| /** | |
| ****************************************************************************** | |
| * @file stm32f7xx_hal_pcd.c | |
| * @author MCD Application Team | |
| * @brief PCD HAL module driver. | |
| * This file provides firmware functions to manage the following | |
| * functionalities of the USB Peripheral Controller: | |
| * + Initialization and de-initialization functions | |
| * + IO operation functions | |
| * + Peripheral Control functions | |
| * + Peripheral State functions | |
| * | |
| ****************************************************************************** | |
| * @attention | |
| * | |
| * Copyright (c) 2017 STMicroelectronics. | |
| * All rights reserved. | |
| * | |
| * This software is licensed under terms that can be found in the LICENSE file | |
| * in the root directory of this software component. | |
| * If no LICENSE file comes with this software, it is provided AS-IS. | |
| * | |
| ****************************************************************************** | |
| @verbatim | |
| ============================================================================== | |
| ##### How to use this driver ##### | |
| ============================================================================== | |
| [..] | |
| The PCD HAL driver can be used as follows: | |
| (#) Declare a PCD_HandleTypeDef handle structure, for example: | |
| PCD_HandleTypeDef hpcd; | |
| (#) Fill parameters of Init structure in HCD handle | |
| (#) Call HAL_PCD_Init() API to initialize the PCD peripheral (Core, Device core, ...) | |
| (#) Initialize the PCD low level resources through the HAL_PCD_MspInit() API: | |
| (##) Enable the PCD/USB Low Level interface clock using | |
| (+++) __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); | |
| (+++) __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); (For High Speed Mode) | |
| (##) Initialize the related GPIO clocks | |
| (##) Configure PCD pin-out | |
| (##) Configure PCD NVIC interrupt | |
| (#)Associate the Upper USB device stack to the HAL PCD Driver: | |
| (##) hpcd.pData = pdev; | |
| (#)Enable PCD transmission and reception: | |
| (##) HAL_PCD_Start(); | |
| @endverbatim | |
| ****************************************************************************** | |
| */ | |
| /* Includes ------------------------------------------------------------------*/ | |
| #include "stm32f7xx_hal.h" | |
| /** @addtogroup STM32F7xx_HAL_Driver | |
| * @{ | |
| */ | |
| /** @defgroup PCD PCD | |
| * @brief PCD HAL module driver | |
| * @{ | |
| */ | |
| #ifdef HAL_PCD_MODULE_ENABLED | |
| #if defined (USB_OTG_FS) || defined (USB_OTG_HS) | |
| /* Private types -------------------------------------------------------------*/ | |
| /* Private variables ---------------------------------------------------------*/ | |
| /* Private constants ---------------------------------------------------------*/ | |
| /* Private macros ------------------------------------------------------------*/ | |
| /** @defgroup PCD_Private_Macros PCD Private Macros | |
| * @{ | |
| */ | |
| #define PCD_MIN(a, b) (((a) < (b)) ? (a) : (b)) | |
| #define PCD_MAX(a, b) (((a) > (b)) ? (a) : (b)) | |
| /** | |
| * @} | |
| */ | |
| /* Private functions prototypes ----------------------------------------------*/ | |
| /** @defgroup PCD_Private_Functions PCD Private Functions | |
| * @{ | |
| */ | |
| #if defined (USB_OTG_FS) || defined (USB_OTG_HS) | |
| static HAL_StatusTypeDef PCD_WriteEmptyTxFifo(PCD_HandleTypeDef *hpcd, uint32_t epnum); | |
| static HAL_StatusTypeDef PCD_EP_OutXfrComplete_int(PCD_HandleTypeDef *hpcd, uint32_t epnum); | |
| static HAL_StatusTypeDef PCD_EP_OutSetupPacket_int(PCD_HandleTypeDef *hpcd, uint32_t epnum); | |
| #endif /* defined (USB_OTG_FS) || defined (USB_OTG_HS) */ | |
| /** | |
| * @} | |
| */ | |
| /* Exported functions --------------------------------------------------------*/ | |
| /** @defgroup PCD_Exported_Functions PCD Exported Functions | |
| * @{ | |
| */ | |
| /** @defgroup PCD_Exported_Functions_Group1 Initialization and de-initialization functions | |
| * @brief Initialization and Configuration functions | |
| * | |
| @verbatim | |
| =============================================================================== | |
| ##### Initialization and de-initialization functions ##### | |
| =============================================================================== | |
| [..] This section provides functions allowing to: | |
| @endverbatim | |
| * @{ | |
| */ | |
| /** | |
| * @brief Initializes the PCD according to the specified | |
| * parameters in the PCD_InitTypeDef and initialize the associated handle. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_Init(PCD_HandleTypeDef *hpcd) | |
| { | |
| #if defined (USB_OTG_FS) | |
| const USB_OTG_GlobalTypeDef *USBx; | |
| #endif /* defined (USB_OTG_FS) */ | |
| uint8_t i; | |
| /* Check the PCD handle allocation */ | |
| if (hpcd == NULL) | |
| { | |
| return HAL_ERROR; | |
| } | |
| /* Check the parameters */ | |
| assert_param(IS_PCD_ALL_INSTANCE(hpcd->Instance)); | |
| #if defined (USB_OTG_FS) | |
| USBx = hpcd->Instance; | |
| #endif /* defined (USB_OTG_FS) */ | |
| if (hpcd->State == HAL_PCD_STATE_RESET) | |
| { | |
| /* Allocate lock resource and initialize it */ | |
| hpcd->Lock = HAL_UNLOCKED; | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->SOFCallback = HAL_PCD_SOFCallback; | |
| hpcd->SetupStageCallback = HAL_PCD_SetupStageCallback; | |
| hpcd->ResetCallback = HAL_PCD_ResetCallback; | |
| hpcd->SuspendCallback = HAL_PCD_SuspendCallback; | |
| hpcd->ResumeCallback = HAL_PCD_ResumeCallback; | |
| hpcd->ConnectCallback = HAL_PCD_ConnectCallback; | |
| hpcd->DisconnectCallback = HAL_PCD_DisconnectCallback; | |
| hpcd->DataOutStageCallback = HAL_PCD_DataOutStageCallback; | |
| hpcd->DataInStageCallback = HAL_PCD_DataInStageCallback; | |
| hpcd->ISOOUTIncompleteCallback = HAL_PCD_ISOOUTIncompleteCallback; | |
| hpcd->ISOINIncompleteCallback = HAL_PCD_ISOINIncompleteCallback; | |
| if (hpcd->MspInitCallback == NULL) | |
| { | |
| hpcd->MspInitCallback = HAL_PCD_MspInit; | |
| } | |
| /* Init the low level hardware */ | |
| hpcd->MspInitCallback(hpcd); | |
| #else | |
| /* Init the low level hardware : GPIO, CLOCK, NVIC... */ | |
| HAL_PCD_MspInit(hpcd); | |
| #endif /* (USE_HAL_PCD_REGISTER_CALLBACKS) */ | |
| } | |
| hpcd->State = HAL_PCD_STATE_BUSY; | |
| #if defined (USB_OTG_FS) | |
| /* Disable DMA mode for FS instance */ | |
| if (USBx == USB_OTG_FS) | |
| { | |
| hpcd->Init.dma_enable = 0U; | |
| } | |
| #endif /* defined (USB_OTG_FS) */ | |
| /* Disable the Interrupts */ | |
| __HAL_PCD_DISABLE(hpcd); | |
| /*Init the Core (common init.) */ | |
| if (USB_CoreInit(hpcd->Instance, hpcd->Init) != HAL_OK) | |
| { | |
| hpcd->State = HAL_PCD_STATE_ERROR; | |
| return HAL_ERROR; | |
| } | |
| /* Force Device Mode */ | |
| if (USB_SetCurrentMode(hpcd->Instance, USB_DEVICE_MODE) != HAL_OK) | |
| { | |
| hpcd->State = HAL_PCD_STATE_ERROR; | |
| return HAL_ERROR; | |
| } | |
| /* Init endpoints structures */ | |
| for (i = 0U; i < hpcd->Init.dev_endpoints; i++) | |
| { | |
| /* Init ep structure */ | |
| hpcd->IN_ep[i].is_in = 1U; | |
| hpcd->IN_ep[i].num = i; | |
| hpcd->IN_ep[i].tx_fifo_num = i; | |
| /* Control until ep is activated */ | |
| hpcd->IN_ep[i].type = EP_TYPE_CTRL; | |
| hpcd->IN_ep[i].maxpacket = 0U; | |
| hpcd->IN_ep[i].xfer_buff = 0U; | |
| hpcd->IN_ep[i].xfer_len = 0U; | |
| } | |
| for (i = 0U; i < hpcd->Init.dev_endpoints; i++) | |
| { | |
| hpcd->OUT_ep[i].is_in = 0U; | |
| hpcd->OUT_ep[i].num = i; | |
| /* Control until ep is activated */ | |
| hpcd->OUT_ep[i].type = EP_TYPE_CTRL; | |
| hpcd->OUT_ep[i].maxpacket = 0U; | |
| hpcd->OUT_ep[i].xfer_buff = 0U; | |
| hpcd->OUT_ep[i].xfer_len = 0U; | |
| } | |
| /* Init Device */ | |
| if (USB_DevInit(hpcd->Instance, hpcd->Init) != HAL_OK) | |
| { | |
| hpcd->State = HAL_PCD_STATE_ERROR; | |
| return HAL_ERROR; | |
| } | |
| hpcd->USB_Address = 0U; | |
| hpcd->State = HAL_PCD_STATE_READY; | |
| /* Activate LPM */ | |
| if (hpcd->Init.lpm_enable == 1U) | |
| { | |
| (void)HAL_PCDEx_ActivateLPM(hpcd); | |
| } | |
| (void)USB_DevDisconnect(hpcd->Instance); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief DeInitializes the PCD peripheral. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_DeInit(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Check the PCD handle allocation */ | |
| if (hpcd == NULL) | |
| { | |
| return HAL_ERROR; | |
| } | |
| hpcd->State = HAL_PCD_STATE_BUSY; | |
| /* Stop Device */ | |
| if (USB_StopDevice(hpcd->Instance) != HAL_OK) | |
| { | |
| return HAL_ERROR; | |
| } | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| if (hpcd->MspDeInitCallback == NULL) | |
| { | |
| hpcd->MspDeInitCallback = HAL_PCD_MspDeInit; /* Legacy weak MspDeInit */ | |
| } | |
| /* DeInit the low level hardware */ | |
| hpcd->MspDeInitCallback(hpcd); | |
| #else | |
| /* DeInit the low level hardware: CLOCK, NVIC.*/ | |
| HAL_PCD_MspDeInit(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| hpcd->State = HAL_PCD_STATE_RESET; | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Initializes the PCD MSP. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_MspInit could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief DeInitializes PCD MSP. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_MspDeInit(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_MspDeInit could be implemented in the user file | |
| */ | |
| } | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| /** | |
| * @brief Register a User USB PCD Callback | |
| * To be used instead of the weak predefined callback | |
| * @param hpcd USB PCD handle | |
| * @param CallbackID ID of the callback to be registered | |
| * This parameter can be one of the following values: | |
| * @arg @ref HAL_PCD_SOF_CB_ID USB PCD SOF callback ID | |
| * @arg @ref HAL_PCD_SETUPSTAGE_CB_ID USB PCD Setup callback ID | |
| * @arg @ref HAL_PCD_RESET_CB_ID USB PCD Reset callback ID | |
| * @arg @ref HAL_PCD_SUSPEND_CB_ID USB PCD Suspend callback ID | |
| * @arg @ref HAL_PCD_RESUME_CB_ID USB PCD Resume callback ID | |
| * @arg @ref HAL_PCD_CONNECT_CB_ID USB PCD Connect callback ID | |
| * @arg @ref HAL_PCD_DISCONNECT_CB_ID USB PCD Disconnect callback ID | |
| * @arg @ref HAL_PCD_MSPINIT_CB_ID MspDeInit callback ID | |
| * @arg @ref HAL_PCD_MSPDEINIT_CB_ID MspDeInit callback ID | |
| * @param pCallback pointer to the Callback function | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_RegisterCallback(PCD_HandleTypeDef *hpcd, | |
| HAL_PCD_CallbackIDTypeDef CallbackID, | |
| pPCD_CallbackTypeDef pCallback) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| if (pCallback == NULL) | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| return HAL_ERROR; | |
| } | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| switch (CallbackID) | |
| { | |
| case HAL_PCD_SOF_CB_ID : | |
| hpcd->SOFCallback = pCallback; | |
| break; | |
| case HAL_PCD_SETUPSTAGE_CB_ID : | |
| hpcd->SetupStageCallback = pCallback; | |
| break; | |
| case HAL_PCD_RESET_CB_ID : | |
| hpcd->ResetCallback = pCallback; | |
| break; | |
| case HAL_PCD_SUSPEND_CB_ID : | |
| hpcd->SuspendCallback = pCallback; | |
| break; | |
| case HAL_PCD_RESUME_CB_ID : | |
| hpcd->ResumeCallback = pCallback; | |
| break; | |
| case HAL_PCD_CONNECT_CB_ID : | |
| hpcd->ConnectCallback = pCallback; | |
| break; | |
| case HAL_PCD_DISCONNECT_CB_ID : | |
| hpcd->DisconnectCallback = pCallback; | |
| break; | |
| case HAL_PCD_MSPINIT_CB_ID : | |
| hpcd->MspInitCallback = pCallback; | |
| break; | |
| case HAL_PCD_MSPDEINIT_CB_ID : | |
| hpcd->MspDeInitCallback = pCallback; | |
| break; | |
| default : | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| break; | |
| } | |
| } | |
| else if (hpcd->State == HAL_PCD_STATE_RESET) | |
| { | |
| switch (CallbackID) | |
| { | |
| case HAL_PCD_MSPINIT_CB_ID : | |
| hpcd->MspInitCallback = pCallback; | |
| break; | |
| case HAL_PCD_MSPDEINIT_CB_ID : | |
| hpcd->MspDeInitCallback = pCallback; | |
| break; | |
| default : | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| break; | |
| } | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Unregister an USB PCD Callback | |
| * USB PCD callback is redirected to the weak predefined callback | |
| * @param hpcd USB PCD handle | |
| * @param CallbackID ID of the callback to be unregistered | |
| * This parameter can be one of the following values: | |
| * @arg @ref HAL_PCD_SOF_CB_ID USB PCD SOF callback ID | |
| * @arg @ref HAL_PCD_SETUPSTAGE_CB_ID USB PCD Setup callback ID | |
| * @arg @ref HAL_PCD_RESET_CB_ID USB PCD Reset callback ID | |
| * @arg @ref HAL_PCD_SUSPEND_CB_ID USB PCD Suspend callback ID | |
| * @arg @ref HAL_PCD_RESUME_CB_ID USB PCD Resume callback ID | |
| * @arg @ref HAL_PCD_CONNECT_CB_ID USB PCD Connect callback ID | |
| * @arg @ref HAL_PCD_DISCONNECT_CB_ID USB PCD Disconnect callback ID | |
| * @arg @ref HAL_PCD_MSPINIT_CB_ID MspDeInit callback ID | |
| * @arg @ref HAL_PCD_MSPDEINIT_CB_ID MspDeInit callback ID | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_UnRegisterCallback(PCD_HandleTypeDef *hpcd, HAL_PCD_CallbackIDTypeDef CallbackID) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| /* Setup Legacy weak Callbacks */ | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| switch (CallbackID) | |
| { | |
| case HAL_PCD_SOF_CB_ID : | |
| hpcd->SOFCallback = HAL_PCD_SOFCallback; | |
| break; | |
| case HAL_PCD_SETUPSTAGE_CB_ID : | |
| hpcd->SetupStageCallback = HAL_PCD_SetupStageCallback; | |
| break; | |
| case HAL_PCD_RESET_CB_ID : | |
| hpcd->ResetCallback = HAL_PCD_ResetCallback; | |
| break; | |
| case HAL_PCD_SUSPEND_CB_ID : | |
| hpcd->SuspendCallback = HAL_PCD_SuspendCallback; | |
| break; | |
| case HAL_PCD_RESUME_CB_ID : | |
| hpcd->ResumeCallback = HAL_PCD_ResumeCallback; | |
| break; | |
| case HAL_PCD_CONNECT_CB_ID : | |
| hpcd->ConnectCallback = HAL_PCD_ConnectCallback; | |
| break; | |
| case HAL_PCD_DISCONNECT_CB_ID : | |
| hpcd->DisconnectCallback = HAL_PCD_DisconnectCallback; | |
| break; | |
| case HAL_PCD_MSPINIT_CB_ID : | |
| hpcd->MspInitCallback = HAL_PCD_MspInit; | |
| break; | |
| case HAL_PCD_MSPDEINIT_CB_ID : | |
| hpcd->MspDeInitCallback = HAL_PCD_MspDeInit; | |
| break; | |
| default : | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| break; | |
| } | |
| } | |
| else if (hpcd->State == HAL_PCD_STATE_RESET) | |
| { | |
| switch (CallbackID) | |
| { | |
| case HAL_PCD_MSPINIT_CB_ID : | |
| hpcd->MspInitCallback = HAL_PCD_MspInit; | |
| break; | |
| case HAL_PCD_MSPDEINIT_CB_ID : | |
| hpcd->MspDeInitCallback = HAL_PCD_MspDeInit; | |
| break; | |
| default : | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| break; | |
| } | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Register USB PCD Data OUT Stage Callback | |
| * To be used instead of the weak HAL_PCD_DataOutStageCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @param pCallback pointer to the USB PCD Data OUT Stage Callback function | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_RegisterDataOutStageCallback(PCD_HandleTypeDef *hpcd, | |
| pPCD_DataOutStageCallbackTypeDef pCallback) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| if (pCallback == NULL) | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| return HAL_ERROR; | |
| } | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->DataOutStageCallback = pCallback; | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Unregister the USB PCD Data OUT Stage Callback | |
| * USB PCD Data OUT Stage Callback is redirected to the weak HAL_PCD_DataOutStageCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_UnRegisterDataOutStageCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->DataOutStageCallback = HAL_PCD_DataOutStageCallback; /* Legacy weak DataOutStageCallback */ | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Register USB PCD Data IN Stage Callback | |
| * To be used instead of the weak HAL_PCD_DataInStageCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @param pCallback pointer to the USB PCD Data IN Stage Callback function | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_RegisterDataInStageCallback(PCD_HandleTypeDef *hpcd, | |
| pPCD_DataInStageCallbackTypeDef pCallback) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| if (pCallback == NULL) | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| return HAL_ERROR; | |
| } | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->DataInStageCallback = pCallback; | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Unregister the USB PCD Data IN Stage Callback | |
| * USB PCD Data OUT Stage Callback is redirected to the weak HAL_PCD_DataInStageCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_UnRegisterDataInStageCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->DataInStageCallback = HAL_PCD_DataInStageCallback; /* Legacy weak DataInStageCallback */ | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Register USB PCD Iso OUT incomplete Callback | |
| * To be used instead of the weak HAL_PCD_ISOOUTIncompleteCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @param pCallback pointer to the USB PCD Iso OUT incomplete Callback function | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_RegisterIsoOutIncpltCallback(PCD_HandleTypeDef *hpcd, | |
| pPCD_IsoOutIncpltCallbackTypeDef pCallback) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| if (pCallback == NULL) | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| return HAL_ERROR; | |
| } | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->ISOOUTIncompleteCallback = pCallback; | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Unregister the USB PCD Iso OUT incomplete Callback | |
| * USB PCD Iso OUT incomplete Callback is redirected | |
| * to the weak HAL_PCD_ISOOUTIncompleteCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_UnRegisterIsoOutIncpltCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->ISOOUTIncompleteCallback = HAL_PCD_ISOOUTIncompleteCallback; /* Legacy weak ISOOUTIncompleteCallback */ | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Register USB PCD Iso IN incomplete Callback | |
| * To be used instead of the weak HAL_PCD_ISOINIncompleteCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @param pCallback pointer to the USB PCD Iso IN incomplete Callback function | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_RegisterIsoInIncpltCallback(PCD_HandleTypeDef *hpcd, | |
| pPCD_IsoInIncpltCallbackTypeDef pCallback) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| if (pCallback == NULL) | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| return HAL_ERROR; | |
| } | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->ISOINIncompleteCallback = pCallback; | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Unregister the USB PCD Iso IN incomplete Callback | |
| * USB PCD Iso IN incomplete Callback is redirected | |
| * to the weak HAL_PCD_ISOINIncompleteCallback() predefined callback | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_UnRegisterIsoInIncpltCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->ISOINIncompleteCallback = HAL_PCD_ISOINIncompleteCallback; /* Legacy weak ISOINIncompleteCallback */ | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Register USB PCD LPM Callback | |
| * To be used instead of the weak HAL_PCDEx_LPM_Callback() predefined callback | |
| * @param hpcd PCD handle | |
| * @param pCallback pointer to the USB PCD LPM Callback function | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_RegisterLpmCallback(PCD_HandleTypeDef *hpcd, pPCD_LpmCallbackTypeDef pCallback) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| if (pCallback == NULL) | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| return HAL_ERROR; | |
| } | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->LPMCallback = pCallback; | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| /** | |
| * @brief Unregister the USB PCD LPM Callback | |
| * USB LPM Callback is redirected to the weak HAL_PCDEx_LPM_Callback() predefined callback | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_UnRegisterLpmCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| HAL_StatusTypeDef status = HAL_OK; | |
| /* Process locked */ | |
| __HAL_LOCK(hpcd); | |
| if (hpcd->State == HAL_PCD_STATE_READY) | |
| { | |
| hpcd->LPMCallback = HAL_PCDEx_LPM_Callback; /* Legacy weak HAL_PCDEx_LPM_Callback */ | |
| } | |
| else | |
| { | |
| /* Update the error code */ | |
| hpcd->ErrorCode |= HAL_PCD_ERROR_INVALID_CALLBACK; | |
| /* Return error status */ | |
| status = HAL_ERROR; | |
| } | |
| /* Release Lock */ | |
| __HAL_UNLOCK(hpcd); | |
| return status; | |
| } | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PCD_Exported_Functions_Group2 Input and Output operation functions | |
| * @brief Data transfers functions | |
| * | |
| @verbatim | |
| =============================================================================== | |
| ##### IO operation functions ##### | |
| =============================================================================== | |
| [..] | |
| This subsection provides a set of functions allowing to manage the PCD data | |
| transfers. | |
| @endverbatim | |
| * @{ | |
| */ | |
| /** | |
| * @brief Start the USB device | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_Start(PCD_HandleTypeDef *hpcd) | |
| { | |
| __HAL_LOCK(hpcd); | |
| __HAL_PCD_ENABLE(hpcd); | |
| (void)USB_DevConnect(hpcd->Instance); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Stop the USB device. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_Stop(PCD_HandleTypeDef *hpcd) | |
| { | |
| __HAL_LOCK(hpcd); | |
| __HAL_PCD_DISABLE(hpcd); | |
| (void)USB_DevDisconnect(hpcd->Instance); | |
| (void)USB_FlushTxFifo(hpcd->Instance, 0x10U); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| #if defined (USB_OTG_FS) || defined (USB_OTG_HS) | |
| /** | |
| * @brief Handles PCD interrupt request. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| void HAL_PCD_IRQHandler(PCD_HandleTypeDef *hpcd) | |
| { | |
| USB_OTG_GlobalTypeDef *USBx = hpcd->Instance; | |
| uint32_t USBx_BASE = (uint32_t)USBx; | |
| USB_OTG_EPTypeDef *ep; | |
| uint32_t i; | |
| uint32_t ep_intr; | |
| uint32_t epint; | |
| uint32_t epnum; | |
| uint32_t fifoemptymsk; | |
| uint32_t RegVal; | |
| /* ensure that we are in device mode */ | |
| if (USB_GetMode(hpcd->Instance) == USB_OTG_MODE_DEVICE) | |
| { | |
| /* avoid spurious interrupt */ | |
| if (__HAL_PCD_IS_INVALID_INTERRUPT(hpcd)) | |
| { | |
| return; | |
| } | |
| /* store current frame number */ | |
| hpcd->FrameNumber = (USBx_DEVICE->DSTS & USB_OTG_DSTS_FNSOF_Msk) >> USB_OTG_DSTS_FNSOF_Pos; | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_MMIS)) | |
| { | |
| /* incorrect mode, acknowledge the interrupt */ | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_MMIS); | |
| } | |
| /* Handle RxQLevel Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_RXFLVL)) | |
| { | |
| USB_MASK_INTERRUPT(hpcd->Instance, USB_OTG_GINTSTS_RXFLVL); | |
| RegVal = USBx->GRXSTSP; | |
| ep = &hpcd->OUT_ep[RegVal & USB_OTG_GRXSTSP_EPNUM]; | |
| if (((RegVal & USB_OTG_GRXSTSP_PKTSTS) >> 17) == STS_DATA_UPDT) | |
| { | |
| if ((RegVal & USB_OTG_GRXSTSP_BCNT) != 0U) | |
| { | |
| (void)USB_ReadPacket(USBx, ep->xfer_buff, | |
| (uint16_t)((RegVal & USB_OTG_GRXSTSP_BCNT) >> 4)); | |
| ep->xfer_buff += (RegVal & USB_OTG_GRXSTSP_BCNT) >> 4; | |
| ep->xfer_count += (RegVal & USB_OTG_GRXSTSP_BCNT) >> 4; | |
| } | |
| } | |
| else if (((RegVal & USB_OTG_GRXSTSP_PKTSTS) >> 17) == STS_SETUP_UPDT) | |
| { | |
| (void)USB_ReadPacket(USBx, (uint8_t *)hpcd->Setup, 8U); | |
| ep->xfer_count += (RegVal & USB_OTG_GRXSTSP_BCNT) >> 4; | |
| } | |
| else | |
| { | |
| /* ... */ | |
| } | |
| USB_UNMASK_INTERRUPT(hpcd->Instance, USB_OTG_GINTSTS_RXFLVL); | |
| } | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_OEPINT)) | |
| { | |
| epnum = 0U; | |
| /* Read in the device interrupt bits */ | |
| ep_intr = USB_ReadDevAllOutEpInterrupt(hpcd->Instance); | |
| while (ep_intr != 0U) | |
| { | |
| if ((ep_intr & 0x1U) != 0U) | |
| { | |
| epint = USB_ReadDevOutEPInterrupt(hpcd->Instance, (uint8_t)epnum); | |
| if ((epint & USB_OTG_DOEPINT_XFRC) == USB_OTG_DOEPINT_XFRC) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_XFRC); | |
| (void)PCD_EP_OutXfrComplete_int(hpcd, epnum); | |
| } | |
| if ((epint & USB_OTG_DOEPINT_STUP) == USB_OTG_DOEPINT_STUP) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_STUP); | |
| /* Class B setup phase done for previous decoded setup */ | |
| (void)PCD_EP_OutSetupPacket_int(hpcd, epnum); | |
| } | |
| if ((epint & USB_OTG_DOEPINT_OTEPDIS) == USB_OTG_DOEPINT_OTEPDIS) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_OTEPDIS); | |
| } | |
| /* Clear OUT Endpoint disable interrupt */ | |
| if ((epint & USB_OTG_DOEPINT_EPDISD) == USB_OTG_DOEPINT_EPDISD) | |
| { | |
| if ((USBx->GINTSTS & USB_OTG_GINTSTS_BOUTNAKEFF) == USB_OTG_GINTSTS_BOUTNAKEFF) | |
| { | |
| USBx_DEVICE->DCTL |= USB_OTG_DCTL_CGONAK; | |
| } | |
| ep = &hpcd->OUT_ep[epnum]; | |
| if (ep->is_iso_incomplete == 1U) | |
| { | |
| ep->is_iso_incomplete = 0U; | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->ISOOUTIncompleteCallback(hpcd, (uint8_t)epnum); | |
| #else | |
| HAL_PCD_ISOOUTIncompleteCallback(hpcd, (uint8_t)epnum); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_EPDISD); | |
| } | |
| /* Clear Status Phase Received interrupt */ | |
| if ((epint & USB_OTG_DOEPINT_OTEPSPR) == USB_OTG_DOEPINT_OTEPSPR) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_OTEPSPR); | |
| } | |
| /* Clear OUT NAK interrupt */ | |
| if ((epint & USB_OTG_DOEPINT_NAK) == USB_OTG_DOEPINT_NAK) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_NAK); | |
| } | |
| } | |
| epnum++; | |
| ep_intr >>= 1U; | |
| } | |
| } | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_IEPINT)) | |
| { | |
| /* Read in the device interrupt bits */ | |
| ep_intr = USB_ReadDevAllInEpInterrupt(hpcd->Instance); | |
| epnum = 0U; | |
| while (ep_intr != 0U) | |
| { | |
| if ((ep_intr & 0x1U) != 0U) /* In ITR */ | |
| { | |
| epint = USB_ReadDevInEPInterrupt(hpcd->Instance, (uint8_t)epnum); | |
| if ((epint & USB_OTG_DIEPINT_XFRC) == USB_OTG_DIEPINT_XFRC) | |
| { | |
| fifoemptymsk = (uint32_t)(0x1UL << (epnum & EP_ADDR_MSK)); | |
| USBx_DEVICE->DIEPEMPMSK &= ~fifoemptymsk; | |
| CLEAR_IN_EP_INTR(epnum, USB_OTG_DIEPINT_XFRC); | |
| if (hpcd->Init.dma_enable == 1U) | |
| { | |
| hpcd->IN_ep[epnum].xfer_buff += hpcd->IN_ep[epnum].maxpacket; | |
| /* this is ZLP, so prepare EP0 for next setup */ | |
| if ((epnum == 0U) && (hpcd->IN_ep[epnum].xfer_len == 0U)) | |
| { | |
| /* prepare to rx more setup packets */ | |
| (void)USB_EP0_OutStart(hpcd->Instance, 1U, (uint8_t *)hpcd->Setup); | |
| } | |
| } | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->DataInStageCallback(hpcd, (uint8_t)epnum); | |
| #else | |
| HAL_PCD_DataInStageCallback(hpcd, (uint8_t)epnum); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| if ((epint & USB_OTG_DIEPINT_TOC) == USB_OTG_DIEPINT_TOC) | |
| { | |
| CLEAR_IN_EP_INTR(epnum, USB_OTG_DIEPINT_TOC); | |
| } | |
| if ((epint & USB_OTG_DIEPINT_ITTXFE) == USB_OTG_DIEPINT_ITTXFE) | |
| { | |
| CLEAR_IN_EP_INTR(epnum, USB_OTG_DIEPINT_ITTXFE); | |
| } | |
| if ((epint & USB_OTG_DIEPINT_INEPNE) == USB_OTG_DIEPINT_INEPNE) | |
| { | |
| CLEAR_IN_EP_INTR(epnum, USB_OTG_DIEPINT_INEPNE); | |
| } | |
| if ((epint & USB_OTG_DIEPINT_EPDISD) == USB_OTG_DIEPINT_EPDISD) | |
| { | |
| (void)USB_FlushTxFifo(USBx, epnum); | |
| ep = &hpcd->IN_ep[epnum]; | |
| if (ep->is_iso_incomplete == 1U) | |
| { | |
| ep->is_iso_incomplete = 0U; | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->ISOINIncompleteCallback(hpcd, (uint8_t)epnum); | |
| #else | |
| HAL_PCD_ISOINIncompleteCallback(hpcd, (uint8_t)epnum); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| CLEAR_IN_EP_INTR(epnum, USB_OTG_DIEPINT_EPDISD); | |
| } | |
| if ((epint & USB_OTG_DIEPINT_TXFE) == USB_OTG_DIEPINT_TXFE) | |
| { | |
| (void)PCD_WriteEmptyTxFifo(hpcd, epnum); | |
| } | |
| } | |
| epnum++; | |
| ep_intr >>= 1U; | |
| } | |
| } | |
| /* Handle Resume Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_WKUINT)) | |
| { | |
| /* Clear the Remote Wake-up Signaling */ | |
| USBx_DEVICE->DCTL &= ~USB_OTG_DCTL_RWUSIG; | |
| if (hpcd->LPM_State == LPM_L1) | |
| { | |
| hpcd->LPM_State = LPM_L0; | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->LPMCallback(hpcd, PCD_LPM_L0_ACTIVE); | |
| #else | |
| HAL_PCDEx_LPM_Callback(hpcd, PCD_LPM_L0_ACTIVE); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| else | |
| { | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->ResumeCallback(hpcd); | |
| #else | |
| HAL_PCD_ResumeCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_WKUINT); | |
| } | |
| /* Handle Suspend Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_USBSUSP)) | |
| { | |
| if ((USBx_DEVICE->DSTS & USB_OTG_DSTS_SUSPSTS) == USB_OTG_DSTS_SUSPSTS) | |
| { | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->SuspendCallback(hpcd); | |
| #else | |
| HAL_PCD_SuspendCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_USBSUSP); | |
| } | |
| /* Handle LPM Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_LPMINT)) | |
| { | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_LPMINT); | |
| if (hpcd->LPM_State == LPM_L0) | |
| { | |
| hpcd->LPM_State = LPM_L1; | |
| hpcd->BESL = (hpcd->Instance->GLPMCFG & USB_OTG_GLPMCFG_BESL) >> 2U; | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->LPMCallback(hpcd, PCD_LPM_L1_ACTIVE); | |
| #else | |
| HAL_PCDEx_LPM_Callback(hpcd, PCD_LPM_L1_ACTIVE); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| else | |
| { | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->SuspendCallback(hpcd); | |
| #else | |
| HAL_PCD_SuspendCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| } | |
| /* Handle Reset Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_USBRST)) | |
| { | |
| USBx_DEVICE->DCTL &= ~USB_OTG_DCTL_RWUSIG; | |
| (void)USB_FlushTxFifo(hpcd->Instance, 0x10U); | |
| for (i = 0U; i < hpcd->Init.dev_endpoints; i++) | |
| { | |
| USBx_INEP(i)->DIEPINT = 0xFB7FU; | |
| USBx_INEP(i)->DIEPCTL &= ~USB_OTG_DIEPCTL_STALL; | |
| USBx_OUTEP(i)->DOEPINT = 0xFB7FU; | |
| USBx_OUTEP(i)->DOEPCTL &= ~USB_OTG_DOEPCTL_STALL; | |
| USBx_OUTEP(i)->DOEPCTL |= USB_OTG_DOEPCTL_SNAK; | |
| } | |
| USBx_DEVICE->DAINTMSK |= 0x10001U; | |
| if (hpcd->Init.use_dedicated_ep1 != 0U) | |
| { | |
| USBx_DEVICE->DOUTEP1MSK |= USB_OTG_DOEPMSK_STUPM | | |
| USB_OTG_DOEPMSK_XFRCM | | |
| USB_OTG_DOEPMSK_EPDM; | |
| USBx_DEVICE->DINEP1MSK |= USB_OTG_DIEPMSK_TOM | | |
| USB_OTG_DIEPMSK_XFRCM | | |
| USB_OTG_DIEPMSK_EPDM; | |
| } | |
| else | |
| { | |
| USBx_DEVICE->DOEPMSK |= USB_OTG_DOEPMSK_STUPM | | |
| USB_OTG_DOEPMSK_XFRCM | | |
| USB_OTG_DOEPMSK_EPDM | | |
| USB_OTG_DOEPMSK_OTEPSPRM | | |
| USB_OTG_DOEPMSK_NAKM; | |
| USBx_DEVICE->DIEPMSK |= USB_OTG_DIEPMSK_TOM | | |
| USB_OTG_DIEPMSK_XFRCM | | |
| USB_OTG_DIEPMSK_EPDM; | |
| } | |
| /* Set Default Address to 0 */ | |
| USBx_DEVICE->DCFG &= ~USB_OTG_DCFG_DAD; | |
| /* setup EP0 to receive SETUP packets */ | |
| (void)USB_EP0_OutStart(hpcd->Instance, (uint8_t)hpcd->Init.dma_enable, | |
| (uint8_t *)hpcd->Setup); | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_USBRST); | |
| } | |
| /* Handle Enumeration done Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_ENUMDNE)) | |
| { | |
| (void)USB_ActivateSetup(hpcd->Instance); | |
| hpcd->Init.speed = USB_GetDevSpeed(hpcd->Instance); | |
| /* Set USB Turnaround time */ | |
| (void)USB_SetTurnaroundTime(hpcd->Instance, | |
| HAL_RCC_GetHCLKFreq(), | |
| (uint8_t)hpcd->Init.speed); | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->ResetCallback(hpcd); | |
| #else | |
| HAL_PCD_ResetCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_ENUMDNE); | |
| } | |
| /* Handle SOF Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_SOF)) | |
| { | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->SOFCallback(hpcd); | |
| #else | |
| HAL_PCD_SOFCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_SOF); | |
| } | |
| /* Handle Global OUT NAK effective Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_BOUTNAKEFF)) | |
| { | |
| USBx->GINTMSK &= ~USB_OTG_GINTMSK_GONAKEFFM; | |
| for (epnum = 1U; epnum < hpcd->Init.dev_endpoints; epnum++) | |
| { | |
| if (hpcd->OUT_ep[epnum].is_iso_incomplete == 1U) | |
| { | |
| /* Abort current transaction and disable the EP */ | |
| (void)HAL_PCD_EP_Abort(hpcd, (uint8_t)epnum); | |
| } | |
| } | |
| } | |
| /* Handle Incomplete ISO IN Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_IISOIXFR)) | |
| { | |
| for (epnum = 1U; epnum < hpcd->Init.dev_endpoints; epnum++) | |
| { | |
| RegVal = USBx_INEP(epnum)->DIEPCTL; | |
| if ((hpcd->IN_ep[epnum].type == EP_TYPE_ISOC) && | |
| ((RegVal & USB_OTG_DIEPCTL_EPENA) == USB_OTG_DIEPCTL_EPENA)) | |
| { | |
| hpcd->IN_ep[epnum].is_iso_incomplete = 1U; | |
| /* Abort current transaction and disable the EP */ | |
| (void)HAL_PCD_EP_Abort(hpcd, (uint8_t)(epnum | 0x80U)); | |
| } | |
| } | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_IISOIXFR); | |
| } | |
| /* Handle Incomplete ISO OUT Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_PXFR_INCOMPISOOUT)) | |
| { | |
| for (epnum = 1U; epnum < hpcd->Init.dev_endpoints; epnum++) | |
| { | |
| RegVal = USBx_OUTEP(epnum)->DOEPCTL; | |
| if ((hpcd->OUT_ep[epnum].type == EP_TYPE_ISOC) && | |
| ((RegVal & USB_OTG_DOEPCTL_EPENA) == USB_OTG_DOEPCTL_EPENA) && | |
| (((RegVal & (0x1U << 16U)) >> 16U) == (hpcd->FrameNumber & 0x1U))) | |
| { | |
| hpcd->OUT_ep[epnum].is_iso_incomplete = 1U; | |
| USBx->GINTMSK |= USB_OTG_GINTMSK_GONAKEFFM; | |
| if ((USBx->GINTSTS & USB_OTG_GINTSTS_BOUTNAKEFF) == 0U) | |
| { | |
| USBx_DEVICE->DCTL |= USB_OTG_DCTL_SGONAK; | |
| break; | |
| } | |
| } | |
| } | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_PXFR_INCOMPISOOUT); | |
| } | |
| /* Handle Connection event Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_SRQINT)) | |
| { | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->ConnectCallback(hpcd); | |
| #else | |
| HAL_PCD_ConnectCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| __HAL_PCD_CLEAR_FLAG(hpcd, USB_OTG_GINTSTS_SRQINT); | |
| } | |
| /* Handle Disconnection event Interrupt */ | |
| if (__HAL_PCD_GET_FLAG(hpcd, USB_OTG_GINTSTS_OTGINT)) | |
| { | |
| RegVal = hpcd->Instance->GOTGINT; | |
| if ((RegVal & USB_OTG_GOTGINT_SEDET) == USB_OTG_GOTGINT_SEDET) | |
| { | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->DisconnectCallback(hpcd); | |
| #else | |
| HAL_PCD_DisconnectCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| hpcd->Instance->GOTGINT |= RegVal; | |
| } | |
| } | |
| } | |
| /** | |
| * @brief Handles PCD Wakeup interrupt request. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| void HAL_PCD_WKUP_IRQHandler(PCD_HandleTypeDef *hpcd) | |
| { | |
| #if defined (USB_OTG_FS) | |
| USB_OTG_GlobalTypeDef *USBx; | |
| USBx = hpcd->Instance; | |
| if (USBx == USB_OTG_FS) | |
| { | |
| /* Clear EXTI pending Bit */ | |
| __HAL_USB_OTG_FS_WAKEUP_EXTI_CLEAR_FLAG(); | |
| } | |
| else | |
| #endif /* defined (USB_OTG_FS) */ | |
| { | |
| /* Clear EXTI pending Bit */ | |
| __HAL_USB_OTG_HS_WAKEUP_EXTI_CLEAR_FLAG(); | |
| } | |
| } | |
| #endif /* defined (USB_OTG_FS) || defined (USB_OTG_HS) */ | |
| /** | |
| * @brief Data OUT stage callback. | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_DataOutStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| UNUSED(epnum); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_DataOutStageCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Data IN stage callback | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_DataInStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| UNUSED(epnum); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_DataInStageCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Setup stage callback | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_SetupStageCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_SetupStageCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief USB Start Of Frame callback. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_SOFCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_SOFCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief USB Reset callback. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_ResetCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_ResetCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Suspend event callback. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_SuspendCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_SuspendCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Resume event callback. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_ResumeCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_ResumeCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Incomplete ISO OUT callback. | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_ISOOUTIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| UNUSED(epnum); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_ISOOUTIncompleteCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Incomplete ISO IN callback. | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_ISOINIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| UNUSED(epnum); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_ISOINIncompleteCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Connection event callback. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_ConnectCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_ConnectCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @brief Disconnection event callback. | |
| * @param hpcd PCD handle | |
| * @retval None | |
| */ | |
| __weak void HAL_PCD_DisconnectCallback(PCD_HandleTypeDef *hpcd) | |
| { | |
| /* Prevent unused argument(s) compilation warning */ | |
| UNUSED(hpcd); | |
| /* NOTE : This function should not be modified, when the callback is needed, | |
| the HAL_PCD_DisconnectCallback could be implemented in the user file | |
| */ | |
| } | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PCD_Exported_Functions_Group3 Peripheral Control functions | |
| * @brief management functions | |
| * | |
| @verbatim | |
| =============================================================================== | |
| ##### Peripheral Control functions ##### | |
| =============================================================================== | |
| [..] | |
| This subsection provides a set of functions allowing to control the PCD data | |
| transfers. | |
| @endverbatim | |
| * @{ | |
| */ | |
| /** | |
| * @brief Connect the USB device | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_DevConnect(PCD_HandleTypeDef *hpcd) | |
| { | |
| __HAL_LOCK(hpcd); | |
| (void)USB_DevConnect(hpcd->Instance); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Disconnect the USB device. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_DevDisconnect(PCD_HandleTypeDef *hpcd) | |
| { | |
| __HAL_LOCK(hpcd); | |
| (void)USB_DevDisconnect(hpcd->Instance); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Set the USB Device address. | |
| * @param hpcd PCD handle | |
| * @param address new device address | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_SetAddress(PCD_HandleTypeDef *hpcd, uint8_t address) | |
| { | |
| __HAL_LOCK(hpcd); | |
| hpcd->USB_Address = address; | |
| (void)USB_SetDevAddress(hpcd->Instance, address); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Open and configure an endpoint. | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @param ep_mps endpoint max packet size | |
| * @param ep_type endpoint type | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_Open(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, | |
| uint16_t ep_mps, uint8_t ep_type) | |
| { | |
| HAL_StatusTypeDef ret = HAL_OK; | |
| PCD_EPTypeDef *ep; | |
| if ((ep_addr & 0x80U) == 0x80U) | |
| { | |
| ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 1U; | |
| } | |
| else | |
| { | |
| ep = &hpcd->OUT_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 0U; | |
| } | |
| ep->num = ep_addr & EP_ADDR_MSK; | |
| ep->maxpacket = ep_mps; | |
| ep->type = ep_type; | |
| if (ep->is_in != 0U) | |
| { | |
| /* Assign a Tx FIFO */ | |
| ep->tx_fifo_num = ep->num; | |
| } | |
| /* Set initial data PID. */ | |
| if (ep_type == EP_TYPE_BULK) | |
| { | |
| ep->data_pid_start = 0U; | |
| } | |
| __HAL_LOCK(hpcd); | |
| (void)USB_ActivateEndpoint(hpcd->Instance, ep); | |
| __HAL_UNLOCK(hpcd); | |
| return ret; | |
| } | |
| /** | |
| * @brief Deactivate an endpoint. | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_Close(PCD_HandleTypeDef *hpcd, uint8_t ep_addr) | |
| { | |
| PCD_EPTypeDef *ep; | |
| if ((ep_addr & 0x80U) == 0x80U) | |
| { | |
| ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 1U; | |
| } | |
| else | |
| { | |
| ep = &hpcd->OUT_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 0U; | |
| } | |
| ep->num = ep_addr & EP_ADDR_MSK; | |
| __HAL_LOCK(hpcd); | |
| (void)USB_DeactivateEndpoint(hpcd->Instance, ep); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Receive an amount of data. | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @param pBuf pointer to the reception buffer | |
| * @param len amount of data to be received | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_Receive(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, uint8_t *pBuf, uint32_t len) | |
| { | |
| PCD_EPTypeDef *ep; | |
| ep = &hpcd->OUT_ep[ep_addr & EP_ADDR_MSK]; | |
| /*setup and start the Xfer */ | |
| ep->xfer_buff = pBuf; | |
| ep->xfer_len = len; | |
| ep->xfer_count = 0U; | |
| ep->is_in = 0U; | |
| ep->num = ep_addr & EP_ADDR_MSK; | |
| if (hpcd->Init.dma_enable == 1U) | |
| { | |
| ep->dma_addr = (uint32_t)pBuf; | |
| } | |
| (void)USB_EPStartXfer(hpcd->Instance, ep, (uint8_t)hpcd->Init.dma_enable); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Get Received Data Size | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @retval Data Size | |
| */ | |
| uint32_t HAL_PCD_EP_GetRxCount(PCD_HandleTypeDef const *hpcd, uint8_t ep_addr) | |
| { | |
| return hpcd->OUT_ep[ep_addr & EP_ADDR_MSK].xfer_count; | |
| } | |
| /** | |
| * @brief Send an amount of data | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @param pBuf pointer to the transmission buffer | |
| * @param len amount of data to be sent | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_Transmit(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, uint8_t *pBuf, uint32_t len) | |
| { | |
| PCD_EPTypeDef *ep; | |
| ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK]; | |
| /*setup and start the Xfer */ | |
| ep->xfer_buff = pBuf; | |
| ep->xfer_len = len; | |
| ep->xfer_count = 0U; | |
| ep->is_in = 1U; | |
| ep->num = ep_addr & EP_ADDR_MSK; | |
| if (hpcd->Init.dma_enable == 1U) | |
| { | |
| ep->dma_addr = (uint32_t)pBuf; | |
| } | |
| (void)USB_EPStartXfer(hpcd->Instance, ep, (uint8_t)hpcd->Init.dma_enable); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Set a STALL condition over an endpoint | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_SetStall(PCD_HandleTypeDef *hpcd, uint8_t ep_addr) | |
| { | |
| PCD_EPTypeDef *ep; | |
| if (((uint32_t)ep_addr & EP_ADDR_MSK) > hpcd->Init.dev_endpoints) | |
| { | |
| return HAL_ERROR; | |
| } | |
| if ((0x80U & ep_addr) == 0x80U) | |
| { | |
| ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 1U; | |
| } | |
| else | |
| { | |
| ep = &hpcd->OUT_ep[ep_addr]; | |
| ep->is_in = 0U; | |
| } | |
| ep->is_stall = 1U; | |
| ep->num = ep_addr & EP_ADDR_MSK; | |
| __HAL_LOCK(hpcd); | |
| (void)USB_EPSetStall(hpcd->Instance, ep); | |
| if ((ep_addr & EP_ADDR_MSK) == 0U) | |
| { | |
| (void)USB_EP0_OutStart(hpcd->Instance, (uint8_t)hpcd->Init.dma_enable, (uint8_t *)hpcd->Setup); | |
| } | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Clear a STALL condition over in an endpoint | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_ClrStall(PCD_HandleTypeDef *hpcd, uint8_t ep_addr) | |
| { | |
| PCD_EPTypeDef *ep; | |
| if (((uint32_t)ep_addr & 0x0FU) > hpcd->Init.dev_endpoints) | |
| { | |
| return HAL_ERROR; | |
| } | |
| if ((0x80U & ep_addr) == 0x80U) | |
| { | |
| ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 1U; | |
| } | |
| else | |
| { | |
| ep = &hpcd->OUT_ep[ep_addr & EP_ADDR_MSK]; | |
| ep->is_in = 0U; | |
| } | |
| ep->is_stall = 0U; | |
| ep->num = ep_addr & EP_ADDR_MSK; | |
| __HAL_LOCK(hpcd); | |
| (void)USB_EPClearStall(hpcd->Instance, ep); | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Abort an USB EP transaction. | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_Abort(PCD_HandleTypeDef *hpcd, uint8_t ep_addr) | |
| { | |
| HAL_StatusTypeDef ret; | |
| PCD_EPTypeDef *ep; | |
| if ((0x80U & ep_addr) == 0x80U) | |
| { | |
| ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK]; | |
| } | |
| else | |
| { | |
| ep = &hpcd->OUT_ep[ep_addr & EP_ADDR_MSK]; | |
| } | |
| /* Stop Xfer */ | |
| ret = USB_EPStopXfer(hpcd->Instance, ep); | |
| return ret; | |
| } | |
| /** | |
| * @brief Flush an endpoint | |
| * @param hpcd PCD handle | |
| * @param ep_addr endpoint address | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_EP_Flush(PCD_HandleTypeDef *hpcd, uint8_t ep_addr) | |
| { | |
| __HAL_LOCK(hpcd); | |
| if ((ep_addr & 0x80U) == 0x80U) | |
| { | |
| (void)USB_FlushTxFifo(hpcd->Instance, (uint32_t)ep_addr & EP_ADDR_MSK); | |
| } | |
| else | |
| { | |
| (void)USB_FlushRxFifo(hpcd->Instance); | |
| } | |
| __HAL_UNLOCK(hpcd); | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief Activate remote wakeup signalling | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_ActivateRemoteWakeup(PCD_HandleTypeDef *hpcd) | |
| { | |
| return (USB_ActivateRemoteWakeup(hpcd->Instance)); | |
| } | |
| /** | |
| * @brief De-activate remote wakeup signalling. | |
| * @param hpcd PCD handle | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_DeActivateRemoteWakeup(PCD_HandleTypeDef *hpcd) | |
| { | |
| return (USB_DeActivateRemoteWakeup(hpcd->Instance)); | |
| } | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup PCD_Exported_Functions_Group4 Peripheral State functions | |
| * @brief Peripheral State functions | |
| * | |
| @verbatim | |
| =============================================================================== | |
| ##### Peripheral State functions ##### | |
| =============================================================================== | |
| [..] | |
| This subsection permits to get in run-time the status of the peripheral | |
| and the data flow. | |
| @endverbatim | |
| * @{ | |
| */ | |
| /** | |
| * @brief Return the PCD handle state. | |
| * @param hpcd PCD handle | |
| * @retval HAL state | |
| */ | |
| PCD_StateTypeDef HAL_PCD_GetState(PCD_HandleTypeDef const *hpcd) | |
| { | |
| return hpcd->State; | |
| } | |
| #if defined (USB_OTG_FS) || defined (USB_OTG_HS) | |
| /** | |
| * @brief Set the USB Device high speed test mode. | |
| * @param hpcd PCD handle | |
| * @param testmode USB Device high speed test mode | |
| * @retval HAL status | |
| */ | |
| HAL_StatusTypeDef HAL_PCD_SetTestMode(const PCD_HandleTypeDef *hpcd, uint8_t testmode) | |
| { | |
| const USB_OTG_GlobalTypeDef *USBx = hpcd->Instance; | |
| uint32_t USBx_BASE = (uint32_t)USBx; | |
| switch (testmode) | |
| { | |
| case TEST_J: | |
| case TEST_K: | |
| case TEST_SE0_NAK: | |
| case TEST_PACKET: | |
| case TEST_FORCE_EN: | |
| USBx_DEVICE->DCTL |= (uint32_t)testmode << 4; | |
| break; | |
| default: | |
| break; | |
| } | |
| return HAL_OK; | |
| } | |
| #endif /* defined (USB_OTG_FS) || defined (USB_OTG_HS) */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /* Private functions ---------------------------------------------------------*/ | |
| /** @addtogroup PCD_Private_Functions | |
| * @{ | |
| */ | |
| #if defined (USB_OTG_FS) || defined (USB_OTG_HS) | |
| /** | |
| * @brief Check FIFO for the next packet to be loaded. | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval HAL status | |
| */ | |
| static HAL_StatusTypeDef PCD_WriteEmptyTxFifo(PCD_HandleTypeDef *hpcd, uint32_t epnum) | |
| { | |
| USB_OTG_GlobalTypeDef *USBx = hpcd->Instance; | |
| uint32_t USBx_BASE = (uint32_t)USBx; | |
| USB_OTG_EPTypeDef *ep; | |
| uint32_t len; | |
| uint32_t len32b; | |
| uint32_t fifoemptymsk; | |
| ep = &hpcd->IN_ep[epnum]; | |
| if (ep->xfer_count > ep->xfer_len) | |
| { | |
| return HAL_ERROR; | |
| } | |
| len = ep->xfer_len - ep->xfer_count; | |
| if (len > ep->maxpacket) | |
| { | |
| len = ep->maxpacket; | |
| } | |
| len32b = (len + 3U) / 4U; | |
| while (((USBx_INEP(epnum)->DTXFSTS & USB_OTG_DTXFSTS_INEPTFSAV) >= len32b) && | |
| (ep->xfer_count < ep->xfer_len) && (ep->xfer_len != 0U)) | |
| { | |
| /* Write the FIFO */ | |
| len = ep->xfer_len - ep->xfer_count; | |
| if (len > ep->maxpacket) | |
| { | |
| len = ep->maxpacket; | |
| } | |
| len32b = (len + 3U) / 4U; | |
| (void)USB_WritePacket(USBx, ep->xfer_buff, (uint8_t)epnum, (uint16_t)len, | |
| (uint8_t)hpcd->Init.dma_enable); | |
| ep->xfer_buff += len; | |
| ep->xfer_count += len; | |
| } | |
| if (ep->xfer_len <= ep->xfer_count) | |
| { | |
| fifoemptymsk = (uint32_t)(0x1UL << (epnum & EP_ADDR_MSK)); | |
| USBx_DEVICE->DIEPEMPMSK &= ~fifoemptymsk; | |
| } | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief process EP OUT transfer complete interrupt. | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval HAL status | |
| */ | |
| static HAL_StatusTypeDef PCD_EP_OutXfrComplete_int(PCD_HandleTypeDef *hpcd, uint32_t epnum) | |
| { | |
| USB_OTG_EPTypeDef *ep; | |
| const USB_OTG_GlobalTypeDef *USBx = hpcd->Instance; | |
| uint32_t USBx_BASE = (uint32_t)USBx; | |
| uint32_t gSNPSiD = *(__IO const uint32_t *)(&USBx->CID + 0x1U); | |
| uint32_t DoepintReg = USBx_OUTEP(epnum)->DOEPINT; | |
| if (hpcd->Init.dma_enable == 1U) | |
| { | |
| if ((DoepintReg & USB_OTG_DOEPINT_STUP) == USB_OTG_DOEPINT_STUP) /* Class C */ | |
| { | |
| /* StupPktRcvd = 1 this is a setup packet */ | |
| if ((gSNPSiD > USB_OTG_CORE_ID_300A) && | |
| ((DoepintReg & USB_OTG_DOEPINT_STPKTRX) == USB_OTG_DOEPINT_STPKTRX)) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_STPKTRX); | |
| } | |
| } | |
| else if ((DoepintReg & USB_OTG_DOEPINT_OTEPSPR) == USB_OTG_DOEPINT_OTEPSPR) /* Class E */ | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_OTEPSPR); | |
| } | |
| else if ((DoepintReg & (USB_OTG_DOEPINT_STUP | USB_OTG_DOEPINT_OTEPSPR)) == 0U) | |
| { | |
| /* StupPktRcvd = 1 this is a setup packet */ | |
| if ((gSNPSiD > USB_OTG_CORE_ID_300A) && | |
| ((DoepintReg & USB_OTG_DOEPINT_STPKTRX) == USB_OTG_DOEPINT_STPKTRX)) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_STPKTRX); | |
| } | |
| else | |
| { | |
| ep = &hpcd->OUT_ep[epnum]; | |
| /* out data packet received over EP */ | |
| ep->xfer_count = ep->xfer_size - (USBx_OUTEP(epnum)->DOEPTSIZ & USB_OTG_DOEPTSIZ_XFRSIZ); | |
| if (epnum == 0U) | |
| { | |
| if (ep->xfer_len == 0U) | |
| { | |
| /* this is ZLP, so prepare EP0 for next setup */ | |
| (void)USB_EP0_OutStart(hpcd->Instance, 1U, (uint8_t *)hpcd->Setup); | |
| } | |
| else | |
| { | |
| ep->xfer_buff += ep->xfer_count; | |
| } | |
| } | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->DataOutStageCallback(hpcd, (uint8_t)epnum); | |
| #else | |
| HAL_PCD_DataOutStageCallback(hpcd, (uint8_t)epnum); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| } | |
| else | |
| { | |
| /* ... */ | |
| } | |
| } | |
| else | |
| { | |
| if (gSNPSiD == USB_OTG_CORE_ID_310A) | |
| { | |
| /* StupPktRcvd = 1 this is a setup packet */ | |
| if ((DoepintReg & USB_OTG_DOEPINT_STPKTRX) == USB_OTG_DOEPINT_STPKTRX) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_STPKTRX); | |
| } | |
| else | |
| { | |
| if ((DoepintReg & USB_OTG_DOEPINT_OTEPSPR) == USB_OTG_DOEPINT_OTEPSPR) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_OTEPSPR); | |
| } | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->DataOutStageCallback(hpcd, (uint8_t)epnum); | |
| #else | |
| HAL_PCD_DataOutStageCallback(hpcd, (uint8_t)epnum); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| } | |
| else | |
| { | |
| if ((epnum == 0U) && (hpcd->OUT_ep[epnum].xfer_len == 0U)) | |
| { | |
| /* this is ZLP, so prepare EP0 for next setup */ | |
| (void)USB_EP0_OutStart(hpcd->Instance, 0U, (uint8_t *)hpcd->Setup); | |
| } | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->DataOutStageCallback(hpcd, (uint8_t)epnum); | |
| #else | |
| HAL_PCD_DataOutStageCallback(hpcd, (uint8_t)epnum); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| } | |
| } | |
| return HAL_OK; | |
| } | |
| /** | |
| * @brief process EP OUT setup packet received interrupt. | |
| * @param hpcd PCD handle | |
| * @param epnum endpoint number | |
| * @retval HAL status | |
| */ | |
| static HAL_StatusTypeDef PCD_EP_OutSetupPacket_int(PCD_HandleTypeDef *hpcd, uint32_t epnum) | |
| { | |
| const USB_OTG_GlobalTypeDef *USBx = hpcd->Instance; | |
| uint32_t USBx_BASE = (uint32_t)USBx; | |
| uint32_t gSNPSiD = *(__IO const uint32_t *)(&USBx->CID + 0x1U); | |
| uint32_t DoepintReg = USBx_OUTEP(epnum)->DOEPINT; | |
| if ((gSNPSiD > USB_OTG_CORE_ID_300A) && | |
| ((DoepintReg & USB_OTG_DOEPINT_STPKTRX) == USB_OTG_DOEPINT_STPKTRX)) | |
| { | |
| CLEAR_OUT_EP_INTR(epnum, USB_OTG_DOEPINT_STPKTRX); | |
| } | |
| /* Inform the upper layer that a setup packet is available */ | |
| #if (USE_HAL_PCD_REGISTER_CALLBACKS == 1U) | |
| hpcd->SetupStageCallback(hpcd); | |
| #else | |
| HAL_PCD_SetupStageCallback(hpcd); | |
| #endif /* USE_HAL_PCD_REGISTER_CALLBACKS */ | |
| if ((gSNPSiD > USB_OTG_CORE_ID_300A) && (hpcd->Init.dma_enable == 1U)) | |
| { | |
| (void)USB_EP0_OutStart(hpcd->Instance, 1U, (uint8_t *)hpcd->Setup); | |
| } | |
| return HAL_OK; | |
| } | |
| #endif /* defined (USB_OTG_FS) || defined (USB_OTG_HS) */ | |
| /** | |
| * @} | |
| */ | |
| #endif /* defined (USB_OTG_FS) || defined (USB_OTG_HS) */ | |
| #endif /* HAL_PCD_MODULE_ENABLED */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ |