/******************************************************************************
*
* Copyright (C) 2010 - 2016 Xilinx, Inc.  All rights reserved.
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* Use of the Software is limited solely to applications:
* (a) running on a Xilinx device, or
* (b) that interact with a Xilinx device through a bus or interconnect.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
* XILINX  BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
* OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
* SOFTWARE.
*
* Except as contained in this notice, the name of the Xilinx shall not be used
* in advertising or otherwise to promote the sale, use or other dealings in
* this Software without prior written authorization from Xilinx.
*
******************************************************************************/
/****************************************************************************/
/**
 *
 * @file xemacps.h
* @addtogroup emacps_v3_7
* @{
* @details
 *
 * The Xilinx Embedded Processor Block Ethernet driver.
 *
 * For a full description of XEMACPS features, please see the hardware spec.
 * This driver supports the following features:
 *   - Memory mapped access to host interface registers
 *   - Statistics counter registers for RMON/MIB
 *   - API for interrupt driven frame transfers for hardware configured DMA
 *   - Virtual memory support
 *   - Unicast, broadcast, and multicast receive address filtering
 *   - Full and half duplex operation
 *   - Automatic PAD & FCS insertion and stripping
 *   - Flow control
 *   - Support up to four 48bit addresses
 *   - Address checking for four specific 48bit addresses
 *   - VLAN frame support
 *   - Pause frame support
 *   - Large frame support up to 1536 bytes
 *   - Checksum offload
 *
 * <b>Driver Description</b>
 *
 * The device driver enables higher layer software (e.g., an application) to
 * communicate to the XEmacPs. The driver handles transmission and reception
 * of Ethernet frames, as well as configuration and control. No pre or post
 * processing of frame data is performed. The driver does not validate the
 * contents of an incoming frame in addition to what has already occurred in
 * hardware.
 * A single device driver can support multiple devices even when those devices
 * have significantly different configurations.
 *
 * <b>Initialization & Configuration</b>
 *
 * The XEmacPs_Config structure is used by the driver to configure itself.
 * This configuration structure is typically created by the tool-chain based
 * on hardware build properties.
 *
 * The driver instance can be initialized in
 *
 *   - XEmacPs_CfgInitialize(InstancePtr, CfgPtr, EffectiveAddress):  Uses a
 *     configuration structure provided by the caller. If running in a system
 *     with address translation, the provided virtual memory base address
 *     replaces the physical address present in the configuration structure.
 *
 * The device supports DMA only as current development plan. No FIFO mode is
 * supported. The driver expects to start the DMA channels and expects that
 * the user has set up the buffer descriptor lists.
 *
 * <b>Interrupts and Asynchronous Callbacks</b>
 *
 * The driver has no dependencies on the interrupt controller. When an
 * interrupt occurs, the handler will perform a small amount of
 * housekeeping work, determine the source of the interrupt, and call the
 * appropriate callback function. All callbacks are registered by the user
 * level application.
 *
 * <b>Virtual Memory</b>
 *
 * All virtual to physical memory mappings must occur prior to accessing the
 * driver API.
 *
 * For DMA transactions, user buffers supplied to the driver must be in terms
 * of their physical address.
 *
 * <b>DMA</b>
 *
 * The DMA engine uses buffer descriptors (BDs) to describe Ethernet frames.
 * These BDs are typically chained together into a list the hardware follows
 * when transferring data in and out of the packet buffers. Each BD describes
 * a memory region containing either a full or partial Ethernet packet.
 *
 * Interrupt coalescing is not suppoted from this built-in DMA engine.
 *
 * This API requires the user to understand how the DMA operates. The
 * following paragraphs provide some explanation, but the user is encouraged
 * to read documentation in xemacps_bdring.h as well as study example code
 * that accompanies this driver.
 *
 * The API is designed to get BDs to and from the DMA engine in the most
 * efficient means possible. The first step is to establish a  memory region
 * to contain all BDs for a specific channel. This is done with
 * XEmacPs_BdRingCreate(). This function sets up a BD ring that hardware will
 * follow as BDs are processed. The ring will consist of a user defined number
 * of BDs which will all be partially initialized. For example on the transmit
 * channel, the driver will initialize all BDs' so that they are configured
 * for transmit. The more fields that can be permanently setup at
 * initialization, then the fewer accesses will be needed to each BD while
 * the DMA engine is in operation resulting in better throughput and CPU
 * utilization. The best case initialization would require the user to set
 * only a frame buffer address and length prior to submitting the BD to the
 * engine.
 *
 * BDs move through the engine with the help of functions
 * XEmacPs_BdRingAlloc(), XEmacPs_BdRingToHw(), XEmacPs_BdRingFromHw(),
 * and XEmacPs_BdRingFree().
 * All these functions handle BDs that are in place. That is, there are no
 * copies of BDs kept anywhere and any BD the user interacts with is an actual
 * BD from the same ring hardware accesses.
 *
 * BDs in the ring go through a series of states as follows:
 *   1. Idle. The driver controls BDs in this state.
 *   2. The user has data to transfer. XEmacPs_BdRingAlloc() is called to
 *      reserve BD(s). Once allocated, the user may setup the BD(s) with
 *      frame buffer address, length, and other attributes. The user controls
 *      BDs in this state.
 *   3. The user submits BDs to the DMA engine with XEmacPs_BdRingToHw. BDs
 *      in this state are either waiting to be processed by hardware, are in
 *      process, or have been processed. The DMA engine controls BDs in this
 *      state.
 *   4. Processed BDs are retrieved with XEmacEpv_BdRingFromHw() by the
 *      user. Once retrieved, the user can examine each BD for the outcome of
 *      the DMA transfer. The user controls BDs in this state. After examining
 *      the BDs the user calls XEmacPs_BdRingFree() which places the BDs back
 *      into state 1.
 *
 * Each of the four BD accessor functions operate on a set of BDs. A set is
 * defined as a segment of the BD ring consisting of one or more BDs. The user
 * views the set as a pointer to the first BD along with the number of BDs for
 * that set. The set can be navigated by using macros XEmacPs_BdNext(). The
 * user must exercise extreme caution when changing BDs in a set as there is
 * nothing to prevent doing a mBdNext past the end of the set and modifying a
 * BD out of bounds.
 *
 * XEmacPs_BdRingAlloc() + XEmacPs_BdRingToHw(), as well as
 * XEmacPs_BdRingFromHw() + XEmacPs_BdRingFree() are designed to be used in
 * tandem. The same BD set retrieved with BdRingAlloc should be the same one
 * provided to hardware with BdRingToHw. Same goes with BdRingFromHw and
 * BdRIngFree.
 *
 * <b>Alignment & Data Cache Restrictions</b>
 *
 * Due to the design of the hardware, all RX buffers, BDs need to be 4-byte
 * aligned. Please reference xemacps_bd.h for cache related macros.
 *
 * DMA Tx:
 *
 *   - If frame buffers exist in cached memory, then they must be flushed
 *     prior to committing them to hardware.
 *
 * DMA Rx:
 *
 *   - If frame buffers exist in cached memory, then the cache must be
 *     invalidated for the memory region containing the frame prior to data
 *     access
 *
 * Both cache invalidate/flush are taken care of in driver code.
 *
 * <b>Buffer Copying</b>
 *
 * The driver is designed for a zero-copy buffer scheme. That is, the driver
 * will not copy buffers. This avoids potential throughput bottlenecks within
 * the driver. If byte copying is required, then the transfer will take longer
 * to complete.
 *
 * <b>Checksum Offloading</b>
 *
 * The Embedded Processor Block Ethernet can be configured to perform IP, TCP
 * and UDP checksum offloading in both receive and transmit directions.
 *
 * IP packets contain a 16-bit checksum field, which is the 16-bit 1s
 * complement of the 1s complement sum of all 16-bit words in the header.
 * TCP and UDP packets contain a 16-bit checksum field, which is the 16-bit
 * 1s complement of the 1s complement sum of all 16-bit words in the header,
 * the data and a conceptual pseudo header.
 *
 * To calculate these checksums in software requires each byte of the packet
 * to be read. For TCP and UDP this can use a large amount of processing power.
 * Offloading the checksum calculation to hardware can result in significant
 * performance improvements.
 *
 * The transmit checksum offload is only available to use DMA in packet buffer
 * mode. This is because the complete frame to be transmitted must be read
 * into the packet buffer memory before the checksum can be calculated and
 * written to the header at the beginning of the frame.
 *
 * For IP, TCP or UDP receive checksum offload to be useful, the operating
 * system containing the protocol stack must be aware that this offload is
 * available so that it can make use of the fact that the hardware has verified
 * the checksum.
 *
 * When receive checksum offloading is enabled in the hardware, the IP header
 * checksum is checked, where the packet meets the following criteria:
 *
 * 1. If present, the VLAN header must be four octets long and the CFI bit
 *    must not be set.
 * 2. Encapsulation must be RFC 894 Ethernet Type Encoding or RFC 1042 SNAP
 *    encoding.
 * 3. IP v4 packet.
 * 4. IP header is of a valid length.
 * 5. Good IP header checksum.
 * 6. No IP fragmentation.
 * 7. TCP or UDP packet.
 *
 * When an IP, TCP or UDP frame is received, the receive buffer descriptor
 * gives an indication if the hardware was able to verify the checksums.
 * There is also an indication if the frame had SNAP encapsulation. These
 * indication bits will replace the type ID match indication bits when the
 * receive checksum offload is enabled.
 *
 * If any of the checksums are verified incorrect by the hardware, the packet
 * is discarded and the appropriate statistics counter incremented.
 *
 * <b>PHY Interfaces</b>
 *
 * RGMII 1.3 is the only interface supported.
 *
 * <b>Asserts</b>
 *
 * Asserts are used within all Xilinx drivers to enforce constraints on
 * parameters. Asserts can be turned off on a system-wide basis by defining,
 * at compile time, the NDEBUG identifier. By default, asserts are turned on
 * and it is recommended that users leave asserts on during development. For
 * deployment use -DNDEBUG compiler switch to remove assert code.
 *
 * @note
 *
 * Xilinx drivers are typically composed of two parts, one is the driver
 * and the other is the adapter.  The driver is independent of OS and processor
 * and is intended to be highly portable.  The adapter is OS-specific and
 * facilitates communication between the driver and an OS.
 * This driver is intended to be RTOS and processor independent. Any needs for
 * dynamic memory management, threads or thread mutual exclusion, or cache
 * control must be satisfied bythe layer above this driver.
 *
 * <pre>
 * MODIFICATION HISTORY:
 *
 * Ver   Who  Date     Changes
 * ----- ---- -------- -------------------------------------------------------
 * 1.00a wsy  01/10/10 First release
 * 1.00a asa  11/21/11 The function XEmacPs_BdRingFromHwTx in file
 *		       xemacps_bdring.c is modified. Earlier it was checking for
 *		       "BdLimit"(passed argument) number of BDs for finding out
 *		       which BDs are successfully processed. Now one more check
 *		       is added. It looks for BDs till the current BD pointer
 *		       reaches HwTail. By doing this processing time is saved.
 * 1.00a asa  01/24/12 The function XEmacPs_BdRingFromHwTx in file
 *		       xemacps_bdring.c is modified. Now start of packet is
 *		       searched for returning the number of BDs processed.
 * 1.02a asa  11/05/12 Added a new API for deleting an entry from the HASH
 *		       registers. Added a new API to set the bust length.
 *		       Added some new hash-defines.
 * 1.03a asa  01/23/12 Fix for CR #692702 which updates error handling for
 *		       Rx errors. Under heavy Rx traffic, there will be a large
 *		       number of errors related to receive buffer not available.
 *		       Because of a HW bug (SI #692601), under such heavy errors,
 *		       the Rx data path can become unresponsive. To reduce the
 *		       probabilities for hitting this HW bug, the SW writes to
 *		       bit 18 to flush a packet from Rx DPRAM immediately. The
 *		       changes for it are done in the function
 *		       XEmacPs_IntrHandler.
 * 1.05a asa  09/23/13 Cache operations on BDs are not required and hence
 *		       removed. It is expected that all BDs are allocated in
 *		       from uncached area.
 * 1.06a asa  11/02/13 Changed the value for XEMACPS_RXBUF_LEN_MASK from 0x3fff
 *				to 0x1fff. This fixes the CR#744902.
 *			  Made changes in example file xemacps_example.h to fix compilation
 *			  issues with iarcc compiler.
 * 2.0   adk  10/12/13 Updated as per the New Tcl API's
 * 2.1   adk  11/08/14 Fixed the CR#811288. Changes are made in the driver tcl file.
 * 2.1   bss  09/08/14 Modified driver tcl to fix CR#820349 to export phy
 *		       address in xparameters.h when GMII to RGMII converter
 *		       is present in hw.
 * 2.1   srt  07/15/14 Add support for Zynq Ultrascale Mp GEM specification and 64-bit
 *		       changes.
 * 2.2   adk  29/10/14 Fixed CR#827686 when PCS/PMA core is configured with
 *                    1000BASE-X mode export proper values to the xparameters.h
 *                    file. Changes are made in the driver tcl file.
 * 3.0   adk  08/1/15  Don't include gem in peripheral test when gem is
 *                    configured with PCS/PMA Core. Changes are made in the
 *		       test app tcl(CR:827686).
 * 3.0   kvn  02/13/15 Modified code for MISRA-C:2012 compliance.
 * 3.0   hk   03/18/15 Added support for jumbo frames. Increase AHB burst.
 *                     Disable extended mode. Perform all 64 bit changes under
 *                     check for arch64.
 *                     Remove "used bit set" from TX error interrupt masks.
 * 3.1   hk   07/27/15 Do not call error handler with '0' error code when
 *                     there is no error. CR# 869403
 *            08/10/15 Update upper 32 bit tx and rx queue ptr registers.
 * 3.2   hk   02/22/16 Added SGMII support for Zynq Ultrascale+ MPSoC.
 * 3.4   ms   01/23/17 Modified xil_printf statement in main function for all
 *                     examples to ensure that "Successfully ran" and "Failed"
 *                     strings are available in all examples. This is a fix
 *                     for CR-965028.
 *       ms   03/17/17 Modified text file in examples folder for doxygen
 *                     generation.
 *       ms   04/05/17 Added tabspace for return statements in functions of
 *                     xemacps_ieee1588_example.c for proper documentation
 *                     while generating doxygen.
 * 3.5   hk   08/14/17 Update cache coherency information of the interface in
 *                     its config structure.
 * 3.6   rb   09/08/17 HwCnt variable (in XEmacPs_BdRing structure) is
 *		       changed to volatile.
 *		       Add API XEmacPs_BdRingPtrReset() to reset pointers
 *
 * </pre>
 *
 ****************************************************************************/

#ifndef XEMACPS_H		/* prevent circular inclusions */
#define XEMACPS_H		/* by using protection macros */

#ifdef __cplusplus
extern "C" {
#endif

/***************************** Include Files ********************************/

#include "xil_types.h"
#include "xil_assert.h"
#include "xstatus.h"
#include "xemacps_hw.h"
#include "xemacps_bd.h"
#include "xemacps_bdring.h"

/************************** Constant Definitions ****************************/

/*
 * Device information
 */
#define XEMACPS_DEVICE_NAME     "xemacps"
#define XEMACPS_DEVICE_DESC     "Xilinx PS 10/100/1000 MAC"


/** @name Configuration options
 *
 * Device configuration options. See the XEmacPs_SetOptions(),
 * XEmacPs_ClearOptions() and XEmacPs_GetOptions() for information on how to
 * use options.
 *
 * The default state of the options are noted and are what the device and
 * driver will be set to after calling XEmacPs_Reset() or
 * XEmacPs_Initialize().
 *
 * @{
 */

#define XEMACPS_PROMISC_OPTION               0x00000001U
/**< Accept all incoming packets.
 *   This option defaults to disabled (cleared) */

#define XEMACPS_FRAME1536_OPTION             0x00000002U
/**< Frame larger than 1516 support for Tx & Rx.
 *   This option defaults to disabled (cleared) */

#define XEMACPS_VLAN_OPTION                  0x00000004U
/**< VLAN Rx & Tx frame support.
 *   This option defaults to disabled (cleared) */

#define XEMACPS_FLOW_CONTROL_OPTION          0x00000010U
/**< Enable recognition of flow control frames on Rx
 *   This option defaults to enabled (set) */

#define XEMACPS_FCS_STRIP_OPTION             0x00000020U
/**< Strip FCS and PAD from incoming frames. Note: PAD from VLAN frames is not
 *   stripped.
 *   This option defaults to enabled (set) */

#define XEMACPS_FCS_INSERT_OPTION            0x00000040U
/**< Generate FCS field and add PAD automatically for outgoing frames.
 *   This option defaults to disabled (cleared) */

#define XEMACPS_LENTYPE_ERR_OPTION           0x00000080U
/**< Enable Length/Type error checking for incoming frames. When this option is
 *   set, the MAC will filter frames that have a mismatched type/length field
 *   and if XEMACPS_REPORT_RXERR_OPTION is set, the user is notified when these
 *   types of frames are encountered. When this option is cleared, the MAC will
 *   allow these types of frames to be received.
 *
 *   This option defaults to disabled (cleared) */

#define XEMACPS_TRANSMITTER_ENABLE_OPTION    0x00000100U
/**< Enable the transmitter.
 *   This option defaults to enabled (set) */

#define XEMACPS_RECEIVER_ENABLE_OPTION       0x00000200U
/**< Enable the receiver
 *   This option defaults to enabled (set) */

#define XEMACPS_BROADCAST_OPTION             0x00000400U
/**< Allow reception of the broadcast address
 *   This option defaults to enabled (set) */

#define XEMACPS_MULTICAST_OPTION             0x00000800U
/**< Allows reception of multicast addresses programmed into hash
 *   This option defaults to disabled (clear) */

#define XEMACPS_RX_CHKSUM_ENABLE_OPTION      0x00001000U
/**< Enable the RX checksum offload
 *   This option defaults to enabled (set) */

#define XEMACPS_TX_CHKSUM_ENABLE_OPTION      0x00002000U
/**< Enable the TX checksum offload
 *   This option defaults to enabled (set) */

#define XEMACPS_JUMBO_ENABLE_OPTION	0x00004000U
#define XEMACPS_SGMII_ENABLE_OPTION	0x00008000U

#define XEMACPS_DEFAULT_OPTIONS                     \
    ((u32)XEMACPS_FLOW_CONTROL_OPTION |                  \
     (u32)XEMACPS_FCS_INSERT_OPTION |                    \
     (u32)XEMACPS_FCS_STRIP_OPTION |                     \
     (u32)XEMACPS_BROADCAST_OPTION |                     \
     (u32)XEMACPS_LENTYPE_ERR_OPTION |                   \
     (u32)XEMACPS_TRANSMITTER_ENABLE_OPTION |            \
     (u32)XEMACPS_RECEIVER_ENABLE_OPTION |               \
     (u32)XEMACPS_RX_CHKSUM_ENABLE_OPTION |              \
     (u32)XEMACPS_TX_CHKSUM_ENABLE_OPTION)

/**< Default options set when device is initialized or reset */
/*@}*/

/** @name Callback identifiers
 *
 * These constants are used as parameters to XEmacPs_SetHandler()
 * @{
 */
#define XEMACPS_HANDLER_DMASEND 1U
#define XEMACPS_HANDLER_DMARECV 2U
#define XEMACPS_HANDLER_ERROR   3U
/*@}*/

/* Constants to determine the configuration of the hardware device. They are
 * used to allow the driver to verify it can operate with the hardware.
 */
#define XEMACPS_MDIO_DIV_DFT    MDC_DIV_32 /**< Default MDIO clock divisor */

/* The next few constants help upper layers determine the size of memory
 * pools used for Ethernet buffers and descriptor lists.
 */
#define XEMACPS_MAC_ADDR_SIZE   6U	/* size of Ethernet header */

#define XEMACPS_MTU             1500U	/* max MTU size of Ethernet frame */
#define XEMACPS_MTU_JUMBO       10240U	/* max MTU size of jumbo frame */
#define XEMACPS_HDR_SIZE        14U	/* size of Ethernet header */
#define XEMACPS_HDR_VLAN_SIZE   18U	/* size of Ethernet header with VLAN */
#define XEMACPS_TRL_SIZE        4U	/* size of Ethernet trailer (FCS) */
#define XEMACPS_MAX_FRAME_SIZE       (XEMACPS_MTU + XEMACPS_HDR_SIZE + \
        XEMACPS_TRL_SIZE)
#define XEMACPS_MAX_VLAN_FRAME_SIZE  (XEMACPS_MTU + XEMACPS_HDR_SIZE + \
        XEMACPS_HDR_VLAN_SIZE + XEMACPS_TRL_SIZE)
#define XEMACPS_MAX_VLAN_FRAME_SIZE_JUMBO  (XEMACPS_MTU_JUMBO + XEMACPS_HDR_SIZE + \
        XEMACPS_HDR_VLAN_SIZE + XEMACPS_TRL_SIZE)

/* DMACR Bust length hash defines */

#define XEMACPS_SINGLE_BURST	0x00000001
#define XEMACPS_4BYTE_BURST		0x00000004
#define XEMACPS_8BYTE_BURST		0x00000008
#define XEMACPS_16BYTE_BURST	0x00000010


/**************************** Type Definitions ******************************/
/** @name Typedefs for callback functions
 *
 * These callbacks are invoked in interrupt context.
 * @{
 */
/**
 * Callback invoked when frame(s) have been sent or received in interrupt
 * driven DMA mode. To set the send callback, invoke XEmacPs_SetHandler().
 *
 * @param CallBackRef is user data assigned when the callback was set.
 *
 * @note
 * See xemacps_hw.h for bitmasks definitions and the device hardware spec for
 * further information on their meaning.
 *
 */
typedef void (*XEmacPs_Handler) (void *CallBackRef);

/**
 * Callback when an asynchronous error occurs. To set this callback, invoke
 * XEmacPs_SetHandler() with XEMACPS_HANDLER_ERROR in the HandlerType
 * paramter.
 *
 * @param CallBackRef is user data assigned when the callback was set.
 * @param Direction defines either receive or transmit error(s) has occurred.
 * @param ErrorWord definition varies with Direction
 *
 */
typedef void (*XEmacPs_ErrHandler) (void *CallBackRef, u8 Direction,
				     u32 ErrorWord);

/*@}*/

/**
 * This typedef contains configuration information for a device.
 */
typedef struct {
	u16 DeviceId;	/**< Unique ID  of device */
	UINTPTR BaseAddress;/**< Physical base address of IPIF registers */
	u8 IsCacheCoherent; /**< Applicable only to A53 in EL1 mode;
				* describes whether Cache Coherent or not */
} XEmacPs_Config;


/**
 * The XEmacPs driver instance data. The user is required to allocate a
 * structure of this type for every XEmacPs device in the system. A pointer
 * to a structure of this type is then passed to the driver API functions.
 */
typedef struct XEmacPs_Instance {
	XEmacPs_Config Config;	/* Hardware configuration */
	u32 IsStarted;		/* Device is currently started */
	u32 IsReady;		/* Device is initialized and ready */
	u32 Options;		/* Current options word */

	XEmacPs_BdRing TxBdRing;	/* Transmit BD ring */
	XEmacPs_BdRing RxBdRing;	/* Receive BD ring */

	XEmacPs_Handler SendHandler;
	XEmacPs_Handler RecvHandler;
	void *SendRef;
	void *RecvRef;

	XEmacPs_ErrHandler ErrorHandler;
	void *ErrorRef;
	u32 Version;
	u32 RxBufMask;
	u32 MaxMtuSize;
	u32 MaxFrameSize;
	u32 MaxVlanFrameSize;

} XEmacPs;


/***************** Macros (Inline Functions) Definitions ********************/

/****************************************************************************/
/**
* Retrieve the Tx ring object. This object can be used in the various Ring
* API functions.
*
* @param  InstancePtr is the DMA channel to operate on.
*
* @return TxBdRing attribute
*
* @note
* C-style signature:
*    XEmacPs_BdRing XEmacPs_GetTxRing(XEmacPs *InstancePtr)
*
*****************************************************************************/
#define XEmacPs_GetTxRing(InstancePtr) ((InstancePtr)->TxBdRing)

/****************************************************************************/
/**
* Retrieve the Rx ring object. This object can be used in the various Ring
* API functions.
*
* @param  InstancePtr is the DMA channel to operate on.
*
* @return RxBdRing attribute
*
* @note
* C-style signature:
*    XEmacPs_BdRing XEmacPs_GetRxRing(XEmacPs *InstancePtr)
*
*****************************************************************************/
#define XEmacPs_GetRxRing(InstancePtr) ((InstancePtr)->RxBdRing)

/****************************************************************************/
/**
*
* Enable interrupts specified in <i>Mask</i>. The corresponding interrupt for
* each bit set to 1 in <i>Mask</i>, will be enabled.
*
* @param InstancePtr is a pointer to the instance to be worked on.
* @param Mask contains a bit mask of interrupts to enable. The mask can
*        be formed using a set of bitwise or'd values.
*
* @note
* The state of the transmitter and receiver are not modified by this function.
* C-style signature
*     void XEmacPs_IntEnable(XEmacPs *InstancePtr, u32 Mask)
*
*****************************************************************************/
#define XEmacPs_IntEnable(InstancePtr, Mask)                            \
	XEmacPs_WriteReg((InstancePtr)->Config.BaseAddress,             \
		XEMACPS_IER_OFFSET,                                     \
		((Mask) & XEMACPS_IXR_ALL_MASK));

/****************************************************************************/
/**
*
* Disable interrupts specified in <i>Mask</i>. The corresponding interrupt for
* each bit set to 1 in <i>Mask</i>, will be enabled.
*
* @param InstancePtr is a pointer to the instance to be worked on.
* @param Mask contains a bit mask of interrupts to disable. The mask can
*        be formed using a set of bitwise or'd values.
*
* @note
* The state of the transmitter and receiver are not modified by this function.
* C-style signature
*     void XEmacPs_IntDisable(XEmacPs *InstancePtr, u32 Mask)
*
*****************************************************************************/
#define XEmacPs_IntDisable(InstancePtr, Mask)                           \
	XEmacPs_WriteReg((InstancePtr)->Config.BaseAddress,             \
		XEMACPS_IDR_OFFSET,                                     \
		((Mask) & XEMACPS_IXR_ALL_MASK));

/****************************************************************************/
/**
*
* Enable interrupts specified in <i>Mask</i>. The corresponding interrupt for
* each bit set to 1 in <i>Mask</i>, will be enabled.
*
* @param InstancePtr is a pointer to the instance to be worked on.
* @param Mask contains a bit mask of interrupts to enable. The mask can
*        be formed using a set of bitwise or'd values.
*
* @note
* The state of the transmitter and receiver are not modified by this function.
* C-style signature
*     void XEmacPs_IntQ1Enable(XEmacPs *InstancePtr, u32 Mask)
*
*****************************************************************************/
#define XEmacPs_IntQ1Enable(InstancePtr, Mask)                            \
	XEmacPs_WriteReg((InstancePtr)->Config.BaseAddress,             \
		XEMACPS_INTQ1_IER_OFFSET,                                \
		((Mask) & XEMACPS_INTQ1_IXR_ALL_MASK));

/****************************************************************************/
/**
*
* Disable interrupts specified in <i>Mask</i>. The corresponding interrupt for
* each bit set to 1 in <i>Mask</i>, will be enabled.
*
* @param InstancePtr is a pointer to the instance to be worked on.
* @param Mask contains a bit mask of interrupts to disable. The mask can
*        be formed using a set of bitwise or'd values.
*
* @note
* The state of the transmitter and receiver are not modified by this function.
* C-style signature
*     void XEmacPs_IntDisable(XEmacPs *InstancePtr, u32 Mask)
*
*****************************************************************************/
#define XEmacPs_IntQ1Disable(InstancePtr, Mask)                           \
	XEmacPs_WriteReg((InstancePtr)->Config.BaseAddress,             \
		XEMACPS_INTQ1_IDR_OFFSET,                               \
		((Mask) & XEMACPS_INTQ1_IXR_ALL_MASK));

/****************************************************************************/
/**
*
* This macro triggers trasmit circuit to send data currently in TX buffer(s).
*
* @param InstancePtr is a pointer to the XEmacPs instance to be worked on.
*
* @return
*
* @note
*
* Signature: void XEmacPs_Transmit(XEmacPs *InstancePtr)
*
*****************************************************************************/
#define XEmacPs_Transmit(InstancePtr)                              \
        XEmacPs_WriteReg((InstancePtr)->Config.BaseAddress,          \
        XEMACPS_NWCTRL_OFFSET,                                     \
        (XEmacPs_ReadReg((InstancePtr)->Config.BaseAddress,          \
        XEMACPS_NWCTRL_OFFSET) | XEMACPS_NWCTRL_STARTTX_MASK))

/****************************************************************************/
/**
*
* This macro determines if the device is configured with checksum offloading
* on the receive channel
*
* @param InstancePtr is a pointer to the XEmacPs instance to be worked on.
*
* @return
*
* Boolean TRUE if the device is configured with checksum offloading, or
* FALSE otherwise.
*
* @note
*
* Signature: u32 XEmacPs_IsRxCsum(XEmacPs *InstancePtr)
*
*****************************************************************************/
#define XEmacPs_IsRxCsum(InstancePtr)                                     \
        ((XEmacPs_ReadReg((InstancePtr)->Config.BaseAddress,             \
          XEMACPS_NWCFG_OFFSET) & XEMACPS_NWCFG_RXCHKSUMEN_MASK) != 0U     \
          ? TRUE : FALSE)

/****************************************************************************/
/**
*
* This macro determines if the device is configured with checksum offloading
* on the transmit channel
*
* @param InstancePtr is a pointer to the XEmacPs instance to be worked on.
*
* @return
*
* Boolean TRUE if the device is configured with checksum offloading, or
* FALSE otherwise.
*
* @note
*
* Signature: u32 XEmacPs_IsTxCsum(XEmacPs *InstancePtr)
*
*****************************************************************************/
#define XEmacPs_IsTxCsum(InstancePtr)                                     \
        ((XEmacPs_ReadReg((InstancePtr)->Config.BaseAddress,              \
          XEMACPS_DMACR_OFFSET) & XEMACPS_DMACR_TCPCKSUM_MASK) != 0U       \
          ? TRUE : FALSE)

/************************** Function Prototypes *****************************/

/*
 * Initialization functions in xemacps.c
 */
LONG XEmacPs_CfgInitialize(XEmacPs *InstancePtr, XEmacPs_Config *CfgPtr,
			   UINTPTR EffectiveAddress);
void XEmacPs_Start(XEmacPs *InstancePtr);
void XEmacPs_Stop(XEmacPs *InstancePtr);
void XEmacPs_Reset(XEmacPs *InstancePtr);
void XEmacPs_SetQueuePtr(XEmacPs *InstancePtr, UINTPTR QPtr, u8 QueueNum,
			 u16 Direction);

/*
 * Lookup configuration in xemacps_sinit.c
 */
XEmacPs_Config *XEmacPs_LookupConfig(u16 DeviceId);

/*
 * Interrupt-related functions in xemacps_intr.c
 * DMA only and FIFO is not supported. This DMA does not support coalescing.
 */
LONG XEmacPs_SetHandler(XEmacPs *InstancePtr, u32 HandlerType,
			void *FuncPointer, void *CallBackRef);
void XEmacPs_IntrHandler(void *XEmacPsPtr);

/*
 * MAC configuration/control functions in XEmacPs_control.c
 */
LONG XEmacPs_SetOptions(XEmacPs *InstancePtr, u32 Options);
LONG XEmacPs_ClearOptions(XEmacPs *InstancePtr, u32 Options);
u32 XEmacPs_GetOptions(XEmacPs *InstancePtr);

LONG XEmacPs_SetMacAddress(XEmacPs *InstancePtr, void *AddressPtr, u8 Index);
LONG XEmacPs_DeleteHash(XEmacPs *InstancePtr, void *AddressPtr);
void XEmacPs_GetMacAddress(XEmacPs *InstancePtr, void *AddressPtr, u8 Index);

LONG XEmacPs_SetHash(XEmacPs *InstancePtr, void *AddressPtr);
void XEmacPs_ClearHash(XEmacPs *InstancePtr);
void XEmacPs_GetHash(XEmacPs *InstancePtr, void *AddressPtr);

void XEmacPs_SetMdioDivisor(XEmacPs *InstancePtr,
				XEmacPs_MdcDiv Divisor);
void XEmacPs_SetOperatingSpeed(XEmacPs *InstancePtr, u16 Speed);
u16 XEmacPs_GetOperatingSpeed(XEmacPs *InstancePtr);
LONG XEmacPs_PhyRead(XEmacPs *InstancePtr, u32 PhyAddress,
		     u32 RegisterNum, u16 *PhyDataPtr);
LONG XEmacPs_PhyWrite(XEmacPs *InstancePtr, u32 PhyAddress,
		      u32 RegisterNum, u16 PhyData);
LONG XEmacPs_SetTypeIdCheck(XEmacPs *InstancePtr, u32 Id_Check, u8 Index);

LONG XEmacPs_SendPausePacket(XEmacPs *InstancePtr);
void XEmacPs_DMABLengthUpdate(XEmacPs *InstancePtr, s32 BLength);

#ifdef __cplusplus
}
#endif

#endif /* end of protection macro */
/** @} */