| /** |
| ****************************************************************************** |
| * @file stm32f2xx_hal_adc_ex.h |
| * @author MCD Application Team |
| * @brief Header file of ADC HAL extension module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2016 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef __STM32F2xx_ADC_EX_H |
| #define __STM32F2xx_ADC_EX_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f2xx_hal_def.h" |
| |
| /** @addtogroup STM32F2xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup ADCEx |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup ADCEx_Exported_Types ADC Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief ADC Configuration injected Channel structure definition |
| * @note Parameters of this structure are shared within 2 scopes: |
| * - Scope channel: InjectedChannel, InjectedRank, InjectedSamplingTime, InjectedOffset |
| * - Scope injected group (affects all channels of injected group): InjectedNbrOfConversion, InjectedDiscontinuousConvMode, |
| * AutoInjectedConv, ExternalTrigInjecConvEdge, ExternalTrigInjecConv. |
| * @note The setting of these parameters with function HAL_ADCEx_InjectedConfigChannel() is conditioned to ADC state. |
| * ADC state can be either: |
| * - For all parameters: ADC disabled |
| * - For all except parameters 'InjectedDiscontinuousConvMode' and 'AutoInjectedConv': ADC enabled without conversion on going on injected group. |
| * - For parameters 'ExternalTrigInjecConv' and 'ExternalTrigInjecConvEdge': ADC enabled, even with conversion on going on injected group. |
| */ |
| typedef struct |
| { |
| uint32_t InjectedChannel; /*!< Selection of ADC channel to configure |
| This parameter can be a value of @ref ADC_channels |
| Note: Depending on devices, some channels may not be available on package pins. Refer to device datasheet for channels availability. */ |
| uint32_t InjectedRank; /*!< Rank in the injected group sequencer |
| This parameter must be a value of @ref ADCEx_injected_rank |
| Note: In case of need to disable a channel or change order of conversion sequencer, rank containing a previous channel setting can be overwritten by the new channel setting (or parameter number of conversions can be adjusted) */ |
| uint32_t InjectedSamplingTime; /*!< Sampling time value to be set for the selected channel. |
| Unit: ADC clock cycles |
| Conversion time is the addition of sampling time and processing time (12 ADC clock cycles at ADC resolution 12 bits, 11 cycles at 10 bits, 9 cycles at 8 bits, 7 cycles at 6 bits). |
| This parameter can be a value of @ref ADC_sampling_times |
| Caution: This parameter updates the parameter property of the channel, that can be used into regular and/or injected groups. |
| If this same channel has been previously configured in the other group (regular/injected), it will be updated to last setting. |
| Note: In case of usage of internal measurement channels (VrefInt/Vbat/TempSensor), |
| sampling time constraints must be respected (sampling time can be adjusted in function of ADC clock frequency and sampling time setting) |
| Refer to device datasheet for timings values, parameters TS_vrefint, TS_temp (values rough order: 4us min). */ |
| uint32_t InjectedOffset; /*!< Defines the offset to be subtracted from the raw converted data (for channels set on injected group only). |
| Offset value must be a positive number. |
| Depending of ADC resolution selected (12, 10, 8 or 6 bits), |
| this parameter must be a number between Min_Data = 0x000 and Max_Data = 0xFFF, 0x3FF, 0xFF or 0x3F respectively. */ |
| uint32_t InjectedNbrOfConversion; /*!< Specifies the number of ranks that will be converted within the injected group sequencer. |
| To use the injected group sequencer and convert several ranks, parameter 'ScanConvMode' must be enabled. |
| This parameter must be a number between Min_Data = 1 and Max_Data = 4. |
| Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to |
| configure a channel on injected group can impact the configuration of other channels previously set. */ |
| uint32_t InjectedDiscontinuousConvMode; /*!< Specifies whether the conversions sequence of injected group is performed in Complete-sequence/Discontinuous-sequence (main sequence subdivided in successive parts). |
| Discontinuous mode is used only if sequencer is enabled (parameter 'ScanConvMode'). If sequencer is disabled, this parameter is discarded. |
| Discontinuous mode can be enabled only if continuous mode is disabled. If continuous mode is enabled, this parameter setting is discarded. |
| This parameter can be set to ENABLE or DISABLE. |
| Note: For injected group, number of discontinuous ranks increment is fixed to one-by-one. |
| Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to |
| configure a channel on injected group can impact the configuration of other channels previously set. */ |
| uint32_t AutoInjectedConv; /*!< Enables or disables the selected ADC automatic injected group conversion after regular one |
| This parameter can be set to ENABLE or DISABLE. |
| Note: To use Automatic injected conversion, discontinuous mode must be disabled ('DiscontinuousConvMode' and 'InjectedDiscontinuousConvMode' set to DISABLE) |
| Note: To use Automatic injected conversion, injected group external triggers must be disabled ('ExternalTrigInjecConv' set to ADC_SOFTWARE_START) |
| Note: In case of DMA used with regular group: if DMA configured in normal mode (single shot) JAUTO will be stopped upon DMA transfer complete. |
| To maintain JAUTO always enabled, DMA must be configured in circular mode. |
| Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to |
| configure a channel on injected group can impact the configuration of other channels previously set. */ |
| uint32_t ExternalTrigInjecConv; /*!< Selects the external event used to trigger the conversion start of injected group. |
| If set to ADC_INJECTED_SOFTWARE_START, external triggers are disabled. |
| If set to external trigger source, triggering is on event rising edge. |
| This parameter can be a value of @ref ADCEx_External_trigger_Source_Injected |
| Note: This parameter must be modified when ADC is disabled (before ADC start conversion or after ADC stop conversion). |
| If ADC is enabled, this parameter setting is bypassed without error reporting (as it can be the expected behaviour in case of another parameter update on the fly) |
| Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to |
| configure a channel on injected group can impact the configuration of other channels previously set. */ |
| uint32_t ExternalTrigInjecConvEdge; /*!< Selects the external trigger edge of injected group. |
| This parameter can be a value of @ref ADCEx_External_trigger_edge_Injected. |
| If trigger is set to ADC_INJECTED_SOFTWARE_START, this parameter is discarded. |
| Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to |
| configure a channel on injected group can impact the configuration of other channels previously set. */ |
| }ADC_InjectionConfTypeDef; |
| |
| /** |
| * @brief ADC Configuration multi-mode structure definition |
| */ |
| typedef struct |
| { |
| uint32_t Mode; /*!< Configures the ADC to operate in independent or multi mode. |
| This parameter can be a value of @ref ADCEx_Common_mode */ |
| uint32_t DMAAccessMode; /*!< Configures the Direct memory access mode for multi ADC mode. |
| This parameter can be a value of @ref ADCEx_Direct_memory_access_mode_for_multi_mode */ |
| uint32_t TwoSamplingDelay; /*!< Configures the Delay between 2 sampling phases. |
| This parameter can be a value of @ref ADC_delay_between_2_sampling_phases */ |
| }ADC_MultiModeTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup ADCEx_Exported_Constants ADC Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup ADCEx_Common_mode ADC Common Mode |
| * @{ |
| */ |
| #define ADC_MODE_INDEPENDENT 0x00000000U |
| #define ADC_DUALMODE_REGSIMULT_INJECSIMULT ((uint32_t)ADC_CCR_MULTI_0) |
| #define ADC_DUALMODE_REGSIMULT_ALTERTRIG ((uint32_t)ADC_CCR_MULTI_1) |
| #define ADC_DUALMODE_INJECSIMULT ((uint32_t)(ADC_CCR_MULTI_2 | ADC_CCR_MULTI_0)) |
| #define ADC_DUALMODE_REGSIMULT ((uint32_t)(ADC_CCR_MULTI_2 | ADC_CCR_MULTI_1)) |
| #define ADC_DUALMODE_INTERL ((uint32_t)(ADC_CCR_MULTI_2 | ADC_CCR_MULTI_1 | ADC_CCR_MULTI_0)) |
| #define ADC_DUALMODE_ALTERTRIG ((uint32_t)(ADC_CCR_MULTI_3 | ADC_CCR_MULTI_0)) |
| #define ADC_TRIPLEMODE_REGSIMULT_INJECSIMULT ((uint32_t)(ADC_CCR_MULTI_4 | ADC_CCR_MULTI_0)) |
| #define ADC_TRIPLEMODE_REGSIMULT_AlterTrig ((uint32_t)(ADC_CCR_MULTI_4 | ADC_CCR_MULTI_1)) |
| #define ADC_TRIPLEMODE_INJECSIMULT ((uint32_t)(ADC_CCR_MULTI_4 | ADC_CCR_MULTI_2 | ADC_CCR_MULTI_0)) |
| #define ADC_TRIPLEMODE_REGSIMULT ((uint32_t)(ADC_CCR_MULTI_4 | ADC_CCR_MULTI_2 | ADC_CCR_MULTI_1)) |
| #define ADC_TRIPLEMODE_INTERL ((uint32_t)(ADC_CCR_MULTI_4 | ADC_CCR_MULTI_2 | ADC_CCR_MULTI_1 | ADC_CCR_MULTI_0)) |
| #define ADC_TRIPLEMODE_ALTERTRIG ((uint32_t)(ADC_CCR_MULTI_4 | ADC_CCR_MULTI_3 | ADC_CCR_MULTI_0)) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADCEx_Direct_memory_access_mode_for_multi_mode ADC Direct Memory Access Mode For Multi Mode |
| * @{ |
| */ |
| #define ADC_DMAACCESSMODE_DISABLED 0x00000000U /*!< DMA mode disabled */ |
| #define ADC_DMAACCESSMODE_1 ((uint32_t)ADC_CCR_DMA_0) /*!< DMA mode 1 enabled (2 / 3 half-words one by one - 1 then 2 then 3)*/ |
| #define ADC_DMAACCESSMODE_2 ((uint32_t)ADC_CCR_DMA_1) /*!< DMA mode 2 enabled (2 / 3 half-words by pairs - 2&1 then 1&3 then 3&2)*/ |
| #define ADC_DMAACCESSMODE_3 ((uint32_t)ADC_CCR_DMA) /*!< DMA mode 3 enabled (2 / 3 bytes by pairs - 2&1 then 1&3 then 3&2) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADCEx_External_trigger_edge_Injected ADC External Trigger Edge Injected |
| * @{ |
| */ |
| #define ADC_EXTERNALTRIGINJECCONVEDGE_NONE 0x00000000U |
| #define ADC_EXTERNALTRIGINJECCONVEDGE_RISING ((uint32_t)ADC_CR2_JEXTEN_0) |
| #define ADC_EXTERNALTRIGINJECCONVEDGE_FALLING ((uint32_t)ADC_CR2_JEXTEN_1) |
| #define ADC_EXTERNALTRIGINJECCONVEDGE_RISINGFALLING ((uint32_t)ADC_CR2_JEXTEN) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADCEx_External_trigger_Source_Injected ADC External Trigger Source Injected |
| * @{ |
| */ |
| #define ADC_EXTERNALTRIGINJECCONV_T1_CC4 0x00000000U |
| #define ADC_EXTERNALTRIGINJECCONV_T1_TRGO ((uint32_t)ADC_CR2_JEXTSEL_0) |
| #define ADC_EXTERNALTRIGINJECCONV_T2_CC1 ((uint32_t)ADC_CR2_JEXTSEL_1) |
| #define ADC_EXTERNALTRIGINJECCONV_T2_TRGO ((uint32_t)(ADC_CR2_JEXTSEL_1 | ADC_CR2_JEXTSEL_0)) |
| #define ADC_EXTERNALTRIGINJECCONV_T3_CC2 ((uint32_t)ADC_CR2_JEXTSEL_2) |
| #define ADC_EXTERNALTRIGINJECCONV_T3_CC4 ((uint32_t)(ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_0)) |
| #define ADC_EXTERNALTRIGINJECCONV_T4_CC1 ((uint32_t)(ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_1)) |
| #define ADC_EXTERNALTRIGINJECCONV_T4_CC2 ((uint32_t)(ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_1 | ADC_CR2_JEXTSEL_0)) |
| #define ADC_EXTERNALTRIGINJECCONV_T4_CC3 ((uint32_t)ADC_CR2_JEXTSEL_3) |
| #define ADC_EXTERNALTRIGINJECCONV_T4_TRGO ((uint32_t)(ADC_CR2_JEXTSEL_3 | ADC_CR2_JEXTSEL_0)) |
| #define ADC_EXTERNALTRIGINJECCONV_T5_CC4 ((uint32_t)(ADC_CR2_JEXTSEL_3 | ADC_CR2_JEXTSEL_1)) |
| #define ADC_EXTERNALTRIGINJECCONV_T5_TRGO ((uint32_t)(ADC_CR2_JEXTSEL_3 | ADC_CR2_JEXTSEL_1 | ADC_CR2_JEXTSEL_0)) |
| #define ADC_EXTERNALTRIGINJECCONV_T8_CC2 ((uint32_t)(ADC_CR2_JEXTSEL_3 | ADC_CR2_JEXTSEL_2)) |
| #define ADC_EXTERNALTRIGINJECCONV_T8_CC3 ((uint32_t)(ADC_CR2_JEXTSEL_3 | ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_0)) |
| #define ADC_EXTERNALTRIGINJECCONV_T8_CC4 ((uint32_t)(ADC_CR2_JEXTSEL_3 | ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_1)) |
| #define ADC_EXTERNALTRIGINJECCONV_EXT_IT15 ((uint32_t)ADC_CR2_JEXTSEL) |
| #define ADC_INJECTED_SOFTWARE_START ((uint32_t)ADC_CR2_JEXTSEL + 1U) |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADCEx_injected_rank ADC Injected Rank |
| * @{ |
| */ |
| #define ADC_INJECTED_RANK_1 0x00000001U |
| #define ADC_INJECTED_RANK_2 0x00000002U |
| #define ADC_INJECTED_RANK_3 0x00000003U |
| #define ADC_INJECTED_RANK_4 0x00000004U |
| /** |
| * @} |
| */ |
| |
| /** @defgroup ADCEx_channels ADC Specific Channels |
| * @{ |
| */ |
| #define ADC_CHANNEL_TEMPSENSOR ((uint32_t)ADC_CHANNEL_16) |
| /** |
| * @} |
| */ |
| |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| /** @defgroup ADC_Exported_Macros ADC Exported Macros |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup ADCEx_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup ADCEx_Exported_Functions_Group1 |
| * @{ |
| */ |
| |
| /* I/O operation functions ******************************************************/ |
| HAL_StatusTypeDef HAL_ADCEx_InjectedStart(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADCEx_InjectedStop(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADCEx_InjectedPollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_ADCEx_InjectedStart_IT(ADC_HandleTypeDef* hadc); |
| HAL_StatusTypeDef HAL_ADCEx_InjectedStop_IT(ADC_HandleTypeDef* hadc); |
| uint32_t HAL_ADCEx_InjectedGetValue(ADC_HandleTypeDef* hadc, uint32_t InjectedRank); |
| HAL_StatusTypeDef HAL_ADCEx_MultiModeStart_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length); |
| HAL_StatusTypeDef HAL_ADCEx_MultiModeStop_DMA(ADC_HandleTypeDef* hadc); |
| uint32_t HAL_ADCEx_MultiModeGetValue(ADC_HandleTypeDef* hadc); |
| void HAL_ADCEx_InjectedConvCpltCallback(ADC_HandleTypeDef* hadc); |
| |
| /* Peripheral Control functions *************************************************/ |
| HAL_StatusTypeDef HAL_ADCEx_InjectedConfigChannel(ADC_HandleTypeDef* hadc,ADC_InjectionConfTypeDef* sConfigInjected); |
| HAL_StatusTypeDef HAL_ADCEx_MultiModeConfigChannel(ADC_HandleTypeDef* hadc, ADC_MultiModeTypeDef* multimode); |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| /* Private types -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup ADCEx_Private_Constants ADC Private Constants |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup ADCEx_Private_Macros ADC Private Macros |
| * @{ |
| */ |
| #define IS_ADC_CHANNEL(CHANNEL) ((CHANNEL) <= ADC_CHANNEL_18) |
| |
| #define IS_ADC_MODE(MODE) (((MODE) == ADC_MODE_INDEPENDENT) || \ |
| ((MODE) == ADC_DUALMODE_REGSIMULT_INJECSIMULT) || \ |
| ((MODE) == ADC_DUALMODE_REGSIMULT_ALTERTRIG) || \ |
| ((MODE) == ADC_DUALMODE_INJECSIMULT) || \ |
| ((MODE) == ADC_DUALMODE_REGSIMULT) || \ |
| ((MODE) == ADC_DUALMODE_INTERL) || \ |
| ((MODE) == ADC_DUALMODE_ALTERTRIG) || \ |
| ((MODE) == ADC_TRIPLEMODE_REGSIMULT_INJECSIMULT) || \ |
| ((MODE) == ADC_TRIPLEMODE_REGSIMULT_AlterTrig) || \ |
| ((MODE) == ADC_TRIPLEMODE_INJECSIMULT) || \ |
| ((MODE) == ADC_TRIPLEMODE_REGSIMULT) || \ |
| ((MODE) == ADC_TRIPLEMODE_INTERL) || \ |
| ((MODE) == ADC_TRIPLEMODE_ALTERTRIG)) |
| #define IS_ADC_DMA_ACCESS_MODE(MODE) (((MODE) == ADC_DMAACCESSMODE_DISABLED) || \ |
| ((MODE) == ADC_DMAACCESSMODE_1) || \ |
| ((MODE) == ADC_DMAACCESSMODE_2) || \ |
| ((MODE) == ADC_DMAACCESSMODE_3)) |
| #define IS_ADC_EXT_INJEC_TRIG_EDGE(EDGE) (((EDGE) == ADC_EXTERNALTRIGINJECCONVEDGE_NONE) || \ |
| ((EDGE) == ADC_EXTERNALTRIGINJECCONVEDGE_RISING) || \ |
| ((EDGE) == ADC_EXTERNALTRIGINJECCONVEDGE_FALLING) || \ |
| ((EDGE) == ADC_EXTERNALTRIGINJECCONVEDGE_RISINGFALLING)) |
| #define IS_ADC_EXT_INJEC_TRIG(INJTRIG) (((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_CC4) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_TRGO) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_CC1) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_TRGO) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T3_CC2) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T3_CC4) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_CC1) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_CC2) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_CC3) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_TRGO) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T5_CC4) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T5_TRGO) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T8_CC2) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T8_CC3) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_T8_CC4) || \ |
| ((INJTRIG) == ADC_EXTERNALTRIGINJECCONV_EXT_IT15)|| \ |
| ((INJTRIG) == ADC_INJECTED_SOFTWARE_START)) |
| #define IS_ADC_INJECTED_LENGTH(LENGTH) (((LENGTH) >= ((uint32_t)1U)) && ((LENGTH) <= ((uint32_t)4U))) |
| #define IS_ADC_INJECTED_RANK(RANK) (((RANK) >= ((uint32_t)1U)) && ((RANK) <= ((uint32_t)4U))) |
| |
| /** |
| * @brief Set the selected injected Channel rank. |
| * @param _CHANNELNB_ Channel number. |
| * @param _RANKNB_ Rank number. |
| * @param _JSQR_JL_ Sequence length. |
| * @retval None |
| */ |
| #define ADC_JSQR(_CHANNELNB_, _RANKNB_, _JSQR_JL_) (((uint32_t)((uint16_t)(_CHANNELNB_))) << (5U * (uint8_t)(((_RANKNB_) + 3U) - (_JSQR_JL_)))) |
| |
| /** |
| * @} |
| */ |
| |
| /* Private functions ---------------------------------------------------------*/ |
| /** @defgroup ADCEx_Private_Functions ADC Private Functions |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /*__STM32F2xx_ADC_EX_H */ |
| |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |