/*
 * FreeRTOS Kernel V10.3.0
 * Copyright (C) 2020 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy of
 * this software and associated documentation files (the "Software"), to deal in
 * the Software without restriction, including without limitation the rights to
 * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
 * the Software, and to permit persons to whom the Software is furnished to do so,
 * subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in all
 * copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
 * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
 * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
 * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
 * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
 *
 * http://www.FreeRTOS.org
 * http://aws.amazon.com/freertos
 *
 * 1 tab == 4 spaces!
 */

/*
	The tasks defined on this page demonstrate the use of recursive mutexes.

	For recursive mutex functionality the created mutex should be created using
	xSemaphoreCreateRecursiveMutex(), then be manipulated
	using the xSemaphoreTakeRecursive() and xSemaphoreGiveRecursive() API
	functions.

	This demo creates three tasks all of which access the same recursive mutex:

	prvRecursiveMutexControllingTask() has the highest priority so executes
	first and grabs the mutex.  It then performs some recursive accesses -
	between each of which it sleeps for a short period to let the lower
	priority tasks execute.  When it has completed its demo functionality
	it gives the mutex back before suspending itself.

	prvRecursiveMutexBlockingTask() attempts to access the mutex by performing
	a blocking 'take'.  The blocking task has a lower priority than the
	controlling	task so by the time it executes the mutex has already been
	taken by the controlling task,  causing the blocking task to block.  It
	does not unblock until the controlling task has given the mutex back,
	and it does not actually run until the controlling task has suspended
	itself (due to the relative priorities).  When it eventually does obtain
	the mutex all it does is give the mutex back prior to also suspending
	itself.  At this point both the controlling task and the blocking task are
	suspended.

	prvRecursiveMutexPollingTask() runs at the idle priority.  It spins round
	a tight loop attempting to obtain the mutex with a non-blocking call.  As
	the lowest priority task it will not successfully obtain the mutex until
	both the controlling and blocking tasks are suspended.  Once it eventually
	does obtain the mutex it first unsuspends both the controlling task and
	blocking task prior to giving the mutex back - resulting in the polling
	task temporarily inheriting the controlling tasks priority.
*/

/* Scheduler include files. */
#include "FreeRTOS.h"
#include "task.h"
#include "semphr.h"

/* Demo app include files. */
#include "recmutex.h"

/* Priorities assigned to the three tasks.  recmuCONTROLLING_TASK_PRIORITY can
be overridden by a definition in FreeRTOSConfig.h. */
#ifndef recmuCONTROLLING_TASK_PRIORITY
	#define recmuCONTROLLING_TASK_PRIORITY	( tskIDLE_PRIORITY + 2 )
#endif
#define recmuBLOCKING_TASK_PRIORITY		( tskIDLE_PRIORITY + 1 )
#define recmuPOLLING_TASK_PRIORITY		( tskIDLE_PRIORITY + 0 )

/* The recursive call depth. */
#define recmuMAX_COUNT					( 10 )

/* Misc. */
#define recmuSHORT_DELAY				( pdMS_TO_TICKS( 20 ) )
#define recmuNO_DELAY					( ( TickType_t ) 0 )
#define recmu15ms_DELAY					( pdMS_TO_TICKS( 15 ) )

#ifndef recmuRECURSIVE_MUTEX_TEST_TASK_STACK_SIZE
	#define recmuRECURSIVE_MUTEX_TEST_TASK_STACK_SIZE configMINIMAL_STACK_SIZE
#endif

/* The three tasks as described at the top of this file. */
static void prvRecursiveMutexControllingTask( void *pvParameters );
static void prvRecursiveMutexBlockingTask( void *pvParameters );
static void prvRecursiveMutexPollingTask( void *pvParameters );

/* The mutex used by the demo. */
static SemaphoreHandle_t xMutex;

/* Variables used to detect and latch errors. */
static volatile BaseType_t xErrorOccurred = pdFALSE, xControllingIsSuspended = pdFALSE, xBlockingIsSuspended = pdFALSE;
static volatile UBaseType_t uxControllingCycles = 0, uxBlockingCycles = 0, uxPollingCycles = 0;

/* Handles of the two higher priority tasks, required so they can be resumed
(unsuspended). */
static TaskHandle_t xControllingTaskHandle, xBlockingTaskHandle;

/*-----------------------------------------------------------*/

void vStartRecursiveMutexTasks( void )
{
	/* Just creates the mutex and the three tasks. */

	xMutex = xSemaphoreCreateRecursiveMutex();

	if( xMutex != NULL )
	{
		/* vQueueAddToRegistry() adds the mutex to the registry, if one is
		in use.  The registry is provided as a means for kernel aware
		debuggers to locate mutex and has no purpose if a kernel aware debugger
		is not being used.  The call to vQueueAddToRegistry() will be removed
		by the pre-processor if configQUEUE_REGISTRY_SIZE is not defined or is
		defined to be less than 1. */
		vQueueAddToRegistry( ( QueueHandle_t ) xMutex, "Recursive_Mutex" );

		xTaskCreate( prvRecursiveMutexControllingTask, "Rec1", recmuRECURSIVE_MUTEX_TEST_TASK_STACK_SIZE, NULL, recmuCONTROLLING_TASK_PRIORITY, &xControllingTaskHandle );
		xTaskCreate( prvRecursiveMutexBlockingTask, "Rec2", recmuRECURSIVE_MUTEX_TEST_TASK_STACK_SIZE, NULL, recmuBLOCKING_TASK_PRIORITY, &xBlockingTaskHandle );
		xTaskCreate( prvRecursiveMutexPollingTask, "Rec3", recmuRECURSIVE_MUTEX_TEST_TASK_STACK_SIZE, NULL, recmuPOLLING_TASK_PRIORITY, NULL );
	}
}
/*-----------------------------------------------------------*/

static void prvRecursiveMutexControllingTask( void *pvParameters )
{
UBaseType_t ux;

	/* Just to remove compiler warning. */
	( void ) pvParameters;

	for( ;; )
	{
		/* Should not be able to 'give' the mutex, as we have not yet 'taken'
		it.   The first time through, the mutex will not have been used yet,
		subsequent times through, at this point the mutex will be held by the
		polling task. */
		if( xSemaphoreGiveRecursive( xMutex ) == pdPASS )
		{
			xErrorOccurred = pdTRUE;
		}

		for( ux = 0; ux < recmuMAX_COUNT; ux++ )
		{
			/* We should now be able to take the mutex as many times as
			we like.

			The first time through the mutex will be immediately available, on
			subsequent times through the mutex will be held by the polling task
			at this point and this Take will cause the polling task to inherit
			the priority of this task.  In this case the block time must be
			long enough to ensure the polling task will execute again before the
			block time expires.  If the block time does expire then the error
			flag will be set here. */
			if( xSemaphoreTakeRecursive( xMutex, recmu15ms_DELAY ) != pdPASS )
			{
				xErrorOccurred = pdTRUE;
			}

			/* Ensure the other task attempting to access the mutex (and the
			other demo tasks) are able to execute to ensure they either block
			(where a block time is specified) or return an error (where no
			block time is specified) as the mutex is held by this task. */
			vTaskDelay( recmuSHORT_DELAY );
		}

		/* For each time we took the mutex, give it back. */
		for( ux = 0; ux < recmuMAX_COUNT; ux++ )
		{
			/* Ensure the other task attempting to access the mutex (and the
			other demo tasks) are able to execute. */
			vTaskDelay( recmuSHORT_DELAY );

			/* We should now be able to give the mutex as many times as we
			took it.  When the mutex is available again the Blocking task
			should be unblocked but not run because it has a lower priority
			than this task.  The polling task should also not run at this point
			as it too has a lower priority than this task. */
			if( xSemaphoreGiveRecursive( xMutex ) != pdPASS )
			{
				xErrorOccurred = pdTRUE;
			}

			#if( configUSE_PREEMPTION == 0 )
				taskYIELD();
			#endif
		}

		/* Having given it back the same number of times as it was taken, we
		should no longer be the mutex owner, so the next give should fail. */
		if( xSemaphoreGiveRecursive( xMutex ) == pdPASS )
		{
			xErrorOccurred = pdTRUE;
		}

		/* Keep count of the number of cycles this task has performed so a
		stall can be detected. */
		uxControllingCycles++;

		/* Suspend ourselves so the blocking task can execute. */
		xControllingIsSuspended = pdTRUE;
		vTaskSuspend( NULL );
		xControllingIsSuspended = pdFALSE;
	}
}
/*-----------------------------------------------------------*/

static void prvRecursiveMutexBlockingTask( void *pvParameters )
{
	/* Just to remove compiler warning. */
	( void ) pvParameters;

	for( ;; )
	{
		/* This task will run while the controlling task is blocked, and the
		controlling task will block only once it has the mutex - therefore
		this call should block until the controlling task has given up the
		mutex, and not actually execute	past this call until the controlling
		task is suspended.  portMAX_DELAY - 1 is used instead of portMAX_DELAY
		to ensure the task's state is reported as Blocked and not Suspended in
		a later call to configASSERT() (within the polling task). */
		if( xSemaphoreTakeRecursive( xMutex, ( portMAX_DELAY - 1 ) ) == pdPASS )
		{
			if( xControllingIsSuspended != pdTRUE )
			{
				/* Did not expect to execute until the controlling task was
				suspended. */
				xErrorOccurred = pdTRUE;
			}
			else
			{
				/* Give the mutex back before suspending ourselves to allow
				the polling task to obtain the mutex. */
				if( xSemaphoreGiveRecursive( xMutex ) != pdPASS )
				{
					xErrorOccurred = pdTRUE;
				}

				xBlockingIsSuspended = pdTRUE;
				vTaskSuspend( NULL );
				xBlockingIsSuspended = pdFALSE;
			}
		}
		else
		{
			/* We should not leave the xSemaphoreTakeRecursive() function
			until the mutex was obtained. */
			xErrorOccurred = pdTRUE;
		}

		/* The controlling and blocking tasks should be in lock step. */
		if( uxControllingCycles != ( uxBlockingCycles + 1 ) )
		{
			xErrorOccurred = pdTRUE;
		}

		/* Keep count of the number of cycles this task has performed so a
		stall can be detected. */
		uxBlockingCycles++;
	}
}
/*-----------------------------------------------------------*/

static void prvRecursiveMutexPollingTask( void *pvParameters )
{
	/* Just to remove compiler warning. */
	( void ) pvParameters;

	for( ;; )
	{
		/* Keep attempting to obtain the mutex.  It should only be obtained when
		the blocking task has suspended itself, which in turn should only
		happen when the controlling task is also suspended. */
		if( xSemaphoreTakeRecursive( xMutex, recmuNO_DELAY ) == pdPASS )
		{
			#if( INCLUDE_eTaskGetState == 1 )
			{
				configASSERT( eTaskGetState( xControllingTaskHandle ) == eSuspended );
				configASSERT( eTaskGetState( xBlockingTaskHandle ) == eSuspended );
			}
			#endif /* INCLUDE_eTaskGetState */

			/* Is the blocking task suspended? */
			if( ( xBlockingIsSuspended != pdTRUE ) || ( xControllingIsSuspended != pdTRUE ) )
			{
				xErrorOccurred = pdTRUE;
			}
			else
			{
				/* Keep count of the number of cycles this task has performed
				so a stall can be detected. */
				uxPollingCycles++;

				/* We can resume the other tasks here even though they have a
				higher priority than the polling task.  When they execute they
				will attempt to obtain the mutex but fail because the polling
				task is still the mutex holder.  The polling task (this task)
				will then inherit the higher priority.  The Blocking task will
				block indefinitely when it attempts to obtain the mutex, the
				Controlling task will only block for a fixed period and an
				error will be latched if the polling task has not returned the
				mutex by the time this fixed period has expired. */
				vTaskResume( xBlockingTaskHandle );
				#if( configUSE_PREEMPTION == 0 )
					taskYIELD();
				#endif

				vTaskResume( xControllingTaskHandle );
				#if( configUSE_PREEMPTION == 0 )
					taskYIELD();
				#endif

				/* The other two tasks should now have executed and no longer
				be suspended. */
				if( ( xBlockingIsSuspended == pdTRUE ) || ( xControllingIsSuspended == pdTRUE ) )
				{
					xErrorOccurred = pdTRUE;
				}

				#if( INCLUDE_uxTaskPriorityGet == 1 )
				{
					/* Check priority inherited. */
					configASSERT( uxTaskPriorityGet( NULL ) == recmuCONTROLLING_TASK_PRIORITY );
				}
				#endif /* INCLUDE_uxTaskPriorityGet */

				#if( INCLUDE_eTaskGetState == 1 )
				{
					configASSERT( eTaskGetState( xControllingTaskHandle ) == eBlocked );
					configASSERT( eTaskGetState( xBlockingTaskHandle ) == eBlocked );
				}
				#endif /* INCLUDE_eTaskGetState */

				/* Release the mutex, disinheriting the higher priority again. */
				if( xSemaphoreGiveRecursive( xMutex ) != pdPASS )
				{
					xErrorOccurred = pdTRUE;
				}

				#if( INCLUDE_uxTaskPriorityGet == 1 )
				{
					/* Check priority disinherited. */
					configASSERT( uxTaskPriorityGet( NULL ) == recmuPOLLING_TASK_PRIORITY );
				}
				#endif /* INCLUDE_uxTaskPriorityGet */
			}
		}

		#if configUSE_PREEMPTION == 0
		{
			taskYIELD();
		}
		#endif
	}
}
/*-----------------------------------------------------------*/

/* This is called to check that all the created tasks are still running. */
BaseType_t xAreRecursiveMutexTasksStillRunning( void )
{
BaseType_t xReturn;
static UBaseType_t uxLastControllingCycles = 0, uxLastBlockingCycles = 0, uxLastPollingCycles = 0;

	/* Is the controlling task still cycling? */
	if( uxLastControllingCycles == uxControllingCycles )
	{
		xErrorOccurred = pdTRUE;
	}
	else
	{
		uxLastControllingCycles = uxControllingCycles;
	}

	/* Is the blocking task still cycling? */
	if( uxLastBlockingCycles == uxBlockingCycles )
	{
		xErrorOccurred = pdTRUE;
	}
	else
	{
		uxLastBlockingCycles = uxBlockingCycles;
	}

	/* Is the polling task still cycling? */
	if( uxLastPollingCycles == uxPollingCycles )
	{
		xErrorOccurred = pdTRUE;
	}
	else
	{
		uxLastPollingCycles = uxPollingCycles;
	}

	if( xErrorOccurred == pdTRUE )
	{
		xReturn = pdFAIL;
	}
	else
	{
		xReturn = pdPASS;
	}

	return xReturn;
}