/* ----------------------------------------------------------------------------
 *         SAM Software Package License
 * ----------------------------------------------------------------------------
 * Copyright (c) 2011, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/** \addtogroup acc_module Working with ACC
 *  \ingroup peripherals_module
 * The ACC driver provides the interface to configure and use the ACC
 * peripheral.\n
 *
 * It applies comparison on two inputs and gives a compare output.
 *
 * To Enable a ACC Comparison,the user has to follow these few steps:
 * <ul>
 * <li> Enable ACC peripheral clock by setting the corresponding bit in 
 *     PMC_PCER1 (PMC Peripheral Clock Enable Register 1)
 * </li>
 * <li> Reset the controller by asserting ACC_CR_SWRST in ACC_CR(ACC Control 
 * Register) </li>
 * <li> Configure the mode as following steps:  </li>
 * -#   Select inputs for SELMINUS and SELPLUS in ACC_MR (ACC Mode Register).
 * -#   Enable Analog Comparator by setting ACEN in ACC_MR.
 * -#   Configure Edge Type to detect different compare output.
 * </li>
 * <li> Wait until the automatic mask period expires by polling MASK bit in
 *      ACC_ISR.
 * </ul>
 *
 * For more accurate information, please look at the ACC section of the
 * Datasheet.
 *
 * Related files :\n
 * \ref acc.c\n
 * \ref acc.h\n
 */
/*@{*/
/*@}*/
/**
 * \file
 *
 * Implementation of Analog Comparator Controller (ACC).
 *
 */
/*----------------------------------------------------------------------------
 *        Headers
 *----------------------------------------------------------------------------*/

#include "chip.h"

/*----------------------------------------------------------------------------
 *        Exported functions
 *----------------------------------------------------------------------------*/

/**
 * \brief Initialize the ACC controller
 *
 * \param pAcc Pointer to an Acc instance.
 * \param idAcc ACC identifier
 * \param ucSelplus input connected to inp, 0~7
 * \param ucSelminus input connected to inm,0~7
 * \param wAc_en Analog comparator enabled/disabled
 * \param wEdge CF flag triggering mode
 * \param wInvert INVert comparator output,use pattern defined in the device 
 * header file
 */
extern void ACC_Configure( Acc *pAcc, uint8_t idAcc, uint8_t ucSelplus, 
		uint8_t ucSelminus, uint16_t wAc_en, uint16_t wEdge, uint16_t wInvert )
{
	/* Enable peripheral clock*/
	PMC->PMC_PCER1 = 1 << (idAcc - 32) ;

	/*  Reset the controller */
	pAcc->ACC_CR |= ACC_CR_SWRST ;

	/*  Write to the MR register */
	ACC_CfgModeReg( pAcc,
			( (ucSelplus<<ACC_MR_SELPLUS_Pos) & ACC_MR_SELPLUS_Msk ) |
			( (ucSelminus<<ACC_MR_SELMINUS_Pos) & ACC_MR_SELMINUS_Msk ) |
			( (wAc_en<<8) & ACC_MR_ACEN ) |
			( (wEdge<<ACC_MR_EDGETYP_Pos) & ACC_MR_EDGETYP_Msk ) |
			( (wInvert<<12) & ACC_MR_INV ) ) ;
	/* set hysteresis and current option*/
	pAcc->ACC_ACR = (ACC_ACR_ISEL_HISP 
			| ((0x01 << ACC_ACR_HYST_Pos) & ACC_ACR_HYST_Msk));

	/* Automatic Output Masking Period*/
	while ( pAcc->ACC_ISR & (uint32_t)ACC_ISR_MASK ) ;
}

/**
 * Return the Channel Converted Data
 * \param pAcc Pointer to an Acc instance.
 * \param ucSelplus input applied on ACC SELPLUS
 * \param ucSelminus input applied on ACC SELMINUS
 */
extern void ACC_SetComparisonPair( Acc *pAcc, uint8_t ucSelplus, uint8_t ucSelminus )
{
	uint32_t dwTemp ;

	assert( ucSelplus < 8 && ucSelminus < 8 ) ;

	dwTemp = pAcc->ACC_MR ;
	pAcc->ACC_MR = 
		dwTemp & (uint32_t) ((~ACC_MR_SELMINUS_Msk) & (~ACC_MR_SELPLUS_Msk));

	pAcc->ACC_MR |= ( ((ucSelplus << ACC_MR_SELPLUS_Pos) & ACC_MR_SELPLUS_Msk) |
			((ucSelminus << ACC_MR_SELMINUS_Pos) & ACC_MR_SELMINUS_Msk) ) ;
}

/**
 * Return Comparison Result
 * \param pAcc Pointer to an Acc instance.
 * \param dwStatus value of ACC_ISR
 */
extern uint32_t ACC_GetComparisonResult( Acc *pAcc, uint32_t dwStatus )
{
	uint32_t dwTemp = pAcc->ACC_MR ;

	if ( (dwTemp & ACC_MR_INV) == ACC_MR_INV )	{
		if ( dwStatus & ACC_ISR_SCO ) {
			return 0 ; /* inn>inp*/
		} else {
			return 1 ;/* inp>inn*/
		}
	} else {
		if ( dwStatus & ACC_ISR_SCO ) {
			return 1 ; /* inp>inn*/
		} else {
			return 0 ;/* inn>inp*/
		}
	}
}