FreeRTOS/Demo/CORTEX_M7_SAMV71_Xplained_AtmelStudio/libchip_samv7/source/efc.c

/* ----------------------------------------------------------------------------
 *         SAM Software Package License
 * ----------------------------------------------------------------------------
 * Copyright (c) 2012, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/** \addtogroup efc_module Working with EEFC
 *
 * The EEFC driver provides the interface to configure and use the EEFC
 * peripheral.
 *
 * The user needs to set the number of wait states depending on the frequency
 * used.\n
 * Configure number of cycles for flash read/write operations in the FWS field 
 * of EEFC_FMR.
 *
 * It offers a function to send flash command to EEFC and waits for the
 * flash to be ready.
 *
 * To send flash command, the user could do in either of following way:
 * <ul>
 * <li>Write a correct key, command and argument in EEFC_FCR. </li>
 * <li>Or, Use IAP (In Application Programming) function which is executed from
 * ROM directly, this allows flash programming to be done by code running in 
 * flash.</li>
 * <li>Once the command is achieved, it can be detected even by polling 
 * EEFC_FSR or interrupt.
 * </ul>
 *
 * The command argument could be a page number,GPNVM number or nothing, it 
 * depends on the command itself. Some useful functions in this driver could 
 * help user translate physical flash address into a page number and vice verse.
 *
 * For more accurate information, please look at the EEFC section of the
 * Datasheet.
 *
 * Related files :\n
 * \ref efc.c\n
 * \ref efc.h.\n
 */
/*@{*/
/*@}*/


/**
 * \file
 *
 * Implementation of Enhanced Embedded Flash Controller (EEFC).
 *
 */


/*----------------------------------------------------------------------------
 *        Headers
 *----------------------------------------------------------------------------*/
#include "chip.h"

#include <assert.h>

 
/*----------------------------------------------------------------------------
 *        Macro 
 *----------------------------------------------------------------------------*/
#define EEFC_FCR_FCMD(value) ((EEFC_FCR_FCMD_Msk & ((value) << EEFC_FCR_FCMD_Pos)))

/*----------------------------------------------------------------------------
 *        Exported functions
 *----------------------------------------------------------------------------*/

extern void EFC_WriteFMR( Efc* efc, uint32_t dwFmr );

#ifdef __ICCARM__
extern __ramfunc void EFC_WriteFMR( Efc* efc, uint32_t dwFmr )
#else
	__attribute__ ((section (".ramfunc")))
extern void EFC_WriteFMR( Efc* efc, uint32_t dwFmr )
#endif
{
	efc->EEFC_FMR = dwFmr;
}

/**
 * \brief Enables the flash ready interrupt source on the EEFC peripheral.
 *
 * \param efc  Pointer to a Efc instance
 */
extern void EFC_EnableFrdyIt( Efc* efc )
{
	uint32_t dwFmr;

	dwFmr = efc->EEFC_FMR |= EEFC_FMR_FRDY;
	EFC_WriteFMR(efc, dwFmr);
}

/**
 * \brief Disables the flash ready interrupt source on the EEFC peripheral.
 *
 * \param efc  Pointer to a Efc instance
 */
extern void EFC_DisableFrdyIt( Efc* efc )
{
	uint32_t dwFmr;

	dwFmr = efc->EEFC_FMR & (~EEFC_FMR_FRDY);
	EFC_WriteFMR(efc, dwFmr);
}


/**
 * \brief Set read/write wait state on the EEFC peripheral.
 *
 * \param efc  Pointer to a Efc instance
 * \param cycles  the number of wait states in cycle.
 */
extern void EFC_SetWaitState( Efc* efc, uint8_t ucCycles )
{
	uint32_t dwFmr ;

	dwFmr = efc->EEFC_FMR ;
	dwFmr &= ~((uint32_t)EEFC_FMR_FWS_Msk) ;
	dwFmr |= EEFC_FMR_FWS(ucCycles);
	EFC_WriteFMR(efc, dwFmr);
}

/**
 * \brief Returns the current status of the EEFC.
 *
 * \note Keep in mind that this function clears the value of some status bits 
 * (LOCKE, PROGE).
 *
 * \param efc  Pointer to a Efc instance
 */
extern uint32_t EFC_GetStatus( Efc* efc )
{
	return efc->EEFC_FSR ;
}

/**
 * \brief Returns the result of the last executed command.
 *
 * \param efc  Pointer to a Efc instance
 */
extern uint32_t EFC_GetResult( Efc* efc )
{
	return efc->EEFC_FRR ;
}

/**
 * \brief Translates the given address page and offset values.
 * \note The resulting values are stored in the provided variables if they are
 * not null.
 *
 * \param efc  Pointer to a Efc instance
 * \param address  Address to translate.
 * \param pPage  First page accessed.
 * \param pOffset  Byte offset in first page.
 */
extern void EFC_TranslateAddress( Efc** ppEfc, uint32_t dwAddress, uint16_t* pwPage,
								uint16_t* pwOffset )
{
	assert( dwAddress >= IFLASH_ADDR ) ;
	assert( dwAddress <= (IFLASH_ADDR + IFLASH_SIZE) ) ;

	/* Store values */
	if ( ppEfc )	{
		*ppEfc = EFC ;
	}

	if ( pwPage ) {
		*pwPage = (dwAddress - IFLASH_ADDR) / IFLASH_PAGE_SIZE ;
	}

	if ( pwOffset ) {
		*pwOffset = (dwAddress - IFLASH_ADDR) % IFLASH_PAGE_SIZE; ;
	}
}


/**
 * \brief Computes the address of a flash access given the page and offset.
 *
 * \param efc  Pointer to a Efc instance
 * \param page  Page number.
 * \param offset  Byte offset inside page.
 * \param pAddress  Computed address (optional).
 */
extern void EFC_ComputeAddress( Efc *efc, uint16_t wPage, uint16_t wOffset,
							uint32_t *pdwAddress )
{
	uint32_t dwAddress ;

	/* Stop warning */
	efc = efc;

	assert( efc ) ;
	assert( wPage <= IFLASH_NB_OF_PAGES ) ;
	assert( wOffset < IFLASH_PAGE_SIZE ) ;
	dwAddress = IFLASH_ADDR + wPage * IFLASH_PAGE_SIZE + wOffset ;

	/* Store result */
	if ( pdwAddress != NULL ) {
		*pdwAddress = dwAddress ;
	}
}

/**
 * \brief Performs the given command and wait until its completion (or an error).
 *
 * \param efc  Pointer to a Efc instance
 * \param command  Command to perform.
 * \param argument  Optional command argument.
 *
 * \return 0 if successful, otherwise returns an error code.
 */

extern uint32_t EFC_PerformCommand( Efc* efc, uint32_t dwCommand, 
								uint32_t dwArgument, uint32_t dwUseIAP )
{
	if ( dwUseIAP != 0 ) {
		/* Pointer on IAP function in ROM */
		static uint32_t (*IAP_PerformCommand)( uint32_t, uint32_t ) ;

		IAP_PerformCommand = (uint32_t (*)( uint32_t, uint32_t )) 
				*((uint32_t*)CHIP_FLASH_IAP_ADDRESS ) ;
		if (efc == EFC) {
			IAP_PerformCommand( 0, EEFC_FCR_FKEY_PASSWD | EEFC_FCR_FARG(dwArgument) 
					| EEFC_FCR_FCMD(dwCommand) ) ;
		}
		return (efc->EEFC_FSR & (EEFC_FSR_FLOCKE | EEFC_FSR_FCMDE | EEFC_FSR_FLERR)) ;
	} else {
		uint32_t dwStatus ;

		efc->EEFC_FCR = EEFC_FCR_FKEY_PASSWD | EEFC_FCR_FARG(dwArgument) 
				| EEFC_FCR_FCMD(dwCommand) ;
		do {
			dwStatus = efc->EEFC_FSR ;
		}
		while ( (dwStatus & EEFC_FSR_FRDY) != EEFC_FSR_FRDY ) ;

		return ( dwStatus & (EEFC_FSR_FLOCKE | EEFC_FSR_FCMDE | EEFC_FSR_FLERR) ) ;
	}
}

/**
 * \brief Set flash access mode.
 *
 * \param dwMode - 0:128-bit, (1<<24):64-bit
 */
extern void EFC_SetFlashAccessMode(Efc* efc, uint32_t dwMode)
{
	uint32_t dwFmr;

	dwFmr = dwMode;
	EFC_WriteFMR(efc, dwFmr);
}