FreeRTOS/Demo/ARM9_AT91SAM9XE_IAR/ewp/at91sam9xe-ek-flash.mac

// ---------------------------------------------------------
//   ATMEL Microcontroller Software Support  -  ROUSSET  -
// ---------------------------------------------------------
// The software is delivered "AS IS" without warranty or
// condition of any  kind, either express, implied or
// statutory. This includes without limitation any warranty
// or condition with respect to merchantability or fitness
// for any particular purpose, or against the infringements of
// intellectual property rights of others.
// ---------------------------------------------------------
//  File: SAM9XE_FLASH.mac
//  User setup file for CSPY debugger.
//  1.1 08/Aug/06 jpp    : Creation
//
//  $Revision: 23594 $
//
// ---------------------------------------------------------
__var __mac_i;
__var __mac_pt;

/*********************************************************************
*
*       execUserReset() : JTAG set initially to Full Speed
*/
execUserReset()
{
    __message "------------------------------ execUserReset ---------------------------------";
    __writeMemory32(0x00000500, 0xFFFFFA00, "Memory"); // Set flash wait states
    __PllSetting();                        //* Init PLL
    __PllSetting100MHz();              
    __message "-------------------------------Set PC Reset ----------------------------------";
}

/*********************************************************************
*
*       execUserPreload() : JTAG set initially to 32kHz
*/
execUserPreload()
{
    __message "------------------------------ execUserPreload ---------------------------------";
    __hwReset(0);                          //* Hardware Reset: CPU is automatically halted after the reset (JTAG is already configured to 32kHz)
    __writeMemory32(0xD3,0x98,"Register"); //*  Set CPSR
    __writeMemory32(0x00000500, 0xFFFFFA00, "Memory"); // Set flash wait states
    __PllSetting();                        //* Init PLL
    __PllSetting100MHz();    
    _InitRSTC();                           //* Enable User Reset to allow execUserReset() execution
}



/*********************************************************************
*
*       _InitRSTC()
*
* Function description
*   Initializes the RSTC (Reset controller).
*   This makes sense since the default is to not allow user resets, which makes it impossible to
*   apply a second RESET via J-Link
*/
_InitRSTC() {
    __writeMemory32(0xA5000001, 0xFFFFFD08,"Memory");    // Allow user reset
}



/*********************************************************************
*
*       __PllSetting()
* Function description
*   Initializes the PMC.
*   1. Enable the Main Oscillator
*   2. Configure PLL
*   3. Switch Master
*/
__PllSetting()
{
     if ((__readMemory32(0xFFFFFC30,"Memory")&0x3) != 0 ) {
//* Disable all PMC interrupt ( $$ JPP)
//* AT91C_PMC_IDR   ((AT91_REG *) 0xFFFFFC64) //(PMC) Interrupt Disable Register
//*    pPmc->PMC_IDR = 0xFFFFFFFF;
    __writeMemory32(0xFFFFFFFF,0xFFFFFC64,"Memory");
//* AT91C_PMC_PCDR  ((AT91_REG *) 0xFFFFFC14) //(PMC) Peripheral Clock Disable Register
    __writeMemory32(0xFFFFFFFF,0xFFFFFC14,"Memory");
// Disable all clock only Processor clock is enabled.
    __writeMemory32(0xFFFFFFFE,0xFFFFFC04,"Memory");

// AT91C_PMC_MCKR  ((AT91_REG *) 	0xFFFFFC30) // (PMC) Master Clock Register
    __writeMemory32(0x00000001,0xFFFFFC30,"Memory");
    __sleep(10000);

// write reset value to PLLA and PLLB
// AT91C_PMC_PLLAR ((AT91_REG *) 	0xFFFFFC28) // (PMC) PLL A Register
    __writeMemory32(0x00003F00,0xFFFFFC28,"Memory");

// AT91C_PMC_PLLBR ((AT91_REG *) 	0xFFFFFC2C) // (PMC) PLL B Register
    __writeMemory32(0x00003F00,0xFFFFFC2C,"Memory");
    __sleep(10000);

   __message "------------------------------- PLL  Enable -----------------------------------------";
   } else {
   __message " ********* Core in SLOW CLOCK mode ********* "; }
}


/*********************************************************************
*
*       __PllSetting100MHz()
* Function description
*   Set core at 200 MHz and MCK at 100 MHz 
*/
__PllSetting100MHz()
{

   __message "------------------------------- PLL Set at 100 MHz ----------------------------------";

//* pPmc->PMC_MOR = (( AT91C_CKGR_OSCOUNT & (0x40 <<8) | AT91C_CKGR_MOSCEN ));
    __writeMemory32(0x00004001,0xFFFFFC20,"Memory");
    __sleep(10000);
// AT91C_PMC_MCKR  ((AT91_REG *) 	0xFFFFFC30) // (PMC) Master Clock Register
    __writeMemory32(0x00000001,0xFFFFFC30,"Memory");
    __sleep(10000);
//*   AT91C_BASE_CKGR->CKGR_PLLAR = (AT91C_CKGR_SRCA | ((96 << 16) & AT91C_CKGR_MULA) | 
//    (AT91C_CKGR_PLLACOUNT | (AT91C_CKGR_OUTA_0 | (9);
    __writeMemory32(0x2060BF09,0xFFFFFC28,"Memory");
    __sleep(10000);
//*   AT91C_BASE_PMC->PMC_MCKR =  AT91C_PMC_CSS_PLLA_CLK | AT91C_PMC_PRES_CLK | AT91C_PMC_MDIV_2;;
    __writeMemory32(0x00000102,0xFFFFFC30,"Memory");
     __sleep(10000);

}