveData(uint16_t baseAddress);

//*****************************************************************************
//
//! \brief Enables individual SPI interrupt sources.
//!
//! Enables the indicated SPI interrupt sources.  Only the sources that are
//! enabled can be reflected to the processor interrupt; disabled sources have
//! no effect on the processor. Does not clear interrupt flags.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param mask is the bit mask of the interrupt sources to be enabled.
//!        Mask value is the logical OR of any of the following:
//!        - \b EUSCI_A_SPI_TRANSMIT_INTERRUPT
//!        - \b EUSCI_A_SPI_RECEIVE_INTERRUPT
//!
//! Modified bits of \b UCAxIFG register and bits of \b UCAxIE register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_enableInterrupt(uint16_t baseAddress,
                                        uint8_t mask);

//*****************************************************************************
//
//! \brief Disables individual SPI interrupt sources.
//!
//! Disables the indicated SPI interrupt sources. Only the sources that are
//! enabled can be reflected to the processor interrupt; disabled sources have
//! no effect on the processor.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param mask is the bit mask of the interrupt sources to be disabled.
//!        Mask value is the logical OR of any of the following:
//!        - \b EUSCI_A_SPI_TRANSMIT_INTERRUPT
//!        - \b EUSCI_A_SPI_RECEIVE_INTERRUPT
//!
//! Modified bits of \b UCAxIE register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_disableInterrupt(uint16_t baseAddress,
                                         uint8_t mask);

//*****************************************************************************
//
//! \brief Gets the current SPI interrupt status.
//!
//! This returns the interrupt status for the SPI module based on which flag is
//! passed.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param mask is the masked interrupt flag status to be returned.
//!        Mask value is the logical OR of any of the following:
//!        - \b EUSCI_A_SPI_TRANSMIT_INTERRUPT
//!        - \b EUSCI_A_SPI_RECEIVE_INTERRUPT
//!
//! \return Logical OR of any of the following:
//!         - \b EUSCI_A_SPI_TRANSMIT_INTERRUPT
//!         - \b EUSCI_A_SPI_RECEIVE_INTERRUPT
//!         \n indicating the status of the masked interrupts
//
//*****************************************************************************
extern uint8_t EUSCI_A_SPI_getInterruptStatus(uint16_t baseAddress,
                                              uint8_t mask);

//*****************************************************************************
//
//! \brief Clears the selected SPI interrupt status flag.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//! \param mask is the masked interrupt flag to be cleared.
//!        Mask value is the logical OR of any of the following:
//!        - \b EUSCI_A_SPI_TRANSMIT_INTERRUPT
//!        - \b EUSCI_A_SPI_RECEIVE_INTERRUPT
//!
//! Modified bits of \b UCAxIFG register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_clearInterrupt(uint16_t baseAddress,
                                       uint8_t mask);

//*****************************************************************************
//
//! \brief Enables the SPI block.
//!
//! This will enable operation of the SPI block.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//!
//! Modified bits are \b UCSWRST of \b UCAxCTLW0 register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_enable(uint16_t baseAddress);

//*****************************************************************************
//
//! \brief Disables the SPI block.
//!
//! This will disable operation of the SPI block.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//!
//! Modified bits are \b UCSWRST of \b UCAxCTLW0 register.
//!
//! \return None
//
//*****************************************************************************
extern void EUSCI_A_SPI_disable(uint16_t baseAddress);

//*****************************************************************************
//
//! \brief Returns the address of the RX Buffer of the SPI for the DMA module.
//!
//! Returns the address of the SPI RX Buffer. This can be used in conjunction
//! with the DMA to store the received data directly to memory.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//!
//! \return the address of the RX Buffer
//
//*****************************************************************************
extern uint32_t EUSCI_A_SPI_getReceiveBufferAddress(uint16_t baseAddress);

//*****************************************************************************
//
//! \brief Returns the address of the TX Buffer of the SPI for the DMA module.
//!
//! Returns the address of the SPI TX Buffer. This can be used in conjunction
//! with the DMA to obtain transmitted data directly from memory.
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//!
//! \return the address of the TX Buffer
//
//*****************************************************************************
extern uint32_t EUSCI_A_SPI_getTransmitBufferAddress(uint16_t baseAddress);

//*****************************************************************************
//
//! \brief Indicates whether or not the SPI bus is busy.
//!
//! This function returns an indication of whether or not the SPI bus is
//! busy.This function checks the status of the bus via UCBBUSY bit
//!
//! \param baseAddress is the base address of the EUSCI_A_SPI module.
//!
//! \return One of the following:
//!         - \b EUSCI_A_SPI_BUSY
//!         - \b EUSCI_A_SPI_NOT_BUSY
//!         \n indicating if the EUSCI_A_SPI is busy
//
//*****************************************************************************
extern uint16_t EUSCI_A_SPI_isBusy(uint16_t baseAddress);

//*****************************************************************************
//
// Mark the end of the C bindings section for C++ compilers.
//
//*****************************************************************************
#ifdef __cplusplus
}
#endif

#endif
#endif // __MSP430WARE_EUSCI_A_SPI_H__