/*
 * Handling of Ethernet PHY's
 * PHY's communicate with an EMAC either through
 * a Media-Independent Interface (MII), or a Reduced Media-Independent Interface (RMII).
 * The EMAC can poll for PHY ports on 32 different addresses. Each of the PHY ports
 * shall be treated independently.
 * 
 */

#ifndef PHYHANDLING_H

#define PHYHANDLING_H

#ifdef __cplusplus
extern "C" {
#endif


#ifndef ipconfigPHY_MAX_PORTS
	/* There can be at most 32 PHY ports, but in most cases there are 4 or less. */
	#define	ipconfigPHY_MAX_PORTS	4
#endif

/* A generic user-provided function that reads from the PHY-port at 'xAddress'( 0-based ). A 16-bit value shall be stored in
  '*pulValue'. xRegister is the register number ( 0 .. 31 ). In fact all PHY registers are 16-bit.
  Return non-zero in case the action failed. */
typedef BaseType_t ( *xApplicationPhyReadHook_t )( BaseType_t xAddress, BaseType_t xRegister, uint32_t *pulValue );

/* A generic user-provided function that writes 'ulValue' to the
   PHY-port at 'xAddress' ( 0-based ). xRegister is the register number ( 0 .. 31 ).
   Return non-zero in case the action failed. */
typedef BaseType_t ( *xApplicationPhyWriteHook_t )( BaseType_t xAddress, BaseType_t xRegister, uint32_t ulValue );

typedef struct xPhyProperties
{
	uint8_t ucSpeed;
	uint8_t ucMDI_X;		/* MDI-X : Medium Dependent Interface - Crossover */
	uint8_t ucDuplex;
	uint8_t ucSpare;
} PhyProperties_t;

typedef struct xEthernetPhy
{
	xApplicationPhyReadHook_t fnPhyRead;
	xApplicationPhyWriteHook_t fnPhyWrite;
	uint32_t ulPhyIDs[ ipconfigPHY_MAX_PORTS ];
	uint8_t ucPhyIndexes[ ipconfigPHY_MAX_PORTS ];
	TimeOut_t xLinkStatusTimer;
	TickType_t xLinkStatusRemaining;
	BaseType_t xPortCount;
	uint32_t ulBCRValue;
	uint32_t ulACRValue;
	uint32_t ulLinkStatusMask;
	PhyProperties_t xPhyPreferences;
	PhyProperties_t xPhyProperties;
} EthernetPhy_t;

/* Some defines used internally here to indicate preferences about speed, MDIX
(wired direct or crossed), and duplex (half or full). */

/* Values for PhyProperties_t::ucSpeed : */
#define	PHY_SPEED_10		1
#define	PHY_SPEED_100		2
#define	PHY_SPEED_AUTO		3

/* Values for PhyProperties_t::ucMDI_X : */
#define	PHY_MDIX_DIRECT		1
#define	PHY_MDIX_CROSSED	2
#define	PHY_MDIX_AUTO		3

/* Values for PhyProperties_t::ucDuplex : */
#define	PHY_DUPLEX_HALF		1
#define	PHY_DUPLEX_FULL		2
#define	PHY_DUPLEX_AUTO		3

/* ID's of supported PHY's : */
#define PHY_ID_LAN8742A		0x0007c130
#define PHY_ID_LAN8720		0x0007c0f0

#define PHY_ID_KSZ8041		0x000010A1
#define PHY_ID_KSZ8051		0x000010A1
#define PHY_ID_KSZ8081		0x000010A1

#define PHY_ID_KSZ8863		0x00221430
#define PHY_ID_KSZ8081MNXIA 0x00221560

#define PHY_ID_DP83848I		0x20005C90


/* Initialise the struct and assign a PHY-read and -write function. */
void vPhyInitialise( EthernetPhy_t *pxPhyObject, xApplicationPhyReadHook_t fnPhyRead, xApplicationPhyWriteHook_t fnPhyWrite );

/* Discover all PHY's connected by polling 32 indexes ( zero-based ) */
BaseType_t xPhyDiscover( EthernetPhy_t *pxPhyObject );

/* Send a reset command to the connected PHY ports and send configuration. */
BaseType_t xPhyConfigure( EthernetPhy_t *pxPhyObject, const PhyProperties_t *pxPhyProperties );

/* Give a command to start auto negotiation on a set of PHY port's. */
BaseType_t xPhyStartAutoNegotiation( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask );

/* Do not use auto negotiation but use predefined values from 'pxPhyObject->xPhyPreferences'. */
BaseType_t xPhyFixedValue( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask );

/* Check the current Link Status.
'xHadReception' : make this true if a packet has been received since the
last call to this function. */
BaseType_t xPhyCheckLinkStatus( EthernetPhy_t *pxPhyObject, BaseType_t xHadReception );

/* Get the bitmask of a given 'EthernetPhy_t'. */
#define xPhyGetMask( pxPhyObject ) \
	( ( ( ( uint32_t ) 1u ) << ( pxPhyObject )->xPortCount ) - 1u )

#ifdef __cplusplus
} /* extern "C" */
#endif

#endif