/**
  ******************************************************************************
  * @file    stm32f7xx_hal_irda.h
  * @author  MCD Application Team
  * @brief   Header file of IRDA HAL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32F7xx_HAL_IRDA_H
#define STM32F7xx_HAL_IRDA_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32f7xx_hal_def.h"

/** @addtogroup STM32F7xx_HAL_Driver
  * @{
  */

/** @addtogroup IRDA
  * @{
  */

/* Exported types ------------------------------------------------------------*/
/** @defgroup IRDA_Exported_Types IRDA Exported Types
  * @{
  */

/**
  * @brief IRDA Init Structure definition
  */
typedef struct
{
  uint32_t BaudRate;                  /*!< This member configures the IRDA communication baud rate.
                                           The baud rate register is computed using the following formula:
                                              Baud Rate Register = ((usart_ker_clk) / ((hirda->Init.BaudRate)))
                                           where usart_ker_clk is the IRDA input clock */

  uint32_t WordLength;                /*!< Specifies the number of data bits transmitted or received in a frame.
                                           This parameter can be a value of @ref IRDAEx_Word_Length */

  uint32_t Parity;                    /*!< Specifies the parity mode.
                                           This parameter can be a value of @ref IRDA_Parity
                                           @note When parity is enabled, the computed parity is inserted
                                                 at the MSB position of the transmitted data (9th bit when
                                                 the word length is set to 9 data bits; 8th bit when the
                                                 word length is set to 8 data bits). */

  uint32_t Mode;                      /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
                                           This parameter can be a value of @ref IRDA_Transfer_Mode */

  uint8_t  Prescaler;                 /*!< Specifies the Prescaler value for dividing the UART/USART source clock
                                           to achieve low-power frequency.
                                           @note Prescaler value 0 is forbidden */

  uint16_t PowerMode;                 /*!< Specifies the IRDA power mode.
                                           This parameter can be a value of @ref IRDA_Low_Power */

} IRDA_InitTypeDef;

/**
  * @brief HAL IRDA State definition
  * @note  HAL IRDA State value is a combination of 2 different substates: gState and RxState (see @ref IRDA_State_Definition).
  *        - gState contains IRDA state information related to global Handle management
  *          and also information related to Tx operations.
  *          gState value coding follow below described bitmap :
  *          b7-b6  Error information
  *             00 : No Error
  *             01 : (Not Used)
  *             10 : Timeout
  *             11 : Error
  *          b5     Peripheral initialization status
  *             0  : Reset (Peripheral not initialized)
  *             1  : Init done (Peripheral not initialized. HAL IRDA Init function already called)
  *          b4-b3  (not used)
  *             xx : Should be set to 00
  *          b2     Intrinsic process state
  *             0  : Ready
  *             1  : Busy (Peripheral busy with some configuration or internal operations)
  *          b1     (not used)
  *             x  : Should be set to 0
  *          b0     Tx state
  *             0  : Ready (no Tx operation ongoing)
  *             1  : Busy (Tx operation ongoing)
  *        - RxState contains information related to Rx operations.
  *          RxState value coding follow below described bitmap :
  *          b7-b6  (not used)
  *             xx : Should be set to 00
  *          b5     Peripheral initialization status
  *             0  : Reset (Peripheral not initialized)
  *             1  : Init done (Peripheral not initialized)
  *          b4-b2  (not used)
  *            xxx : Should be set to 000
  *          b1     Rx state
  *             0  : Ready (no Rx operation ongoing)
  *             1  : Busy (Rx operation ongoing)
  *          b0     (not used)
  *             x  : Should be set to 0.
  */
typedef uint32_t HAL_IRDA_StateTypeDef;

/**
  * @brief IRDA clock sources definition
  */
typedef enum
{
  IRDA_CLOCKSOURCE_PCLK1      = 0x00U,    /*!< PCLK1 clock source         */
  IRDA_CLOCKSOURCE_PCLK2      = 0x01U,    /*!< PCLK2 clock source         */
  IRDA_CLOCKSOURCE_HSI        = 0x02U,    /*!< HSI clock source           */
  IRDA_CLOCKSOURCE_SYSCLK     = 0x04U,    /*!< SYSCLK clock source        */
  IRDA_CLOCKSOURCE_LSE        = 0x10U,    /*!< LSE clock source           */
  IRDA_CLOCKSOURCE_UNDEFINED  = 0x20U     /*!< Undefined clock source     */
} IRDA_ClockSourceTypeDef;

/**
  * @brief  IRDA handle Structure definition
  */
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
typedef struct __IRDA_HandleTypeDef
#else
typedef struct
#endif  /* USE_HAL_IRDA_REGISTER_CALLBACKS */
{
  USART_TypeDef            *Instance;        /*!< USART registers base address       */

  IRDA_InitTypeDef         Init;             /*!< IRDA communication parameters      */

  uint8_t                  *pTxBuffPtr;      /*!< Pointer to IRDA Tx transfer Buffer */

  uint16_t                 TxXferSize;       /*!< IRDA Tx Transfer size              */

  __IO uint16_t            TxXferCount;      /*!< IRDA Tx Transfer Counter           */

  uint8_t                  *pRxBuffPtr;      /*!< Pointer to IRDA Rx transfer Buffer */

  uint16_t                 RxXferSize;       /*!< IRDA Rx Transfer size              */

  __IO uint16_t            RxXferCount;      /*!< IRDA Rx Transfer Counter           */

  uint16_t                 Mask;             /*!< USART RX RDR register mask         */

  DMA_HandleTypeDef        *hdmatx;          /*!< IRDA Tx DMA Handle parameters      */

  DMA_HandleTypeDef        *hdmarx;          /*!< IRDA Rx DMA Handle parameters      */

  HAL_LockTypeDef          Lock;             /*!< Locking object                     */

  __IO HAL_IRDA_StateTypeDef    gState;      /*!< IRDA state information related to global Handle management
                                                  and also related to Tx operations.
                                                  This parameter can be a value of @ref HAL_IRDA_StateTypeDef */

  __IO HAL_IRDA_StateTypeDef    RxState;     /*!< IRDA state information related to Rx operations.
                                                  This parameter can be a value of @ref HAL_IRDA_StateTypeDef */

  __IO uint32_t            ErrorCode;        /*!< IRDA Error code                    */

#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
  void (* TxHalfCpltCallback)(struct __IRDA_HandleTypeDef *hirda);        /*!< IRDA Tx Half Complete Callback        */

  void (* TxCpltCallback)(struct __IRDA_HandleTypeDef *hirda);            /*!< IRDA Tx Complete Callback             */

  void (* RxHalfCpltCallback)(struct __IRDA_HandleTypeDef *hirda);        /*!< IRDA Rx Half Complete Callback        */

  void (* RxCpltCallback)(struct __IRDA_HandleTypeDef *hirda);            /*!< IRDA Rx Complete Callback             */

  void (* ErrorCallback)(struct __IRDA_HandleTypeDef *hirda);             /*!< IRDA Error Callback                   */

  void (* AbortCpltCallback)(struct __IRDA_HandleTypeDef *hirda);         /*!< IRDA Abort Complete Callback          */

  void (* AbortTransmitCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Abort Transmit Complete Callback */

  void (* AbortReceiveCpltCallback)(struct __IRDA_HandleTypeDef *hirda);  /*!< IRDA Abort Receive Complete Callback  */


  void (* MspInitCallback)(struct __IRDA_HandleTypeDef *hirda);           /*!< IRDA Msp Init callback                */

  void (* MspDeInitCallback)(struct __IRDA_HandleTypeDef *hirda);         /*!< IRDA Msp DeInit callback              */
#endif  /* USE_HAL_IRDA_REGISTER_CALLBACKS */

} IRDA_HandleTypeDef;

#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
/**
  * @brief  HAL IRDA Callback ID enumeration definition
  */
typedef enum
{
  HAL_IRDA_TX_HALFCOMPLETE_CB_ID         = 0x00U,    /*!< IRDA Tx Half Complete Callback ID        */
  HAL_IRDA_TX_COMPLETE_CB_ID             = 0x01U,    /*!< IRDA Tx Complete Callback ID             */
  HAL_IRDA_RX_HALFCOMPLETE_CB_ID         = 0x02U,    /*!< IRDA Rx Half Complete Callback ID        */
  HAL_IRDA_RX_COMPLETE_CB_ID             = 0x03U,    /*!< IRDA Rx Complete Callback ID             */
  HAL_IRDA_ERROR_CB_ID                   = 0x04U,    /*!< IRDA Error Callback ID                   */
  HAL_IRDA_ABORT_COMPLETE_CB_ID          = 0x05U,    /*!< IRDA Abort Complete Callback ID          */
  HAL_IRDA_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x06U,    /*!< IRDA Abort Transmit Complete Callback ID */
  HAL_IRDA_ABORT_RECEIVE_COMPLETE_CB_ID  = 0x07U,    /*!< IRDA Abort Receive Complete Callback ID  */

  HAL_IRDA_MSPINIT_CB_ID                 = 0x08U,    /*!< IRDA MspInit callback ID                 */
  HAL_IRDA_MSPDEINIT_CB_ID               = 0x09U     /*!< IRDA MspDeInit callback ID               */

} HAL_IRDA_CallbackIDTypeDef;

/**
  * @brief  HAL IRDA Callback pointer definition
  */
typedef  void (*pIRDA_CallbackTypeDef)(IRDA_HandleTypeDef *hirda);  /*!< pointer to an IRDA callback function */

#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */

/**
  * @}
  */

/* Exported constants --------------------------------------------------------*/
/** @defgroup IRDA_Exported_Constants IRDA Exported Constants
  * @{
  */

/** @defgroup IRDA_State_Definition IRDA State Code Definition
  * @{
  */
#define HAL_IRDA_STATE_RESET                0x00000000U   /*!< Peripheral is not initialized
                                                               Value is allowed for gState and RxState */
#define HAL_IRDA_STATE_READY                0x00000020U   /*!< Peripheral Initialized and ready for use
                                                               Value is allowed for gState and RxState */
#define HAL_IRDA_STATE_BUSY                 0x00000024U   /*!< An internal process is ongoing
                                                               Value is allowed for gState only */
#define HAL_IRDA_STATE_BUSY_TX              0x00000021U   /*!< Data Transmission process is ongoing
                                                               Value is allowed for gState only */
#define HAL_IRDA_STATE_BUSY_RX              0x00000022U   /*!< Data Reception process is ongoing
                                                               Value is allowed for RxState only */
#define HAL_IRDA_STATE_BUSY_TX_RX           0x00000023U   /*!< Data Transmission and Reception process is ongoing
                                                               Not to be used for neither gState nor RxState.
                                                               Value is result of combination (Or) between gState and RxState values */
#define HAL_IRDA_STATE_TIMEOUT              0x000000A0U   /*!< Timeout state
                                                               Value is allowed for gState only */
#define HAL_IRDA_STATE_ERROR                0x000000E0U   /*!< Error
                                                               Value is allowed for gState only */
/**
  * @}
  */

/** @defgroup IRDA_Error_Definition IRDA Error Code Definition
  * @{
  */
#define HAL_IRDA_ERROR_NONE                 ((uint32_t)0x00000000U)          /*!< No error                */
#define HAL_IRDA_ERROR_PE                   ((uint32_t)0x00000001U)          /*!< Parity error            */
#define HAL_IRDA_ERROR_NE                   ((uint32_t)0x00000002U)          /*!< Noise error             */
#define HAL_IRDA_ERROR_FE                   ((uint32_t)0x00000004U)          /*!< frame error             */
#define HAL_IRDA_ERROR_ORE                  ((uint32_t)0x00000008U)          /*!< Overrun error           */
#define HAL_IRDA_ERROR_DMA                  ((uint32_t)0x00000010U)          /*!< DMA transfer error      */
#define HAL_IRDA_ERROR_BUSY                 ((uint32_t)0x00000020U)          /*!< Busy Error              */
#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
#define HAL_IRDA_ERROR_INVALID_CALLBACK     ((uint32_t)0x00000040U)          /*!< Invalid Callback error  */
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
/**
  * @}
  */

/** @defgroup IRDA_Parity IRDA Parity
  * @{
  */
#define IRDA_PARITY_NONE                    0x00000000U                      /*!< No parity   */
#define IRDA_PARITY_EVEN                    USART_CR1_PCE                    /*!< Even parity */
#define IRDA_PARITY_ODD                     (USART_CR1_PCE | USART_CR1_PS)   /*!< Odd parity  */
/**
  * @}
  */

/** @defgroup IRDA_Transfer_Mode IRDA Transfer Mode
  * @{
  */
#define IRDA_MODE_RX                        USART_CR1_RE                   /*!< RX mode        */
#define IRDA_MODE_TX                        USART_CR1_TE                   /*!< TX mode        */
#define IRDA_MODE_TX_RX                     (USART_CR1_TE |USART_CR1_RE)   /*!< RX and TX mode */
/**
  * @}
  */

/** @defgroup IRDA_Low_Power IRDA Low Power
  * @{
  */
#define IRDA_POWERMODE_NORMAL               0x00000000U       /*!< IRDA normal power mode */
#define IRDA_POWERMODE_LOWPOWER             USART_CR3_IRLP    /*!< IRDA low power mode    */
/**
  * @}
  */

/** @defgroup IRDA_State IRDA State
  * @{
  */
#define IRDA_STATE_DISABLE                  0x00000000U     /*!< IRDA disabled  */
#define IRDA_STATE_ENABLE                   USART_CR1_UE    /*!< IRDA enabled   */
/**
  * @}
  */

/** @defgroup IRDA_Mode IRDA Mode
  * @{
  */
#define IRDA_MODE_DISABLE                   0x00000000U      /*!< Associated UART disabled in IRDA mode */
#define IRDA_MODE_ENABLE                    USART_CR3_IREN   /*!< Associated UART enabled in IRDA mode  */
/**
  * @}
  */

/** @defgroup IRDA_One_Bit IRDA One Bit Sampling
  * @{
  */
#define IRDA_ONE_BIT_SAMPLE_DISABLE         0x00000000U       /*!< One-bit sampling disabled */
#define IRDA_ONE_BIT_SAMPLE_ENABLE          USART_CR3_ONEBIT  /*!< One-bit sampling enabled  */
/**
  * @}
  */

/** @defgroup IRDA_DMA_Tx IRDA DMA Tx
  * @{
  */
#define IRDA_DMA_TX_DISABLE                 0x00000000U       /*!< IRDA DMA TX disabled */
#define IRDA_DMA_TX_ENABLE                  USART_CR3_DMAT    /*!< IRDA DMA TX enabled  */
/**
  * @}
  */

/** @defgroup IRDA_DMA_Rx IRDA DMA Rx
  * @{
  */
#define IRDA_DMA_RX_DISABLE                 0x00000000U       /*!< IRDA DMA RX disabled */
#define IRDA_DMA_RX_ENABLE                  USART_CR3_DMAR    /*!< IRDA DMA RX enabled  */
/**
  * @}
  */

/** @defgroup IRDA_Request_Parameters IRDA Request Parameters
  * @{
  */
#define IRDA_AUTOBAUD_REQUEST            USART_RQR_ABRRQ        /*!< Auto-Baud Rate Request      */
#define IRDA_RXDATA_FLUSH_REQUEST        USART_RQR_RXFRQ        /*!< Receive Data flush Request  */
#define IRDA_TXDATA_FLUSH_REQUEST        USART_RQR_TXFRQ        /*!< Transmit data flush Request */
/**
  * @}
  */

/** @defgroup IRDA_Flags IRDA Flags
  *        Elements values convention: 0xXXXX
  *           - 0xXXXX  : Flag mask in the ISR register
  * @{
  */
#define IRDA_FLAG_TEACK                     USART_ISR_TEACK         /*!< IRDA transmit enable acknowledge flag     */
#define IRDA_FLAG_BUSY                      USART_ISR_BUSY          /*!< IRDA busy flag                            */
#define IRDA_FLAG_ABRF                      USART_ISR_ABRF          /*!< IRDA auto Baud rate flag                  */
#define IRDA_FLAG_ABRE                      USART_ISR_ABRE          /*!< IRDA auto Baud rate error                 */
#define IRDA_FLAG_TXE                       USART_ISR_TXE           /*!< IRDA transmit data register empty         */
#define IRDA_FLAG_TC                        USART_ISR_TC            /*!< IRDA transmission complete                */
#define IRDA_FLAG_RXNE                      USART_ISR_RXNE          /*!< IRDA read data register not empty         */
#define IRDA_FLAG_ORE                       USART_ISR_ORE           /*!< IRDA overrun error                        */
#define IRDA_FLAG_NE                        USART_ISR_NE            /*!< IRDA noise error                          */
#define IRDA_FLAG_FE                        USART_ISR_FE            /*!< IRDA frame error                          */
#define IRDA_FLAG_PE                        USART_ISR_PE            /*!< IRDA parity error                         */
/**
  * @}
  */

/** @defgroup IRDA_Interrupt_definition IRDA Interrupts Definition
  *        Elements values convention: 0000ZZZZ0XXYYYYYb
  *           - YYYYY  : Interrupt source position in the XX register (5bits)
  *           - XX  : Interrupt source register (2bits)
  *                 - 01: CR1 register
  *                 - 10: CR2 register
  *                 - 11: CR3 register
  *           - ZZZZ  : Flag position in the ISR register(4bits)
  * @{
  */
#define IRDA_IT_PE                          0x0028U     /*!< IRDA Parity error interruption                 */
#define IRDA_IT_TXE                         0x0727U     /*!< IRDA Transmit data register empty interruption */
#define IRDA_IT_TC                          0x0626U     /*!< IRDA Transmission complete interruption        */
#define IRDA_IT_RXNE                        0x0525U     /*!< IRDA Read data register not empty interruption */
#define IRDA_IT_IDLE                        0x0424U     /*!< IRDA Idle interruption                         */

/*       Elements values convention: 000000000XXYYYYYb
             - YYYYY  : Interrupt source position in the XX register (5bits)
             - XX  : Interrupt source register (2bits)
                   - 01: CR1 register
                   - 10: CR2 register
                   - 11: CR3 register */
#define IRDA_IT_ERR                         0x0060U       /*!< IRDA Error interruption        */

/*       Elements values convention: 0000ZZZZ00000000b
             - ZZZZ  : Flag position in the ISR register(4bits) */
#define IRDA_IT_ORE                         0x0300U      /*!< IRDA Overrun error interruption */
#define IRDA_IT_NE                          0x0200U      /*!< IRDA Noise error interruption   */
#define IRDA_IT_FE                          0x0100U      /*!< IRDA Frame error interruption   */
/**
  * @}
  */

/** @defgroup IRDA_IT_CLEAR_Flags IRDA Interruption Clear Flags
  * @{
  */
#define IRDA_CLEAR_PEF                       USART_ICR_PECF            /*!< Parity Error Clear Flag          */
#define IRDA_CLEAR_FEF                       USART_ICR_FECF            /*!< Framing Error Clear Flag         */
#define IRDA_CLEAR_NEF                       USART_ICR_NCF            /*!< Noise Error detected Clear Flag  */
#define IRDA_CLEAR_OREF                      USART_ICR_ORECF           /*!< OverRun Error Clear Flag         */
#define IRDA_CLEAR_IDLEF                     USART_ICR_IDLECF          /*!< IDLE line detected Clear Flag    */
#define IRDA_CLEAR_TCF                       USART_ICR_TCCF            /*!< Transmission Complete Clear Flag */
/**
  * @}
  */

/** @defgroup IRDA_Interruption_Mask IRDA interruptions flags mask
  * @{
  */
#define IRDA_IT_MASK  0x001FU  /*!< IRDA Interruptions flags mask  */
#define IRDA_CR_MASK  0x00E0U  /*!< IRDA control register mask     */
#define IRDA_CR_POS   5U       /*!< IRDA control register position */
#define IRDA_ISR_MASK 0x1F00U  /*!< IRDA ISR register mask         */
#define IRDA_ISR_POS  8U       /*!< IRDA ISR register position     */
/**
  * @}
  */

/**
  * @}
  */

/* Exported macros -----------------------------------------------------------*/
/** @defgroup IRDA_Exported_Macros IRDA Exported Macros
  * @{
  */

/** @brief  Reset IRDA handle state.
  * @param  __HANDLE__ IRDA handle.
  * @retval None
  */
#if USE_HAL_IRDA_REGISTER_CALLBACKS == 1
#define __HAL_IRDA_RESET_HANDLE_STATE(__HANDLE__)  do{                                                   \
                                                       (__HANDLE__)->gState = HAL_IRDA_STATE_RESET;      \
                                                       (__HANDLE__)->RxState = HAL_IRDA_STATE_RESET;     \
                                                       (__HANDLE__)->MspInitCallback = NULL;             \
                                                       (__HANDLE__)->MspDeInitCallback = NULL;           \
                                                     } while(0U)
#else
#define __HAL_IRDA_RESET_HANDLE_STATE(__HANDLE__)  do{                                                   \
                                                       (__HANDLE__)->gState = HAL_IRDA_STATE_RESET;      \
                                                       (__HANDLE__)->RxState = HAL_IRDA_STATE_RESET;     \
                                                     } while(0U)
#endif /*USE_HAL_IRDA_REGISTER_CALLBACKS  */

/** @brief  Flush the IRDA DR register.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_FLUSH_DRREGISTER(__HANDLE__)                            \
  do{                                                                    \
    SET_BIT((__HANDLE__)->Instance->RQR, IRDA_RXDATA_FLUSH_REQUEST); \
    SET_BIT((__HANDLE__)->Instance->RQR, IRDA_TXDATA_FLUSH_REQUEST); \
  } while(0U)

/** @brief  Clear the specified IRDA pending flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __FLAG__ specifies the flag to check.
  *          This parameter can be any combination of the following values:
  *            @arg @ref IRDA_CLEAR_PEF
  *            @arg @ref IRDA_CLEAR_FEF
  *            @arg @ref IRDA_CLEAR_NEF
  *            @arg @ref IRDA_CLEAR_OREF
  *            @arg @ref IRDA_CLEAR_TCF
  *            @arg @ref IRDA_CLEAR_IDLEF
  * @retval None
  */
#define __HAL_IRDA_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__))

/** @brief  Clear the IRDA PE pending flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)    __HAL_IRDA_CLEAR_FLAG((__HANDLE__), IRDA_CLEAR_PEF)


/** @brief  Clear the IRDA FE pending flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_CLEAR_FEFLAG(__HANDLE__)    __HAL_IRDA_CLEAR_FLAG((__HANDLE__), IRDA_CLEAR_FEF)

/** @brief  Clear the IRDA NE pending flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_CLEAR_NEFLAG(__HANDLE__)    __HAL_IRDA_CLEAR_FLAG((__HANDLE__), IRDA_CLEAR_NEF)

/** @brief  Clear the IRDA ORE pending flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_CLEAR_OREFLAG(__HANDLE__)    __HAL_IRDA_CLEAR_FLAG((__HANDLE__), IRDA_CLEAR_OREF)

/** @brief  Clear the IRDA IDLE pending flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_CLEAR_IDLEFLAG(__HANDLE__)   __HAL_IRDA_CLEAR_FLAG((__HANDLE__), IRDA_CLEAR_IDLEF)

/** @brief  Check whether the specified IRDA flag is set or not.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __FLAG__ specifies the flag to check.
  *        This parameter can be one of the following values:
  *            @arg @ref IRDA_FLAG_TEACK Transmit enable acknowledge flag
  *            @arg @ref IRDA_FLAG_BUSY  Busy flag
  *            @arg @ref IRDA_FLAG_ABRF  Auto Baud rate detection flag
  *            @arg @ref IRDA_FLAG_ABRE  Auto Baud rate detection error flag
  *            @arg @ref IRDA_FLAG_TXE   Transmit data register empty flag
  *            @arg @ref IRDA_FLAG_TC    Transmission Complete flag
  *            @arg @ref IRDA_FLAG_RXNE  Receive data register not empty flag
  *            @arg @ref IRDA_FLAG_ORE   OverRun Error flag
  *            @arg @ref IRDA_FLAG_NE    Noise Error flag
  *            @arg @ref IRDA_FLAG_FE    Framing Error flag
  *            @arg @ref IRDA_FLAG_PE    Parity Error flag
  * @retval The new state of __FLAG__ (TRUE or FALSE).
  */
#define __HAL_IRDA_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))


/** @brief  Enable the specified IRDA interrupt.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __INTERRUPT__ specifies the IRDA interrupt source to enable.
  *          This parameter can be one of the following values:
  *            @arg @ref IRDA_IT_TXE  Transmit Data Register empty interrupt
  *            @arg @ref IRDA_IT_TC   Transmission complete interrupt
  *            @arg @ref IRDA_IT_RXNE Receive Data register not empty interrupt
  *            @arg @ref IRDA_IT_IDLE Idle line detection interrupt
  *            @arg @ref IRDA_IT_PE   Parity Error interrupt
  *            @arg @ref IRDA_IT_ERR  Error interrupt(Frame error, noise error, overrun error)
  * @retval None
  */
#define __HAL_IRDA_ENABLE_IT(__HANDLE__, __INTERRUPT__)   (((((__INTERRUPT__) & IRDA_CR_MASK) >> IRDA_CR_POS) == 1U)? ((__HANDLE__)->Instance->CR1 |= ((uint32_t)1U << ((__INTERRUPT__) & IRDA_IT_MASK))): \
                                                           ((((__INTERRUPT__) & IRDA_CR_MASK) >> IRDA_CR_POS) == 2U)? ((__HANDLE__)->Instance->CR2 |= ((uint32_t)1U << ((__INTERRUPT__) & IRDA_IT_MASK))): \
                                                           ((__HANDLE__)->Instance->CR3 |= ((uint32_t)1U << ((__INTERRUPT__) & IRDA_IT_MASK))))

/** @brief  Disable the specified IRDA interrupt.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __INTERRUPT__ specifies the IRDA interrupt source to disable.
  *          This parameter can be one of the following values:
  *            @arg @ref IRDA_IT_TXE  Transmit Data Register empty interrupt
  *            @arg @ref IRDA_IT_TC   Transmission complete interrupt
  *            @arg @ref IRDA_IT_RXNE Receive Data register not empty interrupt
  *            @arg @ref IRDA_IT_IDLE Idle line detection interrupt
  *            @arg @ref IRDA_IT_PE   Parity Error interrupt
  *            @arg @ref IRDA_IT_ERR  Error interrupt(Frame error, noise error, overrun error)
  * @retval None
  */
#define __HAL_IRDA_DISABLE_IT(__HANDLE__, __INTERRUPT__)  (((((__INTERRUPT__) & IRDA_CR_MASK) >> IRDA_CR_POS) == 1U)? ((__HANDLE__)->Instance->CR1 &= ~ ((uint32_t)1U << ((__INTERRUPT__) & IRDA_IT_MASK))): \
                                                           ((((__INTERRUPT__) & IRDA_CR_MASK) >> IRDA_CR_POS) == 2U)? ((__HANDLE__)->Instance->CR2 &= ~ ((uint32_t)1U << ((__INTERRUPT__) & IRDA_IT_MASK))): \
                                                           ((__HANDLE__)->Instance->CR3 &= ~ ((uint32_t)1U << ((__INTERRUPT__) & IRDA_IT_MASK))))


/** @brief  Check whether the specified IRDA interrupt has occurred or not.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __INTERRUPT__ specifies the IRDA interrupt source to check.
  *          This parameter can be one of the following values:
  *            @arg @ref IRDA_IT_TXE Transmit Data Register empty interrupt
  *            @arg @ref IRDA_IT_TC  Transmission complete interrupt
  *            @arg @ref IRDA_IT_RXNE Receive Data register not empty interrupt
  *            @arg @ref IRDA_IT_IDLE Idle line detection interrupt
  *            @arg @ref IRDA_IT_ORE OverRun Error interrupt
  *            @arg @ref IRDA_IT_NE Noise Error interrupt
  *            @arg @ref IRDA_IT_FE Framing Error interrupt
  *            @arg @ref IRDA_IT_PE Parity Error interrupt
  * @retval The new state of __IT__ (SET or RESET).
  */
#define __HAL_IRDA_GET_IT(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->ISR\
                                                        & (0x01U << (((__INTERRUPT__) & IRDA_ISR_MASK)>> IRDA_ISR_POS))) != 0U) ? SET : RESET)

/** @brief  Check whether the specified IRDA interrupt source is enabled or not.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __INTERRUPT__ specifies the IRDA interrupt source to check.
  *          This parameter can be one of the following values:
  *            @arg @ref IRDA_IT_TXE Transmit Data Register empty interrupt
  *            @arg @ref IRDA_IT_TC  Transmission complete interrupt
  *            @arg @ref IRDA_IT_RXNE Receive Data register not empty interrupt
  *            @arg @ref IRDA_IT_IDLE Idle line detection interrupt
  *            @arg @ref IRDA_IT_ERR Framing, overrun or noise error interrupt
  *            @arg @ref IRDA_IT_PE Parity Error interrupt
  * @retval The new state of __IT__ (SET or RESET).
  */
#define __HAL_IRDA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((((((__INTERRUPT__) & IRDA_CR_MASK) >> IRDA_CR_POS) == 0x01U)? (__HANDLE__)->Instance->CR1 : \
                                                                (((((__INTERRUPT__) & IRDA_CR_MASK) >> IRDA_CR_POS) == 0x02U)? (__HANDLE__)->Instance->CR2 : \
                                                                 (__HANDLE__)->Instance->CR3)) & ((uint32_t)0x01U << (((uint16_t)(__INTERRUPT__)) & IRDA_IT_MASK))) != 0U) ? SET : RESET)

/** @brief  Clear the specified IRDA ISR flag, in setting the proper ICR register flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __IT_CLEAR__ specifies the interrupt clear register flag that needs to be set
  *                       to clear the corresponding interrupt
  *          This parameter can be one of the following values:
  *            @arg @ref IRDA_CLEAR_PEF Parity Error Clear Flag
  *            @arg @ref IRDA_CLEAR_FEF Framing Error Clear Flag
  *            @arg @ref IRDA_CLEAR_NEF Noise detected Clear Flag
  *            @arg @ref IRDA_CLEAR_OREF OverRun Error Clear Flag
  *            @arg @ref IRDA_CLEAR_TCF Transmission Complete Clear Flag
  * @retval None
  */
#define __HAL_IRDA_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))


/** @brief  Set a specific IRDA request flag.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @param  __REQ__ specifies the request flag to set
  *          This parameter can be one of the following values:
  *            @arg @ref IRDA_AUTOBAUD_REQUEST Auto-Baud Rate Request
  *            @arg @ref IRDA_RXDATA_FLUSH_REQUEST Receive Data flush Request
  *            @arg @ref IRDA_TXDATA_FLUSH_REQUEST Transmit data flush Request
  * @retval None
  */
#define __HAL_IRDA_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))

/** @brief  Enable the IRDA one bit sample method.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)

/** @brief  Disable the IRDA one bit sample method.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3\
                                                       &= (uint32_t)~((uint32_t)USART_CR3_ONEBIT))

/** @brief  Enable UART/USART associated to IRDA Handle.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_ENABLE(__HANDLE__)                   ((__HANDLE__)->Instance->CR1 |=  USART_CR1_UE)

/** @brief  Disable UART/USART associated to IRDA Handle.
  * @param  __HANDLE__ specifies the IRDA Handle.
  * @retval None
  */
#define __HAL_IRDA_DISABLE(__HANDLE__)                  ((__HANDLE__)->Instance->CR1 &=  ~USART_CR1_UE)

/**
  * @}
  */

/* Private macros --------------------------------------------------------*/
/** @addtogroup IRDA_Private_Macros
  * @{
  */

/** @brief  Ensure that IRDA Baud rate is less or equal to maximum value.
  * @param  __BAUDRATE__ specifies the IRDA Baudrate set by the user.
  * @retval True or False
  */
#define IS_IRDA_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 115201U)

/** @brief  Ensure that IRDA prescaler value is strictly larger than 0.
  * @param  __PRESCALER__ specifies the IRDA prescaler value set by the user.
  * @retval True or False
  */
#define IS_IRDA_PRESCALER(__PRESCALER__) ((__PRESCALER__) > 0U)

/** @brief Ensure that IRDA frame parity is valid.
  * @param __PARITY__ IRDA frame parity.
  * @retval SET (__PARITY__ is valid) or RESET (__PARITY__ is invalid)
  */
#define IS_IRDA_PARITY(__PARITY__) (((__PARITY__) == IRDA_PARITY_NONE) || \
                                    ((__PARITY__) == IRDA_PARITY_EVEN) || \
                                    ((__PARITY__) == IRDA_PARITY_ODD))

/** @brief Ensure that IRDA communication mode is valid.
  * @param __MODE__ IRDA communication mode.
  * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
  */
#define IS_IRDA_TX_RX_MODE(__MODE__) ((((__MODE__)\
                                        & (~((uint32_t)(IRDA_MODE_TX_RX)))) == 0x00U) && ((__MODE__) != 0x00U))

/** @brief Ensure that IRDA power mode is valid.
  * @param __MODE__ IRDA power mode.
  * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
  */
#define IS_IRDA_POWERMODE(__MODE__) (((__MODE__) == IRDA_POWERMODE_LOWPOWER) || \
                                     ((__MODE__) == IRDA_POWERMODE_NORMAL))

/** @brief Ensure that IRDA state is valid.
  * @param __STATE__ IRDA state mode.
  * @retval SET (__STATE__ is valid) or RESET (__STATE__ is invalid)
  */
#define IS_IRDA_STATE(__STATE__) (((__STATE__) == IRDA_STATE_DISABLE) || \
                                  ((__STATE__) == IRDA_STATE_ENABLE))

/** @brief Ensure that IRDA associated UART/USART mode is valid.
  * @param __MODE__ IRDA associated UART/USART mode.
  * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
  */
#define IS_IRDA_MODE(__MODE__)  (((__MODE__) == IRDA_MODE_DISABLE) || \
                                 ((__MODE__) == IRDA_MODE_ENABLE))

/** @brief Ensure that IRDA sampling rate is valid.
  * @param __ONEBIT__ IRDA sampling rate.
  * @retval SET (__ONEBIT__ is valid) or RESET (__ONEBIT__ is invalid)
  */
#define IS_IRDA_ONE_BIT_SAMPLE(__ONEBIT__)      (((__ONEBIT__) == IRDA_ONE_BIT_SAMPLE_DISABLE) || \
                                                 ((__ONEBIT__) == IRDA_ONE_BIT_SAMPLE_ENABLE))

/** @brief Ensure that IRDA DMA TX mode is valid.
  * @param __DMATX__ IRDA DMA TX mode.
  * @retval SET (__DMATX__ is valid) or RESET (__DMATX__ is invalid)
  */
#define IS_IRDA_DMA_TX(__DMATX__)     (((__DMATX__) == IRDA_DMA_TX_DISABLE) || \
                                       ((__DMATX__) == IRDA_DMA_TX_ENABLE))

/** @brief Ensure that IRDA DMA RX mode is valid.
  * @param __DMARX__ IRDA DMA RX mode.
  * @retval SET (__DMARX__ is valid) or RESET (__DMARX__ is invalid)
  */
#define IS_IRDA_DMA_RX(__DMARX__) (((__DMARX__) == IRDA_DMA_RX_DISABLE) || \
                                   ((__DMARX__) == IRDA_DMA_RX_ENABLE))

/** @brief Ensure that IRDA request is valid.
  * @param __PARAM__ IRDA request.
  * @retval SET (__PARAM__ is valid) or RESET (__PARAM__ is invalid)
  */
#define IS_IRDA_REQUEST_PARAMETER(__PARAM__) (((__PARAM__) == IRDA_AUTOBAUD_REQUEST) || \
                                              ((__PARAM__) == IRDA_RXDATA_FLUSH_REQUEST) || \
                                              ((__PARAM__) == IRDA_TXDATA_FLUSH_REQUEST))
/**
  * @}
  */

/* Include IRDA HAL Extended module */
#include "stm32f7xx_hal_irda_ex.h"

/* Exported functions --------------------------------------------------------*/
/** @addtogroup IRDA_Exported_Functions IRDA Exported Functions
  * @{
  */

/** @addtogroup IRDA_Exported_Functions_Group1 Initialization and de-initialization functions
  * @{
  */

/* Initialization and de-initialization functions  ****************************/
HAL_StatusTypeDef HAL_IRDA_Init(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_DeInit(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_MspInit(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_MspDeInit(IRDA_HandleTypeDef *hirda);

#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
/* Callbacks Register/UnRegister functions  ***********************************/
HAL_StatusTypeDef HAL_IRDA_RegisterCallback(IRDA_HandleTypeDef *hirda, HAL_IRDA_CallbackIDTypeDef CallbackID,
                                            pIRDA_CallbackTypeDef pCallback);
HAL_StatusTypeDef HAL_IRDA_UnRegisterCallback(IRDA_HandleTypeDef *hirda, HAL_IRDA_CallbackIDTypeDef CallbackID);
#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */

/**
  * @}
  */

/** @addtogroup IRDA_Exported_Functions_Group2 IO operation functions
  * @{
  */

/* IO operation functions *****************************************************/
HAL_StatusTypeDef HAL_IRDA_Transmit(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_IRDA_Receive(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_Receive_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_Transmit_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_Receive_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_IRDA_DMAPause(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_DMAResume(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_DMAStop(IRDA_HandleTypeDef *hirda);
/* Transfer Abort functions */
HAL_StatusTypeDef HAL_IRDA_Abort(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortTransmit(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortReceive(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_Abort_IT(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortTransmit_IT(IRDA_HandleTypeDef *hirda);
HAL_StatusTypeDef HAL_IRDA_AbortReceive_IT(IRDA_HandleTypeDef *hirda);

void HAL_IRDA_IRQHandler(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_TxCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_RxCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_TxHalfCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_RxHalfCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_ErrorCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_AbortCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_AbortTransmitCpltCallback(IRDA_HandleTypeDef *hirda);
void HAL_IRDA_AbortReceiveCpltCallback(IRDA_HandleTypeDef *hirda);

/**
  * @}
  */

/* Peripheral Control functions  ************************************************/

/** @addtogroup IRDA_Exported_Functions_Group4 Peripheral State and Error functions
  * @{
  */

/* Peripheral State and Error functions ***************************************/
HAL_IRDA_StateTypeDef HAL_IRDA_GetState(IRDA_HandleTypeDef *hirda);
uint32_t              HAL_IRDA_GetError(IRDA_HandleTypeDef *hirda);

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

#ifdef __cplusplus
}
#endif

#endif /* STM32F7xx_HAL_IRDA_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/