/**
  ******************************************************************************
  * @file    stm32g0xx_ll_bus.h
  * @author  MCD Application Team
  * @brief   Header file of BUS LL module.

  @verbatim
                      ##### RCC Limitations #####
  ==============================================================================
    [..]
      A delay between an RCC peripheral clock enable and the effective peripheral
      enabling should be taken into account in order to manage the peripheral read/write
      from/to registers.
      (+) This delay depends on the peripheral mapping.
        (++) AHB & APB peripherals, 1 dummy read is necessary

    [..]
      Workarounds:
      (#) For AHB & APB peripherals, a dummy read to the peripheral register has been
          inserted in each LL_{BUS}_GRP{x}_EnableClock() function.

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2018 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32G0xx_LL_BUS_H
#define STM32G0xx_LL_BUS_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32g0xx.h"

/** @addtogroup STM32G0xx_LL_Driver
  * @{
  */

#if defined(RCC)

/** @defgroup BUS_LL BUS
  * @{
  */

/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/

/* Private constants ---------------------------------------------------------*/

/* Private macros ------------------------------------------------------------*/

/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup BUS_LL_Exported_Constants BUS Exported Constants
  * @{
  */

/** @defgroup BUS_LL_EC_AHB1_GRP1_PERIPH  AHB1 GRP1 PERIPH
  * @{
  */
#define LL_AHB1_GRP1_PERIPH_ALL            0xFFFFFFFFU
#define LL_AHB1_GRP1_PERIPH_DMA1           RCC_AHBENR_DMA1EN
#if defined(DMA2)
#define LL_AHB1_GRP1_PERIPH_DMA2           RCC_AHBENR_DMA2EN
#endif /* DMA2 */
#define LL_AHB1_GRP1_PERIPH_FLASH          RCC_AHBENR_FLASHEN
#define LL_AHB1_GRP1_PERIPH_SRAM           RCC_AHBSMENR_SRAMSMEN
#if defined(CRC)
#define LL_AHB1_GRP1_PERIPH_CRC            RCC_AHBENR_CRCEN
#endif /* CRC */
#if defined(AES)
#define LL_AHB1_GRP1_PERIPH_CRYP           RCC_AHBENR_AESEN
#endif /* AES */
#if defined(RNG)
#define LL_AHB1_GRP1_PERIPH_RNG            RCC_AHBENR_RNGEN
#endif /* RNG */
/**
  * @}
  */


/** @defgroup BUS_LL_EC_APB1_GRP1_PERIPH  APB1 GRP1 PERIPH
  * @{
  */
#define LL_APB1_GRP1_PERIPH_ALL            0xFFFFFFFFU
#if defined(TIM2)
#define LL_APB1_GRP1_PERIPH_TIM2           RCC_APBENR1_TIM2EN
#endif /* TIM2 */
#if defined(TIM3)
#define LL_APB1_GRP1_PERIPH_TIM3           RCC_APBENR1_TIM3EN
#endif /* TIM3 */
#if defined(TIM4)
#define LL_APB1_GRP1_PERIPH_TIM4           RCC_APBENR1_TIM4EN
#endif /* TIM4 */
#if defined(TIM6)
#define LL_APB1_GRP1_PERIPH_TIM6           RCC_APBENR1_TIM6EN
#endif /* TIM6 */
#if defined(TIM7)
#define LL_APB1_GRP1_PERIPH_TIM7           RCC_APBENR1_TIM7EN
#endif /* TIM7 */
#if defined(LPUART2)
#define LL_APB1_GRP1_PERIPH_LPUART2        RCC_APBENR1_LPUART2EN
#endif /* LPUART2 */
#if defined(USART5)
#define LL_APB1_GRP1_PERIPH_USART5         RCC_APBENR1_USART5EN
#endif /* USART5 */
#if defined(USART6)
#define LL_APB1_GRP1_PERIPH_USART6         RCC_APBENR1_USART6EN
#endif /* USART6 */
#define LL_APB1_GRP1_PERIPH_RTC            RCC_APBENR1_RTCAPBEN
#define LL_APB1_GRP1_PERIPH_WWDG           RCC_APBENR1_WWDGEN
#if defined(FDCAN1) || defined(FDCAN2)
#define LL_APB1_GRP1_PERIPH_FDCAN          RCC_APBENR1_FDCANEN
#endif /* FDCAN1 */
#if defined(USB_DRD_FS)
#define LL_APB1_GRP1_PERIPH_USB            RCC_APBENR1_USBEN
#endif /* USB_DRD_FS */
#define LL_APB1_GRP1_PERIPH_SPI2           RCC_APBENR1_SPI2EN
#if defined(SPI3)
#define LL_APB1_GRP1_PERIPH_SPI3           RCC_APBENR1_SPI3EN
#endif /* SPI3 */
#if defined(CRS)
#define LL_APB1_GRP1_PERIPH_CRS            RCC_APBENR1_CRSEN
#endif /* CRS */
#define LL_APB1_GRP1_PERIPH_USART2         RCC_APBENR1_USART2EN
#if defined(USART3)
#define LL_APB1_GRP1_PERIPH_USART3         RCC_APBENR1_USART3EN
#endif /* USART3 */
#if defined(USART4)
#define LL_APB1_GRP1_PERIPH_USART4         RCC_APBENR1_USART4EN
#endif /* USART4 */
#if defined(LPUART1)
#define LL_APB1_GRP1_PERIPH_LPUART1        RCC_APBENR1_LPUART1EN
#endif /* LPUART1 */
#define LL_APB1_GRP1_PERIPH_I2C1           RCC_APBENR1_I2C1EN
#define LL_APB1_GRP1_PERIPH_I2C2           RCC_APBENR1_I2C2EN
#if defined(I2C3)
#define LL_APB1_GRP1_PERIPH_I2C3           RCC_APBENR1_I2C3EN
#endif /* I2C3 */
#if defined(CEC)
#define LL_APB1_GRP1_PERIPH_CEC            RCC_APBENR1_CECEN
#endif /* CEC */
#if defined(UCPD1)
#define LL_APB1_GRP1_PERIPH_UCPD1          RCC_APBENR1_UCPD1EN
#endif /* UCPD1 */
#if defined(UCPD2)
#define LL_APB1_GRP1_PERIPH_UCPD2          RCC_APBENR1_UCPD2EN
#endif /* UCPD2 */
#define LL_APB1_GRP1_PERIPH_DBGMCU         RCC_APBENR1_DBGEN
#define LL_APB1_GRP1_PERIPH_PWR            RCC_APBENR1_PWREN
#if defined(DAC1)
#define LL_APB1_GRP1_PERIPH_DAC1           RCC_APBENR1_DAC1EN
#endif /* DAC1 */
#if defined(LPTIM2)
#define LL_APB1_GRP1_PERIPH_LPTIM2         RCC_APBENR1_LPTIM2EN
#endif /* LPTIM2 */
#if defined(LPTIM1)
#define LL_APB1_GRP1_PERIPH_LPTIM1         RCC_APBENR1_LPTIM1EN
#endif /* LPTIM1 */
/**
  * @}
  */

/** @defgroup BUS_LL_EC_APB2_GRP1_PERIPH  APB2 GRP1 PERIPH
  * @{
  */
#define LL_APB2_GRP1_PERIPH_ALL            0xFFFFFFFFU
#define LL_APB2_GRP1_PERIPH_SYSCFG         RCC_APBENR2_SYSCFGEN
#define LL_APB2_GRP1_PERIPH_TIM1           RCC_APBENR2_TIM1EN
#define LL_APB2_GRP1_PERIPH_SPI1           RCC_APBENR2_SPI1EN
#define LL_APB2_GRP1_PERIPH_USART1         RCC_APBENR2_USART1EN
#if defined(TIM14)
#define LL_APB2_GRP1_PERIPH_TIM14          RCC_APBENR2_TIM14EN
#endif /* TIM14 */
#if defined(TIM15)
#define LL_APB2_GRP1_PERIPH_TIM15          RCC_APBENR2_TIM15EN
#endif /* TIM15 */
#if defined(TIM16)
#define LL_APB2_GRP1_PERIPH_TIM16          RCC_APBENR2_TIM16EN
#endif /* TIM16 */
#if defined(TIM17)
#define LL_APB2_GRP1_PERIPH_TIM17          RCC_APBENR2_TIM17EN
#endif /* TIM17 */
#if defined(ADC)
#define LL_APB2_GRP1_PERIPH_ADC            RCC_APBENR2_ADCEN
#endif /* ADC */
/**
  * @}
  */

/** @defgroup BUS_LL_EC_IOP_GRP1_PERIPH  IOP GRP1 PERIPH
  * @{
  */
#define LL_IOP_GRP1_PERIPH_ALL             0xFFFFFFFFU
#define LL_IOP_GRP1_PERIPH_GPIOA           RCC_IOPENR_GPIOAEN
#define LL_IOP_GRP1_PERIPH_GPIOB           RCC_IOPENR_GPIOBEN
#define LL_IOP_GRP1_PERIPH_GPIOC           RCC_IOPENR_GPIOCEN
#define LL_IOP_GRP1_PERIPH_GPIOD           RCC_IOPENR_GPIODEN
#if defined(GPIOE)
#define LL_IOP_GRP1_PERIPH_GPIOE           RCC_IOPENR_GPIOEEN
#endif /* GPIOE */
#if defined(GPIOF)
#define LL_IOP_GRP1_PERIPH_GPIOF           RCC_IOPENR_GPIOFEN
#endif /* GPIOF */
/**
  * @}
  */

/**
  * @}
  */

/* Exported macro ------------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup BUS_LL_Exported_Functions BUS Exported Functions
  * @{
  */

/** @defgroup BUS_LL_EF_AHB1 AHB1
  * @{
  */

/**
  * @brief  Enable AHB1 peripherals clock.
  * @rmtoll AHBENR       DMA1EN        LL_AHB1_GRP1_EnableClock\n
  *         AHBENR       FLASHEN       LL_AHB1_GRP1_EnableClock\n
  *         AHBENR       CRCEN         LL_AHB1_GRP1_EnableClock\n
  *         AHBENR       AESEN         LL_AHB1_GRP1_EnableClock\n
  *         AHBENR       RNGEN         LL_AHB1_GRP1_EnableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval None
  */
__STATIC_INLINE void LL_AHB1_GRP1_EnableClock(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->AHBENR, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->AHBENR, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Check if AHB1 peripheral clock is enabled or not
  * @rmtoll AHBENR       DMA1EN        LL_AHB1_GRP1_IsEnabledClock\n
  *         AHBENR       FLASHEN       LL_AHB1_GRP1_IsEnabledClock\n
  *         AHBENR       CRCEN         LL_AHB1_GRP1_IsEnabledClock\n
  *         AHBENR       AESEN         LL_AHB1_GRP1_IsEnabledClock\n
  *         AHBENR       RNGEN         LL_AHB1_GRP1_IsEnabledClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval State of Periphs (1 or 0).
  */
__STATIC_INLINE uint32_t LL_AHB1_GRP1_IsEnabledClock(uint32_t Periphs)
{
  return ((READ_BIT(RCC->AHBENR, Periphs) == Periphs) ? 1UL : 0UL);
}

/**
  * @brief  Disable AHB1 peripherals clock.
  * @rmtoll AHBENR       DMA1EN        LL_AHB1_GRP1_DisableClock\n
  *         AHBENR       FLASHEN       LL_AHB1_GRP1_DisableClock\n
  *         AHBENR       CRCEN         LL_AHB1_GRP1_DisableClock\n
  *         AHBENR       AESEN         LL_AHB1_GRP1_DisableClock\n
  *         AHBENR       RNGEN         LL_AHB1_GRP1_DisableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval None
  */
__STATIC_INLINE void LL_AHB1_GRP1_DisableClock(uint32_t Periphs)
{
  CLEAR_BIT(RCC->AHBENR, Periphs);
}

/**
  * @brief  Force AHB1 peripherals reset.
  * @rmtoll AHBRSTR      DMA1RST       LL_AHB1_GRP1_ForceReset\n
  *         AHBRSTR      FLASHRST      LL_AHB1_GRP1_ForceReset\n
  *         AHBRSTR      CRCRST        LL_AHB1_GRP1_ForceReset\n
  *         AHBRSTR      AESRST        LL_AHB1_GRP1_ForceReset\n
  *         AHBRSTR      RNGRST        LL_AHB1_GRP1_ForceReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_ALL
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval None
  */
__STATIC_INLINE void LL_AHB1_GRP1_ForceReset(uint32_t Periphs)
{
  SET_BIT(RCC->AHBRSTR, Periphs);
}

/**
  * @brief  Release AHB1 peripherals reset.
  * @rmtoll AHBRSTR      DMA1RST       LL_AHB1_GRP1_ReleaseReset\n
  *         AHBRSTR      FLASHRST      LL_AHB1_GRP1_ReleaseReset\n
  *         AHBRSTR      CRCRST        LL_AHB1_GRP1_ReleaseReset\n
  *         AHBRSTR      AESRST        LL_AHB1_GRP1_ReleaseReset\n
  *         AHBRSTR      RNGRST        LL_AHB1_GRP1_ReleaseReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_ALL
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval None
  */
__STATIC_INLINE void LL_AHB1_GRP1_ReleaseReset(uint32_t Periphs)
{
  CLEAR_BIT(RCC->AHBRSTR, Periphs);
}

/**
  * @brief  Enable AHB1 peripheral clocks in Sleep and Stop modes
  * @rmtoll AHBSMENR     DMA1SMEN      LL_AHB1_GRP1_EnableClockStopSleep\n
  *         AHBSMENR     FLASHSMEN     LL_AHB1_GRP1_EnableClockStopSleep\n
  *         AHBSMENR     SRAMSMEN      LL_AHB1_GRP1_EnableClockStopSleep\n
  *         AHBSMENR     CRCSMEN       LL_AHB1_GRP1_EnableClockStopSleep\n
  *         AHBSMENR     AESSMEN       LL_AHB1_GRP1_EnableClockStopSleep\n
  *         AHBSMENR     RNGSMEN       LL_AHB1_GRP1_EnableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_SRAM
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval None
  */
__STATIC_INLINE void LL_AHB1_GRP1_EnableClockStopSleep(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->AHBSMENR, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->AHBSMENR, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Disable AHB1 peripheral clocks in Sleep and Stop modes
  * @rmtoll AHBSMENR     DMA1SMEN      LL_AHB1_GRP1_DisableClockStopSleep\n
  *         AHBSMENR     FLASHSMEN     LL_AHB1_GRP1_DisableClockStopSleep\n
  *         AHBSMENR     SRAMSMEN      LL_AHB1_GRP1_DisableClockStopSleep\n
  *         AHBSMENR     CRCSMEN       LL_AHB1_GRP1_DisableClockStopSleep\n
  *         AHBSMENR     AESSMEN       LL_AHB1_GRP1_DisableClockStopSleep\n
  *         AHBSMENR     RNGSMEN       LL_AHB1_GRP1_DisableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_AHB1_GRP1_PERIPH_DMA1
  *         @arg @ref LL_AHB1_GRP1_PERIPH_FLASH
  *         @arg @ref LL_AHB1_GRP1_PERIPH_SRAM
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRC
  *         @arg @ref LL_AHB1_GRP1_PERIPH_CRYP (*)
  *         @arg @ref LL_AHB1_GRP1_PERIPH_RNG  (*)
  * @note   (*) RNG & CRYP Peripherals available only on STM32G081xx
  * @retval None
  */
__STATIC_INLINE void LL_AHB1_GRP1_DisableClockStopSleep(uint32_t Periphs)
{
  CLEAR_BIT(RCC->AHBSMENR, Periphs);
}

/**
  * @}
  */

/** @defgroup BUS_LL_EF_APB1 APB1
  * @{
  */

/**
  * @brief  Enable APB1 peripherals clock.
  * @rmtoll APBENR1      TIM2EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      TIM3EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      TIM4EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      TIM6EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      TIM7EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      RTCAPBEN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      WWDGEN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      SPI2EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      SPI3EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      USART2EN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      USART3EN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      USART4EN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      USART5EN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      USART6EN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      LPUART1EN     LL_APB1_GRP1_EnableClock\n
  *         APBENR1      LPUART2EN     LL_APB1_GRP1_EnableClock\n
  *         APBENR1      I2C1EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      I2C2EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      I2C3EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      CECEN         LL_APB1_GRP1_EnableClock\n
  *         APBENR1      UCPD1EN       LL_APB1_GRP1_EnableClock\n
  *         APBENR1      UCPD2EN       LL_APB1_GRP1_EnableClock\n
  *         APBENR1      USBEN         LL_APB1_GRP1_EnableClock\n
  *         APBENR1      FDCANEN       LL_APB1_GRP1_EnableClock\n
  *         APBENR1      DBGEN         LL_APB1_GRP1_EnableClock\n
  *         APBENR1      PWREN         LL_APB1_GRP1_EnableClock\n
  *         APBENR1      DAC1EN        LL_APB1_GRP1_EnableClock\n
  *         APBENR1      LPTIM2EN      LL_APB1_GRP1_EnableClock\n
  *         APBENR1      LPTIM1EN      LL_APB1_GRP1_EnableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB1_GRP1_EnableClock(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->APBENR1, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->APBENR1, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Check if APB1 peripheral clock is enabled or not
  * @rmtoll APBENR1      TIM2EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      TIM3EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      TIM4EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      TIM6EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      TIM7EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      RTCAPBEN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      WWDGEN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      SPI2EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      SPI3EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      USART2EN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      USART3EN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      USART4EN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      USART5EN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      USART6EN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      LPUART1EN     LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      LPUART2EN     LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      I2C1EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      I2C2EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      I2C3EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      CECEN         LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      UCPD1EN       LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      UCPD2EN       LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      USBEN         LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      FDCANEN       LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      DBGEN         LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      PWREN         LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      DAC1EN        LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      LPTIM2EN      LL_APB1_GRP1_IsEnabledClock\n
  *         APBENR1      LPTIM1EN      LL_APB1_GRP1_IsEnabledClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval State of Periphs (1 or 0).
  */
__STATIC_INLINE uint32_t LL_APB1_GRP1_IsEnabledClock(uint32_t Periphs)
{
  return ((READ_BIT(RCC->APBENR1, Periphs) == (Periphs)) ? 1UL : 0UL);
}

/**
  * @brief  Disable APB1 peripherals clock.
  * @rmtoll APBENR1      TIM2EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      TIM3EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      TIM4EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      TIM6EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      TIM7EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      RTCAPBEN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      WWDGEN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      SPI2EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      SPI3EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      USART2EN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      USART3EN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      USART4EN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      USART5EN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      USART6EN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      LPUART1EN     LL_APB1_GRP1_DisableClock\n
  *         APBENR1      LPUART2EN     LL_APB1_GRP1_DisableClock\n
  *         APBENR1      I2C1EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      I2C2EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      I2C3EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      CECEN         LL_APB1_GRP1_DisableClock\n
  *         APBENR1      UCPD1EN       LL_APB1_GRP1_DisableClock\n
  *         APBENR1      UCPD2EN       LL_APB1_GRP1_DisableClock\n
  *         APBENR1      USBEN         LL_APB1_GRP1_DisableClock\n
  *         APBENR1      FDCANEN       LL_APB1_GRP1_DisableClock\n
  *         APBENR1      DBGEN         LL_APB1_GRP1_DisableClock\n
  *         APBENR1      PWREN         LL_APB1_GRP1_DisableClock\n
  *         APBENR1      DAC1EN        LL_APB1_GRP1_DisableClock\n
  *         APBENR1      LPTIM2EN      LL_APB1_GRP1_DisableClock\n
  *         APBENR1      LPTIM1EN      LL_APB1_GRP1_DisableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB1_GRP1_DisableClock(uint32_t Periphs)
{
  CLEAR_BIT(RCC->APBENR1, Periphs);
}

/**
  * @brief  Force APB1 peripherals reset.
  * @rmtoll APBRSTR1     TIM2RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     TIM3RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     TIM4RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     TIM6RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     TIM7RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     RTCRST        LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     WWDGRST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     SPI2RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     SPI3RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     USART2RST     LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     USART3RST     LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     USART4RST     LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     USART5RST     LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     USART6RST     LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     LPUART1RST    LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     LPUART2RST    LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     I2C1RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     I2C2RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     I2C3RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     CECRST        LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     UCPD1RST      LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     UCPD2RST      LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     USBRST        LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     FDCANRST      LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     DBGRST        LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     PWRRST        LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     DAC1RST       LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     LPTIM2RST     LL_APB1_GRP1_ForceReset\n
  *         APBRSTR1     LPTIM1RST     LL_APB1_GRP1_ForceReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB1_GRP1_ForceReset(uint32_t Periphs)
{
  SET_BIT(RCC->APBRSTR1, Periphs);
}

/**
  * @brief  Release APB1 peripherals reset.
  * @rmtoll APBRSTR1     TIM2RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     TIM4RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     TIM6RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     TIM7RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     RTCRST        LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     WWDGRST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     SPI2RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     SPI3RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     USART2RST     LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     USART3RST     LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     USART4RST     LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     USART5RST     LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     USART6RST     LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     LPUART1RST    LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     LPUART2RST    LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     I2C1RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     I2C2RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     I2C3RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     CECRST        LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     UCPD1RST      LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     UCPD2RST      LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     USBRST        LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     FDCANRST      LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     DBGRST        LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     PWRRST        LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     DAC1RST       LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     LPTIM2RST     LL_APB1_GRP1_ReleaseReset\n
  *         APBRSTR1     LPTIM1RST     LL_APB1_GRP1_ReleaseReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB1_GRP1_ReleaseReset(uint32_t Periphs)
{
  CLEAR_BIT(RCC->APBRSTR1, Periphs);
}

/**
  * @brief  Enable APB1 peripheral clocks in Sleep and Stop modes
  * @rmtoll APBSMENR1    TIM2SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    TIM3SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    TIM4SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    TIM6SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    TIM7SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    RTCAPBSMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    WWDGSMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    SPI2SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    SPI3SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    USART2SMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    USART3SMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    USART4SMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    USART5SMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    USART6SMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    LPUART1SMEN   LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    LPUART2SMEN   LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    I2C1SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    I2C2SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    I2C3SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    CECSMEN       LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    UCPD1SMEN     LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    UCPD2SMEN     LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    USBSMEN       LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    FDCANSMEN     LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    DBGSMEN       LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    PWRSMEN       LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    DAC1SMEN      LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    LPTIM2SMEN    LL_APB1_GRP1_EnableClockStopSleep\n
  *         APBSMENR1    LPTIM1SMEN    LL_APB1_GRP1_EnableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB1_GRP1_EnableClockStopSleep(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->APBSMENR1, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->APBSMENR1, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Disable APB1 peripheral clocks in Sleep and Stop modes
  * @rmtoll APBSMENR1    TIM2SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    TIM3SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    TIM'SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    TIM6SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    TIM7SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    RTCAPBSMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    WWDGSMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    SPI2SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    SPI3SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    USART2SMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    USART3SMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    USART4SMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    USART5SMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    USART6SMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    LPUART1SMEN   LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    LPUART2SMEN   LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    I2C1SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    I2C2SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    I2C3SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    CECSMEN       LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    UCPD1SMEN     LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    UCPD2SMEN     LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    USBSMEN       LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    FSCANSMEN     LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    DBGSMEN       LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    PWRSMEN       LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    DAC1SMEN      LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    LPTIM2SMEN    LL_APB1_GRP1_DisableClockStopSleep\n
  *         APBSMENR1    LPTIM1SMEN    LL_APB1_GRP1_DisableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM2    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM3
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM4    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM6    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_TIM7    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_RTC
  *         @arg @ref LL_APB1_GRP1_PERIPH_WWDG
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI2
  *         @arg @ref LL_APB1_GRP1_PERIPH_SPI3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART2
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART3  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART4  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART5  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USART6  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART1 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPUART2 (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C1
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C2
  *         @arg @ref LL_APB1_GRP1_PERIPH_I2C3    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_CEC     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD1   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_UCPD2   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_USB     (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_FDCAN   (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_DBGMCU
  *         @arg @ref LL_APB1_GRP1_PERIPH_PWR
  *         @arg @ref LL_APB1_GRP1_PERIPH_DAC1    (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM2  (1)
  *         @arg @ref LL_APB1_GRP1_PERIPH_LPTIM1  (1)
  * @note Peripheral marked with (1) are not available all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB1_GRP1_DisableClockStopSleep(uint32_t Periphs)
{
  CLEAR_BIT(RCC->APBSMENR1, Periphs);
}

/**
  * @}
  */

/** @defgroup BUS_LL_EF_APB2 APB2
  * @{
  */

/**
  * @brief  Enable APB2 peripherals clock.
  * @rmtoll APBENR2      SYSCFGEN      LL_APB2_GRP1_EnableClock\n
  *         APBENR2      TIM1EN        LL_APB2_GRP1_EnableClock\n
  *         APBENR2      SPI1EN        LL_APB2_GRP1_EnableClock\n
  *         APBENR2      USART1EN      LL_APB2_GRP1_EnableClock\n
  *         APBENR2      TIM14EN       LL_APB2_GRP1_EnableClock\n
  *         APBENR2      TIM15EN       LL_APB2_GRP1_EnableClock\n
  *         APBENR2      TIM16EN       LL_APB2_GRP1_EnableClock\n
  *         APBENR2      TIM17EN       LL_APB2_GRP1_EnableClock\n
  *         APBENR2      ADCEN         LL_APB2_GRP1_EnableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB2_GRP1_EnableClock(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->APBENR2, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->APBENR2, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Check if APB2 peripheral clock is enabled or not
  * @rmtoll APBENR2      SYSCFGEN      LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      TIM1EN        LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      SPI1EN        LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      USART1EN      LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      TIM14EN       LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      TIM15EN       LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      TIM16EN       LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      TIM17EN       LL_APB2_GRP1_IsEnabledClock\n
  *         APBENR2      ADCEN         LL_APB2_GRP1_IsEnabledClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval State of Periphs (1 or 0).
  */
__STATIC_INLINE uint32_t LL_APB2_GRP1_IsEnabledClock(uint32_t Periphs)
{
  return ((READ_BIT(RCC->APBENR2, Periphs) == (Periphs)) ? 1UL : 0UL);
}

/**
  * @brief  Disable APB2 peripherals clock.
  * @rmtoll APBENR2      SYSCFGEN      LL_APB2_GRP1_DisableClock\n
  *         APBENR2      TIM1EN        LL_APB2_GRP1_DisableClock\n
  *         APBENR2      SPI1EN        LL_APB2_GRP1_DisableClock\n
  *         APBENR2      USART1EN      LL_APB2_GRP1_DisableClock\n
  *         APBENR2      TIM14EN       LL_APB2_GRP1_DisableClock\n
  *         APBENR2      TIM15EN       LL_APB2_GRP1_DisableClock\n
  *         APBENR2      TIM16EN       LL_APB2_GRP1_DisableClock\n
  *         APBENR2      TIM17EN       LL_APB2_GRP1_DisableClock\n
  *         APBENR2      ADCEN         LL_APB2_GRP1_DisableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB2_GRP1_DisableClock(uint32_t Periphs)
{
  CLEAR_BIT(RCC->APBENR2, Periphs);
}

/**
  * @brief  Force APB2 peripherals reset.
  * @rmtoll APBRSTR2     SYSCFGRST     LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     TIM1RST       LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     SPI1RST       LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     USART1RST     LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     TIM14RST      LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     TIM15RST      LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     TIM16RST      LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     TIM17RST      LL_APB2_GRP1_ForceReset\n
  *         APBRSTR2     ADCRST        LL_APB2_GRP1_ForceReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_ALL
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB2_GRP1_ForceReset(uint32_t Periphs)
{
  SET_BIT(RCC->APBRSTR2, Periphs);
}

/**
  * @brief  Release APB2 peripherals reset.
  * @rmtoll APBRSTR2     SYSCFGRST     LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     TIM1RST       LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     SPI1RST       LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     USART1RST     LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     TIM14RST      LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     TIM15RST      LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     TIM16RST      LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     TIM17RST      LL_APB2_GRP1_ReleaseReset\n
  *         APBRSTR2     ADCRST        LL_APB2_GRP1_ReleaseReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_ALL
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB2_GRP1_ReleaseReset(uint32_t Periphs)
{
  CLEAR_BIT(RCC->APBRSTR2, Periphs);
}

/**
  * @brief  Enable APB2 peripheral clocks in Sleep and Stop modes
  * @rmtoll APBSMENR2    SYSCFGSMEN    LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    TIM1SMEN      LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    SPI1SMEN      LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    USART1SMEN    LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    TIM14SMEN     LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    TIM15SMEN     LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    TIM16SMEN     LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    TIM17SMEN     LL_APB2_GRP1_EnableClockStopSleep\n
  *         APBSMENR2    ADCSMEN       LL_APB2_GRP1_EnableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB2_GRP1_EnableClockStopSleep(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->APBSMENR2, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->APBSMENR2, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Disable APB2 peripheral clocks in Sleep and Stop modes
  * @rmtoll APBSMENR2    SYSCFGSMEN    LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    TIM1SMEN      LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    SPI1SMEN      LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    USART1SMEN    LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    TIM14SMEN     LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    TIM15SMEN     LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    TIM16SMEN     LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    TIM17SMEN     LL_APB2_GRP1_DisableClockStopSleep\n
  *         APBSMENR2    ADCSMEN       LL_APB2_GRP1_DisableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_APB2_GRP1_PERIPH_SYSCFG
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM1
  *         @arg @ref LL_APB2_GRP1_PERIPH_SPI1
  *         @arg @ref LL_APB2_GRP1_PERIPH_USART1
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM14
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM15 (*)
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM16
  *         @arg @ref LL_APB2_GRP1_PERIPH_TIM17
  *         @arg @ref LL_APB2_GRP1_PERIPH_ADC
  * @note (*) peripheral not available on all devices
  * @retval None
  */
__STATIC_INLINE void LL_APB2_GRP1_DisableClockStopSleep(uint32_t Periphs)
{
  CLEAR_BIT(RCC->APBSMENR2, Periphs);
}

/**
  * @}
  */

/** @defgroup BUS_LL_EF_IOP IOP
  * @{
  */

/**
  * @brief  Enable IOP peripherals clock.
  * @rmtoll IOPENR       GPIOAEN       LL_IOP_GRP1_EnableClock\n
  *         IOPENR       GPIOBEN       LL_IOP_GRP1_EnableClock\n
  *         IOPENR       GPIOCEN       LL_IOP_GRP1_EnableClock\n
  *         IOPENR       GPIODEN       LL_IOP_GRP1_EnableClock\n
  *         IOPENR       GPIOEEN       LL_IOP_GRP1_EnableClock\n
  *         IOPENR       GPIOFEN       LL_IOP_GRP1_EnableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval None
  */
__STATIC_INLINE void LL_IOP_GRP1_EnableClock(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->IOPENR, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->IOPENR, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Check if IOP peripheral clock is enabled or not
  * @rmtoll IOPENR       GPIOAEN       LL_IOP_GRP1_IsEnabledClock\n
  *         IOPENR       GPIOBEN       LL_IOP_GRP1_IsEnabledClock\n
  *         IOPENR       GPIOCEN       LL_IOP_GRP1_IsEnabledClock\n
  *         IOPENR       GPIODEN       LL_IOP_GRP1_IsEnabledClock\n
  *         IOPENR       GPIOEEN       LL_IOP_GRP1_IsEnabledClock\n
  *         IOPENR       GPIOFEN       LL_IOP_GRP1_IsEnabledClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval State of Periphs (1 or 0).
  */
__STATIC_INLINE uint32_t LL_IOP_GRP1_IsEnabledClock(uint32_t Periphs)
{
  return ((READ_BIT(RCC->IOPENR, Periphs) == Periphs) ? 1UL : 0UL);
}

/**
  * @brief  Disable IOP peripherals clock.
  * @rmtoll IOPENR       GPIOAEN       LL_IOP_GRP1_DisableClock\n
  *         IOPENR       GPIOBEN       LL_IOP_GRP1_DisableClock\n
  *         IOPENR       GPIOCEN       LL_IOP_GRP1_DisableClock\n
  *         IOPENR       GPIODEN       LL_IOP_GRP1_DisableClock\n
  *         IOPENR       GPIOEEN       LL_IOP_GRP1_DisableClock\n
  *         IOPENR       GPIOFEN       LL_IOP_GRP1_DisableClock
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval None
  */
__STATIC_INLINE void LL_IOP_GRP1_DisableClock(uint32_t Periphs)
{
  CLEAR_BIT(RCC->IOPENR, Periphs);
}

/**
  * @brief  Disable IOP peripherals clock.
  * @rmtoll IOPRSTR      GPIOARST      LL_IOP_GRP1_ForceReset\n
  *         IOPRSTR      GPIOBRST      LL_IOP_GRP1_ForceReset\n
  *         IOPRSTR      GPIOCRST      LL_IOP_GRP1_ForceReset\n
  *         IOPRSTR      GPIODRST      LL_IOP_GRP1_ForceReset\n
  *         IOPRSTR      GPIOERST      LL_IOP_GRP1_ForceReset\n
  *         IOPRSTR      GPIOFRST      LL_IOP_GRP1_ForceReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_ALL
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval None
  */
__STATIC_INLINE void LL_IOP_GRP1_ForceReset(uint32_t Periphs)
{
  SET_BIT(RCC->IOPRSTR, Periphs);
}

/**
  * @brief  Release IOP peripherals reset.
  * @rmtoll IOPRSTR      GPIOARST      LL_IOP_GRP1_ReleaseReset\n
  *         IOPRSTR      GPIOBRST      LL_IOP_GRP1_ReleaseReset\n
  *         IOPRSTR      GPIOCRST      LL_IOP_GRP1_ReleaseReset\n
  *         IOPRSTR      GPIODRST      LL_IOP_GRP1_ReleaseReset\n
  *         IOPRSTR      GPIOERST      LL_IOP_GRP1_ReleaseReset\n
  *         IOPRSTR      GPIOFRST      LL_IOP_GRP1_ReleaseReset
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_ALL
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval None
  */
__STATIC_INLINE void LL_IOP_GRP1_ReleaseReset(uint32_t Periphs)
{
  CLEAR_BIT(RCC->IOPRSTR, Periphs);
}

/**
  * @brief  Enable IOP peripheral clocks in Sleep and Stop modes
  * @rmtoll IOPSMENR     GPIOASMEN     LL_IOP_GRP1_EnableClockStopSleep\n
  *         IOPSMENR     GPIOBSMEN     LL_IOP_GRP1_EnableClockStopSleep\n
  *         IOPSMENR     GPIOCSMEN     LL_IOP_GRP1_EnableClockStopSleep\n
  *         IOPSMENR     GPIODSMEN     LL_IOP_GRP1_EnableClockStopSleep\n
  *         IOPSMENR     GPIOESMEN     LL_IOP_GRP1_EnableClockStopSleep\n
  *         IOPSMENR     GPIOFSMEN     LL_IOP_GRP1_EnableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval None
  */
__STATIC_INLINE void LL_IOP_GRP1_EnableClockStopSleep(uint32_t Periphs)
{
  __IO uint32_t tmpreg;
  SET_BIT(RCC->IOPSMENR, Periphs);
  /* Delay after an RCC peripheral clock enabling */
  tmpreg = READ_BIT(RCC->IOPSMENR, Periphs);
  (void)tmpreg;
}

/**
  * @brief  Disable IOP peripheral clocks in Sleep and Stop modes
  * @rmtoll IOPSMENR     GPIOASMEN     LL_IOP_GRP1_DisableClockStopSleep\n
  *         IOPSMENR     GPIOBSMEN     LL_IOP_GRP1_DisableClockStopSleep\n
  *         IOPSMENR     GPIOCSMEN     LL_IOP_GRP1_DisableClockStopSleep\n
  *         IOPSMENR     GPIODSMEN     LL_IOP_GRP1_DisableClockStopSleep\n
  *         IOPSMENR     GPIOESMEN     LL_IOP_GRP1_DisableClockStopSleep\n
  *         IOPSMENR     GPIOFSMEN     LL_IOP_GRP1_DisableClockStopSleep
  * @param  Periphs This parameter can be a combination of the following values:
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOA
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOB
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOC
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOD
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOE
  *         @arg @ref LL_IOP_GRP1_PERIPH_GPIOF
  * @retval None
  */
__STATIC_INLINE void LL_IOP_GRP1_DisableClockStopSleep(uint32_t Periphs)
{
  CLEAR_BIT(RCC->IOPSMENR, Periphs);
}

/**
  * @}
  */


/**
  * @}
  */

/**
  * @}
  */

#endif /* RCC */

/**
  * @}
  */

#ifdef __cplusplus
}
#endif

#endif /* STM32G0xx_LL_BUS_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/