| /** |
| ****************************************************************************** |
| * @file stm32f4xx_hal_sd.c |
| * @author MCD Application Team |
| * @brief SD card HAL module driver. |
| * This file provides firmware functions to manage the following |
| * functionalities of the Secure Digital (SD) peripheral: |
| * + Initialization and de-initialization functions |
| * + IO operation functions |
| * + Peripheral Control functions |
| * + Peripheral State functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use this driver ##### |
| ============================================================================== |
| [..] |
| This driver implements a high level communication layer for read and write from/to |
| this memory. The needed STM32 hardware resources (SDIO and GPIO) are performed by |
| the user in HAL_SD_MspInit() function (MSP layer). |
| Basically, the MSP layer configuration should be the same as we provide in the |
| examples. |
| You can easily tailor this configuration according to hardware resources. |
| |
| [..] |
| This driver is a generic layered driver for SDIO memories which uses the HAL |
| SDIO driver functions to interface with SD and uSD cards devices. |
| It is used as follows: |
| |
| (#)Initialize the SDIO low level resources by implementing the HAL_SD_MspInit() API: |
| (##) Enable the SDIO interface clock using __HAL_RCC_SDIO_CLK_ENABLE(); |
| (##) SDIO pins configuration for SD card |
| (+++) Enable the clock for the SDIO GPIOs using the functions __HAL_RCC_GPIOx_CLK_ENABLE(); |
| (+++) Configure these SDIO pins as alternate function pull-up using HAL_GPIO_Init() |
| and according to your pin assignment; |
| (##) DMA configuration if you need to use DMA process (HAL_SD_ReadBlocks_DMA() |
| and HAL_SD_WriteBlocks_DMA() APIs). |
| (+++) Enable the DMAx interface clock using __HAL_RCC_DMAx_CLK_ENABLE(); |
| (+++) Configure the DMA using the function HAL_DMA_Init() with predeclared and filled. |
| (##) NVIC configuration if you need to use interrupt process when using DMA transfer. |
| (+++) Configure the SDIO and DMA interrupt priorities using functions |
| HAL_NVIC_SetPriority(); DMA priority is superior to SDIO's priority |
| (+++) Enable the NVIC DMA and SDIO IRQs using function HAL_NVIC_EnableIRQ() |
| (+++) SDIO interrupts are managed using the macros __HAL_SD_ENABLE_IT() |
| and __HAL_SD_DISABLE_IT() inside the communication process. |
| (+++) SDIO interrupts pending bits are managed using the macros __HAL_SD_GET_IT() |
| and __HAL_SD_CLEAR_IT() |
| (##) NVIC configuration if you need to use interrupt process (HAL_SD_ReadBlocks_IT() |
| and HAL_SD_WriteBlocks_IT() APIs). |
| (+++) Configure the SDIO interrupt priorities using function HAL_NVIC_SetPriority(); |
| (+++) Enable the NVIC SDIO IRQs using function HAL_NVIC_EnableIRQ() |
| (+++) SDIO interrupts are managed using the macros __HAL_SD_ENABLE_IT() |
| and __HAL_SD_DISABLE_IT() inside the communication process. |
| (+++) SDIO interrupts pending bits are managed using the macros __HAL_SD_GET_IT() |
| and __HAL_SD_CLEAR_IT() |
| (#) At this stage, you can perform SD read/write/erase operations after SD card initialization |
| |
| |
| *** SD Card Initialization and configuration *** |
| ================================================ |
| [..] |
| To initialize the SD Card, use the HAL_SD_Init() function. It Initializes |
| SDIO Peripheral(STM32 side) and the SD Card, and put it into StandBy State (Ready for data transfer). |
| This function provide the following operations: |
| |
| (#) Apply the SD Card initialization process at 400KHz and check the SD Card |
| type (Standard Capacity or High Capacity). You can change or adapt this |
| frequency by adjusting the "ClockDiv" field. |
| The SD Card frequency (SDIO_CK) is computed as follows: |
| |
| SDIO_CK = SDIOCLK / (ClockDiv + 2) |
| |
| In initialization mode and according to the SD Card standard, |
| make sure that the SDIO_CK frequency doesn't exceed 400KHz. |
| |
| This phase of initialization is done through SDIO_Init() and |
| SDIO_PowerState_ON() SDIO low level APIs. |
| |
| (#) Initialize the SD card. The API used is HAL_SD_InitCard(). |
| This phase allows the card initialization and identification |
| and check the SD Card type (Standard Capacity or High Capacity) |
| The initialization flow is compatible with SD standard. |
| |
| This API (HAL_SD_InitCard()) could be used also to reinitialize the card in case |
| of plug-off plug-in. |
| |
| (#) Configure the SD Card Data transfer frequency. You can change or adapt this |
| frequency by adjusting the "ClockDiv" field. |
| In transfer mode and according to the SD Card standard, make sure that the |
| SDIO_CK frequency doesn't exceed 25MHz and 50MHz in High-speed mode switch. |
| To be able to use a frequency higher than 24MHz, you should use the SDIO |
| peripheral in bypass mode. Refer to the corresponding reference manual |
| for more details. |
| |
| (#) Select the corresponding SD Card according to the address read with the step 2. |
| |
| (#) Configure the SD Card in wide bus mode: 4-bits data. |
| |
| *** SD Card Read operation *** |
| ============================== |
| [..] |
| (+) You can read from SD card in polling mode by using function HAL_SD_ReadBlocks(). |
| This function support only 512-bytes block length (the block size should be |
| chosen as 512 bytes). |
| You can choose either one block read operation or multiple block read operation |
| by adjusting the "NumberOfBlocks" parameter. |
| After this, you have to ensure that the transfer is done correctly. The check is done |
| through HAL_SD_GetCardState() function for SD card state. |
| |
| (+) You can read from SD card in DMA mode by using function HAL_SD_ReadBlocks_DMA(). |
| This function support only 512-bytes block length (the block size should be |
| chosen as 512 bytes). |
| You can choose either one block read operation or multiple block read operation |
| by adjusting the "NumberOfBlocks" parameter. |
| After this, you have to ensure that the transfer is done correctly. The check is done |
| through HAL_SD_GetCardState() function for SD card state. |
| You could also check the DMA transfer process through the SD Rx interrupt event. |
| |
| (+) You can read from SD card in Interrupt mode by using function HAL_SD_ReadBlocks_IT(). |
| This function support only 512-bytes block length (the block size should be |
| chosen as 512 bytes). |
| You can choose either one block read operation or multiple block read operation |
| by adjusting the "NumberOfBlocks" parameter. |
| After this, you have to ensure that the transfer is done correctly. The check is done |
| through HAL_SD_GetCardState() function for SD card state. |
| You could also check the IT transfer process through the SD Rx interrupt event. |
| |
| *** SD Card Write operation *** |
| =============================== |
| [..] |
| (+) You can write to SD card in polling mode by using function HAL_SD_WriteBlocks(). |
| This function support only 512-bytes block length (the block size should be |
| chosen as 512 bytes). |
| You can choose either one block read operation or multiple block read operation |
| by adjusting the "NumberOfBlocks" parameter. |
| After this, you have to ensure that the transfer is done correctly. The check is done |
| through HAL_SD_GetCardState() function for SD card state. |
| |
| (+) You can write to SD card in DMA mode by using function HAL_SD_WriteBlocks_DMA(). |
| This function support only 512-bytes block length (the block size should be |
| chosen as 512 bytes). |
| You can choose either one block read operation or multiple block read operation |
| by adjusting the "NumberOfBlocks" parameter. |
| After this, you have to ensure that the transfer is done correctly. The check is done |
| through HAL_SD_GetCardState() function for SD card state. |
| You could also check the DMA transfer process through the SD Tx interrupt event. |
| |
| (+) You can write to SD card in Interrupt mode by using function HAL_SD_WriteBlocks_IT(). |
| This function support only 512-bytes block length (the block size should be |
| chosen as 512 bytes). |
| You can choose either one block read operation or multiple block read operation |
| by adjusting the "NumberOfBlocks" parameter. |
| After this, you have to ensure that the transfer is done correctly. The check is done |
| through HAL_SD_GetCardState() function for SD card state. |
| You could also check the IT transfer process through the SD Tx interrupt event. |
| |
| *** SD card status *** |
| ====================== |
| [..] |
| (+) The SD Status contains status bits that are related to the SD Memory |
| Card proprietary features. To get SD card status use the HAL_SD_GetCardStatus(). |
| |
| *** SD card information *** |
| =========================== |
| [..] |
| (+) To get SD card information, you can use the function HAL_SD_GetCardInfo(). |
| It returns useful information about the SD card such as block size, card type, |
| block number ... |
| |
| *** SD card CSD register *** |
| ============================ |
| (+) The HAL_SD_GetCardCSD() API allows to get the parameters of the CSD register. |
| Some of the CSD parameters are useful for card initialization and identification. |
| |
| *** SD card CID register *** |
| ============================ |
| (+) The HAL_SD_GetCardCID() API allows to get the parameters of the CID register. |
| Some of the CSD parameters are useful for card initialization and identification. |
| |
| *** SD HAL driver macros list *** |
| ================================== |
| [..] |
| Below the list of most used macros in SD HAL driver. |
| |
| (+) __HAL_SD_ENABLE : Enable the SD device |
| (+) __HAL_SD_DISABLE : Disable the SD device |
| (+) __HAL_SD_DMA_ENABLE: Enable the SDIO DMA transfer |
| (+) __HAL_SD_DMA_DISABLE: Disable the SDIO DMA transfer |
| (+) __HAL_SD_ENABLE_IT: Enable the SD device interrupt |
| (+) __HAL_SD_DISABLE_IT: Disable the SD device interrupt |
| (+) __HAL_SD_GET_FLAG:Check whether the specified SD flag is set or not |
| (+) __HAL_SD_CLEAR_FLAG: Clear the SD's pending flags |
| |
| (@) You can refer to the SD HAL driver header file for more useful macros |
| |
| *** Callback registration *** |
| ============================================= |
| [..] |
| The compilation define USE_HAL_SD_REGISTER_CALLBACKS when set to 1 |
| allows the user to configure dynamically the driver callbacks. |
| |
| Use Functions HAL_SD_RegisterCallback() to register a user callback, |
| it allows to register following callbacks: |
| (+) TxCpltCallback : callback when a transmission transfer is completed. |
| (+) RxCpltCallback : callback when a reception transfer is completed. |
| (+) ErrorCallback : callback when error occurs. |
| (+) AbortCpltCallback : callback when abort is completed. |
| (+) MspInitCallback : SD MspInit. |
| (+) MspDeInitCallback : SD MspDeInit. |
| This function takes as parameters the HAL peripheral handle, the Callback ID |
| and a pointer to the user callback function. |
| |
| Use function HAL_SD_UnRegisterCallback() to reset a callback to the default |
| weak (surcharged) function. It allows to reset following callbacks: |
| (+) TxCpltCallback : callback when a transmission transfer is completed. |
| (+) RxCpltCallback : callback when a reception transfer is completed. |
| (+) ErrorCallback : callback when error occurs. |
| (+) AbortCpltCallback : callback when abort is completed. |
| (+) MspInitCallback : SD MspInit. |
| (+) MspDeInitCallback : SD MspDeInit. |
| This function) takes as parameters the HAL peripheral handle and the Callback ID. |
| |
| By default, after the HAL_SD_Init and if the state is HAL_SD_STATE_RESET |
| all callbacks are reset to the corresponding legacy weak (surcharged) functions. |
| Exception done for MspInit and MspDeInit callbacks that are respectively |
| reset to the legacy weak (surcharged) functions in the HAL_SD_Init |
| and HAL_SD_DeInit only when these callbacks are null (not registered beforehand). |
| If not, MspInit or MspDeInit are not null, the HAL_SD_Init and HAL_SD_DeInit |
| keep and use the user MspInit/MspDeInit callbacks (registered beforehand) |
| |
| Callbacks can be registered/unregistered in READY state only. |
| Exception done for MspInit/MspDeInit callbacks that can be registered/unregistered |
| in READY or RESET state, thus registered (user) MspInit/DeInit callbacks can be used |
| during the Init/DeInit. |
| In that case first register the MspInit/MspDeInit user callbacks |
| using HAL_SD_RegisterCallback before calling HAL_SD_DeInit |
| or HAL_SD_Init function. |
| |
| When The compilation define USE_HAL_SD_REGISTER_CALLBACKS is set to 0 or |
| not defined, the callback registering feature is not available |
| and weak (surcharged) callbacks are used. |
| |
| @endverbatim |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f4xx_hal.h" |
| |
| #if defined(SDIO) |
| |
| /** @addtogroup STM32F4xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup SD |
| * @{ |
| */ |
| |
| #ifdef HAL_SD_MODULE_ENABLED |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /** @addtogroup SD_Private_Defines |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Private functions ---------------------------------------------------------*/ |
| /** @defgroup SD_Private_Functions SD Private Functions |
| * @{ |
| */ |
| static uint32_t SD_InitCard(SD_HandleTypeDef *hsd); |
| static uint32_t SD_PowerON(SD_HandleTypeDef *hsd); |
| static uint32_t SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus); |
| static uint32_t SD_SendStatus(SD_HandleTypeDef *hsd, uint32_t *pCardStatus); |
| static uint32_t SD_WideBus_Enable(SD_HandleTypeDef *hsd); |
| static uint32_t SD_WideBus_Disable(SD_HandleTypeDef *hsd); |
| static uint32_t SD_FindSCR(SD_HandleTypeDef *hsd, uint32_t *pSCR); |
| static void SD_PowerOFF(SD_HandleTypeDef *hsd); |
| static void SD_Write_IT(SD_HandleTypeDef *hsd); |
| static void SD_Read_IT(SD_HandleTypeDef *hsd); |
| static void SD_DMATransmitCplt(DMA_HandleTypeDef *hdma); |
| static void SD_DMAReceiveCplt(DMA_HandleTypeDef *hdma); |
| static void SD_DMAError(DMA_HandleTypeDef *hdma); |
| static void SD_DMATxAbort(DMA_HandleTypeDef *hdma); |
| static void SD_DMARxAbort(DMA_HandleTypeDef *hdma); |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup SD_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup SD_Exported_Functions_Group1 |
| * @brief Initialization and de-initialization functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de-initialization functions ##### |
| ============================================================================== |
| [..] |
| This section provides functions allowing to initialize/de-initialize the SD |
| card device to be ready for use. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the SD according to the specified parameters in the |
| SD_HandleTypeDef and create the associated handle. |
| * @param hsd: Pointer to the SD handle |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_Init(SD_HandleTypeDef *hsd) |
| { |
| /* Check the SD handle allocation */ |
| if(hsd == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Check the parameters */ |
| assert_param(IS_SDIO_ALL_INSTANCE(hsd->Instance)); |
| assert_param(IS_SDIO_CLOCK_EDGE(hsd->Init.ClockEdge)); |
| assert_param(IS_SDIO_CLOCK_BYPASS(hsd->Init.ClockBypass)); |
| assert_param(IS_SDIO_CLOCK_POWER_SAVE(hsd->Init.ClockPowerSave)); |
| assert_param(IS_SDIO_BUS_WIDE(hsd->Init.BusWide)); |
| assert_param(IS_SDIO_HARDWARE_FLOW_CONTROL(hsd->Init.HardwareFlowControl)); |
| assert_param(IS_SDIO_CLKDIV(hsd->Init.ClockDiv)); |
| |
| if(hsd->State == HAL_SD_STATE_RESET) |
| { |
| /* Allocate lock resource and initialize it */ |
| hsd->Lock = HAL_UNLOCKED; |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| /* Reset Callback pointers in HAL_SD_STATE_RESET only */ |
| hsd->TxCpltCallback = HAL_SD_TxCpltCallback; |
| hsd->RxCpltCallback = HAL_SD_RxCpltCallback; |
| hsd->ErrorCallback = HAL_SD_ErrorCallback; |
| hsd->AbortCpltCallback = HAL_SD_AbortCallback; |
| |
| if(hsd->MspInitCallback == NULL) |
| { |
| hsd->MspInitCallback = HAL_SD_MspInit; |
| } |
| |
| /* Init the low level hardware */ |
| hsd->MspInitCallback(hsd); |
| #else |
| /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */ |
| HAL_SD_MspInit(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize the Card parameters */ |
| if (HAL_SD_InitCard(hsd) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Initialize the error code */ |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| /* Initialize the SD operation */ |
| hsd->Context = SD_CONTEXT_NONE; |
| |
| /* Initialize the SD state */ |
| hsd->State = HAL_SD_STATE_READY; |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the SD Card. |
| * @param hsd: Pointer to SD handle |
| * @note This function initializes the SD card. It could be used when a card |
| re-initialization is needed. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_InitCard(SD_HandleTypeDef *hsd) |
| { |
| uint32_t errorstate; |
| HAL_StatusTypeDef status; |
| SD_InitTypeDef Init; |
| |
| /* Default SDIO peripheral configuration for SD card initialization */ |
| Init.ClockEdge = SDIO_CLOCK_EDGE_RISING; |
| Init.ClockBypass = SDIO_CLOCK_BYPASS_DISABLE; |
| Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE; |
| Init.BusWide = SDIO_BUS_WIDE_1B; |
| Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE; |
| Init.ClockDiv = SDIO_INIT_CLK_DIV; |
| |
| /* Initialize SDIO peripheral interface with default configuration */ |
| status = SDIO_Init(hsd->Instance, Init); |
| if(status != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Disable SDIO Clock */ |
| __HAL_SD_DISABLE(hsd); |
| |
| /* Set Power State to ON */ |
| (void)SDIO_PowerState_ON(hsd->Instance); |
| |
| /* Enable SDIO Clock */ |
| __HAL_SD_ENABLE(hsd); |
| |
| /* Identify card operating voltage */ |
| errorstate = SD_PowerON(hsd); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->ErrorCode |= errorstate; |
| return HAL_ERROR; |
| } |
| |
| /* Card initialization */ |
| errorstate = SD_InitCard(hsd); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->ErrorCode |= errorstate; |
| return HAL_ERROR; |
| } |
| |
| /* Set Block Size for Card */ |
| errorstate = SDMMC_CmdBlockLength(hsd->Instance, BLOCKSIZE); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief De-Initializes the SD card. |
| * @param hsd: Pointer to SD handle |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_DeInit(SD_HandleTypeDef *hsd) |
| { |
| /* Check the SD handle allocation */ |
| if(hsd == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Check the parameters */ |
| assert_param(IS_SDIO_ALL_INSTANCE(hsd->Instance)); |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Set SD power state to off */ |
| SD_PowerOFF(hsd); |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| if(hsd->MspDeInitCallback == NULL) |
| { |
| hsd->MspDeInitCallback = HAL_SD_MspDeInit; |
| } |
| |
| /* DeInit the low level hardware */ |
| hsd->MspDeInitCallback(hsd); |
| #else |
| /* De-Initialize the MSP layer */ |
| HAL_SD_MspDeInit(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| hsd->State = HAL_SD_STATE_RESET; |
| |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief Initializes the SD MSP. |
| * @param hsd: Pointer to SD handle |
| * @retval None |
| */ |
| __weak void HAL_SD_MspInit(SD_HandleTypeDef *hsd) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hsd); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_SD_MspInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief De-Initialize SD MSP. |
| * @param hsd: Pointer to SD handle |
| * @retval None |
| */ |
| __weak void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hsd); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_SD_MspDeInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup SD_Exported_Functions_Group2 |
| * @brief Data transfer functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### IO operation functions ##### |
| ============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to manage the data |
| transfer from/to SD card. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Reads block(s) from a specified address in a card. The Data transfer |
| * is managed by polling mode. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @param hsd: Pointer to SD handle |
| * @param pData: pointer to the buffer that will contain the received data |
| * @param BlockAdd: Block Address from where data is to be read |
| * @param NumberOfBlocks: Number of SD blocks to read |
| * @param Timeout: Specify timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t tickstart = HAL_GetTick(); |
| uint32_t count, data, dataremaining; |
| uint32_t add = BlockAdd; |
| uint8_t *tempbuff = pData; |
| |
| if(NULL == pData) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize data control register */ |
| hsd->Instance->DCTRL = 0U; |
| |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| add *= 512U; |
| } |
| |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = NumberOfBlocks * BLOCKSIZE; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| /* Read block(s) in polling mode */ |
| if(NumberOfBlocks > 1U) |
| { |
| hsd->Context = SD_CONTEXT_READ_MULTIPLE_BLOCK; |
| |
| /* Read Multi Block command */ |
| errorstate = SDMMC_CmdReadMultiBlock(hsd->Instance, add); |
| } |
| else |
| { |
| hsd->Context = SD_CONTEXT_READ_SINGLE_BLOCK; |
| |
| /* Read Single Block command */ |
| errorstate = SDMMC_CmdReadSingleBlock(hsd->Instance, add); |
| } |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| |
| /* Poll on SDIO flags */ |
| dataremaining = config.DataLength; |
| #if defined(SDIO_STA_STBITERR) |
| while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND | SDIO_FLAG_STBITERR)) |
| #else /* SDIO_STA_STBITERR not defined */ |
| while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND)) |
| #endif /* SDIO_STA_STBITERR */ |
| { |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXFIFOHF) && (dataremaining > 0U)) |
| { |
| /* Read data from SDIO Rx FIFO */ |
| for(count = 0U; count < 8U; count++) |
| { |
| data = SDIO_ReadFIFO(hsd->Instance); |
| *tempbuff = (uint8_t)(data & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| *tempbuff = (uint8_t)((data >> 8U) & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| *tempbuff = (uint8_t)((data >> 16U) & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| *tempbuff = (uint8_t)((data >> 24U) & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| } |
| } |
| |
| if(((HAL_GetTick()-tickstart) >= Timeout) || (Timeout == 0U)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_TIMEOUT; |
| hsd->State= HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Send stop transmission command in case of multiblock read */ |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DATAEND) && (NumberOfBlocks > 1U)) |
| { |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| /* Send stop transmission command */ |
| errorstate = SDMMC_CmdStopTransfer(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| } |
| } |
| |
| /* Get error state */ |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_CRC_FAIL; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_RX_OVERRUN; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| |
| /* Empty FIFO if there is still any data */ |
| while ((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXDAVL)) && (dataremaining > 0U)) |
| { |
| data = SDIO_ReadFIFO(hsd->Instance); |
| *tempbuff = (uint8_t)(data & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| *tempbuff = (uint8_t)((data >> 8U) & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| *tempbuff = (uint8_t)((data >> 16U) & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| *tempbuff = (uint8_t)((data >> 24U) & 0xFFU); |
| tempbuff++; |
| dataremaining--; |
| |
| if(((HAL_GetTick()-tickstart) >= Timeout) || (Timeout == 0U)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_TIMEOUT; |
| hsd->State= HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| } |
| |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| hsd->State = HAL_SD_STATE_READY; |
| |
| return HAL_OK; |
| } |
| else |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_BUSY; |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Allows to write block(s) to a specified address in a card. The Data |
| * transfer is managed by polling mode. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @param hsd: Pointer to SD handle |
| * @param pData: pointer to the buffer that will contain the data to transmit |
| * @param BlockAdd: Block Address where data will be written |
| * @param NumberOfBlocks: Number of SD blocks to write |
| * @param Timeout: Specify timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t tickstart = HAL_GetTick(); |
| uint32_t count, data, dataremaining; |
| uint32_t add = BlockAdd; |
| uint8_t *tempbuff = pData; |
| |
| if(NULL == pData) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize data control register */ |
| hsd->Instance->DCTRL = 0U; |
| |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| add *= 512U; |
| } |
| |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = NumberOfBlocks * BLOCKSIZE; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_CARD; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| /* Write Blocks in Polling mode */ |
| if(NumberOfBlocks > 1U) |
| { |
| hsd->Context = SD_CONTEXT_WRITE_MULTIPLE_BLOCK; |
| |
| /* Write Multi Block command */ |
| errorstate = SDMMC_CmdWriteMultiBlock(hsd->Instance, add); |
| } |
| else |
| { |
| hsd->Context = SD_CONTEXT_WRITE_SINGLE_BLOCK; |
| |
| /* Write Single Block command */ |
| errorstate = SDMMC_CmdWriteSingleBlock(hsd->Instance, add); |
| } |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| |
| /* Write block(s) in polling mode */ |
| dataremaining = config.DataLength; |
| #if defined(SDIO_STA_STBITERR) |
| while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND | SDIO_FLAG_STBITERR)) |
| #else /* SDIO_STA_STBITERR not defined */ |
| while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND)) |
| #endif /* SDIO_STA_STBITERR */ |
| { |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXFIFOHE) && (dataremaining > 0U)) |
| { |
| /* Write data to SDIO Tx FIFO */ |
| for(count = 0U; count < 8U; count++) |
| { |
| data = (uint32_t)(*tempbuff); |
| tempbuff++; |
| dataremaining--; |
| data |= ((uint32_t)(*tempbuff) << 8U); |
| tempbuff++; |
| dataremaining--; |
| data |= ((uint32_t)(*tempbuff) << 16U); |
| tempbuff++; |
| dataremaining--; |
| data |= ((uint32_t)(*tempbuff) << 24U); |
| tempbuff++; |
| dataremaining--; |
| (void)SDIO_WriteFIFO(hsd->Instance, &data); |
| } |
| } |
| |
| if(((HAL_GetTick()-tickstart) >= Timeout) || (Timeout == 0U)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Send stop transmission command in case of multiblock write */ |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DATAEND) && (NumberOfBlocks > 1U)) |
| { |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| /* Send stop transmission command */ |
| errorstate = SDMMC_CmdStopTransfer(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| } |
| } |
| |
| /* Get error state */ |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_CRC_FAIL; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR)) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_TX_UNDERRUN; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| hsd->State = HAL_SD_STATE_READY; |
| |
| return HAL_OK; |
| } |
| else |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_BUSY; |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Reads block(s) from a specified address in a card. The Data transfer |
| * is managed in interrupt mode. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @note You could also check the IT transfer process through the SD Rx |
| * interrupt event. |
| * @param hsd: Pointer to SD handle |
| * @param pData: Pointer to the buffer that will contain the received data |
| * @param BlockAdd: Block Address from where data is to be read |
| * @param NumberOfBlocks: Number of blocks to read. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_ReadBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t add = BlockAdd; |
| |
| if(NULL == pData) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize data control register */ |
| hsd->Instance->DCTRL = 0U; |
| |
| hsd->pRxBuffPtr = pData; |
| hsd->RxXferSize = BLOCKSIZE * NumberOfBlocks; |
| |
| #if defined(SDIO_STA_STBITERR) |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_FLAG_RXFIFOHF | SDIO_IT_STBITERR)); |
| #else /* SDIO_STA_STBITERR not defined */ |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_FLAG_RXFIFOHF)); |
| #endif /* SDIO_STA_STBITERR */ |
| |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| add *= 512U; |
| } |
| |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = BLOCKSIZE * NumberOfBlocks; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| /* Read Blocks in IT mode */ |
| if(NumberOfBlocks > 1U) |
| { |
| hsd->Context = (SD_CONTEXT_READ_MULTIPLE_BLOCK | SD_CONTEXT_IT); |
| |
| /* Read Multi Block command */ |
| errorstate = SDMMC_CmdReadMultiBlock(hsd->Instance, add); |
| } |
| else |
| { |
| hsd->Context = (SD_CONTEXT_READ_SINGLE_BLOCK | SD_CONTEXT_IT); |
| |
| /* Read Single Block command */ |
| errorstate = SDMMC_CmdReadSingleBlock(hsd->Instance, add); |
| } |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_BUSY; |
| } |
| } |
| |
| /** |
| * @brief Writes block(s) to a specified address in a card. The Data transfer |
| * is managed in interrupt mode. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @note You could also check the IT transfer process through the SD Tx |
| * interrupt event. |
| * @param hsd: Pointer to SD handle |
| * @param pData: Pointer to the buffer that will contain the data to transmit |
| * @param BlockAdd: Block Address where data will be written |
| * @param NumberOfBlocks: Number of blocks to write |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_WriteBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t add = BlockAdd; |
| |
| if(NULL == pData) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize data control register */ |
| hsd->Instance->DCTRL = 0U; |
| |
| hsd->pTxBuffPtr = pData; |
| hsd->TxXferSize = BLOCKSIZE * NumberOfBlocks; |
| |
| /* Enable transfer interrupts */ |
| #if defined(SDIO_STA_STBITERR) |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_DATAEND | SDIO_FLAG_TXFIFOHE | SDIO_IT_STBITERR)); |
| #else /* SDIO_STA_STBITERR not defined */ |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_DATAEND | SDIO_FLAG_TXFIFOHE)); |
| #endif /* SDIO_STA_STBITERR */ |
| |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| add *= 512U; |
| } |
| |
| /* Write Blocks in Polling mode */ |
| if(NumberOfBlocks > 1U) |
| { |
| hsd->Context = (SD_CONTEXT_WRITE_MULTIPLE_BLOCK| SD_CONTEXT_IT); |
| |
| /* Write Multi Block command */ |
| errorstate = SDMMC_CmdWriteMultiBlock(hsd->Instance, add); |
| } |
| else |
| { |
| hsd->Context = (SD_CONTEXT_WRITE_SINGLE_BLOCK | SD_CONTEXT_IT); |
| |
| /* Write Single Block command */ |
| errorstate = SDMMC_CmdWriteSingleBlock(hsd->Instance, add); |
| } |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = BLOCKSIZE * NumberOfBlocks; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_CARD; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_BUSY; |
| } |
| } |
| |
| /** |
| * @brief Reads block(s) from a specified address in a card. The Data transfer |
| * is managed by DMA mode. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @note You could also check the DMA transfer process through the SD Rx |
| * interrupt event. |
| * @param hsd: Pointer SD handle |
| * @param pData: Pointer to the buffer that will contain the received data |
| * @param BlockAdd: Block Address from where data is to be read |
| * @param NumberOfBlocks: Number of blocks to read. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t add = BlockAdd; |
| |
| if(NULL == pData) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize data control register */ |
| hsd->Instance->DCTRL = 0U; |
| |
| #if defined(SDIO_STA_STBITERR) |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_IT_STBITERR)); |
| #else /* SDIO_STA_STBITERR not defined */ |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND)); |
| #endif /* SDIO_STA_STBITERR */ |
| |
| /* Set the DMA transfer complete callback */ |
| hsd->hdmarx->XferCpltCallback = SD_DMAReceiveCplt; |
| |
| /* Set the DMA error callback */ |
| hsd->hdmarx->XferErrorCallback = SD_DMAError; |
| |
| /* Set the DMA Abort callback */ |
| hsd->hdmarx->XferAbortCallback = NULL; |
| |
| /* Force DMA Direction */ |
| hsd->hdmarx->Init.Direction = DMA_PERIPH_TO_MEMORY; |
| MODIFY_REG(hsd->hdmarx->Instance->CR, DMA_SxCR_DIR, hsd->hdmarx->Init.Direction); |
| |
| /* Enable the DMA Channel */ |
| if(HAL_DMA_Start_IT(hsd->hdmarx, (uint32_t)&hsd->Instance->FIFO, (uint32_t)pData, (uint32_t)(BLOCKSIZE * NumberOfBlocks)/4U) != HAL_OK) |
| { |
| __HAL_SD_DISABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND)); |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_DMA; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Enable SD DMA transfer */ |
| __HAL_SD_DMA_ENABLE(hsd); |
| |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| add *= 512U; |
| } |
| |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = BLOCKSIZE * NumberOfBlocks; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| /* Read Blocks in DMA mode */ |
| if(NumberOfBlocks > 1U) |
| { |
| hsd->Context = (SD_CONTEXT_READ_MULTIPLE_BLOCK | SD_CONTEXT_DMA); |
| |
| /* Read Multi Block command */ |
| errorstate = SDMMC_CmdReadMultiBlock(hsd->Instance, add); |
| } |
| else |
| { |
| hsd->Context = (SD_CONTEXT_READ_SINGLE_BLOCK | SD_CONTEXT_DMA); |
| |
| /* Read Single Block command */ |
| errorstate = SDMMC_CmdReadSingleBlock(hsd->Instance, add); |
| } |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| |
| return HAL_OK; |
| } |
| } |
| else |
| { |
| return HAL_BUSY; |
| } |
| } |
| |
| /** |
| * @brief Writes block(s) to a specified address in a card. The Data transfer |
| * is managed by DMA mode. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @note You could also check the DMA transfer process through the SD Tx |
| * interrupt event. |
| * @param hsd: Pointer to SD handle |
| * @param pData: Pointer to the buffer that will contain the data to transmit |
| * @param BlockAdd: Block Address where data will be written |
| * @param NumberOfBlocks: Number of blocks to write |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t add = BlockAdd; |
| |
| if(NULL == pData) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Initialize data control register */ |
| hsd->Instance->DCTRL = 0U; |
| |
| /* Enable SD Error interrupts */ |
| #if defined(SDIO_STA_STBITERR) |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_STBITERR)); |
| #else /* SDIO_STA_STBITERR not defined */ |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR)); |
| #endif /* SDIO_STA_STBITERR */ |
| |
| /* Set the DMA transfer complete callback */ |
| hsd->hdmatx->XferCpltCallback = SD_DMATransmitCplt; |
| |
| /* Set the DMA error callback */ |
| hsd->hdmatx->XferErrorCallback = SD_DMAError; |
| |
| /* Set the DMA Abort callback */ |
| hsd->hdmatx->XferAbortCallback = NULL; |
| |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| add *= 512U; |
| } |
| |
| /* Write Blocks in Polling mode */ |
| if(NumberOfBlocks > 1U) |
| { |
| hsd->Context = (SD_CONTEXT_WRITE_MULTIPLE_BLOCK | SD_CONTEXT_DMA); |
| |
| /* Write Multi Block command */ |
| errorstate = SDMMC_CmdWriteMultiBlock(hsd->Instance, add); |
| } |
| else |
| { |
| hsd->Context = (SD_CONTEXT_WRITE_SINGLE_BLOCK | SD_CONTEXT_DMA); |
| |
| /* Write Single Block command */ |
| errorstate = SDMMC_CmdWriteSingleBlock(hsd->Instance, add); |
| } |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| |
| /* Enable SDIO DMA transfer */ |
| __HAL_SD_DMA_ENABLE(hsd); |
| |
| /* Force DMA Direction */ |
| hsd->hdmatx->Init.Direction = DMA_MEMORY_TO_PERIPH; |
| MODIFY_REG(hsd->hdmatx->Instance->CR, DMA_SxCR_DIR, hsd->hdmatx->Init.Direction); |
| |
| /* Enable the DMA Channel */ |
| if(HAL_DMA_Start_IT(hsd->hdmatx, (uint32_t)pData, (uint32_t)&hsd->Instance->FIFO, (uint32_t)(BLOCKSIZE * NumberOfBlocks)/4U) != HAL_OK) |
| { |
| #if defined(SDIO_STA_STBITERR) |
| __HAL_SD_DISABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_STBITERR)); |
| #else /* SDIO_STA_STBITERR not defined */ |
| __HAL_SD_DISABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR)); |
| #endif /* SDIO_STA_STBITERR */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_DMA; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| return HAL_ERROR; |
| } |
| else |
| { |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = BLOCKSIZE * NumberOfBlocks; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_CARD; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| return HAL_OK; |
| } |
| } |
| else |
| { |
| return HAL_BUSY; |
| } |
| } |
| |
| /** |
| * @brief Erases the specified memory area of the given SD card. |
| * @note This API should be followed by a check on the card state through |
| * HAL_SD_GetCardState(). |
| * @param hsd: Pointer to SD handle |
| * @param BlockStartAdd: Start Block address |
| * @param BlockEndAdd: End Block address |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint32_t BlockStartAdd, uint32_t BlockEndAdd) |
| { |
| uint32_t errorstate; |
| uint32_t start_add = BlockStartAdd; |
| uint32_t end_add = BlockEndAdd; |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| |
| if(end_add < start_add) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| return HAL_ERROR; |
| } |
| |
| if(end_add > (hsd->SdCard.LogBlockNbr)) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| /* Check if the card command class supports erase command */ |
| if(((hsd->SdCard.Class) & SDIO_CCCC_ERASE) == 0U) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_REQUEST_NOT_APPLICABLE; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| |
| if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_LOCK_UNLOCK_FAILED; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| |
| /* Get start and end block for high capacity cards */ |
| if(hsd->SdCard.CardType != CARD_SDHC_SDXC) |
| { |
| start_add *= 512U; |
| end_add *= 512U; |
| } |
| |
| /* According to sd-card spec 1.0 ERASE_GROUP_START (CMD32) and erase_group_end(CMD33) */ |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| /* Send CMD32 SD_ERASE_GRP_START with argument as addr */ |
| errorstate = SDMMC_CmdSDEraseStartAdd(hsd->Instance, start_add); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| |
| /* Send CMD33 SD_ERASE_GRP_END with argument as addr */ |
| errorstate = SDMMC_CmdSDEraseEndAdd(hsd->Instance, end_add); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| } |
| |
| /* Send CMD38 ERASE */ |
| errorstate = SDMMC_CmdErase(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| |
| hsd->State = HAL_SD_STATE_READY; |
| |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_BUSY; |
| } |
| } |
| |
| /** |
| * @brief This function handles SD card interrupt request. |
| * @param hsd: Pointer to SD handle |
| * @retval None |
| */ |
| void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd) |
| { |
| uint32_t errorstate; |
| uint32_t context = hsd->Context; |
| |
| /* Check for SDIO interrupt flags */ |
| if((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXFIFOHF) != RESET) && ((context & SD_CONTEXT_IT) != 0U)) |
| { |
| SD_Read_IT(hsd); |
| } |
| |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DATAEND) != RESET) |
| { |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_DATAEND); |
| |
| #if defined(SDIO_STA_STBITERR) |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR | SDIO_IT_RXOVERR | SDIO_IT_TXFIFOHE |\ |
| SDIO_IT_RXFIFOHF | SDIO_IT_STBITERR); |
| #else /* SDIO_STA_STBITERR not defined */ |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR | SDIO_IT_RXOVERR | SDIO_IT_TXFIFOHE |\ |
| SDIO_IT_RXFIFOHF); |
| #endif /* SDIO_STA_STBITERR */ |
| |
| hsd->Instance->DCTRL &= ~(SDIO_DCTRL_DTEN); |
| |
| if((context & SD_CONTEXT_IT) != 0U) |
| { |
| if(((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U)) |
| { |
| errorstate = SDMMC_CmdStopTransfer(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= errorstate; |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| } |
| |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| if(((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U)) |
| { |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->RxCpltCallback(hsd); |
| #else |
| HAL_SD_RxCpltCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| else |
| { |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->TxCpltCallback(hsd); |
| #else |
| HAL_SD_TxCpltCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| } |
| else if((context & SD_CONTEXT_DMA) != 0U) |
| { |
| if((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U) |
| { |
| errorstate = SDMMC_CmdStopTransfer(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= errorstate; |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| } |
| if(((context & SD_CONTEXT_READ_SINGLE_BLOCK) == 0U) && ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) == 0U)) |
| { |
| /* Disable the DMA transfer for transmit request by setting the DMAEN bit |
| in the SD DCTRL register */ |
| hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); |
| |
| hsd->State = HAL_SD_STATE_READY; |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->TxCpltCallback(hsd); |
| #else |
| HAL_SD_TxCpltCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| } |
| |
| else if((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXFIFOHE) != RESET) && ((context & SD_CONTEXT_IT) != 0U)) |
| { |
| SD_Write_IT(hsd); |
| } |
| |
| #if defined(SDIO_STA_STBITERR) |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_RXOVERR | SDIO_FLAG_TXUNDERR | SDIO_FLAG_STBITERR) != RESET) |
| #else /* SDIO_STA_STBITERR not defined */ |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_RXOVERR | SDIO_FLAG_TXUNDERR) != RESET) |
| #endif /* SDIO_STA_STBITERR */ |
| { |
| /* Set Error code */ |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL) != RESET) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_CRC_FAIL; |
| } |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT) != RESET) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT; |
| } |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR) != RESET) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_RX_OVERRUN; |
| } |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR) != RESET) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_TX_UNDERRUN; |
| } |
| #if defined(SDIO_STA_STBITERR) |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_STBITERR) != RESET) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT; |
| } |
| #endif /* SDIO_STA_STBITERR */ |
| |
| #if defined(SDIO_STA_STBITERR) |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS | SDIO_FLAG_STBITERR); |
| |
| /* Disable all interrupts */ |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR | SDIO_IT_STBITERR); |
| #else /* SDIO_STA_STBITERR not defined */ |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| /* Disable all interrupts */ |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); |
| #endif /* SDIO_STA_STBITERR */ |
| |
| hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance); |
| |
| if((context & SD_CONTEXT_IT) != 0U) |
| { |
| /* Set the SD state to ready to be able to start again the process */ |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| else if((context & SD_CONTEXT_DMA) != 0U) |
| { |
| /* Abort the SD DMA channel */ |
| if(((context & SD_CONTEXT_WRITE_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U)) |
| { |
| /* Set the DMA Tx abort callback */ |
| hsd->hdmatx->XferAbortCallback = SD_DMATxAbort; |
| /* Abort DMA in IT mode */ |
| if(HAL_DMA_Abort_IT(hsd->hdmatx) != HAL_OK) |
| { |
| SD_DMATxAbort(hsd->hdmatx); |
| } |
| } |
| else if(((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U)) |
| { |
| /* Set the DMA Rx abort callback */ |
| hsd->hdmarx->XferAbortCallback = SD_DMARxAbort; |
| /* Abort DMA in IT mode */ |
| if(HAL_DMA_Abort_IT(hsd->hdmarx) != HAL_OK) |
| { |
| SD_DMARxAbort(hsd->hdmarx); |
| } |
| } |
| else |
| { |
| hsd->ErrorCode = HAL_SD_ERROR_NONE; |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->AbortCpltCallback(hsd); |
| #else |
| HAL_SD_AbortCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| } |
| |
| /** |
| * @brief return the SD state |
| * @param hsd: Pointer to sd handle |
| * @retval HAL state |
| */ |
| HAL_SD_StateTypeDef HAL_SD_GetState(SD_HandleTypeDef *hsd) |
| { |
| return hsd->State; |
| } |
| |
| /** |
| * @brief Return the SD error code |
| * @param hsd : Pointer to a SD_HandleTypeDef structure that contains |
| * the configuration information. |
| * @retval SD Error Code |
| */ |
| uint32_t HAL_SD_GetError(SD_HandleTypeDef *hsd) |
| { |
| return hsd->ErrorCode; |
| } |
| |
| /** |
| * @brief Tx Transfer completed callbacks |
| * @param hsd: Pointer to SD handle |
| * @retval None |
| */ |
| __weak void HAL_SD_TxCpltCallback(SD_HandleTypeDef *hsd) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hsd); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_SD_TxCpltCallback can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief Rx Transfer completed callbacks |
| * @param hsd: Pointer SD handle |
| * @retval None |
| */ |
| __weak void HAL_SD_RxCpltCallback(SD_HandleTypeDef *hsd) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hsd); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_SD_RxCpltCallback can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief SD error callbacks |
| * @param hsd: Pointer SD handle |
| * @retval None |
| */ |
| __weak void HAL_SD_ErrorCallback(SD_HandleTypeDef *hsd) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hsd); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_SD_ErrorCallback can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief SD Abort callbacks |
| * @param hsd: Pointer SD handle |
| * @retval None |
| */ |
| __weak void HAL_SD_AbortCallback(SD_HandleTypeDef *hsd) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hsd); |
| |
| /* NOTE : This function should not be modified, when the callback is needed, |
| the HAL_SD_AbortCallback can be implemented in the user file |
| */ |
| } |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| /** |
| * @brief Register a User SD Callback |
| * To be used instead of the weak (surcharged) predefined callback |
| * @param hsd : SD handle |
| * @param CallbackID : ID of the callback to be registered |
| * This parameter can be one of the following values: |
| * @arg @ref HAL_SD_TX_CPLT_CB_ID SD Tx Complete Callback ID |
| * @arg @ref HAL_SD_RX_CPLT_CB_ID SD Rx Complete Callback ID |
| * @arg @ref HAL_SD_ERROR_CB_ID SD Error Callback ID |
| * @arg @ref HAL_SD_ABORT_CB_ID SD Abort Callback ID |
| * @arg @ref HAL_SD_MSP_INIT_CB_ID SD MspInit Callback ID |
| * @arg @ref HAL_SD_MSP_DEINIT_CB_ID SD MspDeInit Callback ID |
| * @param pCallback : pointer to the Callback function |
| * @retval status |
| */ |
| HAL_StatusTypeDef HAL_SD_RegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackID, pSD_CallbackTypeDef pCallback) |
| { |
| HAL_StatusTypeDef status = HAL_OK; |
| |
| if(pCallback == NULL) |
| { |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| return HAL_ERROR; |
| } |
| |
| /* Process locked */ |
| __HAL_LOCK(hsd); |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| switch (CallbackID) |
| { |
| case HAL_SD_TX_CPLT_CB_ID : |
| hsd->TxCpltCallback = pCallback; |
| break; |
| case HAL_SD_RX_CPLT_CB_ID : |
| hsd->RxCpltCallback = pCallback; |
| break; |
| case HAL_SD_ERROR_CB_ID : |
| hsd->ErrorCallback = pCallback; |
| break; |
| case HAL_SD_ABORT_CB_ID : |
| hsd->AbortCpltCallback = pCallback; |
| break; |
| case HAL_SD_MSP_INIT_CB_ID : |
| hsd->MspInitCallback = pCallback; |
| break; |
| case HAL_SD_MSP_DEINIT_CB_ID : |
| hsd->MspDeInitCallback = pCallback; |
| break; |
| default : |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| /* update return status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else if (hsd->State == HAL_SD_STATE_RESET) |
| { |
| switch (CallbackID) |
| { |
| case HAL_SD_MSP_INIT_CB_ID : |
| hsd->MspInitCallback = pCallback; |
| break; |
| case HAL_SD_MSP_DEINIT_CB_ID : |
| hsd->MspDeInitCallback = pCallback; |
| break; |
| default : |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| /* update return status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else |
| { |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| /* update return status */ |
| status = HAL_ERROR; |
| } |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hsd); |
| return status; |
| } |
| |
| /** |
| * @brief Unregister a User SD Callback |
| * SD Callback is redirected to the weak (surcharged) predefined callback |
| * @param hsd : SD handle |
| * @param CallbackID : ID of the callback to be unregistered |
| * This parameter can be one of the following values: |
| * @arg @ref HAL_SD_TX_CPLT_CB_ID SD Tx Complete Callback ID |
| * @arg @ref HAL_SD_RX_CPLT_CB_ID SD Rx Complete Callback ID |
| * @arg @ref HAL_SD_ERROR_CB_ID SD Error Callback ID |
| * @arg @ref HAL_SD_ABORT_CB_ID SD Abort Callback ID |
| * @arg @ref HAL_SD_MSP_INIT_CB_ID SD MspInit Callback ID |
| * @arg @ref HAL_SD_MSP_DEINIT_CB_ID SD MspDeInit Callback ID |
| * @retval status |
| */ |
| HAL_StatusTypeDef HAL_SD_UnRegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackID) |
| { |
| HAL_StatusTypeDef status = HAL_OK; |
| |
| /* Process locked */ |
| __HAL_LOCK(hsd); |
| |
| if(hsd->State == HAL_SD_STATE_READY) |
| { |
| switch (CallbackID) |
| { |
| case HAL_SD_TX_CPLT_CB_ID : |
| hsd->TxCpltCallback = HAL_SD_TxCpltCallback; |
| break; |
| case HAL_SD_RX_CPLT_CB_ID : |
| hsd->RxCpltCallback = HAL_SD_RxCpltCallback; |
| break; |
| case HAL_SD_ERROR_CB_ID : |
| hsd->ErrorCallback = HAL_SD_ErrorCallback; |
| break; |
| case HAL_SD_ABORT_CB_ID : |
| hsd->AbortCpltCallback = HAL_SD_AbortCallback; |
| break; |
| case HAL_SD_MSP_INIT_CB_ID : |
| hsd->MspInitCallback = HAL_SD_MspInit; |
| break; |
| case HAL_SD_MSP_DEINIT_CB_ID : |
| hsd->MspDeInitCallback = HAL_SD_MspDeInit; |
| break; |
| default : |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| /* update return status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else if (hsd->State == HAL_SD_STATE_RESET) |
| { |
| switch (CallbackID) |
| { |
| case HAL_SD_MSP_INIT_CB_ID : |
| hsd->MspInitCallback = HAL_SD_MspInit; |
| break; |
| case HAL_SD_MSP_DEINIT_CB_ID : |
| hsd->MspDeInitCallback = HAL_SD_MspDeInit; |
| break; |
| default : |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| /* update return status */ |
| status = HAL_ERROR; |
| break; |
| } |
| } |
| else |
| { |
| /* Update the error code */ |
| hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK; |
| /* update return status */ |
| status = HAL_ERROR; |
| } |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hsd); |
| return status; |
| } |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup SD_Exported_Functions_Group3 |
| * @brief management functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### Peripheral Control functions ##### |
| ============================================================================== |
| [..] |
| This subsection provides a set of functions allowing to control the SD card |
| operations and get the related information |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Returns information the information of the card which are stored on |
| * the CID register. |
| * @param hsd: Pointer to SD handle |
| * @param pCID: Pointer to a HAL_SD_CardCIDTypeDef structure that |
| * contains all CID register parameters |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_GetCardCID(SD_HandleTypeDef *hsd, HAL_SD_CardCIDTypeDef *pCID) |
| { |
| pCID->ManufacturerID = (uint8_t)((hsd->CID[0] & 0xFF000000U) >> 24U); |
| |
| pCID->OEM_AppliID = (uint16_t)((hsd->CID[0] & 0x00FFFF00U) >> 8U); |
| |
| pCID->ProdName1 = (((hsd->CID[0] & 0x000000FFU) << 24U) | ((hsd->CID[1] & 0xFFFFFF00U) >> 8U)); |
| |
| pCID->ProdName2 = (uint8_t)(hsd->CID[1] & 0x000000FFU); |
| |
| pCID->ProdRev = (uint8_t)((hsd->CID[2] & 0xFF000000U) >> 24U); |
| |
| pCID->ProdSN = (((hsd->CID[2] & 0x00FFFFFFU) << 8U) | ((hsd->CID[3] & 0xFF000000U) >> 24U)); |
| |
| pCID->Reserved1 = (uint8_t)((hsd->CID[3] & 0x00F00000U) >> 20U); |
| |
| pCID->ManufactDate = (uint16_t)((hsd->CID[3] & 0x000FFF00U) >> 8U); |
| |
| pCID->CID_CRC = (uint8_t)((hsd->CID[3] & 0x000000FEU) >> 1U); |
| |
| pCID->Reserved2 = 1U; |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Returns information the information of the card which are stored on |
| * the CSD register. |
| * @param hsd: Pointer to SD handle |
| * @param pCSD: Pointer to a HAL_SD_CardCSDTypeDef structure that |
| * contains all CSD register parameters |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_GetCardCSD(SD_HandleTypeDef *hsd, HAL_SD_CardCSDTypeDef *pCSD) |
| { |
| pCSD->CSDStruct = (uint8_t)((hsd->CSD[0] & 0xC0000000U) >> 30U); |
| |
| pCSD->SysSpecVersion = (uint8_t)((hsd->CSD[0] & 0x3C000000U) >> 26U); |
| |
| pCSD->Reserved1 = (uint8_t)((hsd->CSD[0] & 0x03000000U) >> 24U); |
| |
| pCSD->TAAC = (uint8_t)((hsd->CSD[0] & 0x00FF0000U) >> 16U); |
| |
| pCSD->NSAC = (uint8_t)((hsd->CSD[0] & 0x0000FF00U) >> 8U); |
| |
| pCSD->MaxBusClkFrec = (uint8_t)(hsd->CSD[0] & 0x000000FFU); |
| |
| pCSD->CardComdClasses = (uint16_t)((hsd->CSD[1] & 0xFFF00000U) >> 20U); |
| |
| pCSD->RdBlockLen = (uint8_t)((hsd->CSD[1] & 0x000F0000U) >> 16U); |
| |
| pCSD->PartBlockRead = (uint8_t)((hsd->CSD[1] & 0x00008000U) >> 15U); |
| |
| pCSD->WrBlockMisalign = (uint8_t)((hsd->CSD[1] & 0x00004000U) >> 14U); |
| |
| pCSD->RdBlockMisalign = (uint8_t)((hsd->CSD[1] & 0x00002000U) >> 13U); |
| |
| pCSD->DSRImpl = (uint8_t)((hsd->CSD[1] & 0x00001000U) >> 12U); |
| |
| pCSD->Reserved2 = 0U; /*!< Reserved */ |
| |
| if(hsd->SdCard.CardType == CARD_SDSC) |
| { |
| pCSD->DeviceSize = (((hsd->CSD[1] & 0x000003FFU) << 2U) | ((hsd->CSD[2] & 0xC0000000U) >> 30U)); |
| |
| pCSD->MaxRdCurrentVDDMin = (uint8_t)((hsd->CSD[2] & 0x38000000U) >> 27U); |
| |
| pCSD->MaxRdCurrentVDDMax = (uint8_t)((hsd->CSD[2] & 0x07000000U) >> 24U); |
| |
| pCSD->MaxWrCurrentVDDMin = (uint8_t)((hsd->CSD[2] & 0x00E00000U) >> 21U); |
| |
| pCSD->MaxWrCurrentVDDMax = (uint8_t)((hsd->CSD[2] & 0x001C0000U) >> 18U); |
| |
| pCSD->DeviceSizeMul = (uint8_t)((hsd->CSD[2] & 0x00038000U) >> 15U); |
| |
| hsd->SdCard.BlockNbr = (pCSD->DeviceSize + 1U) ; |
| hsd->SdCard.BlockNbr *= (1UL << ((pCSD->DeviceSizeMul & 0x07U) + 2U)); |
| hsd->SdCard.BlockSize = (1UL << (pCSD->RdBlockLen & 0x0FU)); |
| |
| hsd->SdCard.LogBlockNbr = (hsd->SdCard.BlockNbr) * ((hsd->SdCard.BlockSize) / 512U); |
| hsd->SdCard.LogBlockSize = 512U; |
| } |
| else if(hsd->SdCard.CardType == CARD_SDHC_SDXC) |
| { |
| /* Byte 7 */ |
| pCSD->DeviceSize = (((hsd->CSD[1] & 0x0000003FU) << 16U) | ((hsd->CSD[2] & 0xFFFF0000U) >> 16U)); |
| |
| hsd->SdCard.BlockNbr = ((pCSD->DeviceSize + 1U) * 1024U); |
| hsd->SdCard.LogBlockNbr = hsd->SdCard.BlockNbr; |
| hsd->SdCard.BlockSize = 512U; |
| hsd->SdCard.LogBlockSize = hsd->SdCard.BlockSize; |
| } |
| else |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= HAL_SD_ERROR_UNSUPPORTED_FEATURE; |
| hsd->State = HAL_SD_STATE_READY; |
| return HAL_ERROR; |
| } |
| |
| pCSD->EraseGrSize = (uint8_t)((hsd->CSD[2] & 0x00004000U) >> 14U); |
| |
| pCSD->EraseGrMul = (uint8_t)((hsd->CSD[2] & 0x00003F80U) >> 7U); |
| |
| pCSD->WrProtectGrSize = (uint8_t)(hsd->CSD[2] & 0x0000007FU); |
| |
| pCSD->WrProtectGrEnable = (uint8_t)((hsd->CSD[3] & 0x80000000U) >> 31U); |
| |
| pCSD->ManDeflECC = (uint8_t)((hsd->CSD[3] & 0x60000000U) >> 29U); |
| |
| pCSD->WrSpeedFact = (uint8_t)((hsd->CSD[3] & 0x1C000000U) >> 26U); |
| |
| pCSD->MaxWrBlockLen= (uint8_t)((hsd->CSD[3] & 0x03C00000U) >> 22U); |
| |
| pCSD->WriteBlockPaPartial = (uint8_t)((hsd->CSD[3] & 0x00200000U) >> 21U); |
| |
| pCSD->Reserved3 = 0; |
| |
| pCSD->ContentProtectAppli = (uint8_t)((hsd->CSD[3] & 0x00010000U) >> 16U); |
| |
| pCSD->FileFormatGroup = (uint8_t)((hsd->CSD[3] & 0x00008000U) >> 15U); |
| |
| pCSD->CopyFlag = (uint8_t)((hsd->CSD[3] & 0x00004000U) >> 14U); |
| |
| pCSD->PermWrProtect = (uint8_t)((hsd->CSD[3] & 0x00002000U) >> 13U); |
| |
| pCSD->TempWrProtect = (uint8_t)((hsd->CSD[3] & 0x00001000U) >> 12U); |
| |
| pCSD->FileFormat = (uint8_t)((hsd->CSD[3] & 0x00000C00U) >> 10U); |
| |
| pCSD->ECC= (uint8_t)((hsd->CSD[3] & 0x00000300U) >> 8U); |
| |
| pCSD->CSD_CRC = (uint8_t)((hsd->CSD[3] & 0x000000FEU) >> 1U); |
| |
| pCSD->Reserved4 = 1; |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Gets the SD status info. |
| * @param hsd: Pointer to SD handle |
| * @param pStatus: Pointer to the HAL_SD_CardStatusTypeDef structure that |
| * will contain the SD card status information |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypeDef *pStatus) |
| { |
| uint32_t sd_status[16]; |
| uint32_t errorstate; |
| HAL_StatusTypeDef status = HAL_OK; |
| |
| errorstate = SD_SendSDStatus(hsd, sd_status); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| status = HAL_ERROR; |
| } |
| else |
| { |
| pStatus->DataBusWidth = (uint8_t)((sd_status[0] & 0xC0U) >> 6U); |
| |
| pStatus->SecuredMode = (uint8_t)((sd_status[0] & 0x20U) >> 5U); |
| |
| pStatus->CardType = (uint16_t)(((sd_status[0] & 0x00FF0000U) >> 8U) | ((sd_status[0] & 0xFF000000U) >> 24U)); |
| |
| pStatus->ProtectedAreaSize = (((sd_status[1] & 0xFFU) << 24U) | ((sd_status[1] & 0xFF00U) << 8U) | |
| ((sd_status[1] & 0xFF0000U) >> 8U) | ((sd_status[1] & 0xFF000000U) >> 24U)); |
| |
| pStatus->SpeedClass = (uint8_t)(sd_status[2] & 0xFFU); |
| |
| pStatus->PerformanceMove = (uint8_t)((sd_status[2] & 0xFF00U) >> 8U); |
| |
| pStatus->AllocationUnitSize = (uint8_t)((sd_status[2] & 0xF00000U) >> 20U); |
| |
| pStatus->EraseSize = (uint16_t)(((sd_status[2] & 0xFF000000U) >> 16U) | (sd_status[3] & 0xFFU)); |
| |
| pStatus->EraseTimeout = (uint8_t)((sd_status[3] & 0xFC00U) >> 10U); |
| |
| pStatus->EraseOffset = (uint8_t)((sd_status[3] & 0x0300U) >> 8U); |
| } |
| |
| /* Set Block Size for Card */ |
| errorstate = SDMMC_CmdBlockLength(hsd->Instance, BLOCKSIZE); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode = errorstate; |
| hsd->State = HAL_SD_STATE_READY; |
| status = HAL_ERROR; |
| } |
| |
| return status; |
| } |
| |
| /** |
| * @brief Gets the SD card info. |
| * @param hsd: Pointer to SD handle |
| * @param pCardInfo: Pointer to the HAL_SD_CardInfoTypeDef structure that |
| * will contain the SD card status information |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_GetCardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypeDef *pCardInfo) |
| { |
| pCardInfo->CardType = (uint32_t)(hsd->SdCard.CardType); |
| pCardInfo->CardVersion = (uint32_t)(hsd->SdCard.CardVersion); |
| pCardInfo->Class = (uint32_t)(hsd->SdCard.Class); |
| pCardInfo->RelCardAdd = (uint32_t)(hsd->SdCard.RelCardAdd); |
| pCardInfo->BlockNbr = (uint32_t)(hsd->SdCard.BlockNbr); |
| pCardInfo->BlockSize = (uint32_t)(hsd->SdCard.BlockSize); |
| pCardInfo->LogBlockNbr = (uint32_t)(hsd->SdCard.LogBlockNbr); |
| pCardInfo->LogBlockSize = (uint32_t)(hsd->SdCard.LogBlockSize); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Enables wide bus operation for the requested card if supported by |
| * card. |
| * @param hsd: Pointer to SD handle |
| * @param WideMode: Specifies the SD card wide bus mode |
| * This parameter can be one of the following values: |
| * @arg SDIO_BUS_WIDE_8B: 8-bit data transfer |
| * @arg SDIO_BUS_WIDE_4B: 4-bit data transfer |
| * @arg SDIO_BUS_WIDE_1B: 1-bit data transfer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_ConfigWideBusOperation(SD_HandleTypeDef *hsd, uint32_t WideMode) |
| { |
| SDIO_InitTypeDef Init; |
| uint32_t errorstate; |
| HAL_StatusTypeDef status = HAL_OK; |
| |
| /* Check the parameters */ |
| assert_param(IS_SDIO_BUS_WIDE(WideMode)); |
| |
| /* Change State */ |
| hsd->State = HAL_SD_STATE_BUSY; |
| |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| if(WideMode == SDIO_BUS_WIDE_8B) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_UNSUPPORTED_FEATURE; |
| } |
| else if(WideMode == SDIO_BUS_WIDE_4B) |
| { |
| errorstate = SD_WideBus_Enable(hsd); |
| |
| hsd->ErrorCode |= errorstate; |
| } |
| else if(WideMode == SDIO_BUS_WIDE_1B) |
| { |
| errorstate = SD_WideBus_Disable(hsd); |
| |
| hsd->ErrorCode |= errorstate; |
| } |
| else |
| { |
| /* WideMode is not a valid argument*/ |
| hsd->ErrorCode |= HAL_SD_ERROR_PARAM; |
| } |
| } |
| else |
| { |
| /* MMC Card does not support this feature */ |
| hsd->ErrorCode |= HAL_SD_ERROR_UNSUPPORTED_FEATURE; |
| } |
| |
| if(hsd->ErrorCode != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->State = HAL_SD_STATE_READY; |
| status = HAL_ERROR; |
| } |
| else |
| { |
| /* Configure the SDIO peripheral */ |
| Init.ClockEdge = hsd->Init.ClockEdge; |
| Init.ClockBypass = hsd->Init.ClockBypass; |
| Init.ClockPowerSave = hsd->Init.ClockPowerSave; |
| Init.BusWide = WideMode; |
| Init.HardwareFlowControl = hsd->Init.HardwareFlowControl; |
| Init.ClockDiv = hsd->Init.ClockDiv; |
| (void)SDIO_Init(hsd->Instance, Init); |
| } |
| |
| /* Set Block Size for Card */ |
| errorstate = SDMMC_CmdBlockLength(hsd->Instance, BLOCKSIZE); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| hsd->ErrorCode |= errorstate; |
| status = HAL_ERROR; |
| } |
| |
| /* Change State */ |
| hsd->State = HAL_SD_STATE_READY; |
| |
| return status; |
| } |
| |
| /** |
| * @brief Gets the current sd card data state. |
| * @param hsd: pointer to SD handle |
| * @retval Card state |
| */ |
| HAL_SD_CardStateTypeDef HAL_SD_GetCardState(SD_HandleTypeDef *hsd) |
| { |
| uint32_t cardstate; |
| uint32_t errorstate; |
| uint32_t resp1 = 0; |
| |
| errorstate = SD_SendStatus(hsd, &resp1); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= errorstate; |
| } |
| |
| cardstate = ((resp1 >> 9U) & 0x0FU); |
| |
| return (HAL_SD_CardStateTypeDef)cardstate; |
| } |
| |
| /** |
| * @brief Abort the current transfer and disable the SD. |
| * @param hsd: pointer to a SD_HandleTypeDef structure that contains |
| * the configuration information for SD module. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_Abort(SD_HandleTypeDef *hsd) |
| { |
| HAL_SD_CardStateTypeDef CardState; |
| uint32_t context = hsd->Context; |
| |
| /* DIsable All interrupts */ |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); |
| |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| CLEAR_BIT(hsd->Instance->DCTRL, SDIO_DCTRL_DTEN); |
| |
| if ((context & SD_CONTEXT_DMA) != 0U) |
| { |
| /* Disable the SD DMA request */ |
| hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); |
| |
| /* Abort the SD DMA Tx channel */ |
| if (((context & SD_CONTEXT_WRITE_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U)) |
| { |
| if(HAL_DMA_Abort(hsd->hdmatx) != HAL_OK) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_DMA; |
| } |
| } |
| /* Abort the SD DMA Rx channel */ |
| else if (((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U)) |
| { |
| if(HAL_DMA_Abort(hsd->hdmarx) != HAL_OK) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_DMA; |
| } |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| } |
| |
| hsd->State = HAL_SD_STATE_READY; |
| |
| /* Initialize the SD operation */ |
| hsd->Context = SD_CONTEXT_NONE; |
| |
| CardState = HAL_SD_GetCardState(hsd); |
| if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING)) |
| { |
| hsd->ErrorCode = SDMMC_CmdStopTransfer(hsd->Instance); |
| } |
| if(hsd->ErrorCode != HAL_SD_ERROR_NONE) |
| { |
| return HAL_ERROR; |
| } |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Abort the current transfer and disable the SD (IT mode). |
| * @param hsd: pointer to a SD_HandleTypeDef structure that contains |
| * the configuration information for SD module. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_SD_Abort_IT(SD_HandleTypeDef *hsd) |
| { |
| HAL_SD_CardStateTypeDef CardState; |
| uint32_t context = hsd->Context; |
| |
| /* Disable All interrupts */ |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); |
| |
| CLEAR_BIT(hsd->Instance->DCTRL, SDIO_DCTRL_DTEN); |
| |
| if ((context & SD_CONTEXT_DMA) != 0U) |
| { |
| /* Disable the SD DMA request */ |
| hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); |
| |
| /* Abort the SD DMA Tx channel */ |
| if (((context & SD_CONTEXT_WRITE_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U)) |
| { |
| hsd->hdmatx->XferAbortCallback = SD_DMATxAbort; |
| if(HAL_DMA_Abort_IT(hsd->hdmatx) != HAL_OK) |
| { |
| hsd->hdmatx = NULL; |
| } |
| } |
| /* Abort the SD DMA Rx channel */ |
| else if (((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U)) |
| { |
| hsd->hdmarx->XferAbortCallback = SD_DMARxAbort; |
| if(HAL_DMA_Abort_IT(hsd->hdmarx) != HAL_OK) |
| { |
| hsd->hdmarx = NULL; |
| } |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| } |
| /* No transfer ongoing on both DMA channels*/ |
| else |
| { |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| CardState = HAL_SD_GetCardState(hsd); |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING)) |
| { |
| hsd->ErrorCode = SDMMC_CmdStopTransfer(hsd->Instance); |
| } |
| if(hsd->ErrorCode != HAL_SD_ERROR_NONE) |
| { |
| return HAL_ERROR; |
| } |
| else |
| { |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| hsd->AbortCpltCallback(hsd); |
| #else |
| HAL_SD_AbortCallback(hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| } |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private function ----------------------------------------------------------*/ |
| /** @addtogroup SD_Private_Functions |
| * @{ |
| */ |
| |
| /** |
| * @brief DMA SD transmit process complete callback |
| * @param hdma: DMA handle |
| * @retval None |
| */ |
| static void SD_DMATransmitCplt(DMA_HandleTypeDef *hdma) |
| { |
| SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent); |
| |
| /* Enable DATAEND Interrupt */ |
| __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DATAEND)); |
| } |
| |
| /** |
| * @brief DMA SD receive process complete callback |
| * @param hdma: DMA handle |
| * @retval None |
| */ |
| static void SD_DMAReceiveCplt(DMA_HandleTypeDef *hdma) |
| { |
| SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent); |
| uint32_t errorstate; |
| |
| /* Send stop command in multiblock write */ |
| if(hsd->Context == (SD_CONTEXT_READ_MULTIPLE_BLOCK | SD_CONTEXT_DMA)) |
| { |
| errorstate = SDMMC_CmdStopTransfer(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= errorstate; |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif |
| } |
| } |
| |
| /* Disable the DMA transfer for transmit request by setting the DMAEN bit |
| in the SD DCTRL register */ |
| hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); |
| |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->RxCpltCallback(hsd); |
| #else |
| HAL_SD_RxCpltCallback(hsd); |
| #endif |
| } |
| |
| /** |
| * @brief DMA SD communication error callback |
| * @param hdma: DMA handle |
| * @retval None |
| */ |
| static void SD_DMAError(DMA_HandleTypeDef *hdma) |
| { |
| SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent); |
| HAL_SD_CardStateTypeDef CardState; |
| uint32_t RxErrorCode, TxErrorCode; |
| |
| /* if DMA error is FIFO error ignore it */ |
| if(HAL_DMA_GetError(hdma) != HAL_DMA_ERROR_FE) |
| { |
| RxErrorCode = hsd->hdmarx->ErrorCode; |
| TxErrorCode = hsd->hdmatx->ErrorCode; |
| if((RxErrorCode == HAL_DMA_ERROR_TE) || (TxErrorCode == HAL_DMA_ERROR_TE)) |
| { |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS); |
| |
| /* Disable All interrupts */ |
| __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ |
| SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); |
| |
| hsd->ErrorCode |= HAL_SD_ERROR_DMA; |
| CardState = HAL_SD_GetCardState(hsd); |
| if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING)) |
| { |
| hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance); |
| } |
| |
| hsd->State= HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| } |
| |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif |
| } |
| } |
| |
| /** |
| * @brief DMA SD Tx Abort callback |
| * @param hdma: DMA handle |
| * @retval None |
| */ |
| static void SD_DMATxAbort(DMA_HandleTypeDef *hdma) |
| { |
| SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent); |
| HAL_SD_CardStateTypeDef CardState; |
| |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| CardState = HAL_SD_GetCardState(hsd); |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING)) |
| { |
| hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance); |
| } |
| |
| if(hsd->ErrorCode == HAL_SD_ERROR_NONE) |
| { |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->AbortCpltCallback(hsd); |
| #else |
| HAL_SD_AbortCallback(hsd); |
| #endif |
| } |
| else |
| { |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif |
| } |
| } |
| |
| /** |
| * @brief DMA SD Rx Abort callback |
| * @param hdma: DMA handle |
| * @retval None |
| */ |
| static void SD_DMARxAbort(DMA_HandleTypeDef *hdma) |
| { |
| SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent); |
| HAL_SD_CardStateTypeDef CardState; |
| |
| /* Clear All flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| CardState = HAL_SD_GetCardState(hsd); |
| hsd->State = HAL_SD_STATE_READY; |
| hsd->Context = SD_CONTEXT_NONE; |
| if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING)) |
| { |
| hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance); |
| } |
| |
| if(hsd->ErrorCode == HAL_SD_ERROR_NONE) |
| { |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->AbortCpltCallback(hsd); |
| #else |
| HAL_SD_AbortCallback(hsd); |
| #endif |
| } |
| else |
| { |
| #if (USE_HAL_SD_REGISTER_CALLBACKS == 1) |
| hsd->ErrorCallback(hsd); |
| #else |
| HAL_SD_ErrorCallback(hsd); |
| #endif |
| } |
| } |
| |
| /** |
| * @brief Initializes the sd card. |
| * @param hsd: Pointer to SD handle |
| * @retval SD Card error state |
| */ |
| static uint32_t SD_InitCard(SD_HandleTypeDef *hsd) |
| { |
| HAL_SD_CardCSDTypeDef CSD; |
| uint32_t errorstate; |
| uint16_t sd_rca = 1U; |
| |
| /* Check the power State */ |
| if(SDIO_GetPowerState(hsd->Instance) == 0U) |
| { |
| /* Power off */ |
| return HAL_SD_ERROR_REQUEST_NOT_APPLICABLE; |
| } |
| |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| /* Send CMD2 ALL_SEND_CID */ |
| errorstate = SDMMC_CmdSendCID(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| else |
| { |
| /* Get Card identification number data */ |
| hsd->CID[0U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP1); |
| hsd->CID[1U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP2); |
| hsd->CID[2U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP3); |
| hsd->CID[3U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP4); |
| } |
| } |
| |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| /* Send CMD3 SET_REL_ADDR with argument 0 */ |
| /* SD Card publishes its RCA. */ |
| errorstate = SDMMC_CmdSetRelAdd(hsd->Instance, &sd_rca); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| } |
| if(hsd->SdCard.CardType != CARD_SECURED) |
| { |
| /* Get the SD card RCA */ |
| hsd->SdCard.RelCardAdd = sd_rca; |
| |
| /* Send CMD9 SEND_CSD with argument as card's RCA */ |
| errorstate = SDMMC_CmdSendCSD(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| else |
| { |
| /* Get Card Specific Data */ |
| hsd->CSD[0U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP1); |
| hsd->CSD[1U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP2); |
| hsd->CSD[2U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP3); |
| hsd->CSD[3U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP4); |
| } |
| } |
| |
| /* Get the Card Class */ |
| hsd->SdCard.Class = (SDIO_GetResponse(hsd->Instance, SDIO_RESP2) >> 20U); |
| |
| /* Get CSD parameters */ |
| if (HAL_SD_GetCardCSD(hsd, &CSD) != HAL_OK) |
| { |
| return HAL_SD_ERROR_UNSUPPORTED_FEATURE; |
| } |
| |
| /* Select the Card */ |
| errorstate = SDMMC_CmdSelDesel(hsd->Instance, (uint32_t)(((uint32_t)hsd->SdCard.RelCardAdd) << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* Configure SDIO peripheral interface */ |
| (void)SDIO_Init(hsd->Instance, hsd->Init); |
| |
| /* All cards are initialized */ |
| return HAL_SD_ERROR_NONE; |
| } |
| |
| /** |
| * @brief Enquires cards about their operating voltage and configures clock |
| * controls and stores SD information that will be needed in future |
| * in the SD handle. |
| * @param hsd: Pointer to SD handle |
| * @retval error state |
| */ |
| static uint32_t SD_PowerON(SD_HandleTypeDef *hsd) |
| { |
| __IO uint32_t count = 0U; |
| uint32_t response = 0U, validvoltage = 0U; |
| uint32_t errorstate; |
| |
| /* CMD0: GO_IDLE_STATE */ |
| errorstate = SDMMC_CmdGoIdleState(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* CMD8: SEND_IF_COND: Command available only on V2.0 cards */ |
| errorstate = SDMMC_CmdOperCond(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->SdCard.CardVersion = CARD_V1_X; |
| /* CMD0: GO_IDLE_STATE */ |
| errorstate = SDMMC_CmdGoIdleState(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| } |
| else |
| { |
| hsd->SdCard.CardVersion = CARD_V2_X; |
| } |
| |
| if( hsd->SdCard.CardVersion == CARD_V2_X) |
| { |
| /* SEND CMD55 APP_CMD with RCA as 0 */ |
| errorstate = SDMMC_CmdAppCommand(hsd->Instance, 0); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return HAL_SD_ERROR_UNSUPPORTED_FEATURE; |
| } |
| } |
| /* SD CARD */ |
| /* Send ACMD41 SD_APP_OP_COND with Argument 0x80100000 */ |
| while((count < SDMMC_MAX_VOLT_TRIAL) && (validvoltage == 0U)) |
| { |
| /* SEND CMD55 APP_CMD with RCA as 0 */ |
| errorstate = SDMMC_CmdAppCommand(hsd->Instance, 0); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* Send CMD41 */ |
| errorstate = SDMMC_CmdAppOperCommand(hsd->Instance, SDMMC_VOLTAGE_WINDOW_SD | SDMMC_HIGH_CAPACITY | SD_SWITCH_1_8V_CAPACITY); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return HAL_SD_ERROR_UNSUPPORTED_FEATURE; |
| } |
| |
| /* Get command response */ |
| response = SDIO_GetResponse(hsd->Instance, SDIO_RESP1); |
| |
| /* Get operating voltage*/ |
| validvoltage = (((response >> 31U) == 1U) ? 1U : 0U); |
| |
| count++; |
| } |
| |
| if(count >= SDMMC_MAX_VOLT_TRIAL) |
| { |
| return HAL_SD_ERROR_INVALID_VOLTRANGE; |
| } |
| |
| if((response & SDMMC_HIGH_CAPACITY) == SDMMC_HIGH_CAPACITY) /* (response &= SD_HIGH_CAPACITY) */ |
| { |
| hsd->SdCard.CardType = CARD_SDHC_SDXC; |
| } |
| else |
| { |
| hsd->SdCard.CardType = CARD_SDSC; |
| } |
| |
| |
| return HAL_SD_ERROR_NONE; |
| } |
| |
| /** |
| * @brief Turns the SDIO output signals off. |
| * @param hsd: Pointer to SD handle |
| * @retval None |
| */ |
| static void SD_PowerOFF(SD_HandleTypeDef *hsd) |
| { |
| /* Set Power State to OFF */ |
| (void)SDIO_PowerState_OFF(hsd->Instance); |
| } |
| |
| /** |
| * @brief Send Status info command. |
| * @param hsd: pointer to SD handle |
| * @param pSDstatus: Pointer to the buffer that will contain the SD card status |
| * SD Status register) |
| * @retval error state |
| */ |
| static uint32_t SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t tickstart = HAL_GetTick(); |
| uint32_t count; |
| uint32_t *pData = pSDstatus; |
| |
| /* Check SD response */ |
| if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED) |
| { |
| return HAL_SD_ERROR_LOCK_UNLOCK_FAILED; |
| } |
| |
| /* Set block size for card if it is not equal to current block size for card */ |
| errorstate = SDMMC_CmdBlockLength(hsd->Instance, 64U); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_NONE; |
| return errorstate; |
| } |
| |
| /* Send CMD55 */ |
| errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_NONE; |
| return errorstate; |
| } |
| |
| /* Configure the SD DPSM (Data Path State Machine) */ |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = 64U; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_64B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| /* Send ACMD13 (SD_APP_STAUS) with argument as card's RCA */ |
| errorstate = SDMMC_CmdStatusRegister(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| hsd->ErrorCode |= HAL_SD_ERROR_NONE; |
| return errorstate; |
| } |
| |
| /* Get status data */ |
| while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DBCKEND)) |
| { |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXFIFOHF)) |
| { |
| for(count = 0U; count < 8U; count++) |
| { |
| *pData = SDIO_ReadFIFO(hsd->Instance); |
| pData++; |
| } |
| } |
| |
| if((HAL_GetTick() - tickstart) >= SDMMC_DATATIMEOUT) |
| { |
| return HAL_SD_ERROR_TIMEOUT; |
| } |
| } |
| |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT)) |
| { |
| return HAL_SD_ERROR_DATA_TIMEOUT; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL)) |
| { |
| return HAL_SD_ERROR_DATA_CRC_FAIL; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR)) |
| { |
| return HAL_SD_ERROR_RX_OVERRUN; |
| } |
| else |
| { |
| /* Nothing to do */ |
| } |
| |
| while ((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXDAVL))) |
| { |
| *pData = SDIO_ReadFIFO(hsd->Instance); |
| pData++; |
| |
| if((HAL_GetTick() - tickstart) >= SDMMC_DATATIMEOUT) |
| { |
| return HAL_SD_ERROR_TIMEOUT; |
| } |
| } |
| |
| /* Clear all the static status flags*/ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| return HAL_SD_ERROR_NONE; |
| } |
| |
| /** |
| * @brief Returns the current card's status. |
| * @param hsd: Pointer to SD handle |
| * @param pCardStatus: pointer to the buffer that will contain the SD card |
| * status (Card Status register) |
| * @retval error state |
| */ |
| static uint32_t SD_SendStatus(SD_HandleTypeDef *hsd, uint32_t *pCardStatus) |
| { |
| uint32_t errorstate; |
| |
| if(pCardStatus == NULL) |
| { |
| return HAL_SD_ERROR_PARAM; |
| } |
| |
| /* Send Status command */ |
| errorstate = SDMMC_CmdSendStatus(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* Get SD card status */ |
| *pCardStatus = SDIO_GetResponse(hsd->Instance, SDIO_RESP1); |
| |
| return HAL_SD_ERROR_NONE; |
| } |
| |
| /** |
| * @brief Enables the SDIO wide bus mode. |
| * @param hsd: pointer to SD handle |
| * @retval error state |
| */ |
| static uint32_t SD_WideBus_Enable(SD_HandleTypeDef *hsd) |
| { |
| uint32_t scr[2U] = {0U, 0U}; |
| uint32_t errorstate; |
| |
| if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED) |
| { |
| return HAL_SD_ERROR_LOCK_UNLOCK_FAILED; |
| } |
| |
| /* Get SCR Register */ |
| errorstate = SD_FindSCR(hsd, scr); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* If requested card supports wide bus operation */ |
| if((scr[1U] & SDMMC_WIDE_BUS_SUPPORT) != SDMMC_ALLZERO) |
| { |
| /* Send CMD55 APP_CMD with argument as card's RCA.*/ |
| errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* Send ACMD6 APP_CMD with argument as 2 for wide bus mode */ |
| errorstate = SDMMC_CmdBusWidth(hsd->Instance, 2U); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| return HAL_SD_ERROR_NONE; |
| } |
| else |
| { |
| return HAL_SD_ERROR_REQUEST_NOT_APPLICABLE; |
| } |
| } |
| |
| /** |
| * @brief Disables the SDIO wide bus mode. |
| * @param hsd: Pointer to SD handle |
| * @retval error state |
| */ |
| static uint32_t SD_WideBus_Disable(SD_HandleTypeDef *hsd) |
| { |
| uint32_t scr[2U] = {0U, 0U}; |
| uint32_t errorstate; |
| |
| if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED) |
| { |
| return HAL_SD_ERROR_LOCK_UNLOCK_FAILED; |
| } |
| |
| /* Get SCR Register */ |
| errorstate = SD_FindSCR(hsd, scr); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* If requested card supports 1 bit mode operation */ |
| if((scr[1U] & SDMMC_SINGLE_BUS_SUPPORT) != SDMMC_ALLZERO) |
| { |
| /* Send CMD55 APP_CMD with argument as card's RCA */ |
| errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* Send ACMD6 APP_CMD with argument as 0 for single bus mode */ |
| errorstate = SDMMC_CmdBusWidth(hsd->Instance, 0U); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| return HAL_SD_ERROR_NONE; |
| } |
| else |
| { |
| return HAL_SD_ERROR_REQUEST_NOT_APPLICABLE; |
| } |
| } |
| |
| |
| /** |
| * @brief Finds the SD card SCR register value. |
| * @param hsd: Pointer to SD handle |
| * @param pSCR: pointer to the buffer that will contain the SCR value |
| * @retval error state |
| */ |
| static uint32_t SD_FindSCR(SD_HandleTypeDef *hsd, uint32_t *pSCR) |
| { |
| SDIO_DataInitTypeDef config; |
| uint32_t errorstate; |
| uint32_t tickstart = HAL_GetTick(); |
| uint32_t index = 0U; |
| uint32_t tempscr[2U] = {0U, 0U}; |
| uint32_t *scr = pSCR; |
| |
| /* Set Block Size To 8 Bytes */ |
| errorstate = SDMMC_CmdBlockLength(hsd->Instance, 8U); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| /* Send CMD55 APP_CMD with argument as card's RCA */ |
| errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)((hsd->SdCard.RelCardAdd) << 16U)); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| config.DataTimeOut = SDMMC_DATATIMEOUT; |
| config.DataLength = 8U; |
| config.DataBlockSize = SDIO_DATABLOCK_SIZE_8B; |
| config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; |
| config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; |
| config.DPSM = SDIO_DPSM_ENABLE; |
| (void)SDIO_ConfigData(hsd->Instance, &config); |
| |
| /* Send ACMD51 SD_APP_SEND_SCR with argument as 0 */ |
| errorstate = SDMMC_CmdSendSCR(hsd->Instance); |
| if(errorstate != HAL_SD_ERROR_NONE) |
| { |
| return errorstate; |
| } |
| |
| while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT)) |
| { |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXDAVL)) |
| { |
| *(tempscr + index) = SDIO_ReadFIFO(hsd->Instance); |
| index++; |
| } |
| else if(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXACT)) |
| { |
| break; |
| } |
| |
| if((HAL_GetTick() - tickstart) >= SDMMC_DATATIMEOUT) |
| { |
| return HAL_SD_ERROR_TIMEOUT; |
| } |
| } |
| |
| if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT)) |
| { |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_DTIMEOUT); |
| |
| return HAL_SD_ERROR_DATA_TIMEOUT; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL)) |
| { |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_DCRCFAIL); |
| |
| return HAL_SD_ERROR_DATA_CRC_FAIL; |
| } |
| else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR)) |
| { |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_RXOVERR); |
| |
| return HAL_SD_ERROR_RX_OVERRUN; |
| } |
| else |
| { |
| /* No error flag set */ |
| /* Clear all the static flags */ |
| __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS); |
| |
| *scr = (((tempscr[1] & SDMMC_0TO7BITS) << 24) | ((tempscr[1] & SDMMC_8TO15BITS) << 8) |\ |
| ((tempscr[1] & SDMMC_16TO23BITS) >> 8) | ((tempscr[1] & SDMMC_24TO31BITS) >> 24)); |
| scr++; |
| *scr = (((tempscr[0] & SDMMC_0TO7BITS) << 24) | ((tempscr[0] & SDMMC_8TO15BITS) << 8) |\ |
| ((tempscr[0] & SDMMC_16TO23BITS) >> 8) | ((tempscr[0] & SDMMC_24TO31BITS) >> 24)); |
| |
| } |
| |
| return HAL_SD_ERROR_NONE; |
| } |
| |
| /** |
| * @brief Wrap up reading in non-blocking mode. |
| * @param hsd: pointer to a SD_HandleTypeDef structure that contains |
| * the configuration information. |
| * @retval None |
| */ |
| static void SD_Read_IT(SD_HandleTypeDef *hsd) |
| { |
| uint32_t count, data, dataremaining; |
| uint8_t* tmp; |
| |
| tmp = hsd->pRxBuffPtr; |
| dataremaining = hsd->RxXferSize; |
| |
| if (dataremaining > 0U) |
| { |
| /* Read data from SDIO Rx FIFO */ |
| for(count = 0U; count < 8U; count++) |
| { |
| data = SDIO_ReadFIFO(hsd->Instance); |
| *tmp = (uint8_t)(data & 0xFFU); |
| tmp++; |
| dataremaining--; |
| *tmp = (uint8_t)((data >> 8U) & 0xFFU); |
| tmp++; |
| dataremaining--; |
| *tmp = (uint8_t)((data >> 16U) & 0xFFU); |
| tmp++; |
| dataremaining--; |
| *tmp = (uint8_t)((data >> 24U) & 0xFFU); |
| tmp++; |
| dataremaining--; |
| } |
| |
| hsd->pRxBuffPtr = tmp; |
| hsd->RxXferSize = dataremaining; |
| } |
| } |
| |
| /** |
| * @brief Wrap up writing in non-blocking mode. |
| * @param hsd: pointer to a SD_HandleTypeDef structure that contains |
| * the configuration information. |
| * @retval None |
| */ |
| static void SD_Write_IT(SD_HandleTypeDef *hsd) |
| { |
| uint32_t count, data, dataremaining; |
| |