;;/*********************************************************************************************************************
;;* DISCLAIMER
;;* This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products.
;;* No other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all
;;* applicable laws, including copyright laws. 
;;* THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIESREGARDING THIS SOFTWARE, WHETHER EXPRESS, IMPLIED
;;* OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
;;* NON-INFRINGEMENT.  ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED.TO THE MAXIMUM EXTENT PERMITTED NOT PROHIBITED BY
;;* LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES SHALL BE LIABLE FOR ANY DIRECT,
;;* INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS SOFTWARE, EVEN IF RENESAS OR
;;* ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
;;* Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability 
;;* of this software. By using this software, you agree to the additional terms and conditions found by accessing the 
;;* following link:
;;* http://www.renesas.com/disclaimer
;;*
;;* Copyright (C) 2015 Renesas Electronics Corporation. All rights reserved.
;;*********************************************************************************************************************/
;;/*
;;**********************************************************************************************************************
;;* File Name    : r_cg_reset_program.asm
;;* Version      : Code Generator for RX231 V1.00.00.03 [10 Jul 2015]
;;* Device(s)    : R5F52318AxFP
;;* Tool-Chain   : GCCRX
;;* Description  : This is start up file for RX.
;;* Creation Date: 23/09/2015
;;**********************************************************************************************************************
;;*/

;;reset_program.asm

    .list
    .section .text
    .global _PowerON_Reset  ;;global Start routine

    .extern _HardwareSetup  ;;external Sub-routine to initialise Hardware
    .extern _data
    .extern _mdata
    .extern _ebss
    .extern _bss
    .extern _edata
    .extern _main
    .extern _ustack
    .extern _istack
    .extern _rvectors
    .extern _exit


_PowerON_Reset :
;;initialise user stack pointer
    mvtc    #_ustack,USP

;;initialise interrupt stack pointer
    mvtc    #_istack,ISP

#ifdef __RXv2__
;; setup exception vector
    mvtc    #_ExceptVectors, extb     ;;EXCEPTION VECTOR ADDRESS
#endif
;;setup intb
    mvtc    #_rvectors_start, intb    ;;INTERRUPT VECTOR ADDRESS  definition

;;setup FPSW
    mvtc    #100h, fpsw

;;load data section from ROM to RAM

    mov     #_mdata,r2      ;;src ROM address of data section in R2
    mov     #_data,r1       ;;dest start RAM address of data section in R1
    mov     #_edata,r3      ;;end RAM address of data section in R3
    sub     r1,r3           ;;size of data section in R3 (R3=R3-R1)
    smovf                   ;;block copy R3 bytes from R2 to R1

;;bss initialisation : zero out bss

    mov    #00h,r2          ;;load R2 reg with zero
    mov    #_ebss, r3       ;;store the end address of bss in R3
    mov    #_bss, r1        ;;store the start address of bss in R1
    sub    r1,r3            ;;ize of bss section in R3 (R3=R3-R1)
    sstr.b
;;call the hardware initialiser
    bsr.a    _HardwareSetup
    nop

;;setup PSW
    mvtc    #10000h, psw   ;;Set Ubit & Ibit for PSW

;;change PSW PM to user-mode
    MVFC   PSW,R1
;;DO NOT CHANGE TO USER MODE    OR     #00100000h,R1
    PUSH.L R1
    MVFC   PC,R1
    ADD    #10,R1
    PUSH.L R1
    RTE
    NOP
    NOP
#ifdef CPPAPP
    bsr.a    __rx_init
#endif
;;start user program
    bsr.a   _main
    bsr.a   _exit

#ifdef CPPAPP
    .global _rx_run_preinit_array
    .type   _rx_run_preinit_array,@function
_rx_run_preinit_array:
    mov     #__preinit_array_start,r1
    mov     #__preinit_array_end,r2
    bra.a   _rx_run_inilist

    .global _rx_run_init_array
    .type   _rx_run_init_array,@function
_rx_run_init_array:
    mov     #__init_array_start,r1
    mov     #__init_array_end,r2
    mov     #4, r3
    bra.a   _rx_run_inilist

    .global _rx_run_fini_array
    .type   _rx_run_fini_array,@function
_rx_run_fini_array:
    mov    #__fini_array_start,r2
    mov    #__fini_array_end,r1
    mov    #-4, r3
    ;;fall through

_rx_run_inilist:
next_inilist:
    cmp     r1,r2
    beq.b   done_inilist
    mov.l   [r1],r4
    cmp     #-1, r4
    beq.b   skip_inilist
    cmp     #0, r4
    beq.b   skip_inilist
    pushm   r1-r3
    jsr     r4
    popm    r1-r3
skip_inilist:
    add     r3,r1
    bra.b   next_inilist
done_inilist:
    rts

    .section    .init,"ax"
    .balign 4

    .global     __rx_init
__rx_init:

    .section    .fini,"ax"
    .balign 4

    .global     __rx_fini
__rx_fini:
    bsr.a   _rx_run_fini_array

    .section .sdata
    .balign 4
    .global __gp
    .weak   __gp
__gp:

    .section .data
    .global ___dso_handle
    .weak   ___dso_handle
___dso_handle:
    .long    0

     .section   .init,"ax"
     bsr.a      _rx_run_preinit_array
     bsr.a      _rx_run_init_array
     rts

    .global     __rx_init_end
__rx_init_end:

    .section    .fini,"ax"

    rts
    .global __rx_fini_end
__rx_fini_end:

#endif

;;call to exit
_exit:
    bra  _loop_here
_loop_here:
    bra _loop_here

    .text
    .end