| /** |
| ****************************************************************************** |
| * @file stm32f4xx_hal_rtc.c |
| * @author MCD Application Team |
| * @brief RTC HAL module driver. |
| * This file provides firmware functions to manage the following |
| * functionalities of the Real Time Clock (RTC) peripheral: |
| * + Initialization and de-initialization functions |
| * + RTC Time and Date functions |
| * + RTC Alarm functions |
| * + Peripheral Control functions |
| * + Peripheral State functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Backup Domain Operating Condition ##### |
| ============================================================================== |
| [..] The real-time clock (RTC), the RTC backup registers, and the backup |
| SRAM (BKP SRAM) can be powered from the VBAT voltage when the main |
| VDD supply is powered off. |
| To retain the content of the RTC backup registers, backup SRAM, and supply |
| the RTC when VDD is turned off, VBAT pin can be connected to an optional |
| standby voltage supplied by a battery or by another source. |
| |
| [..] To allow the RTC operating even when the main digital supply (VDD) is turned |
| off, the VBAT pin powers the following blocks: |
| (#) The RTC |
| (#) The LSE oscillator |
| (#) The backup SRAM when the low power backup regulator is enabled |
| (#) PC13 to PC15 I/Os, plus PI8 I/O (when available) |
| |
| [..] When the backup domain is supplied by VDD (analog switch connected to VDD), |
| the following pins are available: |
| (#) PC14 and PC15 can be used as either GPIO or LSE pins |
| (#) PC13 can be used as a GPIO or as the RTC_AF1 pin |
| (#) PI8 can be used as a GPIO or as the RTC_AF2 pin |
| |
| [..] When the backup domain is supplied by VBAT (analog switch connected to VBAT |
| because VDD is not present), the following pins are available: |
| (#) PC14 and PC15 can be used as LSE pins only |
| (#) PC13 can be used as the RTC_AF1 pin |
| (#) PI8 can be used as the RTC_AF2 pin |
| |
| ##### Backup Domain Reset ##### |
| ================================================================== |
| [..] The backup domain reset sets all RTC registers and the RCC_BDCR register |
| to their reset values. The BKPSRAM is not affected by this reset. The only |
| way to reset the BKPSRAM is through the Flash interface by requesting |
| a protection level change from 1 to 0. |
| [..] A backup domain reset is generated when one of the following events occurs: |
| (#) Software reset, triggered by setting the BDRST bit in the |
| RCC Backup domain control register (RCC_BDCR). |
| (#) VDD or VBAT power on, if both supplies have previously been powered off. |
| |
| ##### Backup Domain Access ##### |
| ================================================================== |
| [..] After reset, the backup domain (RTC registers, RTC backup data |
| registers and backup SRAM) is protected against possible unwanted write |
| accesses. |
| [..] To enable access to the RTC Domain and RTC registers, proceed as follows: |
| (+) Enable the Power Controller (PWR) APB1 interface clock using the |
| __HAL_RCC_PWR_CLK_ENABLE() function. |
| (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. |
| (+) Select the RTC clock source using the __HAL_RCC_RTC_CONFIG() function. |
| (+) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() function. |
| |
| |
| ##### How to use this driver ##### |
| ================================================================== |
| [..] |
| (+) Enable the RTC domain access (see description in the section above). |
| (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour |
| format using the HAL_RTC_Init() function. |
| |
| *** Time and Date configuration *** |
| =================================== |
| [..] |
| (+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime() |
| and HAL_RTC_SetDate() functions. |
| (+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions. |
| |
| *** Alarm configuration *** |
| =========================== |
| [..] |
| (+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function. |
| You can also configure the RTC Alarm with interrupt mode using the HAL_RTC_SetAlarm_IT() function. |
| (+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function. |
| |
| ##### RTC and low power modes ##### |
| ================================================================== |
| [..] The MCU can be woken up from a low power mode by an RTC alternate |
| function. |
| [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B), |
| RTC wake-up, RTC tamper event detection and RTC time stamp event detection. |
| These RTC alternate functions can wake up the system from the Stop and |
| Standby low power modes. |
| [..] The system can also wake up from low power modes without depending |
| on an external interrupt (Auto-wake-up mode), by using the RTC alarm |
| or the RTC wake-up events. |
| [..] The RTC provides a programmable time base for waking up from the |
| Stop or Standby mode at regular intervals. |
| Wake-up from STOP and STANDBY modes is possible only when the RTC clock source |
| is LSE or LSI. |
| |
| *** Callback registration *** |
| ============================================= |
| |
| [..] |
| The compilation define USE_HAL_RTC_REGISTER_CALLBACKS when set to 1 |
| allows the user to configure dynamically the driver callbacks. |
| Use Function HAL_RTC_RegisterCallback() to register an interrupt callback. |
| |
| [..] |
| Function HAL_RTC_RegisterCallback() allows to register following callbacks: |
| (+) AlarmAEventCallback : RTC Alarm A Event callback. |
| (+) AlarmBEventCallback : RTC Alarm B Event callback. |
| (+) TimeStampEventCallback : RTC TimeStamp Event callback. |
| (+) WakeUpTimerEventCallback : RTC WakeUpTimer Event callback. |
| (+) Tamper1EventCallback : RTC Tamper 1 Event callback. |
| (+) Tamper2EventCallback : RTC Tamper 2 Event callback. |
| (+) MspInitCallback : RTC MspInit callback. |
| (+) MspDeInitCallback : RTC MspDeInit callback. |
| [..] |
| This function takes as parameters the HAL peripheral handle, the Callback ID |
| and a pointer to the user callback function. |
| |
| [..] |
| Use function HAL_RTC_UnRegisterCallback() to reset a callback to the default |
| weak function. |
| HAL_RTC_UnRegisterCallback() takes as parameters the HAL peripheral handle, |
| and the Callback ID. |
| This function allows to reset following callbacks: |
| (+) AlarmAEventCallback : RTC Alarm A Event callback. |
| (+) AlarmBEventCallback : RTC Alarm B Event callback. |
| (+) TimeStampEventCallback : RTC TimeStamp Event callback. |
| (+) WakeUpTimerEventCallback : RTC WakeUpTimer Event callback. |
| (+) Tamper1EventCallback : RTC Tamper 1 Event callback. |
| (+) Tamper2EventCallback : RTC Tamper 2 Event callback. |
| (+) MspInitCallback : RTC MspInit callback. |
| (+) MspDeInitCallback : RTC MspDeInit callback. |
| |
| [..] |
| By default, after the HAL_RTC_Init() and when the state is HAL_RTC_STATE_RESET, |
| all callbacks are set to the corresponding weak functions : |
| examples AlarmAEventCallback(), WakeUpTimerEventCallback(). |
| Exception done for MspInit and MspDeInit callbacks that are reset to the legacy weak function |
| in the HAL_RTC_Init()/HAL_RTC_DeInit() only when these callbacks are null |
| (not registered beforehand). |
| If not, MspInit or MspDeInit are not null, HAL_RTC_Init()/HAL_RTC_DeInit() |
| keep and use the user MspInit/MspDeInit callbacks (registered beforehand) |
| |
| [..] |
| Callbacks can be registered/unregistered in HAL_RTC_STATE_READY state only. |
| Exception done MspInit/MspDeInit that can be registered/unregistered |
| in HAL_RTC_STATE_READY or HAL_RTC_STATE_RESET state, |
| thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit. |
| In that case first register the MspInit/MspDeInit user callbacks |
| using HAL_RTC_RegisterCallback() before calling HAL_RTC_DeInit() |
| or HAL_RTC_Init() function. |
| |
| [..] |
| When The compilation define USE_HAL_RTC_REGISTER_CALLBACKS is set to 0 or |
| not defined, the callback registration feature is not available and all callbacks |
| are set to the corresponding weak functions. |
| @endverbatim |
| |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f4xx_hal.h" |
| |
| /** @addtogroup STM32F4xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup RTC RTC |
| * @brief RTC HAL module driver |
| * @{ |
| */ |
| |
| #ifdef HAL_RTC_MODULE_ENABLED |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /* Private macro -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Exported functions --------------------------------------------------------*/ |
| |
| /** @defgroup RTC_Exported_Functions RTC Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup RTC_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Initialization and de-initialization functions ##### |
| =============================================================================== |
| [..] This section provides functions allowing to initialize and configure the |
| RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable |
| RTC registers Write protection, enter and exit the RTC initialization mode, |
| RTC registers synchronization check and reference clock detection enable. |
| (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base. |
| It is split into 2 programmable prescalers to minimize power consumption. |
| (++) A 7-bit asynchronous prescaler and a 13-bit synchronous prescaler. |
| (++) When both prescalers are used, it is recommended to configure the |
| asynchronous prescaler to a high value to minimize power consumption. |
| (#) All RTC registers are Write protected. Writing to the RTC registers |
| is enabled by writing a key into the Write Protection register, RTC_WPR. |
| (#) To configure the RTC Calendar, user application should enter |
| initialization mode. In this mode, the calendar counter is stopped |
| and its value can be updated. When the initialization sequence is |
| complete, the calendar restarts counting after 4 RTCCLK cycles. |
| (#) To read the calendar through the shadow registers after Calendar |
| initialization, calendar update or after wake-up from low power modes |
| the software must first clear the RSF flag. The software must then |
| wait until it is set again before reading the calendar, which means |
| that the calendar registers have been correctly copied into the |
| RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function |
| implements the above software sequence (RSF clear and RSF check). |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the RTC peripheral |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc) |
| { |
| /* Check the RTC peripheral state */ |
| if(hrtc == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat)); |
| assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv)); |
| assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv)); |
| assert_param (IS_RTC_OUTPUT(hrtc->Init.OutPut)); |
| assert_param (IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity)); |
| assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType)); |
| |
| #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) |
| if(hrtc->State == HAL_RTC_STATE_RESET) |
| { |
| /* Allocate lock resource and initialize it */ |
| hrtc->Lock = HAL_UNLOCKED; |
| |
| hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback; /* Legacy weak AlarmAEventCallback */ |
| hrtc->AlarmBEventCallback = HAL_RTCEx_AlarmBEventCallback; /* Legacy weak AlarmBEventCallback */ |
| hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback; /* Legacy weak TimeStampEventCallback */ |
| hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */ |
| hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback; /* Legacy weak Tamper1EventCallback */ |
| hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback; /* Legacy weak Tamper2EventCallback */ |
| |
| if(hrtc->MspInitCallback == NULL) |
| { |
| hrtc->MspInitCallback = HAL_RTC_MspInit; |
| } |
| /* Init the low level hardware */ |
| hrtc->MspInitCallback(hrtc); |
| |
| if(hrtc->MspDeInitCallback == NULL) |
| { |
| hrtc->MspDeInitCallback = HAL_RTC_MspDeInit; |
| } |
| } |
| #else |
| if(hrtc->State == HAL_RTC_STATE_RESET) |
| { |
| /* Allocate lock resource and initialize it */ |
| hrtc->Lock = HAL_UNLOCKED; |
| |
| /* Initialize RTC MSP */ |
| HAL_RTC_MspInit(hrtc); |
| } |
| #endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */ |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| /* Set Initialization mode */ |
| if(RTC_EnterInitMode(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Clear RTC_CR FMT, OSEL and POL Bits */ |
| hrtc->Instance->CR &= ((uint32_t)~(RTC_CR_FMT | RTC_CR_OSEL | RTC_CR_POL)); |
| /* Set RTC_CR register */ |
| hrtc->Instance->CR |= (uint32_t)(hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity); |
| |
| /* Configure the RTC PRER */ |
| hrtc->Instance->PRER = (uint32_t)(hrtc->Init.SynchPrediv); |
| hrtc->Instance->PRER |= (uint32_t)(hrtc->Init.AsynchPrediv << 16U); |
| |
| /* Exit Initialization mode */ |
| hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; |
| |
| /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ |
| if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) |
| { |
| if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| return HAL_ERROR; |
| } |
| } |
| |
| hrtc->Instance->TAFCR &= (uint32_t)~RTC_TAFCR_ALARMOUTTYPE; |
| hrtc->Instance->TAFCR |= (uint32_t)(hrtc->Init.OutPutType); |
| |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_READY; |
| |
| return HAL_OK; |
| } |
| } |
| |
| /** |
| * @brief DeInitializes the RTC peripheral |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @note This function doesn't reset the RTC Backup Data registers. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc) |
| { |
| uint32_t tickstart = 0U; |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| /* Set Initialization mode */ |
| if(RTC_EnterInitMode(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Reset TR, DR and CR registers */ |
| hrtc->Instance->TR = 0x00000000U; |
| hrtc->Instance->DR = 0x00002101U; |
| /* Reset All CR bits except CR[2:0] */ |
| hrtc->Instance->CR &= 0x00000007U; |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till WUTWF flag is set and if Time out is reached exit */ |
| while(((hrtc->Instance->ISR) & RTC_ISR_WUTWF) == (uint32_t)RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Reset all RTC CR register bits */ |
| hrtc->Instance->CR &= 0x00000000U; |
| hrtc->Instance->WUTR = 0x0000FFFFU; |
| hrtc->Instance->PRER = 0x007F00FFU; |
| hrtc->Instance->CALIBR = 0x00000000U; |
| hrtc->Instance->ALRMAR = 0x00000000U; |
| hrtc->Instance->ALRMBR = 0x00000000U; |
| hrtc->Instance->SHIFTR = 0x00000000U; |
| hrtc->Instance->CALR = 0x00000000U; |
| hrtc->Instance->ALRMASSR = 0x00000000U; |
| hrtc->Instance->ALRMBSSR = 0x00000000U; |
| |
| /* Reset ISR register and exit initialization mode */ |
| hrtc->Instance->ISR = 0x00000000U; |
| |
| /* Reset Tamper and alternate functions configuration register */ |
| hrtc->Instance->TAFCR = 0x00000000U; |
| |
| /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ |
| if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) |
| { |
| if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| return HAL_ERROR; |
| } |
| } |
| } |
| |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) |
| if(hrtc->MspDeInitCallback == NULL) |
| { |
| hrtc->MspDeInitCallback = HAL_RTC_MspDeInit; |
| } |
| |
| /* DeInit the low level hardware: CLOCK, NVIC.*/ |
| hrtc->MspDeInitCallback(hrtc); |
| |
| #else |
| /* De-Initialize RTC MSP */ |
| HAL_RTC_MspDeInit(hrtc); |
| #endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */ |
| |
| hrtc->State = HAL_RTC_STATE_RESET; |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_OK; |
| } |
| |
| #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) |
| /** |
| * @brief Register a User RTC Callback |
| * To be used instead of the weak predefined callback |
| * @param hrtc RTC handle |
| * @param CallbackID ID of the callback to be registered |
| * This parameter can be one of the following values: |
| * @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID Alarm A Event Callback ID |
| * @arg @ref HAL_RTC_ALARM_B_EVENT_CB_ID Alarm B Event Callback ID |
| * @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID TimeStamp Event Callback ID |
| * @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID Wake-Up Timer Event Callback ID |
| * @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID Tamper 1 Callback ID |
| * @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID Tamper 2 Callback ID |
| * @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID |
| * @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID |
| * @param pCallback pointer to the Callback function |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_RegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID, pRTC_CallbackTypeDef pCallback) |
| { |
| HAL_StatusTypeDef status = HAL_OK; |
| |
| if(pCallback == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Process locked */ |
| __HAL_LOCK(hrtc); |
| |
| if(HAL_RTC_STATE_READY == hrtc->State) |
| { |
| switch (CallbackID) |
| { |
| case HAL_RTC_ALARM_A_EVENT_CB_ID : |
| hrtc->AlarmAEventCallback = pCallback; |
| break; |
| |
| case HAL_RTC_ALARM_B_EVENT_CB_ID : |
| hrtc->AlarmBEventCallback = pCallback; |
| break; |
| |
| case HAL_RTC_TIMESTAMP_EVENT_CB_ID : |
| hrtc->TimeStampEventCallback = pCallback; |
| break; |
| |
| case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID : |
| hrtc->WakeUpTimerEventCallback = pCallback; |
| break; |
| |
| case HAL_RTC_TAMPER1_EVENT_CB_ID : |
| hrtc->Tamper1EventCallback = pCallback; |
| break; |
| |
| case HAL_RTC_TAMPER2_EVENT_CB_ID : |
| hrtc->Tamper2EventCallback = pCallback; |
| break; |
| |
| case HAL_RTC_MSPINIT_CB_ID : |
| hrtc->MspInitCallback = pCallback; |
| break; |
| |
| case HAL_RTC_MSPDEINIT_CB_ID : |
| hrtc->MspDeInitCallback = pCallback; |
| break; |
| |
| default : |
| /* Return error status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else if(HAL_RTC_STATE_RESET == hrtc->State) |
| { |
| switch (CallbackID) |
| { |
| case HAL_RTC_MSPINIT_CB_ID : |
| hrtc->MspInitCallback = pCallback; |
| break; |
| |
| case HAL_RTC_MSPDEINIT_CB_ID : |
| hrtc->MspDeInitCallback = pCallback; |
| break; |
| |
| default : |
| /* Return error status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else |
| { |
| /* Return error status */ |
| status = HAL_ERROR; |
| } |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hrtc); |
| |
| return status; |
| } |
| |
| /** |
| * @brief Unregister an RTC Callback |
| * RTC callabck is redirected to the weak predefined callback |
| * @param hrtc RTC handle |
| * @param CallbackID ID of the callback to be unregistered |
| * This parameter can be one of the following values: |
| * @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID Alarm A Event Callback ID |
| * @arg @ref HAL_RTC_ALARM_B_EVENT_CB_ID Alarm B Event Callback ID |
| * @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID TimeStamp Event Callback ID |
| * @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID Wake-Up Timer Event Callback ID |
| * @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID Tamper 1 Callback ID |
| * @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID Tamper 2 Callback ID |
| * @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID |
| * @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_UnRegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID) |
| { |
| HAL_StatusTypeDef status = HAL_OK; |
| |
| /* Process locked */ |
| __HAL_LOCK(hrtc); |
| |
| if(HAL_RTC_STATE_READY == hrtc->State) |
| { |
| switch (CallbackID) |
| { |
| case HAL_RTC_ALARM_A_EVENT_CB_ID : |
| hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback; /* Legacy weak AlarmAEventCallback */ |
| break; |
| |
| case HAL_RTC_ALARM_B_EVENT_CB_ID : |
| hrtc->AlarmBEventCallback = HAL_RTCEx_AlarmBEventCallback; /* Legacy weak AlarmBEventCallback */ |
| break; |
| |
| case HAL_RTC_TIMESTAMP_EVENT_CB_ID : |
| hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback; /* Legacy weak TimeStampEventCallback */ |
| break; |
| |
| case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID : |
| hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */ |
| break; |
| |
| case HAL_RTC_TAMPER1_EVENT_CB_ID : |
| hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback; /* Legacy weak Tamper1EventCallback */ |
| break; |
| |
| case HAL_RTC_TAMPER2_EVENT_CB_ID : |
| hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback; /* Legacy weak Tamper2EventCallback */ |
| break; |
| |
| case HAL_RTC_MSPINIT_CB_ID : |
| hrtc->MspInitCallback = HAL_RTC_MspInit; |
| break; |
| |
| case HAL_RTC_MSPDEINIT_CB_ID : |
| hrtc->MspDeInitCallback = HAL_RTC_MspDeInit; |
| break; |
| |
| default : |
| /* Return error status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else if(HAL_RTC_STATE_RESET == hrtc->State) |
| { |
| switch (CallbackID) |
| { |
| case HAL_RTC_MSPINIT_CB_ID : |
| hrtc->MspInitCallback = HAL_RTC_MspInit; |
| break; |
| |
| case HAL_RTC_MSPDEINIT_CB_ID : |
| hrtc->MspDeInitCallback = HAL_RTC_MspDeInit; |
| break; |
| |
| default : |
| /* Return error status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else |
| { |
| /* Return error status */ |
| status = HAL_ERROR; |
| } |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hrtc); |
| |
| return status; |
| } |
| #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ |
| |
| /** |
| * @brief Initializes the RTC MSP. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval None |
| */ |
| __weak void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hrtc); |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_RTC_MspInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief DeInitializes the RTC MSP. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval None |
| */ |
| __weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hrtc); |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_RTC_MspDeInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTC_Exported_Functions_Group2 RTC Time and Date functions |
| * @brief RTC Time and Date functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### RTC Time and Date functions ##### |
| =============================================================================== |
| |
| [..] This section provides functions allowing to configure Time and Date features |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Sets RTC current time. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sTime Pointer to Time structure |
| * @param Format Specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format) |
| { |
| uint32_t tmpreg = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving)); |
| assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation)); |
| |
| /* Process Locked */ |
| __HAL_LOCK(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| if(Format == RTC_FORMAT_BIN) |
| { |
| if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) |
| { |
| assert_param(IS_RTC_HOUR12(sTime->Hours)); |
| assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat)); |
| } |
| else |
| { |
| sTime->TimeFormat = 0x00U; |
| assert_param(IS_RTC_HOUR24(sTime->Hours)); |
| } |
| assert_param(IS_RTC_MINUTES(sTime->Minutes)); |
| assert_param(IS_RTC_SECONDS(sTime->Seconds)); |
| |
| tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(sTime->Hours) << 16U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sTime->Minutes) << 8U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sTime->Seconds)) | \ |
| (((uint32_t)sTime->TimeFormat) << 16U)); |
| } |
| else |
| { |
| if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) |
| { |
| assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sTime->Hours))); |
| assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat)); |
| } |
| else |
| { |
| sTime->TimeFormat = 0x00U; |
| assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours))); |
| } |
| assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes))); |
| assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds))); |
| tmpreg = (((uint32_t)(sTime->Hours) << 16U) | \ |
| ((uint32_t)(sTime->Minutes) << 8U) | \ |
| ((uint32_t)sTime->Seconds) | \ |
| ((uint32_t)(sTime->TimeFormat) << 16U)); |
| } |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| /* Set Initialization mode */ |
| if(RTC_EnterInitMode(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Set RTC state */ |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Set the RTC_TR register */ |
| hrtc->Instance->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK); |
| |
| /* This interface is deprecated. To manage Daylight Saving Time, please use HAL_RTC_DST_xxx functions */ |
| hrtc->Instance->CR &= (uint32_t)~RTC_CR_BCK; |
| |
| /* This interface is deprecated. To manage Daylight Saving Time, please use HAL_RTC_DST_xxx functions */ |
| hrtc->Instance->CR |= (uint32_t)(sTime->DayLightSaving | sTime->StoreOperation); |
| |
| /* Exit Initialization mode */ |
| hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; |
| |
| /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ |
| if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) |
| { |
| if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_ERROR; |
| } |
| } |
| |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_READY; |
| |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_OK; |
| } |
| } |
| |
| /** |
| * @brief Gets RTC current time. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sTime Pointer to Time structure |
| * @param Format Specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @note You can use SubSeconds and SecondFraction (sTime structure fields returned) to convert SubSeconds |
| * value in second fraction ratio with time unit following generic formula: |
| * Second fraction ratio * time_unit= [(SecondFraction-SubSeconds)/(SecondFraction+1)] * time_unit |
| * This conversion can be performed only if no shift operation is pending (ie. SHFP=0) when PREDIV_S >= SS |
| * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values |
| * in the higher-order calendar shadow registers to ensure consistency between the time and date values. |
| * Reading RTC current time locks the values in calendar shadow registers until current date is read. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format) |
| { |
| uint32_t tmpreg = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| |
| /* Get subseconds structure field from the corresponding register */ |
| sTime->SubSeconds = (uint32_t)(hrtc->Instance->SSR); |
| |
| /* Get SecondFraction structure field from the corresponding register field*/ |
| sTime->SecondFraction = (uint32_t)(hrtc->Instance->PRER & RTC_PRER_PREDIV_S); |
| |
| /* Get the TR register */ |
| tmpreg = (uint32_t)(hrtc->Instance->TR & RTC_TR_RESERVED_MASK); |
| |
| /* Fill the structure fields with the read parameters */ |
| sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> 16U); |
| sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >> 8U); |
| sTime->Seconds = (uint8_t)(tmpreg & (RTC_TR_ST | RTC_TR_SU)); |
| sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> 16U); |
| |
| /* Check the input parameters format */ |
| if(Format == RTC_FORMAT_BIN) |
| { |
| /* Convert the time structure parameters to Binary format */ |
| sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours); |
| sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes); |
| sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Sets RTC current date. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sDate Pointer to date structure |
| * @param Format specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format) |
| { |
| uint32_t datetmpreg = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| |
| /* Process Locked */ |
| __HAL_LOCK(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| if((Format == RTC_FORMAT_BIN) && ((sDate->Month & 0x10U) == 0x10U)) |
| { |
| sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10U)) + (uint8_t)0x0AU); |
| } |
| |
| assert_param(IS_RTC_WEEKDAY(sDate->WeekDay)); |
| |
| if(Format == RTC_FORMAT_BIN) |
| { |
| assert_param(IS_RTC_YEAR(sDate->Year)); |
| assert_param(IS_RTC_MONTH(sDate->Month)); |
| assert_param(IS_RTC_DATE(sDate->Date)); |
| |
| datetmpreg = (((uint32_t)RTC_ByteToBcd2(sDate->Year) << 16U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sDate->Month) << 8U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sDate->Date)) | \ |
| ((uint32_t)sDate->WeekDay << 13U)); |
| } |
| else |
| { |
| assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(sDate->Year))); |
| assert_param(IS_RTC_MONTH(RTC_Bcd2ToByte(sDate->Month))); |
| assert_param(IS_RTC_DATE(RTC_Bcd2ToByte(sDate->Date))); |
| |
| datetmpreg = ((((uint32_t)sDate->Year) << 16U) | \ |
| (((uint32_t)sDate->Month) << 8U) | \ |
| ((uint32_t)sDate->Date) | \ |
| (((uint32_t)sDate->WeekDay) << 13U)); |
| } |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| /* Set Initialization mode */ |
| if(RTC_EnterInitMode(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Set RTC state*/ |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Set the RTC_DR register */ |
| hrtc->Instance->DR = (uint32_t)(datetmpreg & RTC_DR_RESERVED_MASK); |
| |
| /* Exit Initialization mode */ |
| hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; |
| |
| /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ |
| if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) |
| { |
| if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_ERROR; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_ERROR; |
| } |
| } |
| |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_READY ; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_OK; |
| } |
| } |
| |
| /** |
| * @brief Gets RTC current date. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sDate Pointer to Date structure |
| * @param Format Specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values |
| * in the higher-order calendar shadow registers to ensure consistency between the time and date values. |
| * Reading RTC current time locks the values in calendar shadow registers until Current date is read. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format) |
| { |
| uint32_t datetmpreg = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| |
| /* Get the DR register */ |
| datetmpreg = (uint32_t)(hrtc->Instance->DR & RTC_DR_RESERVED_MASK); |
| |
| /* Fill the structure fields with the read parameters */ |
| sDate->Year = (uint8_t)((datetmpreg & (RTC_DR_YT | RTC_DR_YU)) >> 16U); |
| sDate->Month = (uint8_t)((datetmpreg & (RTC_DR_MT | RTC_DR_MU)) >> 8U); |
| sDate->Date = (uint8_t)(datetmpreg & (RTC_DR_DT | RTC_DR_DU)); |
| sDate->WeekDay = (uint8_t)((datetmpreg & (RTC_DR_WDU)) >> 13U); |
| |
| /* Check the input parameters format */ |
| if(Format == RTC_FORMAT_BIN) |
| { |
| /* Convert the date structure parameters to Binary format */ |
| sDate->Year = (uint8_t)RTC_Bcd2ToByte(sDate->Year); |
| sDate->Month = (uint8_t)RTC_Bcd2ToByte(sDate->Month); |
| sDate->Date = (uint8_t)RTC_Bcd2ToByte(sDate->Date); |
| } |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTC_Exported_Functions_Group3 RTC Alarm functions |
| * @brief RTC Alarm functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### RTC Alarm functions ##### |
| =============================================================================== |
| |
| [..] This section provides functions allowing to configure Alarm feature |
| |
| @endverbatim |
| * @{ |
| */ |
| /** |
| * @brief Sets the specified RTC Alarm. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sAlarm Pointer to Alarm structure |
| * @param Format Specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format) |
| { |
| uint32_t tickstart = 0U; |
| uint32_t tmpreg = 0U, subsecondtmpreg = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| assert_param(IS_RTC_ALARM(sAlarm->Alarm)); |
| assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask)); |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel)); |
| assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds)); |
| assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask)); |
| |
| /* Process Locked */ |
| __HAL_LOCK(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| if(Format == RTC_FORMAT_BIN) |
| { |
| if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) |
| { |
| assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours)); |
| assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); |
| } |
| else |
| { |
| sAlarm->AlarmTime.TimeFormat = 0x00U; |
| assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours)); |
| } |
| assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes)); |
| assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds)); |
| |
| if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay)); |
| } |
| else |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay)); |
| } |
| |
| tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \ |
| ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24U) | \ |
| ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ |
| ((uint32_t)sAlarm->AlarmMask)); |
| } |
| else |
| { |
| if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) |
| { |
| assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); |
| assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); |
| } |
| else |
| { |
| sAlarm->AlarmTime.TimeFormat = 0x00U; |
| assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); |
| } |
| |
| assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes))); |
| assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds))); |
| |
| if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay))); |
| } |
| else |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay))); |
| } |
| |
| tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16U) | \ |
| ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8U) | \ |
| ((uint32_t) sAlarm->AlarmTime.Seconds) | \ |
| ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ |
| ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24U) | \ |
| ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ |
| ((uint32_t)sAlarm->AlarmMask)); |
| } |
| |
| /* Configure the Alarm A or Alarm B Sub Second registers */ |
| subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask)); |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| /* Configure the Alarm register */ |
| if(sAlarm->Alarm == RTC_ALARM_A) |
| { |
| /* Disable the Alarm A interrupt */ |
| __HAL_RTC_ALARMA_DISABLE(hrtc); |
| |
| /* In case of interrupt mode is used, the interrupt source must disabled */ |
| __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */ |
| while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| hrtc->Instance->ALRMAR = (uint32_t)tmpreg; |
| /* Configure the Alarm A Sub Second register */ |
| hrtc->Instance->ALRMASSR = subsecondtmpreg; |
| /* Configure the Alarm state: Enable Alarm */ |
| __HAL_RTC_ALARMA_ENABLE(hrtc); |
| } |
| else |
| { |
| /* Disable the Alarm B interrupt */ |
| __HAL_RTC_ALARMB_DISABLE(hrtc); |
| |
| /* In case of interrupt mode is used, the interrupt source must disabled */ |
| __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRB); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */ |
| while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| hrtc->Instance->ALRMBR = (uint32_t)tmpreg; |
| /* Configure the Alarm B Sub Second register */ |
| hrtc->Instance->ALRMBSSR = subsecondtmpreg; |
| /* Configure the Alarm state: Enable Alarm */ |
| __HAL_RTC_ALARMB_ENABLE(hrtc); |
| } |
| |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| /* Change RTC state */ |
| hrtc->State = HAL_RTC_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Sets the specified RTC Alarm with Interrupt |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sAlarm Pointer to Alarm structure |
| * @param Format Specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format) |
| { |
| uint32_t tmpreg = 0U, subsecondtmpreg = 0U; |
| __IO uint32_t count = RTC_TIMEOUT_VALUE * (SystemCoreClock / 32U / 1000U) ; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| assert_param(IS_RTC_ALARM(sAlarm->Alarm)); |
| assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask)); |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel)); |
| assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds)); |
| assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask)); |
| |
| /* Process Locked */ |
| __HAL_LOCK(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| if(Format == RTC_FORMAT_BIN) |
| { |
| if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) |
| { |
| assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours)); |
| assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); |
| } |
| else |
| { |
| sAlarm->AlarmTime.TimeFormat = 0x00U; |
| assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours)); |
| } |
| assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes)); |
| assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds)); |
| |
| if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay)); |
| } |
| else |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay)); |
| } |
| tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \ |
| ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ |
| ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24U) | \ |
| ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ |
| ((uint32_t)sAlarm->AlarmMask)); |
| } |
| else |
| { |
| if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) |
| { |
| assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); |
| assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); |
| } |
| else |
| { |
| sAlarm->AlarmTime.TimeFormat = 0x00U; |
| assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); |
| } |
| |
| assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes))); |
| assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds))); |
| |
| if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay))); |
| } |
| else |
| { |
| assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay))); |
| } |
| tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16U) | \ |
| ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8U) | \ |
| ((uint32_t) sAlarm->AlarmTime.Seconds) | \ |
| ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16U) | \ |
| ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24U) | \ |
| ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ |
| ((uint32_t)sAlarm->AlarmMask)); |
| } |
| /* Configure the Alarm A or Alarm B Sub Second registers */ |
| subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask)); |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| /* Configure the Alarm register */ |
| if(sAlarm->Alarm == RTC_ALARM_A) |
| { |
| /* Disable the Alarm A interrupt */ |
| __HAL_RTC_ALARMA_DISABLE(hrtc); |
| |
| /* Clear flag alarm A */ |
| __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF); |
| |
| /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */ |
| do |
| { |
| if (count-- == 0U) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| while (__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET); |
| |
| hrtc->Instance->ALRMAR = (uint32_t)tmpreg; |
| /* Configure the Alarm A Sub Second register */ |
| hrtc->Instance->ALRMASSR = subsecondtmpreg; |
| /* Configure the Alarm state: Enable Alarm */ |
| __HAL_RTC_ALARMA_ENABLE(hrtc); |
| /* Configure the Alarm interrupt */ |
| __HAL_RTC_ALARM_ENABLE_IT(hrtc,RTC_IT_ALRA); |
| } |
| else |
| { |
| /* Disable the Alarm B interrupt */ |
| __HAL_RTC_ALARMB_DISABLE(hrtc); |
| |
| /* Clear flag alarm B */ |
| __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF); |
| |
| /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */ |
| do |
| { |
| if (count-- == 0U) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| while (__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET); |
| |
| hrtc->Instance->ALRMBR = (uint32_t)tmpreg; |
| /* Configure the Alarm B Sub Second register */ |
| hrtc->Instance->ALRMBSSR = subsecondtmpreg; |
| /* Configure the Alarm state: Enable Alarm */ |
| __HAL_RTC_ALARMB_ENABLE(hrtc); |
| /* Configure the Alarm interrupt */ |
| __HAL_RTC_ALARM_ENABLE_IT(hrtc, RTC_IT_ALRB); |
| } |
| |
| /* RTC Alarm Interrupt Configuration: EXTI configuration */ |
| __HAL_RTC_ALARM_EXTI_ENABLE_IT(); |
| |
| EXTI->RTSR |= RTC_EXTI_LINE_ALARM_EVENT; |
| |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Deactivate the specified RTC Alarm |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param Alarm Specifies the Alarm. |
| * This parameter can be one of the following values: |
| * @arg RTC_ALARM_A: AlarmA |
| * @arg RTC_ALARM_B: AlarmB |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm) |
| { |
| uint32_t tickstart = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_ALARM(Alarm)); |
| |
| /* Process Locked */ |
| __HAL_LOCK(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_BUSY; |
| |
| /* Disable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| |
| if(Alarm == RTC_ALARM_A) |
| { |
| /* AlarmA */ |
| __HAL_RTC_ALARMA_DISABLE(hrtc); |
| |
| /* In case of interrupt mode is used, the interrupt source must disabled */ |
| __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ |
| while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| else |
| { |
| /* AlarmB */ |
| __HAL_RTC_ALARMB_DISABLE(hrtc); |
| |
| /* In case of interrupt mode is used, the interrupt source must disabled */ |
| __HAL_RTC_ALARM_DISABLE_IT(hrtc,RTC_IT_ALRB); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ |
| while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| /* Enable the write protection for RTC registers */ |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| |
| hrtc->State = HAL_RTC_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hrtc); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Gets the RTC Alarm value and masks. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param sAlarm Pointer to Date structure |
| * @param Alarm Specifies the Alarm. |
| * This parameter can be one of the following values: |
| * @arg RTC_ALARM_A: AlarmA |
| * @arg RTC_ALARM_B: AlarmB |
| * @param Format Specifies the format of the entered parameters. |
| * This parameter can be one of the following values: |
| * @arg RTC_FORMAT_BIN: Binary data format |
| * @arg RTC_FORMAT_BCD: BCD data format |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format) |
| { |
| uint32_t tmpreg = 0U, subsecondtmpreg = 0U; |
| |
| /* Check the parameters */ |
| assert_param(IS_RTC_FORMAT(Format)); |
| assert_param(IS_RTC_ALARM(Alarm)); |
| |
| if(Alarm == RTC_ALARM_A) |
| { |
| /* AlarmA */ |
| sAlarm->Alarm = RTC_ALARM_A; |
| |
| tmpreg = (uint32_t)(hrtc->Instance->ALRMAR); |
| subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMASSR ) & RTC_ALRMASSR_SS); |
| } |
| else |
| { |
| sAlarm->Alarm = RTC_ALARM_B; |
| |
| tmpreg = (uint32_t)(hrtc->Instance->ALRMBR); |
| subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMBSSR) & RTC_ALRMBSSR_SS); |
| } |
| |
| /* Fill the structure with the read parameters */ |
| sAlarm->AlarmTime.Hours = (uint32_t)((tmpreg & (RTC_ALRMAR_HT | RTC_ALRMAR_HU)) >> 16U); |
| sAlarm->AlarmTime.Minutes = (uint32_t)((tmpreg & (RTC_ALRMAR_MNT | RTC_ALRMAR_MNU)) >> 8U); |
| sAlarm->AlarmTime.Seconds = (uint32_t)(tmpreg & (RTC_ALRMAR_ST | RTC_ALRMAR_SU)); |
| sAlarm->AlarmTime.TimeFormat = (uint32_t)((tmpreg & RTC_ALRMAR_PM) >> 16U); |
| sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg; |
| sAlarm->AlarmDateWeekDay = (uint32_t)((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> 24U); |
| sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMAR_WDSEL); |
| sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL); |
| |
| if(Format == RTC_FORMAT_BIN) |
| { |
| sAlarm->AlarmTime.Hours = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); |
| sAlarm->AlarmTime.Minutes = RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes); |
| sAlarm->AlarmTime.Seconds = RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds); |
| sAlarm->AlarmDateWeekDay = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief This function handles Alarm interrupt request. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval None |
| */ |
| void HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef* hrtc) |
| { |
| /* Get the AlarmA interrupt source enable status */ |
| if(__HAL_RTC_ALARM_GET_IT_SOURCE(hrtc, RTC_IT_ALRA) != (uint32_t)RESET) |
| { |
| /* Get the pending status of the AlarmA Interrupt */ |
| if(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) != (uint32_t)RESET) |
| { |
| /* AlarmA callback */ |
| #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) |
| hrtc->AlarmAEventCallback(hrtc); |
| #else |
| HAL_RTC_AlarmAEventCallback(hrtc); |
| #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ |
| |
| /* Clear the AlarmA interrupt pending bit */ |
| __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRAF); |
| } |
| } |
| |
| /* Get the AlarmB interrupt source enable status */ |
| if(__HAL_RTC_ALARM_GET_IT_SOURCE(hrtc, RTC_IT_ALRB) != (uint32_t)RESET) |
| { |
| /* Get the pending status of the AlarmB Interrupt */ |
| if(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBF) != (uint32_t)RESET) |
| { |
| /* AlarmB callback */ |
| #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) |
| hrtc->AlarmBEventCallback(hrtc); |
| #else |
| HAL_RTCEx_AlarmBEventCallback(hrtc); |
| #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ |
| |
| /* Clear the AlarmB interrupt pending bit */ |
| __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRBF); |
| } |
| } |
| |
| /* Clear the EXTI's line Flag for RTC Alarm */ |
| __HAL_RTC_ALARM_EXTI_CLEAR_FLAG(); |
| |
| /* Change RTC state */ |
| hrtc->State = HAL_RTC_STATE_READY; |
| } |
| |
| /** |
| * @brief Alarm A callback. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval None |
| */ |
| __weak void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hrtc); |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_RTC_AlarmAEventCallback could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief This function handles AlarmA Polling request. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @param Timeout Timeout duration |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) |
| { |
| uint32_t tickstart = 0U; |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) == RESET) |
| { |
| if(Timeout != HAL_MAX_DELAY) |
| { |
| if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout)) |
| { |
| hrtc->State = HAL_RTC_STATE_TIMEOUT; |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| /* Clear the Alarm interrupt pending bit */ |
| __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF); |
| |
| /* Change RTC state */ |
| hrtc->State = HAL_RTC_STATE_READY; |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTC_Exported_Functions_Group4 Peripheral Control functions |
| * @brief Peripheral Control functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Peripheral Control functions ##### |
| =============================================================================== |
| [..] |
| This subsection provides functions allowing to |
| (+) Wait for RTC Time and Date Synchronization |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Waits until the RTC Time and Date registers (RTC_TR and RTC_DR) are |
| * synchronized with RTC APB clock. |
| * @note The RTC Resynchronization mode is write protected, use the |
| * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function. |
| * @note To read the calendar through the shadow registers after Calendar |
| * initialization, calendar update or after wake-up from low power modes |
| * the software must first clear the RSF flag. |
| * The software must then wait until it is set again before reading |
| * the calendar, which means that the calendar registers have been |
| * correctly copied into the RTC_TR and RTC_DR shadow registers. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_RTC_WaitForSynchro(RTC_HandleTypeDef* hrtc) |
| { |
| uint32_t tickstart = 0U; |
| |
| /* Clear RSF flag */ |
| hrtc->Instance->ISR &= (uint32_t)RTC_RSF_MASK; |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait the registers to be synchronised */ |
| while((hrtc->Instance->ISR & RTC_ISR_RSF) == (uint32_t)RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup RTC_Exported_Functions_Group5 Peripheral State functions |
| * @brief Peripheral State functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Peripheral State functions ##### |
| =============================================================================== |
| [..] |
| This subsection provides functions allowing to |
| (+) Get RTC state |
| |
| @endverbatim |
| * @{ |
| */ |
| /** |
| * @brief Returns the RTC state. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval HAL state |
| */ |
| HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef* hrtc) |
| { |
| return hrtc->State; |
| } |
| |
| /** |
| * @brief Daylight Saving Time, Add one hour to the calendar in one single operation |
| * without going through the initialization procedure. |
| * @param hrtc RTC handle |
| * @retval None |
| */ |
| void HAL_RTC_DST_Add1Hour(RTC_HandleTypeDef *hrtc) |
| { |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| SET_BIT(hrtc->Instance->CR, RTC_CR_ADD1H); |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| } |
| |
| /** |
| * @brief Daylight Saving Time, Substract one hour from the calendar in one |
| * single operation without going through the initialization procedure. |
| * @param hrtc RTC handle |
| * @retval None |
| */ |
| void HAL_RTC_DST_Sub1Hour(RTC_HandleTypeDef *hrtc) |
| { |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| SET_BIT(hrtc->Instance->CR, RTC_CR_SUB1H); |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| } |
| |
| /** |
| * @brief Daylight Saving Time, Set the store operation bit. |
| * @note It can be used by the software in order to memorize the DST status. |
| * @param hrtc RTC handle |
| * @retval None |
| */ |
| void HAL_RTC_DST_SetStoreOperation(RTC_HandleTypeDef *hrtc) |
| { |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| SET_BIT(hrtc->Instance->CR, RTC_CR_BKP); |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| } |
| |
| /** |
| * @brief Daylight Saving Time, Clear the store operation bit. |
| * @param hrtc RTC handle |
| * @retval None |
| */ |
| void HAL_RTC_DST_ClearStoreOperation(RTC_HandleTypeDef *hrtc) |
| { |
| __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); |
| CLEAR_BIT(hrtc->Instance->CR, RTC_CR_BKP); |
| __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); |
| } |
| |
| /** |
| * @brief Daylight Saving Time, Read the store operation bit. |
| * @param hrtc RTC handle |
| * @retval operation see RTC_StoreOperation_Definitions |
| */ |
| uint32_t HAL_RTC_DST_ReadStoreOperation(RTC_HandleTypeDef *hrtc) |
| { |
| return READ_BIT(hrtc->Instance->CR, RTC_CR_BKP); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @brief Enters the RTC Initialization mode. |
| * @note The RTC Initialization mode is write protected, use the |
| * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function. |
| * @param hrtc pointer to a RTC_HandleTypeDef structure that contains |
| * the configuration information for RTC. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef RTC_EnterInitMode(RTC_HandleTypeDef* hrtc) |
| { |
| uint32_t tickstart = 0U; |
| |
| /* Check if the Initialization mode is set */ |
| if((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET) |
| { |
| /* Set the Initialization mode */ |
| hrtc->Instance->ISR = (uint32_t)RTC_INIT_MASK; |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| /* Wait till RTC is in INIT state and if Time out is reached exit */ |
| while((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET) |
| { |
| if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) |
| { |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief Converts a 2 digit decimal to BCD format. |
| * @param Value Byte to be converted |
| * @retval Converted byte |
| */ |
| uint8_t RTC_ByteToBcd2(uint8_t Value) |
| { |
| uint32_t bcdhigh = 0U; |
| |
| while(Value >= 10U) |
| { |
| bcdhigh++; |
| Value -= 10U; |
| } |
| |
| return ((uint8_t)(bcdhigh << 4U) | Value); |
| } |
| |
| /** |
| * @brief Converts from 2 digit BCD to Binary. |
| * @param Value BCD value to be converted |
| * @retval Converted word |
| */ |
| uint8_t RTC_Bcd2ToByte(uint8_t Value) |
| { |
| uint32_t tmp = 0U; |
| tmp = ((uint8_t)(Value & (uint8_t)0xF0) >> (uint8_t)0x4) * 10; |
| return (tmp + (Value & (uint8_t)0x0F)); |
| } |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* HAL_RTC_MODULE_ENABLED */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |