/**
  ******************************************************************************
  * @file    stm32f4xx_hal_sd.h
  * @author  MCD Application Team
  * @brief   Header file of SD HAL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */ 

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_HAL_SD_H
#define __STM32F4xx_HAL_SD_H

#ifdef __cplusplus
 extern "C" {
#endif

#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
    defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
    defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
    defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \
    defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx)

/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_ll_sdmmc.h"

/** @addtogroup STM32F4xx_HAL_Driver
  * @{
  */

/** @defgroup SD SD
  * @brief SD HAL module driver
  * @{
  */ 

/* Exported types ------------------------------------------------------------*/ 
/** @defgroup SD_Exported_Types SD Exported Types
  * @{
  */

/** @defgroup SD_Exported_Types_Group1 SD State enumeration structure
  * @{
  */   
typedef enum
{
  HAL_SD_STATE_RESET                  = 0x00000000U,  /*!< SD not yet initialized or disabled  */
  HAL_SD_STATE_READY                  = 0x00000001U,  /*!< SD initialized and ready for use    */
  HAL_SD_STATE_TIMEOUT                = 0x00000002U,  /*!< SD Timeout state                    */
  HAL_SD_STATE_BUSY                   = 0x00000003U,  /*!< SD process ongoing                  */
  HAL_SD_STATE_PROGRAMMING            = 0x00000004U,  /*!< SD Programming State                */
  HAL_SD_STATE_RECEIVING              = 0x00000005U,  /*!< SD Receinving State                 */
  HAL_SD_STATE_TRANSFER               = 0x00000006U,  /*!< SD Transfert State                  */
  HAL_SD_STATE_ERROR                  = 0x0000000FU   /*!< SD is in error state                */
}HAL_SD_StateTypeDef;
/** 
  * @}
  */

/** @defgroup SD_Exported_Types_Group2 SD Card State enumeration structure
  * @{
  */   
typedef enum
{
  HAL_SD_CARD_READY                  = 0x00000001U,  /*!< Card state is ready                     */
  HAL_SD_CARD_IDENTIFICATION         = 0x00000002U,  /*!< Card is in identification state         */
  HAL_SD_CARD_STANDBY                = 0x00000003U,  /*!< Card is in standby state                */
  HAL_SD_CARD_TRANSFER               = 0x00000004U,  /*!< Card is in transfer state               */  
  HAL_SD_CARD_SENDING                = 0x00000005U,  /*!< Card is sending an operation            */
  HAL_SD_CARD_RECEIVING              = 0x00000006U,  /*!< Card is receiving operation information */
  HAL_SD_CARD_PROGRAMMING            = 0x00000007U,  /*!< Card is in programming state            */
  HAL_SD_CARD_DISCONNECTED           = 0x00000008U,  /*!< Card is disconnected                    */
  HAL_SD_CARD_ERROR                  = 0x000000FFU   /*!< Card response Error                     */
}HAL_SD_CardStateTypeDef;
/** 
  * @}
  */

/** @defgroup SD_Exported_Types_Group3 SD Handle Structure definition   
  * @{
  */
#define SD_InitTypeDef      SDIO_InitTypeDef 
#define SD_TypeDef          SDIO_TypeDef

/** 
  * @brief  SD Card Information Structure definition
  */ 
typedef struct
{
  uint32_t CardType;                     /*!< Specifies the card Type                         */
  
  uint32_t CardVersion;                  /*!< Specifies the card version                      */

  uint32_t Class;                        /*!< Specifies the class of the card class           */

  uint32_t RelCardAdd;                   /*!< Specifies the Relative Card Address             */
  
  uint32_t BlockNbr;                     /*!< Specifies the Card Capacity in blocks           */

  uint32_t BlockSize;                    /*!< Specifies one block size in bytes               */
  
  uint32_t LogBlockNbr;                  /*!< Specifies the Card logical Capacity in blocks   */

  uint32_t LogBlockSize;                 /*!< Specifies logical block size in bytes           */

}HAL_SD_CardInfoTypeDef;

/** 
  * @brief  SD handle Structure definition
  */ 
typedef struct __SD_HandleTypeDef
{
  SD_TypeDef                   *Instance;        /*!< SD registers base address           */
  
  SD_InitTypeDef               Init;             /*!< SD required parameters              */
  
  HAL_LockTypeDef              Lock;             /*!< SD locking object                   */
  
  uint32_t                     *pTxBuffPtr;      /*!< Pointer to SD Tx transfer Buffer    */

  uint32_t                     TxXferSize;       /*!< SD Tx Transfer size                 */

  uint32_t                     *pRxBuffPtr;      /*!< Pointer to SD Rx transfer Buffer    */

  uint32_t                     RxXferSize;       /*!< SD Rx Transfer size                 */
  
  __IO uint32_t                Context;          /*!< SD transfer context                 */
 
  __IO HAL_SD_StateTypeDef     State;            /*!< SD card State                       */
  
  __IO uint32_t                ErrorCode;        /*!< SD Card Error codes                 */  
 
  DMA_HandleTypeDef            *hdmarx;          /*!< SD Rx DMA handle parameters         */
  
  DMA_HandleTypeDef            *hdmatx;          /*!< SD Tx DMA handle parameters         */
  
  HAL_SD_CardInfoTypeDef       SdCard;           /*!< SD Card information                 */
  
  uint32_t                     CSD[4];           /*!< SD card specific data table         */
  
  uint32_t                     CID[4];           /*!< SD card identification number table */
  
#if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  void (* TxCpltCallback)                 (struct __SD_HandleTypeDef *hsd);
  void (* RxCpltCallback)                 (struct __SD_HandleTypeDef *hsd);
  void (* ErrorCallback)                  (struct __SD_HandleTypeDef *hsd);
  void (* AbortCpltCallback)              (struct __SD_HandleTypeDef *hsd);

  void (* MspInitCallback)                (struct __SD_HandleTypeDef *hsd);
  void (* MspDeInitCallback)              (struct __SD_HandleTypeDef *hsd);
#endif  
}SD_HandleTypeDef;

/** 
  * @}
  */

/** @defgroup SD_Exported_Types_Group4 Card Specific Data: CSD Register 
  * @{
  */
typedef struct
{
  __IO uint8_t  CSDStruct;            /*!< CSD structure                         */
  __IO uint8_t  SysSpecVersion;       /*!< System specification version          */
  __IO uint8_t  Reserved1;            /*!< Reserved                              */
  __IO uint8_t  TAAC;                 /*!< Data read access time 1               */
  __IO uint8_t  NSAC;                 /*!< Data read access time 2 in CLK cycles */
  __IO uint8_t  MaxBusClkFrec;        /*!< Max. bus clock frequency              */
  __IO uint16_t CardComdClasses;      /*!< Card command classes                  */
  __IO uint8_t  RdBlockLen;           /*!< Max. read data block length           */
  __IO uint8_t  PartBlockRead;        /*!< Partial blocks for read allowed       */
  __IO uint8_t  WrBlockMisalign;      /*!< Write block misalignment              */
  __IO uint8_t  RdBlockMisalign;      /*!< Read block misalignment               */
  __IO uint8_t  DSRImpl;              /*!< DSR implemented                       */
  __IO uint8_t  Reserved2;            /*!< Reserved                              */
  __IO uint32_t DeviceSize;           /*!< Device Size                           */
  __IO uint8_t  MaxRdCurrentVDDMin;   /*!< Max. read current @ VDD min           */
  __IO uint8_t  MaxRdCurrentVDDMax;   /*!< Max. read current @ VDD max           */
  __IO uint8_t  MaxWrCurrentVDDMin;   /*!< Max. write current @ VDD min          */
  __IO uint8_t  MaxWrCurrentVDDMax;   /*!< Max. write current @ VDD max          */
  __IO uint8_t  DeviceSizeMul;        /*!< Device size multiplier                */
  __IO uint8_t  EraseGrSize;          /*!< Erase group size                      */
  __IO uint8_t  EraseGrMul;           /*!< Erase group size multiplier           */
  __IO uint8_t  WrProtectGrSize;      /*!< Write protect group size              */
  __IO uint8_t  WrProtectGrEnable;    /*!< Write protect group enable            */
  __IO uint8_t  ManDeflECC;           /*!< Manufacturer default ECC              */
  __IO uint8_t  WrSpeedFact;          /*!< Write speed factor                    */
  __IO uint8_t  MaxWrBlockLen;        /*!< Max. write data block length          */
  __IO uint8_t  WriteBlockPaPartial;  /*!< Partial blocks for write allowed      */
  __IO uint8_t  Reserved3;            /*!< Reserved                              */
  __IO uint8_t  ContentProtectAppli;  /*!< Content protection application        */
  __IO uint8_t  FileFormatGrouop;     /*!< File format group                     */
  __IO uint8_t  CopyFlag;             /*!< Copy flag (OTP)                       */
  __IO uint8_t  PermWrProtect;        /*!< Permanent write protection            */
  __IO uint8_t  TempWrProtect;        /*!< Temporary write protection            */
  __IO uint8_t  FileFormat;           /*!< File format                           */
  __IO uint8_t  ECC;                  /*!< ECC code                              */
  __IO uint8_t  CSD_CRC;              /*!< CSD CRC                               */
  __IO uint8_t  Reserved4;            /*!< Always 1                              */
  
}HAL_SD_CardCSDTypeDef;
/** 
  * @}
  */

/** @defgroup SD_Exported_Types_Group5 Card Identification Data: CID Register
  * @{
  */
typedef struct
{
  __IO uint8_t  ManufacturerID;  /*!< Manufacturer ID       */
  __IO uint16_t OEM_AppliID;     /*!< OEM/Application ID    */
  __IO uint32_t ProdName1;       /*!< Product Name part1    */
  __IO uint8_t  ProdName2;       /*!< Product Name part2    */
  __IO uint8_t  ProdRev;         /*!< Product Revision      */
  __IO uint32_t ProdSN;          /*!< Product Serial Number */
  __IO uint8_t  Reserved1;       /*!< Reserved1             */
  __IO uint16_t ManufactDate;    /*!< Manufacturing Date    */
  __IO uint8_t  CID_CRC;         /*!< CID CRC               */
  __IO uint8_t  Reserved2;       /*!< Always 1              */

}HAL_SD_CardCIDTypeDef;
/** 
  * @}
  */

/** @defgroup SD_Exported_Types_Group6 SD Card Status returned by ACMD13 
  * @{
  */
typedef struct
{
  __IO uint8_t  DataBusWidth;           /*!< Shows the currently defined data bus width                 */
  __IO uint8_t  SecuredMode;            /*!< Card is in secured mode of operation                       */
  __IO uint16_t CardType;               /*!< Carries information about card type                        */
  __IO uint32_t ProtectedAreaSize;      /*!< Carries information about the capacity of protected area   */
  __IO uint8_t  SpeedClass;             /*!< Carries information about the speed class of the card      */
  __IO uint8_t  PerformanceMove;        /*!< Carries information about the card's performance move      */
  __IO uint8_t  AllocationUnitSize;     /*!< Carries information about the card's allocation unit size  */
  __IO uint16_t EraseSize;              /*!< Determines the number of AUs to be erased in one operation */
  __IO uint8_t  EraseTimeout;           /*!< Determines the timeout for any number of AU erase          */
  __IO uint8_t  EraseOffset;            /*!< Carries information about the erase offset                 */

}HAL_SD_CardStatusTypeDef;
/** 
  * @}
  */

#if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
/** @defgroup SD_Exported_Types_Group7 SD Callback ID enumeration definition 
  * @{
  */
typedef enum
{
  HAL_SD_TX_CPLT_CB_ID                 = 0x00U,  /*!< SD Tx Complete Callback ID                     */
  HAL_SD_RX_CPLT_CB_ID                 = 0x01U,  /*!< SD Rx Complete Callback ID                     */
  HAL_SD_ERROR_CB_ID                   = 0x02U,  /*!< SD Error Callback ID                           */
  HAL_SD_ABORT_CB_ID                   = 0x03U,  /*!< SD Abort Callback ID                           */

  HAL_SD_MSP_INIT_CB_ID                = 0x10U,  /*!< SD MspInit Callback ID                         */
  HAL_SD_MSP_DEINIT_CB_ID              = 0x11U   /*!< SD MspDeInit Callback ID                       */
}HAL_SD_CallbackIDTypeDef;
/** 
  * @}
  */

/** @defgroup SD_Exported_Types_Group8 SD Callback pointer definition 
  * @{
  */
typedef void (*pSD_CallbackTypeDef)           (SD_HandleTypeDef *hsd);
/** 
  * @}
  */
#endif
/** 
  * @}
  */

/* Exported constants --------------------------------------------------------*/
/** @defgroup SD_Exported_Constants Exported Constants
  * @{
  */

#define BLOCKSIZE   512U /*!< Block size is 512 bytes */

/** @defgroup SD_Exported_Constansts_Group1 SD Error status enumeration Structure definition 
  * @{
  */  
#define HAL_SD_ERROR_NONE                     SDMMC_ERROR_NONE                    /*!< No error                                                      */
#define HAL_SD_ERROR_CMD_CRC_FAIL             SDMMC_ERROR_CMD_CRC_FAIL            /*!< Command response received (but CRC check failed)              */
#define HAL_SD_ERROR_DATA_CRC_FAIL            SDMMC_ERROR_DATA_CRC_FAIL           /*!< Data block sent/received (CRC check failed)                   */
#define HAL_SD_ERROR_CMD_RSP_TIMEOUT          SDMMC_ERROR_CMD_RSP_TIMEOUT         /*!< Command response timeout                                      */
#define HAL_SD_ERROR_DATA_TIMEOUT             SDMMC_ERROR_DATA_TIMEOUT            /*!< Data timeout                                                  */
#define HAL_SD_ERROR_TX_UNDERRUN              SDMMC_ERROR_TX_UNDERRUN             /*!< Transmit FIFO underrun                                        */
#define HAL_SD_ERROR_RX_OVERRUN               SDMMC_ERROR_RX_OVERRUN              /*!< Receive FIFO overrun                                          */
#define HAL_SD_ERROR_ADDR_MISALIGNED          SDMMC_ERROR_ADDR_MISALIGNED         /*!< Misaligned address                                            */
#define HAL_SD_ERROR_BLOCK_LEN_ERR            SDMMC_ERROR_BLOCK_LEN_ERR           /*!< Transferred block length is not allowed for the card or the 
                                                                                       number of transferred bytes does not match the block length   */
#define HAL_SD_ERROR_ERASE_SEQ_ERR            SDMMC_ERROR_ERASE_SEQ_ERR           /*!< An error in the sequence of erase command occurs              */
#define HAL_SD_ERROR_BAD_ERASE_PARAM          SDMMC_ERROR_BAD_ERASE_PARAM         /*!< An invalid selection for erase groups                         */
#define HAL_SD_ERROR_WRITE_PROT_VIOLATION     SDMMC_ERROR_WRITE_PROT_VIOLATION    /*!< Attempt to program a write protect block                      */
#define HAL_SD_ERROR_LOCK_UNLOCK_FAILED       SDMMC_ERROR_LOCK_UNLOCK_FAILED      /*!< Sequence or password error has been detected in unlock 
                                                                                       command or if there was an attempt to access a locked card    */
#define HAL_SD_ERROR_COM_CRC_FAILED           SDMMC_ERROR_COM_CRC_FAILED          /*!< CRC check of the previous command failed                      */
#define HAL_SD_ERROR_ILLEGAL_CMD              SDMMC_ERROR_ILLEGAL_CMD             /*!< Command is not legal for the card state                       */
#define HAL_SD_ERROR_CARD_ECC_FAILED          SDMMC_ERROR_CARD_ECC_FAILED         /*!< Card internal ECC was applied but failed to correct the data  */
#define HAL_SD_ERROR_CC_ERR                   SDMMC_ERROR_CC_ERR                  /*!< Internal card controller error                                */
#define HAL_SD_ERROR_GENERAL_UNKNOWN_ERR      SDMMC_ERROR_GENERAL_UNKNOWN_ERR     /*!< General or unknown error                                      */
#define HAL_SD_ERROR_STREAM_READ_UNDERRUN     SDMMC_ERROR_STREAM_READ_UNDERRUN    /*!< The card could not sustain data reading in stream rmode       */
#define HAL_SD_ERROR_STREAM_WRITE_OVERRUN     SDMMC_ERROR_STREAM_WRITE_OVERRUN    /*!< The card could not sustain data programming in stream mode    */
#define HAL_SD_ERROR_CID_CSD_OVERWRITE        SDMMC_ERROR_CID_CSD_OVERWRITE       /*!< CID/CSD overwrite error                                       */
#define HAL_SD_ERROR_WP_ERASE_SKIP            SDMMC_ERROR_WP_ERASE_SKIP           /*!< Only partial address space was erased                         */
#define HAL_SD_ERROR_CARD_ECC_DISABLED        SDMMC_ERROR_CARD_ECC_DISABLED       /*!< Command has been executed without using internal ECC          */
#define HAL_SD_ERROR_ERASE_RESET              SDMMC_ERROR_ERASE_RESET             /*!< Erase sequence was cleared before executing because an out 
                                                                                       of erase sequence command was received                        */
#define HAL_SD_ERROR_AKE_SEQ_ERR              SDMMC_ERROR_AKE_SEQ_ERR             /*!< Error in sequence of authentication                           */
#define HAL_SD_ERROR_INVALID_VOLTRANGE        SDMMC_ERROR_INVALID_VOLTRANGE       /*!< Error in case of invalid voltage range                        */        
#define HAL_SD_ERROR_ADDR_OUT_OF_RANGE        SDMMC_ERROR_ADDR_OUT_OF_RANGE       /*!< Error when addressed block is out of range                    */        
#define HAL_SD_ERROR_REQUEST_NOT_APPLICABLE   SDMMC_ERROR_REQUEST_NOT_APPLICABLE  /*!< Error when command request is not applicable                  */  
#define HAL_SD_ERROR_PARAM                    SDMMC_ERROR_INVALID_PARAMETER       /*!< the used parameter is not valid                               */  
#define HAL_SD_ERROR_UNSUPPORTED_FEATURE      SDMMC_ERROR_UNSUPPORTED_FEATURE     /*!< Error when feature is not insupported                         */
#define HAL_SD_ERROR_BUSY                     SDMMC_ERROR_BUSY                    /*!< Error when transfer process is busy                           */ 
#define HAL_SD_ERROR_DMA                      SDMMC_ERROR_DMA                     /*!< Error while DMA transfer                                      */
#define HAL_SD_ERROR_TIMEOUT                  SDMMC_ERROR_TIMEOUT                 /*!< Timeout error                                                 */
                                                
#if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
#define HAL_SD_ERROR_INVALID_CALLBACK         SDMMC_ERROR_INVALID_PARAMETER       /*!< Invalid callback error                                        */
#endif
                                                
/** 
  * @}
  */
 
/** @defgroup SD_Exported_Constansts_Group2 SD context enumeration
  * @{
  */ 
#define   SD_CONTEXT_NONE                 0x00000000U  /*!< None                             */
#define   SD_CONTEXT_READ_SINGLE_BLOCK    0x00000001U  /*!< Read single block operation      */
#define   SD_CONTEXT_READ_MULTIPLE_BLOCK  0x00000002U  /*!< Read multiple blocks operation   */
#define   SD_CONTEXT_WRITE_SINGLE_BLOCK   0x00000010U  /*!< Write single block operation     */
#define   SD_CONTEXT_WRITE_MULTIPLE_BLOCK 0x00000020U  /*!< Write multiple blocks operation  */
#define   SD_CONTEXT_IT                   0x00000008U  /*!< Process in Interrupt mode        */
#define   SD_CONTEXT_DMA                  0x00000080U  /*!< Process in DMA mode              */  

/**
  * @}
  */

/** @defgroup SD_Exported_Constansts_Group3 SD Supported Memory Cards
  * @{
  */
#define CARD_SDSC                  0x00000000U
#define CARD_SDHC_SDXC             0x00000001U
#define CARD_SECURED               0x00000003U
    
/**
  * @}
  */

/** @defgroup SD_Exported_Constansts_Group4 SD Supported Version
  * @{
  */
#define CARD_V1_X                  0x00000000U
#define CARD_V2_X                  0x00000001U
/**
  * @}
  */
      
/**
  * @}
  */
  
/* Exported macro ------------------------------------------------------------*/
/** @defgroup SD_Exported_macros SD Exported Macros
 *  @brief macros to handle interrupts and specific clock configurations
 * @{
 */
/** @brief Reset SD handle state.
  * @param  __HANDLE__ : SD handle.
  * @retval None
  */
#if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
#define __HAL_SD_RESET_HANDLE_STATE(__HANDLE__)           do {                                              \
                                                               (__HANDLE__)->State = HAL_SD_STATE_RESET; \
                                                               (__HANDLE__)->MspInitCallback = NULL;       \
                                                               (__HANDLE__)->MspDeInitCallback = NULL;     \
                                                             } while(0)
#else
#define __HAL_SD_RESET_HANDLE_STATE(__HANDLE__)           ((__HANDLE__)->State = HAL_SD_STATE_RESET)
#endif
 
/**
  * @brief  Enable the SD device.
  * @retval None
  */ 
#define __HAL_SD_ENABLE(__HANDLE__) __SDIO_ENABLE((__HANDLE__)->Instance)

/**
  * @brief  Disable the SD device.
  * @retval None
  */
#define __HAL_SD_DISABLE(__HANDLE__) __SDIO_DISABLE((__HANDLE__)->Instance)

/**
  * @brief  Enable the SDMMC DMA transfer.
  * @retval None
  */ 
#define __HAL_SD_DMA_ENABLE(__HANDLE__) __SDIO_DMA_ENABLE((__HANDLE__)->Instance)

/**
  * @brief  Disable the SDMMC DMA transfer.
  * @retval None
  */
#define __HAL_SD_DMA_DISABLE(__HANDLE__)  __SDIO_DMA_DISABLE((__HANDLE__)->Instance)
 
/**
  * @brief  Enable the SD device interrupt.
  * @param  __HANDLE__ SD Handle  
  * @param  __INTERRUPT__ specifies the SDMMC interrupt sources to be enabled.
  *         This parameter can be one or a combination of the following values:
  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
  *            @arg SDIO_IT_DATAEND:  Data end (data counter, SDIDCOUNT, is zero) interrupt
  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt
  * @retval None
  */
#define __HAL_SD_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))

/**
  * @brief  Disable the SD device interrupt.
  * @param  __HANDLE__ SD Handle   
  * @param  __INTERRUPT__ specifies the SDMMC interrupt sources to be disabled.
  *          This parameter can be one or a combination of the following values:
  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
  *            @arg SDIO_IT_DATAEND:  Data end (data counter, SDIDCOUNT, is zero) interrupt
  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt   
  * @retval None
  */
#define __HAL_SD_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))

/**
  * @brief  Check whether the specified SD flag is set or not. 
  * @param  __HANDLE__ SD Handle   
  * @param  __FLAG__ specifies the flag to check. 
  *          This parameter can be one of the following values:
  *            @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
  *            @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
  *            @arg SDIO_FLAG_CTIMEOUT: Command response timeout
  *            @arg SDIO_FLAG_DTIMEOUT: Data timeout
  *            @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
  *            @arg SDIO_FLAG_RXOVERR:  Received FIFO overrun error
  *            @arg SDIO_FLAG_CMDREND:  Command response received (CRC check passed)
  *            @arg SDIO_FLAG_CMDSENT:  Command sent (no response required)
  *            @arg SDIO_FLAG_DATAEND:  Data end (data counter, SDIDCOUNT, is zero)
  *            @arg SDIO_FLAG_DBCKEND:  Data block sent/received (CRC check passed)
  *            @arg SDIO_FLAG_CMDACT:   Command transfer in progress
  *            @arg SDIO_FLAG_TXACT:    Data transmit in progress
  *            @arg SDIO_FLAG_RXACT:    Data receive in progress
  *            @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty
  *            @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full
  *            @arg SDIO_FLAG_TXFIFOF:  Transmit FIFO full
  *            @arg SDIO_FLAG_RXFIFOF:  Receive FIFO full
  *            @arg SDIO_FLAG_TXFIFOE:  Transmit FIFO empty
  *            @arg SDIO_FLAG_RXFIFOE:  Receive FIFO empty
  *            @arg SDIO_FLAG_TXDAVL:   Data available in transmit FIFO
  *            @arg SDIO_FLAG_RXDAVL:   Data available in receive FIFO
  *            @arg SDIO_FLAG_SDIOIT:   SD I/O interrupt received
  * @retval The new state of SD FLAG (SET or RESET).
  */
#define __HAL_SD_GET_FLAG(__HANDLE__, __FLAG__) __SDIO_GET_FLAG((__HANDLE__)->Instance, (__FLAG__))

/**
  * @brief  Clear the SD's pending flags.
  * @param  __HANDLE__ SD Handle  
  * @param  __FLAG__ specifies the flag to clear.  
  *          This parameter can be one or a combination of the following values:
  *            @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
  *            @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
  *            @arg SDIO_FLAG_CTIMEOUT: Command response timeout
  *            @arg SDIO_FLAG_DTIMEOUT: Data timeout
  *            @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
  *            @arg SDIO_FLAG_RXOVERR:  Received FIFO overrun error
  *            @arg SDIO_FLAG_CMDREND:  Command response received (CRC check passed)
  *            @arg SDIO_FLAG_CMDSENT:  Command sent (no response required)
  *            @arg SDIO_FLAG_DATAEND:  Data end (data counter, SDIDCOUNT, is zero)
  *            @arg SDIO_FLAG_DBCKEND:  Data block sent/received (CRC check passed)
  *            @arg SDIO_FLAG_SDIOIT:   SD I/O interrupt received
  * @retval None
  */
#define __HAL_SD_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDIO_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__))

/**
  * @brief  Check whether the specified SD interrupt has occurred or not.
  * @param  __HANDLE__ SD Handle   
  * @param  __INTERRUPT__ specifies the SDMMC interrupt source to check. 
  *          This parameter can be one of the following values:
  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
  *            @arg SDIO_IT_DATAEND:  Data end (data counter, SDIDCOUNT, is zero) interrupt
  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt
  * @retval The new state of SD IT (SET or RESET).
  */
#define __HAL_SD_GET_IT(__HANDLE__, __INTERRUPT__) __SDIO_GET_IT((__HANDLE__)->Instance, (__INTERRUPT__))

/**
  * @brief  Clear the SD's interrupt pending bits.
  * @param  __HANDLE__ SD Handle
  * @param  __INTERRUPT__ specifies the interrupt pending bit to clear. 
  *          This parameter can be one or a combination of the following values:
  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
  *            @arg SDIO_IT_DATAEND:  Data end (data counter, SDMMC_DCOUNT, is zero) interrupt
  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt
  * @retval None
  */
#define __HAL_SD_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDIO_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__))

/**
  * @}
  */
  
/* Exported functions --------------------------------------------------------*/
/** @defgroup SD_Exported_Functions SD Exported Functions
  * @{
  */
  
/** @defgroup SD_Exported_Functions_Group1 Initialization and de-initialization functions
  * @{
  */
HAL_StatusTypeDef HAL_SD_Init(SD_HandleTypeDef *hsd);
HAL_StatusTypeDef HAL_SD_InitCard(SD_HandleTypeDef *hsd);
HAL_StatusTypeDef HAL_SD_DeInit (SD_HandleTypeDef *hsd);
void HAL_SD_MspInit(SD_HandleTypeDef *hsd);
void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd);
/**
  * @}
  */
  
/** @defgroup SD_Exported_Functions_Group2 Input and Output operation functions
  * @{
  */
/* Blocking mode: Polling */
HAL_StatusTypeDef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout);
HAL_StatusTypeDef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout);
HAL_StatusTypeDef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint32_t BlockStartAdd, uint32_t BlockEndAdd);
/* Non-Blocking mode: IT */
HAL_StatusTypeDef HAL_SD_ReadBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
HAL_StatusTypeDef HAL_SD_WriteBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
/* Non-Blocking mode: DMA */
HAL_StatusTypeDef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
HAL_StatusTypeDef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);

void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd);

/* Callback in non blocking modes (DMA) */
void HAL_SD_TxCpltCallback(SD_HandleTypeDef *hsd);
void HAL_SD_RxCpltCallback(SD_HandleTypeDef *hsd);
void HAL_SD_ErrorCallback(SD_HandleTypeDef *hsd);
void HAL_SD_AbortCallback(SD_HandleTypeDef *hsd);

#if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
/* SD callback registering/unregistering */
HAL_StatusTypeDef HAL_SD_RegisterCallback  (SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackId, pSD_CallbackTypeDef pCallback);
HAL_StatusTypeDef HAL_SD_UnRegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackId);
#endif
/**
  * @}
  */
  
/** @defgroup SD_Exported_Functions_Group3 Peripheral Control functions
  * @{
  */
HAL_StatusTypeDef HAL_SD_ConfigWideBusOperation(SD_HandleTypeDef *hsd, uint32_t WideMode);
/**
  * @}
  */

/** @defgroup SD_Exported_Functions_Group4 SD card related functions
  * @{
  */
HAL_StatusTypeDef       HAL_SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus);
HAL_SD_CardStateTypeDef HAL_SD_GetCardState(SD_HandleTypeDef *hsd);
HAL_StatusTypeDef       HAL_SD_GetCardCID(SD_HandleTypeDef *hsd, HAL_SD_CardCIDTypeDef *pCID);
HAL_StatusTypeDef       HAL_SD_GetCardCSD(SD_HandleTypeDef *hsd, HAL_SD_CardCSDTypeDef *pCSD);
HAL_StatusTypeDef       HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypeDef *pStatus);
HAL_StatusTypeDef       HAL_SD_GetCardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypeDef *pCardInfo);
/**
  * @}
  */

/** @defgroup SD_Exported_Functions_Group5 Peripheral State and Errors functions
  * @{
  */
HAL_SD_StateTypeDef HAL_SD_GetState(SD_HandleTypeDef *hsd);
uint32_t HAL_SD_GetError(SD_HandleTypeDef *hsd);
/**
  * @}
  */

/** @defgroup SD_Exported_Functions_Group6 Perioheral Abort management
  * @{
  */
HAL_StatusTypeDef HAL_SD_Abort(SD_HandleTypeDef *hsd);
HAL_StatusTypeDef HAL_SD_Abort_IT(SD_HandleTypeDef *hsd);
/**
  * @}
  */
    
/* Private types -------------------------------------------------------------*/
/** @defgroup SD_Private_Types SD Private Types
  * @{
  */

/**
  * @}
  */ 

/* Private defines -----------------------------------------------------------*/
/** @defgroup SD_Private_Defines SD Private Defines
  * @{
  */

/**
  * @}
  */ 
          
/* Private variables ---------------------------------------------------------*/
/** @defgroup SD_Private_Variables SD Private Variables
  * @{
  */

/**
  * @}
  */ 

/* Private constants ---------------------------------------------------------*/
/** @defgroup SD_Private_Constants SD Private Constants
  * @{
  */

/**
  * @}
  */ 

/* Private macros ------------------------------------------------------------*/
/** @defgroup SD_Private_Macros SD Private Macros
  * @{
  */

/**
  * @}
  */

/* Private functions prototypes ----------------------------------------------*/
/** @defgroup SD_Private_Functions_Prototypes SD Private Functions Prototypes
  * @{
  */

/**
  * @}
  */

/* Private functions ---------------------------------------------------------*/
/** @defgroup SD_Private_Functions SD Private Functions
  * @{
  */

/**
  * @}
  */


/**
  * @}
  */ 

/**
  * @}
  */

/**
  * @}
  */

#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
          STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx ||
          STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */

#ifdef __cplusplus
}
#endif


#endif /* __STM32F4xx_HAL_SD_H */ 

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/