#****************************************************************************
###
#
# @file psu_init.tcl
#
# This file is automatically generated
#
#****************************************************************************
set psu_pll_init_data {
		# : RPLL INIT
		# Register : RPLL_CFG @ 0XFF5E0034</p>

		# PLL loop filter resistor control
		# PSU_CRL_APB_RPLL_CFG_RES                                                        0xc

		# PLL charge pump control
		# PSU_CRL_APB_RPLL_CFG_CP                                                         0x3

		# PLL loop filter high frequency capacitor control
		# PSU_CRL_APB_RPLL_CFG_LFHF                                                       0x3

		# Lock circuit counter setting
		# PSU_CRL_APB_RPLL_CFG_LOCK_CNT                                                   0x339

		# Lock circuit configuration settings for lock windowsize
		# PSU_CRL_APB_RPLL_CFG_LOCK_DLY                                                   0x3f

		# Helper data. Values are to be looked up in a table from Data Sheet
		#(OFFSET, MASK, VALUE)      (0XFF5E0034, 0xFE7FEDEFU ,0x7E672C6CU)  */
    mask_write 0XFF5E0034 0xFE7FEDEF 0x7E672C6C
		# : UPDATE FB_DIV
		# Register : RPLL_CTRL @ 0XFF5E0030</p>

		# Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk i
    # s the source 100 video clk is the source 101 pss_alt_ref_clk is the sour
    # ce 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
		# PSU_CRL_APB_RPLL_CTRL_PRE_SRC                                                   0x0

		# The integer portion of the feedback divider to the PLL
		# PSU_CRL_APB_RPLL_CTRL_FBDIV                                                     0x2d

		# This turns on the divide by 2 that is inside of the PLL. This does not c
    # hange the VCO frequency, just the output frequency
		# PSU_CRL_APB_RPLL_CTRL_DIV2                                                      0x1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00717F00U ,0x00012D00U)  */
    mask_write 0XFF5E0030 0x00717F00 0x00012D00
		# : BY PASS PLL
		# Register : RPLL_CTRL @ 0XFF5E0030</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRL_APB_RPLL_CTRL_BYPASS                                                    1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF5E0030 0x00000008 0x00000008
		# : ASSERT RESET
		# Register : RPLL_CTRL @ 0XFF5E0030</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRL_APB_RPLL_CTRL_RESET                                                     1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF5E0030 0x00000001 0x00000001
		# : DEASSERT RESET
		# Register : RPLL_CTRL @ 0XFF5E0030</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRL_APB_RPLL_CTRL_RESET                                                     0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF5E0030 0x00000001 0x00000000
		# : CHECK PLL STATUS
		# Register : PLL_STATUS @ 0XFF5E0040</p>

		# RPLL is locked
		# PSU_CRL_APB_PLL_STATUS_RPLL_LOCK                                                1
    mask_poll 0XFF5E0040 0x00000002
		# : REMOVE PLL BY PASS
		# Register : RPLL_CTRL @ 0XFF5E0030</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRL_APB_RPLL_CTRL_BYPASS                                                    0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0030 0x00000008 0x00000000
		# Register : RPLL_TO_FPD_CTRL @ 0XFF5E0048</p>

		# Divisor value for this clock.
		# PSU_CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0                                           0x2

		# Control for a clock that will be generated in the LPD, but used in the F
    # PD as a clock source for the peripheral clock muxes.
		#(OFFSET, MASK, VALUE)      (0XFF5E0048, 0x00003F00U ,0x00000200U)  */
    mask_write 0XFF5E0048 0x00003F00 0x00000200
		# : RPLL FRAC CFG
		# : IOPLL INIT
		# Register : IOPLL_CFG @ 0XFF5E0024</p>

		# PLL loop filter resistor control
		# PSU_CRL_APB_IOPLL_CFG_RES                                                       0x2

		# PLL charge pump control
		# PSU_CRL_APB_IOPLL_CFG_CP                                                        0x4

		# PLL loop filter high frequency capacitor control
		# PSU_CRL_APB_IOPLL_CFG_LFHF                                                      0x3

		# Lock circuit counter setting
		# PSU_CRL_APB_IOPLL_CFG_LOCK_CNT                                                  0x258

		# Lock circuit configuration settings for lock windowsize
		# PSU_CRL_APB_IOPLL_CFG_LOCK_DLY                                                  0x3f

		# Helper data. Values are to be looked up in a table from Data Sheet
		#(OFFSET, MASK, VALUE)      (0XFF5E0024, 0xFE7FEDEFU ,0x7E4B0C82U)  */
    mask_write 0XFF5E0024 0xFE7FEDEF 0x7E4B0C82
		# : UPDATE FB_DIV
		# Register : IOPLL_CTRL @ 0XFF5E0020</p>

		# Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk i
    # s the source 100 video clk is the source 101 pss_alt_ref_clk is the sour
    # ce 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
		# PSU_CRL_APB_IOPLL_CTRL_PRE_SRC                                                  0x0

		# The integer portion of the feedback divider to the PLL
		# PSU_CRL_APB_IOPLL_CTRL_FBDIV                                                    0x5a

		# This turns on the divide by 2 that is inside of the PLL. This does not c
    # hange the VCO frequency, just the output frequency
		# PSU_CRL_APB_IOPLL_CTRL_DIV2                                                     0x1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00717F00U ,0x00015A00U)  */
    mask_write 0XFF5E0020 0x00717F00 0x00015A00
		# : BY PASS PLL
		# Register : IOPLL_CTRL @ 0XFF5E0020</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRL_APB_IOPLL_CTRL_BYPASS                                                   1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF5E0020 0x00000008 0x00000008
		# : ASSERT RESET
		# Register : IOPLL_CTRL @ 0XFF5E0020</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRL_APB_IOPLL_CTRL_RESET                                                    1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF5E0020 0x00000001 0x00000001
		# : DEASSERT RESET
		# Register : IOPLL_CTRL @ 0XFF5E0020</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRL_APB_IOPLL_CTRL_RESET                                                    0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF5E0020 0x00000001 0x00000000
		# : CHECK PLL STATUS
		# Register : PLL_STATUS @ 0XFF5E0040</p>

		# IOPLL is locked
		# PSU_CRL_APB_PLL_STATUS_IOPLL_LOCK                                               1
    mask_poll 0XFF5E0040 0x00000001
		# : REMOVE PLL BY PASS
		# Register : IOPLL_CTRL @ 0XFF5E0020</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRL_APB_IOPLL_CTRL_BYPASS                                                   0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0020 0x00000008 0x00000000
		# Register : IOPLL_TO_FPD_CTRL @ 0XFF5E0044</p>

		# Divisor value for this clock.
		# PSU_CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0                                          0x3

		# Control for a clock that will be generated in the LPD, but used in the F
    # PD as a clock source for the peripheral clock muxes.
		#(OFFSET, MASK, VALUE)      (0XFF5E0044, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFF5E0044 0x00003F00 0x00000300
		# : IOPLL FRAC CFG
		# : APU_PLL INIT
		# Register : APLL_CFG @ 0XFD1A0024</p>

		# PLL loop filter resistor control
		# PSU_CRF_APB_APLL_CFG_RES                                                        0x2

		# PLL charge pump control
		# PSU_CRF_APB_APLL_CFG_CP                                                         0x3

		# PLL loop filter high frequency capacitor control
		# PSU_CRF_APB_APLL_CFG_LFHF                                                       0x3

		# Lock circuit counter setting
		# PSU_CRF_APB_APLL_CFG_LOCK_CNT                                                   0x258

		# Lock circuit configuration settings for lock windowsize
		# PSU_CRF_APB_APLL_CFG_LOCK_DLY                                                   0x3f

		# Helper data. Values are to be looked up in a table from Data Sheet
		#(OFFSET, MASK, VALUE)      (0XFD1A0024, 0xFE7FEDEFU ,0x7E4B0C62U)  */
    mask_write 0XFD1A0024 0xFE7FEDEF 0x7E4B0C62
		# : UPDATE FB_DIV
		# Register : APLL_CTRL @ 0XFD1A0020</p>

		# Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk i
    # s the source 100 video clk is the source 101 pss_alt_ref_clk is the sour
    # ce 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
		# PSU_CRF_APB_APLL_CTRL_PRE_SRC                                                   0x0

		# The integer portion of the feedback divider to the PLL
		# PSU_CRF_APB_APLL_CTRL_FBDIV                                                     0x48

		# This turns on the divide by 2 that is inside of the PLL. This does not c
    # hange the VCO frequency, just the output frequency
		# PSU_CRF_APB_APLL_CTRL_DIV2                                                      0x1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00717F00U ,0x00014800U)  */
    mask_write 0XFD1A0020 0x00717F00 0x00014800
		# : BY PASS PLL
		# Register : APLL_CTRL @ 0XFD1A0020</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRF_APB_APLL_CTRL_BYPASS                                                    1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A0020 0x00000008 0x00000008
		# : ASSERT RESET
		# Register : APLL_CTRL @ 0XFD1A0020</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRF_APB_APLL_CTRL_RESET                                                     1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD1A0020 0x00000001 0x00000001
		# : DEASSERT RESET
		# Register : APLL_CTRL @ 0XFD1A0020</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRF_APB_APLL_CTRL_RESET                                                     0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD1A0020 0x00000001 0x00000000
		# : CHECK PLL STATUS
		# Register : PLL_STATUS @ 0XFD1A0044</p>

		# APLL is locked
		# PSU_CRF_APB_PLL_STATUS_APLL_LOCK                                                1
    mask_poll 0XFD1A0044 0x00000001
		# : REMOVE PLL BY PASS
		# Register : APLL_CTRL @ 0XFD1A0020</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRF_APB_APLL_CTRL_BYPASS                                                    0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A0020 0x00000008 0x00000000
		# Register : APLL_TO_LPD_CTRL @ 0XFD1A0048</p>

		# Divisor value for this clock.
		# PSU_CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0                                           0x3

		# Control for a clock that will be generated in the FPD, but used in the L
    # PD as a clock source for the peripheral clock muxes.
		#(OFFSET, MASK, VALUE)      (0XFD1A0048, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFD1A0048 0x00003F00 0x00000300
		# : APLL FRAC CFG
		# : DDR_PLL INIT
		# Register : DPLL_CFG @ 0XFD1A0030</p>

		# PLL loop filter resistor control
		# PSU_CRF_APB_DPLL_CFG_RES                                                        0x2

		# PLL charge pump control
		# PSU_CRF_APB_DPLL_CFG_CP                                                         0x3

		# PLL loop filter high frequency capacitor control
		# PSU_CRF_APB_DPLL_CFG_LFHF                                                       0x3

		# Lock circuit counter setting
		# PSU_CRF_APB_DPLL_CFG_LOCK_CNT                                                   0x258

		# Lock circuit configuration settings for lock windowsize
		# PSU_CRF_APB_DPLL_CFG_LOCK_DLY                                                   0x3f

		# Helper data. Values are to be looked up in a table from Data Sheet
		#(OFFSET, MASK, VALUE)      (0XFD1A0030, 0xFE7FEDEFU ,0x7E4B0C62U)  */
    mask_write 0XFD1A0030 0xFE7FEDEF 0x7E4B0C62
		# : UPDATE FB_DIV
		# Register : DPLL_CTRL @ 0XFD1A002C</p>

		# Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk i
    # s the source 100 video clk is the source 101 pss_alt_ref_clk is the sour
    # ce 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
		# PSU_CRF_APB_DPLL_CTRL_PRE_SRC                                                   0x0

		# The integer portion of the feedback divider to the PLL
		# PSU_CRF_APB_DPLL_CTRL_FBDIV                                                     0x40

		# This turns on the divide by 2 that is inside of the PLL. This does not c
    # hange the VCO frequency, just the output frequency
		# PSU_CRF_APB_DPLL_CTRL_DIV2                                                      0x1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00717F00U ,0x00014000U)  */
    mask_write 0XFD1A002C 0x00717F00 0x00014000
		# : BY PASS PLL
		# Register : DPLL_CTRL @ 0XFD1A002C</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRF_APB_DPLL_CTRL_BYPASS                                                    1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A002C 0x00000008 0x00000008
		# : ASSERT RESET
		# Register : DPLL_CTRL @ 0XFD1A002C</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRF_APB_DPLL_CTRL_RESET                                                     1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD1A002C 0x00000001 0x00000001
		# : DEASSERT RESET
		# Register : DPLL_CTRL @ 0XFD1A002C</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRF_APB_DPLL_CTRL_RESET                                                     0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD1A002C 0x00000001 0x00000000
		# : CHECK PLL STATUS
		# Register : PLL_STATUS @ 0XFD1A0044</p>

		# DPLL is locked
		# PSU_CRF_APB_PLL_STATUS_DPLL_LOCK                                                1
    mask_poll 0XFD1A0044 0x00000002
		# : REMOVE PLL BY PASS
		# Register : DPLL_CTRL @ 0XFD1A002C</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRF_APB_DPLL_CTRL_BYPASS                                                    0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A002C 0x00000008 0x00000000
		# Register : DPLL_TO_LPD_CTRL @ 0XFD1A004C</p>

		# Divisor value for this clock.
		# PSU_CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0                                           0x2

		# Control for a clock that will be generated in the FPD, but used in the L
    # PD as a clock source for the peripheral clock muxes.
		#(OFFSET, MASK, VALUE)      (0XFD1A004C, 0x00003F00U ,0x00000200U)  */
    mask_write 0XFD1A004C 0x00003F00 0x00000200
		# : DPLL FRAC CFG
		# : VIDEO_PLL INIT
		# Register : VPLL_CFG @ 0XFD1A003C</p>

		# PLL loop filter resistor control
		# PSU_CRF_APB_VPLL_CFG_RES                                                        0x2

		# PLL charge pump control
		# PSU_CRF_APB_VPLL_CFG_CP                                                         0x4

		# PLL loop filter high frequency capacitor control
		# PSU_CRF_APB_VPLL_CFG_LFHF                                                       0x3

		# Lock circuit counter setting
		# PSU_CRF_APB_VPLL_CFG_LOCK_CNT                                                   0x258

		# Lock circuit configuration settings for lock windowsize
		# PSU_CRF_APB_VPLL_CFG_LOCK_DLY                                                   0x3f

		# Helper data. Values are to be looked up in a table from Data Sheet
		#(OFFSET, MASK, VALUE)      (0XFD1A003C, 0xFE7FEDEFU ,0x7E4B0C82U)  */
    mask_write 0XFD1A003C 0xFE7FEDEF 0x7E4B0C82
		# : UPDATE FB_DIV
		# Register : VPLL_CTRL @ 0XFD1A0038</p>

		# Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk i
    # s the source 100 video clk is the source 101 pss_alt_ref_clk is the sour
    # ce 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
		# PSU_CRF_APB_VPLL_CTRL_PRE_SRC                                                   0x0

		# The integer portion of the feedback divider to the PLL
		# PSU_CRF_APB_VPLL_CTRL_FBDIV                                                     0x5a

		# This turns on the divide by 2 that is inside of the PLL. This does not c
    # hange the VCO frequency, just the output frequency
		# PSU_CRF_APB_VPLL_CTRL_DIV2                                                      0x1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00717F00U ,0x00015A00U)  */
    mask_write 0XFD1A0038 0x00717F00 0x00015A00
		# : BY PASS PLL
		# Register : VPLL_CTRL @ 0XFD1A0038</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRF_APB_VPLL_CTRL_BYPASS                                                    1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A0038 0x00000008 0x00000008
		# : ASSERT RESET
		# Register : VPLL_CTRL @ 0XFD1A0038</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRF_APB_VPLL_CTRL_RESET                                                     1

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD1A0038 0x00000001 0x00000001
		# : DEASSERT RESET
		# Register : VPLL_CTRL @ 0XFD1A0038</p>

		# Asserts Reset to the PLL. When asserting reset, the PLL must already be
    # in BYPASS.
		# PSU_CRF_APB_VPLL_CTRL_RESET                                                     0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD1A0038 0x00000001 0x00000000
		# : CHECK PLL STATUS
		# Register : PLL_STATUS @ 0XFD1A0044</p>

		# VPLL is locked
		# PSU_CRF_APB_PLL_STATUS_VPLL_LOCK                                                1
    mask_poll 0XFD1A0044 0x00000004
		# : REMOVE PLL BY PASS
		# Register : VPLL_CTRL @ 0XFD1A0038</p>

		# Bypasses the PLL clock. The usable clock will be determined from the POS
    # T_SRC field. (This signal may only be toggled after 4 cycles of the old
    # clock and 4 cycles of the new clock. This is not usually an issue, but d
    # esigners must be aware.)
		# PSU_CRF_APB_VPLL_CTRL_BYPASS                                                    0

		# PLL Basic Control
		#(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A0038 0x00000008 0x00000000
		# Register : VPLL_TO_LPD_CTRL @ 0XFD1A0050</p>

		# Divisor value for this clock.
		# PSU_CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0                                           0x3

		# Control for a clock that will be generated in the FPD, but used in the L
    # PD as a clock source for the peripheral clock muxes.
		#(OFFSET, MASK, VALUE)      (0XFD1A0050, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFD1A0050 0x00003F00 0x00000300
		# : VIDEO FRAC CFG
}

set psu_clock_init_data {
		# : CLOCK CONTROL SLCR REGISTER
		# Register : GEM3_REF_CTRL @ 0XFF5E005C</p>

		# Clock active for the RX channel
		# PSU_CRL_APB_GEM3_REF_CTRL_RX_CLKACT                                             0x1

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_GEM3_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRL_APB_GEM3_REF_CTRL_DIVISOR1                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_GEM3_REF_CTRL_DIVISOR0                                              0xc

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_GEM3_REF_CTRL_SRCSEL                                                0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E005C, 0x063F3F07U ,0x06010C00U)  */
    mask_write 0XFF5E005C 0x063F3F07 0x06010C00
		# Register : GEM_TSU_REF_CTRL @ 0XFF5E0100</p>

		# 6 bit divider
		# PSU_CRL_APB_GEM_TSU_REF_CTRL_DIVISOR0                                           0x6

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_GEM_TSU_REF_CTRL_SRCSEL                                             0x0

		# 6 bit divider
		# PSU_CRL_APB_GEM_TSU_REF_CTRL_DIVISOR1                                           0x1

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_GEM_TSU_REF_CTRL_CLKACT                                             0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0100, 0x013F3F07U ,0x01010600U)  */
    mask_write 0XFF5E0100 0x013F3F07 0x01010600
		# Register : USB0_BUS_REF_CTRL @ 0XFF5E0060</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_USB0_BUS_REF_CTRL_CLKACT                                            0x1

		# 6 bit divider
		# PSU_CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1                                          0x1

		# 6 bit divider
		# PSU_CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0                                          0x6

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_USB0_BUS_REF_CTRL_SRCSEL                                            0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0060, 0x023F3F07U ,0x02010600U)  */
    mask_write 0XFF5E0060 0x023F3F07 0x02010600
		# Register : USB3_DUAL_REF_CTRL @ 0XFF5E004C</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_USB3_DUAL_REF_CTRL_CLKACT                                           0x1

		# 6 bit divider
		# PSU_CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1                                         0x3

		# 6 bit divider
		# PSU_CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0                                         0x19

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL. (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL                                           0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E004C, 0x023F3F07U ,0x02031900U)  */
    mask_write 0XFF5E004C 0x023F3F07 0x02031900
		# Register : QSPI_REF_CTRL @ 0XFF5E0068</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_QSPI_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRL_APB_QSPI_REF_CTRL_DIVISOR1                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_QSPI_REF_CTRL_DIVISOR0                                              0xc

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_QSPI_REF_CTRL_SRCSEL                                                0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0068, 0x013F3F07U ,0x01010C00U)  */
    mask_write 0XFF5E0068 0x013F3F07 0x01010C00
		# Register : SDIO1_REF_CTRL @ 0XFF5E0070</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_SDIO1_REF_CTRL_CLKACT                                               0x1

		# 6 bit divider
		# PSU_CRL_APB_SDIO1_REF_CTRL_DIVISOR1                                             0x1

		# 6 bit divider
		# PSU_CRL_APB_SDIO1_REF_CTRL_DIVISOR0                                             0x8

		# 000 = IOPLL; 010 = RPLL; 011 = VPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_SDIO1_REF_CTRL_SRCSEL                                               0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0070, 0x013F3F07U ,0x01010800U)  */
    mask_write 0XFF5E0070 0x013F3F07 0x01010800
		# Register : SDIO_CLK_CTRL @ 0XFF18030C</p>

		# MIO pad selection for sdio1_rx_clk (feedback clock from the PAD) 0: MIO
    # [51] 1: MIO [76]
		# PSU_IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL                                     0

		# SoC Debug Clock Control
		#(OFFSET, MASK, VALUE)      (0XFF18030C, 0x00020000U ,0x00000000U)  */
    mask_write 0XFF18030C 0x00020000 0x00000000
		# Register : UART0_REF_CTRL @ 0XFF5E0074</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_UART0_REF_CTRL_CLKACT                                               0x1

		# 6 bit divider
		# PSU_CRL_APB_UART0_REF_CTRL_DIVISOR1                                             0x1

		# 6 bit divider
		# PSU_CRL_APB_UART0_REF_CTRL_DIVISOR0                                             0xf

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_UART0_REF_CTRL_SRCSEL                                               0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0074, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0074 0x013F3F07 0x01010F00
		# Register : UART1_REF_CTRL @ 0XFF5E0078</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_UART1_REF_CTRL_CLKACT                                               0x1

		# 6 bit divider
		# PSU_CRL_APB_UART1_REF_CTRL_DIVISOR1                                             0x1

		# 6 bit divider
		# PSU_CRL_APB_UART1_REF_CTRL_DIVISOR0                                             0xf

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_UART1_REF_CTRL_SRCSEL                                               0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0078, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0078 0x013F3F07 0x01010F00
		# Register : I2C0_REF_CTRL @ 0XFF5E0120</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_I2C0_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRL_APB_I2C0_REF_CTRL_DIVISOR1                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_I2C0_REF_CTRL_DIVISOR0                                              0xf

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_I2C0_REF_CTRL_SRCSEL                                                0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0120, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0120 0x013F3F07 0x01010F00
		# Register : I2C1_REF_CTRL @ 0XFF5E0124</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_I2C1_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRL_APB_I2C1_REF_CTRL_DIVISOR1                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_I2C1_REF_CTRL_DIVISOR0                                              0xf

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_I2C1_REF_CTRL_SRCSEL                                                0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0124, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0124 0x013F3F07 0x01010F00
		# Register : CAN1_REF_CTRL @ 0XFF5E0088</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_CAN1_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRL_APB_CAN1_REF_CTRL_DIVISOR1                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_CAN1_REF_CTRL_DIVISOR0                                              0xf

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_CAN1_REF_CTRL_SRCSEL                                                0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0088, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0088 0x013F3F07 0x01010F00
		# Register : CPU_R5_CTRL @ 0XFF5E0090</p>

		# Turing this off will shut down the OCM, some parts of the APM, and preve
    # nt transactions going from the FPD to the LPD and could lead to system h
    # ang
		# PSU_CRL_APB_CPU_R5_CTRL_CLKACT                                                  0x1

		# 6 bit divider
		# PSU_CRL_APB_CPU_R5_CTRL_DIVISOR0                                                0x3

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_CPU_R5_CTRL_SRCSEL                                                  0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0090, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E0090 0x01003F07 0x01000302
		# Register : IOU_SWITCH_CTRL @ 0XFF5E009C</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_IOU_SWITCH_CTRL_CLKACT                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_IOU_SWITCH_CTRL_DIVISOR0                                            0x6

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_IOU_SWITCH_CTRL_SRCSEL                                              0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E009C, 0x01003F07U ,0x01000602U)  */
    mask_write 0XFF5E009C 0x01003F07 0x01000602
		# Register : PCAP_CTRL @ 0XFF5E00A4</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_PCAP_CTRL_CLKACT                                                    0x1

		# 6 bit divider
		# PSU_CRL_APB_PCAP_CTRL_DIVISOR0                                                  0x8

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_PCAP_CTRL_SRCSEL                                                    0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E00A4, 0x01003F07U ,0x01000800U)  */
    mask_write 0XFF5E00A4 0x01003F07 0x01000800
		# Register : LPD_SWITCH_CTRL @ 0XFF5E00A8</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_LPD_SWITCH_CTRL_CLKACT                                              0x1

		# 6 bit divider
		# PSU_CRL_APB_LPD_SWITCH_CTRL_DIVISOR0                                            0x3

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_LPD_SWITCH_CTRL_SRCSEL                                              0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E00A8, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E00A8 0x01003F07 0x01000302
		# Register : LPD_LSBUS_CTRL @ 0XFF5E00AC</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_LPD_LSBUS_CTRL_CLKACT                                               0x1

		# 6 bit divider
		# PSU_CRL_APB_LPD_LSBUS_CTRL_DIVISOR0                                             0xf

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_LPD_LSBUS_CTRL_SRCSEL                                               0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E00AC, 0x01003F07U ,0x01000F02U)  */
    mask_write 0XFF5E00AC 0x01003F07 0x01000F02
		# Register : DBG_LPD_CTRL @ 0XFF5E00B0</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_DBG_LPD_CTRL_CLKACT                                                 0x1

		# 6 bit divider
		# PSU_CRL_APB_DBG_LPD_CTRL_DIVISOR0                                               0x6

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_DBG_LPD_CTRL_SRCSEL                                                 0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E00B0, 0x01003F07U ,0x01000602U)  */
    mask_write 0XFF5E00B0 0x01003F07 0x01000602
		# Register : ADMA_REF_CTRL @ 0XFF5E00B8</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_ADMA_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRL_APB_ADMA_REF_CTRL_DIVISOR0                                              0x3

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_ADMA_REF_CTRL_SRCSEL                                                0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E00B8, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E00B8 0x01003F07 0x01000302
		# Register : PL0_REF_CTRL @ 0XFF5E00C0</p>

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_PL0_REF_CTRL_CLKACT                                                 0x1

		# 6 bit divider
		# PSU_CRL_APB_PL0_REF_CTRL_DIVISOR1                                               0x1

		# 6 bit divider
		# PSU_CRL_APB_PL0_REF_CTRL_DIVISOR0                                               0xf

		# 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_PL0_REF_CTRL_SRCSEL                                                 0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E00C0, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E00C0 0x013F3F07 0x01010F00
		# Register : AMS_REF_CTRL @ 0XFF5E0108</p>

		# 6 bit divider
		# PSU_CRL_APB_AMS_REF_CTRL_DIVISOR1                                               0x1

		# 6 bit divider
		# PSU_CRL_APB_AMS_REF_CTRL_DIVISOR0                                               0x1e

		# 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled af
    # ter 4 cycles of the old clock and 4 cycles of the new clock. This is not
    #  usually an issue, but designers must be aware.)
		# PSU_CRL_APB_AMS_REF_CTRL_SRCSEL                                                 0x2

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_AMS_REF_CTRL_CLKACT                                                 0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0108, 0x013F3F07U ,0x01011E02U)  */
    mask_write 0XFF5E0108 0x013F3F07 0x01011E02
		# Register : DLL_REF_CTRL @ 0XFF5E0104</p>

		# 000 = IOPLL; 001 = RPLL; (This signal may only be toggled after 4 cycles
    #  of the old clock and 4 cycles of the new clock. This is not usually an
    # issue, but designers must be aware.)
		# PSU_CRL_APB_DLL_REF_CTRL_SRCSEL                                                 0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0104, 0x00000007U ,0x00000000U)  */
    mask_write 0XFF5E0104 0x00000007 0x00000000
		# Register : TIMESTAMP_REF_CTRL @ 0XFF5E0128</p>

		# 6 bit divider
		# PSU_CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0                                         0xf

		# 1XX = pss_ref_clk; 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may
    #  only be toggled after 4 cycles of the old clock and 4 cycles of the new
    #  clock. This is not usually an issue, but designers must be aware.)
		# PSU_CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL                                           0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRL_APB_TIMESTAMP_REF_CTRL_CLKACT                                           0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFF5E0128, 0x01003F07U ,0x01000F00U)  */
    mask_write 0XFF5E0128 0x01003F07 0x01000F00
		# Register : SATA_REF_CTRL @ 0XFD1A00A0</p>

		# 000 = IOPLL_TO_FPD; 010 = APLL; 011 = DPLL; (This signal may only be tog
    # gled after 4 cycles of the old clock and 4 cycles of the new clock. This
    #  is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_SATA_REF_CTRL_SRCSEL                                                0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_SATA_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRF_APB_SATA_REF_CTRL_DIVISOR0                                              0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00A0, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00A0 0x01003F07 0x01000200
		# Register : PCIE_REF_CTRL @ 0XFD1A00B4</p>

		# 000 = IOPLL_TO_FPD; 010 = RPLL_TO_FPD; 011 = DPLL; (This signal may only
    #  be toggled after 4 cycles of the old clock and 4 cycles of the new cloc
    # k. This is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_PCIE_REF_CTRL_SRCSEL                                                0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_PCIE_REF_CTRL_CLKACT                                                0x1

		# 6 bit divider
		# PSU_CRF_APB_PCIE_REF_CTRL_DIVISOR0                                              0x2

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00B4, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00B4 0x01003F07 0x01000200
		# Register : DP_VIDEO_REF_CTRL @ 0XFD1A0070</p>

		# 6 bit divider
		# PSU_CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1                                          0x1

		# 6 bit divider
		# PSU_CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0                                          0x5

		# 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (T
    # his signal may only be toggled after 4 cycles of the old clock and 4 cyc
    # les of the new clock. This is not usually an issue, but designers must b
    # e aware.)
		# PSU_CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL                                            0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_DP_VIDEO_REF_CTRL_CLKACT                                            0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A0070, 0x013F3F07U ,0x01010500U)  */
    mask_write 0XFD1A0070 0x013F3F07 0x01010500
		# Register : DP_AUDIO_REF_CTRL @ 0XFD1A0074</p>

		# 6 bit divider
		# PSU_CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1                                          0x1

		# 6 bit divider
		# PSU_CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0                                          0xf

		# 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (T
    # his signal may only be toggled after 4 cycles of the old clock and 4 cyc
    # les of the new clock. This is not usually an issue, but designers must b
    # e aware.)
		# PSU_CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL                                            0x3

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_DP_AUDIO_REF_CTRL_CLKACT                                            0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A0074, 0x013F3F07U ,0x01010F03U)  */
    mask_write 0XFD1A0074 0x013F3F07 0x01010F03
		# Register : DP_STC_REF_CTRL @ 0XFD1A007C</p>

		# 6 bit divider
		# PSU_CRF_APB_DP_STC_REF_CTRL_DIVISOR1                                            0x1

		# 6 bit divider
		# PSU_CRF_APB_DP_STC_REF_CTRL_DIVISOR0                                            0xe

		# 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD; (This signal may only be togg
    # led after 4 cycles of the old clock and 4 cycles of the new clock. This
    # is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_DP_STC_REF_CTRL_SRCSEL                                              0x3

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_DP_STC_REF_CTRL_CLKACT                                              0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A007C, 0x013F3F07U ,0x01010E03U)  */
    mask_write 0XFD1A007C 0x013F3F07 0x01010E03
		# Register : ACPU_CTRL @ 0XFD1A0060</p>

		# 6 bit divider
		# PSU_CRF_APB_ACPU_CTRL_DIVISOR0                                                  0x1

		# 000 = APLL; 010 = DPLL; 011 = VPLL; (This signal may only be toggled aft
    # er 4 cycles of the old clock and 4 cycles of the new clock. This is not
    # usually an issue, but designers must be aware.)
		# PSU_CRF_APB_ACPU_CTRL_SRCSEL                                                    0x0

		# Clock active signal. Switch to 0 to disable the clock. For the half spee
    # d APU Clock
		# PSU_CRF_APB_ACPU_CTRL_CLKACT_HALF                                               0x1

		# Clock active signal. Switch to 0 to disable the clock. For the full spee
    # d ACPUX Clock. This will shut off the high speed clock to the entire APU
		# PSU_CRF_APB_ACPU_CTRL_CLKACT_FULL                                               0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A0060, 0x03003F07U ,0x03000100U)  */
    mask_write 0XFD1A0060 0x03003F07 0x03000100
		# Register : DBG_FPD_CTRL @ 0XFD1A0068</p>

		# 6 bit divider
		# PSU_CRF_APB_DBG_FPD_CTRL_DIVISOR0                                               0x2

		# 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be tog
    # gled after 4 cycles of the old clock and 4 cycles of the new clock. This
    #  is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_DBG_FPD_CTRL_SRCSEL                                                 0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_DBG_FPD_CTRL_CLKACT                                                 0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A0068, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A0068 0x01003F07 0x01000200
		# Register : DDR_CTRL @ 0XFD1A0080</p>

		# 6 bit divider
		# PSU_CRF_APB_DDR_CTRL_DIVISOR0                                                   0x2

		# 000 = DPLL; 001 = VPLL; (This signal may only be toggled after 4 cycles
    # of the old clock and 4 cycles of the new clock. This is not usually an i
    # ssue, but designers must be aware.)
		# PSU_CRF_APB_DDR_CTRL_SRCSEL                                                     0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A0080, 0x00003F07U ,0x00000200U)  */
    mask_write 0XFD1A0080 0x00003F07 0x00000200
		# Register : GPU_REF_CTRL @ 0XFD1A0084</p>

		# 6 bit divider
		# PSU_CRF_APB_GPU_REF_CTRL_DIVISOR0                                               0x1

		# 000 = IOPLL_TO_FPD; 010 = VPLL; 011 = DPLL; (This signal may only be tog
    # gled after 4 cycles of the old clock and 4 cycles of the new clock. This
    #  is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_GPU_REF_CTRL_SRCSEL                                                 0x0

		# Clock active signal. Switch to 0 to disable the clock, which will stop c
    # lock for GPU (and both Pixel Processors).
		# PSU_CRF_APB_GPU_REF_CTRL_CLKACT                                                 0x1

		# Clock active signal for Pixel Processor. Switch to 0 to disable the cloc
    # k only to this Pixel Processor
		# PSU_CRF_APB_GPU_REF_CTRL_PP0_CLKACT                                             0x1

		# Clock active signal for Pixel Processor. Switch to 0 to disable the cloc
    # k only to this Pixel Processor
		# PSU_CRF_APB_GPU_REF_CTRL_PP1_CLKACT                                             0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A0084, 0x07003F07U ,0x07000100U)  */
    mask_write 0XFD1A0084 0x07003F07 0x07000100
		# Register : GDMA_REF_CTRL @ 0XFD1A00B8</p>

		# 6 bit divider
		# PSU_CRF_APB_GDMA_REF_CTRL_DIVISOR0                                              0x2

		# 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled aft
    # er 4 cycles of the old clock and 4 cycles of the new clock. This is not
    # usually an issue, but designers must be aware.)
		# PSU_CRF_APB_GDMA_REF_CTRL_SRCSEL                                                0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_GDMA_REF_CTRL_CLKACT                                                0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00B8, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00B8 0x01003F07 0x01000200
		# Register : DPDMA_REF_CTRL @ 0XFD1A00BC</p>

		# 6 bit divider
		# PSU_CRF_APB_DPDMA_REF_CTRL_DIVISOR0                                             0x2

		# 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled aft
    # er 4 cycles of the old clock and 4 cycles of the new clock. This is not
    # usually an issue, but designers must be aware.)
		# PSU_CRF_APB_DPDMA_REF_CTRL_SRCSEL                                               0x0

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_DPDMA_REF_CTRL_CLKACT                                               0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00BC, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00BC 0x01003F07 0x01000200
		# Register : TOPSW_MAIN_CTRL @ 0XFD1A00C0</p>

		# 6 bit divider
		# PSU_CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0                                            0x2

		# 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled aft
    # er 4 cycles of the old clock and 4 cycles of the new clock. This is not
    # usually an issue, but designers must be aware.)
		# PSU_CRF_APB_TOPSW_MAIN_CTRL_SRCSEL                                              0x3

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_TOPSW_MAIN_CTRL_CLKACT                                              0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00C0, 0x01003F07U ,0x01000203U)  */
    mask_write 0XFD1A00C0 0x01003F07 0x01000203
		# Register : TOPSW_LSBUS_CTRL @ 0XFD1A00C4</p>

		# 6 bit divider
		# PSU_CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0                                           0x5

		# 000 = APLL; 010 = IOPLL_TO_FPD; 011 = DPLL; (This signal may only be tog
    # gled after 4 cycles of the old clock and 4 cycles of the new clock. This
    #  is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL                                             0x2

		# Clock active signal. Switch to 0 to disable the clock
		# PSU_CRF_APB_TOPSW_LSBUS_CTRL_CLKACT                                             0x1

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00C4, 0x01003F07U ,0x01000502U)  */
    mask_write 0XFD1A00C4 0x01003F07 0x01000502
		# Register : DBG_TSTMP_CTRL @ 0XFD1A00F8</p>

		# 6 bit divider
		# PSU_CRF_APB_DBG_TSTMP_CTRL_DIVISOR0                                             0x2

		# 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be tog
    # gled after 4 cycles of the old clock and 4 cycles of the new clock. This
    #  is not usually an issue, but designers must be aware.)
		# PSU_CRF_APB_DBG_TSTMP_CTRL_SRCSEL                                               0x0

		# This register controls this reference clock
		#(OFFSET, MASK, VALUE)      (0XFD1A00F8, 0x00003F07U ,0x00000200U)  */
    mask_write 0XFD1A00F8 0x00003F07 0x00000200
		# Register : IOU_TTC_APB_CLK @ 0XFF180380</p>

		# 00" = Select the APB switch clock for the APB interface of TTC0'01" = Se
    # lect the PLL ref clock for the APB interface of TTC0'10" = Select the R5
    #  clock for the APB interface of TTC0
		# PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL                                           0

		# 00" = Select the APB switch clock for the APB interface of TTC1'01" = Se
    # lect the PLL ref clock for the APB interface of TTC1'10" = Select the R5
    #  clock for the APB interface of TTC1
		# PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL                                           0

		# 00" = Select the APB switch clock for the APB interface of TTC2'01" = Se
    # lect the PLL ref clock for the APB interface of TTC2'10" = Select the R5
    #  clock for the APB interface of TTC2
		# PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL                                           0

		# 00" = Select the APB switch clock for the APB interface of TTC3'01" = Se
    # lect the PLL ref clock for the APB interface of TTC3'10" = Select the R5
    #  clock for the APB interface of TTC3
		# PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL                                           0

		# TTC APB clock select
		#(OFFSET, MASK, VALUE)      (0XFF180380, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFF180380 0x000000FF 0x00000000
		# Register : WDT_CLK_SEL @ 0XFD610100</p>

		# System watchdog timer clock source selection: 0: Internal APB clock 1: E
    # xternal (PL clock via EMIO or Pinout clock via MIO)
		# PSU_FPD_SLCR_WDT_CLK_SEL_SELECT                                                 0

		# SWDT clock source select
		#(OFFSET, MASK, VALUE)      (0XFD610100, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD610100 0x00000001 0x00000000
		# Register : WDT_CLK_SEL @ 0XFF180300</p>

		# System watchdog timer clock source selection: 0: internal clock APB cloc
    # k 1: external clock from PL via EMIO, or from pinout via MIO
		# PSU_IOU_SLCR_WDT_CLK_SEL_SELECT                                                 0

		# SWDT clock source select
		#(OFFSET, MASK, VALUE)      (0XFF180300, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF180300 0x00000001 0x00000000
		# Register : CSUPMU_WDT_CLK_SEL @ 0XFF410050</p>

		# System watchdog timer clock source selection: 0: internal clock APB cloc
    # k 1: external clock pss_ref_clk
		# PSU_LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT                                          0

		# SWDT clock source select
		#(OFFSET, MASK, VALUE)      (0XFF410050, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF410050 0x00000001 0x00000000
}

set psu_ddr_init_data {
		# : DDR INITIALIZATION
		# : DDR CONTROLLER RESET
		# Register : RST_DDR_SS @ 0XFD1A0108</p>

		# DDR block level reset inside of the DDR Sub System
		# PSU_CRF_APB_RST_DDR_SS_DDR_RESET                                                0X1

		# DDR sub system block level reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0108, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A0108 0x00000008 0x00000008
		# Register : MSTR @ 0XFD070000</p>

		# Indicates the configuration of the device used in the system. - 00 - x4
    # device - 01 - x8 device - 10 - x16 device - 11 - x32 device
		# PSU_DDRC_MSTR_DEVICE_CONFIG                                                     0x1

		# Choose which registers are used. - 0 - Original registers - 1 - Shadow r
    # egisters
		# PSU_DDRC_MSTR_FREQUENCY_MODE                                                    0x0

		# Only present for multi-rank configurations. Each bit represents one rank
    # . For two-rank configurations, only bits[25:24] are present. - 1 - popul
    # ated - 0 - unpopulated LSB is the lowest rank number. For 2 ranks follow
    # ing combinations are legal: - 01 - One rank - 11 - Two ranks - Others -
    # Reserved. For 4 ranks following combinations are legal: - 0001 - One ran
    # k - 0011 - Two ranks - 1111 - Four ranks
		# PSU_DDRC_MSTR_ACTIVE_RANKS                                                      0x1

		# SDRAM burst length used: - 0001 - Burst length of 2 (only supported for
    # mDDR) - 0010 - Burst length of 4 - 0100 - Burst length of 8 - 1000 - Bur
    # st length of 16 (only supported for mDDR, LPDDR2, and LPDDR4) All other
    # values are reserved. This controls the burst size used to access the SDR
    # AM. This must match the burst length mode register setting in the SDRAM.
    #  (For BC4/8 on-the-fly mode of DDR3 and DDR4, set this field to 0x0100)
    # Burst length of 2 is not supported with AXI ports when MEMC_BURST_LENGTH
    #  is 8. Burst length of 2 is only supported with MEMC_FREQ_RATIO = 1
		# PSU_DDRC_MSTR_BURST_RDWR                                                        0x4

		# Set to 1 when the uMCTL2 and DRAM has to be put in DLL-off mode for low
    # frequency operation. Set to 0 to put uMCTL2 and DRAM in DLL-on mode for
    # normal frequency operation. If DDR4 CRC/parity retry is enabled (CRCPARC
    # TL1.crc_parity_retry_enable = 1), dll_off_mode is not supported, and thi
    # s bit must be set to '0'.
		# PSU_DDRC_MSTR_DLL_OFF_MODE                                                      0x0

		# Selects proportion of DQ bus width that is used by the SDRAM - 00 - Full
    #  DQ bus width to SDRAM - 01 - Half DQ bus width to SDRAM - 10 - Quarter
    # DQ bus width to SDRAM - 11 - Reserved. Note that half bus width mode is
    # only supported when the SDRAM bus width is a multiple of 16, and quarter
    #  bus width mode is only supported when the SDRAM bus width is a multiple
    #  of 32 and the configuration parameter MEMC_QBUS_SUPPORT is set. Bus wid
    # th refers to DQ bus width (excluding any ECC width).
		# PSU_DDRC_MSTR_DATA_BUS_WIDTH                                                    0x0

		# 1 indicates put the DRAM in geardown mode (2N) and 0 indicates put the D
    # RAM in normal mode (1N). This register can be changed, only when the Con
    # troller is in self-refresh mode. This signal must be set the same value
    # as MR3 bit A3. Note: Geardown mode is not supported if the configuration
    #  parameter MEMC_CMD_RTN2IDLE is set
		# PSU_DDRC_MSTR_GEARDOWN_MODE                                                     0x0

		# If 1, then uMCTL2 uses 2T timing. Otherwise, uses 1T timing. In 2T timin
    # g, all command signals (except chip select) are held for 2 clocks on the
    #  SDRAM bus. Chip select is asserted on the second cycle of the command N
    # ote: 2T timing is not supported in LPDDR2/LPDDR3/LPDDR4 mode Note: 2T ti
    # ming is not supported if the configuration parameter MEMC_CMD_RTN2IDLE i
    # s set Note: 2T timing is not supported in DDR4 geardown mode.
		# PSU_DDRC_MSTR_EN_2T_TIMING_MODE                                                 0x0

		# When set, enable burst-chop in DDR3/DDR4. Burst Chop for Reads is exerci
    # sed only in HIF configurations (UMCTL2_INCL_ARB not set) and if in full
    # bus width mode (MSTR.data_bus_width = 00). Burst Chop for Writes is exer
    # cised only if Partial Writes enabled (UMCTL2_PARTIAL_WR=1) and if CRC is
    #  disabled (CRCPARCTL1.crc_enable = 0). If DDR4 CRC/parity retry is enabl
    # ed (CRCPARCTL1.crc_parity_retry_enable = 1), burst chop is not supported
    # , and this bit must be set to '0'
		# PSU_DDRC_MSTR_BURSTCHOP                                                         0x0

		# Select LPDDR4 SDRAM - 1 - LPDDR4 SDRAM device in use. - 0 - non-LPDDR4 d
    # evice in use Present only in designs configured to support LPDDR4.
		# PSU_DDRC_MSTR_LPDDR4                                                            0x0

		# Select DDR4 SDRAM - 1 - DDR4 SDRAM device in use. - 0 - non-DDR4 device
    # in use Present only in designs configured to support DDR4.
		# PSU_DDRC_MSTR_DDR4                                                              0x1

		# Select LPDDR3 SDRAM - 1 - LPDDR3 SDRAM device in use. - 0 - non-LPDDR3 d
    # evice in use Present only in designs configured to support LPDDR3.
		# PSU_DDRC_MSTR_LPDDR3                                                            0x0

		# Select LPDDR2 SDRAM - 1 - LPDDR2 SDRAM device in use. - 0 - non-LPDDR2 d
    # evice in use Present only in designs configured to support LPDDR2.
		# PSU_DDRC_MSTR_LPDDR2                                                            0x0

		# Select DDR3 SDRAM - 1 - DDR3 SDRAM device in use - 0 - non-DDR3 SDRAM de
    # vice in use Only present in designs that support DDR3.
		# PSU_DDRC_MSTR_DDR3                                                              0x0

		# Master Register
		#(OFFSET, MASK, VALUE)      (0XFD070000, 0xE30FBE3DU ,0x41040010U)  */
    mask_write 0XFD070000 0xE30FBE3D 0x41040010
		# Register : MRCTRL0 @ 0XFD070010</p>

		# Setting this register bit to 1 triggers a mode register read or write op
    # eration. When the MR operation is complete, the uMCTL2 automatically cle
    # ars this bit. The other register fields of this register must be written
    #  in a separate APB transaction, before setting this mr_wr bit. It is rec
    # ommended NOT to set this signal if in Init, Deep power-down or MPSM oper
    # ating modes.
		# PSU_DDRC_MRCTRL0_MR_WR                                                          0x0

		# Address of the mode register that is to be written to. - 0000 - MR0 - 00
    # 01 - MR1 - 0010 - MR2 - 0011 - MR3 - 0100 - MR4 - 0101 - MR5 - 0110 - MR
    # 6 - 0111 - MR7 Don't Care for LPDDR2/LPDDR3/LPDDR4 (see MRCTRL1.mr_data
    # for mode register addressing in LPDDR2/LPDDR3/LPDDR4) This signal is als
    # o used for writing to control words of RDIMMs. In that case, it correspo
    # nds to the bank address bits sent to the RDIMM In case of DDR4, the bit[
    # 3:2] corresponds to the bank group bits. Therefore, the bit[3] as well a
    # s the bit[2:0] must be set to an appropriate value which is considered b
    # oth the Address Mirroring of UDIMMs/RDIMMs and the Output Inversion of R
    # DIMMs.
		# PSU_DDRC_MRCTRL0_MR_ADDR                                                        0x0

		# Controls which rank is accessed by MRCTRL0.mr_wr. Normally, it is desire
    # d to access all ranks, so all bits should be set to 1. However, for mult
    # i-rank UDIMMs/RDIMMs which implement address mirroring, it may be necess
    # ary to access ranks individually. Examples (assume uMCTL2 is configured
    # for 4 ranks): - 0x1 - select rank 0 only - 0x2 - select rank 1 only - 0x
    # 5 - select ranks 0 and 2 - 0xA - select ranks 1 and 3 - 0xF - select ran
    # ks 0, 1, 2 and 3
		# PSU_DDRC_MRCTRL0_MR_RANK                                                        0x3

		# Indicates whether Software intervention is allowed via MRCTRL0/MRCTRL1 b
    # efore automatic SDRAM initialization routine or not. For DDR4, this bit
    # can be used to initialize the DDR4 RCD (MR7) before automatic SDRAM init
    # ialization. For LPDDR4, this bit can be used to program additional mode
    # registers before automatic SDRAM initialization if necessary. Note: This
    #  must be cleared to 0 after completing Software operation. Otherwise, SD
    # RAM initialization routine will not re-start. - 0 - Software interventio
    # n is not allowed - 1 - Software intervention is allowed
		# PSU_DDRC_MRCTRL0_SW_INIT_INT                                                    0x0

		# Indicates whether the mode register operation is MRS in PDA mode or not
    # - 0 - MRS - 1 - MRS in Per DRAM Addressability mode
		# PSU_DDRC_MRCTRL0_PDA_EN                                                         0x0

		# Indicates whether the mode register operation is MRS or WR/RD for MPR (o
    # nly supported for DDR4) - 0 - MRS - 1 - WR/RD for MPR
		# PSU_DDRC_MRCTRL0_MPR_EN                                                         0x0

		# Indicates whether the mode register operation is read or write. Only use
    # d for LPDDR2/LPDDR3/LPDDR4/DDR4. - 0 - Write - 1 - Read
		# PSU_DDRC_MRCTRL0_MR_TYPE                                                        0x0

		# Mode Register Read/Write Control Register 0. Note: Do not enable more th
    # an one of the following fields simultaneously: - sw_init_int - pda_en -
    # mpr_en
		#(OFFSET, MASK, VALUE)      (0XFD070010, 0x8000F03FU ,0x00000030U)  */
    mask_write 0XFD070010 0x8000F03F 0x00000030
		# Register : DERATEEN @ 0XFD070020</p>

		# Derate value of tRC for LPDDR4 - 0 - Derating uses +1. - 1 - Derating us
    # es +2. - 2 - Derating uses +3. - 3 - Derating uses +4. Present only in d
    # esigns configured to support LPDDR4. The required number of cycles for d
    # erating can be determined by dividing 3.75ns by the core_ddrc_core_clk p
    # eriod, and rounding up the next integer.
		# PSU_DDRC_DERATEEN_RC_DERATE_VALUE                                               0x2

		# Derate byte Present only in designs configured to support LPDDR2/LPDDR3/
    # LPDDR4 Indicates which byte of the MRR data is used for derating. The ma
    # ximum valid value depends on MEMC_DRAM_TOTAL_DATA_WIDTH.
		# PSU_DDRC_DERATEEN_DERATE_BYTE                                                   0x0

		# Derate value - 0 - Derating uses +1. - 1 - Derating uses +2. Present onl
    # y in designs configured to support LPDDR2/LPDDR3/LPDDR4 Set to 0 for all
    #  LPDDR2 speed grades as derating value of +1.875 ns is less than a core_
    # ddrc_core_clk period. Can be 0 or 1 for LPDDR3/LPDDR4, depending if +1.8
    # 75 ns is less than a core_ddrc_core_clk period or not.
		# PSU_DDRC_DERATEEN_DERATE_VALUE                                                  0x0

		# Enables derating - 0 - Timing parameter derating is disabled - 1 - Timin
    # g parameter derating is enabled using MR4 read value. Present only in de
    # signs configured to support LPDDR2/LPDDR3/LPDDR4 This field must be set
    # to '0' for non-LPDDR2/LPDDR3/LPDDR4 mode.
		# PSU_DDRC_DERATEEN_DERATE_ENABLE                                                 0x0

		# Temperature Derate Enable Register
		#(OFFSET, MASK, VALUE)      (0XFD070020, 0x000003F3U ,0x00000200U)  */
    mask_write 0XFD070020 0x000003F3 0x00000200
		# Register : DERATEINT @ 0XFD070024</p>

		# Interval between two MR4 reads, used to derate the timing parameters. Pr
    # esent only in designs configured to support LPDDR2/LPDDR3/LPDDR4. This r
    # egister must not be set to zero
		# PSU_DDRC_DERATEINT_MR4_READ_INTERVAL                                            0x800000

		# Temperature Derate Interval Register
		#(OFFSET, MASK, VALUE)      (0XFD070024, 0xFFFFFFFFU ,0x00800000U)  */
    mask_write 0XFD070024 0xFFFFFFFF 0x00800000
		# Register : PWRCTL @ 0XFD070030</p>

		# Self refresh state is an intermediate state to enter to Self refresh pow
    # er down state or exit Self refresh power down state for LPDDR4. This reg
    # ister controls transition from the Self refresh state. - 1 - Prohibit tr
    # ansition from Self refresh state - 0 - Allow transition from Self refres
    # h state
		# PSU_DDRC_PWRCTL_STAY_IN_SELFREF                                                 0x0

		# A value of 1 to this register causes system to move to Self Refresh stat
    # e immediately, as long as it is not in INIT or DPD/MPSM operating_mode.
    # This is referred to as Software Entry/Exit to Self Refresh. - 1 - Softwa
    # re Entry to Self Refresh - 0 - Software Exit from Self Refresh
		# PSU_DDRC_PWRCTL_SELFREF_SW                                                      0x0

		# When this is 1, the uMCTL2 puts the SDRAM into maximum power saving mode
    #  when the transaction store is empty. This register must be reset to '0'
    #  to bring uMCTL2 out of maximum power saving mode. Present only in desig
    # ns configured to support DDR4. For non-DDR4, this register should not be
    #  set to 1. Note that MPSM is not supported when using a DWC DDR PHY, if
    # the PHY parameter DWC_AC_CS_USE is disabled, as the MPSM exit sequence r
    # equires the chip-select signal to toggle. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PWRCTL_MPSM_EN                                                         0x0

		# Enable the assertion of dfi_dram_clk_disable whenever a clock is not req
    # uired by the SDRAM. If set to 0, dfi_dram_clk_disable is never asserted.
    #  Assertion of dfi_dram_clk_disable is as follows: In DDR2/DDR3, can only
    #  be asserted in Self Refresh. In DDR4, can be asserted in following: - i
    # n Self Refresh. - in Maximum Power Saving Mode In mDDR/LPDDR2/LPDDR3, ca
    # n be asserted in following: - in Self Refresh - in Power Down - in Deep
    # Power Down - during Normal operation (Clock Stop) In LPDDR4, can be asse
    # rted in following: - in Self Refresh Power Down - in Power Down - during
    #  Normal operation (Clock Stop)
		# PSU_DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE                                         0x0

		# When this is 1, uMCTL2 puts the SDRAM into deep power-down mode when the
    #  transaction store is empty. This register must be reset to '0' to bring
    #  uMCTL2 out of deep power-down mode. Controller performs automatic SDRAM
    #  initialization on deep power-down exit. Present only in designs configu
    # red to support mDDR or LPDDR2 or LPDDR3. For non-mDDR/non-LPDDR2/non-LPD
    # DR3, this register should not be set to 1. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PWRCTL_DEEPPOWERDOWN_EN                                                0x0

		# If true then the uMCTL2 goes into power-down after a programmable number
    #  of cycles 'maximum idle clocks before power down' (PWRTMG.powerdown_to_
    # x32). This register bit may be re-programmed during the course of normal
    #  operation.
		# PSU_DDRC_PWRCTL_POWERDOWN_EN                                                    0x0

		# If true then the uMCTL2 puts the SDRAM into Self Refresh after a program
    # mable number of cycles 'maximum idle clocks before Self Refresh (PWRTMG.
    # selfref_to_x32)'. This register bit may be re-programmed during the cour
    # se of normal operation.
		# PSU_DDRC_PWRCTL_SELFREF_EN                                                      0x0

		# Low Power Control Register
		#(OFFSET, MASK, VALUE)      (0XFD070030, 0x0000007FU ,0x00000000U)  */
    mask_write 0XFD070030 0x0000007F 0x00000000
		# Register : PWRTMG @ 0XFD070034</p>

		# After this many clocks of NOP or deselect the uMCTL2 automatically puts
    # the SDRAM into Self Refresh. This must be enabled in the PWRCTL.selfref_
    # en. Unit: Multiples of 32 clocks. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PWRTMG_SELFREF_TO_X32                                                  0x40

		# Minimum deep power-down time. For mDDR, value from the JEDEC specificati
    # on is 0 as mDDR exits from deep power-down mode immediately after PWRCTL
    # .deeppowerdown_en is de-asserted. For LPDDR2/LPDDR3, value from the JEDE
    # C specification is 500us. Unit: Multiples of 4096 clocks. Present only i
    # n designs configured to support mDDR, LPDDR2 or LPDDR3. FOR PERFORMANCE
    # ONLY.
		# PSU_DDRC_PWRTMG_T_DPD_X4096                                                     0x84

		# After this many clocks of NOP or deselect the uMCTL2 automatically puts
    # the SDRAM into power-down. This must be enabled in the PWRCTL.powerdown_
    # en. Unit: Multiples of 32 clocks FOR PERFORMANCE ONLY.
		# PSU_DDRC_PWRTMG_POWERDOWN_TO_X32                                                0x10

		# Low Power Timing Register
		#(OFFSET, MASK, VALUE)      (0XFD070034, 0x00FFFF1FU ,0x00408410U)  */
    mask_write 0XFD070034 0x00FFFF1F 0x00408410
		# Register : RFSHCTL0 @ 0XFD070050</p>

		# Threshold value in number of clock cycles before the critical refresh or
    #  page timer expires. A critical refresh is to be issued before this thre
    # shold is reached. It is recommended that this not be changed from the de
    # fault value, currently shown as 0x2. It must always be less than interna
    # lly used t_rfc_nom_x32. Note that, in LPDDR2/LPDDR3/LPDDR4, internally u
    # sed t_rfc_nom_x32 may be equal to RFSHTMG.t_rfc_nom_x32>>2 if derating i
    # s enabled (DERATEEN.derate_enable=1). Otherwise, internally used t_rfc_n
    # om_x32 will be equal to RFSHTMG.t_rfc_nom_x32. Unit: Multiples of 32 clo
    # cks.
		# PSU_DDRC_RFSHCTL0_REFRESH_MARGIN                                                0x2

		# If the refresh timer (tRFCnom, also known as tREFI) has expired at least
    #  once, but it has not expired (RFSHCTL0.refresh_burst+1) times yet, then
    #  a speculative refresh may be performed. A speculative refresh is a refr
    # esh performed at a time when refresh would be useful, but before it is a
    # bsolutely required. When the SDRAM bus is idle for a period of time dete
    # rmined by this RFSHCTL0.refresh_to_x32 and the refresh timer has expired
    #  at least once since the last refresh, then a speculative refresh is per
    # formed. Speculative refreshes continues successively until there are no
    # refreshes pending or until new reads or writes are issued to the uMCTL2.
    #  FOR PERFORMANCE ONLY.
		# PSU_DDRC_RFSHCTL0_REFRESH_TO_X32                                                0x10

		# The programmed value + 1 is the number of refresh timeouts that is allow
    # ed to accumulate before traffic is blocked and the refreshes are forced
    # to execute. Closing pages to perform a refresh is a one-time penalty tha
    # t must be paid for each group of refreshes. Therefore, performing refres
    # hes in a burst reduces the per-refresh penalty of these page closings. H
    # igher numbers for RFSHCTL.refresh_burst slightly increases utilization;
    # lower numbers decreases the worst-case latency associated with refreshes
    # . - 0 - single refresh - 1 - burst-of-2 refresh - 7 - burst-of-8 refresh
    #  For information on burst refresh feature refer to section 3.9 of DDR2 J
    # EDEC specification - JESD79-2F.pdf. For DDR2/3, the refresh is always pe
    # r-rank and not per-bank. The rank refresh can be accumulated over 8*tREF
    # I cycles using the burst refresh feature. In DDR4 mode, according to Fin
    # e Granularity feature, 8 refreshes can be postponed in 1X mode, 16 refre
    # shes in 2X mode and 32 refreshes in 4X mode. If using PHY-initiated upda
    # tes, care must be taken in the setting of RFSHCTL0.refresh_burst, to ens
    # ure that tRFCmax is not violated due to a PHY-initiated update occurring
    #  shortly before a refresh burst was due. In this situation, the refresh
    # burst will be delayed until the PHY-initiated update is complete.
		# PSU_DDRC_RFSHCTL0_REFRESH_BURST                                                 0x0

		# - 1 - Per bank refresh; - 0 - All bank refresh. Per bank refresh allows
    # traffic to flow to other banks. Per bank refresh is not supported by all
    #  LPDDR2 devices but should be supported by all LPDDR3/LPDDR4 devices. Pr
    # esent only in designs configured to support LPDDR2/LPDDR3/LPDDR4
		# PSU_DDRC_RFSHCTL0_PER_BANK_REFRESH                                              0x0

		# Refresh Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070050, 0x00F1F1F4U ,0x00210000U)  */
    mask_write 0XFD070050 0x00F1F1F4 0x00210000
		# Register : RFSHCTL1 @ 0XFD070054</p>

		# Refresh timer start for rank 1 (only present in multi-rank configuration
    # s). This is useful in staggering the refreshes to multiple ranks to help
    #  traffic to proceed. This is explained in Refresh Controls section of ar
    # chitecture chapter. Unit: Multiples of 32 clocks. FOR PERFORMANCE ONLY.
		# PSU_DDRC_RFSHCTL1_REFRESH_TIMER1_START_VALUE_X32                                0x0

		# Refresh timer start for rank 0 (only present in multi-rank configuration
    # s). This is useful in staggering the refreshes to multiple ranks to help
    #  traffic to proceed. This is explained in Refresh Controls section of ar
    # chitecture chapter. Unit: Multiples of 32 clocks. FOR PERFORMANCE ONLY.
		# PSU_DDRC_RFSHCTL1_REFRESH_TIMER0_START_VALUE_X32                                0x0

		# Refresh Control Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070054, 0x0FFF0FFFU ,0x00000000U)  */
    mask_write 0XFD070054 0x0FFF0FFF 0x00000000
		# Register : RFSHCTL3 @ 0XFD070060</p>

		# Fine Granularity Refresh Mode - 000 - Fixed 1x (Normal mode) - 001 - Fix
    # ed 2x - 010 - Fixed 4x - 101 - Enable on the fly 2x (not supported) - 11
    # 0 - Enable on the fly 4x (not supported) - Everything else - reserved No
    # te: The on-the-fly modes is not supported in this version of the uMCTL2.
    #  Note: This must be set up while the Controller is in reset or while the
    #  Controller is in self-refresh mode. Changing this during normal operati
    # on is not allowed. Making this a dynamic register will be supported in f
    # uture version of the uMCTL2.
		# PSU_DDRC_RFSHCTL3_REFRESH_MODE                                                  0x0

		# Toggle this signal (either from 0 to 1 or from 1 to 0) to indicate that
    # the refresh register(s) have been updated. The value is automatically up
    # dated when exiting reset, so it does not need to be toggled initially.
		# PSU_DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL                                          0x0

		# When '1', disable auto-refresh generated by the uMCTL2. When auto-refres
    # h is disabled, the SoC core must generate refreshes using the registers
    # reg_ddrc_rank0_refresh, reg_ddrc_rank1_refresh, reg_ddrc_rank2_refresh a
    # nd reg_ddrc_rank3_refresh. When dis_auto_refresh transitions from 0 to 1
    # , any pending refreshes are immediately scheduled by the uMCTL2. If DDR4
    #  CRC/parity retry is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), d
    # isable auto-refresh is not supported, and this bit must be set to '0'. T
    # his register field is changeable on the fly.
		# PSU_DDRC_RFSHCTL3_DIS_AUTO_REFRESH                                              0x1

		# Refresh Control Register 3
		#(OFFSET, MASK, VALUE)      (0XFD070060, 0x00000073U ,0x00000001U)  */
    mask_write 0XFD070060 0x00000073 0x00000001
		# Register : RFSHTMG @ 0XFD070064</p>

		# tREFI: Average time interval between refreshes per rank (Specification:
    # 7.8us for DDR2, DDR3 and DDR4. See JEDEC specification for mDDR, LPDDR2,
    #  LPDDR3 and LPDDR4). For LPDDR2/LPDDR3/LPDDR4: - if using all-bank refre
    # shes (RFSHCTL0.per_bank_refresh = 0), this register should be set to tRE
    # FIab - if using per-bank refreshes (RFSHCTL0.per_bank_refresh = 1), this
    #  register should be set to tREFIpb For configurations with MEMC_FREQ_RAT
    # IO=2, program this to (tREFI/2), no rounding up. In DDR4 mode, tREFI val
    # ue is different depending on the refresh mode. The user should program t
    # he appropriate value from the spec based on the value programmed in the
    # refresh mode register. Note that RFSHTMG.t_rfc_nom_x32 * 32 must be grea
    # ter than RFSHTMG.t_rfc_min, and RFSHTMG.t_rfc_nom_x32 must be greater th
    # an 0x1. Unit: Multiples of 32 clocks.
		# PSU_DDRC_RFSHTMG_T_RFC_NOM_X32                                                  0x81

		# Used only when LPDDR3 memory type is connected. Should only be changed w
    # hen uMCTL2 is in reset. Specifies whether to use the tREFBW parameter (r
    # equired by some LPDDR3 devices which comply with earlier versions of the
    #  LPDDR3 JEDEC specification) or not: - 0 - tREFBW parameter not used - 1
    #  - tREFBW parameter used
		# PSU_DDRC_RFSHTMG_LPDDR3_TREFBW_EN                                               0x1

		# tRFC (min): Minimum time from refresh to refresh or activate. For MEMC_F
    # REQ_RATIO=1 configurations, t_rfc_min should be set to RoundUp(tRFCmin/t
    # CK). For MEMC_FREQ_RATIO=2 configurations, t_rfc_min should be set to Ro
    # undUp(RoundUp(tRFCmin/tCK)/2). In LPDDR2/LPDDR3/LPDDR4 mode: - if using
    # all-bank refreshes, the tRFCmin value in the above equations is equal to
    #  tRFCab - if using per-bank refreshes, the tRFCmin value in the above eq
    # uations is equal to tRFCpb In DDR4 mode, the tRFCmin value in the above
    # equations is different depending on the refresh mode (fixed 1X,2X,4X) an
    # d the device density. The user should program the appropriate value from
    #  the spec based on the 'refresh_mode' and the device density that is use
    # d. Unit: Clocks.
		# PSU_DDRC_RFSHTMG_T_RFC_MIN                                                      0x8b

		# Refresh Timing Register
		#(OFFSET, MASK, VALUE)      (0XFD070064, 0x0FFF83FFU ,0x0081808BU)  */
    mask_write 0XFD070064 0x0FFF83FF 0x0081808B
		# Register : ECCCFG0 @ 0XFD070070</p>

		# Disable ECC scrubs. Valid only when ECCCFG0.ecc_mode = 3'b100 and MEMC_U
    # SE_RMW is defined
		# PSU_DDRC_ECCCFG0_DIS_SCRUB                                                      0x1

		# ECC mode indicator - 000 - ECC disabled - 100 - ECC enabled - SEC/DED ov
    # er 1 beat - all other settings are reserved for future use
		# PSU_DDRC_ECCCFG0_ECC_MODE                                                       0x0

		# ECC Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070070, 0x00000017U ,0x00000010U)  */
    mask_write 0XFD070070 0x00000017 0x00000010
		# Register : ECCCFG1 @ 0XFD070074</p>

		# Selects whether to poison 1 or 2 bits - if 0 -> 2-bit (uncorrectable) da
    # ta poisoning, if 1 -> 1-bit (correctable) data poisoning, if ECCCFG1.dat
    # a_poison_en=1
		# PSU_DDRC_ECCCFG1_DATA_POISON_BIT                                                0x0

		# Enable ECC data poisoning - introduces ECC errors on writes to address s
    # pecified by the ECCPOISONADDR0/1 registers
		# PSU_DDRC_ECCCFG1_DATA_POISON_EN                                                 0x0

		# ECC Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070074, 0x00000003U ,0x00000000U)  */
    mask_write 0XFD070074 0x00000003 0x00000000
		# Register : CRCPARCTL1 @ 0XFD0700C4</p>

		# The maximum number of DFI PHY clock cycles allowed from the assertion of
    #  the dfi_rddata_en signal to the assertion of each of the corresponding
    # bits of the dfi_rddata_valid signal. This corresponds to the DFI timing
    # parameter tphy_rdlat. Refer to PHY specification for correct value. This
    #  value it only used for detecting read data timeout when DDR4 retry is e
    # nabled by CRCPARCTL1.crc_parity_retry_enable=1. Maximum supported value:
    #  - 1:1 Frequency mode : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_r
    # dlat < 'd114 - 1:2 Frequency mode ANDAND DFITMG0.dfi_rddata_use_sdr == 1
    #  : CRCPARCTL1.dfi_t_phy_rdlat < 64 - 1:2 Frequency mode ANDAND DFITMG0.d
    # fi_rddata_use_sdr == 0 : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_
    # rdlat < 'd114 Unit: DFI Clocks
		# PSU_DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT                                             0x10

		# After a Parity or CRC error is flagged on dfi_alert_n signal, the softwa
    # re has an option to read the mode registers in the DRAM before the hardw
    # are begins the retry process - 1: Wait for software to read/write the mo
    # de registers before hardware begins the retry. After software is done wi
    # th its operations, it will clear the alert interrupt register bit - 0: H
    # ardware can begin the retry right away after the dfi_alert_n pulse goes
    # away. The value on this register is valid only when retry is enabled (PA
    # RCTRL.crc_parity_retry_enable = 1) If this register is set to 1 and if t
    # he software doesn't clear the interrupt register after handling the pari
    # ty/CRC error, then the hardware will not begin the retry process and the
    #  system will hang. In the case of Parity/CRC error, there are two possib
    # ilities when the software doesn't reset MR5[4] to 0. - (i) If 'Persisten
    # t parity' mode register bit is NOT set: the commands sent during retry a
    # nd normal operation are executed without parity checking. The value in t
    # he Parity error log register MPR Page 1 is valid. - (ii) If 'Persistent
    # parity' mode register bit is SET: Parity checking is done for commands s
    # ent during retry and normal operation. If multiple errors occur before M
    # R5[4] is cleared, the error log in MPR Page 1 should be treated as 'Don'
    # t care'.
		# PSU_DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW                                           0x1

		# - 1: Enable command retry mechanism in case of C/A Parity or CRC error -
    #  0: Disable command retry mechanism when C/A Parity or CRC features are
    # enabled. Note that retry functionality is not supported if burst chop is
    #  enabled (MSTR.burstchop = 1) and/or disable auto-refresh is enabled (RF
    # SHCTL3.dis_auto_refresh = 1)
		# PSU_DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE                                     0x0

		# CRC Calculation setting register - 1: CRC includes DM signal - 0: CRC no
    # t includes DM signal Present only in designs configured to support DDR4.
		# PSU_DDRC_CRCPARCTL1_CRC_INC_DM                                                  0x0

		# CRC enable Register - 1: Enable generation of CRC - 0: Disable generatio
    # n of CRC The setting of this register should match the CRC mode register
    #  setting in the DRAM.
		# PSU_DDRC_CRCPARCTL1_CRC_ENABLE                                                  0x0

		# C/A Parity enable register - 1: Enable generation of C/A parity and dete
    # ction of C/A parity error - 0: Disable generation of C/A parity and disa
    # ble detection of C/A parity error If RCD's parity error detection or SDR
    # AM's parity detection is enabled, this register should be 1.
		# PSU_DDRC_CRCPARCTL1_PARITY_ENABLE                                               0x0

		# CRC Parity Control Register1
		#(OFFSET, MASK, VALUE)      (0XFD0700C4, 0x3F000391U ,0x10000200U)  */
    mask_write 0XFD0700C4 0x3F000391 0x10000200
		# Register : CRCPARCTL2 @ 0XFD0700C8</p>

		# Value from the DRAM spec indicating the maximum width of the dfi_alert_n
    #  pulse when a parity error occurs. Recommended values: - tPAR_ALERT_PW.M
    # AX For configurations with MEMC_FREQ_RATIO=2, program this to tPAR_ALERT
    # _PW.MAX/2 and round up to next integer value. Values of 0, 1 and 2 are i
    # llegal. This value must be greater than CRCPARCTL2.t_crc_alert_pw_max.
		# PSU_DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX                                          0x40

		# Value from the DRAM spec indicating the maximum width of the dfi_alert_n
    #  pulse when a CRC error occurs. Recommended values: - tCRC_ALERT_PW.MAX
    # For configurations with MEMC_FREQ_RATIO=2, program this to tCRC_ALERT_PW
    # .MAX/2 and round up to next integer value. Values of 0, 1 and 2 are ille
    # gal. This value must be less than CRCPARCTL2.t_par_alert_pw_max.
		# PSU_DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX                                          0x5

		# Indicates the maximum duration in number of DRAM clock cycles for which
    # a command should be held in the Command Retry FIFO before it is popped o
    # ut. Every location in the Command Retry FIFO has an associated down coun
    # ting timer that will use this register as the start value. The down coun
    # ting starts when a command is loaded into the FIFO. The timer counts dow
    # n every 4 DRAM cycles. When the counter reaches zero, the entry is poppe
    # d from the FIFO. All the counters are frozen, if a C/A Parity or CRC err
    # or occurs before the counter reaches zero. The counter is reset to 0, af
    # ter all the commands in the FIFO are retried. Recommended(minimum) value
    # s: - Only C/A Parity is enabled. RoundUp((PHY Command Latency(DRAM CLK)
    # + CAL + RDIMM delay + tPAR_ALERT_ON.max + tPAR_UNKNOWN + PHY Alert Laten
    # cy(DRAM CLK) + board delay) / 4) + 2 - Both C/A Parity and CRC is enable
    # d/ Only CRC is enabled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + R
    # DIMM delay + WL + 5(BL10)+ tCRC_ALERT.max + PHY Alert Latency(DRAM CLK)
    # + board delay) / 4) + 2 Note 1: All value (e.g. tPAR_ALERT_ON) should be
    #  in terms of DRAM Clock and round up Note 2: Board delay(Command/Alert_n
    # ) should be considered. Note 3: Use the worst case(longer) value for PHY
    #  Latencies/Board delay Note 4: The Recommended values are minimum value
    # to be set. For mode detail, See 'Calculation of FIFO Depth' section. Max
    #  value can be set to this register is defined below: - MEMC_BURST_LENGTH
    #  == 16 Full bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2
    #  Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Half b
    # us Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-4 Half bus Mod
    # e (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-6 Quarter bus Mode (C
    # RC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-8 Quarter bus Mode (CRC=
    # ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-12 - MEMC_BURST_LENGTH != 16
    #  Full bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-1 Full
    # bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mod
    # e (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mode (CRC
    # =ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Quarter bus Mode (CRC=OFF
    # ) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-4 Quarter bus Mode (CRC=ON) Ma
    # x value = UMCTL2_RETRY_CMD_FIFO_DEPTH-6 Values of 0, 1 and 2 are illegal
    # .
		# PSU_DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4                                0x1f

		# CRC Parity Control Register2
		#(OFFSET, MASK, VALUE)      (0XFD0700C8, 0x01FF1F3FU ,0x0040051FU)  */
    mask_write 0XFD0700C8 0x01FF1F3F 0x0040051F
		# Register : INIT0 @ 0XFD0700D0</p>

		# If lower bit is enabled the SDRAM initialization routine is skipped. The
    #  upper bit decides what state the controller starts up in when reset is
    # removed - 00 - SDRAM Intialization routine is run after power-up - 01 -
    # SDRAM Intialization routine is skipped after power-up. Controller starts
    #  up in Normal Mode - 11 - SDRAM Intialization routine is skipped after p
    # ower-up. Controller starts up in Self-refresh Mode - 10 - SDRAM Intializ
    # ation routine is run after power-up. Note: The only 2'b00 is supported f
    # or LPDDR4 in this version of the uMCTL2.
		# PSU_DDRC_INIT0_SKIP_DRAM_INIT                                                   0x0

		# Cycles to wait after driving CKE high to start the SDRAM initialization
    # sequence. Unit: 1024 clocks. DDR2 typically requires a 400 ns delay, req
    # uiring this value to be programmed to 2 at all clock speeds. LPDDR2/LPDD
    # R3 typically requires this to be programmed for a delay of 200 us. LPDDR
    # 4 typically requires this to be programmed for a delay of 2 us. For conf
    # igurations with MEMC_FREQ_RATIO=2, program this to JEDEC spec value divi
    # ded by 2, and round it up to next integer value.
		# PSU_DDRC_INIT0_POST_CKE_X1024                                                   0x2

		# Cycles to wait after reset before driving CKE high to start the SDRAM in
    # itialization sequence. Unit: 1024 clock cycles. DDR2 specifications typi
    # cally require this to be programmed for a delay of >= 200 us. LPDDR2/LPD
    # DR3: tINIT1 of 100 ns (min) LPDDR4: tINIT3 of 2 ms (min) For configurati
    # ons with MEMC_FREQ_RATIO=2, program this to JEDEC spec value divided by
    # 2, and round it up to next integer value.
		# PSU_DDRC_INIT0_PRE_CKE_X1024                                                    0x106

		# SDRAM Initialization Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0700D0, 0xC3FF0FFFU ,0x00020106U)  */
    mask_write 0XFD0700D0 0xC3FF0FFF 0x00020106
		# Register : INIT1 @ 0XFD0700D4</p>

		# Number of cycles to assert SDRAM reset signal during init sequence. This
    #  is only present for designs supporting DDR3, DDR4 or LPDDR4 devices. Fo
    # r use with a DDR PHY, this should be set to a minimum of 1
		# PSU_DDRC_INIT1_DRAM_RSTN_X1024                                                  0x2

		# Cycles to wait after completing the SDRAM initialization sequence before
    #  starting the dynamic scheduler. Unit: Counts of a global timer that pul
    # ses every 32 clock cycles. There is no known specific requirement for th
    # is; it may be set to zero.
		# PSU_DDRC_INIT1_FINAL_WAIT_X32                                                   0x0

		# Wait period before driving the OCD complete command to SDRAM. Unit: Coun
    # ts of a global timer that pulses every 32 clock cycles. There is no know
    # n specific requirement for this; it may be set to zero.
		# PSU_DDRC_INIT1_PRE_OCD_X32                                                      0x0

		# SDRAM Initialization Register 1
		#(OFFSET, MASK, VALUE)      (0XFD0700D4, 0x01FF7F0FU ,0x00020000U)  */
    mask_write 0XFD0700D4 0x01FF7F0F 0x00020000
		# Register : INIT2 @ 0XFD0700D8</p>

		# Idle time after the reset command, tINIT4. Present only in designs confi
    # gured to support LPDDR2. Unit: 32 clock cycles.
		# PSU_DDRC_INIT2_IDLE_AFTER_RESET_X32                                             0x23

		# Time to wait after the first CKE high, tINIT2. Present only in designs c
    # onfigured to support LPDDR2/LPDDR3. Unit: 1 clock cycle. LPDDR2/LPDDR3 t
    # ypically requires 5 x tCK delay.
		# PSU_DDRC_INIT2_MIN_STABLE_CLOCK_X1                                              0x5

		# SDRAM Initialization Register 2
		#(OFFSET, MASK, VALUE)      (0XFD0700D8, 0x0000FF0FU ,0x00002305U)  */
    mask_write 0XFD0700D8 0x0000FF0F 0x00002305
		# Register : INIT3 @ 0XFD0700DC</p>

		# DDR2: Value to write to MR register. Bit 8 is for DLL and the setting he
    # re is ignored. The uMCTL2 sets this bit appropriately. DDR3/DDR4: Value
    # loaded into MR0 register. mDDR: Value to write to MR register. LPDDR2/LP
    # DDR3/LPDDR4 - Value to write to MR1 register
		# PSU_DDRC_INIT3_MR                                                               0x730

		# DDR2: Value to write to EMR register. Bits 9:7 are for OCD and the setti
    # ng in this register is ignored. The uMCTL2 sets those bits appropriately
    # . DDR3/DDR4: Value to write to MR1 register Set bit 7 to 0. If PHY-evalu
    # ation mode training is enabled, this bit is set appropriately by the uMC
    # TL2 during write leveling. mDDR: Value to write to EMR register. LPDDR2/
    # LPDDR3/LPDDR4 - Value to write to MR2 register
		# PSU_DDRC_INIT3_EMR                                                              0x301

		# SDRAM Initialization Register 3
		#(OFFSET, MASK, VALUE)      (0XFD0700DC, 0xFFFFFFFFU ,0x07300301U)  */
    mask_write 0XFD0700DC 0xFFFFFFFF 0x07300301
		# Register : INIT4 @ 0XFD0700E0</p>

		# DDR2: Value to write to EMR2 register. DDR3/DDR4: Value to write to MR2
    # register LPDDR2/LPDDR3/LPDDR4: Value to write to MR3 register mDDR: Unus
    # ed
		# PSU_DDRC_INIT4_EMR2                                                             0x20

		# DDR2: Value to write to EMR3 register. DDR3/DDR4: Value to write to MR3
    # register mDDR/LPDDR2/LPDDR3: Unused LPDDR4: Value to write to MR13 regis
    # ter
		# PSU_DDRC_INIT4_EMR3                                                             0x200

		# SDRAM Initialization Register 4
		#(OFFSET, MASK, VALUE)      (0XFD0700E0, 0xFFFFFFFFU ,0x00200200U)  */
    mask_write 0XFD0700E0 0xFFFFFFFF 0x00200200
		# Register : INIT5 @ 0XFD0700E4</p>

		# ZQ initial calibration, tZQINIT. Present only in designs configured to s
    # upport DDR3 or DDR4 or LPDDR2/LPDDR3. Unit: 32 clock cycles. DDR3 typica
    # lly requires 512 clocks. DDR4 requires 1024 clocks. LPDDR2/LPDDR3 requir
    # es 1 us.
		# PSU_DDRC_INIT5_DEV_ZQINIT_X32                                                   0x21

		# Maximum duration of the auto initialization, tINIT5. Present only in des
    # igns configured to support LPDDR2/LPDDR3. LPDDR2/LPDDR3 typically requir
    # es 10 us.
		# PSU_DDRC_INIT5_MAX_AUTO_INIT_X1024                                              0x4

		# SDRAM Initialization Register 5
		#(OFFSET, MASK, VALUE)      (0XFD0700E4, 0x00FF03FFU ,0x00210004U)  */
    mask_write 0XFD0700E4 0x00FF03FF 0x00210004
		# Register : INIT6 @ 0XFD0700E8</p>

		# DDR4- Value to be loaded into SDRAM MR4 registers. Used in DDR4 designs
    # only.
		# PSU_DDRC_INIT6_MR4                                                              0x0

		# DDR4- Value to be loaded into SDRAM MR5 registers. Used in DDR4 designs
    # only.
		# PSU_DDRC_INIT6_MR5                                                              0x6c0

		# SDRAM Initialization Register 6
		#(OFFSET, MASK, VALUE)      (0XFD0700E8, 0xFFFFFFFFU ,0x000006C0U)  */
    mask_write 0XFD0700E8 0xFFFFFFFF 0x000006C0
		# Register : INIT7 @ 0XFD0700EC</p>

		# DDR4- Value to be loaded into SDRAM MR6 registers. Used in DDR4 designs
    # only.
		# PSU_DDRC_INIT7_MR6                                                              0x819

		# SDRAM Initialization Register 7
		#(OFFSET, MASK, VALUE)      (0XFD0700EC, 0xFFFF0000U ,0x08190000U)  */
    mask_write 0XFD0700EC 0xFFFF0000 0x08190000
		# Register : DIMMCTL @ 0XFD0700F0</p>

		# Disabling Address Mirroring for BG bits. When this is set to 1, BG0 and
    # BG1 are NOT swapped even if Address Mirroring is enabled. This will be r
    # equired for DDR4 DIMMs with x16 devices. - 1 - BG0 and BG1 are NOT swapp
    # ed. - 0 - BG0 and BG1 are swapped if address mirroring is enabled.
		# PSU_DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING                                          0x0

		# Enable for BG1 bit of MRS command. BG1 bit of the mode register address
    # is specified as RFU (Reserved for Future Use) and must be programmed to
    # 0 during MRS. In case where DRAMs which do not have BG1 are attached and
    #  both the CA parity and the Output Inversion are enabled, this must be s
    # et to 0, so that the calculation of CA parity will not include BG1 bit.
    # Note: This has no effect on the address of any other memory accesses, or
    #  of software-driven mode register accesses. If address mirroring is enab
    # led, this is applied to BG1 of even ranks and BG0 of odd ranks. - 1 - En
    # abled - 0 - Disabled
		# PSU_DDRC_DIMMCTL_MRS_BG1_EN                                                     0x1

		# Enable for A17 bit of MRS command. A17 bit of the mode register address
    # is specified as RFU (Reserved for Future Use) and must be programmed to
    # 0 during MRS. In case where DRAMs which do not have A17 are attached and
    #  the Output Inversion are enabled, this must be set to 0, so that the ca
    # lculation of CA parity will not include A17 bit. Note: This has no effec
    # t on the address of any other memory accesses, or of software-driven mod
    # e register accesses. - 1 - Enabled - 0 - Disabled
		# PSU_DDRC_DIMMCTL_MRS_A17_EN                                                     0x0

		# Output Inversion Enable (for DDR4 RDIMM implementations only). DDR4 RDIM
    # M implements the Output Inversion feature by default, which means that t
    # he following address, bank address and bank group bits of B-side DRAMs a
    # re inverted: A3-A9, A11, A13, A17, BA0-BA1, BG0-BG1. Setting this bit en
    # sures that, for mode register accesses generated by the uMCTL2 during th
    # e automatic initialization routine and enabling of a particular DDR4 fea
    # ture, separate A-side and B-side mode register accesses are generated. F
    # or B-side mode register accesses, these bits are inverted within the uMC
    # TL2 to compensate for this RDIMM inversion. Note: This has no effect on
    # the address of any other memory accesses, or of software-driven mode reg
    # ister accesses. - 1 - Implement output inversion for B-side DRAMs. - 0 -
    #  Do not implement output inversion for B-side DRAMs.
		# PSU_DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN                                             0x0

		# Address Mirroring Enable (for multi-rank UDIMM implementations and multi
    # -rank DDR4 RDIMM implementations). Some UDIMMs and DDR4 RDIMMs implement
    #  address mirroring for odd ranks, which means that the following address
    # , bank address and bank group bits are swapped: (A3, A4), (A5, A6), (A7,
    #  A8), (BA0, BA1) and also (A11, A13), (BG0, BG1) for the DDR4. Setting t
    # his bit ensures that, for mode register accesses during the automatic in
    # itialization routine, these bits are swapped within the uMCTL2 to compen
    # sate for this UDIMM/RDIMM swapping. In addition to the automatic initial
    # ization routine, in case of DDR4 UDIMM/RDIMM, they are swapped during th
    # e automatic MRS access to enable/disable of a particular DDR4 feature. N
    # ote: This has no effect on the address of any other memory accesses, or
    # of software-driven mode register accesses. This is not supported for mDD
    # R, LPDDR2, LPDDR3 or LPDDR4 SDRAMs. Note: In case of x16 DDR4 DIMMs, BG1
    #  output of MRS for the odd ranks is same as BG0 because BG1 is invalid,
    # hence dimm_dis_bg_mirroring register must be set to 1. - 1 - For odd ran
    # ks, implement address mirroring for MRS commands to during initializatio
    # n and for any automatic DDR4 MRS commands (to be used if UDIMM/RDIMM imp
    # lements address mirroring) - 0 - Do not implement address mirroring
		# PSU_DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN                                              0x0

		# Staggering enable for multi-rank accesses (for multi-rank UDIMM and RDIM
    # M implementations only). This is not supported for mDDR, LPDDR2, LPDDR3
    # or LPDDR4 SDRAMs. Note: Even if this bit is set it does not take care of
    #  software driven MR commands (via MRCTRL0/MRCTRL1), where software is re
    # sponsible to send them to seperate ranks as appropriate. - 1 - (DDR4) Se
    # nd MRS commands to each ranks seperately - 1 - (non-DDR4) Send all comma
    # nds to even and odd ranks seperately - 0 - Do not stagger accesses
		# PSU_DDRC_DIMMCTL_DIMM_STAGGER_CS_EN                                             0x0

		# DIMM Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0700F0, 0x0000003FU ,0x00000010U)  */
    mask_write 0XFD0700F0 0x0000003F 0x00000010
		# Register : RANKCTL @ 0XFD0700F4</p>

		# Only present for multi-rank configurations. Indicates the number of cloc
    # ks of gap in data responses when performing consecutive writes to differ
    # ent ranks. This is used to switch the delays in the PHY to match the ran
    # k requirements. This value should consider both PHY requirement and ODT
    # requirement. - PHY requirement: tphy_wrcsgap + 1 (see PHY databook for v
    # alue of tphy_wrcsgap) If CRC feature is enabled, should be increased by
    # 1. If write preamble is set to 2tCK(DDR4/LPDDR4 only), should be increas
    # ed by 1. If write postamble is set to 1.5tCK(LPDDR4 only), should be inc
    # reased by 1. - ODT requirement: The value programmed in this register ta
    # kes care of the ODT switch off timing requirement when switching ranks d
    # uring writes. For LPDDR4, the requirement is ODTLoff - ODTLon - BL/2 + 1
    #  For configurations with MEMC_FREQ_RATIO=1, program this to the larger o
    # f PHY requirement or ODT requirement. For configurations with MEMC_FREQ_
    # RATIO=2, program this to the larger value divided by two and round it up
    #  to the next integer.
		# PSU_DDRC_RANKCTL_DIFF_RANK_WR_GAP                                               0x6

		# Only present for multi-rank configurations. Indicates the number of cloc
    # ks of gap in data responses when performing consecutive reads to differe
    # nt ranks. This is used to switch the delays in the PHY to match the rank
    #  requirements. This value should consider both PHY requirement and ODT r
    # equirement. - PHY requirement: tphy_rdcsgap + 1 (see PHY databook for va
    # lue of tphy_rdcsgap) If read preamble is set to 2tCK(DDR4/LPDDR4 only),
    # should be increased by 1. If read postamble is set to 1.5tCK(LPDDR4 only
    # ), should be increased by 1. - ODT requirement: The value programmed in
    # this register takes care of the ODT switch off timing requirement when s
    # witching ranks during reads. For configurations with MEMC_FREQ_RATIO=1,
    # program this to the larger of PHY requirement or ODT requirement. For co
    # nfigurations with MEMC_FREQ_RATIO=2, program this to the larger value di
    # vided by two and round it up to the next integer.
		# PSU_DDRC_RANKCTL_DIFF_RANK_RD_GAP                                               0x6

		# Only present for multi-rank configurations. Background: Reads to the sam
    # e rank can be performed back-to-back. Reads to different ranks require a
    # dditional gap dictated by the register RANKCTL.diff_rank_rd_gap. This is
    #  to avoid possible data bus contention as well as to give PHY enough tim
    # e to switch the delay when changing ranks. The uMCTL2 arbitrates for bus
    #  access on a cycle-by-cycle basis; therefore after a read is scheduled,
    # there are few clock cycles (determined by the value on RANKCTL.diff_rank
    # _rd_gap register) in which only reads from the same rank are eligible to
    #  be scheduled. This prevents reads from other ranks from having fair acc
    # ess to the data bus. This parameter represents the maximum number of rea
    # ds that can be scheduled consecutively to the same rank. After this numb
    # er is reached, a delay equal to RANKCTL.diff_rank_rd_gap is inserted by
    # the scheduler to allow all ranks a fair opportunity to be scheduled. Hig
    # her numbers increase bandwidth utilization, lower numbers increase fairn
    # ess. This feature can be DISABLED by setting this register to 0. When se
    # t to 0, the Controller will stay on the same rank as long as commands ar
    # e available for it. Minimum programmable value is 0 (feature disabled) a
    # nd maximum programmable value is 0xF. FOR PERFORMANCE ONLY.
		# PSU_DDRC_RANKCTL_MAX_RANK_RD                                                    0xf

		# Rank Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0700F4, 0x00000FFFU ,0x0000066FU)  */
    mask_write 0XFD0700F4 0x00000FFF 0x0000066F
		# Register : DRAMTMG0 @ 0XFD070100</p>

		# Minimum time between write and precharge to same bank. Unit: Clocks Spec
    # ifications: WL + BL/2 + tWR = approximately 8 cycles + 15 ns = 14 clocks
    #  @400MHz and less for lower frequencies where: - WL = write latency - BL
    #  = burst length. This must match the value programmed in the BL bit of t
    # he mode register to the SDRAM. BST (burst terminate) is not supported at
    #  present. - tWR = Write recovery time. This comes directly from the SDRA
    # M specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 for this p
    # arameter. For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the
    #  above value by 2. No rounding up. For configurations with MEMC_FREQ_RAT
    # IO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it u
    # p to the next integer value.
		# PSU_DDRC_DRAMTMG0_WR2PRE                                                        0x11

		# tFAW Valid only when 8 or more banks(or banks x bank groups) are present
    # . In 8-bank design, at most 4 banks must be activated in a rolling windo
    # w of tFAW cycles. For configurations with MEMC_FREQ_RATIO=2, program thi
    # s to (tFAW/2) and round up to next integer value. In a 4-bank design, se
    # t this register to 0x1 independent of the MEMC_FREQ_RATIO configuration.
    #  Unit: Clocks
		# PSU_DDRC_DRAMTMG0_T_FAW                                                         0x10

		# tRAS(max): Maximum time between activate and precharge to same bank. Thi
    # s is the maximum time that a page can be kept open Minimum value of this
    #  register is 1. Zero is invalid. For configurations with MEMC_FREQ_RATIO
    # =2, program this to (tRAS(max)-1)/2. No rounding up. Unit: Multiples of
    # 1024 clocks.
		# PSU_DDRC_DRAMTMG0_T_RAS_MAX                                                     0x24

		# tRAS(min): Minimum time between activate and precharge to the same bank.
    #  For configurations with MEMC_FREQ_RATIO=2, 1T mode, program this to tRA
    # S(min)/2. No rounding up. For configurations with MEMC_FREQ_RATIO=2, 2T
    # mode or LPDDR4 mode, program this to (tRAS(min)/2) and round it up to th
    # e next integer value. Unit: Clocks
		# PSU_DDRC_DRAMTMG0_T_RAS_MIN                                                     0x12

		# SDRAM Timing Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070100, 0x7F3F7F3FU ,0x11102412U)  */
    mask_write 0XFD070100 0x7F3F7F3F 0x11102412
		# Register : DRAMTMG1 @ 0XFD070104</p>

		# tXP: Minimum time after power-down exit to any operation. For DDR3, this
    #  should be programmed to tXPDLL if slow powerdown exit is selected in MR
    # 0[12]. If C/A parity for DDR4 is used, set to (tXP+PL) instead. For conf
    # igurations with MEMC_FREQ_RATIO=2, program this to (tXP/2) and round it
    # up to the next integer value. Units: Clocks
		# PSU_DDRC_DRAMTMG1_T_XP                                                          0x4

		# tRTP: Minimum time from read to precharge of same bank. - DDR2: tAL + BL
    # /2 + max(tRTP, 2) - 2 - DDR3: tAL + max (tRTP, 4) - DDR4: Max of followi
    # ng two equations: tAL + max (tRTP, 4) or, RL + BL/2 - tRP. - mDDR: BL/2
    # - LPDDR2: Depends on if it's LPDDR2-S2 or LPDDR2-S4: LPDDR2-S2: BL/2 + t
    # RTP - 1. LPDDR2-S4: BL/2 + max(tRTP,2) - 2. - LPDDR3: BL/2 + max(tRTP,4)
    #  - 4 - LPDDR4: BL/2 + max(tRTP,8) - 8 For configurations with MEMC_FREQ_
    # RATIO=2, 1T mode, divide the above value by 2. No rounding up. For confi
    # gurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the abo
    # ve value by 2 and round it up to the next integer value. Unit: Clocks.
		# PSU_DDRC_DRAMTMG1_RD2PRE                                                        0x4

		# tRC: Minimum time between activates to same bank. For configurations wit
    # h MEMC_FREQ_RATIO=2, program this to (tRC/2) and round up to next intege
    # r value. Unit: Clocks.
		# PSU_DDRC_DRAMTMG1_T_RC                                                          0x1a

		# SDRAM Timing Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070104, 0x001F1F7FU ,0x0004041AU)  */
    mask_write 0XFD070104 0x001F1F7F 0x0004041A
		# Register : DRAMTMG2 @ 0XFD070108</p>

		# Set to WL Time from write command to write data on SDRAM interface. This
    #  must be set to WL. For mDDR, it should normally be set to 1. Note that,
    #  depending on the PHY, if using RDIMM, it may be necessary to use a valu
    # e of WL + 1 to compensate for the extra cycle of latency through the RDI
    # MM For configurations with MEMC_FREQ_RATIO=2, divide the value calculate
    # d using the above equation by 2, and round it up to next integer. This r
    # egister field is not required for DDR2 and DDR3 (except if MEMC_TRAINING
    #  is set), as the DFI read and write latencies defined in DFITMG0 and DFI
    # TMG1 are sufficient for those protocols Unit: clocks
		# PSU_DDRC_DRAMTMG2_WRITE_LATENCY                                                 0x7

		# Set to RL Time from read command to read data on SDRAM interface. This m
    # ust be set to RL. Note that, depending on the PHY, if using RDIMM, it ma
    # t be necessary to use a value of RL + 1 to compensate for the extra cycl
    # e of latency through the RDIMM For configurations with MEMC_FREQ_RATIO=2
    # , divide the value calculated using the above equation by 2, and round i
    # t up to next integer. This register field is not required for DDR2 and D
    # DR3 (except if MEMC_TRAINING is set), as the DFI read and write latencie
    # s defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit
    # : clocks
		# PSU_DDRC_DRAMTMG2_READ_LATENCY                                                  0x8

		# DDR2/3/mDDR: RL + BL/2 + 2 - WL DDR4: RL + BL/2 + 1 + WR_PREAMBLE - WL L
    # PDDR2/LPDDR3: RL + BL/2 + RU(tDQSCKmax/tCK) + 1 - WL LPDDR4(DQ ODT is Di
    # sabled): RL + BL/2 + RU(tDQSCKmax/tCK) + WR_PREAMBLE + RD_POSTAMBLE - WL
    #  LPDDR4(DQ ODT is Enabled) : RL + BL/2 + RU(tDQSCKmax/tCK) + RD_POSTAMBL
    # E - ODTLon - RU(tODTon(min)/tCK) Minimum time from read command to write
    #  command. Include time for bus turnaround and all per-bank, per-rank, an
    # d global constraints. Unit: Clocks. Where: - WL = write latency - BL = b
    # urst length. This must match the value programmed in the BL bit of the m
    # ode register to the SDRAM - RL = read latency = CAS latency - WR_PREAMBL
    # E = write preamble. This is unique to DDR4 and LPDDR4. - RD_POSTAMBLE =
    # read postamble. This is unique to LPDDR4. For LPDDR2/LPDDR3/LPDDR4, if d
    # erating is enabled (DERATEEN.derate_enable=1), derated tDQSCKmax should
    # be used. For configurations with MEMC_FREQ_RATIO=2, divide the value cal
    # culated using the above equation by 2, and round it up to next integer.
		# PSU_DDRC_DRAMTMG2_RD2WR                                                         0x6

		# DDR4: CWL + PL + BL/2 + tWTR_L Others: CWL + BL/2 + tWTR In DDR4, minimu
    # m time from write command to read command for same bank group. In others
    # , minimum time from write command to read command. Includes time for bus
    #  turnaround, recovery times, and all per-bank, per-rank, and global cons
    # traints. Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity la
    # tency - BL = burst length. This must match the value programmed in the B
    # L bit of the mode register to the SDRAM - tWTR_L = internal write to rea
    # d command delay for same bank group. This comes directly from the SDRAM
    # specification. - tWTR = internal write to read command delay. This comes
    #  directly from the SDRAM specification. Add one extra cycle for LPDDR2/L
    # PDDR3/LPDDR4 operation. For configurations with MEMC_FREQ_RATIO=2, divid
    # e the value calculated using the above equation by 2, and round it up to
    #  next integer.
		# PSU_DDRC_DRAMTMG2_WR2RD                                                         0xd

		# SDRAM Timing Register 2
		#(OFFSET, MASK, VALUE)      (0XFD070108, 0x3F3F3F3FU ,0x0708060DU)  */
    mask_write 0XFD070108 0x3F3F3F3F 0x0708060D
		# Register : DRAMTMG3 @ 0XFD07010C</p>

		# Time to wait after a mode register write or read (MRW or MRR). Present o
    # nly in designs configured to support LPDDR2, LPDDR3 or LPDDR4. LPDDR2 ty
    # pically requires value of 5. LPDDR3 typically requires value of 10. LPDD
    # R4: Set this to the larger of tMRW and tMRWCKEL. For LPDDR2, this regist
    # er is used for the time from a MRW/MRR to all other commands. For LDPDR3
    # , this register is used for the time from a MRW/MRR to a MRW/MRR.
		# PSU_DDRC_DRAMTMG3_T_MRW                                                         0x5

		# tMRD: Cycles to wait after a mode register write or read. Depending on t
    # he connected SDRAM, tMRD represents: DDR2/mDDR: Time from MRS to any com
    # mand DDR3/4: Time from MRS to MRS command LPDDR2: not used LPDDR3/4: Tim
    # e from MRS to non-MRS command For configurations with MEMC_FREQ_RATIO=2,
    #  program this to (tMRD/2) and round it up to the next integer value. If
    # C/A parity for DDR4 is used, set to tMRD_PAR(tMOD+PL) instead.
		# PSU_DDRC_DRAMTMG3_T_MRD                                                         0x4

		# tMOD: Parameter used only in DDR3 and DDR4. Cycles between load mode com
    # mand and following non-load mode command. If C/A parity for DDR4 is used
    # , set to tMOD_PAR(tMOD+PL) instead. Set to tMOD if MEMC_FREQ_RATIO=1, or
    #  tMOD/2 (rounded up to next integer) if MEMC_FREQ_RATIO=2. Note that if
    # using RDIMM, depending on the PHY, it may be necessary to use a value of
    #  tMOD + 1 or (tMOD + 1)/2 to compensate for the extra cycle of latency a
    # pplied to mode register writes by the RDIMM chip.
		# PSU_DDRC_DRAMTMG3_T_MOD                                                         0xc

		# SDRAM Timing Register 3
		#(OFFSET, MASK, VALUE)      (0XFD07010C, 0x3FF3F3FFU ,0x0050400CU)  */
    mask_write 0XFD07010C 0x3FF3F3FF 0x0050400C
		# Register : DRAMTMG4 @ 0XFD070110</p>

		# tRCD - tAL: Minimum time from activate to read or write command to same
    # bank. For configurations with MEMC_FREQ_RATIO=2, program this to ((tRCD
    # - tAL)/2) and round it up to the next integer value. Minimum value allow
    # ed for this register is 1, which implies minimum (tRCD - tAL) value to b
    # e 2 in configurations with MEMC_FREQ_RATIO=2. Unit: Clocks.
		# PSU_DDRC_DRAMTMG4_T_RCD                                                         0x8

		# DDR4: tCCD_L: This is the minimum time between two reads or two writes f
    # or same bank group. Others: tCCD: This is the minimum time between two r
    # eads or two writes. For configurations with MEMC_FREQ_RATIO=2, program t
    # his to (tCCD_L/2 or tCCD/2) and round it up to the next integer value. U
    # nit: clocks.
		# PSU_DDRC_DRAMTMG4_T_CCD                                                         0x3

		# DDR4: tRRD_L: Minimum time between activates from bank 'a' to bank 'b' f
    # or same bank group. Others: tRRD: Minimum time between activates from ba
    # nk 'a' to bank 'b'For configurations with MEMC_FREQ_RATIO=2, program thi
    # s to (tRRD_L/2 or tRRD/2) and round it up to the next integer value. Uni
    # t: Clocks.
		# PSU_DDRC_DRAMTMG4_T_RRD                                                         0x3

		# tRP: Minimum time from precharge to activate of same bank. For MEMC_FREQ
    # _RATIO=1 configurations, t_rp should be set to RoundUp(tRP/tCK). For MEM
    # C_FREQ_RATIO=2 configurations, t_rp should be set to RoundDown(RoundUp(t
    # RP/tCK)/2) + 1. For MEMC_FREQ_RATIO=2 configurations in LPDDR4, t_rp sho
    # uld be set to RoundUp(RoundUp(tRP/tCK)/2). Unit: Clocks.
		# PSU_DDRC_DRAMTMG4_T_RP                                                          0x9

		# SDRAM Timing Register 4
		#(OFFSET, MASK, VALUE)      (0XFD070110, 0x1F0F0F1FU ,0x08030309U)  */
    mask_write 0XFD070110 0x1F0F0F1F 0x08030309
		# Register : DRAMTMG5 @ 0XFD070114</p>

		# This is the time before Self Refresh Exit that CK is maintained as a val
    # id clock before issuing SRX. Specifies the clock stable time before SRX.
    #  Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCK
    # EH - DDR2: 1 - DDR3: tCKSRX - DDR4: tCKSRX For configurations with MEMC_
    # FREQ_RATIO=2, program this to recommended value divided by two and round
    #  it up to next integer.
		# PSU_DDRC_DRAMTMG5_T_CKSRX                                                       0x6

		# This is the time after Self Refresh Down Entry that CK is maintained as
    # a valid clock. Specifies the clock disable delay after SRE. Recommended
    # settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL - DDR2: 1
    # - DDR3: max (10 ns, 5 tCK) - DDR4: max (10 ns, 5 tCK) For configurations
    #  with MEMC_FREQ_RATIO=2, program this to recommended value divided by tw
    # o and round it up to next integer.
		# PSU_DDRC_DRAMTMG5_T_CKSRE                                                       0x6

		# Minimum CKE low width for Self refresh or Self refresh power down entry
    # to exit timing in memory clock cycles. Recommended settings: - mDDR: tRF
    # C - LPDDR2: tCKESR - LPDDR3: tCKESR - LPDDR4: max(tCKELPD, tSR) - DDR2:
    # tCKE - DDR3: tCKE + 1 - DDR4: tCKE + 1 For configurations with MEMC_FREQ
    # _RATIO=2, program this to recommended value divided by two and round it
    # up to next integer.
		# PSU_DDRC_DRAMTMG5_T_CKESR                                                       0x4

		# Minimum number of cycles of CKE HIGH/LOW during power-down and self refr
    # esh. - LPDDR2/LPDDR3 mode: Set this to the larger of tCKE or tCKESR - LP
    # DDR4 mode: Set this to the larger of tCKE, tCKELPD or tSR. - Non-LPDDR2/
    # non-LPDDR3/non-LPDDR4 designs: Set this to tCKE value. For configuration
    # s with MEMC_FREQ_RATIO=2, program this to (value described above)/2 and
    # round it up to the next integer value. Unit: Clocks.
		# PSU_DDRC_DRAMTMG5_T_CKE                                                         0x3

		# SDRAM Timing Register 5
		#(OFFSET, MASK, VALUE)      (0XFD070114, 0x0F0F3F1FU ,0x06060403U)  */
    mask_write 0XFD070114 0x0F0F3F1F 0x06060403
		# Register : DRAMTMG6 @ 0XFD070118</p>

		# This is the time after Deep Power Down Entry that CK is maintained as a
    # valid clock. Specifies the clock disable delay after DPDE. Recommended s
    # ettings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_
    # FREQ_RATIO=2, program this to recommended value divided by two and round
    #  it up to next integer. This is only present for designs supporting mDDR
    #  or LPDDR2/LPDDR3 devices.
		# PSU_DDRC_DRAMTMG6_T_CKDPDE                                                      0x1

		# This is the time before Deep Power Down Exit that CK is maintained as a
    # valid clock before issuing DPDX. Specifies the clock stable time before
    # DPDX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 For config
    # urations with MEMC_FREQ_RATIO=2, program this to recommended value divid
    # ed by two and round it up to next integer. This is only present for desi
    # gns supporting mDDR or LPDDR2 devices.
		# PSU_DDRC_DRAMTMG6_T_CKDPDX                                                      0x1

		# This is the time before Clock Stop Exit that CK is maintained as a valid
    #  clock before issuing Clock Stop Exit. Specifies the clock stable time b
    # efore next command after Clock Stop Exit. Recommended settings: - mDDR:
    # 1 - LPDDR2: tXP + 2 - LPDDR3: tXP + 2 - LPDDR4: tXP + 2 For configuratio
    # ns with MEMC_FREQ_RATIO=2, program this to recommended value divided by
    # two and round it up to next integer. This is only present for designs su
    # pporting mDDR or LPDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_DRAMTMG6_T_CKCSX                                                       0x4

		# SDRAM Timing Register 6
		#(OFFSET, MASK, VALUE)      (0XFD070118, 0x0F0F000FU ,0x01010004U)  */
    mask_write 0XFD070118 0x0F0F000F 0x01010004
		# Register : DRAMTMG7 @ 0XFD07011C</p>

		# This is the time after Power Down Entry that CK is maintained as a valid
    #  clock. Specifies the clock disable delay after PDE. Recommended setting
    # s: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL For configuration
    # s with MEMC_FREQ_RATIO=2, program this to recommended value divided by t
    # wo and round it up to next integer. This is only present for designs sup
    # porting mDDR or LPDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_DRAMTMG7_T_CKPDE                                                       0x6

		# This is the time before Power Down Exit that CK is maintained as a valid
    #  clock before issuing PDX. Specifies the clock stable time before PDX. R
    # ecommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: 2 For c
    # onfigurations with MEMC_FREQ_RATIO=2, program this to recommended value
    # divided by two and round it up to next integer. This is only present for
    #  designs supporting mDDR or LPDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_DRAMTMG7_T_CKPDX                                                       0x6

		# SDRAM Timing Register 7
		#(OFFSET, MASK, VALUE)      (0XFD07011C, 0x00000F0FU ,0x00000606U)  */
    mask_write 0XFD07011C 0x00000F0F 0x00000606
		# Register : DRAMTMG8 @ 0XFD070120</p>

		# tXS_FAST: Exit Self Refresh to ZQCL, ZQCS and MRS (only CL, WR, RTP and
    # Geardown mode). For configurations with MEMC_FREQ_RATIO=2, program this
    # to the above value divided by 2 and round up to next integer value. Unit
    # : Multiples of 32 clocks. Note: This is applicable to only ZQCL/ZQCS com
    # mands. Note: Ensure this is less than or equal to t_xs_x32.
		# PSU_DDRC_DRAMTMG8_T_XS_FAST_X32                                                 0x3

		# tXS_ABORT: Exit Self Refresh to commands not requiring a locked DLL in S
    # elf Refresh Abort. For configurations with MEMC_FREQ_RATIO=2, program th
    # is to the above value divided by 2 and round up to next integer value. U
    # nit: Multiples of 32 clocks. Note: Ensure this is less than or equal to
    # t_xs_x32.
		# PSU_DDRC_DRAMTMG8_T_XS_ABORT_X32                                                0x3

		# tXSDLL: Exit Self Refresh to commands requiring a locked DLL. For config
    # urations with MEMC_FREQ_RATIO=2, program this to the above value divided
    #  by 2 and round up to next integer value. Unit: Multiples of 32 clocks.
    # Note: Used only for DDR2, DDR3 and DDR4 SDRAMs.
		# PSU_DDRC_DRAMTMG8_T_XS_DLL_X32                                                  0xd

		# tXS: Exit Self Refresh to commands not requiring a locked DLL. For confi
    # gurations with MEMC_FREQ_RATIO=2, program this to the above value divide
    # d by 2 and round up to next integer value. Unit: Multiples of 32 clocks.
    #  Note: Used only for DDR2, DDR3 and DDR4 SDRAMs.
		# PSU_DDRC_DRAMTMG8_T_XS_X32                                                      0x6

		# SDRAM Timing Register 8
		#(OFFSET, MASK, VALUE)      (0XFD070120, 0x7F7F7F7FU ,0x03030D06U)  */
    mask_write 0XFD070120 0x7F7F7F7F 0x03030D06
		# Register : DRAMTMG9 @ 0XFD070124</p>

		# DDR4 Write preamble mode - 0: 1tCK preamble - 1: 2tCK preamble Present o
    # nly with MEMC_FREQ_RATIO=2
		# PSU_DDRC_DRAMTMG9_DDR4_WR_PREAMBLE                                              0x0

		# tCCD_S: This is the minimum time between two reads or two writes for dif
    # ferent bank group. For bank switching (from bank 'a' to bank 'b'), the m
    # inimum time is this value + 1. For configurations with MEMC_FREQ_RATIO=2
    # , program this to (tCCD_S/2) and round it up to the next integer value.
    # Present only in designs configured to support DDR4. Unit: clocks.
		# PSU_DDRC_DRAMTMG9_T_CCD_S                                                       0x2

		# tRRD_S: Minimum time between activates from bank 'a' to bank 'b' for dif
    # ferent bank group. For configurations with MEMC_FREQ_RATIO=2, program th
    # is to (tRRD_S/2) and round it up to the next integer value. Present only
    #  in designs configured to support DDR4. Unit: Clocks.
		# PSU_DDRC_DRAMTMG9_T_RRD_S                                                       0x2

		# CWL + PL + BL/2 + tWTR_S Minimum time from write command to read command
    #  for different bank group. Includes time for bus turnaround, recovery ti
    # mes, and all per-bank, per-rank, and global constraints. Present only in
    #  designs configured to support DDR4. Unit: Clocks. Where: - CWL = CAS wr
    # ite latency - PL = Parity latency - BL = burst length. This must match t
    # he value programmed in the BL bit of the mode register to the SDRAM - tW
    # TR_S = internal write to read command delay for different bank group. Th
    # is comes directly from the SDRAM specification. For configurations with
    # MEMC_FREQ_RATIO=2, divide the value calculated using the above equation
    # by 2, and round it up to next integer.
		# PSU_DDRC_DRAMTMG9_WR2RD_S                                                       0xb

		# SDRAM Timing Register 9
		#(OFFSET, MASK, VALUE)      (0XFD070124, 0x40070F3FU ,0x0002020BU)  */
    mask_write 0XFD070124 0x40070F3F 0x0002020B
		# Register : DRAMTMG11 @ 0XFD07012C</p>

		# tXMPDLL: This is the minimum Exit MPSM to commands requiring a locked DL
    # L. For configurations with MEMC_FREQ_RATIO=2, program this to (tXMPDLL/2
    # ) and round it up to the next integer value. Present only in designs con
    # figured to support DDR4. Unit: Multiples of 32 clocks.
		# PSU_DDRC_DRAMTMG11_POST_MPSM_GAP_X32                                            0x70

		# tMPX_LH: This is the minimum CS_n Low hold time to CKE rising edge. For
    # configurations with MEMC_FREQ_RATIO=2, program this to RoundUp(tMPX_LH/2
    # )+1. Present only in designs configured to support DDR4. Unit: clocks.
		# PSU_DDRC_DRAMTMG11_T_MPX_LH                                                     0x7

		# tMPX_S: Minimum time CS setup time to CKE. For configurations with MEMC_
    # FREQ_RATIO=2, program this to (tMPX_S/2) and round it up to the next int
    # eger value. Present only in designs configured to support DDR4. Unit: Cl
    # ocks.
		# PSU_DDRC_DRAMTMG11_T_MPX_S                                                      0x1

		# tCKMPE: Minimum valid clock requirement after MPSM entry. Present only i
    # n designs configured to support DDR4. Unit: Clocks. For configurations w
    # ith MEMC_FREQ_RATIO=2, divide the value calculated using the above equat
    # ion by 2, and round it up to next integer.
		# PSU_DDRC_DRAMTMG11_T_CKMPE                                                      0xe

		# SDRAM Timing Register 11
		#(OFFSET, MASK, VALUE)      (0XFD07012C, 0x7F1F031FU ,0x7007010EU)  */
    mask_write 0XFD07012C 0x7F1F031F 0x7007010E
		# Register : DRAMTMG12 @ 0XFD070130</p>

		# tCMDCKE: Delay from valid command to CKE input LOW. Set this to the larg
    # er of tESCKE or tCMDCKE For configurations with MEMC_FREQ_RATIO=2, progr
    # am this to (max(tESCKE, tCMDCKE)/2) and round it up to next integer valu
    # e.
		# PSU_DDRC_DRAMTMG12_T_CMDCKE                                                     0x2

		# tCKEHCMD: Valid command requirement after CKE input HIGH. For configurat
    # ions with MEMC_FREQ_RATIO=2, program this to (tCKEHCMD/2) and round it u
    # p to next integer value.
		# PSU_DDRC_DRAMTMG12_T_CKEHCMD                                                    0x6

		# tMRD_PDA: This is the Mode Register Set command cycle time in PDA mode.
    # For configurations with MEMC_FREQ_RATIO=2, program this to (tMRD_PDA/2)
    # and round it up to next integer value.
		# PSU_DDRC_DRAMTMG12_T_MRD_PDA                                                    0x8

		# SDRAM Timing Register 12
		#(OFFSET, MASK, VALUE)      (0XFD070130, 0x00030F1FU ,0x00020608U)  */
    mask_write 0XFD070130 0x00030F1F 0x00020608
		# Register : ZQCTL0 @ 0XFD070180</p>

		# - 1 - Disable uMCTL2 generation of ZQCS/MPC(ZQ calibration) command. Reg
    # ister DBGCMD.zq_calib_short can be used instead to issue ZQ calibration
    # request from APB module. - 0 - Internally generate ZQCS/MPC(ZQ calibrati
    # on) commands based on ZQCTL1.t_zq_short_interval_x1024. This is only pre
    # sent for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_ZQCTL0_DIS_AUTO_ZQ                                                     0x1

		# - 1 - Disable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refres
    # h/SR-Powerdown exit. Only applicable when run in DDR3 or DDR4 or LPDDR2
    # or LPDDR3 or LPDDR4 mode. - 0 - Enable issuing of ZQCL/MPC(ZQ calibratio
    # n) command at Self-Refresh/SR-Powerdown exit. Only applicable when run i
    # n DDR3 or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. This is only present
    # for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_ZQCTL0_DIS_SRX_ZQCL                                                    0x0

		# - 1 - Denotes that ZQ resistor is shared between ranks. Means ZQinit/ZQC
    # L/ZQCS/MPC(ZQ calibration) commands are sent to one rank at a time with
    # tZQinit/tZQCL/tZQCS/tZQCAL/tZQLAT timing met between commands so that co
    # mmands to different ranks do not overlap. - 0 - ZQ resistor is not share
    # d. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR
    # 3/LPDDR4 devices.
		# PSU_DDRC_ZQCTL0_ZQ_RESISTOR_SHARED                                              0x0

		# - 1 - Disable issuing of ZQCL command at Maximum Power Saving Mode exit.
    #  Only applicable when run in DDR4 mode. - 0 - Enable issuing of ZQCL com
    # mand at Maximum Power Saving Mode exit. Only applicable when run in DDR4
    #  mode. This is only present for designs supporting DDR4 devices.
		# PSU_DDRC_ZQCTL0_DIS_MPSMX_ZQCL                                                  0x0

		# tZQoper for DDR3/DDR4, tZQCL for LPDDR2/LPDDR3, tZQCAL for LPDDR4: Numbe
    # r of cycles of NOP required after a ZQCL (ZQ calibration long)/MPC(ZQ St
    # art) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO
    # =2: DDR3/DDR4: program this to tZQoper/2 and round it up to the next int
    # eger value. LPDDR2/LPDDR3: program this to tZQCL/2 and round it up to th
    # e next integer value. LPDDR4: program this to tZQCAL/2 and round it up t
    # o the next integer value. Unit: Clock cycles. This is only present for d
    # esigns supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_ZQCTL0_T_ZQ_LONG_NOP                                                   0x100

		# tZQCS for DDR3/DD4/LPDDR2/LPDDR3, tZQLAT for LPDDR4: Number of cycles of
    #  NOP required after a ZQCS (ZQ calibration short)/MPC(ZQ Latch) command
    # is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2, program t
    # his to tZQCS/2 and round it up to the next integer value. Unit: Clock cy
    # cles. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LP
    # DDR3/LPDDR4 devices.
		# PSU_DDRC_ZQCTL0_T_ZQ_SHORT_NOP                                                  0x40

		# ZQ Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070180, 0xF7FF03FFU ,0x81000040U)  */
    mask_write 0XFD070180 0xF7FF03FF 0x81000040
		# Register : ZQCTL1 @ 0XFD070184</p>

		# tZQReset: Number of cycles of NOP required after a ZQReset (ZQ calibrati
    # on Reset) command is issued to SDRAM. For configurations with MEMC_FREQ_
    # RATIO=2, program this to tZQReset/2 and round it up to the next integer
    # value. Unit: Clock cycles. This is only present for designs supporting L
    # PDDR2/LPDDR3/LPDDR4 devices.
		# PSU_DDRC_ZQCTL1_T_ZQ_RESET_NOP                                                  0x20

		# Average interval to wait between automatically issuing ZQCS (ZQ calibrat
    # ion short)/MPC(ZQ calibration) commands to DDR3/DDR4/LPDDR2/LPDDR3/LPDDR
    # 4 devices. Meaningless, if ZQCTL0.dis_auto_zq=1. Unit: 1024 clock cycles
    # . This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3
    # /LPDDR4 devices.
		# PSU_DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024                                       0x196dc

		# ZQ Control Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070184, 0x3FFFFFFFU ,0x020196DCU)  */
    mask_write 0XFD070184 0x3FFFFFFF 0x020196DC
		# Register : DFITMG0 @ 0XFD070190</p>

		# Specifies the number of DFI clock cycles after an assertion or de-assert
    # ion of the DFI control signals that the control signals at the PHY-DRAM
    # interface reflect the assertion or de-assertion. If the DFI clock and th
    # e memory clock are not phase-aligned, this timing parameter should be ro
    # unded up to the next integer value. Note that if using RDIMM, it is nece
    # ssary to increment this parameter by RDIMM's extra cycle of latency in t
    # erms of DFI clock.
		# PSU_DDRC_DFITMG0_DFI_T_CTRL_DELAY                                               0x4

		# Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated u
    # sing HDR or SDR values Selects whether value in DFITMG0.dfi_t_rddata_en
    # is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles
    #  - 1 in terms of SDR clock cycles Refer to PHY specification for correct
    #  value.
		# PSU_DDRC_DFITMG0_DFI_RDDATA_USE_SDR                                             0x1

		# Time from the assertion of a read command on the DFI interface to the as
    # sertion of the dfi_rddata_en signal. Refer to PHY specification for corr
    # ect value. This corresponds to the DFI parameter trddata_en. Note that,
    # depending on the PHY, if using RDIMM, it may be necessary to use the val
    # ue (CL + 1) in the calculation of trddata_en. This is to compensate for
    # the extra cycle of latency through the RDIMM. Unit: Clocks
		# PSU_DDRC_DFITMG0_DFI_T_RDDATA_EN                                                0xb

		# Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated us
    # ing HDR or SDR values Selects whether value in DFITMG0.dfi_tphy_wrlat is
    #  in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.df
    # i_tphy_wrdata is in terms of SDR or HDR clock cycles - 0 in terms of HDR
    #  clock cycles - 1 in terms of SDR clock cycles Refer to PHY specificatio
    # n for correct value.
		# PSU_DDRC_DFITMG0_DFI_WRDATA_USE_SDR                                             0x1

		# Specifies the number of clock cycles between when dfi_wrdata_en is asser
    # ted to when the associated write data is driven on the dfi_wrdata signal
    # . This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY
    #  specification for correct value. Note, max supported value is 8. Unit:
    # Clocks
		# PSU_DDRC_DFITMG0_DFI_TPHY_WRDATA                                                0x2

		# Write latency Number of clocks from the write command to write data enab
    # le (dfi_wrdata_en). This corresponds to the DFI timing parameter tphy_wr
    # lat. Refer to PHY specification for correct value.Note that, depending o
    # n the PHY, if using RDIMM, it may be necessary to use the value (CL + 1)
    #  in the calculation of tphy_wrlat. This is to compensate for the extra c
    # ycle of latency through the RDIMM.
		# PSU_DDRC_DFITMG0_DFI_TPHY_WRLAT                                                 0xb

		# DFI Timing Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070190, 0x1FBFBF3FU ,0x048B820BU)  */
    mask_write 0XFD070190 0x1FBFBF3F 0x048B820B
		# Register : DFITMG1 @ 0XFD070194</p>

		# Specifies the number of DFI PHY clocks between when the dfi_cs signal is
    #  asserted and when the associated command is driven. This field is used
    # for CAL mode, should be set to '0' or the value which matches the CAL mo
    # de register setting in the DRAM. If the PHY can add the latency for CAL
    # mode, this should be set to '0'. Valid Range: 0, 3, 4, 5, 6, and 8
		# PSU_DDRC_DFITMG1_DFI_T_CMD_LAT                                                  0x0

		# Specifies the number of DFI PHY clocks between when the dfi_cs signal is
    #  asserted and when the associated dfi_parity_in signal is driven.
		# PSU_DDRC_DFITMG1_DFI_T_PARIN_LAT                                                0x0

		# Specifies the number of DFI clocks between when the dfi_wrdata_en signal
    #  is asserted and when the corresponding write data transfer is completed
    #  on the DRAM bus. This corresponds to the DFI timing parameter twrdata_d
    # elay. Refer to PHY specification for correct value. For DFI 3.0 PHY, set
    #  to twrdata_delay, a new timing parameter introduced in DFI 3.0. For DFI
    #  2.1 PHY, set to tphy_wrdata + (delay of DFI write data to the DRAM). Va
    # lue to be programmed is in terms of DFI clocks, not PHY clocks. In FREQ_
    # RATIO=2, divide PHY's value by 2 and round up to next integer. If using
    # DFITMG0.dfi_wrdata_use_sdr=1, add 1 to the value. Unit: Clocks
		# PSU_DDRC_DFITMG1_DFI_T_WRDATA_DELAY                                             0x3

		# Specifies the number of DFI clock cycles from the assertion of the dfi_d
    # ram_clk_disable signal on the DFI until the clock to the DRAM memory dev
    # ices, at the PHY-DRAM boundary, maintains a low value. If the DFI clock
    # and the memory clock are not phase aligned, this timing parameter should
    #  be rounded up to the next integer value.
		# PSU_DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE                                         0x3

		# Specifies the number of DFI clock cycles from the de-assertion of the df
    # i_dram_clk_disable signal on the DFI until the first valid rising edge o
    # f the clock to the DRAM memory devices, at the PHY-DRAM boundary. If the
    #  DFI clock and the memory clock are not phase aligned, this timing param
    # eter should be rounded up to the next integer value.
		# PSU_DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE                                          0x4

		# DFI Timing Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070194, 0xF31F0F0FU ,0x00030304U)  */
    mask_write 0XFD070194 0xF31F0F0F 0x00030304
		# Register : DFILPCFG0 @ 0XFD070198</p>

		# Setting for DFI's tlp_resp time. Same value is used for both Power Down,
    #  Self Refresh, Deep Power Down and Maximum Power Saving modes. DFI 2.1 s
    # pecification onwards, recommends using a fixed value of 7 always.
		# PSU_DDRC_DFILPCFG0_DFI_TLP_RESP                                                 0x7

		# Value to drive on dfi_lp_wakeup signal when Deep Power Down mode is ente
    # red. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycles - 0x1 - 32
    # cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 5
    # 12 cycles - 0x6 - 1024 cycles - 0x7 - 2048 cycles - 0x8 - 4096 cycles -
    # 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 6553
    # 6 cycles - 0xD - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimited T
    # his is only present for designs supporting mDDR or LPDDR2/LPDDR3 devices
    # .
		# PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD                                            0x0

		# Enables DFI Low Power interface handshaking during Deep Power Down Entry
    # /Exit. - 0 - Disabled - 1 - Enabled This is only present for designs sup
    # porting mDDR or LPDDR2/LPDDR3 devices.
		# PSU_DDRC_DFILPCFG0_DFI_LP_EN_DPD                                                0x0

		# Value to drive on dfi_lp_wakeup signal when Self Refresh mode is entered
    # . Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycles - 0x1 - 32 cyc
    # les - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512
    # cycles - 0x6 - 1024 cycles - 0x7 - 2048 cycles - 0x8 - 4096 cycles - 0x9
    #  - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 c
    # ycles - 0xD - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimited
		# PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR                                             0x0

		# Enables DFI Low Power interface handshaking during Self Refresh Entry/Ex
    # it. - 0 - Disabled - 1 - Enabled
		# PSU_DDRC_DFILPCFG0_DFI_LP_EN_SR                                                 0x1

		# Value to drive on dfi_lp_wakeup signal when Power Down mode is entered.
    # Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycles - 0x1 - 32 cycle
    # s - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cy
    # cles - 0x6 - 1024 cycles - 0x7 - 2048 cycles - 0x8 - 4096 cycles - 0x9 -
    #  8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cyc
    # les - 0xD - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimited
		# PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD                                             0x0

		# Enables DFI Low Power interface handshaking during Power Down Entry/Exit
    # . - 0 - Disabled - 1 - Enabled
		# PSU_DDRC_DFILPCFG0_DFI_LP_EN_PD                                                 0x1

		# DFI Low Power Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070198, 0x0FF1F1F1U ,0x07000101U)  */
    mask_write 0XFD070198 0x0FF1F1F1 0x07000101
		# Register : DFILPCFG1 @ 0XFD07019C</p>

		# Value to drive on dfi_lp_wakeup signal when Maximum Power Saving Mode is
    #  entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycles - 0x1
    # - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x
    # 5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 2048 cycles - 0x8 - 4096 cycl
    # es - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC -
    #  65536 cycles - 0xD - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimi
    # ted This is only present for designs supporting DDR4 devices.
		# PSU_DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM                                           0x2

		# Enables DFI Low Power interface handshaking during Maximum Power Saving
    # Mode Entry/Exit. - 0 - Disabled - 1 - Enabled This is only present for d
    # esigns supporting DDR4 devices.
		# PSU_DDRC_DFILPCFG1_DFI_LP_EN_MPSM                                               0x1

		# DFI Low Power Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD07019C, 0x000000F1U ,0x00000021U)  */
    mask_write 0XFD07019C 0x000000F1 0x00000021
		# Register : DFIUPD0 @ 0XFD0701A0</p>

		# When '1', disable the automatic dfi_ctrlupd_req generation by the uMCTL2
    # . The core must issue the dfi_ctrlupd_req signal using register reg_ddrc
    # _ctrlupd. When '0', uMCTL2 issues dfi_ctrlupd_req periodically.
		# PSU_DDRC_DFIUPD0_DIS_AUTO_CTRLUPD                                               0x0

		# When '1', disable the automatic dfi_ctrlupd_req generation by the uMCTL2
    #  following a self-refresh exit. The core must issue the dfi_ctrlupd_req
    # signal using register reg_ddrc_ctrlupd. When '0', uMCTL2 issues a dfi_ct
    # rlupd_req after exiting self-refresh.
		# PSU_DDRC_DFIUPD0_DIS_AUTO_CTRLUPD_SRX                                           0x0

		# Specifies the maximum number of clock cycles that the dfi_ctrlupd_req si
    # gnal can assert. Lowest value to assign to this variable is 0x40. Unit:
    # Clocks
		# PSU_DDRC_DFIUPD0_DFI_T_CTRLUP_MAX                                               0x40

		# Specifies the minimum number of clock cycles that the dfi_ctrlupd_req si
    # gnal must be asserted. The uMCTL2 expects the PHY to respond within this
    #  time. If the PHY does not respond, the uMCTL2 will de-assert dfi_ctrlup
    # d_req after dfi_t_ctrlup_min + 2 cycles. Lowest value to assign to this
    # variable is 0x3. Unit: Clocks
		# PSU_DDRC_DFIUPD0_DFI_T_CTRLUP_MIN                                               0x3

		# DFI Update Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0701A0, 0xC3FF03FFU ,0x00400003U)  */
    mask_write 0XFD0701A0 0xC3FF03FF 0x00400003
		# Register : DFIUPD1 @ 0XFD0701A4</p>

		# This is the minimum amount of time between uMCTL2 initiated DFI update r
    # equests (which is executed whenever the uMCTL2 is idle). Set this number
    #  higher to reduce the frequency of update requests, which can have a sma
    # ll impact on the latency of the first read request when the uMCTL2 is id
    # le. Unit: 1024 clocks
		# PSU_DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024                               0x41

		# This is the maximum amount of time between uMCTL2 initiated DFI update r
    # equests. This timer resets with each update request; when the timer expi
    # res dfi_ctrlupd_req is sent and traffic is blocked until the dfi_ctrlupd
    # _ackx is received. PHY can use this idle time to recalibrate the delay l
    # ines to the DLLs. The DFI controller update is also used to reset PHY FI
    # FO pointers in case of data capture errors. Updates are required to main
    # tain calibration over PVT, but frequent updates may impact performance.
    # Note: Value programmed for DFIUPD1.dfi_t_ctrlupd_interval_max_x1024 must
    #  be greater than DFIUPD1.dfi_t_ctrlupd_interval_min_x1024. Unit: 1024 cl
    # ocks
		# PSU_DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024                               0xe1

		# DFI Update Register 1
		#(OFFSET, MASK, VALUE)      (0XFD0701A4, 0x00FF00FFU ,0x004100E1U)  */
    mask_write 0XFD0701A4 0x00FF00FF 0x004100E1
		# Register : DFIMISC @ 0XFD0701B0</p>

		# Defines polarity of dfi_wrdata_cs and dfi_rddata_cs signals. - 0: Signal
    # s are active low - 1: Signals are active high
		# PSU_DDRC_DFIMISC_DFI_DATA_CS_POLARITY                                           0x0

		# DBI implemented in DDRC or PHY. - 0 - DDRC implements DBI functionality.
    #  - 1 - PHY implements DBI functionality. Present only in designs configu
    # red to support DDR4 and LPDDR4.
		# PSU_DDRC_DFIMISC_PHY_DBI_MODE                                                   0x0

		# PHY initialization complete enable signal. When asserted the dfi_init_co
    # mplete signal can be used to trigger SDRAM initialisation
		# PSU_DDRC_DFIMISC_DFI_INIT_COMPLETE_EN                                           0x0

		# DFI Miscellaneous Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0701B0, 0x00000007U ,0x00000000U)  */
    mask_write 0XFD0701B0 0x00000007 0x00000000
		# Register : DFITMG2 @ 0XFD0701B4</p>

		# >Number of clocks between when a read command is sent on the DFI control
    #  interface and when the associated dfi_rddata_cs signal is asserted. Thi
    # s corresponds to the DFI timing parameter tphy_rdcslat. Refer to PHY spe
    # cification for correct value.
		# PSU_DDRC_DFITMG2_DFI_TPHY_RDCSLAT                                               0x9

		# Number of clocks between when a write command is sent on the DFI control
    #  interface and when the associated dfi_wrdata_cs signal is asserted. Thi
    # s corresponds to the DFI timing parameter tphy_wrcslat. Refer to PHY spe
    # cification for correct value.
		# PSU_DDRC_DFITMG2_DFI_TPHY_WRCSLAT                                               0x6

		# DFI Timing Register 2
		#(OFFSET, MASK, VALUE)      (0XFD0701B4, 0x00003F3FU ,0x00000906U)  */
    mask_write 0XFD0701B4 0x00003F3F 0x00000906
		# Register : DBICTL @ 0XFD0701C0</p>

		# Read DBI enable signal in DDRC. - 0 - Read DBI is disabled. - 1 - Read D
    # BI is enabled. This signal must be set the same value as DRAM's mode reg
    # ister. - DDR4: MR5 bit A12. When x4 devices are used, this signal must b
    # e set to 0. - LPDDR4: MR3[6]
		# PSU_DDRC_DBICTL_RD_DBI_EN                                                       0x0

		# Write DBI enable signal in DDRC. - 0 - Write DBI is disabled. - 1 - Writ
    # e DBI is enabled. This signal must be set the same value as DRAM's mode
    # register. - DDR4: MR5 bit A11. When x4 devices are used, this signal mus
    # t be set to 0. - LPDDR4: MR3[7]
		# PSU_DDRC_DBICTL_WR_DBI_EN                                                       0x0

		# DM enable signal in DDRC. - 0 - DM is disabled. - 1 - DM is enabled. Thi
    # s signal must be set the same logical value as DRAM's mode register. - D
    # DR4: Set this to same value as MR5 bit A10. When x4 devices are used, th
    # is signal must be set to 0. - LPDDR4: Set this to inverted value of MR13
    # [5] which is opposite polarity from this signal
		# PSU_DDRC_DBICTL_DM_EN                                                           0x1

		# DM/DBI Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0701C0, 0x00000007U ,0x00000001U)  */
    mask_write 0XFD0701C0 0x00000007 0x00000001
		# Register : ADDRMAP0 @ 0XFD070200</p>

		# Selects the HIF address bit used as rank address bit 0. Valid Range: 0 t
    # o 27, and 31 Internal Base: 6 The selected HIF address bit is determined
    #  by adding the internal base to the value of this field. If set to 31, r
    # ank address bit 0 is set to 0.
		# PSU_DDRC_ADDRMAP0_ADDRMAP_CS_BIT0                                               0x1f

		# Address Map Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070200, 0x0000001FU ,0x0000001FU)  */
    mask_write 0XFD070200 0x0000001F 0x0000001F
		# Register : ADDRMAP1 @ 0XFD070204</p>

		# Selects the HIF address bit used as bank address bit 2. Valid Range: 0 t
    # o 29 and 31 Internal Base: 4 The selected HIF address bit is determined
    # by adding the internal base to the value of this field. If set to 31, ba
    # nk address bit 2 is set to 0.
		# PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B2                                               0x1f

		# Selects the HIF address bits used as bank address bit 1. Valid Range: 0
    # to 30 Internal Base: 3 The selected HIF address bit for each of the bank
    #  address bits is determined by adding the internal base to the value of
    # this field.
		# PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B1                                               0xa

		# Selects the HIF address bits used as bank address bit 0. Valid Range: 0
    # to 30 Internal Base: 2 The selected HIF address bit for each of the bank
    #  address bits is determined by adding the internal base to the value of
    # this field.
		# PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B0                                               0xa

		# Address Map Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070204, 0x001F1F1FU ,0x001F0A0AU)  */
    mask_write 0XFD070204 0x001F1F1F 0x001F0A0A
		# Register : ADDRMAP2 @ 0XFD070208</p>

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 5. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 6. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 7 . Valid Range: 0 to 7, and 15 Internal Base
    # : 5 The selected HIF address bit is determined by adding the internal ba
    # se to the value of this field. If set to 15, this column address bit is
    # set to 0.
		# PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B5                                                0x0

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 4. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 5. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 6. Valid Range: 0 to 7, and 15 Internal Base:
    #  4 The selected HIF address bit is determined by adding the internal bas
    # e to the value of this field. If set to 15, this column address bit is s
    # et to 0.
		# PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B4                                                0x0

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 3. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 4. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 5. Valid Range: 0 to 7 Internal Base: 3 The s
    # elected HIF address bit is determined by adding the internal base to the
    #  value of this field. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=1
    # 6, it is required to program this to 0, hence register does not exist in
    #  this case.
		# PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B3                                                0x0

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 2. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 3. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 4. Valid Range: 0 to 7 Internal Base: 2 The s
    # elected HIF address bit is determined by adding the internal base to the
    #  value of this field. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=8
    #  or 16, it is required to program this to 0.
		# PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B2                                                0x0

		# Address Map Register 2
		#(OFFSET, MASK, VALUE)      (0XFD070208, 0x0F0F0F0FU ,0x00000000U)  */
    mask_write 0XFD070208 0x0F0F0F0F 0x00000000
		# Register : ADDRMAP3 @ 0XFD07020C</p>

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 9. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 11 (10 in LPDDR2/LPDDR3 mode). - Quarter bus width mode:
    # Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/
    # LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 9 The selected
    # HIF address bit is determined by adding the internal base to the value o
    # f this field. If set to 15, this column address bit is set to 0. Note: P
    # er JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved fo
    # r indicating auto-precharge, and hence no source address bit can be mapp
    # ed to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit
    # for auto-precharge in the CA bus and hence column bit 10 is used.
		# PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B9                                                0x0

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 8. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 9. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). Valid Range: 0
    #  to 7, and 15 Internal Base: 8 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specifi
    # cation, column address bit 10 is reserved for indicating auto-precharge,
    #  and hence no source address bit can be mapped to column address bit 10.
    #  In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA
    #  bus and hence column bit 10 is used.
		# PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B8                                                0x0

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 7. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 8. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 9. Valid Range: 0 to 7, and 15 Internal Base:
    #  7 The selected HIF address bit is determined by adding the internal bas
    # e to the value of this field. If set to 15, this column address bit is s
    # et to 0.
		# PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B7                                                0x0

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 6. - Half bus width mode: Selects the HIF address bit used as colu
    # mn address bit 7. - Quarter bus width mode: Selects the HIF address bit
    # used as column address bit 8. Valid Range: 0 to 7, and 15 Internal Base:
    #  6 The selected HIF address bit is determined by adding the internal bas
    # e to the value of this field. If set to 15, this column address bit is s
    # et to 0.
		# PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B6                                                0x0

		# Address Map Register 3
		#(OFFSET, MASK, VALUE)      (0XFD07020C, 0x0F0F0F0FU ,0x00000000U)  */
    mask_write 0XFD07020C 0x0F0F0F0F 0x00000000
		# Register : ADDRMAP4 @ 0XFD070210</p>

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 13 (11 in LPDDR2/LPDDR3 mode). - Half bus width mode: Unused. To m
    # ake it unused, this should be tied to 4'hF. - Quarter bus width mode: Un
    # used. To make it unused, this must be tied to 4'hF. Valid Range: 0 to 7,
    #  and 15 Internal Base: 11 The selected HIF address bit is determined by
    # adding the internal base to the value of this field. If set to 15, this
    # column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specificatio
    # n, column address bit 10 is reserved for indicating auto-precharge, and
    # hence no source address bit can be mapped to column address bit 10. In L
    # PDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus
    # and hence column bit 10 is used.
		# PSU_DDRC_ADDRMAP4_ADDRMAP_COL_B11                                               0xf

		# - Full bus width mode: Selects the HIF address bit used as column addres
    # s bit 11 (10 in LPDDR2/LPDDR3 mode). - Half bus width mode: Selects the
    # HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode)
    # . - Quarter bus width mode: UNUSED. To make it unused, this must be tied
    #  to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 10 The selected HIF
    #  address bit is determined by adding the internal base to the value of t
    # his field. If set to 15, this column address bit is set to 0. Note: Per
    # JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for i
    # ndicating auto-precharge, and hence no source address bit can be mapped
    # to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for
    #  auto-precharge in the CA bus and hence column bit 10 is used.
		# PSU_DDRC_ADDRMAP4_ADDRMAP_COL_B10                                               0xf

		# Address Map Register 4
		#(OFFSET, MASK, VALUE)      (0XFD070210, 0x00000F0FU ,0x00000F0FU)  */
    mask_write 0XFD070210 0x00000F0F 0x00000F0F
		# Register : ADDRMAP5 @ 0XFD070214</p>

		# Selects the HIF address bit used as row address bit 11. Valid Range: 0 t
    # o 11, and 15 Internal Base: 17 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 11 is set to 0.
		# PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B11                                               0x8

		# Selects the HIF address bits used as row address bits 2 to 10. Valid Ran
    # ge: 0 to 11, and 15 Internal Base: 8 (for row address bit 2), 9 (for row
    #  address bit 3), 10 (for row address bit 4) etc increasing to 16 (for ro
    # w address bit 10) The selected HIF address bit for each of the row addre
    # ss bits is determined by adding the internal base to the value of this f
    # ield. When value 15 is used the values of row address bits 2 to 10 are d
    # efined by registers ADDRMAP9, ADDRMAP10, ADDRMAP11.
		# PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10                                             0xf

		# Selects the HIF address bits used as row address bit 1. Valid Range: 0 t
    # o 11 Internal Base: 7 The selected HIF address bit for each of the row a
    # ddress bits is determined by adding the internal base to the value of th
    # is field.
		# PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B1                                                0x8

		# Selects the HIF address bits used as row address bit 0. Valid Range: 0 t
    # o 11 Internal Base: 6 The selected HIF address bit for each of the row a
    # ddress bits is determined by adding the internal base to the value of th
    # is field.
		# PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B0                                                0x8

		# Address Map Register 5
		#(OFFSET, MASK, VALUE)      (0XFD070214, 0x0F0F0F0FU ,0x080F0808U)  */
    mask_write 0XFD070214 0x0F0F0F0F 0x080F0808
		# Register : ADDRMAP6 @ 0XFD070218</p>

		# Set this to 1 if there is an LPDDR3 SDRAM 6Gb or 12Gb device in use. - 1
    #  - LPDDR3 SDRAM 6Gb/12Gb device in use. Every address having row[14:13]=
    # =2'b11 is considered as invalid - 0 - non-LPDDR3 6Gb/12Gb device in use.
    #  All addresses are valid Present only in designs configured to support L
    # PDDR3.
		# PSU_DDRC_ADDRMAP6_LPDDR3_6GB_12GB                                               0x0

		# Selects the HIF address bit used as row address bit 15. Valid Range: 0 t
    # o 11, and 15 Internal Base: 21 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 15 is set to 0.
		# PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B15                                               0xf

		# Selects the HIF address bit used as row address bit 14. Valid Range: 0 t
    # o 11, and 15 Internal Base: 20 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 14 is set to 0.
		# PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B14                                               0x8

		# Selects the HIF address bit used as row address bit 13. Valid Range: 0 t
    # o 11, and 15 Internal Base: 19 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 13 is set to 0.
		# PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B13                                               0x8

		# Selects the HIF address bit used as row address bit 12. Valid Range: 0 t
    # o 11, and 15 Internal Base: 18 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 12 is set to 0.
		# PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B12                                               0x8

		# Address Map Register 6
		#(OFFSET, MASK, VALUE)      (0XFD070218, 0x8F0F0F0FU ,0x0F080808U)  */
    mask_write 0XFD070218 0x8F0F0F0F 0x0F080808
		# Register : ADDRMAP7 @ 0XFD07021C</p>

		# Selects the HIF address bit used as row address bit 17. Valid Range: 0 t
    # o 10, and 15 Internal Base: 23 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 17 is set to 0.
		# PSU_DDRC_ADDRMAP7_ADDRMAP_ROW_B17                                               0xf

		# Selects the HIF address bit used as row address bit 16. Valid Range: 0 t
    # o 11, and 15 Internal Base: 22 The selected HIF address bit is determine
    # d by adding the internal base to the value of this field. If set to 15,
    # row address bit 16 is set to 0.
		# PSU_DDRC_ADDRMAP7_ADDRMAP_ROW_B16                                               0xf

		# Address Map Register 7
		#(OFFSET, MASK, VALUE)      (0XFD07021C, 0x00000F0FU ,0x00000F0FU)  */
    mask_write 0XFD07021C 0x00000F0F 0x00000F0F
		# Register : ADDRMAP8 @ 0XFD070220</p>

		# Selects the HIF address bits used as bank group address bit 1. Valid Ran
    # ge: 0 to 30, and 31 Internal Base: 3 The selected HIF address bit for ea
    # ch of the bank group address bits is determined by adding the internal b
    # ase to the value of this field. If set to 31, bank group address bit 1 i
    # s set to 0.
		# PSU_DDRC_ADDRMAP8_ADDRMAP_BG_B1                                                 0x8

		# Selects the HIF address bits used as bank group address bit 0. Valid Ran
    # ge: 0 to 30 Internal Base: 2 The selected HIF address bit for each of th
    # e bank group address bits is determined by adding the internal base to t
    # he value of this field.
		# PSU_DDRC_ADDRMAP8_ADDRMAP_BG_B0                                                 0x8

		# Address Map Register 8
		#(OFFSET, MASK, VALUE)      (0XFD070220, 0x00001F1FU ,0x00000808U)  */
    mask_write 0XFD070220 0x00001F1F 0x00000808
		# Register : ADDRMAP9 @ 0XFD070224</p>

		# Selects the HIF address bits used as row address bit 5. Valid Range: 0 t
    # o 11 Internal Base: 11 The selected HIF address bit for each of the row
    # address bits is determined by adding the internal base to the value of t
    # his field. This register field is used only when ADDRMAP5.addrmap_row_b2
    # _10 is set to value 15.
		# PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B5                                                0x8

		# Selects the HIF address bits used as row address bit 4. Valid Range: 0 t
    # o 11 Internal Base: 10 The selected HIF address bit for each of the row
    # address bits is determined by adding the internal base to the value of t
    # his field. This register field is used only when ADDRMAP5.addrmap_row_b2
    # _10 is set to value 15.
		# PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B4                                                0x8

		# Selects the HIF address bits used as row address bit 3. Valid Range: 0 t
    # o 11 Internal Base: 9 The selected HIF address bit for each of the row a
    # ddress bits is determined by adding the internal base to the value of th
    # is field. This register field is used only when ADDRMAP5.addrmap_row_b2_
    # 10 is set to value 15.
		# PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B3                                                0x8

		# Selects the HIF address bits used as row address bit 2. Valid Range: 0 t
    # o 11 Internal Base: 8 The selected HIF address bit for each of the row a
    # ddress bits is determined by adding the internal base to the value of th
    # is field. This register field is used only when ADDRMAP5.addrmap_row_b2_
    # 10 is set to value 15.
		# PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B2                                                0x8

		# Address Map Register 9
		#(OFFSET, MASK, VALUE)      (0XFD070224, 0x0F0F0F0FU ,0x08080808U)  */
    mask_write 0XFD070224 0x0F0F0F0F 0x08080808
		# Register : ADDRMAP10 @ 0XFD070228</p>

		# Selects the HIF address bits used as row address bit 9. Valid Range: 0 t
    # o 11 Internal Base: 15 The selected HIF address bit for each of the row
    # address bits is determined by adding the internal base to the value of t
    # his field. This register field is used only when ADDRMAP5.addrmap_row_b2
    # _10 is set to value 15.
		# PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B9                                               0x8

		# Selects the HIF address bits used as row address bit 8. Valid Range: 0 t
    # o 11 Internal Base: 14 The selected HIF address bit for each of the row
    # address bits is determined by adding the internal base to the value of t
    # his field. This register field is used only when ADDRMAP5.addrmap_row_b2
    # _10 is set to value 15.
		# PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B8                                               0x8

		# Selects the HIF address bits used as row address bit 7. Valid Range: 0 t
    # o 11 Internal Base: 13 The selected HIF address bit for each of the row
    # address bits is determined by adding the internal base to the value of t
    # his field. This register field is used only when ADDRMAP5.addrmap_row_b2
    # _10 is set to value 15.
		# PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B7                                               0x8

		# Selects the HIF address bits used as row address bit 6. Valid Range: 0 t
    # o 11 Internal Base: 12 The selected HIF address bit for each of the row
    # address bits is determined by adding the internal base to the value of t
    # his field. This register field is used only when ADDRMAP5.addrmap_row_b2
    # _10 is set to value 15.
		# PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B6                                               0x8

		# Address Map Register 10
		#(OFFSET, MASK, VALUE)      (0XFD070228, 0x0F0F0F0FU ,0x08080808U)  */
    mask_write 0XFD070228 0x0F0F0F0F 0x08080808
		# Register : ADDRMAP11 @ 0XFD07022C</p>

		# Selects the HIF address bits used as row address bit 10. Valid Range: 0
    # to 11 Internal Base: 16 The selected HIF address bit for each of the row
    #  address bits is determined by adding the internal base to the value of
    # this field. This register field is used only when ADDRMAP5.addrmap_row_b
    # 2_10 is set to value 15.
		# PSU_DDRC_ADDRMAP11_ADDRMAP_ROW_B10                                              0x8

		# Address Map Register 11
		#(OFFSET, MASK, VALUE)      (0XFD07022C, 0x0000000FU ,0x00000008U)  */
    mask_write 0XFD07022C 0x0000000F 0x00000008
		# Register : ODTCFG @ 0XFD070240</p>

		# Cycles to hold ODT for a write command. The minimum supported value is 2
    # . Recommended values: DDR2: - BL8: 0x5 (DDR2-400/533/667), 0x6 (DDR2-800
    # ), 0x7 (DDR2-1066) - BL4: 0x3 (DDR2-400/533/667), 0x4 (DDR2-800), 0x5 (D
    # DR2-1066) DDR3: - BL8: 0x6 DDR4: - BL8: 5 + WR_PREAMBLE + CRC_MODE WR_PR
    # EAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) CRC_MODE = 0 (
    # not CRC mode), 1 (CRC mode) LPDDR3: - BL8: 7 + RU(tODTon(max)/tCK)
		# PSU_DDRC_ODTCFG_WR_ODT_HOLD                                                     0x6

		# The delay, in clock cycles, from issuing a write command to setting ODT
    # values associated with that command. ODT setting must remain constant fo
    # r the entire time that DQS is driven by the uMCTL2. Recommended values:
    # DDR2: - CWL + AL - 3 (DDR2-400/533/667), CWL + AL - 4 (DDR2-800), CWL +
    # AL - 5 (DDR2-1066) If (CWL + AL - 3 < 0), uMCTL2 does not support ODT fo
    # r write operation. DDR3: - 0x0 DDR4: - DFITMG1.dfi_t_cmd_lat (to adjust
    # for CAL mode) LPDDR3: - WL - 1 - RU(tODTon(max)/tCK))
		# PSU_DDRC_ODTCFG_WR_ODT_DELAY                                                    0x0

		# Cycles to hold ODT for a read command. The minimum supported value is 2.
    #  Recommended values: DDR2: - BL8: 0x6 (not DDR2-1066), 0x7 (DDR2-1066) -
    #  BL4: 0x4 (not DDR2-1066), 0x5 (DDR2-1066) DDR3: - BL8 - 0x6 DDR4: - BL8
    # : 5 + RD_PREAMBLE RD_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write p
    # reamble) LPDDR3: - BL8: 5 + RU(tDQSCK(max)/tCK) - RD(tDQSCK(min)/tCK) +
    # RU(tODTon(max)/tCK)
		# PSU_DDRC_ODTCFG_RD_ODT_HOLD                                                     0x6

		# The delay, in clock cycles, from issuing a read command to setting ODT v
    # alues associated with that command. ODT setting must remain constant for
    #  the entire time that DQS is driven by the uMCTL2. Recommended values: D
    # DR2: - CL + AL - 4 (not DDR2-1066), CL + AL - 5 (DDR2-1066) If (CL + AL
    # - 4 < 0), uMCTL2 does not support ODT for read operation. DDR3: - CL - C
    # WL DDR4: - CL - CWL - RD_PREAMBLE + WR_PREAMBLE + DFITMG1.dfi_t_cmd_lat
    # (to adjust for CAL mode) WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK
    # write preamble) RD_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write pre
    # amble) If (CL - CWL - RD_PREAMBLE + WR_PREAMBLE) < 0, uMCTL2 does not su
    # pport ODT for read operation. LPDDR3: - RL + RD(tDQSCK(min)/tCK) - 1 - R
    # U(tODTon(max)/tCK)
		# PSU_DDRC_ODTCFG_RD_ODT_DELAY                                                    0x0

		# ODT Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD070240, 0x0F1F0F7CU ,0x06000600U)  */
    mask_write 0XFD070240 0x0F1F0F7C 0x06000600
		# Register : ODTMAP @ 0XFD070244</p>

		# Indicates which remote ODTs must be turned on during a read from rank 1.
    #  Each rank has a remote ODT (in the SDRAM) which can be turned on by set
    # ting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 i
    # s controlled by bit next to the LSB, etc. For each rank, set its bit to
    # 1 to enable its ODT. Present only in configurations that have 2 or more
    # ranks
		# PSU_DDRC_ODTMAP_RANK1_RD_ODT                                                    0x0

		# Indicates which remote ODTs must be turned on during a write to rank 1.
    # Each rank has a remote ODT (in the SDRAM) which can be turned on by sett
    # ing the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is
    #  controlled by bit next to the LSB, etc. For each rank, set its bit to 1
    #  to enable its ODT. Present only in configurations that have 2 or more r
    # anks
		# PSU_DDRC_ODTMAP_RANK1_WR_ODT                                                    0x0

		# Indicates which remote ODTs must be turned on during a read from rank 0.
    #  Each rank has a remote ODT (in the SDRAM) which can be turned on by set
    # ting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 i
    # s controlled by bit next to the LSB, etc. For each rank, set its bit to
    # 1 to enable its ODT.
		# PSU_DDRC_ODTMAP_RANK0_RD_ODT                                                    0x0

		# Indicates which remote ODTs must be turned on during a write to rank 0.
    # Each rank has a remote ODT (in the SDRAM) which can be turned on by sett
    # ing the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is
    #  controlled by bit next to the LSB, etc. For each rank, set its bit to 1
    #  to enable its ODT.
		# PSU_DDRC_ODTMAP_RANK0_WR_ODT                                                    0x1

		# ODT/Rank Map Register
		#(OFFSET, MASK, VALUE)      (0XFD070244, 0x00003333U ,0x00000001U)  */
    mask_write 0XFD070244 0x00003333 0x00000001
		# Register : SCHED @ 0XFD070250</p>

		# When the preferred transaction store is empty for these many clock cycle
    # s, switch to the alternate transaction store if it is non-empty. The rea
    # d transaction store (both high and low priority) is the default preferre
    # d transaction store and the write transaction store is the alternative s
    # tore. When prefer write over read is set this is reversed. 0x0 is a lega
    # l value for this register. When set to 0x0, the transaction store switch
    # ing will happen immediately when the switching conditions become true. F
    # OR PERFORMANCE ONLY
		# PSU_DDRC_SCHED_RDWR_IDLE_GAP                                                    0x1

		# UNUSED
		# PSU_DDRC_SCHED_GO2CRITICAL_HYSTERESIS                                           0x0

		# Number of entries in the low priority transaction store is this value +
    # 1. (MEMC_NO_OF_ENTRY - (SCHED.lpr_num_entries + 1)) is the number of ent
    # ries available for the high priority transaction store. Setting this to
    # maximum value allocates all entries to low priority transaction store. S
    # etting this to 0 allocates 1 entry to low priority transaction store and
    #  the rest to high priority transaction store. Note: In ECC configuration
    # s, the numbers of write and low priority read credits issued is one less
    #  than in the non-ECC case. One entry each is reserved in the write and l
    # ow-priority read CAMs for storing the RMW requests arising out of single
    #  bit error correction RMW operation.
		# PSU_DDRC_SCHED_LPR_NUM_ENTRIES                                                  0x20

		# If true, bank is kept open only while there are page hit transactions av
    # ailable in the CAM to that bank. The last read or write command in the C
    # AM with a bank and page hit will be executed with auto-precharge if SCHE
    # D1.pageclose_timer=0. Even if this register set to 1 and SCHED1.pageclos
    # e_timer is set to 0, explicit precharge (and not auto-precharge) may be
    # issued in some cases where there is a mode switch between Write and Read
    #  or between LPR and HPR. The Read and Write commands that are executed a
    # s part of the ECC scrub requests are also executed without auto-precharg
    # e. If false, the bank remains open until there is a need to close it (to
    #  open a different page, or for page timeout or refresh timeout) - also k
    # nown as open page policy. The open page policy can be overridden by sett
    # ing the per-command-autopre bit on the HIF interface (hif_cmd_autopre).
    # The pageclose feature provids a midway between Open and Close page polic
    # ies. FOR PERFORMANCE ONLY.
		# PSU_DDRC_SCHED_PAGECLOSE                                                        0x0

		# If set then the bank selector prefers writes over reads. FOR DEBUG ONLY.
		# PSU_DDRC_SCHED_PREFER_WRITE                                                     0x0

		# Active low signal. When asserted ('0'), all incoming transactions are fo
    # rced to low priority. This implies that all High Priority Read (HPR) and
    #  Variable Priority Read commands (VPR) will be treated as Low Priority R
    # ead (LPR) commands. On the write side, all Variable Priority Write (VPW)
    #  commands will be treated as Normal Priority Write (NPW) commands. Forci
    # ng the incoming transactions to low priority implicitly turns off Bypass
    #  path for read commands. FOR PERFORMANCE ONLY.
		# PSU_DDRC_SCHED_FORCE_LOW_PRI_N                                                  0x1

		# Scheduler Control Register
		#(OFFSET, MASK, VALUE)      (0XFD070250, 0x7FFF3F07U ,0x01002001U)  */
    mask_write 0XFD070250 0x7FFF3F07 0x01002001
		# Register : PERFLPR1 @ 0XFD070264</p>

		# Number of transactions that are serviced once the LPR queue goes critica
    # l is the smaller of: - (a) This number - (b) Number of transactions avai
    # lable. Unit: Transaction. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH                                           0x8

		# Number of clocks that the LPR queue can be starved before it goes critic
    # al. The minimum valid functional value for this register is 0x1. Program
    # ming it to 0x0 will disable the starvation functionality; during normal
    # operation, this function should not be disabled as it will cause excessi
    # ve latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PERFLPR1_LPR_MAX_STARVE                                                0x40

		# Low Priority Read CAM Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070264, 0xFF00FFFFU ,0x08000040U)  */
    mask_write 0XFD070264 0xFF00FFFF 0x08000040
		# Register : PERFWR1 @ 0XFD07026C</p>

		# Number of transactions that are serviced once the WR queue goes critical
    #  is the smaller of: - (a) This number - (b) Number of transactions avail
    # able. Unit: Transaction. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PERFWR1_W_XACT_RUN_LENGTH                                              0x8

		# Number of clocks that the WR queue can be starved before it goes critica
    # l. The minimum valid functional value for this register is 0x1. Programm
    # ing it to 0x0 will disable the starvation functionality; during normal o
    # peration, this function should not be disabled as it will cause excessiv
    # e latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY.
		# PSU_DDRC_PERFWR1_W_MAX_STARVE                                                   0x40

		# Write CAM Register 1
		#(OFFSET, MASK, VALUE)      (0XFD07026C, 0xFF00FFFFU ,0x08000040U)  */
    mask_write 0XFD07026C 0xFF00FFFF 0x08000040
		# Register : DQMAP0 @ 0XFD070280</p>

		# DQ nibble map for DQ bits [12-15] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP0_DQ_NIBBLE_MAP_12_15                                             0x0

		# DQ nibble map for DQ bits [8-11] Present only in designs configured to s
    # upport DDR4.
		# PSU_DDRC_DQMAP0_DQ_NIBBLE_MAP_8_11                                              0x0

		# DQ nibble map for DQ bits [4-7] Present only in designs configured to su
    # pport DDR4.
		# PSU_DDRC_DQMAP0_DQ_NIBBLE_MAP_4_7                                               0x0

		# DQ nibble map for DQ bits [0-3] Present only in designs configured to su
    # pport DDR4.
		# PSU_DDRC_DQMAP0_DQ_NIBBLE_MAP_0_3                                               0x0

		# DQ Map Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070280, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD070280 0xFFFFFFFF 0x00000000
		# Register : DQMAP1 @ 0XFD070284</p>

		# DQ nibble map for DQ bits [28-31] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP1_DQ_NIBBLE_MAP_28_31                                             0x0

		# DQ nibble map for DQ bits [24-27] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP1_DQ_NIBBLE_MAP_24_27                                             0x0

		# DQ nibble map for DQ bits [20-23] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP1_DQ_NIBBLE_MAP_20_23                                             0x0

		# DQ nibble map for DQ bits [16-19] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP1_DQ_NIBBLE_MAP_16_19                                             0x0

		# DQ Map Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070284, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD070284 0xFFFFFFFF 0x00000000
		# Register : DQMAP2 @ 0XFD070288</p>

		# DQ nibble map for DQ bits [44-47] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP2_DQ_NIBBLE_MAP_44_47                                             0x0

		# DQ nibble map for DQ bits [40-43] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP2_DQ_NIBBLE_MAP_40_43                                             0x0

		# DQ nibble map for DQ bits [36-39] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP2_DQ_NIBBLE_MAP_36_39                                             0x0

		# DQ nibble map for DQ bits [32-35] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP2_DQ_NIBBLE_MAP_32_35                                             0x0

		# DQ Map Register 2
		#(OFFSET, MASK, VALUE)      (0XFD070288, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD070288 0xFFFFFFFF 0x00000000
		# Register : DQMAP3 @ 0XFD07028C</p>

		# DQ nibble map for DQ bits [60-63] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP3_DQ_NIBBLE_MAP_60_63                                             0x0

		# DQ nibble map for DQ bits [56-59] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP3_DQ_NIBBLE_MAP_56_59                                             0x0

		# DQ nibble map for DQ bits [52-55] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP3_DQ_NIBBLE_MAP_52_55                                             0x0

		# DQ nibble map for DQ bits [48-51] Present only in designs configured to
    # support DDR4.
		# PSU_DDRC_DQMAP3_DQ_NIBBLE_MAP_48_51                                             0x0

		# DQ Map Register 3
		#(OFFSET, MASK, VALUE)      (0XFD07028C, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD07028C 0xFFFFFFFF 0x00000000
		# Register : DQMAP4 @ 0XFD070290</p>

		# DQ nibble map for DIMM ECC check bits [4-7] Present only in designs conf
    # igured to support DDR4.
		# PSU_DDRC_DQMAP4_DQ_NIBBLE_MAP_CB_4_7                                            0x0

		# DQ nibble map for DIMM ECC check bits [0-3] Present only in designs conf
    # igured to support DDR4.
		# PSU_DDRC_DQMAP4_DQ_NIBBLE_MAP_CB_0_3                                            0x0

		# DQ Map Register 4
		#(OFFSET, MASK, VALUE)      (0XFD070290, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD070290 0x0000FFFF 0x00000000
		# Register : DQMAP5 @ 0XFD070294</p>

		# All even ranks have the same DQ mapping controled by DQMAP0-4 register a
    # s rank 0. This register provides DQ swap function for all odd ranks to s
    # upport CRC feature. rank based DQ swapping is: swap bit 0 with 1, swap b
    # it 2 with 3, swap bit 4 with 5 and swap bit 6 with 7. 1: Disable rank ba
    # sed DQ swapping 0: Enable rank based DQ swapping Present only in designs
    #  configured to support DDR4.
		# PSU_DDRC_DQMAP5_DIS_DQ_RANK_SWAP                                                0x1

		# DQ Map Register 5
		#(OFFSET, MASK, VALUE)      (0XFD070294, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070294 0x00000001 0x00000001
		# Register : DBG0 @ 0XFD070300</p>

		# When this is set to '0', auto-precharge is disabled for the flushed comm
    # and in a collision case. Collision cases are write followed by read to s
    # ame address, read followed by write to same address, or write followed b
    # y write to same address with DBG0.dis_wc bit = 1 (where same address com
    # parisons exclude the two address bits representing critical word). FOR D
    # EBUG ONLY.
		# PSU_DDRC_DBG0_DIS_COLLISION_PAGE_OPT                                            0x0

		# When 1, disable write combine. FOR DEBUG ONLY
		# PSU_DDRC_DBG0_DIS_WC                                                            0x0

		# Debug Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070300, 0x00000011U ,0x00000000U)  */
    mask_write 0XFD070300 0x00000011 0x00000000
		# Register : DBGCMD @ 0XFD07030C</p>

		# Setting this register bit to 1 allows refresh and ZQCS commands to be tr
    # iggered from hardware via the IOs ext_*. If set to 1, the fields DBGCMD.
    # zq_calib_short and DBGCMD.rank*_refresh have no function, and are ignore
    # d by the uMCTL2 logic. Setting this register bit to 0 allows refresh and
    #  ZQCS to be triggered from software, via the fields DBGCMD.zq_calib_shor
    # t and DBGCMD.rank*_refresh. If set to 0, the hardware pins ext_* have no
    #  function, and are ignored by the uMCTL2 logic. This register is static,
    #  and may only be changed when the DDRC reset signal, core_ddrc_rstn, is
    # asserted (0).
		# PSU_DDRC_DBGCMD_HW_REF_ZQ_EN                                                    0x0

		# Setting this register bit to 1 indicates to the uMCTL2 to issue a dfi_ct
    # rlupd_req to the PHY. When this request is stored in the uMCTL2, the bit
    #  is automatically cleared. This operation must only be performed when DF
    # IUPD0.dis_auto_ctrlupd=1.
		# PSU_DDRC_DBGCMD_CTRLUPD                                                         0x0

		# Setting this register bit to 1 indicates to the uMCTL2 to issue a ZQCS (
    # ZQ calibration short)/MPC(ZQ calibration) command to the SDRAM. When thi
    # s request is stored in the uMCTL2, the bit is automatically cleared. Thi
    # s operation can be performed only when ZQCTL0.dis_auto_zq=1. It is recom
    # mended NOT to set this register bit if in Init operating mode. This regi
    # ster bit is ignored when in Self-Refresh(except LPDDR4) and SR-Powerdown
    # (LPDDR4) and Deep power-down operating modes and Maximum Power Saving Mo
    # de.
		# PSU_DDRC_DBGCMD_ZQ_CALIB_SHORT                                                  0x0

		# Setting this register bit to 1 indicates to the uMCTL2 to issue a refres
    # h to rank 1. Writing to this bit causes DBGSTAT.rank1_refresh_busy to be
    #  set. When DBGSTAT.rank1_refresh_busy is cleared, the command has been s
    # tored in uMCTL2. This operation can be performed only when RFSHCTL3.dis_
    # auto_refresh=1. It is recommended NOT to set this register bit if in Ini
    # t or Deep power-down operating modes or Maximum Power Saving Mode.
		# PSU_DDRC_DBGCMD_RANK1_REFRESH                                                   0x0

		# Setting this register bit to 1 indicates to the uMCTL2 to issue a refres
    # h to rank 0. Writing to this bit causes DBGSTAT.rank0_refresh_busy to be
    #  set. When DBGSTAT.rank0_refresh_busy is cleared, the command has been s
    # tored in uMCTL2. This operation can be performed only when RFSHCTL3.dis_
    # auto_refresh=1. It is recommended NOT to set this register bit if in Ini
    # t or Deep power-down operating modes or Maximum Power Saving Mode.
		# PSU_DDRC_DBGCMD_RANK0_REFRESH                                                   0x0

		# Command Debug Register
		#(OFFSET, MASK, VALUE)      (0XFD07030C, 0x80000033U ,0x00000000U)  */
    mask_write 0XFD07030C 0x80000033 0x00000000
		# Register : SWCTL @ 0XFD070320</p>

		# Enable quasi-dynamic register programming outside reset. Program registe
    # r to 0 to enable quasi-dynamic programming. Set back register to 1 once
    # programming is done.
		# PSU_DDRC_SWCTL_SW_DONE                                                          0x0

		# Software register programming control enable
		#(OFFSET, MASK, VALUE)      (0XFD070320, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD070320 0x00000001 0x00000000
		# Register : PCCFG @ 0XFD070400</p>

		# Burst length expansion mode. By default (i.e. bl_exp_mode==0) XPI expand
    # s every AXI burst into multiple HIF commands, using the memory burst len
    # gth as a unit. If set to 1, then XPI will use half of the memory burst l
    # ength as a unit. This applies to both reads and writes. When MSTR.data_b
    # us_width==00, setting bl_exp_mode to 1 has no effect. This can be used i
    # n cases where Partial Writes is enabled (UMCTL2_PARTIAL_WR=1) and DBG0.d
    # is_wc=1, in order to avoid or minimize t_ccd_l penalty in DDR4 and t_ccd
    # _mw penalty in LPDDR4. Note that if DBICTL.reg_ddrc_dm_en=0, functionali
    # ty is not supported in the following cases: - UMCTL2_PARTIAL_WR=0 - UMCT
    # L2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=8 an
    # d MSTR.reg_ddrc_burst_rdwr=1000 (LPDDR4 only) - UMCTL2_PARTIAL_WR=1, MST
    # R.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=4 and MSTR.reg_ddrc_burs
    # t_rdwr=0100 (DDR4 only), with either MSTR.reg_ddrc_burstchop=0 or CRCPAR
    # CTL1.reg_ddrc_crc_enable=1 Functionality is also not supported if Shared
    # -AC is enabled
		# PSU_DDRC_PCCFG_BL_EXP_MODE                                                      0x0

		# Page match four limit. If set to 1, limits the number of consecutive sam
    # e page DDRC transactions that can be granted by the Port Arbiter to four
    #  when Page Match feature is enabled. If set to 0, there is no limit impo
    # sed on number of consecutive same page DDRC transactions.
		# PSU_DDRC_PCCFG_PAGEMATCH_LIMIT                                                  0x0

		# If set to 1 (enabled), sets co_gs_go2critical_wr and co_gs_go2critical_l
    # pr/co_gs_go2critical_hpr signals going to DDRC based on urgent input (aw
    # urgent, arurgent) coming from AXI master. If set to 0 (disabled), co_gs_
    # go2critical_wr and co_gs_go2critical_lpr/co_gs_go2critical_hpr signals a
    # t DDRC are driven to 1b'0.
		# PSU_DDRC_PCCFG_GO2CRITICAL_EN                                                   0x1

		# Port Common Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD070400, 0x00000111U ,0x00000001U)  */
    mask_write 0XFD070400 0x00000111 0x00000001
		# Register : PCFGR_0 @ 0XFD070404</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (arurgent). When ena
    # bled and arurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DD
    # RC is asserted if enabled in PCCFG.go2critical_en register. Note that ar
    # urgent signal can be asserted anytime and as long as required which is i
    # ndependent of address handshaking (it is not associated with any particu
    # lar command).
		# PSU_DDRC_PCFGR_0_RD_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the read channel of the port.
		# PSU_DDRC_PCFGR_0_RD_PORT_AGING_EN                                               0x0

		# Determines the initial load value of read aging counters. These counters
    #  will be parallel loaded after reset, or after each grant to the corresp
    # onding port. The aging counters down-count every clock cycle where the p
    # ort is requesting but not granted. The higher significant 5-bits of the
    # read aging counter sets the priority of the read channel of a given port
    # . Port's priority will increase as the higher significant 5-bits of the
    # counter starts to decrease. When the aging counter becomes 0, the corres
    # ponding port channel will have the highest priority level (timeout condi
    # tion - Priority0). For multi-port configurations, the aging counters can
    # not be used to set port priorities when external dynamic priority inputs
    #  (arqos) are enabled (timeout is still applicable). For single port conf
    # igurations, the aging counters are only used when they timeout (become 0
    # ) to force read-write direction switching. In this case, external dynami
    # c priority input, arqos (for reads only) can still be used to set the DD
    # RC read priority (2 priority levels: low priority read - LPR, high prior
    # ity read - HPR) on a command by command basis. Note: The two LSBs of thi
    # s register field are tied internally to 2'b00.
		# PSU_DDRC_PCFGR_0_RD_PORT_PRIORITY                                               0xf

		# Port n Configuration Read Register
		#(OFFSET, MASK, VALUE)      (0XFD070404, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070404 0x000073FF 0x0000200F
		# Register : PCFGW_0 @ 0XFD070408</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (awurgent). When ena
    # bled and awurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_wr signal to DDRC is asserted if enabl
    # ed in PCCFG.go2critical_en register. Note that awurgent signal can be as
    # serted anytime and as long as required which is independent of address h
    # andshaking (it is not associated with any particular command).
		# PSU_DDRC_PCFGW_0_WR_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the write channel of the port.
		# PSU_DDRC_PCFGW_0_WR_PORT_AGING_EN                                               0x0

		# Determines the initial load value of write aging counters. These counter
    # s will be parallel loaded after reset, or after each grant to the corres
    # ponding port. The aging counters down-count every clock cycle where the
    # port is requesting but not granted. The higher significant 5-bits of the
    #  write aging counter sets the initial priority of the write channel of a
    #  given port. Port's priority will increase as the higher significant 5-b
    # its of the counter starts to decrease. When the aging counter becomes 0,
    #  the corresponding port channel will have the highest priority level. Fo
    # r multi-port configurations, the aging counters cannot be used to set po
    # rt priorities when external dynamic priority inputs (awqos) are enabled
    # (timeout is still applicable). For single port configurations, the aging
    #  counters are only used when they timeout (become 0) to force read-write
    #  direction switching. Note: The two LSBs of this register field are tied
    #  internally to 2'b00.
		# PSU_DDRC_PCFGW_0_WR_PORT_PRIORITY                                               0xf

		# Port n Configuration Write Register
		#(OFFSET, MASK, VALUE)      (0XFD070408, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070408 0x000073FF 0x0000200F
		# Register : PCTRL_0 @ 0XFD070490</p>

		# Enables port n.
		# PSU_DDRC_PCTRL_0_PORT_EN                                                        0x1

		# Port n Control Register
		#(OFFSET, MASK, VALUE)      (0XFD070490, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070490 0x00000001 0x00000001
		# Register : PCFGQOS0_0 @ 0XFD070494</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0 : LPR, 1: VPR, 2: HPR. For dual address queue configurations, region1
    #  maps to the blue address queue. In this case, valid values are 0: LPR a
    # nd 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tra
    # ffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_0_RQOS_MAP_REGION1                                            0x2

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: LPR, 1: VPR, 2: HPR. For dual address queue configurations, region 0
    #  maps to the blue address queue. In this case, valid values are: 0: LPR
    # and 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tr
    # affic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_0_RQOS_MAP_REGION0                                            0x0

		# Separation level1 indicating the end of region0 mapping; start of region
    # 0 is 0. Possible values for level1 are 0 to 13 (for dual RAQ) or 0 to 14
    #  (for single RAQ) which corresponds to arqos. Note that for PA, arqos va
    # lues are used directly as port priorities, where the higher the value co
    # rresponds to higher port priority. All of the map_level* registers must
    # be set to distinct values.
		# PSU_DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1                                             0xb

		# Port n Read QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070494, 0x0033000FU ,0x0020000BU)  */
    mask_write 0XFD070494 0x0033000F 0x0020000B
		# Register : PCFGQOS1_0 @ 0XFD070498</p>

		# Specifies the timeout value for transactions mapped to the red address q
    # ueue.
		# PSU_DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR                                           0x0

		# Specifies the timeout value for transactions mapped to the blue address
    # queue.
		# PSU_DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB                                           0x0

		# Port n Read QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070498, 0x07FF07FFU ,0x00000000U)  */
    mask_write 0XFD070498 0x07FF07FF 0x00000000
		# Register : PCFGR_1 @ 0XFD0704B4</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (arurgent). When ena
    # bled and arurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DD
    # RC is asserted if enabled in PCCFG.go2critical_en register. Note that ar
    # urgent signal can be asserted anytime and as long as required which is i
    # ndependent of address handshaking (it is not associated with any particu
    # lar command).
		# PSU_DDRC_PCFGR_1_RD_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the read channel of the port.
		# PSU_DDRC_PCFGR_1_RD_PORT_AGING_EN                                               0x0

		# Determines the initial load value of read aging counters. These counters
    #  will be parallel loaded after reset, or after each grant to the corresp
    # onding port. The aging counters down-count every clock cycle where the p
    # ort is requesting but not granted. The higher significant 5-bits of the
    # read aging counter sets the priority of the read channel of a given port
    # . Port's priority will increase as the higher significant 5-bits of the
    # counter starts to decrease. When the aging counter becomes 0, the corres
    # ponding port channel will have the highest priority level (timeout condi
    # tion - Priority0). For multi-port configurations, the aging counters can
    # not be used to set port priorities when external dynamic priority inputs
    #  (arqos) are enabled (timeout is still applicable). For single port conf
    # igurations, the aging counters are only used when they timeout (become 0
    # ) to force read-write direction switching. In this case, external dynami
    # c priority input, arqos (for reads only) can still be used to set the DD
    # RC read priority (2 priority levels: low priority read - LPR, high prior
    # ity read - HPR) on a command by command basis. Note: The two LSBs of thi
    # s register field are tied internally to 2'b00.
		# PSU_DDRC_PCFGR_1_RD_PORT_PRIORITY                                               0xf

		# Port n Configuration Read Register
		#(OFFSET, MASK, VALUE)      (0XFD0704B4, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD0704B4 0x000073FF 0x0000200F
		# Register : PCFGW_1 @ 0XFD0704B8</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (awurgent). When ena
    # bled and awurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_wr signal to DDRC is asserted if enabl
    # ed in PCCFG.go2critical_en register. Note that awurgent signal can be as
    # serted anytime and as long as required which is independent of address h
    # andshaking (it is not associated with any particular command).
		# PSU_DDRC_PCFGW_1_WR_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the write channel of the port.
		# PSU_DDRC_PCFGW_1_WR_PORT_AGING_EN                                               0x0

		# Determines the initial load value of write aging counters. These counter
    # s will be parallel loaded after reset, or after each grant to the corres
    # ponding port. The aging counters down-count every clock cycle where the
    # port is requesting but not granted. The higher significant 5-bits of the
    #  write aging counter sets the initial priority of the write channel of a
    #  given port. Port's priority will increase as the higher significant 5-b
    # its of the counter starts to decrease. When the aging counter becomes 0,
    #  the corresponding port channel will have the highest priority level. Fo
    # r multi-port configurations, the aging counters cannot be used to set po
    # rt priorities when external dynamic priority inputs (awqos) are enabled
    # (timeout is still applicable). For single port configurations, the aging
    #  counters are only used when they timeout (become 0) to force read-write
    #  direction switching. Note: The two LSBs of this register field are tied
    #  internally to 2'b00.
		# PSU_DDRC_PCFGW_1_WR_PORT_PRIORITY                                               0xf

		# Port n Configuration Write Register
		#(OFFSET, MASK, VALUE)      (0XFD0704B8, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD0704B8 0x000073FF 0x0000200F
		# Register : PCTRL_1 @ 0XFD070540</p>

		# Enables port n.
		# PSU_DDRC_PCTRL_1_PORT_EN                                                        0x1

		# Port n Control Register
		#(OFFSET, MASK, VALUE)      (0XFD070540, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070540 0x00000001 0x00000001
		# Register : PCFGQOS0_1 @ 0XFD070544</p>

		# This bitfield indicates the traffic class of region2. For dual address q
    # ueue configurations, region2 maps to the red address queue. Valid values
    #  are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN
    #  = 0) and traffic class of region2 is set to 1 (VPR), VPR traffic is ali
    # ased to LPR traffic.
		# PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION2                                            0x2

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0 : LPR, 1: VPR, 2: HPR. For dual address queue configurations, region1
    #  maps to the blue address queue. In this case, valid values are 0: LPR a
    # nd 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tra
    # ffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION1                                            0x0

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: LPR, 1: VPR, 2: HPR. For dual address queue configurations, region 0
    #  maps to the blue address queue. In this case, valid values are: 0: LPR
    # and 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tr
    # affic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION0                                            0x0

		# Separation level2 indicating the end of region1 mapping; start of region
    # 1 is (level1 + 1). Possible values for level2 are (level1 + 1) to 14 whi
    # ch corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note
    #  that for PA, arqos values are used directly as port priorities, where t
    # he higher the value corresponds to higher port priority. All of the map_
    # level* registers must be set to distinct values.
		# PSU_DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2                                             0xb

		# Separation level1 indicating the end of region0 mapping; start of region
    # 0 is 0. Possible values for level1 are 0 to 13 (for dual RAQ) or 0 to 14
    #  (for single RAQ) which corresponds to arqos. Note that for PA, arqos va
    # lues are used directly as port priorities, where the higher the value co
    # rresponds to higher port priority. All of the map_level* registers must
    # be set to distinct values.
		# PSU_DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1                                             0x3

		# Port n Read QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070544, 0x03330F0FU ,0x02000B03U)  */
    mask_write 0XFD070544 0x03330F0F 0x02000B03
		# Register : PCFGQOS1_1 @ 0XFD070548</p>

		# Specifies the timeout value for transactions mapped to the red address q
    # ueue.
		# PSU_DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR                                           0x0

		# Specifies the timeout value for transactions mapped to the blue address
    # queue.
		# PSU_DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB                                           0x0

		# Port n Read QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070548, 0x07FF07FFU ,0x00000000U)  */
    mask_write 0XFD070548 0x07FF07FF 0x00000000
		# Register : PCFGR_2 @ 0XFD070564</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (arurgent). When ena
    # bled and arurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DD
    # RC is asserted if enabled in PCCFG.go2critical_en register. Note that ar
    # urgent signal can be asserted anytime and as long as required which is i
    # ndependent of address handshaking (it is not associated with any particu
    # lar command).
		# PSU_DDRC_PCFGR_2_RD_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the read channel of the port.
		# PSU_DDRC_PCFGR_2_RD_PORT_AGING_EN                                               0x0

		# Determines the initial load value of read aging counters. These counters
    #  will be parallel loaded after reset, or after each grant to the corresp
    # onding port. The aging counters down-count every clock cycle where the p
    # ort is requesting but not granted. The higher significant 5-bits of the
    # read aging counter sets the priority of the read channel of a given port
    # . Port's priority will increase as the higher significant 5-bits of the
    # counter starts to decrease. When the aging counter becomes 0, the corres
    # ponding port channel will have the highest priority level (timeout condi
    # tion - Priority0). For multi-port configurations, the aging counters can
    # not be used to set port priorities when external dynamic priority inputs
    #  (arqos) are enabled (timeout is still applicable). For single port conf
    # igurations, the aging counters are only used when they timeout (become 0
    # ) to force read-write direction switching. In this case, external dynami
    # c priority input, arqos (for reads only) can still be used to set the DD
    # RC read priority (2 priority levels: low priority read - LPR, high prior
    # ity read - HPR) on a command by command basis. Note: The two LSBs of thi
    # s register field are tied internally to 2'b00.
		# PSU_DDRC_PCFGR_2_RD_PORT_PRIORITY                                               0xf

		# Port n Configuration Read Register
		#(OFFSET, MASK, VALUE)      (0XFD070564, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070564 0x000073FF 0x0000200F
		# Register : PCFGW_2 @ 0XFD070568</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (awurgent). When ena
    # bled and awurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_wr signal to DDRC is asserted if enabl
    # ed in PCCFG.go2critical_en register. Note that awurgent signal can be as
    # serted anytime and as long as required which is independent of address h
    # andshaking (it is not associated with any particular command).
		# PSU_DDRC_PCFGW_2_WR_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the write channel of the port.
		# PSU_DDRC_PCFGW_2_WR_PORT_AGING_EN                                               0x0

		# Determines the initial load value of write aging counters. These counter
    # s will be parallel loaded after reset, or after each grant to the corres
    # ponding port. The aging counters down-count every clock cycle where the
    # port is requesting but not granted. The higher significant 5-bits of the
    #  write aging counter sets the initial priority of the write channel of a
    #  given port. Port's priority will increase as the higher significant 5-b
    # its of the counter starts to decrease. When the aging counter becomes 0,
    #  the corresponding port channel will have the highest priority level. Fo
    # r multi-port configurations, the aging counters cannot be used to set po
    # rt priorities when external dynamic priority inputs (awqos) are enabled
    # (timeout is still applicable). For single port configurations, the aging
    #  counters are only used when they timeout (become 0) to force read-write
    #  direction switching. Note: The two LSBs of this register field are tied
    #  internally to 2'b00.
		# PSU_DDRC_PCFGW_2_WR_PORT_PRIORITY                                               0xf

		# Port n Configuration Write Register
		#(OFFSET, MASK, VALUE)      (0XFD070568, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070568 0x000073FF 0x0000200F
		# Register : PCTRL_2 @ 0XFD0705F0</p>

		# Enables port n.
		# PSU_DDRC_PCTRL_2_PORT_EN                                                        0x1

		# Port n Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0705F0, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD0705F0 0x00000001 0x00000001
		# Register : PCFGQOS0_2 @ 0XFD0705F4</p>

		# This bitfield indicates the traffic class of region2. For dual address q
    # ueue configurations, region2 maps to the red address queue. Valid values
    #  are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN
    #  = 0) and traffic class of region2 is set to 1 (VPR), VPR traffic is ali
    # ased to LPR traffic.
		# PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION2                                            0x2

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0 : LPR, 1: VPR, 2: HPR. For dual address queue configurations, region1
    #  maps to the blue address queue. In this case, valid values are 0: LPR a
    # nd 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tra
    # ffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION1                                            0x0

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: LPR, 1: VPR, 2: HPR. For dual address queue configurations, region 0
    #  maps to the blue address queue. In this case, valid values are: 0: LPR
    # and 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tr
    # affic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION0                                            0x0

		# Separation level2 indicating the end of region1 mapping; start of region
    # 1 is (level1 + 1). Possible values for level2 are (level1 + 1) to 14 whi
    # ch corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note
    #  that for PA, arqos values are used directly as port priorities, where t
    # he higher the value corresponds to higher port priority. All of the map_
    # level* registers must be set to distinct values.
		# PSU_DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2                                             0xb

		# Separation level1 indicating the end of region0 mapping; start of region
    # 0 is 0. Possible values for level1 are 0 to 13 (for dual RAQ) or 0 to 14
    #  (for single RAQ) which corresponds to arqos. Note that for PA, arqos va
    # lues are used directly as port priorities, where the higher the value co
    # rresponds to higher port priority. All of the map_level* registers must
    # be set to distinct values.
		# PSU_DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1                                             0x3

		# Port n Read QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0705F4, 0x03330F0FU ,0x02000B03U)  */
    mask_write 0XFD0705F4 0x03330F0F 0x02000B03
		# Register : PCFGQOS1_2 @ 0XFD0705F8</p>

		# Specifies the timeout value for transactions mapped to the red address q
    # ueue.
		# PSU_DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR                                           0x0

		# Specifies the timeout value for transactions mapped to the blue address
    # queue.
		# PSU_DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB                                           0x0

		# Port n Read QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD0705F8, 0x07FF07FFU ,0x00000000U)  */
    mask_write 0XFD0705F8 0x07FF07FF 0x00000000
		# Register : PCFGR_3 @ 0XFD070614</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (arurgent). When ena
    # bled and arurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DD
    # RC is asserted if enabled in PCCFG.go2critical_en register. Note that ar
    # urgent signal can be asserted anytime and as long as required which is i
    # ndependent of address handshaking (it is not associated with any particu
    # lar command).
		# PSU_DDRC_PCFGR_3_RD_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the read channel of the port.
		# PSU_DDRC_PCFGR_3_RD_PORT_AGING_EN                                               0x0

		# Determines the initial load value of read aging counters. These counters
    #  will be parallel loaded after reset, or after each grant to the corresp
    # onding port. The aging counters down-count every clock cycle where the p
    # ort is requesting but not granted. The higher significant 5-bits of the
    # read aging counter sets the priority of the read channel of a given port
    # . Port's priority will increase as the higher significant 5-bits of the
    # counter starts to decrease. When the aging counter becomes 0, the corres
    # ponding port channel will have the highest priority level (timeout condi
    # tion - Priority0). For multi-port configurations, the aging counters can
    # not be used to set port priorities when external dynamic priority inputs
    #  (arqos) are enabled (timeout is still applicable). For single port conf
    # igurations, the aging counters are only used when they timeout (become 0
    # ) to force read-write direction switching. In this case, external dynami
    # c priority input, arqos (for reads only) can still be used to set the DD
    # RC read priority (2 priority levels: low priority read - LPR, high prior
    # ity read - HPR) on a command by command basis. Note: The two LSBs of thi
    # s register field are tied internally to 2'b00.
		# PSU_DDRC_PCFGR_3_RD_PORT_PRIORITY                                               0xf

		# Port n Configuration Read Register
		#(OFFSET, MASK, VALUE)      (0XFD070614, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070614 0x000073FF 0x0000200F
		# Register : PCFGW_3 @ 0XFD070618</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (awurgent). When ena
    # bled and awurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_wr signal to DDRC is asserted if enabl
    # ed in PCCFG.go2critical_en register. Note that awurgent signal can be as
    # serted anytime and as long as required which is independent of address h
    # andshaking (it is not associated with any particular command).
		# PSU_DDRC_PCFGW_3_WR_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the write channel of the port.
		# PSU_DDRC_PCFGW_3_WR_PORT_AGING_EN                                               0x0

		# Determines the initial load value of write aging counters. These counter
    # s will be parallel loaded after reset, or after each grant to the corres
    # ponding port. The aging counters down-count every clock cycle where the
    # port is requesting but not granted. The higher significant 5-bits of the
    #  write aging counter sets the initial priority of the write channel of a
    #  given port. Port's priority will increase as the higher significant 5-b
    # its of the counter starts to decrease. When the aging counter becomes 0,
    #  the corresponding port channel will have the highest priority level. Fo
    # r multi-port configurations, the aging counters cannot be used to set po
    # rt priorities when external dynamic priority inputs (awqos) are enabled
    # (timeout is still applicable). For single port configurations, the aging
    #  counters are only used when they timeout (become 0) to force read-write
    #  direction switching. Note: The two LSBs of this register field are tied
    #  internally to 2'b00.
		# PSU_DDRC_PCFGW_3_WR_PORT_PRIORITY                                               0xf

		# Port n Configuration Write Register
		#(OFFSET, MASK, VALUE)      (0XFD070618, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070618 0x000073FF 0x0000200F
		# Register : PCTRL_3 @ 0XFD0706A0</p>

		# Enables port n.
		# PSU_DDRC_PCTRL_3_PORT_EN                                                        0x1

		# Port n Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0706A0, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD0706A0 0x00000001 0x00000001
		# Register : PCFGQOS0_3 @ 0XFD0706A4</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0 : LPR, 1: VPR, 2: HPR. For dual address queue configurations, region1
    #  maps to the blue address queue. In this case, valid values are 0: LPR a
    # nd 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tra
    # ffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_3_RQOS_MAP_REGION1                                            0x1

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: LPR, 1: VPR, 2: HPR. For dual address queue configurations, region 0
    #  maps to the blue address queue. In this case, valid values are: 0: LPR
    # and 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tr
    # affic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_3_RQOS_MAP_REGION0                                            0x0

		# Separation level1 indicating the end of region0 mapping; start of region
    # 0 is 0. Possible values for level1 are 0 to 13 (for dual RAQ) or 0 to 14
    #  (for single RAQ) which corresponds to arqos. Note that for PA, arqos va
    # lues are used directly as port priorities, where the higher the value co
    # rresponds to higher port priority. All of the map_level* registers must
    # be set to distinct values.
		# PSU_DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1                                             0x3

		# Port n Read QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0706A4, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD0706A4 0x0033000F 0x00100003
		# Register : PCFGQOS1_3 @ 0XFD0706A8</p>

		# Specifies the timeout value for transactions mapped to the red address q
    # ueue.
		# PSU_DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR                                           0x0

		# Specifies the timeout value for transactions mapped to the blue address
    # queue.
		# PSU_DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB                                           0x4f

		# Port n Read QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD0706A8, 0x07FF07FFU ,0x0000004FU)  */
    mask_write 0XFD0706A8 0x07FF07FF 0x0000004F
		# Register : PCFGWQOS0_3 @ 0XFD0706AC</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0: NPW, 1: VPW. When VPW support is disabled (UMCTL2_VPW_EN = 0) and tr
    # affic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW
    #  traffic.
		# PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1                                           0x1

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: NPW, 1: VPW. When VPW support is disabled (UMCTL2_VPW_EN = 0) and tr
    # affic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW
    # traffic.
		# PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0                                           0x0

		# Separation level indicating the end of region0 mapping; start of region0
    #  is 0. Possible values for level1 are 0 to 14 which corresponds to awqos
    # . Note that for PA, awqos values are used directly as port priorities, w
    # here the higher the value corresponds to higher port priority.
		# PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL                                             0x3

		# Port n Write QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0706AC, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD0706AC 0x0033000F 0x00100003
		# Register : PCFGWQOS1_3 @ 0XFD0706B0</p>

		# Specifies the timeout value for write transactions.
		# PSU_DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT                                           0x4f

		# Port n Write QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD0706B0, 0x000007FFU ,0x0000004FU)  */
    mask_write 0XFD0706B0 0x000007FF 0x0000004F
		# Register : PCFGR_4 @ 0XFD0706C4</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (arurgent). When ena
    # bled and arurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DD
    # RC is asserted if enabled in PCCFG.go2critical_en register. Note that ar
    # urgent signal can be asserted anytime and as long as required which is i
    # ndependent of address handshaking (it is not associated with any particu
    # lar command).
		# PSU_DDRC_PCFGR_4_RD_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the read channel of the port.
		# PSU_DDRC_PCFGR_4_RD_PORT_AGING_EN                                               0x0

		# Determines the initial load value of read aging counters. These counters
    #  will be parallel loaded after reset, or after each grant to the corresp
    # onding port. The aging counters down-count every clock cycle where the p
    # ort is requesting but not granted. The higher significant 5-bits of the
    # read aging counter sets the priority of the read channel of a given port
    # . Port's priority will increase as the higher significant 5-bits of the
    # counter starts to decrease. When the aging counter becomes 0, the corres
    # ponding port channel will have the highest priority level (timeout condi
    # tion - Priority0). For multi-port configurations, the aging counters can
    # not be used to set port priorities when external dynamic priority inputs
    #  (arqos) are enabled (timeout is still applicable). For single port conf
    # igurations, the aging counters are only used when they timeout (become 0
    # ) to force read-write direction switching. In this case, external dynami
    # c priority input, arqos (for reads only) can still be used to set the DD
    # RC read priority (2 priority levels: low priority read - LPR, high prior
    # ity read - HPR) on a command by command basis. Note: The two LSBs of thi
    # s register field are tied internally to 2'b00.
		# PSU_DDRC_PCFGR_4_RD_PORT_PRIORITY                                               0xf

		# Port n Configuration Read Register
		#(OFFSET, MASK, VALUE)      (0XFD0706C4, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD0706C4 0x000073FF 0x0000200F
		# Register : PCFGW_4 @ 0XFD0706C8</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (awurgent). When ena
    # bled and awurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_wr signal to DDRC is asserted if enabl
    # ed in PCCFG.go2critical_en register. Note that awurgent signal can be as
    # serted anytime and as long as required which is independent of address h
    # andshaking (it is not associated with any particular command).
		# PSU_DDRC_PCFGW_4_WR_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the write channel of the port.
		# PSU_DDRC_PCFGW_4_WR_PORT_AGING_EN                                               0x0

		# Determines the initial load value of write aging counters. These counter
    # s will be parallel loaded after reset, or after each grant to the corres
    # ponding port. The aging counters down-count every clock cycle where the
    # port is requesting but not granted. The higher significant 5-bits of the
    #  write aging counter sets the initial priority of the write channel of a
    #  given port. Port's priority will increase as the higher significant 5-b
    # its of the counter starts to decrease. When the aging counter becomes 0,
    #  the corresponding port channel will have the highest priority level. Fo
    # r multi-port configurations, the aging counters cannot be used to set po
    # rt priorities when external dynamic priority inputs (awqos) are enabled
    # (timeout is still applicable). For single port configurations, the aging
    #  counters are only used when they timeout (become 0) to force read-write
    #  direction switching. Note: The two LSBs of this register field are tied
    #  internally to 2'b00.
		# PSU_DDRC_PCFGW_4_WR_PORT_PRIORITY                                               0xf

		# Port n Configuration Write Register
		#(OFFSET, MASK, VALUE)      (0XFD0706C8, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD0706C8 0x000073FF 0x0000200F
		# Register : PCTRL_4 @ 0XFD070750</p>

		# Enables port n.
		# PSU_DDRC_PCTRL_4_PORT_EN                                                        0x1

		# Port n Control Register
		#(OFFSET, MASK, VALUE)      (0XFD070750, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070750 0x00000001 0x00000001
		# Register : PCFGQOS0_4 @ 0XFD070754</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0 : LPR, 1: VPR, 2: HPR. For dual address queue configurations, region1
    #  maps to the blue address queue. In this case, valid values are 0: LPR a
    # nd 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tra
    # ffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_4_RQOS_MAP_REGION1                                            0x1

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: LPR, 1: VPR, 2: HPR. For dual address queue configurations, region 0
    #  maps to the blue address queue. In this case, valid values are: 0: LPR
    # and 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tr
    # affic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_4_RQOS_MAP_REGION0                                            0x0

		# Separation level1 indicating the end of region0 mapping; start of region
    # 0 is 0. Possible values for level1 are 0 to 13 (for dual RAQ) or 0 to 14
    #  (for single RAQ) which corresponds to arqos. Note that for PA, arqos va
    # lues are used directly as port priorities, where the higher the value co
    # rresponds to higher port priority. All of the map_level* registers must
    # be set to distinct values.
		# PSU_DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1                                             0x3

		# Port n Read QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070754, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD070754 0x0033000F 0x00100003
		# Register : PCFGQOS1_4 @ 0XFD070758</p>

		# Specifies the timeout value for transactions mapped to the red address q
    # ueue.
		# PSU_DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR                                           0x0

		# Specifies the timeout value for transactions mapped to the blue address
    # queue.
		# PSU_DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB                                           0x4f

		# Port n Read QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070758, 0x07FF07FFU ,0x0000004FU)  */
    mask_write 0XFD070758 0x07FF07FF 0x0000004F
		# Register : PCFGWQOS0_4 @ 0XFD07075C</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0: NPW, 1: VPW. When VPW support is disabled (UMCTL2_VPW_EN = 0) and tr
    # affic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW
    #  traffic.
		# PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1                                           0x1

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: NPW, 1: VPW. When VPW support is disabled (UMCTL2_VPW_EN = 0) and tr
    # affic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW
    # traffic.
		# PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0                                           0x0

		# Separation level indicating the end of region0 mapping; start of region0
    #  is 0. Possible values for level1 are 0 to 14 which corresponds to awqos
    # . Note that for PA, awqos values are used directly as port priorities, w
    # here the higher the value corresponds to higher port priority.
		# PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL                                             0x3

		# Port n Write QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD07075C, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD07075C 0x0033000F 0x00100003
		# Register : PCFGWQOS1_4 @ 0XFD070760</p>

		# Specifies the timeout value for write transactions.
		# PSU_DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT                                           0x4f

		# Port n Write QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070760, 0x000007FFU ,0x0000004FU)  */
    mask_write 0XFD070760 0x000007FF 0x0000004F
		# Register : PCFGR_5 @ 0XFD070774</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (arurgent). When ena
    # bled and arurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DD
    # RC is asserted if enabled in PCCFG.go2critical_en register. Note that ar
    # urgent signal can be asserted anytime and as long as required which is i
    # ndependent of address handshaking (it is not associated with any particu
    # lar command).
		# PSU_DDRC_PCFGR_5_RD_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the read channel of the port.
		# PSU_DDRC_PCFGR_5_RD_PORT_AGING_EN                                               0x0

		# Determines the initial load value of read aging counters. These counters
    #  will be parallel loaded after reset, or after each grant to the corresp
    # onding port. The aging counters down-count every clock cycle where the p
    # ort is requesting but not granted. The higher significant 5-bits of the
    # read aging counter sets the priority of the read channel of a given port
    # . Port's priority will increase as the higher significant 5-bits of the
    # counter starts to decrease. When the aging counter becomes 0, the corres
    # ponding port channel will have the highest priority level (timeout condi
    # tion - Priority0). For multi-port configurations, the aging counters can
    # not be used to set port priorities when external dynamic priority inputs
    #  (arqos) are enabled (timeout is still applicable). For single port conf
    # igurations, the aging counters are only used when they timeout (become 0
    # ) to force read-write direction switching. In this case, external dynami
    # c priority input, arqos (for reads only) can still be used to set the DD
    # RC read priority (2 priority levels: low priority read - LPR, high prior
    # ity read - HPR) on a command by command basis. Note: The two LSBs of thi
    # s register field are tied internally to 2'b00.
		# PSU_DDRC_PCFGR_5_RD_PORT_PRIORITY                                               0xf

		# Port n Configuration Read Register
		#(OFFSET, MASK, VALUE)      (0XFD070774, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070774 0x000073FF 0x0000200F
		# Register : PCFGW_5 @ 0XFD070778</p>

		# If set to 1, enables the Page Match feature. If enabled, once a requesti
    # ng port is granted, the port is continued to be granted if the following
    #  immediate commands are to the same memory page (same bank and same row)
    # . See also related PCCFG.pagematch_limit register.
		# PSU_DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN                                           0x0

		# If set to 1, enables the AXI urgent sideband signal (awurgent). When ena
    # bled and awurgent is asserted by the master, that port becomes the highe
    # st priority and co_gs_go2critical_wr signal to DDRC is asserted if enabl
    # ed in PCCFG.go2critical_en register. Note that awurgent signal can be as
    # serted anytime and as long as required which is independent of address h
    # andshaking (it is not associated with any particular command).
		# PSU_DDRC_PCFGW_5_WR_PORT_URGENT_EN                                              0x1

		# If set to 1, enables aging function for the write channel of the port.
		# PSU_DDRC_PCFGW_5_WR_PORT_AGING_EN                                               0x0

		# Determines the initial load value of write aging counters. These counter
    # s will be parallel loaded after reset, or after each grant to the corres
    # ponding port. The aging counters down-count every clock cycle where the
    # port is requesting but not granted. The higher significant 5-bits of the
    #  write aging counter sets the initial priority of the write channel of a
    #  given port. Port's priority will increase as the higher significant 5-b
    # its of the counter starts to decrease. When the aging counter becomes 0,
    #  the corresponding port channel will have the highest priority level. Fo
    # r multi-port configurations, the aging counters cannot be used to set po
    # rt priorities when external dynamic priority inputs (awqos) are enabled
    # (timeout is still applicable). For single port configurations, the aging
    #  counters are only used when they timeout (become 0) to force read-write
    #  direction switching. Note: The two LSBs of this register field are tied
    #  internally to 2'b00.
		# PSU_DDRC_PCFGW_5_WR_PORT_PRIORITY                                               0xf

		# Port n Configuration Write Register
		#(OFFSET, MASK, VALUE)      (0XFD070778, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070778 0x000073FF 0x0000200F
		# Register : PCTRL_5 @ 0XFD070800</p>

		# Enables port n.
		# PSU_DDRC_PCTRL_5_PORT_EN                                                        0x1

		# Port n Control Register
		#(OFFSET, MASK, VALUE)      (0XFD070800, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070800 0x00000001 0x00000001
		# Register : PCFGQOS0_5 @ 0XFD070804</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0 : LPR, 1: VPR, 2: HPR. For dual address queue configurations, region1
    #  maps to the blue address queue. In this case, valid values are 0: LPR a
    # nd 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tra
    # ffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_5_RQOS_MAP_REGION1                                            0x1

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: LPR, 1: VPR, 2: HPR. For dual address queue configurations, region 0
    #  maps to the blue address queue. In this case, valid values are: 0: LPR
    # and 1: VPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and tr
    # affic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR
    # traffic.
		# PSU_DDRC_PCFGQOS0_5_RQOS_MAP_REGION0                                            0x0

		# Separation level1 indicating the end of region0 mapping; start of region
    # 0 is 0. Possible values for level1 are 0 to 13 (for dual RAQ) or 0 to 14
    #  (for single RAQ) which corresponds to arqos. Note that for PA, arqos va
    # lues are used directly as port priorities, where the higher the value co
    # rresponds to higher port priority. All of the map_level* registers must
    # be set to distinct values.
		# PSU_DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1                                             0x3

		# Port n Read QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD070804, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD070804 0x0033000F 0x00100003
		# Register : PCFGQOS1_5 @ 0XFD070808</p>

		# Specifies the timeout value for transactions mapped to the red address q
    # ueue.
		# PSU_DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR                                           0x0

		# Specifies the timeout value for transactions mapped to the blue address
    # queue.
		# PSU_DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB                                           0x4f

		# Port n Read QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070808, 0x07FF07FFU ,0x0000004FU)  */
    mask_write 0XFD070808 0x07FF07FF 0x0000004F
		# Register : PCFGWQOS0_5 @ 0XFD07080C</p>

		# This bitfield indicates the traffic class of region 1. Valid values are:
    #  0: NPW, 1: VPW. When VPW support is disabled (UMCTL2_VPW_EN = 0) and tr
    # affic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW
    #  traffic.
		# PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1                                           0x1

		# This bitfield indicates the traffic class of region 0. Valid values are:
    #  0: NPW, 1: VPW. When VPW support is disabled (UMCTL2_VPW_EN = 0) and tr
    # affic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW
    # traffic.
		# PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0                                           0x0

		# Separation level indicating the end of region0 mapping; start of region0
    #  is 0. Possible values for level1 are 0 to 14 which corresponds to awqos
    # . Note that for PA, awqos values are used directly as port priorities, w
    # here the higher the value corresponds to higher port priority.
		# PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL                                             0x3

		# Port n Write QoS Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD07080C, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD07080C 0x0033000F 0x00100003
		# Register : PCFGWQOS1_5 @ 0XFD070810</p>

		# Specifies the timeout value for write transactions.
		# PSU_DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT                                           0x4f

		# Port n Write QoS Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD070810, 0x000007FFU ,0x0000004FU)  */
    mask_write 0XFD070810 0x000007FF 0x0000004F
		# Register : SARBASE0 @ 0XFD070F04</p>

		# Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x
    # ] and araddr[UMCTL2_A_ADDRW-1:x] where x is determined by the minimum bl
    # ock size parameter UMCTL2_SARMINSIZE: (x=log2(block size)).
		# PSU_DDRC_SARBASE0_BASE_ADDR                                                     0x0

		# SAR Base Address Register n
		#(OFFSET, MASK, VALUE)      (0XFD070F04, 0x000001FFU ,0x00000000U)  */
    mask_write 0XFD070F04 0x000001FF 0x00000000
		# Register : SARSIZE0 @ 0XFD070F08</p>

		# Number of blocks for address region n. This register determines the tota
    # l size of the region in multiples of minimum block size as specified by
    # the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded
    # as number of blocks = nblocks + 1. For example, if register is programme
    # d to 0, region will have 1 block.
		# PSU_DDRC_SARSIZE0_NBLOCKS                                                       0x0

		# SAR Size Register n
		#(OFFSET, MASK, VALUE)      (0XFD070F08, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD070F08 0x000000FF 0x00000000
		# Register : SARBASE1 @ 0XFD070F0C</p>

		# Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x
    # ] and araddr[UMCTL2_A_ADDRW-1:x] where x is determined by the minimum bl
    # ock size parameter UMCTL2_SARMINSIZE: (x=log2(block size)).
		# PSU_DDRC_SARBASE1_BASE_ADDR                                                     0x10

		# SAR Base Address Register n
		#(OFFSET, MASK, VALUE)      (0XFD070F0C, 0x000001FFU ,0x00000010U)  */
    mask_write 0XFD070F0C 0x000001FF 0x00000010
		# Register : SARSIZE1 @ 0XFD070F10</p>

		# Number of blocks for address region n. This register determines the tota
    # l size of the region in multiples of minimum block size as specified by
    # the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded
    # as number of blocks = nblocks + 1. For example, if register is programme
    # d to 0, region will have 1 block.
		# PSU_DDRC_SARSIZE1_NBLOCKS                                                       0xf

		# SAR Size Register n
		#(OFFSET, MASK, VALUE)      (0XFD070F10, 0x000000FFU ,0x0000000FU)  */
    mask_write 0XFD070F10 0x000000FF 0x0000000F
		# Register : DFITMG0_SHADOW @ 0XFD072190</p>

		# Specifies the number of DFI clock cycles after an assertion or de-assert
    # ion of the DFI control signals that the control signals at the PHY-DRAM
    # interface reflect the assertion or de-assertion. If the DFI clock and th
    # e memory clock are not phase-aligned, this timing parameter should be ro
    # unded up to the next integer value. Note that if using RDIMM, it is nece
    # ssary to increment this parameter by RDIMM's extra cycle of latency in t
    # erms of DFI clock.
		# PSU_DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY                                        0x7

		# Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated u
    # sing HDR or SDR values Selects whether value in DFITMG0.dfi_t_rddata_en
    # is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles
    #  - 1 in terms of SDR clock cycles Refer to PHY specification for correct
    #  value.
		# PSU_DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR                                      0x1

		# Time from the assertion of a read command on the DFI interface to the as
    # sertion of the dfi_rddata_en signal. Refer to PHY specification for corr
    # ect value. This corresponds to the DFI parameter trddata_en. Note that,
    # depending on the PHY, if using RDIMM, it may be necessary to use the val
    # ue (CL + 1) in the calculation of trddata_en. This is to compensate for
    # the extra cycle of latency through the RDIMM. Unit: Clocks
		# PSU_DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN                                         0x2

		# Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated us
    # ing HDR or SDR values Selects whether value in DFITMG0.dfi_tphy_wrlat is
    #  in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.df
    # i_tphy_wrdata is in terms of SDR or HDR clock cycles - 0 in terms of HDR
    #  clock cycles - 1 in terms of SDR clock cycles Refer to PHY specificatio
    # n for correct value.
		# PSU_DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR                                      0x1

		# Specifies the number of clock cycles between when dfi_wrdata_en is asser
    # ted to when the associated write data is driven on the dfi_wrdata signal
    # . This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY
    #  specification for correct value. Note, max supported value is 8. Unit:
    # Clocks
		# PSU_DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA                                         0x0

		# Write latency Number of clocks from the write command to write data enab
    # le (dfi_wrdata_en). This corresponds to the DFI timing parameter tphy_wr
    # lat. Refer to PHY specification for correct value.Note that, depending o
    # n the PHY, if using RDIMM, it may be necessary to use the value (CL + 1)
    #  in the calculation of tphy_wrlat. This is to compensate for the extra c
    # ycle of latency through the RDIMM.
		# PSU_DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT                                          0x2

		# DFI Timing Shadow Register 0
		#(OFFSET, MASK, VALUE)      (0XFD072190, 0x1FBFBF3FU ,0x07828002U)  */
    mask_write 0XFD072190 0x1FBFBF3F 0x07828002
		# : DDR CONTROLLER RESET
		# Register : RST_DDR_SS @ 0XFD1A0108</p>

		# DDR block level reset inside of the DDR Sub System
		# PSU_CRF_APB_RST_DDR_SS_DDR_RESET                                                0X0

		# APM block level reset inside of the DDR Sub System
		# PSU_CRF_APB_RST_DDR_SS_APM_RESET                                                0X0

		# DDR sub system block level reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0108, 0x0000000CU ,0x00000000U)  */
    mask_write 0XFD1A0108 0x0000000C 0x00000000
		# : DDR PHY
		# Register : PGCR0 @ 0XFD080010</p>

		# Address Copy
		# PSU_DDR_PHY_PGCR0_ADCP                                                          0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_PGCR0_RESERVED_30_27                                                0x0

		# PHY FIFO Reset
		# PSU_DDR_PHY_PGCR0_PHYFRST                                                       0x1

		# Oscillator Mode Address/Command Delay Line Select
		# PSU_DDR_PHY_PGCR0_OSCACDL                                                       0x3

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_PGCR0_RESERVED_23_19                                                0x0

		# Digital Test Output Select
		# PSU_DDR_PHY_PGCR0_DTOSEL                                                        0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_PGCR0_RESERVED_13                                                   0x0

		# Oscillator Mode Division
		# PSU_DDR_PHY_PGCR0_OSCDIV                                                        0xf

		# Oscillator Enable
		# PSU_DDR_PHY_PGCR0_OSCEN                                                         0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_PGCR0_RESERVED_7_0                                                  0x0

		# PHY General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080010, 0xFFFFFFFFU ,0x07001E00U)  */
    mask_write 0XFD080010 0xFFFFFFFF 0x07001E00
		# Register : PGCR2 @ 0XFD080018</p>

		# Clear Training Status Registers
		# PSU_DDR_PHY_PGCR2_CLRTSTAT                                                      0x0

		# Clear Impedance Calibration
		# PSU_DDR_PHY_PGCR2_CLRZCAL                                                       0x0

		# Clear Parity Error
		# PSU_DDR_PHY_PGCR2_CLRPERR                                                       0x0

		# Initialization Complete Pin Configuration
		# PSU_DDR_PHY_PGCR2_ICPC                                                          0x0

		# Data Training PUB Mode Exit Timer
		# PSU_DDR_PHY_PGCR2_DTPMXTMR                                                      0xf

		# Initialization Bypass
		# PSU_DDR_PHY_PGCR2_INITFSMBYP                                                    0x0

		# PLL FSM Bypass
		# PSU_DDR_PHY_PGCR2_PLLFSMBYP                                                     0x0

		# Refresh Period
		# PSU_DDR_PHY_PGCR2_TREFPRD                                                       0x10010

		# PHY General Configuration Register 2
		#(OFFSET, MASK, VALUE)      (0XFD080018, 0xFFFFFFFFU ,0x00F10010U)  */
    mask_write 0XFD080018 0xFFFFFFFF 0x00F10010
		# Register : PGCR3 @ 0XFD08001C</p>

		# CKN Enable
		# PSU_DDR_PHY_PGCR3_CKNEN                                                         0x55

		# CK Enable
		# PSU_DDR_PHY_PGCR3_CKEN                                                          0xaa

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_PGCR3_RESERVED_15                                                   0x0

		# Enable Clock Gating for AC [0] ctl_rd_clk
		# PSU_DDR_PHY_PGCR3_GATEACRDCLK                                                   0x2

		# Enable Clock Gating for AC [0] ddr_clk
		# PSU_DDR_PHY_PGCR3_GATEACDDRCLK                                                  0x2

		# Enable Clock Gating for AC [0] ctl_clk
		# PSU_DDR_PHY_PGCR3_GATEACCTLCLK                                                  0x2

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_PGCR3_RESERVED_8                                                    0x0

		# Controls DDL Bypass Modes
		# PSU_DDR_PHY_PGCR3_DDLBYPMODE                                                    0x2

		# IO Loop-Back Select
		# PSU_DDR_PHY_PGCR3_IOLB                                                          0x0

		# AC Receive FIFO Read Mode
		# PSU_DDR_PHY_PGCR3_RDMODE                                                        0x0

		# Read FIFO Reset Disable
		# PSU_DDR_PHY_PGCR3_DISRST                                                        0x0

		# Clock Level when Clock Gating
		# PSU_DDR_PHY_PGCR3_CLKLEVEL                                                      0x0

		# PHY General Configuration Register 3
		#(OFFSET, MASK, VALUE)      (0XFD08001C, 0xFFFFFFFFU ,0x55AA5480U)  */
    mask_write 0XFD08001C 0xFFFFFFFF 0x55AA5480
		# Register : PGCR5 @ 0XFD080024</p>

		# Frequency B Ratio Term
		# PSU_DDR_PHY_PGCR5_FRQBT                                                         0x1

		# Frequency A Ratio Term
		# PSU_DDR_PHY_PGCR5_FRQAT                                                         0x1

		# DFI Disconnect Time Period
		# PSU_DDR_PHY_PGCR5_DISCNPERIOD                                                   0x0

		# Receiver bias core side control
		# PSU_DDR_PHY_PGCR5_VREF_RBCTRL                                                   0xf

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_PGCR5_RESERVED_3                                                    0x0

		# Internal VREF generator REFSEL ragne select
		# PSU_DDR_PHY_PGCR5_DXREFISELRANGE                                                0x1

		# DDL Page Read Write select
		# PSU_DDR_PHY_PGCR5_DDLPGACT                                                      0x0

		# DDL Page Read Write select
		# PSU_DDR_PHY_PGCR5_DDLPGRW                                                       0x0

		# PHY General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080024, 0xFFFFFFFFU ,0x010100F4U)  */
    mask_write 0XFD080024 0xFFFFFFFF 0x010100F4
		# Register : PTR0 @ 0XFD080040</p>

		# PLL Power-Down Time
		# PSU_DDR_PHY_PTR0_TPLLPD                                                         0x56

		# PLL Gear Shift Time
		# PSU_DDR_PHY_PTR0_TPLLGS                                                         0x2155

		# PHY Reset Time
		# PSU_DDR_PHY_PTR0_TPHYRST                                                        0x10

		# PHY Timing Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080040, 0xFFFFFFFFU ,0x0AC85550U)  */
    mask_write 0XFD080040 0xFFFFFFFF 0x0AC85550
		# Register : PTR1 @ 0XFD080044</p>

		# PLL Lock Time
		# PSU_DDR_PHY_PTR1_TPLLLOCK                                                       0x4141

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_PTR1_RESERVED_15_13                                                 0x0

		# PLL Reset Time
		# PSU_DDR_PHY_PTR1_TPLLRST                                                        0xaff

		# PHY Timing Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080044, 0xFFFFFFFFU ,0x41410AFFU)  */
    mask_write 0XFD080044 0xFFFFFFFF 0x41410AFF
		# Register : PLLCR0 @ 0XFD080068</p>

		# PLL Bypass
		# PSU_DDR_PHY_PLLCR0_PLLBYP                                                       0x0

		# PLL Reset
		# PSU_DDR_PHY_PLLCR0_PLLRST                                                       0x0

		# PLL Power Down
		# PSU_DDR_PHY_PLLCR0_PLLPD                                                        0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_PLLCR0_RSTOPM                                                       0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_PLLCR0_FRQSEL                                                       0x1

		# Relock Mode
		# PSU_DDR_PHY_PLLCR0_RLOCKM                                                       0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_PLLCR0_CPPC                                                         0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_PLLCR0_CPIC                                                         0x0

		# Gear Shift
		# PSU_DDR_PHY_PLLCR0_GSHIFT                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_PLLCR0_RESERVED_11_9                                                0x0

		# Analog Test Enable
		# PSU_DDR_PHY_PLLCR0_ATOEN                                                        0x0

		# Analog Test Control
		# PSU_DDR_PHY_PLLCR0_ATC                                                          0x0

		# Digital Test Control
		# PSU_DDR_PHY_PLLCR0_DTC                                                          0x0

		# PLL Control Register 0 (Type B PLL Only)
		#(OFFSET, MASK, VALUE)      (0XFD080068, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD080068 0xFFFFFFFF 0x01100000
		# Register : DSGCR @ 0XFD080090</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DSGCR_RESERVED_31_28                                                0x0

		# When RDBI enabled, this bit is used to select RDBI CL calculation, if it
    #  is 1b1, calculation will use RDBICL, otherwise use default calculation.
		# PSU_DDR_PHY_DSGCR_RDBICLSEL                                                     0x0

		# When RDBI enabled, if RDBICLSEL is asserted, RDBI CL adjust using this v
    # alue.
		# PSU_DDR_PHY_DSGCR_RDBICL                                                        0x2

		# PHY Impedance Update Enable
		# PSU_DDR_PHY_DSGCR_PHYZUEN                                                       0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DSGCR_RESERVED_22                                                   0x0

		# SDRAM Reset Output Enable
		# PSU_DDR_PHY_DSGCR_RSTOE                                                         0x1

		# Single Data Rate Mode
		# PSU_DDR_PHY_DSGCR_SDRMODE                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DSGCR_RESERVED_18                                                   0x0

		# ATO Analog Test Enable
		# PSU_DDR_PHY_DSGCR_ATOAE                                                         0x0

		# DTO Output Enable
		# PSU_DDR_PHY_DSGCR_DTOOE                                                         0x0

		# DTO I/O Mode
		# PSU_DDR_PHY_DSGCR_DTOIOM                                                        0x0

		# DTO Power Down Receiver
		# PSU_DDR_PHY_DSGCR_DTOPDR                                                        0x1

		# Reserved. Return zeroes on reads
		# PSU_DDR_PHY_DSGCR_RESERVED_13                                                   0x0

		# DTO On-Die Termination
		# PSU_DDR_PHY_DSGCR_DTOODT                                                        0x0

		# PHY Update Acknowledge Delay
		# PSU_DDR_PHY_DSGCR_PUAD                                                          0x5

		# Controller Update Acknowledge Enable
		# PSU_DDR_PHY_DSGCR_CUAEN                                                         0x1

		# Reserved. Return zeroes on reads
		# PSU_DDR_PHY_DSGCR_RESERVED_4_3                                                  0x0

		# Controller Impedance Update Enable
		# PSU_DDR_PHY_DSGCR_CTLZUEN                                                       0x0

		# Reserved. Return zeroes on reads
		# PSU_DDR_PHY_DSGCR_RESERVED_1                                                    0x0

		# PHY Update Request Enable
		# PSU_DDR_PHY_DSGCR_PUREN                                                         0x1

		# DDR System General Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD080090, 0xFFFFFFFFU ,0x02A04161U)  */
    mask_write 0XFD080090 0xFFFFFFFF 0x02A04161
		# Register : GPR0 @ 0XFD0800C0</p>

		# General Purpose Register 0
		# PSU_DDR_PHY_GPR0_GPR0                                                           0xd3

		# General Purpose Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0800C0, 0xFFFFFFFFU ,0x000000D3U)  */
    mask_write 0XFD0800C0 0xFFFFFFFF 0x000000D3
		# Register : DCR @ 0XFD080100</p>

		# DDR4 Gear Down Timing.
		# PSU_DDR_PHY_DCR_GEARDN                                                          0x0

		# Un-used Bank Group
		# PSU_DDR_PHY_DCR_UBG                                                             0x0

		# Un-buffered DIMM Address Mirroring
		# PSU_DDR_PHY_DCR_UDIMM                                                           0x0

		# DDR 2T Timing
		# PSU_DDR_PHY_DCR_DDR2T                                                           0x0

		# No Simultaneous Rank Access
		# PSU_DDR_PHY_DCR_NOSRA                                                           0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DCR_RESERVED_26_18                                                  0x0

		# Byte Mask
		# PSU_DDR_PHY_DCR_BYTEMASK                                                        0x1

		# DDR Type
		# PSU_DDR_PHY_DCR_DDRTYPE                                                         0x0

		# Multi-Purpose Register (MPR) DQ (DDR3 Only)
		# PSU_DDR_PHY_DCR_MPRDQ                                                           0x0

		# Primary DQ (DDR3 Only)
		# PSU_DDR_PHY_DCR_PDQ                                                             0x0

		# DDR 8-Bank
		# PSU_DDR_PHY_DCR_DDR8BNK                                                         0x1

		# DDR Mode
		# PSU_DDR_PHY_DCR_DDRMD                                                           0x4

		# DRAM Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD080100, 0xFFFFFFFFU ,0x0800040CU)  */
    mask_write 0XFD080100 0xFFFFFFFF 0x0800040C
		# Register : DTPR0 @ 0XFD080110</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR0_RESERVED_31_29                                                0x0

		# Activate to activate command delay (different banks)
		# PSU_DDR_PHY_DTPR0_TRRD                                                          0x6

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR0_RESERVED_23                                                   0x0

		# Activate to precharge command delay
		# PSU_DDR_PHY_DTPR0_TRAS                                                          0x24

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR0_RESERVED_15                                                   0x0

		# Precharge command period
		# PSU_DDR_PHY_DTPR0_TRP                                                           0xf

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR0_RESERVED_7_5                                                  0x0

		# Internal read to precharge command delay
		# PSU_DDR_PHY_DTPR0_TRTP                                                          0x8

		# DRAM Timing Parameters Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080110, 0xFFFFFFFFU ,0x06240F08U)  */
    mask_write 0XFD080110 0xFFFFFFFF 0x06240F08
		# Register : DTPR1 @ 0XFD080114</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR1_RESERVED_31                                                   0x0

		# Minimum delay from when write leveling mode is programmed to the first D
    # QS/DQS# rising edge.
		# PSU_DDR_PHY_DTPR1_TWLMRD                                                        0x28

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR1_RESERVED_23                                                   0x0

		# 4-bank activate period
		# PSU_DDR_PHY_DTPR1_TFAW                                                          0x20

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR1_RESERVED_15_11                                                0x0

		# Load mode update delay (DDR4 and DDR3 only)
		# PSU_DDR_PHY_DTPR1_TMOD                                                          0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR1_RESERVED_7_5                                                  0x0

		# Load mode cycle time
		# PSU_DDR_PHY_DTPR1_TMRD                                                          0x8

		# DRAM Timing Parameters Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080114, 0xFFFFFFFFU ,0x28200008U)  */
    mask_write 0XFD080114 0xFFFFFFFF 0x28200008
		# Register : DTPR2 @ 0XFD080118</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR2_RESERVED_31_29                                                0x0

		# Read to Write command delay. Valid values are
		# PSU_DDR_PHY_DTPR2_TRTW                                                          0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR2_RESERVED_27_25                                                0x0

		# Read to ODT delay (DDR3 only)
		# PSU_DDR_PHY_DTPR2_TRTODT                                                        0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR2_RESERVED_23_20                                                0x0

		# CKE minimum pulse width
		# PSU_DDR_PHY_DTPR2_TCKE                                                          0x7

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR2_RESERVED_15_10                                                0x0

		# Self refresh exit delay
		# PSU_DDR_PHY_DTPR2_TXS                                                           0x300

		# DRAM Timing Parameters Register 2
		#(OFFSET, MASK, VALUE)      (0XFD080118, 0xFFFFFFFFU ,0x00070300U)  */
    mask_write 0XFD080118 0xFFFFFFFF 0x00070300
		# Register : DTPR3 @ 0XFD08011C</p>

		# ODT turn-off delay extension
		# PSU_DDR_PHY_DTPR3_TOFDX                                                         0x4

		# Read to read and write to write command delay
		# PSU_DDR_PHY_DTPR3_TCCD                                                          0x0

		# DLL locking time
		# PSU_DDR_PHY_DTPR3_TDLLK                                                         0x300

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR3_RESERVED_15_12                                                0x0

		# Maximum DQS output access time from CK/CK# (LPDDR2/3 only)
		# PSU_DDR_PHY_DTPR3_TDQSCKMAX                                                     0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR3_RESERVED_7_3                                                  0x0

		# DQS output access time from CK/CK# (LPDDR2/3 only)
		# PSU_DDR_PHY_DTPR3_TDQSCK                                                        0x0

		# DRAM Timing Parameters Register 3
		#(OFFSET, MASK, VALUE)      (0XFD08011C, 0xFFFFFFFFU ,0x83000800U)  */
    mask_write 0XFD08011C 0xFFFFFFFF 0x83000800
		# Register : DTPR4 @ 0XFD080120</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR4_RESERVED_31_30                                                0x0

		# ODT turn-on/turn-off delays (DDR2 only)
		# PSU_DDR_PHY_DTPR4_TAOND_TAOFD                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR4_RESERVED_27_26                                                0x0

		# Refresh-to-Refresh
		# PSU_DDR_PHY_DTPR4_TRFC                                                          0x116

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR4_RESERVED_15_14                                                0x0

		# Write leveling output delay
		# PSU_DDR_PHY_DTPR4_TWLO                                                          0x2b

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR4_RESERVED_7_5                                                  0x0

		# Power down exit delay
		# PSU_DDR_PHY_DTPR4_TXP                                                           0x7

		# DRAM Timing Parameters Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080120, 0xFFFFFFFFU ,0x01162B07U)  */
    mask_write 0XFD080120 0xFFFFFFFF 0x01162B07
		# Register : DTPR5 @ 0XFD080124</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR5_RESERVED_31_24                                                0x0

		# Activate to activate command delay (same bank)
		# PSU_DDR_PHY_DTPR5_TRC                                                           0x33

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR5_RESERVED_15                                                   0x0

		# Activate to read or write delay
		# PSU_DDR_PHY_DTPR5_TRCD                                                          0xf

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR5_RESERVED_7_5                                                  0x0

		# Internal write to read command delay
		# PSU_DDR_PHY_DTPR5_TWTR                                                          0x8

		# DRAM Timing Parameters Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080124, 0xFFFFFFFFU ,0x00330F08U)  */
    mask_write 0XFD080124 0xFFFFFFFF 0x00330F08
		# Register : DTPR6 @ 0XFD080128</p>

		# PUB Write Latency Enable
		# PSU_DDR_PHY_DTPR6_PUBWLEN                                                       0x0

		# PUB Read Latency Enable
		# PSU_DDR_PHY_DTPR6_PUBRLEN                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR6_RESERVED_29_14                                                0x0

		# Write Latency
		# PSU_DDR_PHY_DTPR6_PUBWL                                                         0xe

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTPR6_RESERVED_7_6                                                  0x0

		# Read Latency
		# PSU_DDR_PHY_DTPR6_PUBRL                                                         0xf

		# DRAM Timing Parameters Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080128, 0xFFFFFFFFU ,0x00000E0FU)  */
    mask_write 0XFD080128 0xFFFFFFFF 0x00000E0F
		# Register : RDIMMGCR0 @ 0XFD080140</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RESERVED_31                                               0x0

		# RDMIMM Quad CS Enable
		# PSU_DDR_PHY_RDIMMGCR0_QCSEN                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RESERVED_29_28                                            0x0

		# RDIMM Outputs I/O Mode
		# PSU_DDR_PHY_RDIMMGCR0_RDIMMIOM                                                  0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RESERVED_26_24                                            0x0

		# ERROUT# Output Enable
		# PSU_DDR_PHY_RDIMMGCR0_ERROUTOE                                                  0x0

		# ERROUT# I/O Mode
		# PSU_DDR_PHY_RDIMMGCR0_ERROUTIOM                                                 0x1

		# ERROUT# Power Down Receiver
		# PSU_DDR_PHY_RDIMMGCR0_ERROUTPDR                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RESERVED_20                                               0x0

		# ERROUT# On-Die Termination
		# PSU_DDR_PHY_RDIMMGCR0_ERROUTODT                                                 0x0

		# Load Reduced DIMM
		# PSU_DDR_PHY_RDIMMGCR0_LRDIMM                                                    0x0

		# PAR_IN I/O Mode
		# PSU_DDR_PHY_RDIMMGCR0_PARINIOM                                                  0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RESERVED_16_8                                             0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD                                             0x0

		# Rank Mirror Enable.
		# PSU_DDR_PHY_RDIMMGCR0_RNKMRREN                                                  0x2

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR0_RESERVED_3                                                0x0

		# Stop on Parity Error
		# PSU_DDR_PHY_RDIMMGCR0_SOPERR                                                    0x0

		# Parity Error No Registering
		# PSU_DDR_PHY_RDIMMGCR0_ERRNOREG                                                  0x0

		# Registered DIMM
		# PSU_DDR_PHY_RDIMMGCR0_RDIMM                                                     0x0

		# RDIMM General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080140, 0xFFFFFFFFU ,0x08400020U)  */
    mask_write 0XFD080140 0xFFFFFFFF 0x08400020
		# Register : RDIMMGCR1 @ 0XFD080144</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR1_RESERVED_31_29                                            0x0

		# Address [17] B-side Inversion Disable
		# PSU_DDR_PHY_RDIMMGCR1_A17BID                                                    0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR1_RESERVED_27                                               0x0

		# Command word to command word programming delay
		# PSU_DDR_PHY_RDIMMGCR1_TBCMRD_L2                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR1_RESERVED_23                                               0x0

		# Command word to command word programming delay
		# PSU_DDR_PHY_RDIMMGCR1_TBCMRD_L                                                  0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR1_RESERVED_19                                               0x0

		# Command word to command word programming delay
		# PSU_DDR_PHY_RDIMMGCR1_TBCMRD                                                    0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RDIMMGCR1_RESERVED_15_14                                            0x0

		# Stabilization time
		# PSU_DDR_PHY_RDIMMGCR1_TBCSTAB                                                   0xc80

		# RDIMM General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080144, 0xFFFFFFFFU ,0x00000C80U)  */
    mask_write 0XFD080144 0xFFFFFFFF 0x00000C80
		# Register : RDIMMCR0 @ 0XFD080150</p>

		# DDR4/DDR3 Control Word 7
		# PSU_DDR_PHY_RDIMMCR0_RC7                                                        0x0

		# DDR4 Control Word 6 (Comman space Control Word) / DDR3 Reserved
		# PSU_DDR_PHY_RDIMMCR0_RC6                                                        0x0

		# DDR4/DDR3 Control Word 5 (CK Driver Characteristics Control Word)
		# PSU_DDR_PHY_RDIMMCR0_RC5                                                        0x0

		# DDR4 Control Word 4 (ODT and CKE Signals Driver Characteristics Control
    # Word) / DDR3 Control Word 4 (Control Signals Driver Characteristics Cont
    # rol Word)
		# PSU_DDR_PHY_RDIMMCR0_RC4                                                        0x0

		# DDR4 Control Word 3 (CA and CS Signals Driver Characteristics Control Wo
    # rd) / DDR3 Control Word 3 (Command/Address Signals Driver Characteristri
    # cs Control Word)
		# PSU_DDR_PHY_RDIMMCR0_RC3                                                        0x0

		# DDR4 Control Word 2 (Timing and IBT Control Word) / DDR3 Control Word 2
    # (Timing Control Word)
		# PSU_DDR_PHY_RDIMMCR0_RC2                                                        0x0

		# DDR4/DDR3 Control Word 1 (Clock Driver Enable Control Word)
		# PSU_DDR_PHY_RDIMMCR0_RC1                                                        0x0

		# DDR4/DDR3 Control Word 0 (Global Features Control Word)
		# PSU_DDR_PHY_RDIMMCR0_RC0                                                        0x0

		# RDIMM Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080150, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080150 0xFFFFFFFF 0x00000000
		# Register : RDIMMCR1 @ 0XFD080154</p>

		# Control Word 15
		# PSU_DDR_PHY_RDIMMCR1_RC15                                                       0x0

		# DDR4 Control Word 14 (Parity Control Word) / DDR3 Reserved
		# PSU_DDR_PHY_RDIMMCR1_RC14                                                       0x0

		# DDR4 Control Word 13 (DIMM Configuration Control Word) / DDR3 Reserved
		# PSU_DDR_PHY_RDIMMCR1_RC13                                                       0x0

		# DDR4 Control Word 12 (Training Control Word) / DDR3 Reserved
		# PSU_DDR_PHY_RDIMMCR1_RC12                                                       0x0

		# DDR4 Control Word 11 (Operating Voltage VDD and VREFCA Source Control Wo
    # rd) / DDR3 Control Word 11 (Operation Voltage VDD Control Word)
		# PSU_DDR_PHY_RDIMMCR1_RC11                                                       0x0

		# DDR4/DDR3 Control Word 10 (RDIMM Operating Speed Control Word)
		# PSU_DDR_PHY_RDIMMCR1_RC10                                                       0x2

		# DDR4/DDR3 Control Word 9 (Power Saving Settings Control Word)
		# PSU_DDR_PHY_RDIMMCR1_RC9                                                        0x0

		# DDR4 Control Word 8 (Input/Output Configuration Control Word) / DDR3 Con
    # trol Word 8 (Additional Input Bus Termination Setting Control Word)
		# PSU_DDR_PHY_RDIMMCR1_RC8                                                        0x0

		# RDIMM Control Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080154, 0xFFFFFFFFU ,0x00000200U)  */
    mask_write 0XFD080154 0xFFFFFFFF 0x00000200
		# Register : MR0 @ 0XFD080180</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR0_RESERVED_31_8                                                   0x6

		# CA Terminating Rank
		# PSU_DDR_PHY_MR0_CATR                                                            0x0

		# Reserved. These are JEDEC reserved bits and are recommended by JEDEC to
    # be programmed to 0x0.
		# PSU_DDR_PHY_MR0_RSVD_6_5                                                        0x1

		# Built-in Self-Test for RZQ
		# PSU_DDR_PHY_MR0_RZQI                                                            0x2

		# Reserved. These are JEDEC reserved bits and are recommended by JEDEC to
    # be programmed to 0x0.
		# PSU_DDR_PHY_MR0_RSVD_2_0                                                        0x0

		# LPDDR4 Mode Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080180, 0xFFFFFFFFU ,0x00000630U)  */
    mask_write 0XFD080180 0xFFFFFFFF 0x00000630
		# Register : MR1 @ 0XFD080184</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR1_RESERVED_31_8                                                   0x3

		# Read Postamble Length
		# PSU_DDR_PHY_MR1_RDPST                                                           0x0

		# Write-recovery for auto-precharge command
		# PSU_DDR_PHY_MR1_NWR                                                             0x0

		# Read Preamble Length
		# PSU_DDR_PHY_MR1_RDPRE                                                           0x0

		# Write Preamble Length
		# PSU_DDR_PHY_MR1_WRPRE                                                           0x0

		# Burst Length
		# PSU_DDR_PHY_MR1_BL                                                              0x1

		# LPDDR4 Mode Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080184, 0xFFFFFFFFU ,0x00000301U)  */
    mask_write 0XFD080184 0xFFFFFFFF 0x00000301
		# Register : MR2 @ 0XFD080188</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR2_RESERVED_31_8                                                   0x0

		# Write Leveling
		# PSU_DDR_PHY_MR2_WRL                                                             0x0

		# Write Latency Set
		# PSU_DDR_PHY_MR2_WLS                                                             0x0

		# Write Latency
		# PSU_DDR_PHY_MR2_WL                                                              0x4

		# Read Latency
		# PSU_DDR_PHY_MR2_RL                                                              0x0

		# LPDDR4 Mode Register 2
		#(OFFSET, MASK, VALUE)      (0XFD080188, 0xFFFFFFFFU ,0x00000020U)  */
    mask_write 0XFD080188 0xFFFFFFFF 0x00000020
		# Register : MR3 @ 0XFD08018C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR3_RESERVED_31_8                                                   0x2

		# DBI-Write Enable
		# PSU_DDR_PHY_MR3_DBIWR                                                           0x0

		# DBI-Read Enable
		# PSU_DDR_PHY_MR3_DBIRD                                                           0x0

		# Pull-down Drive Strength
		# PSU_DDR_PHY_MR3_PDDS                                                            0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR3_RSVD                                                            0x0

		# Write Postamble Length
		# PSU_DDR_PHY_MR3_WRPST                                                           0x0

		# Pull-up Calibration Point
		# PSU_DDR_PHY_MR3_PUCAL                                                           0x0

		# LPDDR4 Mode Register 3
		#(OFFSET, MASK, VALUE)      (0XFD08018C, 0xFFFFFFFFU ,0x00000200U)  */
    mask_write 0XFD08018C 0xFFFFFFFF 0x00000200
		# Register : MR4 @ 0XFD080190</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR4_RESERVED_31_16                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR4_RSVD_15_13                                                      0x0

		# Write Preamble
		# PSU_DDR_PHY_MR4_WRP                                                             0x0

		# Read Preamble
		# PSU_DDR_PHY_MR4_RDP                                                             0x0

		# Read Preamble Training Mode
		# PSU_DDR_PHY_MR4_RPTM                                                            0x0

		# Self Refresh Abort
		# PSU_DDR_PHY_MR4_SRA                                                             0x0

		# CS to Command Latency Mode
		# PSU_DDR_PHY_MR4_CS2CMDL                                                         0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR4_RSVD1                                                           0x0

		# Internal VREF Monitor
		# PSU_DDR_PHY_MR4_IVM                                                             0x0

		# Temperature Controlled Refresh Mode
		# PSU_DDR_PHY_MR4_TCRM                                                            0x0

		# Temperature Controlled Refresh Range
		# PSU_DDR_PHY_MR4_TCRR                                                            0x0

		# Maximum Power Down Mode
		# PSU_DDR_PHY_MR4_MPDM                                                            0x0

		# This is a JEDEC reserved bit and is recommended by JEDEC to be programme
    # d to 0x0.
		# PSU_DDR_PHY_MR4_RSVD_0                                                          0x0

		# DDR4 Mode Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080190, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080190 0xFFFFFFFF 0x00000000
		# Register : MR5 @ 0XFD080194</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR5_RESERVED_31_16                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR5_RSVD                                                            0x0

		# Read DBI
		# PSU_DDR_PHY_MR5_RDBI                                                            0x0

		# Write DBI
		# PSU_DDR_PHY_MR5_WDBI                                                            0x0

		# Data Mask
		# PSU_DDR_PHY_MR5_DM                                                              0x1

		# CA Parity Persistent Error
		# PSU_DDR_PHY_MR5_CAPPE                                                           0x1

		# RTT_PARK
		# PSU_DDR_PHY_MR5_RTTPARK                                                         0x3

		# ODT Input Buffer during Power Down mode
		# PSU_DDR_PHY_MR5_ODTIBPD                                                         0x0

		# C/A Parity Error Status
		# PSU_DDR_PHY_MR5_CAPES                                                           0x0

		# CRC Error Clear
		# PSU_DDR_PHY_MR5_CRCEC                                                           0x0

		# C/A Parity Latency Mode
		# PSU_DDR_PHY_MR5_CAPM                                                            0x0

		# DDR4 Mode Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080194, 0xFFFFFFFFU ,0x000006C0U)  */
    mask_write 0XFD080194 0xFFFFFFFF 0x000006C0
		# Register : MR6 @ 0XFD080198</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR6_RESERVED_31_16                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR6_RSVD_15_13                                                      0x0

		# CAS_n to CAS_n command delay for same bank group (tCCD_L)
		# PSU_DDR_PHY_MR6_TCCDL                                                           0x2

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR6_RSVD_9_8                                                        0x0

		# VrefDQ Training Enable
		# PSU_DDR_PHY_MR6_VDDQTEN                                                         0x0

		# VrefDQ Training Range
		# PSU_DDR_PHY_MR6_VDQTRG                                                          0x0

		# VrefDQ Training Values
		# PSU_DDR_PHY_MR6_VDQTVAL                                                         0x19

		# DDR4 Mode Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080198, 0xFFFFFFFFU ,0x00000819U)  */
    mask_write 0XFD080198 0xFFFFFFFF 0x00000819
		# Register : MR11 @ 0XFD0801AC</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR11_RESERVED_31_8                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR11_RSVD                                                           0x0

		# Power Down Control
		# PSU_DDR_PHY_MR11_PDCTL                                                          0x0

		# DQ Bus Receiver On-Die-Termination
		# PSU_DDR_PHY_MR11_DQODT                                                          0x0

		# LPDDR4 Mode Register 11
		#(OFFSET, MASK, VALUE)      (0XFD0801AC, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD0801AC 0xFFFFFFFF 0x00000000
		# Register : MR12 @ 0XFD0801B0</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR12_RESERVED_31_8                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR12_RSVD                                                           0x0

		# VREF_CA Range Select.
		# PSU_DDR_PHY_MR12_VR_CA                                                          0x1

		# Controls the VREF(ca) levels for Frequency-Set-Point[1:0].
		# PSU_DDR_PHY_MR12_VREF_CA                                                        0xd

		# LPDDR4 Mode Register 12
		#(OFFSET, MASK, VALUE)      (0XFD0801B0, 0xFFFFFFFFU ,0x0000004DU)  */
    mask_write 0XFD0801B0 0xFFFFFFFF 0x0000004D
		# Register : MR13 @ 0XFD0801B4</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR13_RESERVED_31_8                                                  0x0

		# Frequency Set Point Operation Mode
		# PSU_DDR_PHY_MR13_FSPOP                                                          0x0

		# Frequency Set Point Write Enable
		# PSU_DDR_PHY_MR13_FSPWR                                                          0x0

		# Data Mask Enable
		# PSU_DDR_PHY_MR13_DMD                                                            0x0

		# Refresh Rate Option
		# PSU_DDR_PHY_MR13_RRO                                                            0x0

		# VREF Current Generator
		# PSU_DDR_PHY_MR13_VRCG                                                           0x1

		# VREF Output
		# PSU_DDR_PHY_MR13_VRO                                                            0x0

		# Read Preamble Training Mode
		# PSU_DDR_PHY_MR13_RPT                                                            0x0

		# Command Bus Training
		# PSU_DDR_PHY_MR13_CBT                                                            0x0

		# LPDDR4 Mode Register 13
		#(OFFSET, MASK, VALUE)      (0XFD0801B4, 0xFFFFFFFFU ,0x00000008U)  */
    mask_write 0XFD0801B4 0xFFFFFFFF 0x00000008
		# Register : MR14 @ 0XFD0801B8</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR14_RESERVED_31_8                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR14_RSVD                                                           0x0

		# VREFDQ Range Selects.
		# PSU_DDR_PHY_MR14_VR_DQ                                                          0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR14_VREF_DQ                                                        0xd

		# LPDDR4 Mode Register 14
		#(OFFSET, MASK, VALUE)      (0XFD0801B8, 0xFFFFFFFFU ,0x0000004DU)  */
    mask_write 0XFD0801B8 0xFFFFFFFF 0x0000004D
		# Register : MR22 @ 0XFD0801D8</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_MR22_RESERVED_31_8                                                  0x0

		# These are JEDEC reserved bits and are recommended by JEDEC to be program
    # med to 0x0.
		# PSU_DDR_PHY_MR22_RSVD                                                           0x0

		# CA ODT termination disable.
		# PSU_DDR_PHY_MR22_ODTD_CA                                                        0x0

		# ODT CS override.
		# PSU_DDR_PHY_MR22_ODTE_CS                                                        0x0

		# ODT CK override.
		# PSU_DDR_PHY_MR22_ODTE_CK                                                        0x0

		# Controller ODT value for VOH calibration.
		# PSU_DDR_PHY_MR22_CODT                                                           0x0

		# LPDDR4 Mode Register 22
		#(OFFSET, MASK, VALUE)      (0XFD0801D8, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD0801D8 0xFFFFFFFF 0x00000000
		# Register : DTCR0 @ 0XFD080200</p>

		# Refresh During Training
		# PSU_DDR_PHY_DTCR0_RFSHDT                                                        0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR0_RESERVED_27_26                                                0x0

		# Data Training Debug Rank Select
		# PSU_DDR_PHY_DTCR0_DTDRS                                                         0x0

		# Data Training with Early/Extended Gate
		# PSU_DDR_PHY_DTCR0_DTEXG                                                         0x0

		# Data Training Extended Write DQS
		# PSU_DDR_PHY_DTCR0_DTEXD                                                         0x0

		# Data Training Debug Step
		# PSU_DDR_PHY_DTCR0_DTDSTP                                                        0x0

		# Data Training Debug Enable
		# PSU_DDR_PHY_DTCR0_DTDEN                                                         0x0

		# Data Training Debug Byte Select
		# PSU_DDR_PHY_DTCR0_DTDBS                                                         0x0

		# Data Training read DBI deskewing configuration
		# PSU_DDR_PHY_DTCR0_DTRDBITR                                                      0x2

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR0_RESERVED_13                                                   0x0

		# Data Training Write Bit Deskew Data Mask
		# PSU_DDR_PHY_DTCR0_DTWBDDM                                                       0x1

		# Refreshes Issued During Entry to Training
		# PSU_DDR_PHY_DTCR0_RFSHEN                                                        0x1

		# Data Training Compare Data
		# PSU_DDR_PHY_DTCR0_DTCMPD                                                        0x1

		# Data Training Using MPR
		# PSU_DDR_PHY_DTCR0_DTMPR                                                         0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR0_RESERVED_5_4                                                  0x0

		# Data Training Repeat Number
		# PSU_DDR_PHY_DTCR0_DTRPTN                                                        0x7

		# Data Training Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080200, 0xFFFFFFFFU ,0x800091C7U)  */
    mask_write 0XFD080200 0xFFFFFFFF 0x800091C7
		# Register : DTCR1 @ 0XFD080204</p>

		# Rank Enable.
		# PSU_DDR_PHY_DTCR1_RANKEN_RSVD                                                   0x0

		# Rank Enable.
		# PSU_DDR_PHY_DTCR1_RANKEN                                                        0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR1_RESERVED_15_14                                                0x0

		# Data Training Rank
		# PSU_DDR_PHY_DTCR1_DTRANK                                                        0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR1_RESERVED_11                                                   0x0

		# Read Leveling Gate Sampling Difference
		# PSU_DDR_PHY_DTCR1_RDLVLGDIFF                                                    0x2

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR1_RESERVED_7                                                    0x0

		# Read Leveling Gate Shift
		# PSU_DDR_PHY_DTCR1_RDLVLGS                                                       0x3

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DTCR1_RESERVED_3                                                    0x0

		# Read Preamble Training enable
		# PSU_DDR_PHY_DTCR1_RDPRMVL_TRN                                                   0x1

		# Read Leveling Enable
		# PSU_DDR_PHY_DTCR1_RDLVLEN                                                       0x1

		# Basic Gate Training Enable
		# PSU_DDR_PHY_DTCR1_BSTEN                                                         0x0

		# Data Training Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080204, 0xFFFFFFFFU ,0x00010236U)  */
    mask_write 0XFD080204 0xFFFFFFFF 0x00010236
		# Register : CATR0 @ 0XFD080240</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_CATR0_RESERVED_31_21                                                0x0

		# Minimum time (in terms of number of dram clocks) between two consectuve
    # CA calibration command
		# PSU_DDR_PHY_CATR0_CACD                                                          0x14

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_CATR0_RESERVED_15_13                                                0x0

		# Minimum time (in terms of number of dram clocks) PUB should wait before
    # sampling the CA response after Calibration command has been sent to the
    # memory
		# PSU_DDR_PHY_CATR0_CAADR                                                         0x10

		# CA_1 Response Byte Lane 1
		# PSU_DDR_PHY_CATR0_CA1BYTE1                                                      0x5

		# CA_1 Response Byte Lane 0
		# PSU_DDR_PHY_CATR0_CA1BYTE0                                                      0x4

		# CA Training Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080240, 0xFFFFFFFFU ,0x00141054U)  */
    mask_write 0XFD080240 0xFFFFFFFF 0x00141054
		# Register : DQSDR0 @ 0XFD080250</p>

		# Number of delay taps by which the DQS gate LCDL will be updated when DQS
    #  drift is detected
		# PSU_DDR_PHY_DQSDR0_DFTDLY                                                       0x0

		# Drift Impedance Update
		# PSU_DDR_PHY_DQSDR0_DFTZQUP                                                      0x0

		# Drift DDL Update
		# PSU_DDR_PHY_DQSDR0_DFTDDLUP                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DQSDR0_RESERVED_25_22                                               0x0

		# Drift Read Spacing
		# PSU_DDR_PHY_DQSDR0_DFTRDSPC                                                     0x0

		# Drift Back-to-Back Reads
		# PSU_DDR_PHY_DQSDR0_DFTB2BRD                                                     0x8

		# Drift Idle Reads
		# PSU_DDR_PHY_DQSDR0_DFTIDLRD                                                     0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DQSDR0_RESERVED_11_8                                                0x0

		# Gate Pulse Enable
		# PSU_DDR_PHY_DQSDR0_DFTGPULSE                                                    0x0

		# DQS Drift Update Mode
		# PSU_DDR_PHY_DQSDR0_DFTUPMODE                                                    0x0

		# DQS Drift Detection Mode
		# PSU_DDR_PHY_DQSDR0_DFTDTMODE                                                    0x0

		# DQS Drift Detection Enable
		# PSU_DDR_PHY_DQSDR0_DFTDTEN                                                      0x0

		# DQS Drift Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080250, 0xFFFFFFFFU ,0x00088000U)  */
    mask_write 0XFD080250 0xFFFFFFFF 0x00088000
		# Register : BISTLSR @ 0XFD080414</p>

		# LFSR seed for pseudo-random BIST patterns
		# PSU_DDR_PHY_BISTLSR_SEED                                                        0x12341000

		# BIST LFSR Seed Register
		#(OFFSET, MASK, VALUE)      (0XFD080414, 0xFFFFFFFFU ,0x12341000U)  */
    mask_write 0XFD080414 0xFFFFFFFF 0x12341000
		# Register : RIOCR5 @ 0XFD0804F4</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_RIOCR5_RESERVED_31_16                                               0x0

		# Reserved. Return zeros on reads.
		# PSU_DDR_PHY_RIOCR5_ODTOEMODE_RSVD                                               0x0

		# SDRAM On-die Termination Output Enable (OE) Mode Selection.
		# PSU_DDR_PHY_RIOCR5_ODTOEMODE                                                    0x5

		# Rank I/O Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD0804F4, 0xFFFFFFFFU ,0x00000005U)  */
    mask_write 0XFD0804F4 0xFFFFFFFF 0x00000005
		# Register : ACIOCR0 @ 0XFD080500</p>

		# Address/Command Slew Rate (D3F I/O Only)
		# PSU_DDR_PHY_ACIOCR0_ACSR                                                        0x0

		# SDRAM Reset I/O Mode
		# PSU_DDR_PHY_ACIOCR0_RSTIOM                                                      0x1

		# SDRAM Reset Power Down Receiver
		# PSU_DDR_PHY_ACIOCR0_RSTPDR                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACIOCR0_RESERVED_27                                                 0x0

		# SDRAM Reset On-Die Termination
		# PSU_DDR_PHY_ACIOCR0_RSTODT                                                      0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACIOCR0_RESERVED_25_10                                              0x0

		# CK Duty Cycle Correction
		# PSU_DDR_PHY_ACIOCR0_CKDCC                                                       0x0

		# AC Power Down Receiver Mode
		# PSU_DDR_PHY_ACIOCR0_ACPDRMODE                                                   0x2

		# AC On-die Termination Mode
		# PSU_DDR_PHY_ACIOCR0_ACODTMODE                                                   0x2

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACIOCR0_RESERVED_1                                                  0x0

		# Control delayed or non-delayed clock to CS_N/ODT?CKE AC slices.
		# PSU_DDR_PHY_ACIOCR0_ACRANKCLKSEL                                                0x0

		# AC I/O Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080500, 0xFFFFFFFFU ,0x30000028U)  */
    mask_write 0XFD080500 0xFFFFFFFF 0x30000028
		# Register : ACIOCR2 @ 0XFD080508</p>

		# Clock gating for glue logic inside CLKGEN and glue logic inside CONTROL
    # slice
		# PSU_DDR_PHY_ACIOCR2_CLKGENCLKGATE                                               0x0

		# Clock gating for Output Enable D slices [0]
		# PSU_DDR_PHY_ACIOCR2_ACOECLKGATE0                                                0x0

		# Clock gating for Power Down Receiver D slices [0]
		# PSU_DDR_PHY_ACIOCR2_ACPDRCLKGATE0                                               0x0

		# Clock gating for Termination Enable D slices [0]
		# PSU_DDR_PHY_ACIOCR2_ACTECLKGATE0                                                0x0

		# Clock gating for CK# D slices [1:0]
		# PSU_DDR_PHY_ACIOCR2_CKNCLKGATE0                                                 0x2

		# Clock gating for CK D slices [1:0]
		# PSU_DDR_PHY_ACIOCR2_CKCLKGATE0                                                  0x2

		# Clock gating for AC D slices [23:0]
		# PSU_DDR_PHY_ACIOCR2_ACCLKGATE0                                                  0x0

		# AC I/O Configuration Register 2
		#(OFFSET, MASK, VALUE)      (0XFD080508, 0xFFFFFFFFU ,0x0A000000U)  */
    mask_write 0XFD080508 0xFFFFFFFF 0x0A000000
		# Register : ACIOCR3 @ 0XFD08050C</p>

		# SDRAM Parity Output Enable (OE) Mode Selection
		# PSU_DDR_PHY_ACIOCR3_PAROEMODE                                                   0x0

		# SDRAM Bank Group Output Enable (OE) Mode Selection
		# PSU_DDR_PHY_ACIOCR3_BGOEMODE                                                    0x0

		# SDRAM Bank Address Output Enable (OE) Mode Selection
		# PSU_DDR_PHY_ACIOCR3_BAOEMODE                                                    0x0

		# SDRAM A[17] Output Enable (OE) Mode Selection
		# PSU_DDR_PHY_ACIOCR3_A17OEMODE                                                   0x0

		# SDRAM A[16] / RAS_n Output Enable (OE) Mode Selection
		# PSU_DDR_PHY_ACIOCR3_A16OEMODE                                                   0x0

		# SDRAM ACT_n Output Enable (OE) Mode Selection (DDR4 only)
		# PSU_DDR_PHY_ACIOCR3_ACTOEMODE                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACIOCR3_RESERVED_15_8                                               0x0

		# Reserved. Return zeros on reads.
		# PSU_DDR_PHY_ACIOCR3_CKOEMODE_RSVD                                               0x0

		# SDRAM CK Output Enable (OE) Mode Selection.
		# PSU_DDR_PHY_ACIOCR3_CKOEMODE                                                    0x9

		# AC I/O Configuration Register 3
		#(OFFSET, MASK, VALUE)      (0XFD08050C, 0xFFFFFFFFU ,0x00000009U)  */
    mask_write 0XFD08050C 0xFFFFFFFF 0x00000009
		# Register : ACIOCR4 @ 0XFD080510</p>

		# Clock gating for AC LB slices and loopback read valid slices
		# PSU_DDR_PHY_ACIOCR4_LBCLKGATE                                                   0x0

		# Clock gating for Output Enable D slices [1]
		# PSU_DDR_PHY_ACIOCR4_ACOECLKGATE1                                                0x0

		# Clock gating for Power Down Receiver D slices [1]
		# PSU_DDR_PHY_ACIOCR4_ACPDRCLKGATE1                                               0x0

		# Clock gating for Termination Enable D slices [1]
		# PSU_DDR_PHY_ACIOCR4_ACTECLKGATE1                                                0x0

		# Clock gating for CK# D slices [3:2]
		# PSU_DDR_PHY_ACIOCR4_CKNCLKGATE1                                                 0x2

		# Clock gating for CK D slices [3:2]
		# PSU_DDR_PHY_ACIOCR4_CKCLKGATE1                                                  0x2

		# Clock gating for AC D slices [47:24]
		# PSU_DDR_PHY_ACIOCR4_ACCLKGATE1                                                  0x0

		# AC I/O Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080510, 0xFFFFFFFFU ,0x0A000000U)  */
    mask_write 0XFD080510 0xFFFFFFFF 0x0A000000
		# Register : IOVCR0 @ 0XFD080520</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_IOVCR0_RESERVED_31_29                                               0x0

		# Address/command lane VREF Pad Enable
		# PSU_DDR_PHY_IOVCR0_ACREFPEN                                                     0x0

		# Address/command lane Internal VREF Enable
		# PSU_DDR_PHY_IOVCR0_ACREFEEN                                                     0x0

		# Address/command lane Single-End VREF Enable
		# PSU_DDR_PHY_IOVCR0_ACREFSEN                                                     0x1

		# Address/command lane Internal VREF Enable
		# PSU_DDR_PHY_IOVCR0_ACREFIEN                                                     0x1

		# External VREF generato REFSEL range select
		# PSU_DDR_PHY_IOVCR0_ACREFESELRANGE                                               0x0

		# Address/command lane External VREF Select
		# PSU_DDR_PHY_IOVCR0_ACREFESEL                                                    0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_IOVCR0_ACREFSSELRANGE                                               0x1

		# Address/command lane Single-End VREF Select
		# PSU_DDR_PHY_IOVCR0_ACREFSSEL                                                    0x30

		# Internal VREF generator REFSEL ragne select
		# PSU_DDR_PHY_IOVCR0_ACVREFISELRANGE                                              0x1

		# REFSEL Control for internal AC IOs
		# PSU_DDR_PHY_IOVCR0_ACVREFISEL                                                   0x4e

		# IO VREF Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080520, 0xFFFFFFFFU ,0x0300B0CEU)  */
    mask_write 0XFD080520 0xFFFFFFFF 0x0300B0CE
		# Register : VTCR0 @ 0XFD080528</p>

		# Number of ctl_clk required to meet (> 150ns) timing requirements during
    # DRAM DQ VREF training
		# PSU_DDR_PHY_VTCR0_TVREF                                                         0x7

		# DRM DQ VREF training Enable
		# PSU_DDR_PHY_VTCR0_DVEN                                                          0x1

		# Per Device Addressability Enable
		# PSU_DDR_PHY_VTCR0_PDAEN                                                         0x1

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_VTCR0_RESERVED_26                                                   0x0

		# VREF Word Count
		# PSU_DDR_PHY_VTCR0_VWCR                                                          0x4

		# DRAM DQ VREF step size used during DRAM VREF training
		# PSU_DDR_PHY_VTCR0_DVSS                                                          0x0

		# Maximum VREF limit value used during DRAM VREF training
		# PSU_DDR_PHY_VTCR0_DVMAX                                                         0x32

		# Minimum VREF limit value used during DRAM VREF training
		# PSU_DDR_PHY_VTCR0_DVMIN                                                         0x0

		# Initial DRAM DQ VREF value used during DRAM VREF training
		# PSU_DDR_PHY_VTCR0_DVINIT                                                        0x19

		# VREF Training Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080528, 0xFFFFFFFFU ,0xF9032019U)  */
    mask_write 0XFD080528 0xFFFFFFFF 0xF9032019
		# Register : VTCR1 @ 0XFD08052C</p>

		# Host VREF step size used during VREF training. The register value of N i
    # ndicates step size of (N+1)
		# PSU_DDR_PHY_VTCR1_HVSS                                                          0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_VTCR1_RESERVED_27                                                   0x0

		# Maximum VREF limit value used during DRAM VREF training.
		# PSU_DDR_PHY_VTCR1_HVMAX                                                         0x7f

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_VTCR1_RESERVED_19                                                   0x0

		# Minimum VREF limit value used during DRAM VREF training.
		# PSU_DDR_PHY_VTCR1_HVMIN                                                         0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_VTCR1_RESERVED_11                                                   0x0

		# Static Host Vref Rank Value
		# PSU_DDR_PHY_VTCR1_SHRNK                                                         0x0

		# Static Host Vref Rank Enable
		# PSU_DDR_PHY_VTCR1_SHREN                                                         0x1

		# Number of ctl_clk required to meet (> 200ns) VREF Settling timing requir
    # ements during Host IO VREF training
		# PSU_DDR_PHY_VTCR1_TVREFIO                                                       0x7

		# Eye LCDL Offset value for VREF training
		# PSU_DDR_PHY_VTCR1_EOFF                                                          0x0

		# Number of LCDL Eye points for which VREF training is repeated
		# PSU_DDR_PHY_VTCR1_ENUM                                                          0x0

		# HOST (IO) internal VREF training Enable
		# PSU_DDR_PHY_VTCR1_HVEN                                                          0x1

		# Host IO Type Control
		# PSU_DDR_PHY_VTCR1_HVIO                                                          0x1

		# VREF Training Control Register 1
		#(OFFSET, MASK, VALUE)      (0XFD08052C, 0xFFFFFFFFU ,0x07F001E3U)  */
    mask_write 0XFD08052C 0xFFFFFFFF 0x07F001E3
		# Register : ACBDLR1 @ 0XFD080544</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR1_RESERVED_31_30                                              0x0

		# Delay select for the BDL on Parity.
		# PSU_DDR_PHY_ACBDLR1_PARBD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR1_RESERVED_23_22                                              0x0

		# Delay select for the BDL on Address A[16]. In DDR3 mode this pin is conn
    # ected to WE.
		# PSU_DDR_PHY_ACBDLR1_A16BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR1_RESERVED_15_14                                              0x0

		# Delay select for the BDL on Address A[17]. When not in DDR4 modemode thi
    # s pin is connected to CAS.
		# PSU_DDR_PHY_ACBDLR1_A17BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR1_RESERVED_7_6                                                0x0

		# Delay select for the BDL on ACTN.
		# PSU_DDR_PHY_ACBDLR1_ACTBD                                                       0x0

		# AC Bit Delay Line Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080544, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080544 0xFFFFFFFF 0x00000000
		# Register : ACBDLR2 @ 0XFD080548</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR2_RESERVED_31_30                                              0x0

		# Delay select for the BDL on BG[1].
		# PSU_DDR_PHY_ACBDLR2_BG1BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR2_RESERVED_23_22                                              0x0

		# Delay select for the BDL on BG[0].
		# PSU_DDR_PHY_ACBDLR2_BG0BD                                                       0x0

		# Reser.ved Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR2_RESERVED_15_14                                              0x0

		# Delay select for the BDL on BA[1].
		# PSU_DDR_PHY_ACBDLR2_BA1BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR2_RESERVED_7_6                                                0x0

		# Delay select for the BDL on BA[0].
		# PSU_DDR_PHY_ACBDLR2_BA0BD                                                       0x0

		# AC Bit Delay Line Register 2
		#(OFFSET, MASK, VALUE)      (0XFD080548, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080548 0xFFFFFFFF 0x00000000
		# Register : ACBDLR6 @ 0XFD080558</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR6_RESERVED_31_30                                              0x0

		# Delay select for the BDL on Address A[3].
		# PSU_DDR_PHY_ACBDLR6_A03BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR6_RESERVED_23_22                                              0x0

		# Delay select for the BDL on Address A[2].
		# PSU_DDR_PHY_ACBDLR6_A02BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR6_RESERVED_15_14                                              0x0

		# Delay select for the BDL on Address A[1].
		# PSU_DDR_PHY_ACBDLR6_A01BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR6_RESERVED_7_6                                                0x0

		# Delay select for the BDL on Address A[0].
		# PSU_DDR_PHY_ACBDLR6_A00BD                                                       0x0

		# AC Bit Delay Line Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080558, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080558 0xFFFFFFFF 0x00000000
		# Register : ACBDLR7 @ 0XFD08055C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR7_RESERVED_31_30                                              0x0

		# Delay select for the BDL on Address A[7].
		# PSU_DDR_PHY_ACBDLR7_A07BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR7_RESERVED_23_22                                              0x0

		# Delay select for the BDL on Address A[6].
		# PSU_DDR_PHY_ACBDLR7_A06BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR7_RESERVED_15_14                                              0x0

		# Delay select for the BDL on Address A[5].
		# PSU_DDR_PHY_ACBDLR7_A05BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR7_RESERVED_7_6                                                0x0

		# Delay select for the BDL on Address A[4].
		# PSU_DDR_PHY_ACBDLR7_A04BD                                                       0x0

		# AC Bit Delay Line Register 7
		#(OFFSET, MASK, VALUE)      (0XFD08055C, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD08055C 0xFFFFFFFF 0x00000000
		# Register : ACBDLR8 @ 0XFD080560</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR8_RESERVED_31_30                                              0x0

		# Delay select for the BDL on Address A[11].
		# PSU_DDR_PHY_ACBDLR8_A11BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR8_RESERVED_23_22                                              0x0

		# Delay select for the BDL on Address A[10].
		# PSU_DDR_PHY_ACBDLR8_A10BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR8_RESERVED_15_14                                              0x0

		# Delay select for the BDL on Address A[9].
		# PSU_DDR_PHY_ACBDLR8_A09BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR8_RESERVED_7_6                                                0x0

		# Delay select for the BDL on Address A[8].
		# PSU_DDR_PHY_ACBDLR8_A08BD                                                       0x0

		# AC Bit Delay Line Register 8
		#(OFFSET, MASK, VALUE)      (0XFD080560, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080560 0xFFFFFFFF 0x00000000
		# Register : ACBDLR9 @ 0XFD080564</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR9_RESERVED_31_30                                              0x0

		# Delay select for the BDL on Address A[15].
		# PSU_DDR_PHY_ACBDLR9_A15BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR9_RESERVED_23_22                                              0x0

		# Delay select for the BDL on Address A[14].
		# PSU_DDR_PHY_ACBDLR9_A14BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR9_RESERVED_15_14                                              0x0

		# Delay select for the BDL on Address A[13].
		# PSU_DDR_PHY_ACBDLR9_A13BD                                                       0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ACBDLR9_RESERVED_7_6                                                0x0

		# Delay select for the BDL on Address A[12].
		# PSU_DDR_PHY_ACBDLR9_A12BD                                                       0x0

		# AC Bit Delay Line Register 9
		#(OFFSET, MASK, VALUE)      (0XFD080564, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080564 0xFFFFFFFF 0x00000000
		# Register : ZQCR @ 0XFD080680</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_ZQCR_RESERVED_31_26                                                 0x0

		# ZQ VREF Range
		# PSU_DDR_PHY_ZQCR_ZQREFISELRANGE                                                 0x0

		# Programmable Wait for Frequency B
		# PSU_DDR_PHY_ZQCR_PGWAIT_FRQB                                                    0x11

		# Programmable Wait for Frequency A
		# PSU_DDR_PHY_ZQCR_PGWAIT_FRQA                                                    0x15

		# ZQ VREF Pad Enable
		# PSU_DDR_PHY_ZQCR_ZQREFPEN                                                       0x0

		# ZQ Internal VREF Enable
		# PSU_DDR_PHY_ZQCR_ZQREFIEN                                                       0x1

		# Choice of termination mode
		# PSU_DDR_PHY_ZQCR_ODT_MODE                                                       0x1

		# Force ZCAL VT update
		# PSU_DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE                                           0x0

		# IO VT Drift Limit
		# PSU_DDR_PHY_ZQCR_IODLMT                                                         0x2

		# Averaging algorithm enable, if set, enables averaging algorithm
		# PSU_DDR_PHY_ZQCR_AVGEN                                                          0x1

		# Maximum number of averaging rounds to be used by averaging algorithm
		# PSU_DDR_PHY_ZQCR_AVGMAX                                                         0x2

		# ZQ Calibration Type
		# PSU_DDR_PHY_ZQCR_ZCALT                                                          0x0

		# ZQ Power Down
		# PSU_DDR_PHY_ZQCR_ZQPD                                                           0x0

		# ZQ Impedance Control Register
		#(OFFSET, MASK, VALUE)      (0XFD080680, 0xFFFFFFFFU ,0x008AAA58U)  */
    mask_write 0XFD080680 0xFFFFFFFF 0x008AAA58
		# Register : ZQ0PR0 @ 0XFD080684</p>

		# Pull-down drive strength ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ0PR0_PD_DRV_ZDEN                                                  0x0

		# Pull-up drive strength ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ0PR0_PU_DRV_ZDEN                                                  0x0

		# Pull-down termination ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ0PR0_PD_ODT_ZDEN                                                  0x0

		# Pull-up termination ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ0PR0_PU_ODT_ZDEN                                                  0x0

		# Calibration segment bypass
		# PSU_DDR_PHY_ZQ0PR0_ZSEGBYP                                                      0x0

		# VREF latch mode controls the mode in which the ZLE pin of the PVREF cell
    #  is driven by the PUB
		# PSU_DDR_PHY_ZQ0PR0_ZLE_MODE                                                     0x0

		# Termination adjustment
		# PSU_DDR_PHY_ZQ0PR0_ODT_ADJUST                                                   0x0

		# Pulldown drive strength adjustment
		# PSU_DDR_PHY_ZQ0PR0_PD_DRV_ADJUST                                                0x0

		# Pullup drive strength adjustment
		# PSU_DDR_PHY_ZQ0PR0_PU_DRV_ADJUST                                                0x0

		# DRAM Impedance Divide Ratio
		# PSU_DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT                                               0x7

		# HOST Impedance Divide Ratio
		# PSU_DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT                                               0x9

		# Impedance Divide Ratio (pulldown drive calibration during asymmetric dri
    # ve strength calibration)
		# PSU_DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD                                            0xd

		# Impedance Divide Ratio (pullup drive calibration during asymmetric drive
    #  strength calibration)
		# PSU_DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU                                            0xd

		# ZQ n Impedance Control Program Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080684, 0xFFFFFFFFU ,0x000079DDU)  */
    mask_write 0XFD080684 0xFFFFFFFF 0x000079DD
		# Register : ZQ0OR0 @ 0XFD080694</p>

		# Reserved. Return zeros on reads.
		# PSU_DDR_PHY_ZQ0OR0_RESERVED_31_26                                               0x0

		# Override value for the pull-up output impedance
		# PSU_DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD                                            0x1e1

		# Reserved. Return zeros on reads.
		# PSU_DDR_PHY_ZQ0OR0_RESERVED_15_10                                               0x0

		# Override value for the pull-down output impedance
		# PSU_DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD                                            0x210

		# ZQ n Impedance Control Override Data Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080694, 0xFFFFFFFFU ,0x01E10210U)  */
    mask_write 0XFD080694 0xFFFFFFFF 0x01E10210
		# Register : ZQ0OR1 @ 0XFD080698</p>

		# Reserved. Return zeros on reads.
		# PSU_DDR_PHY_ZQ0OR1_RESERVED_31_26                                               0x0

		# Override value for the pull-up termination
		# PSU_DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD                                            0x1e1

		# Reserved. Return zeros on reads.
		# PSU_DDR_PHY_ZQ0OR1_RESERVED_15_10                                               0x0

		# Override value for the pull-down termination
		# PSU_DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD                                            0x0

		# ZQ n Impedance Control Override Data Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080698, 0xFFFFFFFFU ,0x01E10000U)  */
    mask_write 0XFD080698 0xFFFFFFFF 0x01E10000
		# Register : ZQ1PR0 @ 0XFD0806A4</p>

		# Pull-down drive strength ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ1PR0_PD_DRV_ZDEN                                                  0x0

		# Pull-up drive strength ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ1PR0_PU_DRV_ZDEN                                                  0x0

		# Pull-down termination ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ1PR0_PD_ODT_ZDEN                                                  0x0

		# Pull-up termination ZCTRL over-ride enable
		# PSU_DDR_PHY_ZQ1PR0_PU_ODT_ZDEN                                                  0x0

		# Calibration segment bypass
		# PSU_DDR_PHY_ZQ1PR0_ZSEGBYP                                                      0x0

		# VREF latch mode controls the mode in which the ZLE pin of the PVREF cell
    #  is driven by the PUB
		# PSU_DDR_PHY_ZQ1PR0_ZLE_MODE                                                     0x0

		# Termination adjustment
		# PSU_DDR_PHY_ZQ1PR0_ODT_ADJUST                                                   0x0

		# Pulldown drive strength adjustment
		# PSU_DDR_PHY_ZQ1PR0_PD_DRV_ADJUST                                                0x1

		# Pullup drive strength adjustment
		# PSU_DDR_PHY_ZQ1PR0_PU_DRV_ADJUST                                                0x0

		# DRAM Impedance Divide Ratio
		# PSU_DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT                                               0x7

		# HOST Impedance Divide Ratio
		# PSU_DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT                                               0xb

		# Impedance Divide Ratio (pulldown drive calibration during asymmetric dri
    # ve strength calibration)
		# PSU_DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD                                            0xd

		# Impedance Divide Ratio (pullup drive calibration during asymmetric drive
    #  strength calibration)
		# PSU_DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU                                            0xb

		# ZQ n Impedance Control Program Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0806A4, 0xFFFFFFFFU ,0x00087BDBU)  */
    mask_write 0XFD0806A4 0xFFFFFFFF 0x00087BDB
		# Register : DX0GCR0 @ 0XFD080700</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX0GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX0GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX0GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX0GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX0GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX0GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX0GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX0GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX0GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX0GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX0GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX0GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX0GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX0GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX0GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX0GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX0GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080700, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080700 0xFFFFFFFF 0x40800604
		# Register : DX0GCR4 @ 0XFD080710</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX0GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX0GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX0GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX0GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX0GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX0GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX0GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX0GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX0GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX0GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080710, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080710 0xFFFFFFFF 0x0E00B03C
		# Register : DX0GCR5 @ 0XFD080714</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX0GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX0GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX0GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX0GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080714, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080714 0xFFFFFFFF 0x09095555
		# Register : DX0GCR6 @ 0XFD080718</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX0GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX0GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX0GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX0GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX0GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080718, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080718 0xFFFFFFFF 0x09092B2B
		# Register : DX1GCR0 @ 0XFD080800</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX1GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX1GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX1GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX1GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX1GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX1GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX1GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX1GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX1GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX1GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX1GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX1GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX1GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX1GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX1GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX1GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX1GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080800, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080800 0xFFFFFFFF 0x40800604
		# Register : DX1GCR4 @ 0XFD080810</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX1GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX1GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX1GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX1GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX1GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX1GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX1GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX1GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX1GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX1GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080810, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080810 0xFFFFFFFF 0x0E00B03C
		# Register : DX1GCR5 @ 0XFD080814</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX1GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX1GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX1GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX1GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080814, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080814 0xFFFFFFFF 0x09095555
		# Register : DX1GCR6 @ 0XFD080818</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX1GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX1GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX1GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX1GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX1GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080818, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080818 0xFFFFFFFF 0x09092B2B
		# Register : DX2GCR0 @ 0XFD080900</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX2GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX2GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX2GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX2GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX2GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX2GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX2GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX2GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX2GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX2GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX2GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX2GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX2GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX2GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX2GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX2GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX2GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080900, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080900 0xFFFFFFFF 0x40800604
		# Register : DX2GCR1 @ 0XFD080904</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX2GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX2GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX2GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX2GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX2GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX2GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX2GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX2GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX2GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX2GCR1_DQEN                                                        0xff

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080904, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080904 0xFFFFFFFF 0x00007FFF
		# Register : DX2GCR4 @ 0XFD080910</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX2GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX2GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX2GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX2GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX2GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX2GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX2GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX2GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX2GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX2GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080910, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080910 0xFFFFFFFF 0x0E00B03C
		# Register : DX2GCR5 @ 0XFD080914</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX2GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX2GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX2GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX2GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080914, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080914 0xFFFFFFFF 0x09095555
		# Register : DX2GCR6 @ 0XFD080918</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX2GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX2GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX2GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX2GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX2GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080918, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080918 0xFFFFFFFF 0x09092B2B
		# Register : DX3GCR0 @ 0XFD080A00</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX3GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX3GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX3GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX3GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX3GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX3GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX3GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX3GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX3GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX3GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX3GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX3GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX3GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX3GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX3GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX3GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX3GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080A00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080A00 0xFFFFFFFF 0x40800604
		# Register : DX3GCR1 @ 0XFD080A04</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX3GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX3GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX3GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX3GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX3GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX3GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX3GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX3GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX3GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX3GCR1_DQEN                                                        0xff

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080A04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080A04 0xFFFFFFFF 0x00007FFF
		# Register : DX3GCR4 @ 0XFD080A10</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX3GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX3GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX3GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX3GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX3GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX3GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX3GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX3GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX3GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX3GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080A10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080A10 0xFFFFFFFF 0x0E00B03C
		# Register : DX3GCR5 @ 0XFD080A14</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX3GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX3GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX3GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX3GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080A14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080A14 0xFFFFFFFF 0x09095555
		# Register : DX3GCR6 @ 0XFD080A18</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX3GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX3GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX3GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX3GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX3GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080A18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080A18 0xFFFFFFFF 0x09092B2B
		# Register : DX4GCR0 @ 0XFD080B00</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX4GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX4GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX4GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX4GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX4GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX4GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX4GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX4GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX4GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX4GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX4GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX4GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX4GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX4GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX4GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX4GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX4GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080B00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080B00 0xFFFFFFFF 0x40800604
		# Register : DX4GCR1 @ 0XFD080B04</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX4GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX4GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX4GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX4GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX4GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX4GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX4GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX4GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX4GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX4GCR1_DQEN                                                        0xff

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080B04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080B04 0xFFFFFFFF 0x00007FFF
		# Register : DX4GCR4 @ 0XFD080B10</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX4GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX4GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX4GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX4GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX4GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX4GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX4GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX4GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX4GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX4GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080B10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080B10 0xFFFFFFFF 0x0E00B03C
		# Register : DX4GCR5 @ 0XFD080B14</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX4GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX4GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX4GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX4GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080B14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080B14 0xFFFFFFFF 0x09095555
		# Register : DX4GCR6 @ 0XFD080B18</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX4GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX4GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX4GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX4GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX4GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080B18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080B18 0xFFFFFFFF 0x09092B2B
		# Register : DX5GCR0 @ 0XFD080C00</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX5GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX5GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX5GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX5GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX5GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX5GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX5GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX5GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX5GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX5GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX5GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX5GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX5GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX5GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX5GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX5GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX5GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080C00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080C00 0xFFFFFFFF 0x40800604
		# Register : DX5GCR1 @ 0XFD080C04</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX5GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX5GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX5GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX5GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX5GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX5GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX5GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX5GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX5GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX5GCR1_DQEN                                                        0xff

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080C04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080C04 0xFFFFFFFF 0x00007FFF
		# Register : DX5GCR4 @ 0XFD080C10</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX5GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX5GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX5GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX5GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX5GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX5GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX5GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX5GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX5GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX5GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080C10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080C10 0xFFFFFFFF 0x0E00B03C
		# Register : DX5GCR5 @ 0XFD080C14</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX5GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX5GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX5GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX5GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080C14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080C14 0xFFFFFFFF 0x09095555
		# Register : DX5GCR6 @ 0XFD080C18</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX5GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX5GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX5GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX5GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX5GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080C18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080C18 0xFFFFFFFF 0x09092B2B
		# Register : DX6GCR0 @ 0XFD080D00</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX6GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX6GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX6GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX6GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX6GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX6GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX6GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX6GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX6GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX6GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX6GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX6GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX6GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX6GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX6GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX6GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX6GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080D00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080D00 0xFFFFFFFF 0x40800604
		# Register : DX6GCR1 @ 0XFD080D04</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX6GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX6GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX6GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX6GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX6GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX6GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX6GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX6GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX6GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX6GCR1_DQEN                                                        0xff

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080D04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080D04 0xFFFFFFFF 0x00007FFF
		# Register : DX6GCR4 @ 0XFD080D10</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX6GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX6GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX6GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX6GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX6GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX6GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX6GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX6GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX6GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX6GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080D10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080D10 0xFFFFFFFF 0x0E00B03C
		# Register : DX6GCR5 @ 0XFD080D14</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX6GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX6GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX6GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX6GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080D14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080D14 0xFFFFFFFF 0x09095555
		# Register : DX6GCR6 @ 0XFD080D18</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX6GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX6GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX6GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX6GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX6GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080D18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080D18 0xFFFFFFFF 0x09092B2B
		# Register : DX7GCR0 @ 0XFD080E00</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX7GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX7GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX7GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX7GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX7GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX7GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX7GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX7GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX7GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX7GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX7GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX7GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX7GCR0_DQSGPDR                                                     0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX7GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX7GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX7GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX7GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080E00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080E00 0xFFFFFFFF 0x40800604
		# Register : DX7GCR1 @ 0XFD080E04</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX7GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX7GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX7GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX7GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX7GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX7GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX7GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX7GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX7GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX7GCR1_DQEN                                                        0xff

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080E04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080E04 0xFFFFFFFF 0x00007FFF
		# Register : DX7GCR4 @ 0XFD080E10</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX7GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX7GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX7GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX7GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX7GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX7GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX7GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX7GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX7GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX7GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080E10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080E10 0xFFFFFFFF 0x0E00B03C
		# Register : DX7GCR5 @ 0XFD080E14</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX7GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX7GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX7GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX7GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080E14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080E14 0xFFFFFFFF 0x09095555
		# Register : DX7GCR6 @ 0XFD080E18</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX7GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX7GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX7GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX7GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX7GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080E18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080E18 0xFFFFFFFF 0x09092B2B
		# Register : DX8GCR0 @ 0XFD080F00</p>

		# Calibration Bypass
		# PSU_DDR_PHY_DX8GCR0_CALBYP                                                      0x0

		# Master Delay Line Enable
		# PSU_DDR_PHY_DX8GCR0_MDLEN                                                       0x1

		# Configurable ODT(TE) Phase Shift
		# PSU_DDR_PHY_DX8GCR0_CODTSHFT                                                    0x0

		# DQS Duty Cycle Correction
		# PSU_DDR_PHY_DX8GCR0_DQSDCC                                                      0x0

		# Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd
    #  input for the respective bypte lane of the PHY
		# PSU_DDR_PHY_DX8GCR0_RDDLY                                                       0x8

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8GCR0_RESERVED_19_14                                              0x0

		# DQSNSE Power Down Receiver
		# PSU_DDR_PHY_DX8GCR0_DQSNSEPDR                                                   0x0

		# DQSSE Power Down Receiver
		# PSU_DDR_PHY_DX8GCR0_DQSSEPDR                                                    0x0

		# RTT On Additive Latency
		# PSU_DDR_PHY_DX8GCR0_RTTOAL                                                      0x0

		# RTT Output Hold
		# PSU_DDR_PHY_DX8GCR0_RTTOH                                                       0x3

		# Configurable PDR Phase Shift
		# PSU_DDR_PHY_DX8GCR0_CPDRSHFT                                                    0x0

		# DQSR Power Down
		# PSU_DDR_PHY_DX8GCR0_DQSRPD                                                      0x0

		# DQSG Power Down Receiver
		# PSU_DDR_PHY_DX8GCR0_DQSGPDR                                                     0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8GCR0_RESERVED_4                                                  0x0

		# DQSG On-Die Termination
		# PSU_DDR_PHY_DX8GCR0_DQSGODT                                                     0x0

		# DQSG Output Enable
		# PSU_DDR_PHY_DX8GCR0_DQSGOE                                                      0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8GCR0_RESERVED_1_0                                                0x0

		# DATX8 n General Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD080F00, 0xFFFFFFFFU ,0x40800624U)  */
    mask_write 0XFD080F00 0xFFFFFFFF 0x40800624
		# Register : DX8GCR1 @ 0XFD080F04</p>

		# Enables the PDR mode for DQ[7:0]
		# PSU_DDR_PHY_DX8GCR1_DXPDRMODE                                                   0x0

		# Reserved. Returns zeroes on reads.
		# PSU_DDR_PHY_DX8GCR1_RESERVED_15                                                 0x0

		# Select the delayed or non-delayed read data strobe #
		# PSU_DDR_PHY_DX8GCR1_QSNSEL                                                      0x1

		# Select the delayed or non-delayed read data strobe
		# PSU_DDR_PHY_DX8GCR1_QSSEL                                                       0x1

		# Enables Read Data Strobe in a byte lane
		# PSU_DDR_PHY_DX8GCR1_OEEN                                                        0x1

		# Enables PDR in a byte lane
		# PSU_DDR_PHY_DX8GCR1_PDREN                                                       0x1

		# Enables ODT/TE in a byte lane
		# PSU_DDR_PHY_DX8GCR1_TEEN                                                        0x1

		# Enables Write Data strobe in a byte lane
		# PSU_DDR_PHY_DX8GCR1_DSEN                                                        0x1

		# Enables DM pin in a byte lane
		# PSU_DDR_PHY_DX8GCR1_DMEN                                                        0x1

		# Enables DQ corresponding to each bit in a byte
		# PSU_DDR_PHY_DX8GCR1_DQEN                                                        0x0

		# DATX8 n General Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD080F04, 0xFFFFFFFFU ,0x00007F00U)  */
    mask_write 0XFD080F04 0xFFFFFFFF 0x00007F00
		# Register : DX8GCR4 @ 0XFD080F10</p>

		# Byte lane VREF IOM (Used only by D4MU IOs)
		# PSU_DDR_PHY_DX8GCR4_RESERVED_31_29                                              0x0

		# Byte Lane VREF Pad Enable
		# PSU_DDR_PHY_DX8GCR4_DXREFPEN                                                    0x0

		# Byte Lane Internal VREF Enable
		# PSU_DDR_PHY_DX8GCR4_DXREFEEN                                                    0x3

		# Byte Lane Single-End VREF Enable
		# PSU_DDR_PHY_DX8GCR4_DXREFSEN                                                    0x1

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR4_RESERVED_24                                                 0x0

		# External VREF generator REFSEL range select
		# PSU_DDR_PHY_DX8GCR4_DXREFESELRANGE                                              0x0

		# Byte Lane External VREF Select
		# PSU_DDR_PHY_DX8GCR4_DXREFESEL                                                   0x0

		# Single ended VREF generator REFSEL range select
		# PSU_DDR_PHY_DX8GCR4_DXREFSSELRANGE                                              0x1

		# Byte Lane Single-End VREF Select
		# PSU_DDR_PHY_DX8GCR4_DXREFSSEL                                                   0x30

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR4_RESERVED_7_6                                                0x0

		# VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX8GCR4_DXREFIEN                                                    0xf

		# VRMON control for DQ IO (Single Ended) buffers of a byte lane.
		# PSU_DDR_PHY_DX8GCR4_DXREFIMON                                                   0x0

		# DATX8 n General Configuration Register 4
		#(OFFSET, MASK, VALUE)      (0XFD080F10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080F10 0xFFFFFFFF 0x0E00B03C
		# Register : DX8GCR5 @ 0XFD080F14</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR5_RESERVED_31                                                 0x0

		# Byte Lane internal VREF Select for Rank 3
		# PSU_DDR_PHY_DX8GCR5_DXREFISELR3                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR5_RESERVED_23                                                 0x0

		# Byte Lane internal VREF Select for Rank 2
		# PSU_DDR_PHY_DX8GCR5_DXREFISELR2                                                 0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR5_RESERVED_15                                                 0x0

		# Byte Lane internal VREF Select for Rank 1
		# PSU_DDR_PHY_DX8GCR5_DXREFISELR1                                                 0x55

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR5_RESERVED_7                                                  0x0

		# Byte Lane internal VREF Select for Rank 0
		# PSU_DDR_PHY_DX8GCR5_DXREFISELR0                                                 0x55

		# DATX8 n General Configuration Register 5
		#(OFFSET, MASK, VALUE)      (0XFD080F14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080F14 0xFFFFFFFF 0x09095555
		# Register : DX8GCR6 @ 0XFD080F18</p>

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR6_RESERVED_31_30                                              0x0

		# DRAM DQ VREF Select for Rank3
		# PSU_DDR_PHY_DX8GCR6_DXDQVREFR3                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR6_RESERVED_23_22                                              0x0

		# DRAM DQ VREF Select for Rank2
		# PSU_DDR_PHY_DX8GCR6_DXDQVREFR2                                                  0x9

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR6_RESERVED_15_14                                              0x0

		# DRAM DQ VREF Select for Rank1
		# PSU_DDR_PHY_DX8GCR6_DXDQVREFR1                                                  0x2b

		# Reserved. Returns zeros on reads.
		# PSU_DDR_PHY_DX8GCR6_RESERVED_7_6                                                0x0

		# DRAM DQ VREF Select for Rank0
		# PSU_DDR_PHY_DX8GCR6_DXDQVREFR0                                                  0x2b

		# DATX8 n General Configuration Register 6
		#(OFFSET, MASK, VALUE)      (0XFD080F18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080F18 0xFFFFFFFF 0x09092B2B
		# Register : DX8SL0OSC @ 0XFD081400</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0OSC_RESERVED_31_30                                            0x0

		# Enable Clock Gating for DX ddr_clk
		# PSU_DDR_PHY_DX8SL0OSC_GATEDXRDCLK                                               0x2

		# Enable Clock Gating for DX ctl_rd_clk
		# PSU_DDR_PHY_DX8SL0OSC_GATEDXDDRCLK                                              0x2

		# Enable Clock Gating for DX ctl_clk
		# PSU_DDR_PHY_DX8SL0OSC_GATEDXCTLCLK                                              0x2

		# Selects the level to which clocks will be stalled when clock gating is e
    # nabled.
		# PSU_DDR_PHY_DX8SL0OSC_CLKLEVEL                                                  0x0

		# Loopback Mode
		# PSU_DDR_PHY_DX8SL0OSC_LBMODE                                                    0x0

		# Load GSDQS LCDL with 2x the calibrated GSDQSPRD value
		# PSU_DDR_PHY_DX8SL0OSC_LBGSDQS                                                   0x0

		# Loopback DQS Gating
		# PSU_DDR_PHY_DX8SL0OSC_LBGDQS                                                    0x0

		# Loopback DQS Shift
		# PSU_DDR_PHY_DX8SL0OSC_LBDQSS                                                    0x0

		# PHY High-Speed Reset
		# PSU_DDR_PHY_DX8SL0OSC_PHYHRST                                                   0x1

		# PHY FIFO Reset
		# PSU_DDR_PHY_DX8SL0OSC_PHYFRST                                                   0x1

		# Delay Line Test Start
		# PSU_DDR_PHY_DX8SL0OSC_DLTST                                                     0x0

		# Delay Line Test Mode
		# PSU_DDR_PHY_DX8SL0OSC_DLTMODE                                                   0x0

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL0OSC_RESERVED_12_11                                            0x3

		# Oscillator Mode Write-Data Delay Line Select
		# PSU_DDR_PHY_DX8SL0OSC_OSCWDDL                                                   0x3

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL0OSC_RESERVED_8_7                                              0x3

		# Oscillator Mode Write-Leveling Delay Line Select
		# PSU_DDR_PHY_DX8SL0OSC_OSCWDL                                                    0x3

		# Oscillator Mode Division
		# PSU_DDR_PHY_DX8SL0OSC_OSCDIV                                                    0xf

		# Oscillator Enable
		# PSU_DDR_PHY_DX8SL0OSC_OSCEN                                                     0x0

		# DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Lo
    # opback, and Gated Clock Control Register
		#(OFFSET, MASK, VALUE)      (0XFD081400, 0xFFFFFFFFU ,0x2A019FFEU)  */
    mask_write 0XFD081400 0xFFFFFFFF 0x2A019FFE
		# Register : DX8SL0PLLCR0 @ 0XFD081404</p>

		# PLL Bypass
		# PSU_DDR_PHY_DX8SL0PLLCR0_PLLBYP                                                 0x0

		# PLL Reset
		# PSU_DDR_PHY_DX8SL0PLLCR0_PLLRST                                                 0x0

		# PLL Power Down
		# PSU_DDR_PHY_DX8SL0PLLCR0_PLLPD                                                  0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_DX8SL0PLLCR0_RSTOPM                                                 0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_DX8SL0PLLCR0_FRQSEL                                                 0x1

		# Relock Mode
		# PSU_DDR_PHY_DX8SL0PLLCR0_RLOCKM                                                 0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_DX8SL0PLLCR0_CPPC                                                   0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_DX8SL0PLLCR0_CPIC                                                   0x0

		# Gear Shift
		# PSU_DDR_PHY_DX8SL0PLLCR0_GSHIFT                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0PLLCR0_RESERVED_11_9                                          0x0

		# Analog Test Enable (ATOEN)
		# PSU_DDR_PHY_DX8SL0PLLCR0_ATOEN                                                  0x0

		# Analog Test Control
		# PSU_DDR_PHY_DX8SL0PLLCR0_ATC                                                    0x0

		# Digital Test Control
		# PSU_DDR_PHY_DX8SL0PLLCR0_DTC                                                    0x0

		# DAXT8 0-1 PLL Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD081404, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD081404 0xFFFFFFFF 0x01100000
		# Register : DX8SL0DQSCTL @ 0XFD08141C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25                                         0x0

		# Read Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL0DQSCTL_RRRMODE                                                0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22                                         0x0

		# Write Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL0DQSCTL_WRRMODE                                                0x1

		# DQS Gate Extension
		# PSU_DDR_PHY_DX8SL0DQSCTL_DQSGX                                                  0x0

		# Low Power PLL Power Down
		# PSU_DDR_PHY_DX8SL0DQSCTL_LPPLLPD                                                0x1

		# Low Power I/O Power Down
		# PSU_DDR_PHY_DX8SL0DQSCTL_LPIOPD                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15                                         0x0

		# QS Counter Enable
		# PSU_DDR_PHY_DX8SL0DQSCTL_QSCNTEN                                                0x1

		# Unused DQ I/O Mode
		# PSU_DDR_PHY_DX8SL0DQSCTL_UDQIOM                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10                                         0x0

		# Data Slew Rate
		# PSU_DDR_PHY_DX8SL0DQSCTL_DXSR                                                   0x3

		# DQS_N Resistor
		# PSU_DDR_PHY_DX8SL0DQSCTL_DQSNRES                                                0x0

		# DQS Resistor
		# PSU_DDR_PHY_DX8SL0DQSCTL_DQSRES                                                 0x0

		# DATX8 0-1 DQS Control Register
		#(OFFSET, MASK, VALUE)      (0XFD08141C, 0xFFFFFFFFU ,0x01264300U)  */
    mask_write 0XFD08141C 0xFFFFFFFF 0x01264300
		# Register : DX8SL0DXCTL2 @ 0XFD08142C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24                                         0x0

		# Configurable Read Data Enable
		# PSU_DDR_PHY_DX8SL0DXCTL2_CRDEN                                                  0x0

		# OX Extension during Post-amble
		# PSU_DDR_PHY_DX8SL0DXCTL2_POSOEX                                                 0x0

		# OE Extension during Pre-amble
		# PSU_DDR_PHY_DX8SL0DXCTL2_PREOEX                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_17                                            0x0

		# I/O Assisted Gate Select
		# PSU_DDR_PHY_DX8SL0DXCTL2_IOAG                                                   0x0

		# I/O Loopback Select
		# PSU_DDR_PHY_DX8SL0DXCTL2_IOLB                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13                                         0x0

		# Low Power Wakeup Threshold
		# PSU_DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH                                         0xc

		# Read Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL0DXCTL2_RDBI                                                   0x0

		# Write Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL0DXCTL2_WDBI                                                   0x0

		# PUB Read FIFO Bypass
		# PSU_DDR_PHY_DX8SL0DXCTL2_PRFBYP                                                 0x0

		# DATX8 Receive FIFO Read Mode
		# PSU_DDR_PHY_DX8SL0DXCTL2_RDMODE                                                 0x0

		# Disables the Read FIFO Reset
		# PSU_DDR_PHY_DX8SL0DXCTL2_DISRST                                                 0x0

		# Read DQS Gate I/O Loopback
		# PSU_DDR_PHY_DX8SL0DXCTL2_DQSGLB                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_0                                             0x0

		# DATX8 0-1 DX Control Register 2
		#(OFFSET, MASK, VALUE)      (0XFD08142C, 0xFFFFFFFFU ,0x00041800U)  */
    mask_write 0XFD08142C 0xFFFFFFFF 0x00041800
		# Register : DX8SL0IOCR @ 0XFD081430</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL0IOCR_RESERVED_31                                              0x0

		# PVREF_DAC REFSEL range select
		# PSU_DDR_PHY_DX8SL0IOCR_DXDACRANGE                                               0x7

		# IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
		# PSU_DDR_PHY_DX8SL0IOCR_DXVREFIOM                                                0x0

		# DX IO Mode
		# PSU_DDR_PHY_DX8SL0IOCR_DXIOM                                                    0x2

		# DX IO Transmitter Mode
		# PSU_DDR_PHY_DX8SL0IOCR_DXTXM                                                    0x0

		# DX IO Receiver Mode
		# PSU_DDR_PHY_DX8SL0IOCR_DXRXM                                                    0x0

		# DATX8 0-1 I/O Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD081430, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD081430 0xFFFFFFFF 0x70800000
		# Register : DX8SL1OSC @ 0XFD081440</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1OSC_RESERVED_31_30                                            0x0

		# Enable Clock Gating for DX ddr_clk
		# PSU_DDR_PHY_DX8SL1OSC_GATEDXRDCLK                                               0x2

		# Enable Clock Gating for DX ctl_rd_clk
		# PSU_DDR_PHY_DX8SL1OSC_GATEDXDDRCLK                                              0x2

		# Enable Clock Gating for DX ctl_clk
		# PSU_DDR_PHY_DX8SL1OSC_GATEDXCTLCLK                                              0x2

		# Selects the level to which clocks will be stalled when clock gating is e
    # nabled.
		# PSU_DDR_PHY_DX8SL1OSC_CLKLEVEL                                                  0x0

		# Loopback Mode
		# PSU_DDR_PHY_DX8SL1OSC_LBMODE                                                    0x0

		# Load GSDQS LCDL with 2x the calibrated GSDQSPRD value
		# PSU_DDR_PHY_DX8SL1OSC_LBGSDQS                                                   0x0

		# Loopback DQS Gating
		# PSU_DDR_PHY_DX8SL1OSC_LBGDQS                                                    0x0

		# Loopback DQS Shift
		# PSU_DDR_PHY_DX8SL1OSC_LBDQSS                                                    0x0

		# PHY High-Speed Reset
		# PSU_DDR_PHY_DX8SL1OSC_PHYHRST                                                   0x1

		# PHY FIFO Reset
		# PSU_DDR_PHY_DX8SL1OSC_PHYFRST                                                   0x1

		# Delay Line Test Start
		# PSU_DDR_PHY_DX8SL1OSC_DLTST                                                     0x0

		# Delay Line Test Mode
		# PSU_DDR_PHY_DX8SL1OSC_DLTMODE                                                   0x0

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL1OSC_RESERVED_12_11                                            0x3

		# Oscillator Mode Write-Data Delay Line Select
		# PSU_DDR_PHY_DX8SL1OSC_OSCWDDL                                                   0x3

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL1OSC_RESERVED_8_7                                              0x3

		# Oscillator Mode Write-Leveling Delay Line Select
		# PSU_DDR_PHY_DX8SL1OSC_OSCWDL                                                    0x3

		# Oscillator Mode Division
		# PSU_DDR_PHY_DX8SL1OSC_OSCDIV                                                    0xf

		# Oscillator Enable
		# PSU_DDR_PHY_DX8SL1OSC_OSCEN                                                     0x0

		# DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Lo
    # opback, and Gated Clock Control Register
		#(OFFSET, MASK, VALUE)      (0XFD081440, 0xFFFFFFFFU ,0x2A019FFEU)  */
    mask_write 0XFD081440 0xFFFFFFFF 0x2A019FFE
		# Register : DX8SL1PLLCR0 @ 0XFD081444</p>

		# PLL Bypass
		# PSU_DDR_PHY_DX8SL1PLLCR0_PLLBYP                                                 0x0

		# PLL Reset
		# PSU_DDR_PHY_DX8SL1PLLCR0_PLLRST                                                 0x0

		# PLL Power Down
		# PSU_DDR_PHY_DX8SL1PLLCR0_PLLPD                                                  0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_DX8SL1PLLCR0_RSTOPM                                                 0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_DX8SL1PLLCR0_FRQSEL                                                 0x1

		# Relock Mode
		# PSU_DDR_PHY_DX8SL1PLLCR0_RLOCKM                                                 0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_DX8SL1PLLCR0_CPPC                                                   0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_DX8SL1PLLCR0_CPIC                                                   0x0

		# Gear Shift
		# PSU_DDR_PHY_DX8SL1PLLCR0_GSHIFT                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1PLLCR0_RESERVED_11_9                                          0x0

		# Analog Test Enable (ATOEN)
		# PSU_DDR_PHY_DX8SL1PLLCR0_ATOEN                                                  0x0

		# Analog Test Control
		# PSU_DDR_PHY_DX8SL1PLLCR0_ATC                                                    0x0

		# Digital Test Control
		# PSU_DDR_PHY_DX8SL1PLLCR0_DTC                                                    0x0

		# DAXT8 0-1 PLL Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD081444, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD081444 0xFFFFFFFF 0x01100000
		# Register : DX8SL1DQSCTL @ 0XFD08145C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25                                         0x0

		# Read Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL1DQSCTL_RRRMODE                                                0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22                                         0x0

		# Write Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL1DQSCTL_WRRMODE                                                0x1

		# DQS Gate Extension
		# PSU_DDR_PHY_DX8SL1DQSCTL_DQSGX                                                  0x0

		# Low Power PLL Power Down
		# PSU_DDR_PHY_DX8SL1DQSCTL_LPPLLPD                                                0x1

		# Low Power I/O Power Down
		# PSU_DDR_PHY_DX8SL1DQSCTL_LPIOPD                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15                                         0x0

		# QS Counter Enable
		# PSU_DDR_PHY_DX8SL1DQSCTL_QSCNTEN                                                0x1

		# Unused DQ I/O Mode
		# PSU_DDR_PHY_DX8SL1DQSCTL_UDQIOM                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10                                         0x0

		# Data Slew Rate
		# PSU_DDR_PHY_DX8SL1DQSCTL_DXSR                                                   0x3

		# DQS_N Resistor
		# PSU_DDR_PHY_DX8SL1DQSCTL_DQSNRES                                                0x0

		# DQS Resistor
		# PSU_DDR_PHY_DX8SL1DQSCTL_DQSRES                                                 0x0

		# DATX8 0-1 DQS Control Register
		#(OFFSET, MASK, VALUE)      (0XFD08145C, 0xFFFFFFFFU ,0x01264300U)  */
    mask_write 0XFD08145C 0xFFFFFFFF 0x01264300
		# Register : DX8SL1DXCTL2 @ 0XFD08146C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24                                         0x0

		# Configurable Read Data Enable
		# PSU_DDR_PHY_DX8SL1DXCTL2_CRDEN                                                  0x0

		# OX Extension during Post-amble
		# PSU_DDR_PHY_DX8SL1DXCTL2_POSOEX                                                 0x0

		# OE Extension during Pre-amble
		# PSU_DDR_PHY_DX8SL1DXCTL2_PREOEX                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_17                                            0x0

		# I/O Assisted Gate Select
		# PSU_DDR_PHY_DX8SL1DXCTL2_IOAG                                                   0x0

		# I/O Loopback Select
		# PSU_DDR_PHY_DX8SL1DXCTL2_IOLB                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13                                         0x0

		# Low Power Wakeup Threshold
		# PSU_DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH                                         0xc

		# Read Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL1DXCTL2_RDBI                                                   0x0

		# Write Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL1DXCTL2_WDBI                                                   0x0

		# PUB Read FIFO Bypass
		# PSU_DDR_PHY_DX8SL1DXCTL2_PRFBYP                                                 0x0

		# DATX8 Receive FIFO Read Mode
		# PSU_DDR_PHY_DX8SL1DXCTL2_RDMODE                                                 0x0

		# Disables the Read FIFO Reset
		# PSU_DDR_PHY_DX8SL1DXCTL2_DISRST                                                 0x0

		# Read DQS Gate I/O Loopback
		# PSU_DDR_PHY_DX8SL1DXCTL2_DQSGLB                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_0                                             0x0

		# DATX8 0-1 DX Control Register 2
		#(OFFSET, MASK, VALUE)      (0XFD08146C, 0xFFFFFFFFU ,0x00041800U)  */
    mask_write 0XFD08146C 0xFFFFFFFF 0x00041800
		# Register : DX8SL1IOCR @ 0XFD081470</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL1IOCR_RESERVED_31                                              0x0

		# PVREF_DAC REFSEL range select
		# PSU_DDR_PHY_DX8SL1IOCR_DXDACRANGE                                               0x7

		# IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
		# PSU_DDR_PHY_DX8SL1IOCR_DXVREFIOM                                                0x0

		# DX IO Mode
		# PSU_DDR_PHY_DX8SL1IOCR_DXIOM                                                    0x2

		# DX IO Transmitter Mode
		# PSU_DDR_PHY_DX8SL1IOCR_DXTXM                                                    0x0

		# DX IO Receiver Mode
		# PSU_DDR_PHY_DX8SL1IOCR_DXRXM                                                    0x0

		# DATX8 0-1 I/O Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD081470, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD081470 0xFFFFFFFF 0x70800000
		# Register : DX8SL2OSC @ 0XFD081480</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2OSC_RESERVED_31_30                                            0x0

		# Enable Clock Gating for DX ddr_clk
		# PSU_DDR_PHY_DX8SL2OSC_GATEDXRDCLK                                               0x2

		# Enable Clock Gating for DX ctl_rd_clk
		# PSU_DDR_PHY_DX8SL2OSC_GATEDXDDRCLK                                              0x2

		# Enable Clock Gating for DX ctl_clk
		# PSU_DDR_PHY_DX8SL2OSC_GATEDXCTLCLK                                              0x2

		# Selects the level to which clocks will be stalled when clock gating is e
    # nabled.
		# PSU_DDR_PHY_DX8SL2OSC_CLKLEVEL                                                  0x0

		# Loopback Mode
		# PSU_DDR_PHY_DX8SL2OSC_LBMODE                                                    0x0

		# Load GSDQS LCDL with 2x the calibrated GSDQSPRD value
		# PSU_DDR_PHY_DX8SL2OSC_LBGSDQS                                                   0x0

		# Loopback DQS Gating
		# PSU_DDR_PHY_DX8SL2OSC_LBGDQS                                                    0x0

		# Loopback DQS Shift
		# PSU_DDR_PHY_DX8SL2OSC_LBDQSS                                                    0x0

		# PHY High-Speed Reset
		# PSU_DDR_PHY_DX8SL2OSC_PHYHRST                                                   0x1

		# PHY FIFO Reset
		# PSU_DDR_PHY_DX8SL2OSC_PHYFRST                                                   0x1

		# Delay Line Test Start
		# PSU_DDR_PHY_DX8SL2OSC_DLTST                                                     0x0

		# Delay Line Test Mode
		# PSU_DDR_PHY_DX8SL2OSC_DLTMODE                                                   0x0

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL2OSC_RESERVED_12_11                                            0x3

		# Oscillator Mode Write-Data Delay Line Select
		# PSU_DDR_PHY_DX8SL2OSC_OSCWDDL                                                   0x3

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL2OSC_RESERVED_8_7                                              0x3

		# Oscillator Mode Write-Leveling Delay Line Select
		# PSU_DDR_PHY_DX8SL2OSC_OSCWDL                                                    0x3

		# Oscillator Mode Division
		# PSU_DDR_PHY_DX8SL2OSC_OSCDIV                                                    0xf

		# Oscillator Enable
		# PSU_DDR_PHY_DX8SL2OSC_OSCEN                                                     0x0

		# DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Lo
    # opback, and Gated Clock Control Register
		#(OFFSET, MASK, VALUE)      (0XFD081480, 0xFFFFFFFFU ,0x2A019FFEU)  */
    mask_write 0XFD081480 0xFFFFFFFF 0x2A019FFE
		# Register : DX8SL2PLLCR0 @ 0XFD081484</p>

		# PLL Bypass
		# PSU_DDR_PHY_DX8SL2PLLCR0_PLLBYP                                                 0x0

		# PLL Reset
		# PSU_DDR_PHY_DX8SL2PLLCR0_PLLRST                                                 0x0

		# PLL Power Down
		# PSU_DDR_PHY_DX8SL2PLLCR0_PLLPD                                                  0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_DX8SL2PLLCR0_RSTOPM                                                 0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_DX8SL2PLLCR0_FRQSEL                                                 0x1

		# Relock Mode
		# PSU_DDR_PHY_DX8SL2PLLCR0_RLOCKM                                                 0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_DX8SL2PLLCR0_CPPC                                                   0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_DX8SL2PLLCR0_CPIC                                                   0x0

		# Gear Shift
		# PSU_DDR_PHY_DX8SL2PLLCR0_GSHIFT                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2PLLCR0_RESERVED_11_9                                          0x0

		# Analog Test Enable (ATOEN)
		# PSU_DDR_PHY_DX8SL2PLLCR0_ATOEN                                                  0x0

		# Analog Test Control
		# PSU_DDR_PHY_DX8SL2PLLCR0_ATC                                                    0x0

		# Digital Test Control
		# PSU_DDR_PHY_DX8SL2PLLCR0_DTC                                                    0x0

		# DAXT8 0-1 PLL Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD081484, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD081484 0xFFFFFFFF 0x01100000
		# Register : DX8SL2DQSCTL @ 0XFD08149C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25                                         0x0

		# Read Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL2DQSCTL_RRRMODE                                                0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22                                         0x0

		# Write Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL2DQSCTL_WRRMODE                                                0x1

		# DQS Gate Extension
		# PSU_DDR_PHY_DX8SL2DQSCTL_DQSGX                                                  0x0

		# Low Power PLL Power Down
		# PSU_DDR_PHY_DX8SL2DQSCTL_LPPLLPD                                                0x1

		# Low Power I/O Power Down
		# PSU_DDR_PHY_DX8SL2DQSCTL_LPIOPD                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15                                         0x0

		# QS Counter Enable
		# PSU_DDR_PHY_DX8SL2DQSCTL_QSCNTEN                                                0x1

		# Unused DQ I/O Mode
		# PSU_DDR_PHY_DX8SL2DQSCTL_UDQIOM                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10                                         0x0

		# Data Slew Rate
		# PSU_DDR_PHY_DX8SL2DQSCTL_DXSR                                                   0x3

		# DQS_N Resistor
		# PSU_DDR_PHY_DX8SL2DQSCTL_DQSNRES                                                0x0

		# DQS Resistor
		# PSU_DDR_PHY_DX8SL2DQSCTL_DQSRES                                                 0x0

		# DATX8 0-1 DQS Control Register
		#(OFFSET, MASK, VALUE)      (0XFD08149C, 0xFFFFFFFFU ,0x01264300U)  */
    mask_write 0XFD08149C 0xFFFFFFFF 0x01264300
		# Register : DX8SL2DXCTL2 @ 0XFD0814AC</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24                                         0x0

		# Configurable Read Data Enable
		# PSU_DDR_PHY_DX8SL2DXCTL2_CRDEN                                                  0x0

		# OX Extension during Post-amble
		# PSU_DDR_PHY_DX8SL2DXCTL2_POSOEX                                                 0x0

		# OE Extension during Pre-amble
		# PSU_DDR_PHY_DX8SL2DXCTL2_PREOEX                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_17                                            0x0

		# I/O Assisted Gate Select
		# PSU_DDR_PHY_DX8SL2DXCTL2_IOAG                                                   0x0

		# I/O Loopback Select
		# PSU_DDR_PHY_DX8SL2DXCTL2_IOLB                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13                                         0x0

		# Low Power Wakeup Threshold
		# PSU_DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH                                         0xc

		# Read Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL2DXCTL2_RDBI                                                   0x0

		# Write Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL2DXCTL2_WDBI                                                   0x0

		# PUB Read FIFO Bypass
		# PSU_DDR_PHY_DX8SL2DXCTL2_PRFBYP                                                 0x0

		# DATX8 Receive FIFO Read Mode
		# PSU_DDR_PHY_DX8SL2DXCTL2_RDMODE                                                 0x0

		# Disables the Read FIFO Reset
		# PSU_DDR_PHY_DX8SL2DXCTL2_DISRST                                                 0x0

		# Read DQS Gate I/O Loopback
		# PSU_DDR_PHY_DX8SL2DXCTL2_DQSGLB                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_0                                             0x0

		# DATX8 0-1 DX Control Register 2
		#(OFFSET, MASK, VALUE)      (0XFD0814AC, 0xFFFFFFFFU ,0x00041800U)  */
    mask_write 0XFD0814AC 0xFFFFFFFF 0x00041800
		# Register : DX8SL2IOCR @ 0XFD0814B0</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL2IOCR_RESERVED_31                                              0x0

		# PVREF_DAC REFSEL range select
		# PSU_DDR_PHY_DX8SL2IOCR_DXDACRANGE                                               0x7

		# IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
		# PSU_DDR_PHY_DX8SL2IOCR_DXVREFIOM                                                0x0

		# DX IO Mode
		# PSU_DDR_PHY_DX8SL2IOCR_DXIOM                                                    0x2

		# DX IO Transmitter Mode
		# PSU_DDR_PHY_DX8SL2IOCR_DXTXM                                                    0x0

		# DX IO Receiver Mode
		# PSU_DDR_PHY_DX8SL2IOCR_DXRXM                                                    0x0

		# DATX8 0-1 I/O Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD0814B0, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD0814B0 0xFFFFFFFF 0x70800000
		# Register : DX8SL3OSC @ 0XFD0814C0</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3OSC_RESERVED_31_30                                            0x0

		# Enable Clock Gating for DX ddr_clk
		# PSU_DDR_PHY_DX8SL3OSC_GATEDXRDCLK                                               0x2

		# Enable Clock Gating for DX ctl_rd_clk
		# PSU_DDR_PHY_DX8SL3OSC_GATEDXDDRCLK                                              0x2

		# Enable Clock Gating for DX ctl_clk
		# PSU_DDR_PHY_DX8SL3OSC_GATEDXCTLCLK                                              0x2

		# Selects the level to which clocks will be stalled when clock gating is e
    # nabled.
		# PSU_DDR_PHY_DX8SL3OSC_CLKLEVEL                                                  0x0

		# Loopback Mode
		# PSU_DDR_PHY_DX8SL3OSC_LBMODE                                                    0x0

		# Load GSDQS LCDL with 2x the calibrated GSDQSPRD value
		# PSU_DDR_PHY_DX8SL3OSC_LBGSDQS                                                   0x0

		# Loopback DQS Gating
		# PSU_DDR_PHY_DX8SL3OSC_LBGDQS                                                    0x0

		# Loopback DQS Shift
		# PSU_DDR_PHY_DX8SL3OSC_LBDQSS                                                    0x0

		# PHY High-Speed Reset
		# PSU_DDR_PHY_DX8SL3OSC_PHYHRST                                                   0x1

		# PHY FIFO Reset
		# PSU_DDR_PHY_DX8SL3OSC_PHYFRST                                                   0x1

		# Delay Line Test Start
		# PSU_DDR_PHY_DX8SL3OSC_DLTST                                                     0x0

		# Delay Line Test Mode
		# PSU_DDR_PHY_DX8SL3OSC_DLTMODE                                                   0x0

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL3OSC_RESERVED_12_11                                            0x3

		# Oscillator Mode Write-Data Delay Line Select
		# PSU_DDR_PHY_DX8SL3OSC_OSCWDDL                                                   0x3

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL3OSC_RESERVED_8_7                                              0x3

		# Oscillator Mode Write-Leveling Delay Line Select
		# PSU_DDR_PHY_DX8SL3OSC_OSCWDL                                                    0x3

		# Oscillator Mode Division
		# PSU_DDR_PHY_DX8SL3OSC_OSCDIV                                                    0xf

		# Oscillator Enable
		# PSU_DDR_PHY_DX8SL3OSC_OSCEN                                                     0x0

		# DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Lo
    # opback, and Gated Clock Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0814C0, 0xFFFFFFFFU ,0x2A019FFEU)  */
    mask_write 0XFD0814C0 0xFFFFFFFF 0x2A019FFE
		# Register : DX8SL3PLLCR0 @ 0XFD0814C4</p>

		# PLL Bypass
		# PSU_DDR_PHY_DX8SL3PLLCR0_PLLBYP                                                 0x0

		# PLL Reset
		# PSU_DDR_PHY_DX8SL3PLLCR0_PLLRST                                                 0x0

		# PLL Power Down
		# PSU_DDR_PHY_DX8SL3PLLCR0_PLLPD                                                  0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_DX8SL3PLLCR0_RSTOPM                                                 0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_DX8SL3PLLCR0_FRQSEL                                                 0x1

		# Relock Mode
		# PSU_DDR_PHY_DX8SL3PLLCR0_RLOCKM                                                 0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_DX8SL3PLLCR0_CPPC                                                   0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_DX8SL3PLLCR0_CPIC                                                   0x0

		# Gear Shift
		# PSU_DDR_PHY_DX8SL3PLLCR0_GSHIFT                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3PLLCR0_RESERVED_11_9                                          0x0

		# Analog Test Enable (ATOEN)
		# PSU_DDR_PHY_DX8SL3PLLCR0_ATOEN                                                  0x0

		# Analog Test Control
		# PSU_DDR_PHY_DX8SL3PLLCR0_ATC                                                    0x0

		# Digital Test Control
		# PSU_DDR_PHY_DX8SL3PLLCR0_DTC                                                    0x0

		# DAXT8 0-1 PLL Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0814C4, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD0814C4 0xFFFFFFFF 0x01100000
		# Register : DX8SL3DQSCTL @ 0XFD0814DC</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25                                         0x0

		# Read Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL3DQSCTL_RRRMODE                                                0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22                                         0x0

		# Write Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL3DQSCTL_WRRMODE                                                0x1

		# DQS Gate Extension
		# PSU_DDR_PHY_DX8SL3DQSCTL_DQSGX                                                  0x0

		# Low Power PLL Power Down
		# PSU_DDR_PHY_DX8SL3DQSCTL_LPPLLPD                                                0x1

		# Low Power I/O Power Down
		# PSU_DDR_PHY_DX8SL3DQSCTL_LPIOPD                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15                                         0x0

		# QS Counter Enable
		# PSU_DDR_PHY_DX8SL3DQSCTL_QSCNTEN                                                0x1

		# Unused DQ I/O Mode
		# PSU_DDR_PHY_DX8SL3DQSCTL_UDQIOM                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10                                         0x0

		# Data Slew Rate
		# PSU_DDR_PHY_DX8SL3DQSCTL_DXSR                                                   0x3

		# DQS_N Resistor
		# PSU_DDR_PHY_DX8SL3DQSCTL_DQSNRES                                                0x0

		# DQS Resistor
		# PSU_DDR_PHY_DX8SL3DQSCTL_DQSRES                                                 0x0

		# DATX8 0-1 DQS Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0814DC, 0xFFFFFFFFU ,0x01264300U)  */
    mask_write 0XFD0814DC 0xFFFFFFFF 0x01264300
		# Register : DX8SL3DXCTL2 @ 0XFD0814EC</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24                                         0x0

		# Configurable Read Data Enable
		# PSU_DDR_PHY_DX8SL3DXCTL2_CRDEN                                                  0x0

		# OX Extension during Post-amble
		# PSU_DDR_PHY_DX8SL3DXCTL2_POSOEX                                                 0x0

		# OE Extension during Pre-amble
		# PSU_DDR_PHY_DX8SL3DXCTL2_PREOEX                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_17                                            0x0

		# I/O Assisted Gate Select
		# PSU_DDR_PHY_DX8SL3DXCTL2_IOAG                                                   0x0

		# I/O Loopback Select
		# PSU_DDR_PHY_DX8SL3DXCTL2_IOLB                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13                                         0x0

		# Low Power Wakeup Threshold
		# PSU_DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH                                         0xc

		# Read Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL3DXCTL2_RDBI                                                   0x0

		# Write Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL3DXCTL2_WDBI                                                   0x0

		# PUB Read FIFO Bypass
		# PSU_DDR_PHY_DX8SL3DXCTL2_PRFBYP                                                 0x0

		# DATX8 Receive FIFO Read Mode
		# PSU_DDR_PHY_DX8SL3DXCTL2_RDMODE                                                 0x0

		# Disables the Read FIFO Reset
		# PSU_DDR_PHY_DX8SL3DXCTL2_DISRST                                                 0x0

		# Read DQS Gate I/O Loopback
		# PSU_DDR_PHY_DX8SL3DXCTL2_DQSGLB                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_0                                             0x0

		# DATX8 0-1 DX Control Register 2
		#(OFFSET, MASK, VALUE)      (0XFD0814EC, 0xFFFFFFFFU ,0x00041800U)  */
    mask_write 0XFD0814EC 0xFFFFFFFF 0x00041800
		# Register : DX8SL3IOCR @ 0XFD0814F0</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL3IOCR_RESERVED_31                                              0x0

		# PVREF_DAC REFSEL range select
		# PSU_DDR_PHY_DX8SL3IOCR_DXDACRANGE                                               0x7

		# IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
		# PSU_DDR_PHY_DX8SL3IOCR_DXVREFIOM                                                0x0

		# DX IO Mode
		# PSU_DDR_PHY_DX8SL3IOCR_DXIOM                                                    0x2

		# DX IO Transmitter Mode
		# PSU_DDR_PHY_DX8SL3IOCR_DXTXM                                                    0x0

		# DX IO Receiver Mode
		# PSU_DDR_PHY_DX8SL3IOCR_DXRXM                                                    0x0

		# DATX8 0-1 I/O Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD0814F0, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD0814F0 0xFFFFFFFF 0x70800000
		# Register : DX8SL4OSC @ 0XFD081500</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4OSC_RESERVED_31_30                                            0x0

		# Enable Clock Gating for DX ddr_clk
		# PSU_DDR_PHY_DX8SL4OSC_GATEDXRDCLK                                               0x2

		# Enable Clock Gating for DX ctl_rd_clk
		# PSU_DDR_PHY_DX8SL4OSC_GATEDXDDRCLK                                              0x2

		# Enable Clock Gating for DX ctl_clk
		# PSU_DDR_PHY_DX8SL4OSC_GATEDXCTLCLK                                              0x2

		# Selects the level to which clocks will be stalled when clock gating is e
    # nabled.
		# PSU_DDR_PHY_DX8SL4OSC_CLKLEVEL                                                  0x0

		# Loopback Mode
		# PSU_DDR_PHY_DX8SL4OSC_LBMODE                                                    0x0

		# Load GSDQS LCDL with 2x the calibrated GSDQSPRD value
		# PSU_DDR_PHY_DX8SL4OSC_LBGSDQS                                                   0x0

		# Loopback DQS Gating
		# PSU_DDR_PHY_DX8SL4OSC_LBGDQS                                                    0x0

		# Loopback DQS Shift
		# PSU_DDR_PHY_DX8SL4OSC_LBDQSS                                                    0x0

		# PHY High-Speed Reset
		# PSU_DDR_PHY_DX8SL4OSC_PHYHRST                                                   0x1

		# PHY FIFO Reset
		# PSU_DDR_PHY_DX8SL4OSC_PHYFRST                                                   0x1

		# Delay Line Test Start
		# PSU_DDR_PHY_DX8SL4OSC_DLTST                                                     0x0

		# Delay Line Test Mode
		# PSU_DDR_PHY_DX8SL4OSC_DLTMODE                                                   0x0

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL4OSC_RESERVED_12_11                                            0x3

		# Oscillator Mode Write-Data Delay Line Select
		# PSU_DDR_PHY_DX8SL4OSC_OSCWDDL                                                   0x3

		# Reserved. Caution, do not write to this register field.
		# PSU_DDR_PHY_DX8SL4OSC_RESERVED_8_7                                              0x3

		# Oscillator Mode Write-Leveling Delay Line Select
		# PSU_DDR_PHY_DX8SL4OSC_OSCWDL                                                    0x3

		# Oscillator Mode Division
		# PSU_DDR_PHY_DX8SL4OSC_OSCDIV                                                    0xf

		# Oscillator Enable
		# PSU_DDR_PHY_DX8SL4OSC_OSCEN                                                     0x0

		# DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Lo
    # opback, and Gated Clock Control Register
		#(OFFSET, MASK, VALUE)      (0XFD081500, 0xFFFFFFFFU ,0x2A019FFEU)  */
    mask_write 0XFD081500 0xFFFFFFFF 0x2A019FFE
		# Register : DX8SL4PLLCR0 @ 0XFD081504</p>

		# PLL Bypass
		# PSU_DDR_PHY_DX8SL4PLLCR0_PLLBYP                                                 0x0

		# PLL Reset
		# PSU_DDR_PHY_DX8SL4PLLCR0_PLLRST                                                 0x0

		# PLL Power Down
		# PSU_DDR_PHY_DX8SL4PLLCR0_PLLPD                                                  0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_DX8SL4PLLCR0_RSTOPM                                                 0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_DX8SL4PLLCR0_FRQSEL                                                 0x1

		# Relock Mode
		# PSU_DDR_PHY_DX8SL4PLLCR0_RLOCKM                                                 0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_DX8SL4PLLCR0_CPPC                                                   0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_DX8SL4PLLCR0_CPIC                                                   0x0

		# Gear Shift
		# PSU_DDR_PHY_DX8SL4PLLCR0_GSHIFT                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4PLLCR0_RESERVED_11_9                                          0x0

		# Analog Test Enable (ATOEN)
		# PSU_DDR_PHY_DX8SL4PLLCR0_ATOEN                                                  0x0

		# Analog Test Control
		# PSU_DDR_PHY_DX8SL4PLLCR0_ATC                                                    0x0

		# Digital Test Control
		# PSU_DDR_PHY_DX8SL4PLLCR0_DTC                                                    0x0

		# DAXT8 0-1 PLL Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD081504, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD081504 0xFFFFFFFF 0x01100000
		# Register : DX8SL4DQSCTL @ 0XFD08151C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25                                         0x0

		# Read Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL4DQSCTL_RRRMODE                                                0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22                                         0x0

		# Write Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SL4DQSCTL_WRRMODE                                                0x1

		# DQS Gate Extension
		# PSU_DDR_PHY_DX8SL4DQSCTL_DQSGX                                                  0x0

		# Low Power PLL Power Down
		# PSU_DDR_PHY_DX8SL4DQSCTL_LPPLLPD                                                0x1

		# Low Power I/O Power Down
		# PSU_DDR_PHY_DX8SL4DQSCTL_LPIOPD                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15                                         0x0

		# QS Counter Enable
		# PSU_DDR_PHY_DX8SL4DQSCTL_QSCNTEN                                                0x1

		# Unused DQ I/O Mode
		# PSU_DDR_PHY_DX8SL4DQSCTL_UDQIOM                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10                                         0x0

		# Data Slew Rate
		# PSU_DDR_PHY_DX8SL4DQSCTL_DXSR                                                   0x3

		# DQS_N Resistor
		# PSU_DDR_PHY_DX8SL4DQSCTL_DQSNRES                                                0x0

		# DQS Resistor
		# PSU_DDR_PHY_DX8SL4DQSCTL_DQSRES                                                 0x0

		# DATX8 0-1 DQS Control Register
		#(OFFSET, MASK, VALUE)      (0XFD08151C, 0xFFFFFFFFU ,0x01264300U)  */
    mask_write 0XFD08151C 0xFFFFFFFF 0x01264300
		# Register : DX8SL4DXCTL2 @ 0XFD08152C</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24                                         0x0

		# Configurable Read Data Enable
		# PSU_DDR_PHY_DX8SL4DXCTL2_CRDEN                                                  0x0

		# OX Extension during Post-amble
		# PSU_DDR_PHY_DX8SL4DXCTL2_POSOEX                                                 0x0

		# OE Extension during Pre-amble
		# PSU_DDR_PHY_DX8SL4DXCTL2_PREOEX                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_17                                            0x0

		# I/O Assisted Gate Select
		# PSU_DDR_PHY_DX8SL4DXCTL2_IOAG                                                   0x0

		# I/O Loopback Select
		# PSU_DDR_PHY_DX8SL4DXCTL2_IOLB                                                   0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13                                         0x0

		# Low Power Wakeup Threshold
		# PSU_DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH                                         0xc

		# Read Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL4DXCTL2_RDBI                                                   0x0

		# Write Data Bus Inversion Enable
		# PSU_DDR_PHY_DX8SL4DXCTL2_WDBI                                                   0x0

		# PUB Read FIFO Bypass
		# PSU_DDR_PHY_DX8SL4DXCTL2_PRFBYP                                                 0x0

		# DATX8 Receive FIFO Read Mode
		# PSU_DDR_PHY_DX8SL4DXCTL2_RDMODE                                                 0x0

		# Disables the Read FIFO Reset
		# PSU_DDR_PHY_DX8SL4DXCTL2_DISRST                                                 0x0

		# Read DQS Gate I/O Loopback
		# PSU_DDR_PHY_DX8SL4DXCTL2_DQSGLB                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_0                                             0x0

		# DATX8 0-1 DX Control Register 2
		#(OFFSET, MASK, VALUE)      (0XFD08152C, 0xFFFFFFFFU ,0x00041800U)  */
    mask_write 0XFD08152C 0xFFFFFFFF 0x00041800
		# Register : DX8SL4IOCR @ 0XFD081530</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SL4IOCR_RESERVED_31                                              0x0

		# PVREF_DAC REFSEL range select
		# PSU_DDR_PHY_DX8SL4IOCR_DXDACRANGE                                               0x7

		# IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
		# PSU_DDR_PHY_DX8SL4IOCR_DXVREFIOM                                                0x0

		# DX IO Mode
		# PSU_DDR_PHY_DX8SL4IOCR_DXIOM                                                    0x2

		# DX IO Transmitter Mode
		# PSU_DDR_PHY_DX8SL4IOCR_DXTXM                                                    0x0

		# DX IO Receiver Mode
		# PSU_DDR_PHY_DX8SL4IOCR_DXRXM                                                    0x0

		# DATX8 0-1 I/O Configuration Register
		#(OFFSET, MASK, VALUE)      (0XFD081530, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD081530 0xFFFFFFFF 0x70800000
		# Register : DX8SLbPLLCR0 @ 0XFD0817C4</p>

		# PLL Bypass
		# PSU_DDR_PHY_DX8SLBPLLCR0_PLLBYP                                                 0x0

		# PLL Reset
		# PSU_DDR_PHY_DX8SLBPLLCR0_PLLRST                                                 0x0

		# PLL Power Down
		# PSU_DDR_PHY_DX8SLBPLLCR0_PLLPD                                                  0x0

		# Reference Stop Mode
		# PSU_DDR_PHY_DX8SLBPLLCR0_RSTOPM                                                 0x0

		# PLL Frequency Select
		# PSU_DDR_PHY_DX8SLBPLLCR0_FRQSEL                                                 0x1

		# Relock Mode
		# PSU_DDR_PHY_DX8SLBPLLCR0_RLOCKM                                                 0x0

		# Charge Pump Proportional Current Control
		# PSU_DDR_PHY_DX8SLBPLLCR0_CPPC                                                   0x8

		# Charge Pump Integrating Current Control
		# PSU_DDR_PHY_DX8SLBPLLCR0_CPIC                                                   0x0

		# Gear Shift
		# PSU_DDR_PHY_DX8SLBPLLCR0_GSHIFT                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SLBPLLCR0_RESERVED_11_9                                          0x0

		# Analog Test Enable (ATOEN)
		# PSU_DDR_PHY_DX8SLBPLLCR0_ATOEN                                                  0x0

		# Analog Test Control
		# PSU_DDR_PHY_DX8SLBPLLCR0_ATC                                                    0x0

		# Digital Test Control
		# PSU_DDR_PHY_DX8SLBPLLCR0_DTC                                                    0x0

		# DAXT8 0-8 PLL Control Register 0
		#(OFFSET, MASK, VALUE)      (0XFD0817C4, 0xFFFFFFFFU ,0x01100000U)  */
    mask_write 0XFD0817C4 0xFFFFFFFF 0x01100000
		# Register : DX8SLbDQSCTL @ 0XFD0817DC</p>

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25                                         0x0

		# Read Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SLBDQSCTL_RRRMODE                                                0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22                                         0x0

		# Write Path Rise-to-Rise Mode
		# PSU_DDR_PHY_DX8SLBDQSCTL_WRRMODE                                                0x1

		# DQS Gate Extension
		# PSU_DDR_PHY_DX8SLBDQSCTL_DQSGX                                                  0x0

		# Low Power PLL Power Down
		# PSU_DDR_PHY_DX8SLBDQSCTL_LPPLLPD                                                0x1

		# Low Power I/O Power Down
		# PSU_DDR_PHY_DX8SLBDQSCTL_LPIOPD                                                 0x1

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15                                         0x0

		# QS Counter Enable
		# PSU_DDR_PHY_DX8SLBDQSCTL_QSCNTEN                                                0x1

		# Unused DQ I/O Mode
		# PSU_DDR_PHY_DX8SLBDQSCTL_UDQIOM                                                 0x0

		# Reserved. Return zeroes on reads.
		# PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10                                         0x0

		# Data Slew Rate
		# PSU_DDR_PHY_DX8SLBDQSCTL_DXSR                                                   0x3

		# DQS# Resistor
		# PSU_DDR_PHY_DX8SLBDQSCTL_DQSNRES                                                0xc

		# DQS Resistor
		# PSU_DDR_PHY_DX8SLBDQSCTL_DQSRES                                                 0x4

		# DATX8 0-8 DQS Control Register
		#(OFFSET, MASK, VALUE)      (0XFD0817DC, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD0817DC 0xFFFFFFFF 0x012643C4
}

set psu_ddr_qos_init_data {
}

set psu_mio_init_data {
		# : MIO PROGRAMMING
		# Register : MIO_PIN_0 @ 0XFF180000</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out-
    #  (QSPI Clock)
		# PSU_IOU_SLCR_MIO_PIN_0_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_0_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[0]- (Test Scan Port) = test_scan, Output, test_scan_out[0
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_0_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[0]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[0]- (GPIO bank 0) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= pjtag, Input, pjtag_tck- (PJTAG
    #  TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sc
    # lk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Out
    # put, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_c
    # lk- (Trace Port Clock)
		# PSU_IOU_SLCR_MIO_PIN_0_L3_SEL                                                   0

		# Configures MIO Pin 0 peripheral interface mapping. S
		#(OFFSET, MASK, VALUE)      (0XFF180000, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180000 0x000000FE 0x00000002
		# Register : MIO_PIN_1 @ 0XFF180004</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_mi1- (Q
    # SPI Databus) 1= qspi, Output, qspi_so_mo1- (QSPI Databus)
		# PSU_IOU_SLCR_MIO_PIN_1_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_1_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[1]- (Test Scan Port) = test_scan, Output, test_scan_out[1
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_1_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[1]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[1]- (GPIO bank 0) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tdi- (PJTAG
    # TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc3, Ou
    # tput, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART
    # receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control
    # Signal)
		# PSU_IOU_SLCR_MIO_PIN_1_L3_SEL                                                   0

		# Configures MIO Pin 1 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180004, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180004 0x000000FE 0x00000002
		# Register : MIO_PIN_2 @ 0XFF180008</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi2- (QSPI
    #  Databus) 1= qspi, Output, qspi_mo2- (QSPI Databus)
		# PSU_IOU_SLCR_MIO_PIN_2_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_2_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[2]- (Test Scan Port) = test_scan, Output, test_scan_out[2
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_2_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[2]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[2]- (GPIO bank 0) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= pjtag, Output, pjtag_tdo- (PJTAG
    #  TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc2, I
    # nput, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver se
    # rial input) 7= trace, Output, tracedq[0]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_2_L3_SEL                                                   0

		# Configures MIO Pin 2 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180008, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180008 0x000000FE 0x00000002
		# Register : MIO_PIN_3 @ 0XFF18000C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi3- (QSPI
    #  Databus) 1= qspi, Output, qspi_mo3- (QSPI Databus)
		# PSU_IOU_SLCR_MIO_PIN_3_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_3_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[3]- (Test Scan Port) = test_scan, Output, test_scan_out[3
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_3_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[3]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[3]- (GPIO bank 0) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tms- (PJTAG
    #  TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output
    # , spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out-
    #  (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial
    # output) 7= trace, Output, tracedq[1]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_3_L3_SEL                                                   0

		# Configures MIO Pin 3 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18000C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18000C 0x000000FE 0x00000002
		# Register : MIO_PIN_4 @ 0XFF180010</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_mo_mo0- (
    # QSPI Databus) 1= qspi, Input, qspi_si_mi0- (QSPI Databus)
		# PSU_IOU_SLCR_MIO_PIN_4_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_4_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[4]- (Test Scan Port) = test_scan, Output, test_scan_out[4
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_4_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[4]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[4]- (GPIO bank 0) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (Wa
    # tch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi
    # 0, Output, spi0_so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Cloc
    # k) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, O
    # utput, tracedq[2]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_4_L3_SEL                                                   0

		# Configures MIO Pin 4 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180010, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180010 0x000000FE 0x00000002
		# Register : MIO_PIN_5 @ 0XFF180014</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out-
    #  (QSPI Slave Select)
		# PSU_IOU_SLCR_MIO_PIN_5_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_5_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[5]- (Test Scan Port) = test_scan, Output, test_scan_out[5
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_5_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[5]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[5]- (GPIO bank 0) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out- (W
    # atch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4=
    # spi0, Input, spi0_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC
    #  Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7=
    #  trace, Output, tracedq[3]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_5_L3_SEL                                                   0

		# Configures MIO Pin 5 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180014, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180014 0x000000FE 0x00000002
		# Register : MIO_PIN_6 @ 0XFF180018</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_clk_for_l
    # pbk- (QSPI Clock to be fed-back)
		# PSU_IOU_SLCR_MIO_PIN_6_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_6_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[6]- (Test Scan Port) = test_scan, Output, test_scan_out[6
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_6_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[6]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[6]- (GPIO bank 0) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (Wat
    # ch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= s
    # pi1, Output, spi1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TT
    # C Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace,
    # Output, tracedq[4]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_6_L3_SEL                                                   0

		# Configures MIO Pin 6 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180018, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180018 0x000000FE 0x00000002
		# Register : MIO_PIN_7 @ 0XFF18001C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out_
    # upper- (QSPI Slave Select upper)
		# PSU_IOU_SLCR_MIO_PIN_7_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_7_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[7]- (Test Scan Port) = test_scan, Output, test_scan_out[7
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_7_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[7]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[7]- (GPIO bank 0) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out- (
    # Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Ma
    # ster Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua
    # 0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, t
    # racedq[5]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_7_L3_SEL                                                   0

		# Configures MIO Pin 7 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18001C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18001C 0x000000FE 0x00000002
		# Register : MIO_PIN_8 @ 0XFF180020</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[0
    # ]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_upper[0]- (QSPI Upper D
    # atabus)
		# PSU_IOU_SLCR_MIO_PIN_8_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_8_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[8]- (Test Scan Port) = test_scan, Output, test_scan_out[8
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_8_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[8]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[8]- (GPIO bank 0) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (Wa
    # tch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Maste
    # r Selects) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_
    # txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Tra
    # ce Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_8_L3_SEL                                                   0

		# Configures MIO Pin 8 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180020, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180020 0x000000FE 0x00000002
		# Register : MIO_PIN_9 @ 0XFF180024</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[1
    # ]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_upper[1]- (QSPI Upper D
    # atabus)
		# PSU_IOU_SLCR_MIO_PIN_9_L0_SEL                                                   1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NA
    # ND chip enable)
		# PSU_IOU_SLCR_MIO_PIN_9_L1_SEL                                                   0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[9]- (Test Scan Port) = test_scan, Output, test_scan_out[9
    # ]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_9_L2_SEL                                                   0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[9]- (GPIO bank 0) 0= g
    # pio0, Output, gpio_0_pin_out[9]- (GPIO bank 0) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out- (W
    # atch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master S
    # elects) 4= spi1, Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc3,
    #  Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UA
    # RT receiver serial input) 7= trace, Output, tracedq[7]- (Trace Port Data
    # bus)
		# PSU_IOU_SLCR_MIO_PIN_9_L3_SEL                                                   0

		# Configures MIO Pin 9 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180024, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180024 0x000000FE 0x00000002
		# Register : MIO_PIN_10 @ 0XFF180028</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[2
    # ]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_upper[2]- (QSPI Upper D
    # atabus)
		# PSU_IOU_SLCR_MIO_PIN_10_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (N
    # AND Ready/Busy)
		# PSU_IOU_SLCR_MIO_PIN_10_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[10]- (Test Scan Port) = test_scan, Output, test_scan_out[
    # 10]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_10_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[10]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[10]- (GPIO bank 0) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= sp
    # i1, Output, spi1_so- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clo
    # ck) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outpu
    # t, tracedq[8]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_10_L3_SEL                                                  0

		# Configures MIO Pin 10 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180028, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180028 0x000000FE 0x00000002
		# Register : MIO_PIN_11 @ 0XFF18002C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[3
    # ]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_upper[3]- (QSPI Upper D
    # atabus)
		# PSU_IOU_SLCR_MIO_PIN_11_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (N
    # AND Ready/Busy)
		# PSU_IOU_SLCR_MIO_PIN_11_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[11]- (Test Scan Port) = test_scan, Output, test_scan_out[
    # 11]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_11_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[11]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[11]- (GPIO bank 0) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal)
    # 4= spi1, Input, spi1_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (
    # TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial ou
    # tput) 7= trace, Output, tracedq[9]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_11_L3_SEL                                                  0

		# Configures MIO Pin 11 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18002C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18002C 0x000000FE 0x00000002
		# Register : MIO_PIN_12 @ 0XFF180030</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out_
    # upper- (QSPI Upper Clock)
		# PSU_IOU_SLCR_MIO_PIN_12_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NA
    # ND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe)
		# PSU_IOU_SLCR_MIO_PIN_12_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input
    # , test_scan_in[12]- (Test Scan Port) = test_scan, Output, test_scan_out[
    # 12]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_12_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[12]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[12]- (GPIO bank 0) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= pjtag, Input, pjtag_tck- (PJT
    # AG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_
    # sclk_out- (SPI Clock) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, O
    # utput, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace
    # dq[10]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_12_L3_SEL                                                  0

		# Configures MIO Pin 12 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180030, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180030 0x000000FE 0x00000002
		# Register : MIO_PIN_13 @ 0XFF180034</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_13_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[0]- (NA
    # ND chip enable)
		# PSU_IOU_SLCR_MIO_PIN_13_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[13]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[13]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_13_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[13]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[13]- (GPIO bank 0) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tdi- (PJTA
    # G TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1,
    # Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UAR
    # T receiver serial input) 7= trace, Output, tracedq[11]- (Trace Port Data
    # bus)
		# PSU_IOU_SLCR_MIO_PIN_13_L3_SEL                                                  0

		# Configures MIO Pin 13 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180034, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180034 0x000000FE 0x00000000
		# Register : MIO_PIN_14 @ 0XFF180038</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_14_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_cle- (NAND
    #  Command Latch Enable)
		# PSU_IOU_SLCR_MIO_PIN_14_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[14]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[14]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_14_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[14]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[14]- (GPIO bank 0) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= pjtag, Output, pjtag_tdo- (PJT
    # AG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0,
    #  Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver
    # serial input) 7= trace, Output, tracedq[12]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_14_L3_SEL                                                  2

		# Configures MIO Pin 14 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180038, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF180038 0x000000FE 0x00000040
		# Register : MIO_PIN_15 @ 0XFF18003C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_15_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ale- (NAND
    #  Address Latch Enable)
		# PSU_IOU_SLCR_MIO_PIN_15_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[15]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[15]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_15_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[15]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[15]- (GPIO bank 0) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tms- (PJT
    # AG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Outp
    # ut, spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_ou
    # t- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter seria
    # l output) 7= trace, Output, tracedq[13]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_15_L3_SEL                                                  2

		# Configures MIO Pin 15 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18003C, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF18003C 0x000000FE 0x00000040
		# Register : MIO_PIN_16 @ 0XFF180040</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_16_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[0]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[0]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_16_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[16]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[16]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_16_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[16]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[16]- (GPIO bank 0) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= s
    # pi0, Output, spi0_so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Cl
    # ock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace,
    #  Output, tracedq[14]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_16_L3_SEL                                                  2

		# Configures MIO Pin 16 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180040, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF180040 0x000000FE 0x00000040
		# Register : MIO_PIN_17 @ 0XFF180044</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_17_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[1]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[1]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_17_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[17]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[17]- (Test Scan Port) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_17_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[17]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[17]- (GPIO bank 0) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4
    # = spi0, Input, spi0_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (T
    # TC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
    # 7= trace, Output, tracedq[15]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_17_L3_SEL                                                  2

		# Configures MIO Pin 17 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180044, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF180044 0x000000FE 0x00000040
		# Register : MIO_PIN_18 @ 0XFF180048</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_18_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[2]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[2]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_18_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[18]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[18]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU
    #  Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_18_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[18]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[18]- (GPIO bank 0) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= sp
    # i1, Output, spi1_so- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clo
    # ck) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_18_L3_SEL                                                  6

		# Configures MIO Pin 18 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180048, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180048 0x000000FE 0x000000C0
		# Register : MIO_PIN_19 @ 0XFF18004C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_19_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[3]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[3]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_19_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[19]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[19]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU
    #  Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_19_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[19]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[19]- (GPIO bank 0) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI
    # Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6=
    # ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_19_L3_SEL                                                  6

		# Configures MIO Pin 19 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18004C, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF18004C 0x000000FE 0x000000C0
		# Register : MIO_PIN_20 @ 0XFF180050</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_20_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[4]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[4]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_20_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8-bit Data bus) 2= t
    # est_scan, Input, test_scan_in[20]- (Test Scan Port) = test_scan, Output,
    #  test_scan_out[20]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU
    #  Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_20_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[20]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[20]- (GPIO bank 0) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Mas
    # ter Selects) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua
    # 1_txd- (UART transmitter serial output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_20_L3_SEL                                                  6

		# Configures MIO Pin 20 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180050, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180050 0x000000FE 0x000000C0
		# Register : MIO_PIN_21 @ 0XFF180054</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_21_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[5]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[5]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_21_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Com
    # mand Indicator) = sd0, Output, sdio0_cmd_out- (Command Indicator) 2= tes
    # t_scan, Input, test_scan_in[21]- (Test Scan Port) = test_scan, Output, t
    # est_scan_out[21]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU E
    # xt Tamper)
		# PSU_IOU_SLCR_MIO_PIN_21_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[21]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[21]- (GPIO bank 0) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master
    #  Selects) 4= spi1, Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc
    # 1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (
    # UART receiver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_21_L3_SEL                                                  6

		# Configures MIO Pin 21 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180054, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180054 0x000000FE 0x000000C0
		# Register : MIO_PIN_22 @ 0XFF180058</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_22_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_we_b- (NAN
    # D Write Enable)
		# PSU_IOU_SLCR_MIO_PIN_22_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out-
    # (SDSDIO clock) 2= test_scan, Input, test_scan_in[22]- (Test Scan Port) =
    #  test_scan, Output, test_scan_out[22]- (Test Scan Port) 3= csu, Input, c
    # su_ext_tamper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_22_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[22]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[22]- (GPIO bank 0) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4=
    #  spi1, Output, spi1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (
    # TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not U
    # sed
		# PSU_IOU_SLCR_MIO_PIN_22_L3_SEL                                                  0

		# Configures MIO Pin 22 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180058, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180058 0x000000FE 0x00000000
		# Register : MIO_PIN_23 @ 0XFF18005C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_23_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[6]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[6]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_23_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow-
    # (SD card bus power) 2= test_scan, Input, test_scan_in[23]- (Test Scan Po
    # rt) = test_scan, Output, test_scan_out[23]- (Test Scan Port) 3= csu, Inp
    # ut, csu_ext_tamper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_23_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[23]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[23]- (GPIO bank 0) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal)
    # 4= spi1, Input, spi1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (
    # TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial ou
    # tput) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_23_L3_SEL                                                  0

		# Configures MIO Pin 23 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18005C, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF18005C 0x000000FE 0x00000000
		# Register : MIO_PIN_24 @ 0XFF180060</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_24_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[7]- (
    # NAND Data Bus) 1= nand, Output, nfc_dq_out[7]- (NAND Data Bus)
		# PSU_IOU_SLCR_MIO_PIN_24_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD
    # card detect from connector) 2= test_scan, Input, test_scan_in[24]- (Test
    #  Scan Port) = test_scan, Output, test_scan_out[24]- (Test Scan Port) 3=
    # csu, Input, csu_ext_tamper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_24_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[24]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[24]- (GPIO bank 0) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= Not Used 5= ttc3, Input, ttc3_clk_in- (T
    # TC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= N
    # ot Used
		# PSU_IOU_SLCR_MIO_PIN_24_L3_SEL                                                  1

		# Configures MIO Pin 24 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180060, 0x000000FEU ,0x00000020U)  */
    mask_write 0XFF180060 0x000000FE 0x00000020
		# Register : MIO_PIN_25 @ 0XFF180064</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_25_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_re_n- (NAN
    # D Read Enable)
		# PSU_IOU_SLCR_MIO_PIN_25_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD ca
    # rd write protect from connector) 2= test_scan, Input, test_scan_in[25]-
    # (Test Scan Port) = test_scan, Output, test_scan_out[25]- (Test Scan Port
    # ) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_25_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[25]- (GPIO bank 0) 0=
    # gpio0, Output, gpio_0_pin_out[25]- (GPIO bank 0) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= Not Used 5= ttc3, Output, ttc3_wave_ou
    # t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial in
    # put) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_25_L3_SEL                                                  1

		# Configures MIO Pin 25 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180064, 0x000000FEU ,0x00000020U)  */
    mask_write 0XFF180064 0x000000FE 0x00000020
		# Register : MIO_PIN_26 @ 0XFF180068</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_
    # clk- (TX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_26_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NA
    # ND chip enable)
		# PSU_IOU_SLCR_MIO_PIN_26_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[0]- (PMU
    #  GPI) 2= test_scan, Input, test_scan_in[26]- (Test Scan Port) = test_sca
    # n, Output, test_scan_out[26]- (Test Scan Port) 3= csu, Input, csu_ext_ta
    # mper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_26_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[0]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[0]- (GPIO bank 1) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= pjtag, Input, pjtag_tck- (PJTAG
    # TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_scl
    # k_out- (SPI Clock) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Inpu
    # t, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- (
    # Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_26_L3_SEL                                                  0

		# Configures MIO Pin 26 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180068, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180068 0x000000FE 0x00000000
		# Register : MIO_PIN_27 @ 0XFF18006C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd
    # [0]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_27_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (N
    # AND Ready/Busy)
		# PSU_IOU_SLCR_MIO_PIN_27_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[1]- (PMU
    #  GPI) 2= test_scan, Input, test_scan_in[27]- (Test Scan Port) = test_sca
    # n, Output, test_scan_out[27]- (Test Scan Port) 3= dpaux, Input, dp_aux_d
    # ata_in- (Dp Aux Data) = dpaux, Output, dp_aux_data_out- (Dp Aux Data)
		# PSU_IOU_SLCR_MIO_PIN_27_L2_SEL                                                  3

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[1]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[1]- (GPIO bank 1) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tdi- (PJTAG
    #  TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc2, O
    # utput, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UAR
    # T transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port D
    # atabus)
		# PSU_IOU_SLCR_MIO_PIN_27_L3_SEL                                                  0

		# Configures MIO Pin 27 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18006C, 0x000000FEU ,0x00000018U)  */
    mask_write 0XFF18006C 0x000000FE 0x00000018
		# Register : MIO_PIN_28 @ 0XFF180070</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd
    # [1]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_28_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (N
    # AND Ready/Busy)
		# PSU_IOU_SLCR_MIO_PIN_28_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[2]- (PMU
    #  GPI) 2= test_scan, Input, test_scan_in[28]- (Test Scan Port) = test_sca
    # n, Output, test_scan_out[28]- (Test Scan Port) 3= dpaux, Input, dp_hot_p
    # lug_detect- (Dp Aux Hot Plug)
		# PSU_IOU_SLCR_MIO_PIN_28_L2_SEL                                                  3

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[2]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[2]- (GPIO bank 1) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= pjtag, Output, pjtag_tdo- (PJTA
    # G TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc1,
    # Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitt
    # er serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_28_L3_SEL                                                  0

		# Configures MIO Pin 28 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180070, 0x000000FEU ,0x00000018U)  */
    mask_write 0XFF180070 0x000000FE 0x00000018
		# Register : MIO_PIN_29 @ 0XFF180074</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd
    # [2]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_29_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_29_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[3]- (PMU
    #  GPI) 2= test_scan, Input, test_scan_in[29]- (Test Scan Port) = test_sca
    # n, Output, test_scan_out[29]- (Test Scan Port) 3= dpaux, Input, dp_aux_d
    # ata_in- (Dp Aux Data) = dpaux, Output, dp_aux_data_out- (Dp Aux Data)
		# PSU_IOU_SLCR_MIO_PIN_29_L2_SEL                                                  3

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[3]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[3]- (GPIO bank 1) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tms- (PJTAG
    # TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output,
    #  spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out-
    # (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input
    # ) 7= trace, Output, tracedq[7]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_29_L3_SEL                                                  0

		# Configures MIO Pin 29 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180074, 0x000000FEU ,0x00000018U)  */
    mask_write 0XFF180074 0x000000FE 0x00000018
		# Register : MIO_PIN_30 @ 0XFF180078</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd
    # [3]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_30_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_30_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[4]- (PMU
    #  GPI) 2= test_scan, Input, test_scan_in[30]- (Test Scan Port) = test_sca
    # n, Output, test_scan_out[30]- (Test Scan Port) 3= dpaux, Input, dp_hot_p
    # lug_detect- (Dp Aux Hot Plug)
		# PSU_IOU_SLCR_MIO_PIN_30_L2_SEL                                                  3

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[4]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[4]- (GPIO bank 1) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (Wat
    # ch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0
    # , Output, spi0_so- (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock
    # ) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output,
    #  tracedq[8]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_30_L3_SEL                                                  0

		# Configures MIO Pin 30 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180078, 0x000000FEU ,0x00000018U)  */
    mask_write 0XFF180078 0x000000FE 0x00000018
		# Register : MIO_PIN_31 @ 0XFF18007C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_
    # ctl- (TX RGMII control)
		# PSU_IOU_SLCR_MIO_PIN_31_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_31_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[5]- (PMU
    #  GPI) 2= test_scan, Input, test_scan_in[31]- (Test Scan Port) = test_sca
    # n, Output, test_scan_out[31]- (Test Scan Port) 3= csu, Input, csu_ext_ta
    # mper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_31_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[5]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[5]- (GPIO bank 1) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out- (
    # Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4=
    #  spi0, Input, spi0_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TT
    # C Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial outp
    # ut) 7= trace, Output, tracedq[9]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_31_L3_SEL                                                  0

		# Configures MIO Pin 31 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18007C, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF18007C 0x000000FE 0x00000000
		# Register : MIO_PIN_32 @ 0XFF180080</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_c
    # lk- (RX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_32_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NA
    # ND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe)
		# PSU_IOU_SLCR_MIO_PIN_32_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[0]- (PM
    # U GPI) 2= test_scan, Input, test_scan_in[32]- (Test Scan Port) = test_sc
    # an, Output, test_scan_out[32]- (Test Scan Port) 3= csu, Input, csu_ext_t
    # amper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_32_L2_SEL                                                  1

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[6]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[6]- (GPIO bank 1) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (Wa
    # tch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4=
    # spi1, Output, spi1_sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (T
    # TC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= t
    # race, Output, tracedq[10]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_32_L3_SEL                                                  0

		# Configures MIO Pin 32 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180080, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180080 0x000000FE 0x00000008
		# Register : MIO_PIN_33 @ 0XFF180084</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[
    # 0]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_33_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_33_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[1]- (PM
    # U GPI) 2= test_scan, Input, test_scan_in[33]- (Test Scan Port) = test_sc
    # an, Output, test_scan_out[33]- (Test Scan Port) 3= csu, Input, csu_ext_t
    # amper- (CSU Ext Tamper)
		# PSU_IOU_SLCR_MIO_PIN_33_L2_SEL                                                  1

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[7]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[7]- (GPIO bank 1) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out- (W
    # atch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Mas
    # ter Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1
    # , Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, tracedq
    # [11]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_33_L3_SEL                                                  0

		# Configures MIO Pin 33 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180084, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180084 0x000000FE 0x00000008
		# Register : MIO_PIN_34 @ 0XFF180088</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[
    # 1]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_34_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_34_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[2]- (PM
    # U GPI) 2= test_scan, Input, test_scan_in[34]- (Test Scan Port) = test_sc
    # an, Output, test_scan_out[34]- (Test Scan Port) 3= dpaux, Input, dp_aux_
    # data_in- (Dp Aux Data) = dpaux, Output, dp_aux_data_out- (Dp Aux Data)
		# PSU_IOU_SLCR_MIO_PIN_34_L2_SEL                                                  1

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[8]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[8]- (GPIO bank 1) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (Wat
    # ch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master
    #  Selects) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rx
    # d- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace Po
    # rt Databus)
		# PSU_IOU_SLCR_MIO_PIN_34_L3_SEL                                                  0

		# Configures MIO Pin 34 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180088, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180088 0x000000FE 0x00000008
		# Register : MIO_PIN_35 @ 0XFF18008C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[
    # 2]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_35_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_35_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[3]- (PM
    # U GPI) 2= test_scan, Input, test_scan_in[35]- (Test Scan Port) = test_sc
    # an, Output, test_scan_out[35]- (Test Scan Port) 3= dpaux, Input, dp_hot_
    # plug_detect- (Dp Aux Hot Plug)
		# PSU_IOU_SLCR_MIO_PIN_35_L2_SEL                                                  1

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[9]- (GPIO bank 1) 0= g
    # pio1, Output, gpio_1_pin_out[9]- (GPIO bank 1) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out- (
    # Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master
    # Selects) 4= spi1, Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc2
    # , Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (
    # UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Po
    # rt Databus)
		# PSU_IOU_SLCR_MIO_PIN_35_L3_SEL                                                  0

		# Configures MIO Pin 35 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18008C, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF18008C 0x000000FE 0x00000008
		# Register : MIO_PIN_36 @ 0XFF180090</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[
    # 3]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_36_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_36_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[4]- (PM
    # U GPI) 2= test_scan, Input, test_scan_in[36]- (Test Scan Port) = test_sc
    # an, Output, test_scan_out[36]- (Test Scan Port) 3= dpaux, Input, dp_aux_
    # data_in- (Dp Aux Data) = dpaux, Output, dp_aux_data_out- (Dp Aux Data)
		# PSU_IOU_SLCR_MIO_PIN_36_L2_SEL                                                  1

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[10]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[10]- (GPIO bank 1) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= s
    # pi1, Output, spi1_so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Cl
    # ock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace,
    #  Output, tracedq[14]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_36_L3_SEL                                                  0

		# Configures MIO Pin 36 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180090, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180090 0x000000FE 0x00000008
		# Register : MIO_PIN_37 @ 0XFF180094</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_c
    # tl- (RX RGMII control )
		# PSU_IOU_SLCR_MIO_PIN_37_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (
    # PCIE Reset signal)
		# PSU_IOU_SLCR_MIO_PIN_37_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[5]- (PM
    # U GPI) 2= test_scan, Input, test_scan_in[37]- (Test Scan Port) = test_sc
    # an, Output, test_scan_out[37]- (Test Scan Port) 3= dpaux, Input, dp_hot_
    # plug_detect- (Dp Aux Hot Plug)
		# PSU_IOU_SLCR_MIO_PIN_37_L2_SEL                                                  1

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[11]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[11]- (GPIO bank 1) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4
    # = spi1, Input, spi1_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (T
    # TC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
    # 7= trace, Output, tracedq[15]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_37_L3_SEL                                                  0

		# Configures MIO Pin 37 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180094, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180094 0x000000FE 0x00000008
		# Register : MIO_PIN_38 @ 0XFF180098</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_
    # clk- (TX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_38_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_38_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out-
    # (SDSDIO clock) 2= Not Used 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_38_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[12]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[12]- (GPIO bank 1) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= pjtag, Input, pjtag_tck- (PJTA
    # G TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_s
    # clk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, In
    # put, ua0_rxd- (UART receiver serial input) 7= trace, Output, trace_clk-
    # (Trace Port Clock)
		# PSU_IOU_SLCR_MIO_PIN_38_L3_SEL                                                  0

		# Configures MIO Pin 38 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180098, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180098 0x000000FE 0x00000000
		# Register : MIO_PIN_39 @ 0XFF18009C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd
    # [0]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_39_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_39_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD
    # card detect from connector) 2= sd1, Input, sd1_data_in[4]- (8-bit Data b
    # us) = sd1, Output, sdio1_data_out[4]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_39_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[13]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[13]- (GPIO bank 1) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tdi- (PJT
    # AG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc0,
    #  Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (U
    # ART transmitter serial output) 7= trace, Output, trace_ctl- (Trace Port
    # Control Signal)
		# PSU_IOU_SLCR_MIO_PIN_39_L3_SEL                                                  0

		# Configures MIO Pin 39 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18009C, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF18009C 0x000000FE 0x00000010
		# Register : MIO_PIN_40 @ 0XFF1800A0</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd
    # [1]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_40_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_40_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Com
    # mand Indicator) = sd0, Output, sdio0_cmd_out- (Command Indicator) 2= sd1
    # , Input, sd1_data_in[5]- (8-bit Data bus) = sd1, Output, sdio1_data_out[
    # 5]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_40_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[14]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[14]- (GPIO bank 1) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= pjtag, Output, pjtag_tdo- (PJ
    # TAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc3
    # , Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmi
    # tter serial output) 7= trace, Output, tracedq[0]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_40_L3_SEL                                                  0

		# Configures MIO Pin 40 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800A0, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800A0 0x000000FE 0x00000010
		# Register : MIO_PIN_41 @ 0XFF1800A4</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd
    # [2]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_41_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_41_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[6]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[6]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_41_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[15]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[15]- (GPIO bank 1) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tms- (PJTA
    # G TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Outpu
    # t, spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out
    # - (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inp
    # ut) 7= trace, Output, tracedq[1]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_41_L3_SEL                                                  0

		# Configures MIO Pin 41 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800A4, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800A4 0x000000FE 0x00000010
		# Register : MIO_PIN_42 @ 0XFF1800A8</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd
    # [3]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_42_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_42_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[7]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[7]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_42_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[16]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[16]- (GPIO bank 1) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= sp
    # i0, Output, spi0_so- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clo
    # ck) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outpu
    # t, tracedq[2]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_42_L3_SEL                                                  0

		# Configures MIO Pin 42 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800A8, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800A8 0x000000FE 0x00000010
		# Register : MIO_PIN_43 @ 0XFF1800AC</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_
    # ctl- (TX RGMII control)
		# PSU_IOU_SLCR_MIO_PIN_43_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_43_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8-bit Data bus) 2= s
    # d1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_43_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[17]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[17]- (GPIO bank 1) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal)
    # 4= spi0, Input, spi0_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (
    # TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial ou
    # tput) 7= trace, Output, tracedq[3]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_43_L3_SEL                                                  0

		# Configures MIO Pin 43 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800AC, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF1800AC 0x000000FE 0x00000000
		# Register : MIO_PIN_44 @ 0XFF1800B0</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_c
    # lk- (RX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_44_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_44_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8-bit Data bus) 2= s
    # d1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_44_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[18]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[18]- (GPIO bank 1) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4
    # = spi1, Output, spi1_sclk_out- (SPI Clock) 5= ttc1, Input, ttc1_clk_in-
    # (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7=
    #  Not Used
		# PSU_IOU_SLCR_MIO_PIN_44_L3_SEL                                                  0

		# Configures MIO Pin 44 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800B0, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800B0 0x000000FE 0x00000010
		# Register : MIO_PIN_45 @ 0XFF1800B4</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[
    # 0]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_45_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_45_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8-bit Data bus) 2= s
    # d1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_45_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[19]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[19]- (GPIO bank 1) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI M
    # aster Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= u
    # a1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_45_L3_SEL                                                  0

		# Configures MIO Pin 45 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800B4, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800B4 0x000000FE 0x00000010
		# Register : MIO_PIN_46 @ 0XFF1800B8</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[
    # 1]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_46_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_46_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[0]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_46_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[20]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[20]- (GPIO bank 1) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Mast
    # er Selects) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_
    # rxd- (UART receiver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_46_L3_SEL                                                  0

		# Configures MIO Pin 46 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800B8, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800B8 0x000000FE 0x00000010
		# Register : MIO_PIN_47 @ 0XFF1800BC</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[
    # 2]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_47_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_47_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[1]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_47_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[21]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[21]- (GPIO bank 1) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Maste
    # r Selects) 4= spi1, Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= tt
    # c0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd-
    #  (UART transmitter serial output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_47_L3_SEL                                                  0

		# Configures MIO Pin 47 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800BC, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800BC 0x000000FE 0x00000010
		# Register : MIO_PIN_48 @ 0XFF1800C0</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[
    # 3]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_48_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_48_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[2]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_48_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[22]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[22]- (GPIO bank 1) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= s
    # pi1, Output, spi1_so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Cl
    # ock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Us
    # ed
		# PSU_IOU_SLCR_MIO_PIN_48_L3_SEL                                                  0

		# Configures MIO Pin 48 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800C0, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800C0 0x000000FE 0x00000010
		# Register : MIO_PIN_49 @ 0XFF1800C4</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_c
    # tl- (RX RGMII control )
		# PSU_IOU_SLCR_MIO_PIN_49_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_49_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow-
    # (SD card bus power) 2= sd1, Input, sd1_data_in[3]- (8-bit Data bus) = sd
    # 1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_49_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[23]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[23]- (GPIO bank 1) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4
    # = spi1, Input, spi1_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (T
    # TC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
    # 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_49_L3_SEL                                                  0

		# Configures MIO Pin 49 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800C4, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800C4 0x000000FE 0x00000010
		# Register : MIO_PIN_50 @ 0XFF1800C8</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk-
    #  (TSU clock)
		# PSU_IOU_SLCR_MIO_PIN_50_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_50_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD ca
    # rd write protect from connector) 2= sd1, Input, sd1_cmd_in- (Command Ind
    # icator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_50_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[24]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[24]- (GPIO bank 1) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5=
    # ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART rece
    # iver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_50_L3_SEL                                                  0

		# Configures MIO Pin 50 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800C8, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800C8 0x000000FE 0x00000010
		# Register : MIO_PIN_51 @ 0XFF1800CC</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk-
    #  (TSU clock)
		# PSU_IOU_SLCR_MIO_PIN_51_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_51_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Output, sdi
    # o1_clk_out- (SDSDIO clock) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_51_L2_SEL                                                  2

		# Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[25]- (GPIO bank 1) 0=
    # gpio1, Output, gpio_1_pin_out[25]- (GPIO bank 1) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= mdio1, Input, gem1_mdio_in- (MDIO Dat
    # a) 4= mdio1, Output, gem1_mdio_out- (MDIO Data) 5= ttc2, Output, ttc2_wa
    # ve_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter
    # serial output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_51_L3_SEL                                                  0

		# Configures MIO Pin 51 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800CC, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800CC 0x000000FE 0x00000010
		# Register : MIO_PIN_52 @ 0XFF1800D0</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_
    # clk- (TX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_52_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_clk_i
    # n- (ULPI Clock)
		# PSU_IOU_SLCR_MIO_PIN_52_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_52_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[0]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[0]- (GPIO bank 2) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= pjtag, Input, pjtag_tck- (PJTAG
    #  TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sc
    # lk_out- (SPI Clock) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Out
    # put, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_c
    # lk- (Trace Port Clock)
		# PSU_IOU_SLCR_MIO_PIN_52_L3_SEL                                                  0

		# Configures MIO Pin 52 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800D0, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800D0 0x000000FE 0x00000004
		# Register : MIO_PIN_53 @ 0XFF1800D4</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd
    # [0]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_53_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_dir-
    # (Data bus direction control)
		# PSU_IOU_SLCR_MIO_PIN_53_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_53_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[1]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[1]- (GPIO bank 2) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tdi- (PJTAG
    # TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Ou
    # tput, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART
    # receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control
    # Signal)
		# PSU_IOU_SLCR_MIO_PIN_53_L3_SEL                                                  0

		# Configures MIO Pin 53 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800D4, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800D4 0x000000FE 0x00000004
		# Register : MIO_PIN_54 @ 0XFF1800D8</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd
    # [1]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_54_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[2]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[2]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_54_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_54_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[2]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[2]- (GPIO bank 2) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= pjtag, Output, pjtag_tdo- (PJTAG
    #  TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, I
    # nput, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver se
    # rial input) 7= trace, Output, tracedq[0]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_54_L3_SEL                                                  0

		# Configures MIO Pin 54 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800D8, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800D8 0x000000FE 0x00000004
		# Register : MIO_PIN_55 @ 0XFF1800DC</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd
    # [2]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_55_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_nxt-
    # (Data flow control signal from the PHY)
		# PSU_IOU_SLCR_MIO_PIN_55_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_55_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[3]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[3]- (GPIO bank 2) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tms- (PJTAG
    #  TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output
    # , spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out-
    #  (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial
    # output) 7= trace, Output, tracedq[1]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_55_L3_SEL                                                  0

		# Configures MIO Pin 55 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800DC, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800DC 0x000000FE 0x00000004
		# Register : MIO_PIN_56 @ 0XFF1800E0</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd
    # [3]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_56_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[0]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[0]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_56_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_56_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[4]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[4]- (GPIO bank 2) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (Wa
    # tch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi
    # 0, Output, spi0_so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Cloc
    # k) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, O
    # utput, tracedq[2]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_56_L3_SEL                                                  0

		# Configures MIO Pin 56 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800E0, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800E0 0x000000FE 0x00000004
		# Register : MIO_PIN_57 @ 0XFF1800E4</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_
    # ctl- (TX RGMII control)
		# PSU_IOU_SLCR_MIO_PIN_57_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[1]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[1]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_57_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_57_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[5]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[5]- (GPIO bank 2) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out- (W
    # atch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4=
    # spi0, Input, spi0_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC
    #  Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7=
    #  trace, Output, tracedq[3]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_57_L3_SEL                                                  0

		# Configures MIO Pin 57 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800E4, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800E4 0x000000FE 0x00000004
		# Register : MIO_PIN_58 @ 0XFF1800E8</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_c
    # lk- (RX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_58_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Output, usb0_ulpi_stp-
    #  (Asserted to end or interrupt transfers)
		# PSU_IOU_SLCR_MIO_PIN_58_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_58_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[6]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[6]- (GPIO bank 2) 1= can0, Input, can0_phy_
    # rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0
    # , Output, i2c0_scl_out- (SCL signal) 3= pjtag, Input, pjtag_tck- (PJTAG
    # TCK) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1_scl
    # k_out- (SPI Clock) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Inpu
    # t, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- (
    # Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_58_L3_SEL                                                  0

		# Configures MIO Pin 58 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800E8, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800E8 0x000000FE 0x00000004
		# Register : MIO_PIN_59 @ 0XFF1800EC</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[
    # 0]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_59_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[3]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[3]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_59_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_59_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[7]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[7]- (GPIO bank 2) 1= can0, Output, can0_phy
    # _tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c
    # 0, Output, i2c0_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tdi- (PJTAG
    #  TDI) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= ttc2, O
    # utput, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UAR
    # T transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port D
    # atabus)
		# PSU_IOU_SLCR_MIO_PIN_59_L3_SEL                                                  0

		# Configures MIO Pin 59 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800EC, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800EC 0x000000FE 0x00000004
		# Register : MIO_PIN_60 @ 0XFF1800F0</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[
    # 1]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_60_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[4]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[4]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_60_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_60_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[8]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[8]- (GPIO bank 2) 1= can1, Output, can1_phy
    # _tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c
    # 1, Output, i2c1_scl_out- (SCL signal) 3= pjtag, Output, pjtag_tdo- (PJTA
    # G TDO) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc1,
    # Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitt
    # er serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_60_L3_SEL                                                  0

		# Configures MIO Pin 60 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800F0, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800F0 0x000000FE 0x00000004
		# Register : MIO_PIN_61 @ 0XFF1800F4</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[
    # 2]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_61_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[5]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[5]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_61_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_61_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[9]- (GPIO bank 2) 0= g
    # pio2, Output, gpio_2_pin_out[9]- (GPIO bank 2) 1= can1, Input, can1_phy_
    # rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1
    # , Output, i2c1_sda_out- (SDA signal) 3= pjtag, Input, pjtag_tms- (PJTAG
    # TMS) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, Output,
    #  spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out-
    # (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input
    # ) 7= trace, Output, tracedq[7]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_61_L3_SEL                                                  0

		# Configures MIO Pin 61 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800F4, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800F4 0x000000FE 0x00000004
		# Register : MIO_PIN_62 @ 0XFF1800F8</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[
    # 3]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_62_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[6]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[6]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_62_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_62_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[10]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[10]- (GPIO bank 2) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= sp
    # i1, Output, spi1_so- (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clo
    # ck) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outpu
    # t, tracedq[8]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_62_L3_SEL                                                  0

		# Configures MIO Pin 62 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800F8, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800F8 0x000000FE 0x00000004
		# Register : MIO_PIN_63 @ 0XFF1800FC</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_c
    # tl- (RX RGMII control )
		# PSU_IOU_SLCR_MIO_PIN_63_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_da
    # ta[7]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_data[7]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_63_L1_SEL                                                  1

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not
    # Used
		# PSU_IOU_SLCR_MIO_PIN_63_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[11]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[11]- (GPIO bank 2) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal)
    # 4= spi1, Input, spi1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (
    # TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial ou
    # tput) 7= trace, Output, tracedq[9]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_63_L3_SEL                                                  0

		# Configures MIO Pin 63 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF1800FC, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800FC 0x000000FE 0x00000004
		# Register : MIO_PIN_64 @ 0XFF180100</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_
    # clk- (TX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_64_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_clk_i
    # n- (ULPI Clock)
		# PSU_IOU_SLCR_MIO_PIN_64_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out-
    # (SDSDIO clock) 2= Not Used 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_64_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[12]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[12]- (GPIO bank 2) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4
    # = spi0, Output, spi0_sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in-
    # (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7=
    #  trace, Output, tracedq[10]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_64_L3_SEL                                                  0

		# Configures MIO Pin 64 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180100, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180100 0x000000FE 0x00000002
		# Register : MIO_PIN_65 @ 0XFF180104</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd
    # [0]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_65_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_dir-
    # (Data bus direction control)
		# PSU_IOU_SLCR_MIO_PIN_65_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD
    # card detect from connector) 2= Not Used 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_65_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[13]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[13]- (GPIO bank 2) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi0, Output, spi0_n_ss_out[2]- (SPI M
    # aster Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= u
    # a1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace
    # dq[11]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_65_L3_SEL                                                  0

		# Configures MIO Pin 65 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180104, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180104 0x000000FE 0x00000002
		# Register : MIO_PIN_66 @ 0XFF180108</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd
    # [1]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_66_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[2]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[2]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_66_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Com
    # mand Indicator) = sd0, Output, sdio0_cmd_out- (Command Indicator) 2= Not
    #  Used 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_66_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[14]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[14]- (GPIO bank 2) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Mast
    # er Selects) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_
    # rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace
    # Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_66_L3_SEL                                                  0

		# Configures MIO Pin 66 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180108, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180108 0x000000FE 0x00000002
		# Register : MIO_PIN_67 @ 0XFF18010C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd
    # [2]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_67_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_nxt-
    # (Data flow control signal from the PHY)
		# PSU_IOU_SLCR_MIO_PIN_67_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8-bit Data bus) 2= N
    # ot Used 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_67_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[15]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[15]- (GPIO bank 2) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi0, Input, spi0_n_ss_in- (SPI Maste
    # r Selects) 4= spi0, Output, spi0_n_ss_out[0]- (SPI Master Selects) 5= tt
    # c2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd-
    #  (UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace
    # Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_67_L3_SEL                                                  0

		# Configures MIO Pin 67 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18010C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18010C 0x000000FE 0x00000002
		# Register : MIO_PIN_68 @ 0XFF180110</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd
    # [3]- (TX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_68_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[0]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[0]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_68_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8-bit Data bus) 2= N
    # ot Used 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_68_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[16]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[16]- (GPIO bank 2) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= s
    # pi0, Output, spi0_so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Cl
    # ock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace,
    #  Output, tracedq[14]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_68_L3_SEL                                                  0

		# Configures MIO Pin 68 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180110, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180110 0x000000FE 0x00000002
		# Register : MIO_PIN_69 @ 0XFF180114</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_
    # ctl- (TX RGMII control)
		# PSU_IOU_SLCR_MIO_PIN_69_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[1]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[1]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_69_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8-bit Data bus) 2= s
    # d1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_69_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[17]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[17]- (GPIO bank 2) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4
    # = spi0, Input, spi0_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (T
    # TC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
    # 7= trace, Output, tracedq[15]- (Trace Port Databus)
		# PSU_IOU_SLCR_MIO_PIN_69_L3_SEL                                                  0

		# Configures MIO Pin 69 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180114, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180114 0x000000FE 0x00000002
		# Register : MIO_PIN_70 @ 0XFF180118</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_c
    # lk- (RX RGMII clock)
		# PSU_IOU_SLCR_MIO_PIN_70_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Output, usb1_ulpi_stp-
    #  (Asserted to end or interrupt transfers)
		# PSU_IOU_SLCR_MIO_PIN_70_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8-bit Data bus) 2= s
    # d1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_70_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[18]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[18]- (GPIO bank 2) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4=
    #  spi1, Output, spi1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (
    # TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not U
    # sed
		# PSU_IOU_SLCR_MIO_PIN_70_L3_SEL                                                  0

		# Configures MIO Pin 70 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180118, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180118 0x000000FE 0x00000002
		# Register : MIO_PIN_71 @ 0XFF18011C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[
    # 0]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_71_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[3]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[3]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_71_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[0]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_71_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[19]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[19]- (GPIO bank 2) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI
    # Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6=
    # ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_71_L3_SEL                                                  0

		# Configures MIO Pin 71 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18011C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18011C 0x000000FE 0x00000002
		# Register : MIO_PIN_72 @ 0XFF180120</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[
    # 1]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_72_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[4]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[4]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_72_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[1]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_72_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[20]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[20]- (GPIO bank 2) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= swdt1, Input, swdt1_clk_in- (
    # Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Mas
    # ter Selects) 5= Not Used 6= ua1, Output, ua1_txd- (UART transmitter seri
    # al output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_72_L3_SEL                                                  0

		# Configures MIO Pin 72 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180120, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180120 0x000000FE 0x00000002
		# Register : MIO_PIN_73 @ 0XFF180124</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[
    # 2]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_73_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[5]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[5]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_73_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[2]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_73_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[21]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[21]- (GPIO bank 2) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= swdt1, Output, swdt1_rst_out-
    # (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master
    #  Selects) 4= spi1, Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= Not
    #  Used 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_73_L3_SEL                                                  0

		# Configures MIO Pin 73 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180124, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180124 0x000000FE 0x00000002
		# Register : MIO_PIN_74 @ 0XFF180128</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[
    # 3]- (RX RGMII data)
		# PSU_IOU_SLCR_MIO_PIN_74_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[6]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[6]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_74_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]-
    # (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8-bit Data bus) 2= s
    # d1, Input, sd1_data_in[3]- (8-bit Data bus) = sd1, Output, sdio1_data_ou
    # t[3]- (8-bit Data bus) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_74_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[22]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[22]- (GPIO bank 2) 1= can0, Input, can0_ph
    # y_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2
    # c0, Output, i2c0_scl_out- (SCL signal) 3= swdt0, Input, swdt0_clk_in- (W
    # atch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= sp
    # i1, Output, spi1_so- (MISO signal) 5= Not Used 6= ua0, Input, ua0_rxd- (
    # UART receiver serial input) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_74_L3_SEL                                                  0

		# Configures MIO Pin 74 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180128, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180128 0x000000FE 0x00000002
		# Register : MIO_PIN_75 @ 0XFF18012C</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_c
    # tl- (RX RGMII control )
		# PSU_IOU_SLCR_MIO_PIN_75_L0_SEL                                                  1

		# Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_da
    # ta[7]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_data[7]- (ULPI data
    #  bus)
		# PSU_IOU_SLCR_MIO_PIN_75_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow-
    # (SD card bus power) 2= sd1, Input, sd1_cmd_in- (Command Indicator) = sd1
    # , Output, sdio1_cmd_out- (Command Indicator) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_75_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[23]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[23]- (GPIO bank 2) 1= can0, Output, can0_p
    # hy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i
    # 2c0, Output, i2c0_sda_out- (SDA signal) 3= swdt0, Output, swdt0_rst_out-
    #  (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal)
    # 4= spi1, Input, spi1_si- (MOSI signal) 5= Not Used 6= ua0, Output, ua0_t
    # xd- (UART transmitter serial output) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_75_L3_SEL                                                  0

		# Configures MIO Pin 75 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF18012C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18012C 0x000000FE 0x00000002
		# Register : MIO_PIN_76 @ 0XFF180130</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_76_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_76_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD ca
    # rd write protect from connector) 2= sd1, Output, sdio1_clk_out- (SDSDIO
    # clock) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_76_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[24]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[24]- (GPIO bank 2) 1= can1, Output, can1_p
    # hy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i
    # 2c1, Output, i2c1_scl_out- (SCL signal) 3= mdio0, Output, gem0_mdc- (MDI
    # O Clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= mdio2, Output, gem2
    # _mdc- (MDIO Clock) 6= mdio3, Output, gem3_mdc- (MDIO Clock) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_76_L3_SEL                                                  6

		# Configures MIO Pin 76 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180130, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180130 0x000000FE 0x000000C0
		# Register : MIO_PIN_77 @ 0XFF180134</p>

		# Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_77_L0_SEL                                                  0

		# Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
		# PSU_IOU_SLCR_MIO_PIN_77_L1_SEL                                                  0

		# Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Input, sdio
    # 1_cd_n- (SD card detect from connector) 3= Not Used
		# PSU_IOU_SLCR_MIO_PIN_77_L2_SEL                                                  0

		# Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[25]- (GPIO bank 2) 0=
    # gpio2, Output, gpio_2_pin_out[25]- (GPIO bank 2) 1= can1, Input, can1_ph
    # y_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2
    # c1, Output, i2c1_sda_out- (SDA signal) 3= mdio0, Input, gem0_mdio_in- (M
    # DIO Data) 3= mdio0, Output, gem0_mdio_out- (MDIO Data) 4= mdio1, Input,
    # gem1_mdio_in- (MDIO Data) 4= mdio1, Output, gem1_mdio_out- (MDIO Data) 5
    # = mdio2, Input, gem2_mdio_in- (MDIO Data) 5= mdio2, Output, gem2_mdio_ou
    # t- (MDIO Data) 6= mdio3, Input, gem3_mdio_in- (MDIO Data) 6= mdio3, Outp
    # ut, gem3_mdio_out- (MDIO Data) 7= Not Used
		# PSU_IOU_SLCR_MIO_PIN_77_L3_SEL                                                  6

		# Configures MIO Pin 77 peripheral interface mapping
		#(OFFSET, MASK, VALUE)      (0XFF180134, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180134 0x000000FE 0x000000C0
		# Register : MIO_MST_TRI0 @ 0XFF180204</p>

		# Master Tri-state Enable for pin 0, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI                                            0

		# Master Tri-state Enable for pin 1, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI                                            0

		# Master Tri-state Enable for pin 2, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI                                            0

		# Master Tri-state Enable for pin 3, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI                                            0

		# Master Tri-state Enable for pin 4, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI                                            0

		# Master Tri-state Enable for pin 5, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI                                            0

		# Master Tri-state Enable for pin 6, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI                                            0

		# Master Tri-state Enable for pin 7, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI                                            0

		# Master Tri-state Enable for pin 8, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI                                            0

		# Master Tri-state Enable for pin 9, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI                                            0

		# Master Tri-state Enable for pin 10, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI                                            0

		# Master Tri-state Enable for pin 11, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI                                            0

		# Master Tri-state Enable for pin 12, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI                                            0

		# Master Tri-state Enable for pin 13, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI                                            0

		# Master Tri-state Enable for pin 14, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI                                            0

		# Master Tri-state Enable for pin 15, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI                                            0

		# Master Tri-state Enable for pin 16, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI                                            0

		# Master Tri-state Enable for pin 17, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI                                            0

		# Master Tri-state Enable for pin 18, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI                                            1

		# Master Tri-state Enable for pin 19, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI                                            0

		# Master Tri-state Enable for pin 20, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI                                            0

		# Master Tri-state Enable for pin 21, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI                                            1

		# Master Tri-state Enable for pin 22, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI                                            0

		# Master Tri-state Enable for pin 23, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI                                            0

		# Master Tri-state Enable for pin 24, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI                                            0

		# Master Tri-state Enable for pin 25, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI                                            1

		# Master Tri-state Enable for pin 26, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI                                            0

		# Master Tri-state Enable for pin 27, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI                                            0

		# Master Tri-state Enable for pin 28, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI                                            1

		# Master Tri-state Enable for pin 29, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI                                            0

		# Master Tri-state Enable for pin 30, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI                                            1

		# Master Tri-state Enable for pin 31, active high
		# PSU_IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI                                            0

		# MIO pin Tri-state Enables, 31:0
		#(OFFSET, MASK, VALUE)      (0XFF180204, 0xFFFFFFFFU ,0x52240000U)  */
    mask_write 0XFF180204 0xFFFFFFFF 0x52240000
		# Register : MIO_MST_TRI1 @ 0XFF180208</p>

		# Master Tri-state Enable for pin 32, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI                                            0

		# Master Tri-state Enable for pin 33, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI                                            0

		# Master Tri-state Enable for pin 34, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI                                            0

		# Master Tri-state Enable for pin 35, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI                                            0

		# Master Tri-state Enable for pin 36, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI                                            0

		# Master Tri-state Enable for pin 37, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI                                            0

		# Master Tri-state Enable for pin 38, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI                                            0

		# Master Tri-state Enable for pin 39, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI                                            0

		# Master Tri-state Enable for pin 40, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI                                            0

		# Master Tri-state Enable for pin 41, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI                                            0

		# Master Tri-state Enable for pin 42, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI                                            0

		# Master Tri-state Enable for pin 43, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI                                            0

		# Master Tri-state Enable for pin 44, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI                                            1

		# Master Tri-state Enable for pin 45, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI                                            1

		# Master Tri-state Enable for pin 46, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI                                            0

		# Master Tri-state Enable for pin 47, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI                                            0

		# Master Tri-state Enable for pin 48, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI                                            0

		# Master Tri-state Enable for pin 49, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI                                            0

		# Master Tri-state Enable for pin 50, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI                                            0

		# Master Tri-state Enable for pin 51, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI                                            0

		# Master Tri-state Enable for pin 52, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI                                            1

		# Master Tri-state Enable for pin 53, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI                                            1

		# Master Tri-state Enable for pin 54, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI                                            0

		# Master Tri-state Enable for pin 55, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI                                            1

		# Master Tri-state Enable for pin 56, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI                                            0

		# Master Tri-state Enable for pin 57, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI                                            0

		# Master Tri-state Enable for pin 58, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI                                            0

		# Master Tri-state Enable for pin 59, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI                                            0

		# Master Tri-state Enable for pin 60, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI                                            0

		# Master Tri-state Enable for pin 61, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI                                            0

		# Master Tri-state Enable for pin 62, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI                                            0

		# Master Tri-state Enable for pin 63, active high
		# PSU_IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI                                            0

		# MIO pin Tri-state Enables, 63:32
		#(OFFSET, MASK, VALUE)      (0XFF180208, 0xFFFFFFFFU ,0x00B03000U)  */
    mask_write 0XFF180208 0xFFFFFFFF 0x00B03000
		# Register : MIO_MST_TRI2 @ 0XFF18020C</p>

		# Master Tri-state Enable for pin 64, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI                                            0

		# Master Tri-state Enable for pin 65, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI                                            0

		# Master Tri-state Enable for pin 66, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI                                            0

		# Master Tri-state Enable for pin 67, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI                                            0

		# Master Tri-state Enable for pin 68, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI                                            0

		# Master Tri-state Enable for pin 69, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI                                            0

		# Master Tri-state Enable for pin 70, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI                                            1

		# Master Tri-state Enable for pin 71, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI                                            1

		# Master Tri-state Enable for pin 72, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI                                            1

		# Master Tri-state Enable for pin 73, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI                                            1

		# Master Tri-state Enable for pin 74, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI                                            1

		# Master Tri-state Enable for pin 75, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI                                            1

		# Master Tri-state Enable for pin 76, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI                                            0

		# Master Tri-state Enable for pin 77, active high
		# PSU_IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI                                            0

		# MIO pin Tri-state Enables, 77:64
		#(OFFSET, MASK, VALUE)      (0XFF18020C, 0x00003FFFU ,0x00000FC0U)  */
    mask_write 0XFF18020C 0x00003FFF 0x00000FC0
		# Register : bank0_ctrl0 @ 0XFF180138</p>

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25                                          1

		# Drive0 control to MIO Bank 0 - control MIO[25:0]
		#(OFFSET, MASK, VALUE)      (0XFF180138, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180138 0x03FFFFFF 0x03FFFFFF
		# Register : bank0_ctrl1 @ 0XFF18013C</p>

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25                                          1

		# Drive1 control to MIO Bank 0 - control MIO[25:0]
		#(OFFSET, MASK, VALUE)      (0XFF18013C, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF18013C 0x03FFFFFF 0x03FFFFFF
		# Register : bank0_ctrl3 @ 0XFF180140</p>

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25                                  0

		# Selects either Schmitt or CMOS input for MIO Bank 0 - control MIO[25:0]
		#(OFFSET, MASK, VALUE)      (0XFF180140, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180140 0x03FFFFFF 0x00000000
		# Register : bank0_ctrl4 @ 0XFF180144</p>

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25                                 1

		# When mio_bank0_pull_enable is set, this selects pull up or pull down for
    #  MIO Bank 0 - control MIO[25:0]
		#(OFFSET, MASK, VALUE)      (0XFF180144, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180144 0x03FFFFFF 0x03FFFFFF
		# Register : bank0_ctrl5 @ 0XFF180148</p>

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25                                     1

		# When set, this enables mio_bank0_pullupdown to selects pull up or pull d
    # own for MIO Bank 0 - control MIO[25:0]
		#(OFFSET, MASK, VALUE)      (0XFF180148, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180148 0x03FFFFFF 0x03FFFFFF
		# Register : bank0_ctrl6 @ 0XFF18014C</p>

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24                                0

		# Each bit applies to a single IO. Bit 0 for MIO[0].
		# PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25                                0

		# Slew rate control to MIO Bank 0 - control MIO[25:0]
		#(OFFSET, MASK, VALUE)      (0XFF18014C, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF18014C 0x03FFFFFF 0x00000000
		# Register : bank1_ctrl0 @ 0XFF180154</p>

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25                                          1

		# Drive0 control to MIO Bank 1 - control MIO[51:26]
		#(OFFSET, MASK, VALUE)      (0XFF180154, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180154 0x03FFFFFF 0x03FFFFFF
		# Register : bank1_ctrl1 @ 0XFF180158</p>

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25                                          1

		# Drive1 control to MIO Bank 1 - control MIO[51:26]
		#(OFFSET, MASK, VALUE)      (0XFF180158, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180158 0x03FFFFFF 0x03FFFFFF
		# Register : bank1_ctrl3 @ 0XFF18015C</p>

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25                                  0

		# Selects either Schmitt or CMOS input for MIO Bank 1 - control MIO[51:26]
		#(OFFSET, MASK, VALUE)      (0XFF18015C, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF18015C 0x03FFFFFF 0x00000000
		# Register : bank1_ctrl4 @ 0XFF180160</p>

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25                                 1

		# When mio_bank1_pull_enable is set, this selects pull up or pull down for
    #  MIO Bank 1 - control MIO[51:26]
		#(OFFSET, MASK, VALUE)      (0XFF180160, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180160 0x03FFFFFF 0x03FFFFFF
		# Register : bank1_ctrl5 @ 0XFF180164</p>

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25                                     1

		# When set, this enables mio_bank1_pullupdown to selects pull up or pull d
    # own for MIO Bank 1 - control MIO[51:26]
		#(OFFSET, MASK, VALUE)      (0XFF180164, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180164 0x03FFFFFF 0x03FFFFFF
		# Register : bank1_ctrl6 @ 0XFF180168</p>

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24                                0

		# Each bit applies to a single IO. Bit 0 for MIO[26].
		# PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25                                0

		# Slew rate control to MIO Bank 1 - control MIO[51:26]
		#(OFFSET, MASK, VALUE)      (0XFF180168, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180168 0x03FFFFFF 0x00000000
		# Register : bank2_ctrl0 @ 0XFF180170</p>

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25                                          1

		# Drive0 control to MIO Bank 2 - control MIO[77:52]
		#(OFFSET, MASK, VALUE)      (0XFF180170, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180170 0x03FFFFFF 0x03FFFFFF
		# Register : bank2_ctrl1 @ 0XFF180174</p>

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9                                           1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24                                          1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25                                          1

		# Drive1 control to MIO Bank 2 - control MIO[77:52]
		#(OFFSET, MASK, VALUE)      (0XFF180174, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180174 0x03FFFFFF 0x03FFFFFF
		# Register : bank2_ctrl3 @ 0XFF180178</p>

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9                                   0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24                                  0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25                                  0

		# Selects either Schmitt or CMOS input for MIO Bank 2 - control MIO[77:52]
		#(OFFSET, MASK, VALUE)      (0XFF180178, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180178 0x03FFFFFF 0x00000000
		# Register : bank2_ctrl4 @ 0XFF18017C</p>

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9                                  1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24                                 1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25                                 1

		# When mio_bank2_pull_enable is set, this selects pull up or pull down for
    #  MIO Bank 2 - control MIO[77:52]
		#(OFFSET, MASK, VALUE)      (0XFF18017C, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF18017C 0x03FFFFFF 0x03FFFFFF
		# Register : bank2_ctrl5 @ 0XFF180180</p>

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9                                      1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24                                     1

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25                                     1

		# When set, this enables mio_bank2_pullupdown to selects pull up or pull d
    # own for MIO Bank 2 - control MIO[77:52]
		#(OFFSET, MASK, VALUE)      (0XFF180180, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180180 0x03FFFFFF 0x03FFFFFF
		# Register : bank2_ctrl6 @ 0XFF180184</p>

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9                                 0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24                                0

		# Each bit applies to a single IO. Bit 0 for MIO[52].
		# PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25                                0

		# Slew rate control to MIO Bank 2 - control MIO[77:52]
		#(OFFSET, MASK, VALUE)      (0XFF180184, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180184 0x03FFFFFF 0x00000000
		# : LOOPBACK
		# Register : MIO_LOOPBACK @ 0XFF180200</p>

		# I2C Loopback Control. 0 = Connect I2C inputs according to MIO mapping. 1
    #  = Loop I2C 0 outputs to I2C 1 inputs, and I2C 1 outputs to I2C 0 inputs
    # .
		# PSU_IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1                                        0

		# CAN Loopback Control. 0 = Connect CAN inputs according to MIO mapping. 1
    #  = Loop CAN 0 Tx to CAN 1 Rx, and CAN 1 Tx to CAN 0 Rx.
		# PSU_IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1                                        0

		# UART Loopback Control. 0 = Connect UART inputs according to MIO mapping.
    #  1 = Loop UART 0 outputs to UART 1 inputs, and UART 1 outputs to UART 0
    # inputs. RXD/TXD cross-connected. RTS/CTS cross-connected. DSR, DTR, DCD
    # and RI not used.
		# PSU_IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1                                          0

		# SPI Loopback Control. 0 = Connect SPI inputs according to MIO mapping. 1
    #  = Loop SPI 0 outputs to SPI 1 inputs, and SPI 1 outputs to SPI 0 inputs
    # . The other SPI core will appear on the LS Slave Select.
		# PSU_IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1                                        0

		# Loopback function within MIO
		#(OFFSET, MASK, VALUE)      (0XFF180200, 0x0000000FU ,0x00000000U)  */
    mask_write 0XFF180200 0x0000000F 0x00000000
}

set psu_peripherals_init_data {
		# : COHERENCY
		# : FPD RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# PCIE config reset
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_CFG_RESET                                          0

		# PCIE control block level reset
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_CTRL_RESET                                         0

		# PCIE bridge block level reset (AXI interface)
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_BRIDGE_RESET                                       0

		# Display Port block level reset (includes DPDMA)
		# PSU_CRF_APB_RST_FPD_TOP_DP_RESET                                                0

		# FPD WDT reset
		# PSU_CRF_APB_RST_FPD_TOP_SWDT_RESET                                              0

		# GDMA block level reset
		# PSU_CRF_APB_RST_FPD_TOP_GDMA_RESET                                              0

		# Pixel Processor (submodule of GPU) block level reset
		# PSU_CRF_APB_RST_FPD_TOP_GPU_PP0_RESET                                           0

		# Pixel Processor (submodule of GPU) block level reset
		# PSU_CRF_APB_RST_FPD_TOP_GPU_PP1_RESET                                           0

		# GPU block level reset
		# PSU_CRF_APB_RST_FPD_TOP_GPU_RESET                                               0

		# GT block level reset
		# PSU_CRF_APB_RST_FPD_TOP_GT_RESET                                                0

		# Sata block level reset
		# PSU_CRF_APB_RST_FPD_TOP_SATA_RESET                                              0

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x000F807EU ,0x00000000U)  */
    mask_write 0XFD1A0100 0x000F807E 0x00000000
		# : RESET BLOCKS
		# : TIMESTAMP
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET                                        0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_IOU_CC_RESET                                           0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_ADMA_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x001A0000U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x001A0000 0x00000000
		# Register : RST_LPD_TOP @ 0XFF5E023C</p>

		# Reset entire full power domain.
		# PSU_CRL_APB_RST_LPD_TOP_FPD_RESET                                               0

		# LPD SWDT
		# PSU_CRL_APB_RST_LPD_TOP_LPD_SWDT_RESET                                          0

		# Sysmonitor reset
		# PSU_CRL_APB_RST_LPD_TOP_SYSMON_RESET                                            0

		# Real Time Clock reset
		# PSU_CRL_APB_RST_LPD_TOP_RTC_RESET                                               0

		# APM reset
		# PSU_CRL_APB_RST_LPD_TOP_APM_RESET                                               0

		# IPI reset
		# PSU_CRL_APB_RST_LPD_TOP_IPI_RESET                                               0

		# reset entire RPU power island
		# PSU_CRL_APB_RST_LPD_TOP_RPU_PGE_RESET                                           0

		# reset ocm
		# PSU_CRL_APB_RST_LPD_TOP_OCM_RESET                                               0

		# Software control register for the LPD block.
		#(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x0093C018U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x0093C018 0x00000000
		# : ENET
		# Register : RST_LPD_IOU0 @ 0XFF5E0230</p>

		# GEM 3 reset
		# PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET                                             0

		# Software controlled reset for the GEMs
		#(OFFSET, MASK, VALUE)      (0XFF5E0230, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0230 0x00000008 0x00000000
		# : QSPI
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_QSPI_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000001 0x00000000
		# : QSPI TAP DELAY
		# Register : IOU_TAPDLY_BYPASS @ 0XFF180390</p>

		# 0: Do not by pass the tap delays on the Rx clock signal of LQSPI 1: Bypa
    # ss the Tap delay on the Rx clock signal of LQSPI
		# PSU_IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX                                         1

		# IOU tap delay bypass for the LQSPI and NAND controllers
		#(OFFSET, MASK, VALUE)      (0XFF180390, 0x00000004U ,0x00000004U)  */
    mask_write 0XFF180390 0x00000004 0x00000004
		# : NAND
		# : USB
		# Register : RST_LPD_TOP @ 0XFF5E023C</p>

		# USB 0 reset for control registers
		# PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET                                          0

		# USB 0 sleep circuit reset
		# PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET                                         0

		# USB 0 reset
		# PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET                                          0

		# Software control register for the LPD block.
		#(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000540U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00000540 0x00000000
		# : USB0 PIPE POWER PRESENT
		# Register : fpd_power_prsnt @ 0XFF9D0080</p>

		# This bit is used to choose between PIPE power present and 1'b1
		# PSU_USB3_0_FPD_POWER_PRSNT_OPTION                                               0X1

		# fpd_power_prsnt
		#(OFFSET, MASK, VALUE)      (0XFF9D0080, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF9D0080 0x00000001 0x00000001
		# Register : fpd_pipe_clk @ 0XFF9D007C</p>

		# This bit is used to choose between PIPE clock coming from SerDes and the
    #  suspend clk
		# PSU_USB3_0_FPD_PIPE_CLK_OPTION                                                  0x0

		# fpd_pipe_clk
		#(OFFSET, MASK, VALUE)      (0XFF9D007C, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF9D007C 0x00000001 0x00000000
		# : SD
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_SDIO1_RESET                                            0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000040U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000040 0x00000000
		# Register : CTRL_REG_SD @ 0XFF180310</p>

		# SD or eMMC selection on SDIO1 0: SD enabled 1: eMMC enabled
		# PSU_IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL                                           0

		# SD eMMC selection
		#(OFFSET, MASK, VALUE)      (0XFF180310, 0x00008000U ,0x00000000U)  */
    mask_write 0XFF180310 0x00008000 0x00000000
		# Register : SD_CONFIG_REG2 @ 0XFF180320</p>

		# Should be set based on the final product usage 00 - Removable SCard Slot
    #  01 - Embedded Slot for One Device 10 - Shared Bus Slot 11 - Reserved
		# PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE                                        0

		# 1.8V Support 1: 1.8V supported 0: 1.8V not supported support
		# PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V                                            1

		# 3.0V Support 1: 3.0V supported 0: 3.0V not supported support
		# PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V                                            0

		# 3.3V Support 1: 3.3V supported 0: 3.3V not supported support
		# PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V                                            1

		# SD Config Register 2
		#(OFFSET, MASK, VALUE)      (0XFF180320, 0x33800000U ,0x02800000U)  */
    mask_write 0XFF180320 0x33800000 0x02800000
		# : SD1 BASE CLOCK
		# Register : SD_CONFIG_REG1 @ 0XFF18031C</p>

		# Base Clock Frequency for SD Clock. This is the frequency of the xin_clk.
		# PSU_IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK                                         0xc8

		# Configures the Number of Taps (Phases) of the rxclk_in that is supported
    # .
		# PSU_IOU_SLCR_SD_CONFIG_REG1_SD1_TUNIGCOUNT                                      0x28

		# SD Config Register 1
		#(OFFSET, MASK, VALUE)      (0XFF18031C, 0x7FFE0000U ,0x64500000U)  */
    mask_write 0XFF18031C 0x7FFE0000 0x64500000
		# Register : SD_DLL_CTRL @ 0XFF180358</p>

		# Reserved.
		# PSU_IOU_SLCR_SD_DLL_CTRL_RESERVED                                               1

		# SDIO status register
		#(OFFSET, MASK, VALUE)      (0XFF180358, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF180358 0x00000008 0x00000008
		# : SD1 RETUNER
		# Register : SD_CONFIG_REG3 @ 0XFF180324</p>

		# This is the Timer Count for Re-Tuning Timer for Re-Tuning Mode 1 to 3. S
    # etting to 4'b0 disables Re-Tuning Timer. 0h - Get information via other
    # source 1h = 1 seconds 2h = 2 seconds 3h = 4 seconds 4h = 8 seconds -- n
    # = 2(n-1) seconds -- Bh = 1024 seconds Fh - Ch = Reserved
		# PSU_IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR                                       0X0

		# SD Config Register 3
		#(OFFSET, MASK, VALUE)      (0XFF180324, 0x03C00000U ,0x00000000U)  */
    mask_write 0XFF180324 0x03C00000 0x00000000
		# : CAN
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_CAN1_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000100U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000100 0x00000000
		# : I2C
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_I2C0_RESET                                             0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_I2C1_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000600U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000600 0x00000000
		# : SWDT
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_SWDT_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00008000U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00008000 0x00000000
		# : SPI
		# : TTC
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_TTC0_RESET                                             0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_TTC1_RESET                                             0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_TTC2_RESET                                             0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_TTC3_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00007800U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00007800 0x00000000
		# : UART
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_UART0_RESET                                            0

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_UART1_RESET                                            0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000006U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000006 0x00000000
		# : UART BAUD RATE
		# Register : Baud_rate_divider_reg0 @ 0XFF000034</p>

		# Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate
		# PSU_UART0_BAUD_RATE_DIVIDER_REG0_BDIV                                           0x5

		# Baud Rate Divider Register
		#(OFFSET, MASK, VALUE)      (0XFF000034, 0x000000FFU ,0x00000005U)  */
    mask_write 0XFF000034 0x000000FF 0x00000005
		# Register : Baud_rate_gen_reg0 @ 0XFF000018</p>

		# Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor
    # bypass (baud_sample = sel_clk) 2 - 65535: baud_sample
		# PSU_UART0_BAUD_RATE_GEN_REG0_CD                                                 0x8f

		# Baud Rate Generator Register.
		#(OFFSET, MASK, VALUE)      (0XFF000018, 0x0000FFFFU ,0x0000008FU)  */
    mask_write 0XFF000018 0x0000FFFF 0x0000008F
		# Register : Control_reg0 @ 0XFF000000</p>

		# Stop transmitter break: 0: no affect 1: stop transmission of the break a
    # fter a minimum of one character length and transmit a high level during
    # 12 bit periods. It can be set regardless of the value of STTBRK.
		# PSU_UART0_CONTROL_REG0_STPBRK                                                   0x0

		# Start transmitter break: 0: no affect 1: start to transmit a break after
    #  the characters currently present in the FIFO and the transmit shift reg
    # ister have been transmitted. It can only be set if STPBRK (Stop transmit
    # ter break) is not high.
		# PSU_UART0_CONTROL_REG0_STTBRK                                                   0x0

		# Restart receiver timeout counter: 1: receiver timeout counter is restart
    # ed. This bit is self clearing once the restart has completed.
		# PSU_UART0_CONTROL_REG0_RSTTO                                                    0x0

		# Transmit disable: 0: enable transmitter 1: disable transmitter
		# PSU_UART0_CONTROL_REG0_TXDIS                                                    0x0

		# Transmit enable: 0: disable transmitter 1: enable transmitter, provided
    # the TXDIS field is set to 0.
		# PSU_UART0_CONTROL_REG0_TXEN                                                     0x1

		# Receive disable: 0: enable 1: disable, regardless of the value of RXEN
		# PSU_UART0_CONTROL_REG0_RXDIS                                                    0x0

		# Receive enable: 0: disable 1: enable When set to one, the receiver logic
    #  is enabled, provided the RXDIS field is set to zero.
		# PSU_UART0_CONTROL_REG0_RXEN                                                     0x1

		# Software reset for Tx data path: 0: no affect 1: transmitter logic is re
    # set and all pending transmitter data is discarded This bit is self clear
    # ing once the reset has completed.
		# PSU_UART0_CONTROL_REG0_TXRES                                                    0x1

		# Software reset for Rx data path: 0: no affect 1: receiver logic is reset
    #  and all pending receiver data is discarded. This bit is self clearing o
    # nce the reset has completed.
		# PSU_UART0_CONTROL_REG0_RXRES                                                    0x1

		# UART Control Register
		#(OFFSET, MASK, VALUE)      (0XFF000000, 0x000001FFU ,0x00000017U)  */
    mask_write 0XFF000000 0x000001FF 0x00000017
		# Register : mode_reg0 @ 0XFF000004</p>

		# Channel mode: Defines the mode of operation of the UART. 00: normal 01:
    # automatic echo 10: local loopback 11: remote loopback
		# PSU_UART0_MODE_REG0_CHMODE                                                      0x0

		# Number of stop bits: Defines the number of stop bits to detect on receiv
    # e and to generate on transmit. 00: 1 stop bit 01: 1.5 stop bits 10: 2 st
    # op bits 11: reserved
		# PSU_UART0_MODE_REG0_NBSTOP                                                      0x0

		# Parity type select: Defines the expected parity to check on receive and
    # the parity to generate on transmit. 000: even parity 001: odd parity 010
    # : forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no pari
    # ty
		# PSU_UART0_MODE_REG0_PAR                                                         0x4

		# Character length select: Defines the number of bits in each character. 1
    # 1: 6 bits 10: 7 bits 0x: 8 bits
		# PSU_UART0_MODE_REG0_CHRL                                                        0x0

		# Clock source select: This field defines whether a pre-scalar of 8 is app
    # lied to the baud rate generator input clock. 0: clock source is uart_ref
    # _clk 1: clock source is uart_ref_clk/8
		# PSU_UART0_MODE_REG0_CLKS                                                        0x0

		# UART Mode Register
		#(OFFSET, MASK, VALUE)      (0XFF000004, 0x000003FFU ,0x00000020U)  */
    mask_write 0XFF000004 0x000003FF 0x00000020
		# Register : Baud_rate_divider_reg0 @ 0XFF010034</p>

		# Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate
		# PSU_UART1_BAUD_RATE_DIVIDER_REG0_BDIV                                           0x5

		# Baud Rate Divider Register
		#(OFFSET, MASK, VALUE)      (0XFF010034, 0x000000FFU ,0x00000005U)  */
    mask_write 0XFF010034 0x000000FF 0x00000005
		# Register : Baud_rate_gen_reg0 @ 0XFF010018</p>

		# Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor
    # bypass (baud_sample = sel_clk) 2 - 65535: baud_sample
		# PSU_UART1_BAUD_RATE_GEN_REG0_CD                                                 0x8f

		# Baud Rate Generator Register.
		#(OFFSET, MASK, VALUE)      (0XFF010018, 0x0000FFFFU ,0x0000008FU)  */
    mask_write 0XFF010018 0x0000FFFF 0x0000008F
		# Register : Control_reg0 @ 0XFF010000</p>

		# Stop transmitter break: 0: no affect 1: stop transmission of the break a
    # fter a minimum of one character length and transmit a high level during
    # 12 bit periods. It can be set regardless of the value of STTBRK.
		# PSU_UART1_CONTROL_REG0_STPBRK                                                   0x0

		# Start transmitter break: 0: no affect 1: start to transmit a break after
    #  the characters currently present in the FIFO and the transmit shift reg
    # ister have been transmitted. It can only be set if STPBRK (Stop transmit
    # ter break) is not high.
		# PSU_UART1_CONTROL_REG0_STTBRK                                                   0x0

		# Restart receiver timeout counter: 1: receiver timeout counter is restart
    # ed. This bit is self clearing once the restart has completed.
		# PSU_UART1_CONTROL_REG0_RSTTO                                                    0x0

		# Transmit disable: 0: enable transmitter 1: disable transmitter
		# PSU_UART1_CONTROL_REG0_TXDIS                                                    0x0

		# Transmit enable: 0: disable transmitter 1: enable transmitter, provided
    # the TXDIS field is set to 0.
		# PSU_UART1_CONTROL_REG0_TXEN                                                     0x1

		# Receive disable: 0: enable 1: disable, regardless of the value of RXEN
		# PSU_UART1_CONTROL_REG0_RXDIS                                                    0x0

		# Receive enable: 0: disable 1: enable When set to one, the receiver logic
    #  is enabled, provided the RXDIS field is set to zero.
		# PSU_UART1_CONTROL_REG0_RXEN                                                     0x1

		# Software reset for Tx data path: 0: no affect 1: transmitter logic is re
    # set and all pending transmitter data is discarded This bit is self clear
    # ing once the reset has completed.
		# PSU_UART1_CONTROL_REG0_TXRES                                                    0x1

		# Software reset for Rx data path: 0: no affect 1: receiver logic is reset
    #  and all pending receiver data is discarded. This bit is self clearing o
    # nce the reset has completed.
		# PSU_UART1_CONTROL_REG0_RXRES                                                    0x1

		# UART Control Register
		#(OFFSET, MASK, VALUE)      (0XFF010000, 0x000001FFU ,0x00000017U)  */
    mask_write 0XFF010000 0x000001FF 0x00000017
		# Register : mode_reg0 @ 0XFF010004</p>

		# Channel mode: Defines the mode of operation of the UART. 00: normal 01:
    # automatic echo 10: local loopback 11: remote loopback
		# PSU_UART1_MODE_REG0_CHMODE                                                      0x0

		# Number of stop bits: Defines the number of stop bits to detect on receiv
    # e and to generate on transmit. 00: 1 stop bit 01: 1.5 stop bits 10: 2 st
    # op bits 11: reserved
		# PSU_UART1_MODE_REG0_NBSTOP                                                      0x0

		# Parity type select: Defines the expected parity to check on receive and
    # the parity to generate on transmit. 000: even parity 001: odd parity 010
    # : forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no pari
    # ty
		# PSU_UART1_MODE_REG0_PAR                                                         0x4

		# Character length select: Defines the number of bits in each character. 1
    # 1: 6 bits 10: 7 bits 0x: 8 bits
		# PSU_UART1_MODE_REG0_CHRL                                                        0x0

		# Clock source select: This field defines whether a pre-scalar of 8 is app
    # lied to the baud rate generator input clock. 0: clock source is uart_ref
    # _clk 1: clock source is uart_ref_clk/8
		# PSU_UART1_MODE_REG0_CLKS                                                        0x0

		# UART Mode Register
		#(OFFSET, MASK, VALUE)      (0XFF010004, 0x000003FFU ,0x00000020U)  */
    mask_write 0XFF010004 0x000003FF 0x00000020
		# : GPIO
		# Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

		# Block level reset
		# PSU_CRL_APB_RST_LPD_IOU2_GPIO_RESET                                             0

		# Software control register for the IOU block. Each bit will cause a singl
    # erperipheral or part of the peripheral to be reset.
		#(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00040000U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00040000 0x00000000
		# : ADMA TZ
		# Register : slcr_adma @ 0XFF4B0024</p>

		# TrustZone Classification for ADMA
		# PSU_LPD_SLCR_SECURE_SLCR_ADMA_TZ                                                0XFF

		# RPU TrustZone settings
		#(OFFSET, MASK, VALUE)      (0XFF4B0024, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFF4B0024 0x000000FF 0x000000FF
		# : CSU TAMPERING
		# : CSU TAMPER STATUS
		# Register : tamper_status @ 0XFFCA5000</p>

		# CSU regsiter
		# PSU_CSU_TAMPER_STATUS_TAMPER_0                                                  0

		# External MIO
		# PSU_CSU_TAMPER_STATUS_TAMPER_1                                                  0

		# JTAG toggle detect
		# PSU_CSU_TAMPER_STATUS_TAMPER_2                                                  0

		# PL SEU error
		# PSU_CSU_TAMPER_STATUS_TAMPER_3                                                  0

		# AMS over temperature alarm for LPD
		# PSU_CSU_TAMPER_STATUS_TAMPER_4                                                  0

		# AMS over temperature alarm for APU
		# PSU_CSU_TAMPER_STATUS_TAMPER_5                                                  0

		# AMS voltage alarm for VCCPINT_FPD
		# PSU_CSU_TAMPER_STATUS_TAMPER_6                                                  0

		# AMS voltage alarm for VCCPINT_LPD
		# PSU_CSU_TAMPER_STATUS_TAMPER_7                                                  0

		# AMS voltage alarm for VCCPAUX
		# PSU_CSU_TAMPER_STATUS_TAMPER_8                                                  0

		# AMS voltage alarm for DDRPHY
		# PSU_CSU_TAMPER_STATUS_TAMPER_9                                                  0

		# AMS voltage alarm for PSIO bank 0/1/2
		# PSU_CSU_TAMPER_STATUS_TAMPER_10                                                 0

		# AMS voltage alarm for PSIO bank 3 (dedicated pins)
		# PSU_CSU_TAMPER_STATUS_TAMPER_11                                                 0

		# AMS voltaage alarm for GT
		# PSU_CSU_TAMPER_STATUS_TAMPER_12                                                 0

		# Tamper Response Status
		#(OFFSET, MASK, VALUE)      (0XFFCA5000, 0x00001FFFU ,0x00000000U)  */
    mask_write 0XFFCA5000 0x00001FFF 0x00000000
		# : CSU TAMPER RESPONSE
		# : CPU QOS DEFAULT
		# Register : ACE_CTRL @ 0XFD5C0060</p>

		# Set ACE outgoing AWQOS value
		# PSU_APU_ACE_CTRL_AWQOS                                                          0X0

		# Set ACE outgoing ARQOS value
		# PSU_APU_ACE_CTRL_ARQOS                                                          0X0

		# ACE Control Register
		#(OFFSET, MASK, VALUE)      (0XFD5C0060, 0x000F000FU ,0x00000000U)  */
    mask_write 0XFD5C0060 0x000F000F 0x00000000
		# : ENABLES RTC SWITCH TO BATTERY WHEN VCC_PSAUX IS NOT AVAILABLE
		# Register : CONTROL @ 0XFFA60040</p>

		# Enables the RTC. By writing a 0 to this bit, RTC will be powered off and
    #  the only module that potentially draws current from the battery will be
    #  BBRAM. The value read through this bit does not necessarily reflect whe
    # ther RTC is enabled or not. It is expected that RTC is enabled every tim
    # e it is being configured. If RTC is not used in the design, FSBL will di
    # sable it by writing a 0 to this bit.
		# PSU_RTC_CONTROL_BATTERY_DISABLE                                                 0X1

		# This register controls various functionalities within the RTC
		#(OFFSET, MASK, VALUE)      (0XFFA60040, 0x80000000U ,0x80000000U)  */
    mask_write 0XFFA60040 0x80000000 0x80000000
		# : TIMESTAMP COUNTER
		# Register : base_frequency_ID_register @ 0XFF260020</p>

		# Frequency in number of ticks per second. Valid range from 10 MHz to 100
    # MHz.
		# PSU_IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ                                  0x5f5b9f0

		# Program this register to match the clock frequency of the timestamp gene
    # rator, in ticks per second. For example, for a 50 MHz clock, program 0x0
    # 2FAF080. This register is not accessible to the read-only programming in
    # terface.
		#(OFFSET, MASK, VALUE)      (0XFF260020, 0xFFFFFFFFU ,0x05F5B9F0U)  */
    mask_write 0XFF260020 0xFFFFFFFF 0x05F5B9F0
		# Register : counter_control_register @ 0XFF260000</p>

		# Enable 0: The counter is disabled and not incrementing. 1: The counter i
    # s enabled and is incrementing.
		# PSU_IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN                                      0x1

		# Controls the counter increments. This register is not accessible to the
    # read-only programming interface.
		#(OFFSET, MASK, VALUE)      (0XFF260000, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF260000 0x00000001 0x00000001
		# : TTC SRC SELECT
		# : PCIE GPIO RESET
		# : PCIE RESET
		# : DIR MODE BANK 0
		# : DIR MODE BANK 1
		# Register : DIRM_1 @ 0XFF0A0244</p>

		# Operation is the same as DIRM_0[DIRECTION_0]
		# PSU_GPIO_DIRM_1_DIRECTION_1                                                     0x20

		# Direction mode (GPIO Bank1, MIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0244, 0x03FFFFFFU ,0x00000020U)  */
    mask_write 0XFF0A0244 0x03FFFFFF 0x00000020
		# : DIR MODE BANK 2
		# : OUTPUT ENABLE BANK 0
		# : OUTPUT ENABLE BANK 1
		# Register : OEN_1 @ 0XFF0A0248</p>

		# Operation is the same as OEN_0[OP_ENABLE_0]
		# PSU_GPIO_OEN_1_OP_ENABLE_1                                                      0x20

		# Output enable (GPIO Bank1, MIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0248, 0x03FFFFFFU ,0x00000020U)  */
    mask_write 0XFF0A0248 0x03FFFFFF 0x00000020
		# : OUTPUT ENABLE BANK 2
		# : MASK_DATA_0_LSW LOW BANK [15:0]
		# : MASK_DATA_0_MSW LOW BANK [25:16]
		# : MASK_DATA_1_LSW LOW BANK [41:26]
		# Register : MASK_DATA_1_LSW @ 0XFF0A0008</p>

		# Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW]
		# PSU_GPIO_MASK_DATA_1_LSW_MASK_1_LSW                                             0xffdf

		# Operation is the same as MASK_DATA_0_LSW[DATA_0_LSW]
		# PSU_GPIO_MASK_DATA_1_LSW_DATA_1_LSW                                             0x20

		# Maskable Output Data (GPIO Bank1, MIO, Lower 16bits)
		#(OFFSET, MASK, VALUE)      (0XFF0A0008, 0xFFFFFFFFU ,0xFFDF0020U)  */
    mask_write 0XFF0A0008 0xFFFFFFFF 0xFFDF0020
		# : MASK_DATA_1_MSW HIGH BANK [51:42]
		# : MASK_DATA_1_LSW HIGH BANK [67:52]
		# : MASK_DATA_1_LSW HIGH BANK [77:68]
		# : ADD 1 MS DELAY
    mask_delay 0x00000000 1
		# : MASK_DATA_0_LSW LOW BANK [15:0]
		# : MASK_DATA_0_MSW LOW BANK [25:16]
		# : MASK_DATA_1_LSW LOW BANK [41:26]
		# Register : MASK_DATA_1_LSW @ 0XFF0A0008</p>

		# Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW]
		# PSU_GPIO_MASK_DATA_1_LSW_MASK_1_LSW                                             0xffdf

		# Operation is the same as MASK_DATA_0_LSW[DATA_0_LSW]
		# PSU_GPIO_MASK_DATA_1_LSW_DATA_1_LSW                                             0x0

		# Maskable Output Data (GPIO Bank1, MIO, Lower 16bits)
		#(OFFSET, MASK, VALUE)      (0XFF0A0008, 0xFFFFFFFFU ,0xFFDF0000U)  */
    mask_write 0XFF0A0008 0xFFFFFFFF 0xFFDF0000
		# : MASK_DATA_1_MSW HIGH BANK [51:42]
		# : MASK_DATA_1_LSW HIGH BANK [67:52]
		# : MASK_DATA_1_LSW HIGH BANK [77:68]
		# : ADD 5 MS DELAY
    mask_delay 0x00000000 5
}

set psu_post_config_data {
		# : POST_CONFIG
}

set psu_peripherals_powerdwn_data {
		# : POWER DOWN REQUEST INTERRUPT ENABLE
		# : POWER DOWN TRIGGER
}

set psu_lpd_xppu_data {
		# : MASTER ID LIST
		# : APERTURE PERMISIION LIST
		# : APERTURE NAME: UART0, START ADDRESS: FF000000, END ADDRESS: FF00FFFF
		# : APERTURE NAME: UART1, START ADDRESS: FF010000, END ADDRESS: FF01FFFF
		# : APERTURE NAME: I2C0, START ADDRESS: FF020000, END ADDRESS: FF02FFFF
		# : APERTURE NAME: I2C1, START ADDRESS: FF030000, END ADDRESS: FF03FFFF
		# : APERTURE NAME: SPI0, START ADDRESS: FF040000, END ADDRESS: FF04FFFF
		# : APERTURE NAME: SPI1, START ADDRESS: FF050000, END ADDRESS: FF05FFFF
		# : APERTURE NAME: CAN0, START ADDRESS: FF060000, END ADDRESS: FF06FFFF
		# : APERTURE NAME: CAN1, START ADDRESS: FF070000, END ADDRESS: FF07FFFF
		# : APERTURE NAME: RPU_UNUSED_12, START ADDRESS: FF080000, END ADDRESS: FF09FFFF
		# : APERTURE NAME: RPU_UNUSED_12, START ADDRESS: FF080000, END ADDRESS: FF09FFFF
		# : APERTURE NAME: GPIO, START ADDRESS: FF0A0000, END ADDRESS: FF0AFFFF
		# : APERTURE NAME: GEM0, START ADDRESS: FF0B0000, END ADDRESS: FF0BFFFF
		# : APERTURE NAME: GEM1, START ADDRESS: FF0C0000, END ADDRESS: FF0CFFFF
		# : APERTURE NAME: GEM2, START ADDRESS: FF0D0000, END ADDRESS: FF0DFFFF
		# : APERTURE NAME: GEM3, START ADDRESS: FF0E0000, END ADDRESS: FF0EFFFF
		# : APERTURE NAME: QSPI, START ADDRESS: FF0F0000, END ADDRESS: FF0FFFFF
		# : APERTURE NAME: NAND, START ADDRESS: FF100000, END ADDRESS: FF10FFFF
		# : APERTURE NAME: TTC0, START ADDRESS: FF110000, END ADDRESS: FF11FFFF
		# : APERTURE NAME: TTC1, START ADDRESS: FF120000, END ADDRESS: FF12FFFF
		# : APERTURE NAME: TTC2, START ADDRESS: FF130000, END ADDRESS: FF13FFFF
		# : APERTURE NAME: TTC3, START ADDRESS: FF140000, END ADDRESS: FF14FFFF
		# : APERTURE NAME: SWDT, START ADDRESS: FF150000, END ADDRESS: FF15FFFF
		# : APERTURE NAME: SD0, START ADDRESS: FF160000, END ADDRESS: FF16FFFF
		# : APERTURE NAME: SD1, START ADDRESS: FF170000, END ADDRESS: FF17FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF
		# : APERTURE NAME: IOU_SECURE_SLCR, START ADDRESS: FF240000, END ADDRESS: FF24FFFF
		# : APERTURE NAME: IOU_SCNTR, START ADDRESS: FF250000, END ADDRESS: FF25FFFF
		# : APERTURE NAME: IOU_SCNTRS, START ADDRESS: FF260000, END ADDRESS: FF26FFFF
		# : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF
		# : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF
		# : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF
		# : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF
		# : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF
		# : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF
		# : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF
		# : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF
		# : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF
		# : APERTURE NAME: LPD_UNUSED_1, START ADDRESS: FF400000, END ADDRESS: FF40FFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF
		# : APERTURE NAME: LPD_SLCR_SECURE, START ADDRESS: FF4B0000, END ADDRESS: FF4DFFFF
		# : APERTURE NAME: LPD_SLCR_SECURE, START ADDRESS: FF4B0000, END ADDRESS: FF4DFFFF
		# : APERTURE NAME: LPD_SLCR_SECURE, START ADDRESS: FF4B0000, END ADDRESS: FF4DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF
		# : APERTURE NAME: OCM_SLCR, START ADDRESS: FF960000, END ADDRESS: FF96FFFF
		# : APERTURE NAME: LPD_UNUSED_4, START ADDRESS: FF970000, END ADDRESS: FF97FFFF
		# : APERTURE NAME: LPD_XPPU, START ADDRESS: FF980000, END ADDRESS: FF99FFFF
		# : APERTURE NAME: RPU, START ADDRESS: FF9A0000, END ADDRESS: FF9AFFFF
		# : APERTURE NAME: AFIFM6, START ADDRESS: FF9B0000, END ADDRESS: FF9BFFFF
		# : APERTURE NAME: LPD_XPPU_SINK, START ADDRESS: FF9C0000, END ADDRESS: FF9CFFFF
		# : APERTURE NAME: USB3_0, START ADDRESS: FF9D0000, END ADDRESS: FF9DFFFF
		# : APERTURE NAME: USB3_1, START ADDRESS: FF9E0000, END ADDRESS: FF9EFFFF
		# : APERTURE NAME: LPD_UNUSED_5, START ADDRESS: FF9F0000, END ADDRESS: FF9FFFFF
		# : APERTURE NAME: APM0, START ADDRESS: FFA00000, END ADDRESS: FFA0FFFF
		# : APERTURE NAME: APM1, START ADDRESS: FFA10000, END ADDRESS: FFA1FFFF
		# : APERTURE NAME: APM_INTC_IOU, START ADDRESS: FFA20000, END ADDRESS: FFA2FFFF
		# : APERTURE NAME: APM_FPD_LPD, START ADDRESS: FFA30000, END ADDRESS: FFA3FFFF
		# : APERTURE NAME: LPD_UNUSED_6, START ADDRESS: FFA40000, END ADDRESS: FFA4FFFF
		# : APERTURE NAME: AMS, START ADDRESS: FFA50000, END ADDRESS: FFA5FFFF
		# : APERTURE NAME: RTC, START ADDRESS: FFA60000, END ADDRESS: FFA6FFFF
		# : APERTURE NAME: OCM_XMPU_CFG, START ADDRESS: FFA70000, END ADDRESS: FFA7FFFF
		# : APERTURE NAME: ADMA_0, START ADDRESS: FFA80000, END ADDRESS: FFA8FFFF
		# : APERTURE NAME: ADMA_1, START ADDRESS: FFA90000, END ADDRESS: FFA9FFFF
		# : APERTURE NAME: ADMA_2, START ADDRESS: FFAA0000, END ADDRESS: FFAAFFFF
		# : APERTURE NAME: ADMA_3, START ADDRESS: FFAB0000, END ADDRESS: FFABFFFF
		# : APERTURE NAME: ADMA_4, START ADDRESS: FFAC0000, END ADDRESS: FFACFFFF
		# : APERTURE NAME: ADMA_5, START ADDRESS: FFAD0000, END ADDRESS: FFADFFFF
		# : APERTURE NAME: ADMA_6, START ADDRESS: FFAE0000, END ADDRESS: FFAEFFFF
		# : APERTURE NAME: ADMA_7, START ADDRESS: FFAF0000, END ADDRESS: FFAFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF
		# : APERTURE NAME: CSU_ROM, START ADDRESS: FFC00000, END ADDRESS: FFC1FFFF
		# : APERTURE NAME: CSU_ROM, START ADDRESS: FFC00000, END ADDRESS: FFC1FFFF
		# : APERTURE NAME: CSU_LOCAL, START ADDRESS: FFC20000, END ADDRESS: FFC2FFFF
		# : APERTURE NAME: PUF, START ADDRESS: FFC30000, END ADDRESS: FFC3FFFF
		# : APERTURE NAME: CSU_RAM, START ADDRESS: FFC40000, END ADDRESS: FFC5FFFF
		# : APERTURE NAME: CSU_RAM, START ADDRESS: FFC40000, END ADDRESS: FFC5FFFF
		# : APERTURE NAME: CSU_IOMODULE, START ADDRESS: FFC60000, END ADDRESS: FFC7FFFF
		# : APERTURE NAME: CSU_IOMODULE, START ADDRESS: FFC60000, END ADDRESS: FFC7FFFF
		# : APERTURE NAME: CSUDMA, START ADDRESS: FFC80000, END ADDRESS: FFC9FFFF
		# : APERTURE NAME: CSUDMA, START ADDRESS: FFC80000, END ADDRESS: FFC9FFFF
		# : APERTURE NAME: CSU, START ADDRESS: FFCA0000, END ADDRESS: FFCAFFFF
		# : APERTURE NAME: CSU_WDT, START ADDRESS: FFCB0000, END ADDRESS: FFCBFFFF
		# : APERTURE NAME: EFUSE, START ADDRESS: FFCC0000, END ADDRESS: FFCCFFFF
		# : APERTURE NAME: BBRAM, START ADDRESS: FFCD0000, END ADDRESS: FFCDFFFF
		# : APERTURE NAME: RSA_CORE, START ADDRESS: FFCE0000, END ADDRESS: FFCEFFFF
		# : APERTURE NAME: MBISTJTAG, START ADDRESS: FFCF0000, END ADDRESS: FFCFFFFF
		# : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF
		# : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF
		# : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF
		# : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF
		# : APERTURE NAME: PMU_IOMODULE, START ADDRESS: FFD40000, END ADDRESS: FFD5FFFF
		# : APERTURE NAME: PMU_IOMODULE, START ADDRESS: FFD40000, END ADDRESS: FFD5FFFF
		# : APERTURE NAME: PMU_LOCAL, START ADDRESS: FFD60000, END ADDRESS: FFD7FFFF
		# : APERTURE NAME: PMU_LOCAL, START ADDRESS: FFD60000, END ADDRESS: FFD7FFFF
		# : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF
		# : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF
		# : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF
		# : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF
		# : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF
		# : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF
		# : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF
		# : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF
		# : APERTURE NAME: R5_0_ATCM, START ADDRESS: FFE00000, END ADDRESS: FFE0FFFF
		# : APERTURE NAME: R5_0_ATCM_LOCKSTEP, START ADDRESS: FFE10000, END ADDRESS: FFE1FFFF
		# : APERTURE NAME: R5_0_BTCM, START ADDRESS: FFE20000, END ADDRESS: FFE2FFFF
		# : APERTURE NAME: R5_0_BTCM_LOCKSTEP, START ADDRESS: FFE30000, END ADDRESS: FFE3FFFF
		# : APERTURE NAME: R5_0_INSTRUCTION_CACHE, START ADDRESS: FFE40000, END ADDRESS: FFE4FFFF
		# : APERTURE NAME: R5_0_DATA_CACHE, START ADDRESS: FFE50000, END ADDRESS: FFE5FFFF
		# : APERTURE NAME: LPD_UNUSED_8, START ADDRESS: FFE60000, END ADDRESS: FFE8FFFF
		# : APERTURE NAME: LPD_UNUSED_8, START ADDRESS: FFE60000, END ADDRESS: FFE8FFFF
		# : APERTURE NAME: LPD_UNUSED_8, START ADDRESS: FFE60000, END ADDRESS: FFE8FFFF
		# : APERTURE NAME: R5_1_ATCM_, START ADDRESS: FFE90000, END ADDRESS: FFE9FFFF
		# : APERTURE NAME: RPU_UNUSED_10, START ADDRESS: FFEA0000, END ADDRESS: FFEAFFFF
		# : APERTURE NAME: R5_1_BTCM_, START ADDRESS: FFEB0000, END ADDRESS: FFEBFFFF
		# : APERTURE NAME: R5_1_INSTRUCTION_CACHE, START ADDRESS: FFEC0000, END ADDRESS: FFECFFFF
		# : APERTURE NAME: R5_1_DATA_CACHE, START ADDRESS: FFED0000, END ADDRESS: FFEDFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF
		# : APERTURE NAME: LPD_UNUSED_15, START ADDRESS: FFFD0000, END ADDRESS: FFFFFFFF
		# : APERTURE NAME: LPD_UNUSED_15, START ADDRESS: FFFD0000, END ADDRESS: FFFFFFFF
		# : APERTURE NAME: LPD_UNUSED_15, START ADDRESS: FFFD0000, END ADDRESS: FFFFFFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF
		# : APERTURE NAME: IOU_GPV, START ADDRESS: FE000000, END ADDRESS: FE0FFFFF
		# : APERTURE NAME: LPD_GPV, START ADDRESS: FE100000, END ADDRESS: FE1FFFFF
		# : APERTURE NAME: USB3_0_XHCI, START ADDRESS: FE200000, END ADDRESS: FE2FFFFF
		# : APERTURE NAME: USB3_1_XHCI, START ADDRESS: FE300000, END ADDRESS: FE3FFFFF
		# : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF
		# : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF
		# : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF
		# : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF
		# : APERTURE NAME: QSPI_LINEAR_ADDRESS, START ADDRESS: C0000000, END ADDRESS: DFFFFFFF
		# : XPPU CONTROL
}

set psu_ddr_xmpu0_data {
		# : DDR XMPU0
}

set psu_ddr_xmpu1_data {
		# : DDR XMPU1
}

set psu_ddr_xmpu2_data {
		# : DDR XMPU2
}

set psu_ddr_xmpu3_data {
		# : DDR XMPU3
}

set psu_ddr_xmpu4_data {
		# : DDR XMPU4
}

set psu_ddr_xmpu5_data {
		# : DDR XMPU5
}

set psu_ocm_xmpu_data {
		# : OCM XMPU
}

set psu_fpd_xmpu_data {
		# : FPD XMPU
}

set psu_protection_lock_data {
		# : LOCKING PROTECTION MODULE
		# : XPPU LOCK
		# : APERTURE NAME: LPD_XPPU, START ADDRESS: FF980000, END ADDRESS: FF99FFFF
		# : XMPU LOCK
		# : LOCK OCM XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK FPD XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK DDR XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK DDR XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK DDR XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK DDR XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK DDR XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
		# : LOCK DDR XMPU ONLY IF IT IS NOT PROTECTED BY ANY MASTER
}

set psu_apply_master_tz {
		# : RPU
		# : DP TZ
		# Register : slcr_dpdma @ 0XFD690040</p>

		# TrustZone classification for DisplayPort DMA
		# PSU_FPD_SLCR_SECURE_SLCR_DPDMA_TZ                                               1

		# DPDMA TrustZone Settings
		#(OFFSET, MASK, VALUE)      (0XFD690040, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD690040 0x00000001 0x00000001
		# : SATA TZ
		# : PCIE TZ
		# Register : slcr_pcie @ 0XFD690030</p>

		# TrustZone classification for DMA Channel 0
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_DMA_0                                          1

		# TrustZone classification for DMA Channel 1
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_DMA_1                                          1

		# TrustZone classification for DMA Channel 2
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_DMA_2                                          1

		# TrustZone classification for DMA Channel 3
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_DMA_3                                          1

		# TrustZone classification for Ingress Address Translation 0
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_0                                      1

		# TrustZone classification for Ingress Address Translation 1
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_1                                      1

		# TrustZone classification for Ingress Address Translation 2
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_2                                      1

		# TrustZone classification for Ingress Address Translation 3
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_3                                      1

		# TrustZone classification for Ingress Address Translation 4
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_4                                      1

		# TrustZone classification for Ingress Address Translation 5
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_5                                      1

		# TrustZone classification for Ingress Address Translation 6
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_6                                      1

		# TrustZone classification for Ingress Address Translation 7
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_INGR_7                                      1

		# TrustZone classification for Egress Address Translation 0
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_0                                       1

		# TrustZone classification for Egress Address Translation 1
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_1                                       1

		# TrustZone classification for Egress Address Translation 2
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_2                                       1

		# TrustZone classification for Egress Address Translation 3
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_3                                       1

		# TrustZone classification for Egress Address Translation 4
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_4                                       1

		# TrustZone classification for Egress Address Translation 5
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_5                                       1

		# TrustZone classification for Egress Address Translation 6
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_6                                       1

		# TrustZone classification for Egress Address Translation 7
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_AT_EGR_7                                       1

		# TrustZone classification for DMA Registers
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_DMA_REGS                                       1

		# TrustZone classification for MSIx Table
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_MSIX_TABLE                                     1

		# TrustZone classification for MSIx PBA
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_MSIX_PBA                                       1

		# TrustZone classification for ECAM
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_ECAM                                           1

		# TrustZone classification for Bridge Common Registers
		# PSU_FPD_SLCR_SECURE_SLCR_PCIE_TZ_BRIDGE_REGS                                    1

		# PCIe TrustZone settings. This register may only be modified during bootu
    # p (while PCIe block is disabled)
		#(OFFSET, MASK, VALUE)      (0XFD690030, 0x01FFFFFFU ,0x01FFFFFFU)  */
    mask_write 0XFD690030 0x01FFFFFF 0x01FFFFFF
		# : USB TZ
		# Register : slcr_usb @ 0XFF4B0034</p>

		# TrustZone Classification for USB3_0
		# PSU_LPD_SLCR_SECURE_SLCR_USB_TZ_USB3_0                                          1

		# TrustZone Classification for USB3_1
		# PSU_LPD_SLCR_SECURE_SLCR_USB_TZ_USB3_1                                          1

		# USB3 TrustZone settings
		#(OFFSET, MASK, VALUE)      (0XFF4B0034, 0x00000003U ,0x00000003U)  */
    mask_write 0XFF4B0034 0x00000003 0x00000003
		# : SD TZ
		# Register : IOU_AXI_RPRTCN @ 0XFF240004</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_SD0_AXI_ARPROT                               2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_SD1_AXI_ARPROT                               2

		# AXI read protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240004, 0x003F0000U ,0x00120000U)  */
    mask_write 0XFF240004 0x003F0000 0x00120000
		# Register : IOU_AXI_WPRTCN @ 0XFF240000</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_SD0_AXI_AWPROT                               2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_SD1_AXI_AWPROT                               2

		# AXI write protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240000, 0x003F0000U ,0x00120000U)  */
    mask_write 0XFF240000 0x003F0000 0x00120000
		# : GEM TZ
		# Register : IOU_AXI_RPRTCN @ 0XFF240004</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_GEM0_AXI_ARPROT                              2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_GEM1_AXI_ARPROT                              2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_GEM2_AXI_ARPROT                              2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_GEM3_AXI_ARPROT                              2

		# AXI read protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240004, 0x00000FFFU ,0x00000492U)  */
    mask_write 0XFF240004 0x00000FFF 0x00000492
		# Register : IOU_AXI_WPRTCN @ 0XFF240000</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_GEM0_AXI_AWPROT                              2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_GEM1_AXI_AWPROT                              2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_GEM2_AXI_AWPROT                              2

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_GEM3_AXI_AWPROT                              2

		# AXI write protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240000, 0x00000FFFU ,0x00000492U)  */
    mask_write 0XFF240000 0x00000FFF 0x00000492
		# : QSPI TZ
		# Register : IOU_AXI_WPRTCN @ 0XFF240000</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_QSPI_AXI_AWPROT                              2

		# AXI write protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240000, 0x0E000000U ,0x04000000U)  */
    mask_write 0XFF240000 0x0E000000 0x04000000
		# : NAND TZ
		# Register : IOU_AXI_RPRTCN @ 0XFF240004</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_RPRTCN_NAND_AXI_ARPROT                              2

		# AXI read protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240004, 0x01C00000U ,0x00800000U)  */
    mask_write 0XFF240004 0x01C00000 0x00800000
		# Register : IOU_AXI_WPRTCN @ 0XFF240000</p>

		# AXI protection [0] = '0' : Normal access [0] = '1' : Previleged access [
    # 1] = '0' : Secure access [1] = '1' : No secure access [2] = '0' : Data a
    # ccess [2] = '1'' : Instruction access
		# PSU_IOU_SECURE_SLCR_IOU_AXI_WPRTCN_NAND_AXI_AWPROT                              2

		# AXI write protection type selection
		#(OFFSET, MASK, VALUE)      (0XFF240000, 0x01C00000U ,0x00800000U)  */
    mask_write 0XFF240000 0x01C00000 0x00800000
		# : DMA TZ
		# Register : slcr_adma @ 0XFF4B0024</p>

		# TrustZone Classification for ADMA
		# PSU_LPD_SLCR_SECURE_SLCR_ADMA_TZ                                                0xFF

		# RPU TrustZone settings
		#(OFFSET, MASK, VALUE)      (0XFF4B0024, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFF4B0024 0x000000FF 0x000000FF
		# Register : slcr_gdma @ 0XFD690050</p>

		# TrustZone Classification for GDMA
		# PSU_FPD_SLCR_SECURE_SLCR_GDMA_TZ                                                0xFF

		# GDMA Trustzone Settings
		#(OFFSET, MASK, VALUE)      (0XFD690050, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD690050 0x000000FF 0x000000FF
}

set psu_serdes_init_data {
		# : SERDES INITIALIZATION
		# : GT REFERENCE CLOCK SOURCE SELECTION
		# Register : PLL_REF_SEL0 @ 0XFD410000</p>

		# PLL0 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 1
    # 2MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 24MHz, 0x8 - 26MHz,
    #  0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE
    #  - 108MHz, 0xF - 125MHz, 0x10 - 135MHz, 0x11 - 150 MHz. 0x12 to 0x1F - R
    # eserved
		# PSU_SERDES_PLL_REF_SEL0_PLLREFSEL0                                              0xD

		# PLL0 Reference Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD410000, 0x0000001FU ,0x0000000DU)  */
    mask_write 0XFD410000 0x0000001F 0x0000000D
		# Register : PLL_REF_SEL1 @ 0XFD410004</p>

		# PLL1 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 1
    # 2MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 24MHz, 0x8 - 26MHz,
    #  0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE
    #  - 108MHz, 0xF - 125MHz, 0x10 - 135MHz, 0x11 - 150 MHz. 0x12 to 0x1F - R
    # eserved
		# PSU_SERDES_PLL_REF_SEL1_PLLREFSEL1                                              0x9

		# PLL1 Reference Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD410004, 0x0000001FU ,0x00000009U)  */
    mask_write 0XFD410004 0x0000001F 0x00000009
		# Register : PLL_REF_SEL2 @ 0XFD410008</p>

		# PLL2 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 1
    # 2MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 24MHz, 0x8 - 26MHz,
    #  0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE
    #  - 108MHz, 0xF - 125MHz, 0x10 - 135MHz, 0x11 - 150 MHz. 0x12 to 0x1F - R
    # eserved
		# PSU_SERDES_PLL_REF_SEL2_PLLREFSEL2                                              0x8

		# PLL2 Reference Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD410008, 0x0000001FU ,0x00000008U)  */
    mask_write 0XFD410008 0x0000001F 0x00000008
		# Register : PLL_REF_SEL3 @ 0XFD41000C</p>

		# PLL3 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 1
    # 2MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 24MHz, 0x8 - 26MHz,
    #  0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE
    #  - 108MHz, 0xF - 125MHz, 0x10 - 135MHz, 0x11 - 150 MHz. 0x12 to 0x1F - R
    # eserved
		# PSU_SERDES_PLL_REF_SEL3_PLLREFSEL3                                              0xF

		# PLL3 Reference Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD41000C, 0x0000001FU ,0x0000000FU)  */
    mask_write 0XFD41000C 0x0000001F 0x0000000F
		# : GT REFERENCE CLOCK FREQUENCY SELECTION
		# Register : L0_L0_REF_CLK_SEL @ 0XFD402860</p>

		# Sel of lane 0 ref clock local mux. Set to 1 to select lane 0 slicer outp
    # ut. Set to 0 to select lane0 ref clock mux output.
		# PSU_SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL                                 0x1

		# Lane0 Ref Clock Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD402860, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD402860 0x00000080 0x00000080
		# Register : L0_L1_REF_CLK_SEL @ 0XFD402864</p>

		# Sel of lane 1 ref clock local mux. Set to 1 to select lane 1 slicer outp
    # ut. Set to 0 to select lane1 ref clock mux output.
		# PSU_SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL                                 0x0

		# Bit 3 of lane 1 ref clock mux one hot sel. Set to 1 to select lane 3 sli
    # cer output from ref clock network
		# PSU_SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3                                   0x1

		# Lane1 Ref Clock Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD402864, 0x00000088U ,0x00000008U)  */
    mask_write 0XFD402864 0x00000088 0x00000008
		# Register : L0_L2_REF_CLK_SEL @ 0XFD402868</p>

		# Sel of lane 2 ref clock local mux. Set to 1 to select lane 1 slicer outp
    # ut. Set to 0 to select lane2 ref clock mux output.
		# PSU_SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL                                 0x1

		# Lane2 Ref Clock Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD402868, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD402868 0x00000080 0x00000080
		# Register : L0_L3_REF_CLK_SEL @ 0XFD40286C</p>

		# Sel of lane 3 ref clock local mux. Set to 1 to select lane 3 slicer outp
    # ut. Set to 0 to select lane3 ref clock mux output.
		# PSU_SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL                                 0x0

		# Bit 1 of lane 3 ref clock mux one hot sel. Set to 1 to select lane 1 sli
    # cer output from ref clock network
		# PSU_SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1                                   0x1

		# Lane3 Ref Clock Selection Register
		#(OFFSET, MASK, VALUE)      (0XFD40286C, 0x00000082U ,0x00000002U)  */
    mask_write 0XFD40286C 0x00000082 0x00000002
		# : ENABLE SPREAD SPECTRUM
		# Register : L2_TM_PLL_DIG_37 @ 0XFD40A094</p>

		# Enable/Disable coarse code satureation limiting logic
		# PSU_SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION                         0x1

		# Test mode register 37
		#(OFFSET, MASK, VALUE)      (0XFD40A094, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD40A094 0x00000010 0x00000010
		# Register : L2_PLL_SS_STEPS_0_LSB @ 0XFD40A368</p>

		# Spread Spectrum No of Steps [7:0]
		# PSU_SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB                          0x38

		# Spread Spectrum No of Steps bits 7:0
		#(OFFSET, MASK, VALUE)      (0XFD40A368, 0x000000FFU ,0x00000038U)  */
    mask_write 0XFD40A368 0x000000FF 0x00000038
		# Register : L2_PLL_SS_STEPS_1_MSB @ 0XFD40A36C</p>

		# Spread Spectrum No of Steps [10:8]
		# PSU_SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB                          0x03

		# Spread Spectrum No of Steps bits 10:8
		#(OFFSET, MASK, VALUE)      (0XFD40A36C, 0x00000007U ,0x00000003U)  */
    mask_write 0XFD40A36C 0x00000007 0x00000003
		# Register : L3_PLL_SS_STEPS_0_LSB @ 0XFD40E368</p>

		# Spread Spectrum No of Steps [7:0]
		# PSU_SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB                          0xE0

		# Spread Spectrum No of Steps bits 7:0
		#(OFFSET, MASK, VALUE)      (0XFD40E368, 0x000000FFU ,0x000000E0U)  */
    mask_write 0XFD40E368 0x000000FF 0x000000E0
		# Register : L3_PLL_SS_STEPS_1_MSB @ 0XFD40E36C</p>

		# Spread Spectrum No of Steps [10:8]
		# PSU_SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB                          0x3

		# Spread Spectrum No of Steps bits 10:8
		#(OFFSET, MASK, VALUE)      (0XFD40E36C, 0x00000007U ,0x00000003U)  */
    mask_write 0XFD40E36C 0x00000007 0x00000003
		# Register : L1_PLL_SS_STEPS_0_LSB @ 0XFD406368</p>

		# Spread Spectrum No of Steps [7:0]
		# PSU_SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB                          0x58

		# Spread Spectrum No of Steps bits 7:0
		#(OFFSET, MASK, VALUE)      (0XFD406368, 0x000000FFU ,0x00000058U)  */
    mask_write 0XFD406368 0x000000FF 0x00000058
		# Register : L1_PLL_SS_STEPS_1_MSB @ 0XFD40636C</p>

		# Spread Spectrum No of Steps [10:8]
		# PSU_SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB                          0x3

		# Spread Spectrum No of Steps bits 10:8
		#(OFFSET, MASK, VALUE)      (0XFD40636C, 0x00000007U ,0x00000003U)  */
    mask_write 0XFD40636C 0x00000007 0x00000003
		# Register : L1_PLL_SS_STEP_SIZE_0_LSB @ 0XFD406370</p>

		# Step Size for Spread Spectrum [7:0]
		# PSU_SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB                         0x7C

		# Step Size for Spread Spectrum LSB
		#(OFFSET, MASK, VALUE)      (0XFD406370, 0x000000FFU ,0x0000007CU)  */
    mask_write 0XFD406370 0x000000FF 0x0000007C
		# Register : L1_PLL_SS_STEP_SIZE_1 @ 0XFD406374</p>

		# Step Size for Spread Spectrum [15:8]
		# PSU_SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1                                 0x33

		# Step Size for Spread Spectrum 1
		#(OFFSET, MASK, VALUE)      (0XFD406374, 0x000000FFU ,0x00000033U)  */
    mask_write 0XFD406374 0x000000FF 0x00000033
		# Register : L1_PLL_SS_STEP_SIZE_2 @ 0XFD406378</p>

		# Step Size for Spread Spectrum [23:16]
		# PSU_SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2                                 0x2

		# Step Size for Spread Spectrum 2
		#(OFFSET, MASK, VALUE)      (0XFD406378, 0x000000FFU ,0x00000002U)  */
    mask_write 0XFD406378 0x000000FF 0x00000002
		# Register : L1_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40637C</p>

		# Step Size for Spread Spectrum [25:24]
		# PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB                         0x0

		# Enable/Disable test mode force on SS step size
		# PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE                         0x1

		# Enable/Disable test mode force on SS no of steps
		# PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS                      0x1

		# Enable force on enable Spread Spectrum
		#(OFFSET, MASK, VALUE)      (0XFD40637C, 0x00000033U ,0x00000030U)  */
    mask_write 0XFD40637C 0x00000033 0x00000030
		# Register : L2_PLL_SS_STEP_SIZE_0_LSB @ 0XFD40A370</p>

		# Step Size for Spread Spectrum [7:0]
		# PSU_SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB                         0xF4

		# Step Size for Spread Spectrum LSB
		#(OFFSET, MASK, VALUE)      (0XFD40A370, 0x000000FFU ,0x000000F4U)  */
    mask_write 0XFD40A370 0x000000FF 0x000000F4
		# Register : L2_PLL_SS_STEP_SIZE_1 @ 0XFD40A374</p>

		# Step Size for Spread Spectrum [15:8]
		# PSU_SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1                                 0x31

		# Step Size for Spread Spectrum 1
		#(OFFSET, MASK, VALUE)      (0XFD40A374, 0x000000FFU ,0x00000031U)  */
    mask_write 0XFD40A374 0x000000FF 0x00000031
		# Register : L2_PLL_SS_STEP_SIZE_2 @ 0XFD40A378</p>

		# Step Size for Spread Spectrum [23:16]
		# PSU_SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2                                 0x2

		# Step Size for Spread Spectrum 2
		#(OFFSET, MASK, VALUE)      (0XFD40A378, 0x000000FFU ,0x00000002U)  */
    mask_write 0XFD40A378 0x000000FF 0x00000002
		# Register : L2_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40A37C</p>

		# Step Size for Spread Spectrum [25:24]
		# PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB                         0x0

		# Enable/Disable test mode force on SS step size
		# PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE                         0x1

		# Enable/Disable test mode force on SS no of steps
		# PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS                      0x1

		# Enable force on enable Spread Spectrum
		#(OFFSET, MASK, VALUE)      (0XFD40A37C, 0x00000033U ,0x00000030U)  */
    mask_write 0XFD40A37C 0x00000033 0x00000030
		# Register : L3_PLL_SS_STEP_SIZE_0_LSB @ 0XFD40E370</p>

		# Step Size for Spread Spectrum [7:0]
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB                         0xC9

		# Step Size for Spread Spectrum LSB
		#(OFFSET, MASK, VALUE)      (0XFD40E370, 0x000000FFU ,0x000000C9U)  */
    mask_write 0XFD40E370 0x000000FF 0x000000C9
		# Register : L3_PLL_SS_STEP_SIZE_1 @ 0XFD40E374</p>

		# Step Size for Spread Spectrum [15:8]
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1                                 0xD2

		# Step Size for Spread Spectrum 1
		#(OFFSET, MASK, VALUE)      (0XFD40E374, 0x000000FFU ,0x000000D2U)  */
    mask_write 0XFD40E374 0x000000FF 0x000000D2
		# Register : L3_PLL_SS_STEP_SIZE_2 @ 0XFD40E378</p>

		# Step Size for Spread Spectrum [23:16]
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2                                 0x1

		# Step Size for Spread Spectrum 2
		#(OFFSET, MASK, VALUE)      (0XFD40E378, 0x000000FFU ,0x00000001U)  */
    mask_write 0XFD40E378 0x000000FF 0x00000001
		# Register : L3_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40E37C</p>

		# Step Size for Spread Spectrum [25:24]
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB                         0x0

		# Enable/Disable test mode force on SS step size
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE                         0x1

		# Enable/Disable test mode force on SS no of steps
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS                      0x1

		# Enable test mode forcing on enable Spread Spectrum
		# PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS                             0x1

		# Enable force on enable Spread Spectrum
		#(OFFSET, MASK, VALUE)      (0XFD40E37C, 0x000000B3U ,0x000000B0U)  */
    mask_write 0XFD40E37C 0x000000B3 0x000000B0
		# Register : L2_TM_DIG_6 @ 0XFD40906C</p>

		# Bypass Descrambler
		# PSU_SERDES_L2_TM_DIG_6_BYPASS_DESCRAM                                           0x1

		# Enable Bypass for <1> TM_DIG_CTRL_6
		# PSU_SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM                                     0x1

		# Data path test modes in decoder and descram
		#(OFFSET, MASK, VALUE)      (0XFD40906C, 0x00000003U ,0x00000003U)  */
    mask_write 0XFD40906C 0x00000003 0x00000003
		# Register : L2_TX_DIG_TM_61 @ 0XFD4080F4</p>

		# Bypass scrambler signal
		# PSU_SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM                                         0x1

		# Enable/disable scrambler bypass signal
		# PSU_SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM                                   0x1

		# MPHY PLL Gear and bypass scrambler
		#(OFFSET, MASK, VALUE)      (0XFD4080F4, 0x00000003U ,0x00000003U)  */
    mask_write 0XFD4080F4 0x00000003 0x00000003
		# Register : L3_PLL_FBDIV_FRAC_3_MSB @ 0XFD40E360</p>

		# Enable test mode force on fractional mode enable
		# PSU_SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC                             0x1

		# Fractional feedback division control and fractional value for feedback d
    # ivision bits 26:24
		#(OFFSET, MASK, VALUE)      (0XFD40E360, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40E360 0x00000040 0x00000040
		# Register : L3_TM_DIG_6 @ 0XFD40D06C</p>

		# Bypass 8b10b decoder
		# PSU_SERDES_L3_TM_DIG_6_BYPASS_DECODER                                           0x1

		# Enable Bypass for <3> TM_DIG_CTRL_6
		# PSU_SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC                                         0x1

		# Bypass Descrambler
		# PSU_SERDES_L3_TM_DIG_6_BYPASS_DESCRAM                                           0x1

		# Enable Bypass for <1> TM_DIG_CTRL_6
		# PSU_SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM                                     0x1

		# Data path test modes in decoder and descram
		#(OFFSET, MASK, VALUE)      (0XFD40D06C, 0x0000000FU ,0x0000000FU)  */
    mask_write 0XFD40D06C 0x0000000F 0x0000000F
		# Register : L3_TX_DIG_TM_61 @ 0XFD40C0F4</p>

		# Enable/disable encoder bypass signal
		# PSU_SERDES_L3_TX_DIG_TM_61_BYPASS_ENC                                           0x1

		# Bypass scrambler signal
		# PSU_SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM                                         0x1

		# Enable/disable scrambler bypass signal
		# PSU_SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM                                   0x1

		# MPHY PLL Gear and bypass scrambler
		#(OFFSET, MASK, VALUE)      (0XFD40C0F4, 0x0000000BU ,0x0000000BU)  */
    mask_write 0XFD40C0F4 0x0000000B 0x0000000B
		# : ENABLE CHICKEN BIT FOR PCIE AND USB
		# Register : L0_TM_AUX_0 @ 0XFD4010CC</p>

		# Spare- not used
		# PSU_SERDES_L0_TM_AUX_0_BIT_2                                                    1

		# Spare registers
		#(OFFSET, MASK, VALUE)      (0XFD4010CC, 0x00000020U ,0x00000020U)  */
    mask_write 0XFD4010CC 0x00000020 0x00000020
		# Register : L2_TM_AUX_0 @ 0XFD4090CC</p>

		# Spare- not used
		# PSU_SERDES_L2_TM_AUX_0_BIT_2                                                    1

		# Spare registers
		#(OFFSET, MASK, VALUE)      (0XFD4090CC, 0x00000020U ,0x00000020U)  */
    mask_write 0XFD4090CC 0x00000020 0x00000020
		# : ENABLING EYE SURF
		# Register : L0_TM_DIG_8 @ 0XFD401074</p>

		# Enable Eye Surf
		# PSU_SERDES_L0_TM_DIG_8_EYESURF_ENABLE                                           0x1

		# Test modes for Elastic buffer and enabling Eye Surf
		#(OFFSET, MASK, VALUE)      (0XFD401074, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD401074 0x00000010 0x00000010
		# Register : L1_TM_DIG_8 @ 0XFD405074</p>

		# Enable Eye Surf
		# PSU_SERDES_L1_TM_DIG_8_EYESURF_ENABLE                                           0x1

		# Test modes for Elastic buffer and enabling Eye Surf
		#(OFFSET, MASK, VALUE)      (0XFD405074, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD405074 0x00000010 0x00000010
		# Register : L2_TM_DIG_8 @ 0XFD409074</p>

		# Enable Eye Surf
		# PSU_SERDES_L2_TM_DIG_8_EYESURF_ENABLE                                           0x1

		# Test modes for Elastic buffer and enabling Eye Surf
		#(OFFSET, MASK, VALUE)      (0XFD409074, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD409074 0x00000010 0x00000010
		# Register : L3_TM_DIG_8 @ 0XFD40D074</p>

		# Enable Eye Surf
		# PSU_SERDES_L3_TM_DIG_8_EYESURF_ENABLE                                           0x1

		# Test modes for Elastic buffer and enabling Eye Surf
		#(OFFSET, MASK, VALUE)      (0XFD40D074, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD40D074 0x00000010 0x00000010
		# : ILL SETTINGS FOR GAIN AND LOCK SETTINGS
		# Register : L0_TM_MISC2 @ 0XFD40189C</p>

		# ILL calib counts BYPASSED with calcode bits
		# PSU_SERDES_L0_TM_MISC2_ILL_CAL_BYPASS_COUNTS                                    0x1

		# sampler cal
		#(OFFSET, MASK, VALUE)      (0XFD40189C, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD40189C 0x00000080 0x00000080
		# Register : L0_TM_IQ_ILL1 @ 0XFD4018F8</p>

		# IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 ,
    # USB3 : SS
		# PSU_SERDES_L0_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0                               0x64

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD4018F8, 0x000000FFU ,0x00000064U)  */
    mask_write 0XFD4018F8 0x000000FF 0x00000064
		# Register : L0_TM_IQ_ILL2 @ 0XFD4018FC</p>

		# IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2
		# PSU_SERDES_L0_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1                               0x64

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD4018FC, 0x000000FFU ,0x00000064U)  */
    mask_write 0XFD4018FC 0x000000FF 0x00000064
		# Register : L0_TM_ILL12 @ 0XFD401990</p>

		# G1A pll ctr bypass value
		# PSU_SERDES_L0_TM_ILL12_G1A_PLL_CTR_BYP_VAL                                      0x11

		# ill pll counter values
		#(OFFSET, MASK, VALUE)      (0XFD401990, 0x000000FFU ,0x00000011U)  */
    mask_write 0XFD401990 0x000000FF 0x00000011
		# Register : L0_TM_E_ILL1 @ 0XFD401924</p>

		# E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , U
    # SB3 : SS
		# PSU_SERDES_L0_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0                                 0x4

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD401924, 0x000000FFU ,0x00000004U)  */
    mask_write 0XFD401924 0x000000FF 0x00000004
		# Register : L0_TM_E_ILL2 @ 0XFD401928</p>

		# E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2
		# PSU_SERDES_L0_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1                                 0xFE

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD401928, 0x000000FFU ,0x000000FEU)  */
    mask_write 0XFD401928 0x000000FF 0x000000FE
		# Register : L0_TM_IQ_ILL3 @ 0XFD401900</p>

		# IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3
		# PSU_SERDES_L0_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2                               0x64

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD401900, 0x000000FFU ,0x00000064U)  */
    mask_write 0XFD401900 0x000000FF 0x00000064
		# Register : L0_TM_E_ILL3 @ 0XFD40192C</p>

		# E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3
		# PSU_SERDES_L0_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2                                 0x0

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40192C, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD40192C 0x000000FF 0x00000000
		# Register : L0_TM_ILL8 @ 0XFD401980</p>

		# ILL calibration code change wait time
		# PSU_SERDES_L0_TM_ILL8_ILL_CAL_ITER_WAIT                                         0xFF

		# ILL cal routine control
		#(OFFSET, MASK, VALUE)      (0XFD401980, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD401980 0x000000FF 0x000000FF
		# Register : L0_TM_IQ_ILL8 @ 0XFD401914</p>

		# IQ ILL polytrim bypass value
		# PSU_SERDES_L0_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL                             0xF7

		# iqpi polytrim
		#(OFFSET, MASK, VALUE)      (0XFD401914, 0x000000FFU ,0x000000F7U)  */
    mask_write 0XFD401914 0x000000FF 0x000000F7
		# Register : L0_TM_IQ_ILL9 @ 0XFD401918</p>

		# bypass IQ polytrim
		# PSU_SERDES_L0_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM                                  0x1

		# enables for lf,constant gm trim and polytirm
		#(OFFSET, MASK, VALUE)      (0XFD401918, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD401918 0x00000001 0x00000001
		# Register : L0_TM_E_ILL8 @ 0XFD401940</p>

		# E ILL polytrim bypass value
		# PSU_SERDES_L0_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL                               0xF7

		# epi polytrim
		#(OFFSET, MASK, VALUE)      (0XFD401940, 0x000000FFU ,0x000000F7U)  */
    mask_write 0XFD401940 0x000000FF 0x000000F7
		# Register : L0_TM_E_ILL9 @ 0XFD401944</p>

		# bypass E polytrim
		# PSU_SERDES_L0_TM_E_ILL9_ILL_BYPASS_E_POLYTIM                                    0x1

		# enables for lf,constant gm trim and polytirm
		#(OFFSET, MASK, VALUE)      (0XFD401944, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD401944 0x00000001 0x00000001
		# Register : L0_TM_ILL13 @ 0XFD401994</p>

		# ILL cal idle val refcnt
		# PSU_SERDES_L0_TM_ILL13_ILL_CAL_IDLE_VAL_REFCNT                                  0x7

		# ill cal idle value count
		#(OFFSET, MASK, VALUE)      (0XFD401994, 0x00000007U ,0x00000007U)  */
    mask_write 0XFD401994 0x00000007 0x00000007
		# Register : L1_TM_ILL13 @ 0XFD405994</p>

		# ILL cal idle val refcnt
		# PSU_SERDES_L1_TM_ILL13_ILL_CAL_IDLE_VAL_REFCNT                                  0x7

		# ill cal idle value count
		#(OFFSET, MASK, VALUE)      (0XFD405994, 0x00000007U ,0x00000007U)  */
    mask_write 0XFD405994 0x00000007 0x00000007
		# Register : L2_TM_MISC2 @ 0XFD40989C</p>

		# ILL calib counts BYPASSED with calcode bits
		# PSU_SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS                                    0x1

		# sampler cal
		#(OFFSET, MASK, VALUE)      (0XFD40989C, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD40989C 0x00000080 0x00000080
		# Register : L2_TM_IQ_ILL1 @ 0XFD4098F8</p>

		# IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 ,
    # USB3 : SS
		# PSU_SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0                               0x1A

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD4098F8, 0x000000FFU ,0x0000001AU)  */
    mask_write 0XFD4098F8 0x000000FF 0x0000001A
		# Register : L2_TM_IQ_ILL2 @ 0XFD4098FC</p>

		# IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2
		# PSU_SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1                               0x1A

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD4098FC, 0x000000FFU ,0x0000001AU)  */
    mask_write 0XFD4098FC 0x000000FF 0x0000001A
		# Register : L2_TM_ILL12 @ 0XFD409990</p>

		# G1A pll ctr bypass value
		# PSU_SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL                                      0x10

		# ill pll counter values
		#(OFFSET, MASK, VALUE)      (0XFD409990, 0x000000FFU ,0x00000010U)  */
    mask_write 0XFD409990 0x000000FF 0x00000010
		# Register : L2_TM_E_ILL1 @ 0XFD409924</p>

		# E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , U
    # SB3 : SS
		# PSU_SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0                                 0xFE

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD409924, 0x000000FFU ,0x000000FEU)  */
    mask_write 0XFD409924 0x000000FF 0x000000FE
		# Register : L2_TM_E_ILL2 @ 0XFD409928</p>

		# E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2
		# PSU_SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1                                 0x0

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD409928, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD409928 0x000000FF 0x00000000
		# Register : L2_TM_IQ_ILL3 @ 0XFD409900</p>

		# IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3
		# PSU_SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2                               0x1A

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD409900, 0x000000FFU ,0x0000001AU)  */
    mask_write 0XFD409900 0x000000FF 0x0000001A
		# Register : L2_TM_E_ILL3 @ 0XFD40992C</p>

		# E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3
		# PSU_SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2                                 0x0

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40992C, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD40992C 0x000000FF 0x00000000
		# Register : L2_TM_ILL8 @ 0XFD409980</p>

		# ILL calibration code change wait time
		# PSU_SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT                                         0xFF

		# ILL cal routine control
		#(OFFSET, MASK, VALUE)      (0XFD409980, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD409980 0x000000FF 0x000000FF
		# Register : L2_TM_IQ_ILL8 @ 0XFD409914</p>

		# IQ ILL polytrim bypass value
		# PSU_SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL                             0xF7

		# iqpi polytrim
		#(OFFSET, MASK, VALUE)      (0XFD409914, 0x000000FFU ,0x000000F7U)  */
    mask_write 0XFD409914 0x000000FF 0x000000F7
		# Register : L2_TM_IQ_ILL9 @ 0XFD409918</p>

		# bypass IQ polytrim
		# PSU_SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM                                  0x1

		# enables for lf,constant gm trim and polytirm
		#(OFFSET, MASK, VALUE)      (0XFD409918, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD409918 0x00000001 0x00000001
		# Register : L2_TM_E_ILL8 @ 0XFD409940</p>

		# E ILL polytrim bypass value
		# PSU_SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL                               0xF7

		# epi polytrim
		#(OFFSET, MASK, VALUE)      (0XFD409940, 0x000000FFU ,0x000000F7U)  */
    mask_write 0XFD409940 0x000000FF 0x000000F7
		# Register : L2_TM_E_ILL9 @ 0XFD409944</p>

		# bypass E polytrim
		# PSU_SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM                                    0x1

		# enables for lf,constant gm trim and polytirm
		#(OFFSET, MASK, VALUE)      (0XFD409944, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD409944 0x00000001 0x00000001
		# Register : L2_TM_ILL13 @ 0XFD409994</p>

		# ILL cal idle val refcnt
		# PSU_SERDES_L2_TM_ILL13_ILL_CAL_IDLE_VAL_REFCNT                                  0x7

		# ill cal idle value count
		#(OFFSET, MASK, VALUE)      (0XFD409994, 0x00000007U ,0x00000007U)  */
    mask_write 0XFD409994 0x00000007 0x00000007
		# Register : L3_TM_MISC2 @ 0XFD40D89C</p>

		# ILL calib counts BYPASSED with calcode bits
		# PSU_SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS                                    0x1

		# sampler cal
		#(OFFSET, MASK, VALUE)      (0XFD40D89C, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD40D89C 0x00000080 0x00000080
		# Register : L3_TM_IQ_ILL1 @ 0XFD40D8F8</p>

		# IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 ,
    # USB3 : SS
		# PSU_SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0                               0x7D

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40D8F8, 0x000000FFU ,0x0000007DU)  */
    mask_write 0XFD40D8F8 0x000000FF 0x0000007D
		# Register : L3_TM_IQ_ILL2 @ 0XFD40D8FC</p>

		# IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2
		# PSU_SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1                               0x7D

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40D8FC, 0x000000FFU ,0x0000007DU)  */
    mask_write 0XFD40D8FC 0x000000FF 0x0000007D
		# Register : L3_TM_ILL12 @ 0XFD40D990</p>

		# G1A pll ctr bypass value
		# PSU_SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL                                      0x1

		# ill pll counter values
		#(OFFSET, MASK, VALUE)      (0XFD40D990, 0x000000FFU ,0x00000001U)  */
    mask_write 0XFD40D990 0x000000FF 0x00000001
		# Register : L3_TM_E_ILL1 @ 0XFD40D924</p>

		# E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , U
    # SB3 : SS
		# PSU_SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0                                 0x9C

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40D924, 0x000000FFU ,0x0000009CU)  */
    mask_write 0XFD40D924 0x000000FF 0x0000009C
		# Register : L3_TM_E_ILL2 @ 0XFD40D928</p>

		# E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2
		# PSU_SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1                                 0x39

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40D928, 0x000000FFU ,0x00000039U)  */
    mask_write 0XFD40D928 0x000000FF 0x00000039
		# Register : L3_TM_ILL11 @ 0XFD40D98C</p>

		# G2A_PCIe1 PLL ctr bypass value
		# PSU_SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL                          0x2

		# ill pll counter values
		#(OFFSET, MASK, VALUE)      (0XFD40D98C, 0x000000F0U ,0x00000020U)  */
    mask_write 0XFD40D98C 0x000000F0 0x00000020
		# Register : L3_TM_IQ_ILL3 @ 0XFD40D900</p>

		# IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3
		# PSU_SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2                               0x7D

		# iqpi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40D900, 0x000000FFU ,0x0000007DU)  */
    mask_write 0XFD40D900 0x000000FF 0x0000007D
		# Register : L3_TM_E_ILL3 @ 0XFD40D92C</p>

		# E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3
		# PSU_SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2                                 0x64

		# epi cal code
		#(OFFSET, MASK, VALUE)      (0XFD40D92C, 0x000000FFU ,0x00000064U)  */
    mask_write 0XFD40D92C 0x000000FF 0x00000064
		# Register : L3_TM_ILL8 @ 0XFD40D980</p>

		# ILL calibration code change wait time
		# PSU_SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT                                         0xFF

		# ILL cal routine control
		#(OFFSET, MASK, VALUE)      (0XFD40D980, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD40D980 0x000000FF 0x000000FF
		# Register : L3_TM_IQ_ILL8 @ 0XFD40D914</p>

		# IQ ILL polytrim bypass value
		# PSU_SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL                             0xF7

		# iqpi polytrim
		#(OFFSET, MASK, VALUE)      (0XFD40D914, 0x000000FFU ,0x000000F7U)  */
    mask_write 0XFD40D914 0x000000FF 0x000000F7
		# Register : L3_TM_IQ_ILL9 @ 0XFD40D918</p>

		# bypass IQ polytrim
		# PSU_SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM                                  0x1

		# enables for lf,constant gm trim and polytirm
		#(OFFSET, MASK, VALUE)      (0XFD40D918, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD40D918 0x00000001 0x00000001
		# Register : L3_TM_E_ILL8 @ 0XFD40D940</p>

		# E ILL polytrim bypass value
		# PSU_SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL                               0xF7

		# epi polytrim
		#(OFFSET, MASK, VALUE)      (0XFD40D940, 0x000000FFU ,0x000000F7U)  */
    mask_write 0XFD40D940 0x000000FF 0x000000F7
		# Register : L3_TM_E_ILL9 @ 0XFD40D944</p>

		# bypass E polytrim
		# PSU_SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM                                    0x1

		# enables for lf,constant gm trim and polytirm
		#(OFFSET, MASK, VALUE)      (0XFD40D944, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD40D944 0x00000001 0x00000001
		# Register : L3_TM_ILL13 @ 0XFD40D994</p>

		# ILL cal idle val refcnt
		# PSU_SERDES_L3_TM_ILL13_ILL_CAL_IDLE_VAL_REFCNT                                  0x7

		# ill cal idle value count
		#(OFFSET, MASK, VALUE)      (0XFD40D994, 0x00000007U ,0x00000007U)  */
    mask_write 0XFD40D994 0x00000007 0x00000007
		# : SYMBOL LOCK AND WAIT
		# Register : L0_TM_DIG_10 @ 0XFD40107C</p>

		# CDR lock wait time. (1-16 us). cdr_lock_wait_time = 4'b xxxx + 4'b 0001
		# PSU_SERDES_L0_TM_DIG_10_CDR_BIT_LOCK_TIME                                       0x1

		# test control for changing cdr lock wait time
		#(OFFSET, MASK, VALUE)      (0XFD40107C, 0x0000000FU ,0x00000001U)  */
    mask_write 0XFD40107C 0x0000000F 0x00000001
		# Register : L1_TM_DIG_10 @ 0XFD40507C</p>

		# CDR lock wait time. (1-16 us). cdr_lock_wait_time = 4'b xxxx + 4'b 0001
		# PSU_SERDES_L1_TM_DIG_10_CDR_BIT_LOCK_TIME                                       0x1

		# test control for changing cdr lock wait time
		#(OFFSET, MASK, VALUE)      (0XFD40507C, 0x0000000FU ,0x00000001U)  */
    mask_write 0XFD40507C 0x0000000F 0x00000001
		# Register : L2_TM_DIG_10 @ 0XFD40907C</p>

		# CDR lock wait time. (1-16 us). cdr_lock_wait_time = 4'b xxxx + 4'b 0001
		# PSU_SERDES_L2_TM_DIG_10_CDR_BIT_LOCK_TIME                                       0x1

		# test control for changing cdr lock wait time
		#(OFFSET, MASK, VALUE)      (0XFD40907C, 0x0000000FU ,0x00000001U)  */
    mask_write 0XFD40907C 0x0000000F 0x00000001
		# Register : L3_TM_DIG_10 @ 0XFD40D07C</p>

		# CDR lock wait time. (1-16 us). cdr_lock_wait_time = 4'b xxxx + 4'b 0001
		# PSU_SERDES_L3_TM_DIG_10_CDR_BIT_LOCK_TIME                                       0x1

		# test control for changing cdr lock wait time
		#(OFFSET, MASK, VALUE)      (0XFD40D07C, 0x0000000FU ,0x00000001U)  */
    mask_write 0XFD40D07C 0x0000000F 0x00000001
		# : SIOU SETTINGS FOR BYPASS CONTROL,HSRX-DIG
		# Register : L0_TM_RST_DLY @ 0XFD4019A4</p>

		# Delay apb reset by specified amount
		# PSU_SERDES_L0_TM_RST_DLY_APB_RST_DLY                                            0xFF

		# reset delay for apb reset w.r.t pso of hsrx
		#(OFFSET, MASK, VALUE)      (0XFD4019A4, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD4019A4 0x000000FF 0x000000FF
		# Register : L0_TM_ANA_BYP_15 @ 0XFD401038</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_15
		# PSU_SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE                       0x1

		# Bypass control for pcs-pma interface. EQ supplies, main master supply an
    # d ps for samp c2c
		#(OFFSET, MASK, VALUE)      (0XFD401038, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD401038 0x00000040 0x00000040
		# Register : L0_TM_ANA_BYP_12 @ 0XFD40102C</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_12
		# PSU_SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG                              0x1

		# Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr ena
    # ble controls
		#(OFFSET, MASK, VALUE)      (0XFD40102C, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40102C 0x00000040 0x00000040
		# Register : L1_TM_RST_DLY @ 0XFD4059A4</p>

		# Delay apb reset by specified amount
		# PSU_SERDES_L1_TM_RST_DLY_APB_RST_DLY                                            0xFF

		# reset delay for apb reset w.r.t pso of hsrx
		#(OFFSET, MASK, VALUE)      (0XFD4059A4, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD4059A4 0x000000FF 0x000000FF
		# Register : L1_TM_ANA_BYP_15 @ 0XFD405038</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_15
		# PSU_SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE                       0x1

		# Bypass control for pcs-pma interface. EQ supplies, main master supply an
    # d ps for samp c2c
		#(OFFSET, MASK, VALUE)      (0XFD405038, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD405038 0x00000040 0x00000040
		# Register : L1_TM_ANA_BYP_12 @ 0XFD40502C</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_12
		# PSU_SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG                              0x1

		# Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr ena
    # ble controls
		#(OFFSET, MASK, VALUE)      (0XFD40502C, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40502C 0x00000040 0x00000040
		# Register : L2_TM_RST_DLY @ 0XFD4099A4</p>

		# Delay apb reset by specified amount
		# PSU_SERDES_L2_TM_RST_DLY_APB_RST_DLY                                            0xFF

		# reset delay for apb reset w.r.t pso of hsrx
		#(OFFSET, MASK, VALUE)      (0XFD4099A4, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD4099A4 0x000000FF 0x000000FF
		# Register : L2_TM_ANA_BYP_15 @ 0XFD409038</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_15
		# PSU_SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE                       0x1

		# Bypass control for pcs-pma interface. EQ supplies, main master supply an
    # d ps for samp c2c
		#(OFFSET, MASK, VALUE)      (0XFD409038, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD409038 0x00000040 0x00000040
		# Register : L2_TM_ANA_BYP_12 @ 0XFD40902C</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_12
		# PSU_SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG                              0x1

		# Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr ena
    # ble controls
		#(OFFSET, MASK, VALUE)      (0XFD40902C, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40902C 0x00000040 0x00000040
		# Register : L3_TM_RST_DLY @ 0XFD40D9A4</p>

		# Delay apb reset by specified amount
		# PSU_SERDES_L3_TM_RST_DLY_APB_RST_DLY                                            0xFF

		# reset delay for apb reset w.r.t pso of hsrx
		#(OFFSET, MASK, VALUE)      (0XFD40D9A4, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFD40D9A4 0x000000FF 0x000000FF
		# Register : L3_TM_ANA_BYP_15 @ 0XFD40D038</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_15
		# PSU_SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE                       0x1

		# Bypass control for pcs-pma interface. EQ supplies, main master supply an
    # d ps for samp c2c
		#(OFFSET, MASK, VALUE)      (0XFD40D038, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40D038 0x00000040 0x00000040
		# Register : L3_TM_ANA_BYP_12 @ 0XFD40D02C</p>

		# Enable Bypass for <7> of TM_ANA_BYPS_12
		# PSU_SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG                              0x1

		# Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr ena
    # ble controls
		#(OFFSET, MASK, VALUE)      (0XFD40D02C, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40D02C 0x00000040 0x00000040
		# : DISABLE FPL/FFL
		# Register : L0_TM_MISC3 @ 0XFD4019AC</p>

		# CDR fast phase lock control
		# PSU_SERDES_L0_TM_MISC3_CDR_EN_FPL                                               0x0

		# CDR fast frequency lock control
		# PSU_SERDES_L0_TM_MISC3_CDR_EN_FFL                                               0x0

		# debug bus selection bit, cdr fast phase and freq controls
		#(OFFSET, MASK, VALUE)      (0XFD4019AC, 0x00000003U ,0x00000000U)  */
    mask_write 0XFD4019AC 0x00000003 0x00000000
		# Register : L1_TM_MISC3 @ 0XFD4059AC</p>

		# CDR fast phase lock control
		# PSU_SERDES_L1_TM_MISC3_CDR_EN_FPL                                               0x0

		# CDR fast frequency lock control
		# PSU_SERDES_L1_TM_MISC3_CDR_EN_FFL                                               0x0

		# debug bus selection bit, cdr fast phase and freq controls
		#(OFFSET, MASK, VALUE)      (0XFD4059AC, 0x00000003U ,0x00000000U)  */
    mask_write 0XFD4059AC 0x00000003 0x00000000
		# Register : L2_TM_MISC3 @ 0XFD4099AC</p>

		# CDR fast phase lock control
		# PSU_SERDES_L2_TM_MISC3_CDR_EN_FPL                                               0x0

		# CDR fast frequency lock control
		# PSU_SERDES_L2_TM_MISC3_CDR_EN_FFL                                               0x0

		# debug bus selection bit, cdr fast phase and freq controls
		#(OFFSET, MASK, VALUE)      (0XFD4099AC, 0x00000003U ,0x00000000U)  */
    mask_write 0XFD4099AC 0x00000003 0x00000000
		# Register : L3_TM_MISC3 @ 0XFD40D9AC</p>

		# CDR fast phase lock control
		# PSU_SERDES_L3_TM_MISC3_CDR_EN_FPL                                               0x0

		# CDR fast frequency lock control
		# PSU_SERDES_L3_TM_MISC3_CDR_EN_FFL                                               0x0

		# debug bus selection bit, cdr fast phase and freq controls
		#(OFFSET, MASK, VALUE)      (0XFD40D9AC, 0x00000003U ,0x00000000U)  */
    mask_write 0XFD40D9AC 0x00000003 0x00000000
		# : DISABLE DYNAMIC OFFSET CALIBRATION
		# Register : L0_TM_EQ11 @ 0XFD401978</p>

		# Force EQ offset correction algo off if not forced on
		# PSU_SERDES_L0_TM_EQ11_FORCE_EQ_OFFS_OFF                                         0x1

		# eq dynamic offset correction
		#(OFFSET, MASK, VALUE)      (0XFD401978, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD401978 0x00000010 0x00000010
		# Register : L1_TM_EQ11 @ 0XFD405978</p>

		# Force EQ offset correction algo off if not forced on
		# PSU_SERDES_L1_TM_EQ11_FORCE_EQ_OFFS_OFF                                         0x1

		# eq dynamic offset correction
		#(OFFSET, MASK, VALUE)      (0XFD405978, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD405978 0x00000010 0x00000010
		# Register : L2_TM_EQ11 @ 0XFD409978</p>

		# Force EQ offset correction algo off if not forced on
		# PSU_SERDES_L2_TM_EQ11_FORCE_EQ_OFFS_OFF                                         0x1

		# eq dynamic offset correction
		#(OFFSET, MASK, VALUE)      (0XFD409978, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD409978 0x00000010 0x00000010
		# Register : L3_TM_EQ11 @ 0XFD40D978</p>

		# Force EQ offset correction algo off if not forced on
		# PSU_SERDES_L3_TM_EQ11_FORCE_EQ_OFFS_OFF                                         0x1

		# eq dynamic offset correction
		#(OFFSET, MASK, VALUE)      (0XFD40D978, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD40D978 0x00000010 0x00000010
		# : DISABLE ECO FOR PCIE
		# Register : eco_0 @ 0XFD3D001C</p>

		# For future use
		# PSU_SIOU_ECO_0_FIELD                                                            0x1

		# ECO Register for future use
		#(OFFSET, MASK, VALUE)      (0XFD3D001C, 0xFFFFFFFFU ,0x00000001U)  */
    mask_write 0XFD3D001C 0xFFFFFFFF 0x00000001
		# : GT LANE SETTINGS
		# Register : ICM_CFG0 @ 0XFD410010</p>

		# Controls UPHY Lane 0 protocol configuration. 0 - PowerDown, 1 - PCIe .0,
    #  2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII0, 6 - Unused, 7 - Unused
		# PSU_SERDES_ICM_CFG0_L0_ICM_CFG                                                  1

		# Controls UPHY Lane 1 protocol configuration. 0 - PowerDown, 1 - PCIe.1,
    # 2 - Sata1, 3 - USB0, 4 - DP.0, 5 - SGMII1, 6 - Unused, 7 - Unused
		# PSU_SERDES_ICM_CFG0_L1_ICM_CFG                                                  4

		# ICM Configuration Register 0
		#(OFFSET, MASK, VALUE)      (0XFD410010, 0x00000077U ,0x00000041U)  */
    mask_write 0XFD410010 0x00000077 0x00000041
		# Register : ICM_CFG1 @ 0XFD410014</p>

		# Controls UPHY Lane 2 protocol configuration. 0 - PowerDown, 1 - PCIe.1,
    # 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII2, 6 - Unused, 7 - Unused
		# PSU_SERDES_ICM_CFG1_L2_ICM_CFG                                                  3

		# Controls UPHY Lane 3 protocol configuration. 0 - PowerDown, 1 - PCIe.3,
    # 2 - Sata1, 3 - USB1, 4 - DP.0, 5 - SGMII3, 6 - Unused, 7 - Unused
		# PSU_SERDES_ICM_CFG1_L3_ICM_CFG                                                  2

		# ICM Configuration Register 1
		#(OFFSET, MASK, VALUE)      (0XFD410014, 0x00000077U ,0x00000023U)  */
    mask_write 0XFD410014 0x00000077 0x00000023
		# : CHECKING PLL LOCK
		# : ENABLE SERIAL DATA MUX DEEMPH
		# Register : L1_TXPMD_TM_45 @ 0XFD404CB4</p>

		# Enable/disable DP post2 path
		# PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH                         0x1

		# Override enable/disable of DP post2 path
		# PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH                    0x1

		# Override enable/disable of DP post1 path
		# PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH                    0x1

		# Enable/disable DP main path
		# PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH                          0x1

		# Override enable/disable of DP main path
		# PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH                     0x1

		# Post or pre or main DP path selection
		#(OFFSET, MASK, VALUE)      (0XFD404CB4, 0x00000037U ,0x00000037U)  */
    mask_write 0XFD404CB4 0x00000037 0x00000037
		# Register : L1_TX_ANA_TM_118 @ 0XFD4041D8</p>

		# Test register force for enabling/disablign TX deemphasis bits <17:0>
		# PSU_SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0                                0x1

		# Enable Override of TX deemphasis
		#(OFFSET, MASK, VALUE)      (0XFD4041D8, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD4041D8 0x00000001 0x00000001
		# Register : L3_TX_ANA_TM_118 @ 0XFD40C1D8</p>

		# Test register force for enabling/disablign TX deemphasis bits <17:0>
		# PSU_SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0                                0x1

		# Enable Override of TX deemphasis
		#(OFFSET, MASK, VALUE)      (0XFD40C1D8, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD40C1D8 0x00000001 0x00000001
		# : CDR AND RX EQUALIZATION SETTINGS
		# Register : L3_TM_CDR5 @ 0XFD40DC14</p>

		# FPHL FSM accumulate cycles
		# PSU_SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES                                       0x7

		# FFL Phase0 int gain aka 2ol SD update rate
		# PSU_SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN                                          0x6

		# Fast phase lock controls -- FSM accumulator cycle control and phase 0 in
    # t gain control.
		#(OFFSET, MASK, VALUE)      (0XFD40DC14, 0x000000FFU ,0x000000E6U)  */
    mask_write 0XFD40DC14 0x000000FF 0x000000E6
		# Register : L3_TM_CDR16 @ 0XFD40DC40</p>

		# FFL Phase0 prop gain aka 1ol SD update rate
		# PSU_SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN                                        0xC

		# Fast phase lock controls -- phase 0 prop gain
		#(OFFSET, MASK, VALUE)      (0XFD40DC40, 0x0000001FU ,0x0000000CU)  */
    mask_write 0XFD40DC40 0x0000001F 0x0000000C
		# Register : L3_TM_EQ0 @ 0XFD40D94C</p>

		# EQ stg 2 controls BYPASSED
		# PSU_SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP                                           1

		# eq stg1 and stg2 controls
		#(OFFSET, MASK, VALUE)      (0XFD40D94C, 0x00000020U ,0x00000020U)  */
    mask_write 0XFD40D94C 0x00000020 0x00000020
		# Register : L3_TM_EQ1 @ 0XFD40D950</p>

		# EQ STG2 RL PROG
		# PSU_SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG                                            0x2

		# EQ stg 2 preamp mode val
		# PSU_SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL                                    0x1

		# eq stg1 and stg2 controls
		#(OFFSET, MASK, VALUE)      (0XFD40D950, 0x00000007U ,0x00000006U)  */
    mask_write 0XFD40D950 0x00000007 0x00000006
		# : GEM SERDES SETTINGS
		# : ENABLE PRE EMPHAIS AND VOLTAGE SWING
		# Register : L1_TXPMD_TM_48 @ 0XFD404CC0</p>

		# Margining factor value
		# PSU_SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR                         0

		# Margining factor
		#(OFFSET, MASK, VALUE)      (0XFD404CC0, 0x0000001FU ,0x00000000U)  */
    mask_write 0XFD404CC0 0x0000001F 0x00000000
		# Register : L1_TX_ANA_TM_18 @ 0XFD404048</p>

		# pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-em
    # phasis, Others: reserved
		# PSU_SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0                                   0

		# Override for PIPE TX de-emphasis
		#(OFFSET, MASK, VALUE)      (0XFD404048, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD404048 0x000000FF 0x00000000
		# Register : L3_TX_ANA_TM_18 @ 0XFD40C048</p>

		# pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-em
    # phasis, Others: reserved
		# PSU_SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0                                   0x1

		# Override for PIPE TX de-emphasis
		#(OFFSET, MASK, VALUE)      (0XFD40C048, 0x000000FFU ,0x00000001U)  */
    mask_write 0XFD40C048 0x000000FF 0x00000001
}

set psu_resetout_init_data {
		# : TAKING SERDES PERIPHERAL OUT OF RESET RESET
		# : PUTTING USB0 IN RESET
		# Register : RST_LPD_TOP @ 0XFF5E023C</p>

		# USB 0 reset for control registers
		# PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET                                          0X0

		# Software control register for the LPD block.
		#(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000400U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00000400 0x00000000
		# : HIBERREST
		# Register : RST_LPD_TOP @ 0XFF5E023C</p>

		# USB 0 sleep circuit reset
		# PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET                                         0X0

		# USB 0 reset
		# PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET                                          0X0

		# Software control register for the LPD block.
		#(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000140U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00000140 0x00000000
		# : PUTTING GEM0 IN RESET
		# Register : RST_LPD_IOU0 @ 0XFF5E0230</p>

		# GEM 3 reset
		# PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET                                             0X0

		# Software controlled reset for the GEMs
		#(OFFSET, MASK, VALUE)      (0XFF5E0230, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0230 0x00000008 0x00000000
		# : PUTTING SATA IN RESET
		# Register : sata_misc_ctrl @ 0XFD3D0100</p>

		# Sata PM clock control select
		# PSU_SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL                                         0x3

		# Misc Contorls for SATA.This register may only be modified during bootup
    # (while SATA block is disabled)
		#(OFFSET, MASK, VALUE)      (0XFD3D0100, 0x00000003U ,0x00000003U)  */
    mask_write 0XFD3D0100 0x00000003 0x00000003
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# Sata block level reset
		# PSU_CRF_APB_RST_FPD_TOP_SATA_RESET                                              0X0

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00000002U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x00000002 0x00000000
		# : PUTTING PCIE CFG AND BRIDGE IN RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# PCIE config reset
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_CFG_RESET                                          0X0

		# PCIE bridge block level reset (AXI interface)
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_BRIDGE_RESET                                       0X0

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x000C0000U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x000C0000 0x00000000
		# : PUTTING DP IN RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# Display Port block level reset (includes DPDMA)
		# PSU_CRF_APB_RST_FPD_TOP_DP_RESET                                                0X0

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00010000U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x00010000 0x00000000
		# Register : DP_PHY_RESET @ 0XFD4A0200</p>

		# Set to '1' to hold the GT in reset. Clear to release.
		# PSU_DP_DP_PHY_RESET_GT_RESET                                                    0X0

		# Reset the transmitter PHY.
		#(OFFSET, MASK, VALUE)      (0XFD4A0200, 0x00000002U ,0x00000000U)  */
    mask_write 0XFD4A0200 0x00000002 0x00000000
		# Register : DP_TX_PHY_POWER_DOWN @ 0XFD4A0238</p>

		# Two bits per lane. When set to 11, moves the GT to power down mode. When
    #  set to 00, GT will be in active state. bits [1:0] - lane0 Bits [3:2] -
    # lane 1
		# PSU_DP_DP_TX_PHY_POWER_DOWN_POWER_DWN                                           0X0

		# Control PHY Power down
		#(OFFSET, MASK, VALUE)      (0XFD4A0238, 0x0000000FU ,0x00000000U)  */
    mask_write 0XFD4A0238 0x0000000F 0x00000000
		# : USB0 GFLADJ
		# Register : GUSB2PHYCFG @ 0XFE20C200</p>

		# USB 2.0 Turnaround Time (USBTrdTim) Sets the turnaround time in PHY cloc
    # ks. Specifies the response time for a MAC request to the Packet FIFO Con
    # troller (PFC) to fetch data from the DFIFO (SPRAM). The following are th
    # e required values for the minimum SoC bus frequency of 60 MHz. USB turna
    # round time is a critical certification criteria when using long cables a
    # nd five hub levels. The required values for this field: - 4'h5: When the
    #  MAC interface is 16-bit UTMI+. - 4'h9: When the MAC interface is 8-bit
    # UTMI+/ULPI. If SoC bus clock is less than 60 MHz, and USB turnaround tim
    # e is not critical, this field can be set to a larger value. Note: This f
    # ield is valid only in device mode.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM                                           0x9

		# Transceiver Delay: Enables a delay between the assertion of the UTMI/ULP
    # I Transceiver Select signal (for HS) and the assertion of the TxValid si
    # gnal during a HS Chirp. When this bit is set to 1, a delay (of approxima
    # tely 2.5 us) is introduced from the time when the Transceiver Select is
    # set to 2'b00 (HS) to the time the TxValid is driven to 0 for sending the
    #  chirp-K. This delay is required for some UTMI/ULPI PHYs. Note: - If you
    #  enable the hibernation feature when the device core comes out of power-
    # off, you must re-initialize this bit with the appropriate value because
    # the core does not save and restore this bit value during hibernation. -
    # This bit is valid only in device mode.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY                                             0x0

		# Enable utmi_sleep_n and utmi_l1_suspend_n (EnblSlpM) The application use
    # s this bit to control utmi_sleep_n and utmi_l1_suspend_n assertion to th
    # e PHY in the L1 state. - 1'b0: utmi_sleep_n and utmi_l1_suspend_n assert
    # ion from the core is not transferred to the external PHY. - 1'b1: utmi_s
    # leep_n and utmi_l1_suspend_n assertion from the core is transferred to t
    # he external PHY. Note: This bit must be set high for Port0 if PHY is use
    # d. Note: In Device mode - Before issuing any device endpoint command whe
    # n operating in 2.0 speeds, disable this bit and enable it after the comm
    # and completes. Without disabling this bit, if a command is issued when t
    # he device is in L1 state and if mac2_clk (utmi_clk/ulpi_clk) is gated of
    # f, the command will not get completed.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM                                            0x0

		# USB 2.0 High-Speed PHY or USB 1.1 Full-Speed Serial Transceiver Select T
    # he application uses this bit to select a high-speed PHY or a full-speed
    # transceiver. - 1'b0: USB 2.0 high-speed UTMI+ or ULPI PHY. This bit is a
    # lways 0, with Write Only access. - 1'b1: USB 1.1 full-speed serial trans
    # ceiver. This bit is always 1, with Write Only access. If both interface
    # types are selected in coreConsultant (that is, parameters' values are no
    # t zero), the application uses this bit to select the active interface is
    #  active, with Read-Write bit access. Note: USB 1.1 full-serial transceiv
    # er is not supported. This bit always reads as 1'b0.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_PHYSEL                                              0x0

		# Suspend USB2.0 HS/FS/LS PHY (SusPHY) When set, USB2.0 PHY enters Suspend
    #  mode if Suspend conditions are valid. For DRD/OTG configurations, it is
    #  recommended that this bit is set to 0 during coreConsultant configurati
    # on. If it is set to 1, then the application must clear this bit after po
    # wer-on reset. Application needs to set it to 1 after the core initializa
    # tion completes. For all other configurations, this bit can be set to 1 d
    # uring core configuration. Note: - In host mode, on reset, this bit is se
    # t to 1. Software can override this bit after reset. - In device mode, be
    # fore issuing any device endpoint command when operating in 2.0 speeds, d
    # isable this bit and enable it after the command completes. If you issue
    # a command without disabling this bit when the device is in L2 state and
    # if mac2_clk (utmi_clk/ulpi_clk) is gated off, the command will not get c
    # ompleted.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_SUSPENDUSB20                                        0x1

		# Full-Speed Serial Interface Select (FSIntf) The application uses this bi
    # t to select a unidirectional or bidirectional USB 1.1 full-speed serial
    # transceiver interface. - 1'b0: 6-pin unidirectional full-speed serial in
    # terface. This bit is set to 0 with Read Only access. - 1'b1: 3-pin bidir
    # ectional full-speed serial interface. This bit is set to 0 with Read Onl
    # y access. Note: USB 1.1 full-speed serial interface is not supported. Th
    # is bit always reads as 1'b0.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_FSINTF                                              0x0

		# ULPI or UTMI+ Select (ULPI_UTMI_Sel) The application uses this bit to se
    # lect a UTMI+ or ULPI Interface. - 1'b0: UTMI+ Interface - 1'b1: ULPI Int
    # erface This bit is writable only if UTMI+ and ULPI is specified for High
    # -Speed PHY Interface(s) in coreConsultant configuration (DWC_USB3_HSPHY_
    # INTERFACE = 3). Otherwise, this bit is read-only and the value depends o
    # n the interface selected through DWC_USB3_HSPHY_INTERFACE.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL                                       0x1

		# PHY Interface (PHYIf) If UTMI+ is selected, the application uses this bi
    # t to configure the core to support a UTMI+ PHY with an 8- or 16-bit inte
    # rface. - 1'b0: 8 bits - 1'b1: 16 bits ULPI Mode: 1'b0 Note: - All the en
    # abled 2.0 ports must have the same clock frequency as Port0 clock freque
    # ncy (utmi_clk[0]). - The UTMI 8-bit and 16-bit modes cannot be used toge
    # ther for different ports at the same time (that is, all the ports must b
    # e in 8-bit mode, or all of them must be in 16-bit mode, at a time). - If
    #  any of the USB 2.0 ports is selected as ULPI port for operation, then a
    # ll the USB 2.0 ports must be operating at 60 MHz.
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_PHYIF                                               0x0

		# HS/FS Timeout Calibration (TOutCal) The number of PHY clocks, as indicat
    # ed by the application in this field, is multiplied by a bit-time factor;
    #  this factor is added to the high-speed/full-speed interpacket timeout d
    # uration in the core to account for additional delays introduced by the P
    # HY. This may be required, since the delay introduced by the PHY in gener
    # ating the linestate condition may vary among PHYs. The USB standard time
    # out value for high-speed operation is 736 to 816 (inclusive) bit times.
    # The USB standard timeout value for full-speed operation is 16 to 18 (inc
    # lusive) bit times. The application must program this field based on the
    # speed of connection. The number of bit times added per PHY clock are: Hi
    # gh-speed operation: - One 30-MHz PHY clock = 16 bit times - One 60-MHz P
    # HY clock = 8 bit times Full-speed operation: - One 30-MHz PHY clock = 0.
    # 4 bit times - One 60-MHz PHY clock = 0.2 bit times - One 48-MHz PHY cloc
    # k = 0.25 bit times
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL                                             0x7

		# ULPI External VBUS Drive (ULPIExtVbusDrv) Selects supply source to drive
    #  5V on VBUS, in the ULPI PHY. - 1'b0: PHY drives VBUS with internal char
    # ge pump (default). - 1'b1: PHY drives VBUS with an external supply. (Onl
    # y when RTL parameter DWC_USB3_HSPHY_INTERFACE = 2 or 3)
		# PSU_USB3_0_XHCI_GUSB2PHYCFG_ULPIEXTVBUSDRV                                      0x1

		# Global USB2 PHY Configuration Register The application must program this
    #  register before starting any transactions on either the SoC bus or the
    # USB. In Device-only configurations, only one register is needed. In Host
    #  mode, per-port registers are implemented.
		#(OFFSET, MASK, VALUE)      (0XFE20C200, 0x00023FFFU ,0x00022457U)  */
    mask_write 0XFE20C200 0x00023FFF 0x00022457
		# Register : GFLADJ @ 0XFE20C630</p>

		# This field indicates the frame length adjustment to be applied when SOF/
    # ITP counter is running on the ref_clk. This register value is used to ad
    # just the ITP interval when GCTL[SOFITPSYNC] is set to '1'; SOF and ITP i
    # nterval when GLADJ.GFLADJ_REFCLK_LPM_SEL is set to '1'. This field must
    # be programmed to a non-zero value only if GFLADJ_REFCLK_LPM_SEL is set t
    # o '1' or GCTL.SOFITPSYNC is set to '1'. The value is derived as follows:
    #  FLADJ_REF_CLK_FLADJ=((125000/ref_clk_period_integer)-(125000/ref_clk_pe
    # riod)) * ref_clk_period where - the ref_clk_period_integer is the intege
    # r value of the ref_clk period got by truncating the decimal (fractional)
    #  value that is programmed in the GUCTL.REF_CLK_PERIOD field. - the ref_c
    # lk_period is the ref_clk period including the fractional value. Examples
    # : If the ref_clk is 24 MHz then - GUCTL.REF_CLK_PERIOD = 41 - GFLADJ.GLA
    # DJ_REFCLK_FLADJ = ((125000/41)-(125000/41.6666))*41.6666 = 2032 (ignorin
    # g the fractional value) If the ref_clk is 48 MHz then - GUCTL.REF_CLK_PE
    # RIOD = 20 - GFLADJ.GLADJ_REFCLK_FLADJ = ((125000/20)-(125000/20.8333))*2
    # 0.8333 = 5208 (ignoring the fractional value)
		# PSU_USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ                                      0x0

		# Global Frame Length Adjustment Register This register provides options f
    # or the software to control the core behavior with respect to SOF (Start
    # of Frame) and ITP (Isochronous Timestamp Packet) timers and frame timer
    # functionality. It provides an option to override the fladj_30mhz_reg sid
    # eband signal. In addition, it enables running SOF or ITP frame timer cou
    # nters completely from the ref_clk. This facilitates hardware LPM in host
    #  mode with the SOF or ITP counters being run from the ref_clk signal.
		#(OFFSET, MASK, VALUE)      (0XFE20C630, 0x003FFF00U ,0x00000000U)  */
    mask_write 0XFE20C630 0x003FFF00 0x00000000
		# Register : GUCTL1 @ 0XFE20C11C</p>

		# When this bit is set to '0', termsel, xcvrsel will become 0 during end o
    # f resume while the opmode will become 0 once controller completes end of
    #  resume and enters U0 state (2 separate commandswill be issued). When th
    # is bit is set to '1', all the termsel, xcvrsel, opmode becomes 0 during
    # end of resume itself (only 1 command will be issued)
		# PSU_USB3_0_XHCI_GUCTL1_RESUME_TERMSEL_XCVRSEL_UNIFY                             0x1

		# Reserved
		# PSU_USB3_0_XHCI_GUCTL1_RESERVED_9                                               0x1

		# Global User Control Register 1
		#(OFFSET, MASK, VALUE)      (0XFE20C11C, 0x00000600U ,0x00000600U)  */
    mask_write 0XFE20C11C 0x00000600 0x00000600
		# Register : GUCTL @ 0XFE20C12C</p>

		# Host IN Auto Retry (USBHstInAutoRetryEn) When set, this field enables th
    # e Auto Retry feature. For IN transfers (non-isochronous) that encounter
    # data packets with CRC errors or internal overrun scenarios, the auto ret
    # ry feature causes the Host core to reply to the device with a non-termin
    # ating retry ACK (that is, an ACK transaction packet with Retry = 1 and N
    # umP != 0). If the Auto Retry feature is disabled (default), the core wil
    # l respond with a terminating retry ACK (that is, an ACK transaction pack
    # et with Retry = 1 and NumP = 0). - 1'b0: Auto Retry Disabled - 1'b1: Aut
    # o Retry Enabled Note: This bit is also applicable to the device mode.
		# PSU_USB3_0_XHCI_GUCTL_USBHSTINAUTORETRYEN                                       0x1

		# Global User Control Register: This register provides a few options for t
    # he software to control the core behavior in the Host mode. Most of the o
    # ptions are used to improve host inter-operability with different devices
    # .
		#(OFFSET, MASK, VALUE)      (0XFE20C12C, 0x00004000U ,0x00004000U)  */
    mask_write 0XFE20C12C 0x00004000 0x00004000
		# : UPDATING TWO PCIE REGISTERS DEFAULT VALUES, AS THESE REGISTERS HAVE INCORRECT RESET VALUES IN SILICON.
		# Register : ATTR_25 @ 0XFD480064</p>

		# If TRUE Completion Timeout Disable is supported. This is required to be
    # TRUE for Endpoint and either setting allowed for Root ports. Drives Devi
    # ce Capability 2 [4]; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED                      0X1

		# ATTR_25
		#(OFFSET, MASK, VALUE)      (0XFD480064, 0x00000200U ,0x00000200U)  */
    mask_write 0XFD480064 0x00000200 0x00000200
		# : PCIE SETTINGS
		# Register : ATTR_7 @ 0XFD48001C</p>

		# Specifies mask/settings for Base Address Register (BAR) 0. If BAR is not
    #  to be implemented, set to 32'h00000000. Bits are defined as follows: Me
    # mory Space BAR [0] = Mem Space Indicator (set to 0) [2:1] = Type field (
    # 10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask
    # for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to 1, w
    # here 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:
    # n bits of \'7bBAR1,BAR0\'7d to 1. IO Space BAR 0] = IO Space Indicator (
    # set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of B
    # AR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in bytes.;
    #  EP=0x0004; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_7_ATTR_BAR0                                                0x0

		# ATTR_7
		#(OFFSET, MASK, VALUE)      (0XFD48001C, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD48001C 0x0000FFFF 0x00000000
		# Register : ATTR_8 @ 0XFD480020</p>

		# Specifies mask/settings for Base Address Register (BAR) 0. If BAR is not
    #  to be implemented, set to 32'h00000000. Bits are defined as follows: Me
    # mory Space BAR [0] = Mem Space Indicator (set to 0) [2:1] = Type field (
    # 10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask
    # for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to 1, w
    # here 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:
    # n bits of \'7bBAR1,BAR0\'7d to 1. IO Space BAR 0] = IO Space Indicator (
    # set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of B
    # AR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in bytes.;
    #  EP=0xFFF0; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_8_ATTR_BAR0                                                0x0

		# ATTR_8
		#(OFFSET, MASK, VALUE)      (0XFD480020, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480020 0x0000FFFF 0x00000000
		# Register : ATTR_9 @ 0XFD480024</p>

		# Specifies mask/settings for Base Address Register (BAR) 1 if BAR0 is a 3
    # 2-bit BAR, or the upper bits of \'7bBAR1,BAR0\'7d if BAR0 is a 64-bit BA
    # R. If BAR is not to be implemented, set to 32'h00000000. See BAR0 descri
    # ption if this functions as the upper bits of a 64-bit BAR. Bits are defi
    # ned as follows: Memory Space BAR (not upper bits of BAR0) [0] = Mem Spac
    # e Indicator (set to 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit)
    #  [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if
    # 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory aperture size
    #  in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR2,BAR1\'7d t
    # o 1. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set
    #  to 0) [31:2] = Mask for writable bits of BAR; set uppermost 31:n bits t
    # o 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_9_ATTR_BAR1                                                0x0

		# ATTR_9
		#(OFFSET, MASK, VALUE)      (0XFD480024, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480024 0x0000FFFF 0x00000000
		# Register : ATTR_10 @ 0XFD480028</p>

		# Specifies mask/settings for Base Address Register (BAR) 1 if BAR0 is a 3
    # 2-bit BAR, or the upper bits of \'7bBAR1,BAR0\'7d if BAR0 is a 64-bit BA
    # R. If BAR is not to be implemented, set to 32'h00000000. See BAR0 descri
    # ption if this functions as the upper bits of a 64-bit BAR. Bits are defi
    # ned as follows: Memory Space BAR (not upper bits of BAR0) [0] = Mem Spac
    # e Indicator (set to 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit)
    #  [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if
    # 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory aperture size
    #  in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR2,BAR1\'7d t
    # o 1. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set
    #  to 0) [31:2] = Mask for writable bits of BAR; set uppermost 31:n bits t
    # o 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_10_ATTR_BAR1                                               0x0

		# ATTR_10
		#(OFFSET, MASK, VALUE)      (0XFD480028, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480028 0x0000FFFF 0x00000000
		# Register : ATTR_11 @ 0XFD48002C</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  2 if BAR1 is a 32-bit BAR, or the upper bits of \'7bBAR2,BAR1\'7d if BA
    # R1 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR1 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root: This must be set to 00FF_FFF
    # F. For an endpoint, bits are defined as follows: Memory Space BAR (not u
    # pper bits of BAR1) [0] = Mem Space Indicator (set to 0) [2:1] = Type fie
    # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = M
    # ask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to
    # 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost
    #  63:n bits of \'7bBAR3,BAR2\'7d to 1. IO Space BAR 0] = IO Space Indicat
    # or (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits
    # of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in byt
    # es.; EP=0x0004; RP=0xFFFF
		# PSU_PCIE_ATTRIB_ATTR_11_ATTR_BAR2                                               0xFFFF

		# ATTR_11
		#(OFFSET, MASK, VALUE)      (0XFD48002C, 0x0000FFFFU ,0x0000FFFFU)  */
    mask_write 0XFD48002C 0x0000FFFF 0x0000FFFF
		# Register : ATTR_12 @ 0XFD480030</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  2 if BAR1 is a 32-bit BAR, or the upper bits of \'7bBAR2,BAR1\'7d if BA
    # R1 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR1 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root: This must be set to 00FF_FFF
    # F. For an endpoint, bits are defined as follows: Memory Space BAR (not u
    # pper bits of BAR1) [0] = Mem Space Indicator (set to 0) [2:1] = Type fie
    # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = M
    # ask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to
    # 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost
    #  63:n bits of \'7bBAR3,BAR2\'7d to 1. IO Space BAR 0] = IO Space Indicat
    # or (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits
    # of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in byt
    # es.; EP=0xFFF0; RP=0x00FF
		# PSU_PCIE_ATTRIB_ATTR_12_ATTR_BAR2                                               0xFF

		# ATTR_12
		#(OFFSET, MASK, VALUE)      (0XFD480030, 0x0000FFFFU ,0x000000FFU)  */
    mask_write 0XFD480030 0x0000FFFF 0x000000FF
		# Register : ATTR_13 @ 0XFD480034</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  3 if BAR2 is a 32-bit BAR, or the upper bits of \'7bBAR3,BAR2\'7d if BA
    # R2 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR2 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root, this must be set to: FFFF_00
    # 00 = IO Limit/Base Registers not implemented FFFF_F0F0 = IO Limit/Base R
    # egisters use 16-bit decode FFFF_F1F1 = IO Limit/Base Registers use 32-bi
    # t decode For an endpoint, bits are defined as follows: Memory Space BAR
    # (not upper bits of BAR2) [0] = Mem Space Indicator (set to 0) [2:1] = Ty
    # pe field (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:
    # 4] = Mask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bi
    # ts to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set upp
    # ermost 63:n bits of \'7bBAR4,BAR3\'7d to 1. IO Space BAR 0] = IO Space I
    # ndicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable
    #  bits of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size
    # in bytes.; EP=0xFFFF; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_13_ATTR_BAR3                                               0x0

		# ATTR_13
		#(OFFSET, MASK, VALUE)      (0XFD480034, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480034 0x0000FFFF 0x00000000
		# Register : ATTR_14 @ 0XFD480038</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  3 if BAR2 is a 32-bit BAR, or the upper bits of \'7bBAR3,BAR2\'7d if BA
    # R2 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR2 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root, this must be set to: FFFF_00
    # 00 = IO Limit/Base Registers not implemented FFFF_F0F0 = IO Limit/Base R
    # egisters use 16-bit decode FFFF_F1F1 = IO Limit/Base Registers use 32-bi
    # t decode For an endpoint, bits are defined as follows: Memory Space BAR
    # (not upper bits of BAR2) [0] = Mem Space Indicator (set to 0) [2:1] = Ty
    # pe field (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:
    # 4] = Mask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bi
    # ts to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set upp
    # ermost 63:n bits of \'7bBAR4,BAR3\'7d to 1. IO Space BAR 0] = IO Space I
    # ndicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable
    #  bits of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size
    # in bytes.; EP=0xFFFF; RP=0xFFFF
		# PSU_PCIE_ATTRIB_ATTR_14_ATTR_BAR3                                               0xFFFF

		# ATTR_14
		#(OFFSET, MASK, VALUE)      (0XFD480038, 0x0000FFFFU ,0x0000FFFFU)  */
    mask_write 0XFD480038 0x0000FFFF 0x0000FFFF
		# Register : ATTR_15 @ 0XFD48003C</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  4 if BAR3 is a 32-bit BAR, or the upper bits of \'7bBAR4,BAR3\'7d if BA
    # R3 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR3 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root: This must be set to FFF0_FFF
    # 0. For an endpoint, bits are defined as follows: Memory Space BAR (not u
    # pper bits of BAR3) [0] = Mem Space Indicator (set to 0) [2:1] = Type fie
    # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = M
    # ask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to
    # 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost
    #  63:n bits of \'7bBAR5,BAR4\'7d to 1. IO Space BAR 0] = IO Space Indicat
    # or (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits
    # of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in byt
    # es.; EP=0x0004; RP=0xFFF0
		# PSU_PCIE_ATTRIB_ATTR_15_ATTR_BAR4                                               0xFFF0

		# ATTR_15
		#(OFFSET, MASK, VALUE)      (0XFD48003C, 0x0000FFFFU ,0x0000FFF0U)  */
    mask_write 0XFD48003C 0x0000FFFF 0x0000FFF0
		# Register : ATTR_16 @ 0XFD480040</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  4 if BAR3 is a 32-bit BAR, or the upper bits of \'7bBAR4,BAR3\'7d if BA
    # R3 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR3 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root: This must be set to FFF0_FFF
    # 0. For an endpoint, bits are defined as follows: Memory Space BAR (not u
    # pper bits of BAR3) [0] = Mem Space Indicator (set to 0) [2:1] = Type fie
    # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = M
    # ask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to
    # 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost
    #  63:n bits of \'7bBAR5,BAR4\'7d to 1. IO Space BAR 0] = IO Space Indicat
    # or (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits
    # of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in byt
    # es.; EP=0xFFF0; RP=0xFFF0
		# PSU_PCIE_ATTRIB_ATTR_16_ATTR_BAR4                                               0xFFF0

		# ATTR_16
		#(OFFSET, MASK, VALUE)      (0XFD480040, 0x0000FFFFU ,0x0000FFF0U)  */
    mask_write 0XFD480040 0x0000FFFF 0x0000FFF0
		# Register : ATTR_17 @ 0XFD480044</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  5 if BAR4 is a 32-bit BAR, or the upper bits of \'7bBAR5,BAR4\'7d if BA
    # R4 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR4 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root, this must be set to: 0000_00
    # 00 = Prefetchable Memory Limit/Base Registers not implemented FFF0_FFF0
    # = 32-bit Prefetchable Memory Limit/Base implemented FFF1_FFF1 = 64-bit P
    # refetchable Memory Limit/Base implemented For an endpoint, bits are defi
    # ned as follows: Memory Space BAR (not upper bits of BAR4) [0] = Mem Spac
    # e Indicator (set to 0) [2:1] = Type field (00 for 32-bit; BAR5 cannot be
    #  lower part of a 64-bit BAR) [3] = Prefetchable (0 or 1) [31:4] = Mask f
    # or writable bits of BAR; set uppermost 31:n bits to 1, where 2^n=memory
    # aperture size in bytes. IO Space BAR 0] = IO Space Indicator (set to 1)
    # [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set up
    # permost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF
    # ; RP=0xFFF1
		# PSU_PCIE_ATTRIB_ATTR_17_ATTR_BAR5                                               0xFFF1

		# ATTR_17
		#(OFFSET, MASK, VALUE)      (0XFD480044, 0x0000FFFFU ,0x0000FFF1U)  */
    mask_write 0XFD480044 0x0000FFFF 0x0000FFF1
		# Register : ATTR_18 @ 0XFD480048</p>

		# For an endpoint, specifies mask/settings for Base Address Register (BAR)
    #  5 if BAR4 is a 32-bit BAR, or the upper bits of \'7bBAR5,BAR4\'7d if BA
    # R4 is the lower part of a 64-bit BAR. If BAR is not to be implemented, s
    # et to 32'h00000000. See BAR4 description if this functions as the upper
    # bits of a 64-bit BAR. For a switch or root, this must be set to: 0000_00
    # 00 = Prefetchable Memory Limit/Base Registers not implemented FFF0_FFF0
    # = 32-bit Prefetchable Memory Limit/Base implemented FFF1_FFF1 = 64-bit P
    # refetchable Memory Limit/Base implemented For an endpoint, bits are defi
    # ned as follows: Memory Space BAR (not upper bits of BAR4) [0] = Mem Spac
    # e Indicator (set to 0) [2:1] = Type field (00 for 32-bit; BAR5 cannot be
    #  lower part of a 64-bit BAR) [3] = Prefetchable (0 or 1) [31:4] = Mask f
    # or writable bits of BAR; set uppermost 31:n bits to 1, where 2^n=memory
    # aperture size in bytes. IO Space BAR 0] = IO Space Indicator (set to 1)
    # [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set up
    # permost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF
    # ; RP=0xFFF1
		# PSU_PCIE_ATTRIB_ATTR_18_ATTR_BAR5                                               0xFFF1

		# ATTR_18
		#(OFFSET, MASK, VALUE)      (0XFD480048, 0x0000FFFFU ,0x0000FFF1U)  */
    mask_write 0XFD480048 0x0000FFFF 0x0000FFF1
		# Register : ATTR_27 @ 0XFD48006C</p>

		# Specifies maximum payload supported. Valid settings are: 0- 128 bytes, 1
    # - 256 bytes, 2- 512 bytes, 3- 1024 bytes. Transferred to the Device Capa
    # bilities register. The values: 4-2048 bytes, 5- 4096 bytes are not suppo
    # rted; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_27_ATTR_DEV_CAP_MAX_PAYLOAD_SUPPORTED                      1

		# Endpoint L1 Acceptable Latency. Records the latency that the endpoint ca
    # n withstand on transitions from L1 state to L0 (if L1 state supported).
    # Valid settings are: 0h less than 1us, 1h 1 to 2us, 2h 2 to 4us, 3h 4 to
    # 8us, 4h 8 to 16us, 5h 16 to 32us, 6h 32 to 64us, 7h more than 64us. For
    # Endpoints only. Must be 0h for other devices.; EP=0x0007; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_27_ATTR_DEV_CAP_ENDPOINT_L1_LATENCY                        0x0

		# ATTR_27
		#(OFFSET, MASK, VALUE)      (0XFD48006C, 0x00000738U ,0x00000100U)  */
    mask_write 0XFD48006C 0x00000738 0x00000100
		# Register : ATTR_50 @ 0XFD4800C8</p>

		# Identifies the type of device/port as follows: 0000b PCI Express Endpoin
    # t device, 0001b Legacy PCI Express Endpoint device, 0100b Root Port of P
    # CI Express Root Complex, 0101b Upstream Port of PCI Express Switch, 0110
    # b Downstream Port of PCI Express Switch, 0111b PCIE Express to PCI/PCI-X
    #  Bridge, 1000b PCI/PCI-X to PCI Express Bridge. Transferred to PCI Expre
    # ss Capabilities register. Must be consistent with IS_SWITCH and UPSTREAM
    # _FACING settings.; EP=0x0000; RP=0x0004
		# PSU_PCIE_ATTRIB_ATTR_50_ATTR_PCIE_CAP_DEVICE_PORT_TYPE                          4

		# PCIe Capability's Next Capability Offset pointer to the next item in the
    #  capabilities list, or 00h if this is the final capability.; EP=0x009C;
    # RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_50_ATTR_PCIE_CAP_NEXTPTR                                   0

		# ATTR_50
		#(OFFSET, MASK, VALUE)      (0XFD4800C8, 0x0000FFF0U ,0x00000040U)  */
    mask_write 0XFD4800C8 0x0000FFF0 0x00000040
		# Register : ATTR_105 @ 0XFD4801A4</p>

		# Number of credits that should be advertised for Completion data received
    #  on Virtual Channel 0. The bytes advertised must be less than or equal t
    # o the bram bytes available. See VC0_RX_RAM_LIMIT; EP=0x0172; RP=0x00CD
		# PSU_PCIE_ATTRIB_ATTR_105_ATTR_VC0_TOTAL_CREDITS_CD                              0xCD

		# ATTR_105
		#(OFFSET, MASK, VALUE)      (0XFD4801A4, 0x000007FFU ,0x000000CDU)  */
    mask_write 0XFD4801A4 0x000007FF 0x000000CD
		# Register : ATTR_106 @ 0XFD4801A8</p>

		# Number of credits that should be advertised for Completion headers recei
    # ved on Virtual Channel 0. The sum of the posted, non posted, and complet
    # ion header credits must be <= 80; EP=0x0048; RP=0x0024
		# PSU_PCIE_ATTRIB_ATTR_106_ATTR_VC0_TOTAL_CREDITS_CH                              0x24

		# Number of credits that should be advertised for Non-Posted headers recei
    # ved on Virtual Channel 0. The number of non posted data credits advertis
    # ed by the block is equal to the number of non posted header credits. The
    #  sum of the posted, non posted, and completion header credits must be <=
    #  80; EP=0x0004; RP=0x000C
		# PSU_PCIE_ATTRIB_ATTR_106_ATTR_VC0_TOTAL_CREDITS_NPH                             0xC

		# ATTR_106
		#(OFFSET, MASK, VALUE)      (0XFD4801A8, 0x00003FFFU ,0x00000624U)  */
    mask_write 0XFD4801A8 0x00003FFF 0x00000624
		# Register : ATTR_107 @ 0XFD4801AC</p>

		# Number of credits that should be advertised for Non-Posted data received
    #  on Virtual Channel 0. The number of non posted data credits advertised
    # by the block is equal to two times the number of non posted header credi
    # ts if atomic operations are supported or is equal to the number of non p
    # osted header credits if atomic operations are not supported. The bytes a
    # dvertised must be less than or equal to the bram bytes available. See VC
    # 0_RX_RAM_LIMIT; EP=0x0008; RP=0x0018
		# PSU_PCIE_ATTRIB_ATTR_107_ATTR_VC0_TOTAL_CREDITS_NPD                             0x18

		# ATTR_107
		#(OFFSET, MASK, VALUE)      (0XFD4801AC, 0x000007FFU ,0x00000018U)  */
    mask_write 0XFD4801AC 0x000007FF 0x00000018
		# Register : ATTR_108 @ 0XFD4801B0</p>

		# Number of credits that should be advertised for Posted data received on
    # Virtual Channel 0. The bytes advertised must be less than or equal to th
    # e bram bytes available. See VC0_RX_RAM_LIMIT; EP=0x0020; RP=0x00B5
		# PSU_PCIE_ATTRIB_ATTR_108_ATTR_VC0_TOTAL_CREDITS_PD                              0xB5

		# ATTR_108
		#(OFFSET, MASK, VALUE)      (0XFD4801B0, 0x000007FFU ,0x000000B5U)  */
    mask_write 0XFD4801B0 0x000007FF 0x000000B5
		# Register : ATTR_109 @ 0XFD4801B4</p>

		# Not currently in use. Invert ECRC generated by block when trn_tecrc_gen_
    # n and trn_terrfwd_n are asserted.; EP=0x0000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_109_ATTR_TECRC_EP_INV                                      0x0

		# Enables td bit clear and ECRC trim on received TLP's FALSE == don't trim
    #  TRUE == trim.; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_109_ATTR_RECRC_CHK_TRIM                                    0x1

		# Enables ECRC check on received TLP's 0 == don't check 1 == always check
    # 3 == check if enabled by ECRC check enable bit of AER cap structure; EP=
    # 0x0003; RP=0x0003
		# PSU_PCIE_ATTRIB_ATTR_109_ATTR_RECRC_CHK                                         0x3

		# Index of last packet buffer used by TX TLM (i.e. number of buffers - 1).
    #  Calculated from max payload size supported and the number of brams conf
    # igured for transmit; EP=0x001C; RP=0x001C
		# PSU_PCIE_ATTRIB_ATTR_109_ATTR_VC0_TX_LASTPACKET                                 0x1c

		# Number of credits that should be advertised for Posted headers received
    # on Virtual Channel 0. The sum of the posted, non posted, and completion
    # header credits must be <= 80; EP=0x0004; RP=0x0020
		# PSU_PCIE_ATTRIB_ATTR_109_ATTR_VC0_TOTAL_CREDITS_PH                              0x20

		# ATTR_109
		#(OFFSET, MASK, VALUE)      (0XFD4801B4, 0x0000FFFFU ,0x00007E20U)  */
    mask_write 0XFD4801B4 0x0000FFFF 0x00007E20
		# Register : ATTR_34 @ 0XFD480088</p>

		# Specifies values to be transferred to Header Type register. Bit 7 should
    #  be set to '0' indicating single-function device. Bit 0 identifies heade
    # r as Type 0 or Type 1, with '0' indicating a Type 0 header.; EP=0x0000;
    # RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_34_ATTR_HEADER_TYPE                                        0x1

		# ATTR_34
		#(OFFSET, MASK, VALUE)      (0XFD480088, 0x000000FFU ,0x00000001U)  */
    mask_write 0XFD480088 0x000000FF 0x00000001
		# Register : ATTR_53 @ 0XFD4800D4</p>

		# PM Capability's Next Capability Offset pointer to the next item in the c
    # apabilities list, or 00h if this is the final capability.; EP=0x0048; RP
    # =0x0060
		# PSU_PCIE_ATTRIB_ATTR_53_ATTR_PM_CAP_NEXTPTR                                     0x60

		# ATTR_53
		#(OFFSET, MASK, VALUE)      (0XFD4800D4, 0x000000FFU ,0x00000060U)  */
    mask_write 0XFD4800D4 0x000000FF 0x00000060
		# Register : ATTR_41 @ 0XFD4800A4</p>

		# MSI Per-Vector Masking Capable. The value is transferred to the MSI Cont
    # rol Register[8]. When set, adds Mask and Pending Dword to Cap structure;
    #  EP=0x0000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_PER_VECTOR_MASKING_CAPABLE                 0x0

		# Indicates that the MSI structures exists. If this is FALSE, then the MSI
    #  structure cannot be accessed via either the link or the management port
    # .; EP=0x0001; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_ON                                         0

		# MSI Capability's Next Capability Offset pointer to the next item in the
    # capabilities list, or 00h if this is the final capability.; EP=0x0060; R
    # P=0x0000
		# PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_NEXTPTR                                    0x0

		# Indicates that the MSI structures exists. If this is FALSE, then the MSI
    #  structure cannot be accessed via either the link or the management port
    # .; EP=0x0001; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_ON                                         0

		# ATTR_41
		#(OFFSET, MASK, VALUE)      (0XFD4800A4, 0x000003FFU ,0x00000000U)  */
    mask_write 0XFD4800A4 0x000003FF 0x00000000
		# Register : ATTR_97 @ 0XFD480184</p>

		# Maximum Link Width. Valid settings are: 000001b x1, 000010b x2, 000100b
    # x4, 001000b x8.; EP=0x0004; RP=0x0004
		# PSU_PCIE_ATTRIB_ATTR_97_ATTR_LINK_CAP_MAX_LINK_WIDTH                            0x1

		# Used by LTSSM to set Maximum Link Width. Valid settings are: 000001b [x1
    # ], 000010b [x2], 000100b [x4], 001000b [x8].; EP=0x0004; RP=0x0004
		# PSU_PCIE_ATTRIB_ATTR_97_ATTR_LTSSM_MAX_LINK_WIDTH                               0x1

		# ATTR_97
		#(OFFSET, MASK, VALUE)      (0XFD480184, 0x00000FFFU ,0x00000041U)  */
    mask_write 0XFD480184 0x00000FFF 0x00000041
		# Register : ATTR_100 @ 0XFD480190</p>

		# TRUE specifies upstream-facing port. FALSE specifies downstream-facing p
    # ort.; EP=0x0001; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_100_ATTR_UPSTREAM_FACING                                   0x0

		# ATTR_100
		#(OFFSET, MASK, VALUE)      (0XFD480190, 0x00000040U ,0x00000000U)  */
    mask_write 0XFD480190 0x00000040 0x00000000
		# Register : ATTR_101 @ 0XFD480194</p>

		# Enable the routing of message TLPs to the user through the TRN RX interf
    # ace. A bit value of 1 enables routing of the message TLP to the user. Me
    # ssages are always decoded by the message decoder. Bit 0 - ERR COR, Bit 1
    #  - ERR NONFATAL, Bit 2 - ERR FATAL, Bit 3 - INTA Bit 4 - INTB, Bit 5 - I
    # NTC, Bit 6 - INTD, Bit 7 PM_PME, Bit 8 - PME_TO_ACK, Bit 9 - unlock, Bit
    #  10 PME_Turn_Off; EP=0x0000; RP=0x07FF
		# PSU_PCIE_ATTRIB_ATTR_101_ATTR_ENABLE_MSG_ROUTE                                  0x7FF

		# Disable BAR filtering. Does not change the behavior of the bar hit outpu
    # ts; EP=0x0000; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_101_ATTR_DISABLE_BAR_FILTERING                             0x1

		# ATTR_101
		#(OFFSET, MASK, VALUE)      (0XFD480194, 0x0000FFE2U ,0x0000FFE2U)  */
    mask_write 0XFD480194 0x0000FFE2 0x0000FFE2
		# Register : ATTR_37 @ 0XFD480094</p>

		# Link Bandwidth notification capability. Indicates support for the link b
    # andwidth notification status and interrupt mechanism. Required for Root.
    # ; EP=0x0000; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_37_ATTR_LINK_CAP_LINK_BANDWIDTH_NOTIFICATION_CAP           0x1

		# Sets the ASPM Optionality Compliance bit, to comply with the 2.1 ASPM Op
    # tionality ECN. Transferred to the Link Capabilities register.; EP=0x0001
    # ; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_37_ATTR_LINK_CAP_ASPM_OPTIONALITY                          0x1

		# ATTR_37
		#(OFFSET, MASK, VALUE)      (0XFD480094, 0x00004200U ,0x00004200U)  */
    mask_write 0XFD480094 0x00004200 0x00004200
		# Register : ATTR_93 @ 0XFD480174</p>

		# Enables the Replay Timer to use the user-defined LL_REPLAY_TIMEOUT value
    #  (or combined with the built-in value, depending on LL_REPLAY_TIMEOUT_FU
    # NC). If FALSE, the built-in value is used.; EP=0x0000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_93_ATTR_LL_REPLAY_TIMEOUT_EN                               0x1

		# Sets a user-defined timeout for the Replay Timer to force cause the retr
    # ansmission of unacknowledged TLPs; refer to LL_REPLAY_TIMEOUT_EN and LL_
    # REPLAY_TIMEOUT_FUNC to see how this value is used. The unit for this att
    # ribute is in symbol times, which is 4ns at GEN1 speeds and 2ns at GEN2.;
    #  EP=0x0000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_93_ATTR_LL_REPLAY_TIMEOUT                                  0x1000

		# ATTR_93
		#(OFFSET, MASK, VALUE)      (0XFD480174, 0x0000FFFFU ,0x00009000U)  */
    mask_write 0XFD480174 0x0000FFFF 0x00009000
		# Register : ID @ 0XFD480200</p>

		# Device ID for the the PCIe Cap Structure Device ID field
		# PSU_PCIE_ATTRIB_ID_CFG_DEV_ID                                                   0xd021

		# Vendor ID for the PCIe Cap Structure Vendor ID field
		# PSU_PCIE_ATTRIB_ID_CFG_VEND_ID                                                  0x10ee

		# ID
		#(OFFSET, MASK, VALUE)      (0XFD480200, 0xFFFFFFFFU ,0x10EED021U)  */
    mask_write 0XFD480200 0xFFFFFFFF 0x10EED021
		# Register : SUBSYS_ID @ 0XFD480204</p>

		# Subsystem ID for the the PCIe Cap Structure Subsystem ID field
		# PSU_PCIE_ATTRIB_SUBSYS_ID_CFG_SUBSYS_ID                                         0x7

		# Subsystem Vendor ID for the PCIe Cap Structure Subsystem Vendor ID field
		# PSU_PCIE_ATTRIB_SUBSYS_ID_CFG_SUBSYS_VEND_ID                                    0x10ee

		# SUBSYS_ID
		#(OFFSET, MASK, VALUE)      (0XFD480204, 0xFFFFFFFFU ,0x10EE0007U)  */
    mask_write 0XFD480204 0xFFFFFFFF 0x10EE0007
		# Register : REV_ID @ 0XFD480208</p>

		# Revision ID for the the PCIe Cap Structure
		# PSU_PCIE_ATTRIB_REV_ID_CFG_REV_ID                                               0x0

		# REV_ID
		#(OFFSET, MASK, VALUE)      (0XFD480208, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD480208 0x000000FF 0x00000000
		# Register : ATTR_24 @ 0XFD480060</p>

		# Code identifying basic function, subclass and applicable programming int
    # erface. Transferred to the Class Code register.; EP=0x8000; RP=0x8000
		# PSU_PCIE_ATTRIB_ATTR_24_ATTR_CLASS_CODE                                         0x400

		# ATTR_24
		#(OFFSET, MASK, VALUE)      (0XFD480060, 0x0000FFFFU ,0x00000400U)  */
    mask_write 0XFD480060 0x0000FFFF 0x00000400
		# Register : ATTR_25 @ 0XFD480064</p>

		# Code identifying basic function, subclass and applicable programming int
    # erface. Transferred to the Class Code register.; EP=0x0005; RP=0x0006
		# PSU_PCIE_ATTRIB_ATTR_25_ATTR_CLASS_CODE                                         0x6

		# INTX Interrupt Generation Capable. If FALSE, this will cause Command[10]
    #  to be hardwired to 0.; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_25_ATTR_CMD_INTX_IMPLEMENTED                               0

		# ATTR_25
		#(OFFSET, MASK, VALUE)      (0XFD480064, 0x000001FFU ,0x00000006U)  */
    mask_write 0XFD480064 0x000001FF 0x00000006
		# Register : ATTR_4 @ 0XFD480010</p>

		# Indicates that the AER structures exists. If this is FALSE, then the AER
    #  structure cannot be accessed via either the link or the management port
    # , and AER will be considered to not be present for error management task
    # s (such as what types of error messages are sent if an error is detected
    # ).; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_4_ATTR_AER_CAP_ON                                          0

		# Indicates that the AER structures exists. If this is FALSE, then the AER
    #  structure cannot be accessed via either the link or the management port
    # , and AER will be considered to not be present for error management task
    # s (such as what types of error messages are sent if an error is detected
    # ).; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_4_ATTR_AER_CAP_ON                                          0

		# ATTR_4
		#(OFFSET, MASK, VALUE)      (0XFD480010, 0x00001000U ,0x00000000U)  */
    mask_write 0XFD480010 0x00001000 0x00000000
		# Register : ATTR_89 @ 0XFD480164</p>

		# VSEC's Next Capability Offset pointer to the next item in the capabiliti
    # es list, or 000h if this is the final capability.; EP=0x0140; RP=0x0140
		# PSU_PCIE_ATTRIB_ATTR_89_ATTR_VSEC_CAP_NEXTPTR                                   0

		# ATTR_89
		#(OFFSET, MASK, VALUE)      (0XFD480164, 0x00001FFEU ,0x00000000U)  */
    mask_write 0XFD480164 0x00001FFE 0x00000000
		# Register : ATTR_79 @ 0XFD48013C</p>

		# CRS SW Visibility. Indicates RC can return CRS to SW. Transferred to the
    #  Root Capabilities register.; EP=0x0000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_79_ATTR_ROOT_CAP_CRS_SW_VISIBILITY                         1

		# ATTR_79
		#(OFFSET, MASK, VALUE)      (0XFD48013C, 0x00000020U ,0x00000020U)  */
    mask_write 0XFD48013C 0x00000020 0x00000020
		# Register : ATTR_43 @ 0XFD4800AC</p>

		# Indicates that the MSIX structures exists. If this is FALSE, then the MS
    # IX structure cannot be accessed via either the link or the management po
    # rt.; EP=0x0001; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_43_ATTR_MSIX_CAP_ON                                        0

		# ATTR_43
		#(OFFSET, MASK, VALUE)      (0XFD4800AC, 0x00000100U ,0x00000000U)  */
    mask_write 0XFD4800AC 0x00000100 0x00000000
		# Register : ATTR_48 @ 0XFD4800C0</p>

		# MSI-X Table Size. This value is transferred to the MSI-X Message Control
    # [10:0] field. Set to 0 if MSI-X is not enabled. Note that the core does
    # not implement the table; that must be implemented in user logic.; EP=0x0
    # 003; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_48_ATTR_MSIX_CAP_TABLE_SIZE                                0

		# ATTR_48
		#(OFFSET, MASK, VALUE)      (0XFD4800C0, 0x000007FFU ,0x00000000U)  */
    mask_write 0XFD4800C0 0x000007FF 0x00000000
		# Register : ATTR_46 @ 0XFD4800B8</p>

		# MSI-X Table Offset. This value is transferred to the MSI-X Table Offset
    # field. Set to 0 if MSI-X is not enabled.; EP=0x0001; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_46_ATTR_MSIX_CAP_TABLE_OFFSET                              0

		# ATTR_46
		#(OFFSET, MASK, VALUE)      (0XFD4800B8, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD4800B8 0x0000FFFF 0x00000000
		# Register : ATTR_47 @ 0XFD4800BC</p>

		# MSI-X Table Offset. This value is transferred to the MSI-X Table Offset
    # field. Set to 0 if MSI-X is not enabled.; EP=0x0000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_47_ATTR_MSIX_CAP_TABLE_OFFSET                              0

		# ATTR_47
		#(OFFSET, MASK, VALUE)      (0XFD4800BC, 0x00001FFFU ,0x00000000U)  */
    mask_write 0XFD4800BC 0x00001FFF 0x00000000
		# Register : ATTR_44 @ 0XFD4800B0</p>

		# MSI-X Pending Bit Array Offset This value is transferred to the MSI-X PB
    # A Offset field. Set to 0 if MSI-X is not enabled.; EP=0x0001; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_44_ATTR_MSIX_CAP_PBA_OFFSET                                0

		# ATTR_44
		#(OFFSET, MASK, VALUE)      (0XFD4800B0, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD4800B0 0x0000FFFF 0x00000000
		# Register : ATTR_45 @ 0XFD4800B4</p>

		# MSI-X Pending Bit Array Offset This value is transferred to the MSI-X PB
    # A Offset field. Set to 0 if MSI-X is not enabled.; EP=0x1000; RP=0x0000
		# PSU_PCIE_ATTRIB_ATTR_45_ATTR_MSIX_CAP_PBA_OFFSET                                0

		# ATTR_45
		#(OFFSET, MASK, VALUE)      (0XFD4800B4, 0x0000FFF8U ,0x00000000U)  */
    mask_write 0XFD4800B4 0x0000FFF8 0x00000000
		# Register : CB @ 0XFD48031C</p>

		# DT837748 Enable
		# PSU_PCIE_ATTRIB_CB_CB1                                                          0x0

		# ECO Register 1
		#(OFFSET, MASK, VALUE)      (0XFD48031C, 0x00000002U ,0x00000000U)  */
    mask_write 0XFD48031C 0x00000002 0x00000000
		# Register : ATTR_35 @ 0XFD48008C</p>

		# Active State PM Support. Indicates the level of active state power manag
    # ement supported by the selected PCI Express Link, encoded as follows: 0
    # Reserved, 1 L0s entry supported, 2 Reserved, 3 L0s and L1 entry supporte
    # d.; EP=0x0001; RP=0x0001
		# PSU_PCIE_ATTRIB_ATTR_35_ATTR_LINK_CAP_ASPM_SUPPORT                              0x0

		# ATTR_35
		#(OFFSET, MASK, VALUE)      (0XFD48008C, 0x00003000U ,0x00000000U)  */
    mask_write 0XFD48008C 0x00003000 0x00000000
		# : PUTTING PCIE CONTROL IN RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# PCIE control block level reset
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_CTRL_RESET                                         0X0

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00020000U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x00020000 0x00000000
		# : PCIE GPIO RESET
		# : MASK_DATA_0_LSW LOW BANK [15:0]
		# : MASK_DATA_0_MSW LOW BANK [25:16]
		# : MASK_DATA_1_LSW LOW BANK [41:26]
		# Register : MASK_DATA_1_LSW @ 0XFF0A0008</p>

		# Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW]
		# PSU_GPIO_MASK_DATA_1_LSW_MASK_1_LSW                                             0xffdf

		# Operation is the same as MASK_DATA_0_LSW[DATA_0_LSW]
		# PSU_GPIO_MASK_DATA_1_LSW_DATA_1_LSW                                             0x20

		# Maskable Output Data (GPIO Bank1, MIO, Lower 16bits)
		#(OFFSET, MASK, VALUE)      (0XFF0A0008, 0xFFFFFFFFU ,0xFFDF0020U)  */
    mask_write 0XFF0A0008 0xFFFFFFFF 0xFFDF0020
		# : MASK_DATA_1_MSW HIGH BANK [51:42]
		# : MASK_DATA_1_LSW HIGH BANK [67:52]
		# : MASK_DATA_1_LSW HIGH BANK [77:68]
		# : CHECK PLL LOCK FOR LANE0
		# Register : L0_PLL_STATUS_READ_1 @ 0XFD4023E4</p>

		# Status Read value of PLL Lock
		# PSU_SERDES_L0_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD4023E4 0x00000010
		# : CHECK PLL LOCK FOR LANE1
		# Register : L1_PLL_STATUS_READ_1 @ 0XFD4063E4</p>

		# Status Read value of PLL Lock
		# PSU_SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD4063E4 0x00000010
		# : CHECK PLL LOCK FOR LANE2
		# Register : L2_PLL_STATUS_READ_1 @ 0XFD40A3E4</p>

		# Status Read value of PLL Lock
		# PSU_SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD40A3E4 0x00000010
		# : CHECK PLL LOCK FOR LANE3
		# Register : L3_PLL_STATUS_READ_1 @ 0XFD40E3E4</p>

		# Status Read value of PLL Lock
		# PSU_SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD40E3E4 0x00000010
		# : SATA AHCI VENDOR SETTING
		# Register : PP2C @ 0XFD0C00AC</p>

		# CIBGMN: COMINIT Burst Gap Minimum.
		# PSU_SATA_AHCI_VENDOR_PP2C_CIBGMN                                                0x18

		# CIBGMX: COMINIT Burst Gap Maximum.
		# PSU_SATA_AHCI_VENDOR_PP2C_CIBGMX                                                0x40

		# CIBGN: COMINIT Burst Gap Nominal.
		# PSU_SATA_AHCI_VENDOR_PP2C_CIBGN                                                 0x18

		# CINMP: COMINIT Negate Minimum Period.
		# PSU_SATA_AHCI_VENDOR_PP2C_CINMP                                                 0x28

		# PP2C - Port Phy2Cfg Register. This register controls the configuration o
    # f the Phy Control OOB timing for the COMINIT parameters for either Port
    # 0 or Port 1. The Port configured is controlled by the value programmed i
    # nto the Port Config Register.
		#(OFFSET, MASK, VALUE)      (0XFD0C00AC, 0xFFFFFFFFU ,0x28184018U)  */
    mask_write 0XFD0C00AC 0xFFFFFFFF 0x28184018
		# Register : PP3C @ 0XFD0C00B0</p>

		# CWBGMN: COMWAKE Burst Gap Minimum.
		# PSU_SATA_AHCI_VENDOR_PP3C_CWBGMN                                                0x06

		# CWBGMX: COMWAKE Burst Gap Maximum.
		# PSU_SATA_AHCI_VENDOR_PP3C_CWBGMX                                                0x14

		# CWBGN: COMWAKE Burst Gap Nominal.
		# PSU_SATA_AHCI_VENDOR_PP3C_CWBGN                                                 0x08

		# CWNMP: COMWAKE Negate Minimum Period.
		# PSU_SATA_AHCI_VENDOR_PP3C_CWNMP                                                 0x0E

		# PP3C - Port Phy3CfgRegister. This register controls the configuration of
    #  the Phy Control OOB timing for the COMWAKE parameters for either Port 0
    #  or Port 1. The Port configured is controlled by the value programmed in
    # to the Port Config Register.
		#(OFFSET, MASK, VALUE)      (0XFD0C00B0, 0xFFFFFFFFU ,0x0E081406U)  */
    mask_write 0XFD0C00B0 0xFFFFFFFF 0x0E081406
		# Register : PP4C @ 0XFD0C00B4</p>

		# BMX: COM Burst Maximum.
		# PSU_SATA_AHCI_VENDOR_PP4C_BMX                                                   0x13

		# BNM: COM Burst Nominal.
		# PSU_SATA_AHCI_VENDOR_PP4C_BNM                                                   0x08

		# SFD: Signal Failure Detection, if the signal detection de-asserts for a
    # time greater than this then the OOB detector will determine this is a li
    # ne idle and cause the PhyInit state machine to exit the Phy Ready State.
    #  A value of zero disables the Signal Failure Detector. The value is base
    # d on the OOB Detector Clock typically (PMCLK Clock Period) * SFD giving
    # a nominal time of 500ns based on a 150MHz PMCLK.
		# PSU_SATA_AHCI_VENDOR_PP4C_SFD                                                   0x4A

		# PTST: Partial to Slumber timer value, specific delay the controller shou
    # ld apply while in partial before entering slumber. The value is bases on
    #  the system clock divided by 128, total delay = (Sys Clock Period) * PTS
    # T * 128
		# PSU_SATA_AHCI_VENDOR_PP4C_PTST                                                  0x06

		# PP4C - Port Phy4Cfg Register. This register controls the configuration o
    # f the Phy Control Burst timing for the COM parameters for either Port 0
    # or Port 1. The Port configured is controlled by the value programmed int
    # o the Port Config Register.
		#(OFFSET, MASK, VALUE)      (0XFD0C00B4, 0xFFFFFFFFU ,0x064A0813U)  */
    mask_write 0XFD0C00B4 0xFFFFFFFF 0x064A0813
		# Register : PP5C @ 0XFD0C00B8</p>

		# RIT: Retry Interval Timer. The calculated value divided by two, the lowe
    # r digit of precision is not needed.
		# PSU_SATA_AHCI_VENDOR_PP5C_RIT                                                   0xC96A4

		# RCT: Rate Change Timer, a value based on the 54.2us for which a SATA dev
    # ice will transmit at a fixed rate ALIGNp after OOB has completed, for a
    # fast SERDES it is suggested that this value be 54.2us / 4
		# PSU_SATA_AHCI_VENDOR_PP5C_RCT                                                   0x3FF

		# PP5C - Port Phy5Cfg Register. This register controls the configuration o
    # f the Phy Control Retry Interval timing for either Port 0 or Port 1. The
    #  Port configured is controlled by the value programmed into the Port Con
    # fig Register.
		#(OFFSET, MASK, VALUE)      (0XFD0C00B8, 0xFFFFFFFFU ,0x3FFC96A4U)  */
    mask_write 0XFD0C00B8 0xFFFFFFFF 0x3FFC96A4
}

set psu_resetin_init_data {
		# : PUTTING SERDES PERIPHERAL IN RESET
		# : PUTTING USB0 IN RESET
		# Register : RST_LPD_TOP @ 0XFF5E023C</p>

		# USB 0 reset for control registers
		# PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET                                          0X1

		# USB 0 sleep circuit reset
		# PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET                                         0X1

		# USB 0 reset
		# PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET                                          0X1

		# Software control register for the LPD block.
		#(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000540U ,0x00000540U)  */
    mask_write 0XFF5E023C 0x00000540 0x00000540
		# : PUTTING GEM0 IN RESET
		# Register : RST_LPD_IOU0 @ 0XFF5E0230</p>

		# GEM 3 reset
		# PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET                                             0X1

		# Software controlled reset for the GEMs
		#(OFFSET, MASK, VALUE)      (0XFF5E0230, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF5E0230 0x00000008 0x00000008
		# : PUTTING SATA IN RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# Sata block level reset
		# PSU_CRF_APB_RST_FPD_TOP_SATA_RESET                                              0X1

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00000002U ,0x00000002U)  */
    mask_write 0XFD1A0100 0x00000002 0x00000002
		# : PUTTING PCIE IN RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# PCIE config reset
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_CFG_RESET                                          0X1

		# PCIE control block level reset
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_CTRL_RESET                                         0X1

		# PCIE bridge block level reset (AXI interface)
		# PSU_CRF_APB_RST_FPD_TOP_PCIE_BRIDGE_RESET                                       0X1

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x000E0000U ,0x000E0000U)  */
    mask_write 0XFD1A0100 0x000E0000 0x000E0000
		# : PUTTING DP IN RESET
		# Register : DP_TX_PHY_POWER_DOWN @ 0XFD4A0238</p>

		# Two bits per lane. When set to 11, moves the GT to power down mode. When
    #  set to 00, GT will be in active state. bits [1:0] - lane0 Bits [3:2] -
    # lane 1
		# PSU_DP_DP_TX_PHY_POWER_DOWN_POWER_DWN                                           0XA

		# Control PHY Power down
		#(OFFSET, MASK, VALUE)      (0XFD4A0238, 0x0000000FU ,0x0000000AU)  */
    mask_write 0XFD4A0238 0x0000000F 0x0000000A
		# Register : DP_PHY_RESET @ 0XFD4A0200</p>

		# Set to '1' to hold the GT in reset. Clear to release.
		# PSU_DP_DP_PHY_RESET_GT_RESET                                                    0X1

		# Reset the transmitter PHY.
		#(OFFSET, MASK, VALUE)      (0XFD4A0200, 0x00000002U ,0x00000002U)  */
    mask_write 0XFD4A0200 0x00000002 0x00000002
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# Display Port block level reset (includes DPDMA)
		# PSU_CRF_APB_RST_FPD_TOP_DP_RESET                                                0X1

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00010000U ,0x00010000U)  */
    mask_write 0XFD1A0100 0x00010000 0x00010000
}

set psu_ps_pl_isolation_removal_data {
		# : PS-PL POWER UP REQUEST
		# Register : REQ_PWRUP_INT_EN @ 0XFFD80118</p>

		# Power-up Request Interrupt Enable for PL
		# PSU_PMU_GLOBAL_REQ_PWRUP_INT_EN_PL                                              1

		# Power-up Request Interrupt Enable Register. Writing a 1 to this location
    #  will unmask the interrupt.
		#(OFFSET, MASK, VALUE)      (0XFFD80118, 0x00800000U ,0x00800000U)  */
    mask_write 0XFFD80118 0x00800000 0x00800000
		# Register : REQ_PWRUP_TRIG @ 0XFFD80120</p>

		# Power-up Request Trigger for PL
		# PSU_PMU_GLOBAL_REQ_PWRUP_TRIG_PL                                                1

		# Power-up Request Trigger Register. A write of one to this location will
    # generate a power-up request to the PMU.
		#(OFFSET, MASK, VALUE)      (0XFFD80120, 0x00800000U ,0x00800000U)  */
    mask_write 0XFFD80120 0x00800000 0x00800000
		# : POLL ON PL POWER STATUS
		# Register : REQ_PWRUP_STATUS @ 0XFFD80110</p>

		# Power-up Request Status for PL
		# PSU_PMU_GLOBAL_REQ_PWRUP_STATUS_PL                                              1
    mask_poll 0XFFD80110 0x00800000 0x00000000
}

set psu_afi_config {
		# : AFI RESET
		# Register : RST_FPD_TOP @ 0XFD1A0100</p>

		# AF_FM0 block level reset
		# PSU_CRF_APB_RST_FPD_TOP_AFI_FM0_RESET                                           0

		# AF_FM1 block level reset
		# PSU_CRF_APB_RST_FPD_TOP_AFI_FM1_RESET                                           0

		# AF_FM2 block level reset
		# PSU_CRF_APB_RST_FPD_TOP_AFI_FM2_RESET                                           0

		# AF_FM3 block level reset
		# PSU_CRF_APB_RST_FPD_TOP_AFI_FM3_RESET                                           0

		# AF_FM4 block level reset
		# PSU_CRF_APB_RST_FPD_TOP_AFI_FM4_RESET                                           0

		# AF_FM5 block level reset
		# PSU_CRF_APB_RST_FPD_TOP_AFI_FM5_RESET                                           0

		# FPD Block level software controlled reset
		#(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00001F80U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x00001F80 0x00000000
		# Register : RST_LPD_TOP @ 0XFF5E023C</p>

		# AFI FM 6
		# PSU_CRL_APB_RST_LPD_TOP_AFI_FM6_RESET                                           0

		# Software control register for the LPD block.
		#(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00080000U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00080000 0x00000000
		# : AFIFM INTERFACE WIDTH
		# Register : afi_fs @ 0XFD615000</p>

		# Select the 32/64/128-bit data width selection for the Slave 0 00: 32-bit
    #  AXI data width (default) 01: 64-bit AXI data width 10: 128-bit AXI data
    #  width 11: reserved
		# PSU_FPD_SLCR_AFI_FS_DW_SS0_SEL                                                  0x2

		# Select the 32/64/128-bit data width selection for the Slave 1 00: 32-bit
    #  AXI data width (default) 01: 64-bit AXI data width 10: 128-bit AXI data
    #  width 11: reserved
		# PSU_FPD_SLCR_AFI_FS_DW_SS1_SEL                                                  0x2

		# afi fs SLCR control register. This register is static and should not be
    # modified during operation.
		#(OFFSET, MASK, VALUE)      (0XFD615000, 0x00000F00U ,0x00000A00U)  */
    mask_write 0XFD615000 0x00000F00 0x00000A00
}

set psu_ps_pl_reset_config_data {
		# : PS PL RESET SEQUENCE
		# : FABRIC RESET USING EMIO
		# Register : MASK_DATA_5_MSW @ 0XFF0A002C</p>

		# Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW]
		# PSU_GPIO_MASK_DATA_5_MSW_MASK_5_MSW                                             0x8000

		# Maskable Output Data (GPIO Bank5, EMIO, Upper 16bits)
		#(OFFSET, MASK, VALUE)      (0XFF0A002C, 0xFFFF0000U ,0x80000000U)  */
    mask_write 0XFF0A002C 0xFFFF0000 0x80000000
		# Register : DIRM_5 @ 0XFF0A0344</p>

		# Operation is the same as DIRM_0[DIRECTION_0]
		# PSU_GPIO_DIRM_5_DIRECTION_5                                                     0x80000000

		# Direction mode (GPIO Bank5, EMIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0344, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0344 0xFFFFFFFF 0x80000000
		# Register : OEN_5 @ 0XFF0A0348</p>

		# Operation is the same as OEN_0[OP_ENABLE_0]
		# PSU_GPIO_OEN_5_OP_ENABLE_5                                                      0x80000000

		# Output enable (GPIO Bank5, EMIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0348, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0348 0xFFFFFFFF 0x80000000
		# Register : DATA_5 @ 0XFF0A0054</p>

		# Output Data
		# PSU_GPIO_DATA_5_DATA_5                                                          0x80000000

		# Output Data (GPIO Bank5, EMIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0054, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0054 0xFFFFFFFF 0x80000000
    mask_delay 0x00000000 1
		# : FABRIC RESET USING DATA_5 TOGGLE
		# Register : DATA_5 @ 0XFF0A0054</p>

		# Output Data
		# PSU_GPIO_DATA_5_DATA_5                                                          0X00000000

		# Output Data (GPIO Bank5, EMIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0054, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFF0A0054 0xFFFFFFFF 0x00000000
    mask_delay 0x00000000 1
		# : FABRIC RESET USING DATA_5 TOGGLE
		# Register : DATA_5 @ 0XFF0A0054</p>

		# Output Data
		# PSU_GPIO_DATA_5_DATA_5                                                          0x80000000

		# Output Data (GPIO Bank5, EMIO)
		#(OFFSET, MASK, VALUE)      (0XFF0A0054, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0054 0xFFFFFFFF 0x80000000
}

proc psu_init {} {
    # save current mode
    set saved_mode [configparams force-mem-accesses]                  
    # force accesses
    configparams force-mem-accesses 1 
    variable psu_mio_init_data 
    variable psu_pll_init_data 
    variable psu_clock_init_data
	variable psu_ddr_init_data
    variable psu_peripherals_init_data
    variable psu_resetin_init_data
    variable psu_resetout_init_data
    variable psu_serdes_init_data
    variable psu_resetin_init_data
    variable psu_peripherals_powerdwn_data 
    variable psu_afi_config 

    init_ps [subst {$psu_mio_init_data $psu_pll_init_data $psu_clock_init_data $psu_ddr_init_data }]
    psu_ddr_phybringup_data 
    init_ps [subst {$psu_peripherals_init_data $psu_resetin_init_data }]
    init_serdes 
    init_ps [subst {$psu_serdes_init_data $psu_resetout_init_data }]
    init_peripheral 
    init_ps [subst {$psu_peripherals_powerdwn_data }]
    init_ps [subst {$psu_afi_config }]
    # restore original mode
    configparams force-mem-accesses $saved_mode                                       
}

proc psu_post_config {} {
    variable psu_post_config_data
    init_ps [subst {$psu_post_config_data}]
}

proc psu_ps_pl_reset_config {} {
    variable psu_ps_pl_reset_config_data
    init_ps [subst {$psu_ps_pl_reset_config_data}]
}

proc psu_ps_pl_isolation_removal {} {
    variable psu_ps_pl_isolation_removal_data
    init_ps [subst {$psu_ps_pl_isolation_removal_data}]
}


proc mask_read { addr mask } {
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set maskedval [expr {$curval & $mask}]
    return $maskedval
}


proc mask_poll { addr mask } {
    set count 1
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set maskedval [expr {$curval & $mask}]
    while { $maskedval == 0 } {
        set curval "0x[string range [mrd -force $addr] end-8 end]"
        set maskedval [expr {$curval & $mask}]
        set count [ expr { $count + 1 } ]
        if { $count == 1000 } {
          puts "Timeout Reached. Mask poll failed at ADDRESS: $addr MASK: $mask"
          break
        }
    }
}

proc psu_mask_write { addr mask value } {
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set curval [expr {$curval & ~($mask)}]
    set maskedval [expr {$value & $mask}]
    set maskedval [expr {$curval | $maskedval}]
    mwr -force $addr $maskedval
}

proc serdes_fixcal_code {} {
	
	set MaskStatus 1
	array set match_pmos_code {}
	array set match_nmos_code {}
	array set match_ical_code {}
	array set match_rcal_code {}
	set p_code 0
	set n_code 0
	set i_code 0
	set r_code 0
	set repeat_count 0
	set L3_TM_CALIB_DIG20 0
    set L3_TM_CALIB_DIG19 0
    set L3_TM_CALIB_DIG18 0
    set L3_TM_CALIB_DIG16 0
    set L3_TM_CALIB_DIG15 0
    set L3_TM_CALIB_DIG14 0

  set rdata 0
  
  set rdata [mask_read 0XFD40289C 0xFFFFFFFF] 
  set rdata [expr $rdata & ~0x03 ]
  set rdata [expr $rdata | 0x1]  
  mask_write 0XFD40289C 0xFFFFFFFF $rdata
  #check supply good status before starting AFE sequencing
  set count 1
  while 1 {
    set rdata [mask_read 0xFD402B1C 0xFFFFFFFF]
    set count [ expr { $count + 1 } ]
    if { [expr $rdata & 0x0000000E] == 0x0000000E } {
      break;
    }
    if { $count == 1000 } {
      break;
    }
  }


	for {set i 0} {$i<23 } {incr i } {
	   set match_pmos_code($i) 0;
	   set match_nmos_code($i) 0;
	}
	
	for {set i 0}  {$i<7} {incr i} {
 	   set match_ical_code($i) 0;
	   set match_rcal_code($i) 0;
    }
	
	while 1 {
      #Clear ICM_CFG value
      mask_write 0xFD410010 0xFFFFFFFF 0x00000000
      mask_write 0xFD410014 0xFFFFFFFF 0x00000000

      #Set ICM_CFG value
      #This will trigger recalibration of all stages
      mask_write 0xFD410010 0xFFFFFFFF 0x00000001
      mask_write 0xFD410014 0xFFFFFFFF 0x00000000;

      #is calibration done? polling on L3_CALIB_DONE_STATUS
      mask_poll 0xFD40EF14  0x2;
      
	  #PMOS code	
      set p_code [mask_read 0xFD40EF18 0xFFFFFFFF]; 
	  #NMOS code
      set n_code [mask_read 0xFD40EF1C 0xFFFFFFFF]; 
      #ICAL code 
      set i_code [mask_read 0xFD40EF24 0xFFFFFFFF]; 
	  #RX code
      set r_code [mask_read 0xFD40EF28 0xFFFFFFFF]; 
      

      #xil_printf("#SERDES initialization VALUES NMOS = 0x%x, PMOS = 0x%x, ICAL = 0x%x, RCAL = 0x%x\n\r", p_code, n_code, i_code, r_code);
	  #PMOS code in acceptable range 	
      if {($p_code >= 0x26) && ($p_code <= 0x3C)} {
    	  set index [expr $p_code - 0x26]
		  set value $match_pmos_code($index) 
		  incr value
		  set match_pmos_code($index) $value;
      }
	  #NMOS code in acceptable range	
      if {($n_code >= 0x26) && ($n_code <= 0x3C)} {
        set index [expr $n_code - 0x26]
        set value $match_nmos_code($index)
        incr value    	
		set match_nmos_code($index) $value;
      }
      #PMOS code in acceptable range
      if {($i_code >= 0xC) && ($i_code <= 0x12)} {
      
    	set index [expr $i_code - 0xC]
        set value $match_ical_code($index)
        incr value    	
		set match_ical_code($index) $value;
		
      }
      #NMOS code in acceptable range
      if {($r_code >= 0x6) && ($r_code <= 0xC)} {
    	set index [expr $r_code - 0x6]
        set value $match_rcal_code($index)
        incr value    	
		set match_rcal_code($index) $value;
      }
	  
	  incr repeat_count 	
      if {$repeat_count > 10} {
	    break
	  }
   } 
	
	
   #find the valid code which resulted in maximum times in 10 iterations
   for {set i 0 } {$i < 23}  {incr i} {
   
	   if {$match_pmos_code($i) >= $match_pmos_code(0) } {
		   set match_pmos_code(0)  $match_pmos_code($i)
		   set p_code [expr 0x26 + $i]
	   }
	   if {$match_nmos_code($i)  >= $match_nmos_code(0)} {
	   
		   set match_nmos_code(0) $match_nmos_code($i)
		   set n_code [expr 0x26 + $i];
	   }
   }

   for {set $i 0} {$i<7} {incr i} {
	   if {$match_ical_code($i) >= $match_ical_code(0)} {
		   set match_ical_code(0) $match_ical_code($i)
		   set i_code [expr 0xC + $i]
	   }
	   if {$match_rcal_code($i) >= $match_rcal_code(0)} {
		   set match_rcal_code(0) $match_rcal_code($i)
		   set r_code [expr 0x6 + $i]
	   }
   }
   #xil_printf("#SERDES initialization PASSED NMOS = 0x%x, PMOS = 0x%x, ICAL = 0x%x, RCAL = 0x%x\n\r", p_code, n_code, i_code, r_code);
   #L3_TM_CALIB_DIG20[3] PSW MSB Override
   #L3_TM_CALIB_DIG20[2:0]	PSW Code [4:2]
   #read DIG20
   set L3_TM_CALIB_DIG20 [mask_read 0xFD40EC50  0xFFFFFFF0]; 
   set L3_TM_CALIB_DIG20 [expr $L3_TM_CALIB_DIG20 | 0x8 | (($p_code>>2)&0x7)]


   #L3_TM_CALIB_DIG19[7:6]	PSW Code [1:0]
   #L3_TM_CALIB_DIG19[5]	PSW Override
   #L3_TM_CALIB_DIG19[2]	NSW MSB Override
   #L3_TM_CALIB_DIG19[1:0]	NSW Code [4:3]
   #read DIG19
   set L3_TM_CALIB_DIG19  [mask_read 0xFD40EC4C 0xFFFFFF18]
   set L3_TM_CALIB_DIG19  [expr $L3_TM_CALIB_DIG19 | (($p_code&0x3)<<6) | 0x20 | 0x4 | (($n_code>>3)&0x3)]

   #L3_TM_CALIB_DIG18[7:5]	NSW Code [2:0]
   #L3_TM_CALIB_DIG18[4]	NSW Override
   #read DIG18
   set L3_TM_CALIB_DIG18  [mask_read 0xFD40EC48 0xFFFFFF0F] 
   set L3_TM_CALIB_DIG18  [expr $L3_TM_CALIB_DIG18 | (($n_code&0x7)<<5) | 0x10]


   #L3_TM_CALIB_DIG16[2:0]	RX Code [3:1]
   #read DIG16
   set L3_TM_CALIB_DIG16  [mask_read 0xFD40EC40 0xFFFFFFF8]  
   set L3_TM_CALIB_DIG16  [expr $L3_TM_CALIB_DIG16 | (($r_code>>1)&0x7)]

   #L3_TM_CALIB_DIG15[7]	RX Code [0]
   #L3_TM_CALIB_DIG15[6]	RX CODE Override
   #L3_TM_CALIB_DIG15[3]	ICAL MSB Override
   #L3_TM_CALIB_DIG15[2:0]	ICAL Code [3:1]
   #read DIG15
   set L3_TM_CALIB_DIG15 [mask_read 0xFD40EC3C 0xFFFFFF30]
   set L3_TM_CALIB_DIG15 [expr $L3_TM_CALIB_DIG15 | (($r_code&0x1)<<7) | 0x40 | 0x8 | (($i_code>>1)&0x7)]

   #L3_TM_CALIB_DIG14[7]	ICAL Code [0]
   #L3_TM_CALIB_DIG14[6]	ICAL Override
   #read DIG14
   set L3_TM_CALIB_DIG14 [mask_read 0xFD40EC38 0xFFFFFF3F]
   set L3_TM_CALIB_DIG14 [expr $L3_TM_CALIB_DIG14 | (($i_code&0x1)<<7) | 0x40]

   #Forces the calibration values
   mask_write 0xFD40EC50 0xFFFFFFFF $L3_TM_CALIB_DIG20
   mask_write 0xFD40EC4C 0xFFFFFFFF $L3_TM_CALIB_DIG19
   mask_write 0xFD40EC48 0xFFFFFFFF $L3_TM_CALIB_DIG18
   mask_write 0xFD40EC40 0xFFFFFFFF $L3_TM_CALIB_DIG16
   mask_write 0xFD40EC3C 0xFFFFFFFF $L3_TM_CALIB_DIG15
   mask_write 0xFD40EC38 0xFFFFFFFF $L3_TM_CALIB_DIG14 


   return $MaskStatus;
 }
proc serdes_enb_coarse_saturation {} { 
   #/* 
   # * Enable PLL Coarse Code saturation Logic
   # */
   mask_write 0xFD402094 0xFFFFFFFF 0x00000010 
   mask_write 0xFD406094 0xFFFFFFFF 0x00000010 
   mask_write 0xFD40A094 0xFFFFFFFF 0x00000010 
   mask_write 0xFD40E094 0xFFFFFFFF 0x00000010

}

proc init_serdes {} {
  serdes_fixcal_code
  serdes_enb_coarse_saturation

}

proc poll { addr mask data} {
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set maskedval [expr {$curval & $mask}]
    set count 1
    while { $maskedval != $data } {
        set curval "0x[string range [mrd -force $addr] end-8 end]"
        set maskedval [expr {$curval & $mask}]
        set count [ expr { $count + 1 } ]
        if { $count == 100000000 } {
          puts "Timeout Reached. Mask poll failed at ADDRESS: $addr MASK: $mask"
          break
        }
    }
}

proc init_peripheral {} {
#SMMU_REG Interrrupt Enable: Followig register need to be written all the time to properly catch SMMU messages.
   mask_write 0xFD5F0018 0x8000001F 0x8000001F 
}
proc psu_init_xppu_aper_ram {} {

}


proc psu_lpd_protection {} {
}

proc psu_ddr_protection {} {
    set saved_mode [configparams force-mem-accesses]                  
    configparams force-mem-accesses 1 
    
    variable psu_ddr_xmpu0_data
    variable psu_ddr_xmpu1_data
    variable psu_ddr_xmpu2_data
    variable psu_ddr_xmpu3_data
    variable psu_ddr_xmpu4_data
    variable psu_ddr_xmpu5_data
    init_ps [subst {$psu_ddr_xmpu0_data  $psu_ddr_xmpu1_data  $psu_ddr_xmpu2_data  $psu_ddr_xmpu3_data  $psu_ddr_xmpu4_data  $psu_ddr_xmpu5_data}]
    
	configparams force-mem-accesses $saved_mode                                       
}

proc psu_ocm_protection {} {
    set saved_mode [configparams force-mem-accesses]                  
    configparams force-mem-accesses 1 
    
    variable psu_ocm_xmpu_data
    init_ps [subst {$psu_ocm_xmpu_data }]
    
	configparams force-mem-accesses $saved_mode                                       
}

proc psu_fpd_protection {} {
    set saved_mode [configparams force-mem-accesses]                  
    configparams force-mem-accesses 1 
    
	variable psu_fpd_xmpu_data
    init_ps [subst {$psu_fpd_xmpu_data }]
    
	configparams force-mem-accesses $saved_mode                                       
}

proc psu_protection_lock {} {
    set saved_mode [configparams force-mem-accesses]                  
    configparams force-mem-accesses 1 
    
	variable psu_protection_lock_data
    init_ps [subst {$psu_protection_lock_data }]
    
	configparams force-mem-accesses $saved_mode                                       
}

proc psu_protection {} {
  variable psu_apply_master_tz
   init_ps [subst {$psu_apply_master_tz }]
   psu_ddr_protection
   psu_ocm_protection
   psu_fpd_protection
   psu_lpd_protection
}

proc psu_ddr_phybringup_data {} {
mwr -force  0xFD080004 0x00040073

poll 0xFD080030 0x0000000F 0x0000000F  
	psu_mask_write 0xFD080004 0x00000001 0x00000001
#poll for PHY initialization to complete 
poll 0xFD080030 0x000000FF 0x0000001F 

	psu_mask_write 0xFD070010 0x00000008 0x00000008
	psu_mask_write 0xFD0701B0 0x00000001 0x00000001
	psu_mask_write 0xFD070010 0x00000030 0x00000010
	psu_mask_write 0xFD070010 0x00000001 0x00000000
	psu_mask_write 0xFD070010 0x0000F000 0x00006000
	psu_mask_write 0xFD070014 0x0003FFFF 0x00000819
	psu_mask_write 0xFD070010 0x80000000 0x80000000
poll 0xFD070018 0x00000001 0 
	psu_mask_write 0xFD070010 0x00000030 0x00000010
	psu_mask_write 0xFD070010 0x00000001 0x00000000
	psu_mask_write 0xFD070010 0x0000F000 0x00006000
	psu_mask_write 0xFD070014 0x0003FFFF 0x00000899
	psu_mask_write 0xFD070010 0x80000000 0x80000000
poll 0xFD070018 0x00000001 0 
	psu_mask_write 0xFD070010 0x00000030 0x00000010
	psu_mask_write 0xFD070010 0x00000001 0x00000000
	psu_mask_write 0xFD070010 0x0000F000 0x00006000
	psu_mask_write 0xFD070014 0x0003FFFF 0x00000819
	psu_mask_write 0xFD070010 0x80000000 0x80000000
poll 0xFD070018 0x00000001 0 
	psu_mask_write 0xFD070010 0x00000008 0x00000000
mwr -force  0xFD0701B0 0x00000001
mwr -force  0xFD070320 0x00000001
#//poll for DDR initialization to complete 
poll 0xFD070004 0x0000000F 0x00000001 

	psu_mask_write 0xFD080014 0x00000040 0x00000040
#Dummy reads before PHY training starts
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
psu_mask_write 0xFD080004 0xFFFFFFFF 0x0004FE01
 #trigger PHY training 
poll 0xFD080030 0x00000FFF 0x00000FFF
 
  #Poll PUB_PGSR0 for Trng complete  


 # Run Vref training in static read mode  
mwr -force  0xFD080200 0x100091C7
mwr -force  0xFD080018 0x00F01EEF
	psu_mask_write 0xFD08142C 0x00000030 0x00000030
	psu_mask_write 0xFD08146C 0x00000030 0x00000030
	psu_mask_write 0xFD0814AC 0x00000030 0x00000030
	psu_mask_write 0xFD0814EC 0x00000030 0x00000030
	psu_mask_write 0xFD08152C 0x00000030 0x00000030
psu_mask_write 0xFD080004 0xFFFFFFFF 0x00060001
  
 #trigger VreFPHY training 
poll 0xFD080030 0x00004001 0x00004001
     
 #//Poll PUB_PGSR0 for Trng complete  
mwr -force  0xFD080200 0x800091C7
mwr -force  0xFD080018 0x00F122E7
	psu_mask_write 0xFD08142C 0x00000030 0x00000000
	psu_mask_write 0xFD08146C 0x00000030 0x00000000
	psu_mask_write 0xFD0814AC 0x00000030 0x00000000
	psu_mask_write 0xFD0814EC 0x00000030 0x00000000
	psu_mask_write 0xFD08152C 0x00000030 0x00000000
psu_mask_write 0xFD080004 0xFFFFFFFF 0x0000C001
  
 #trigger VreFPHY training 
poll 0xFD080030 0x00000C01 0x00000C01
     
 #//Poll PUB_PGSR0 for Trng complete  
mwr -force  0xFD070180 0x01000040
mwr -force  0xFD070060 0x00000000
	psu_mask_write 0xFD080014 0x00000040 0x00000000

 
}