| /** |
| ****************************************************************************** |
| * @file stm32g4xx_hal_pwr_ex.h |
| * @author MCD Application Team |
| * @brief Header file of PWR HAL Extended module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2019 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32G4xx_HAL_PWR_EX_H |
| #define STM32G4xx_HAL_PWR_EX_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32g4xx_hal_def.h" |
| |
| /** @addtogroup STM32G4xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup PWREx |
| * @{ |
| */ |
| |
| |
| /* Exported types ------------------------------------------------------------*/ |
| |
| /** @defgroup PWREx_Exported_Types PWR Extended Exported Types |
| * @{ |
| */ |
| |
| |
| /** |
| * @brief PWR PVM configuration structure definition |
| */ |
| typedef struct |
| { |
| uint32_t PVMType; /*!< PVMType: Specifies which voltage is monitored and against which threshold. |
| This parameter can be a value of @ref PWREx_PVM_Type. */ |
| uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins. |
| This parameter can be a value of @ref PWREx_PVM_Mode. */ |
| }PWR_PVMTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| |
| /** @defgroup PWREx_Exported_Constants PWR Extended Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup PWREx_WUP_Polarity Shift to apply to retrieve polarity information from PWR_WAKEUP_PINy_xxx constants |
| * @{ |
| */ |
| #define PWR_WUP_POLARITY_SHIFT 0x05U /*!< Internal constant used to retrieve wakeup pin polariry */ |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup PWREx_WakeUp_Pins PWR wake-up pins |
| * @{ |
| */ |
| #define PWR_WAKEUP_PIN1 PWR_CR3_EWUP1 /*!< Wakeup pin 1 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN2 PWR_CR3_EWUP2 /*!< Wakeup pin 2 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN3 PWR_CR3_EWUP3 /*!< Wakeup pin 3 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN4 PWR_CR3_EWUP4 /*!< Wakeup pin 4 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN5 PWR_CR3_EWUP5 /*!< Wakeup pin 5 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN1_HIGH PWR_CR3_EWUP1 /*!< Wakeup pin 1 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN2_HIGH PWR_CR3_EWUP2 /*!< Wakeup pin 2 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN3_HIGH PWR_CR3_EWUP3 /*!< Wakeup pin 3 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN4_HIGH PWR_CR3_EWUP4 /*!< Wakeup pin 4 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN5_HIGH PWR_CR3_EWUP5 /*!< Wakeup pin 5 (with high level polarity) */ |
| #define PWR_WAKEUP_PIN1_LOW (uint32_t)((PWR_CR4_WP1<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP1) /*!< Wakeup pin 1 (with low level polarity) */ |
| #define PWR_WAKEUP_PIN2_LOW (uint32_t)((PWR_CR4_WP2<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP2) /*!< Wakeup pin 2 (with low level polarity) */ |
| #define PWR_WAKEUP_PIN3_LOW (uint32_t)((PWR_CR4_WP3<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP3) /*!< Wakeup pin 3 (with low level polarity) */ |
| #define PWR_WAKEUP_PIN4_LOW (uint32_t)((PWR_CR4_WP4<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP4) /*!< Wakeup pin 4 (with low level polarity) */ |
| #define PWR_WAKEUP_PIN5_LOW (uint32_t)((PWR_CR4_WP5<<PWR_WUP_POLARITY_SHIFT) | PWR_CR3_EWUP5) /*!< Wakeup pin 5 (with low level polarity) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_PVM_Type Peripheral Voltage Monitoring type |
| * @{ |
| */ |
| #if defined(PWR_CR2_PVME1) |
| #define PWR_PVM_1 PWR_CR2_PVME1 /*!< Peripheral Voltage Monitoring 1 enable: VDDUSB versus 1.2 V (applicable when USB feature is supported) */ |
| #endif /* PWR_CR2_PVME1 */ |
| #if defined(PWR_CR2_PVME2) |
| #define PWR_PVM_2 PWR_CR2_PVME2 /*!< Peripheral Voltage Monitoring 2 enable: VDDIO2 versus 0.9 V (applicable when VDDIO2 is present on device) */ |
| #endif /* PWR_CR2_PVME2 */ |
| #define PWR_PVM_3 PWR_CR2_PVME3 /*!< Peripheral Voltage Monitoring 3 enable: VDDA versus 1.62 V */ |
| #define PWR_PVM_4 PWR_CR2_PVME4 /*!< Peripheral Voltage Monitoring 4 enable: VDDA versus 2.2 V */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_PVM_Mode PWR PVM interrupt and event mode |
| * @{ |
| */ |
| #define PWR_PVM_MODE_NORMAL 0x00000000U /*!< basic mode is used */ |
| #define PWR_PVM_MODE_IT_RISING 0x00010001U /*!< External Interrupt Mode with Rising edge trigger detection */ |
| #define PWR_PVM_MODE_IT_FALLING 0x00010002U /*!< External Interrupt Mode with Falling edge trigger detection */ |
| #define PWR_PVM_MODE_IT_RISING_FALLING 0x00010003U /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ |
| #define PWR_PVM_MODE_EVENT_RISING 0x00020001U /*!< Event Mode with Rising edge trigger detection */ |
| #define PWR_PVM_MODE_EVENT_FALLING 0x00020002U /*!< Event Mode with Falling edge trigger detection */ |
| #define PWR_PVM_MODE_EVENT_RISING_FALLING 0x00020003U /*!< Event Mode with Rising/Falling edge trigger detection */ |
| /** |
| * @} |
| */ |
| |
| |
| |
| /** @defgroup PWREx_Regulator_Voltage_Scale PWR Regulator voltage scale |
| * @{ |
| */ |
| #if defined(PWR_CR5_R1MODE) |
| #define PWR_REGULATOR_VOLTAGE_SCALE1_BOOST ((uint32_t)0x00000000) /*!< Voltage scaling range 1 boost mode */ |
| #endif /*PWR_CR5_R1MODE */ |
| #define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR1_VOS_0 /*!< Voltage scaling range 1 normal mode */ |
| #define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR1_VOS_1 /*!< Voltage scaling range 2 */ |
| /** |
| * @} |
| */ |
| |
| |
| /** @defgroup PWREx_VBAT_Battery_Charging_Selection PWR battery charging resistor selection |
| * @{ |
| */ |
| #define PWR_BATTERY_CHARGING_RESISTOR_5 0x00000000U /*!< VBAT charging through a 5 kOhms resistor */ |
| #define PWR_BATTERY_CHARGING_RESISTOR_1_5 PWR_CR4_VBRS /*!< VBAT charging through a 1.5 kOhms resistor */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_VBAT_Battery_Charging PWR battery charging |
| * @{ |
| */ |
| #define PWR_BATTERY_CHARGING_DISABLE 0x00000000U |
| #define PWR_BATTERY_CHARGING_ENABLE PWR_CR4_VBE |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_GPIO_Bit_Number GPIO bit number for I/O setting in standby/shutdown mode |
| * @{ |
| */ |
| #define PWR_GPIO_BIT_0 PWR_PUCRA_PA0 /*!< GPIO port I/O pin 0 */ |
| #define PWR_GPIO_BIT_1 PWR_PUCRA_PA1 /*!< GPIO port I/O pin 1 */ |
| #define PWR_GPIO_BIT_2 PWR_PUCRA_PA2 /*!< GPIO port I/O pin 2 */ |
| #define PWR_GPIO_BIT_3 PWR_PUCRA_PA3 /*!< GPIO port I/O pin 3 */ |
| #define PWR_GPIO_BIT_4 PWR_PUCRA_PA4 /*!< GPIO port I/O pin 4 */ |
| #define PWR_GPIO_BIT_5 PWR_PUCRA_PA5 /*!< GPIO port I/O pin 5 */ |
| #define PWR_GPIO_BIT_6 PWR_PUCRA_PA6 /*!< GPIO port I/O pin 6 */ |
| #define PWR_GPIO_BIT_7 PWR_PUCRA_PA7 /*!< GPIO port I/O pin 7 */ |
| #define PWR_GPIO_BIT_8 PWR_PUCRA_PA8 /*!< GPIO port I/O pin 8 */ |
| #define PWR_GPIO_BIT_9 PWR_PUCRA_PA9 /*!< GPIO port I/O pin 9 */ |
| #define PWR_GPIO_BIT_10 PWR_PUCRA_PA10 /*!< GPIO port I/O pin 10 */ |
| #define PWR_GPIO_BIT_11 PWR_PUCRA_PA11 /*!< GPIO port I/O pin 11 */ |
| #define PWR_GPIO_BIT_12 PWR_PUCRA_PA12 /*!< GPIO port I/O pin 12 */ |
| #define PWR_GPIO_BIT_13 PWR_PUCRA_PA13 /*!< GPIO port I/O pin 13 */ |
| #define PWR_GPIO_BIT_14 PWR_PDCRA_PA14 /*!< GPIO port I/O pin 14 */ |
| #define PWR_GPIO_BIT_15 PWR_PUCRA_PA15 /*!< GPIO port I/O pin 15 */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_GPIO GPIO port |
| * @{ |
| */ |
| #define PWR_GPIO_A 0x00000000U /*!< GPIO port A */ |
| #define PWR_GPIO_B 0x00000001U /*!< GPIO port B */ |
| #define PWR_GPIO_C 0x00000002U /*!< GPIO port C */ |
| #define PWR_GPIO_D 0x00000003U /*!< GPIO port D */ |
| #define PWR_GPIO_E 0x00000004U /*!< GPIO port E */ |
| #define PWR_GPIO_F 0x00000005U /*!< GPIO port F */ |
| #define PWR_GPIO_G 0x00000006U /*!< GPIO port G */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_PVM_EXTI_LINE PWR PVM external interrupts lines |
| * @{ |
| */ |
| #if defined(PWR_CR2_PVME1) |
| #define PWR_EXTI_LINE_PVM1 0x00000008U /*!< External interrupt line 35 Connected to the PVM1 EXTI Line */ |
| #endif /* PWR_CR2_PVME1 */ |
| #if defined(PWR_CR2_PVME2) |
| #define PWR_EXTI_LINE_PVM2 0x00000010U /*!< External interrupt line 36 Connected to the PVM2 EXTI Line */ |
| #endif /* PWR_CR2_PVME2 */ |
| #define PWR_EXTI_LINE_PVM3 0x00000020U /*!< External interrupt line 37 Connected to the PVM3 EXTI Line */ |
| #define PWR_EXTI_LINE_PVM4 0x00000040U /*!< External interrupt line 38 Connected to the PVM4 EXTI Line */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_PVM_EVENT_LINE PWR PVM event lines |
| * @{ |
| */ |
| #if defined(PWR_CR2_PVME1) |
| #define PWR_EVENT_LINE_PVM1 0x00000008U /*!< Event line 35 Connected to the PVM1 EXTI Line */ |
| #endif /* PWR_CR2_PVME1 */ |
| #if defined(PWR_CR2_PVME2) |
| #define PWR_EVENT_LINE_PVM2 0x00000010U /*!< Event line 36 Connected to the PVM2 EXTI Line */ |
| #endif /* PWR_CR2_PVME2 */ |
| #define PWR_EVENT_LINE_PVM3 0x00000020U /*!< Event line 37 Connected to the PVM3 EXTI Line */ |
| #define PWR_EVENT_LINE_PVM4 0x00000040U /*!< Event line 38 Connected to the PVM4 EXTI Line */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup PWREx_Flag PWR Status Flags |
| * Elements values convention: 0000 0000 0XXY YYYYb |
| * - Y YYYY : Flag position in the XX register (5 bits) |
| * - XX : Status register (2 bits) |
| * - 01: SR1 register |
| * - 10: SR2 register |
| * The only exception is PWR_FLAG_WU, encompassing all |
| * wake-up flags and set to PWR_SR1_WUF. |
| * @{ |
| */ |
| #define PWR_FLAG_WUF1 0x0020U /*!< Wakeup event on wakeup pin 1 */ |
| #define PWR_FLAG_WUF2 0x0021U /*!< Wakeup event on wakeup pin 2 */ |
| #define PWR_FLAG_WUF3 0x0022U /*!< Wakeup event on wakeup pin 3 */ |
| #define PWR_FLAG_WUF4 0x0023U /*!< Wakeup event on wakeup pin 4 */ |
| #define PWR_FLAG_WUF5 0x0024U /*!< Wakeup event on wakeup pin 5 */ |
| #define PWR_FLAG_WU PWR_SR1_WUF /*!< Encompass wakeup event on all wakeup pins */ |
| #define PWR_FLAG_SB 0x0028U /*!< Standby flag */ |
| #define PWR_FLAG_WUFI 0x002FU /*!< Wakeup on internal wakeup line */ |
| |
| #define PWR_FLAG_REGLPS 0x0048U /*!< Low-power regulator start flag */ |
| #define PWR_FLAG_REGLPF 0x0049U /*!< Low-power regulator flag */ |
| #define PWR_FLAG_VOSF 0x004AU /*!< Voltage scaling flag */ |
| #define PWR_FLAG_PVDO 0x004BU /*!< Power Voltage Detector output flag */ |
| #if defined(PWR_CR2_PVME1) |
| #define PWR_FLAG_PVMO1 0x004CU /*!< Power Voltage Monitoring 1 output flag */ |
| #endif /* PWR_CR2_PVME1 */ |
| #if defined(PWR_CR2_PVME2) |
| #define PWR_FLAG_PVMO2 0x004DU /*!< Power Voltage Monitoring 2 output flag */ |
| #endif /* PWR_CR2_PVME2 */ |
| #define PWR_FLAG_PVMO3 0x004EU /*!< Power Voltage Monitoring 3 output flag */ |
| #define PWR_FLAG_PVMO4 0x004FU /*!< Power Voltage Monitoring 4 output flag */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup PWREx_Exported_Macros PWR Extended Exported Macros |
| * @{ |
| */ |
| |
| #if defined(PWR_CR2_PVME1) |
| /** |
| * @brief Enable the PVM1 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM1) |
| |
| /** |
| * @brief Disable the PVM1 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM1) |
| |
| /** |
| * @brief Enable the PVM1 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM1) |
| |
| /** |
| * @brief Disable the PVM1 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM1) |
| |
| /** |
| * @brief Enable the PVM1 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM1) |
| |
| /** |
| * @brief Disable the PVM1 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM1) |
| |
| /** |
| * @brief Enable the PVM1 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM1) |
| |
| |
| /** |
| * @brief Disable the PVM1 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM1) |
| |
| |
| /** |
| * @brief PVM1 EXTI line configuration: set rising & falling edge trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_ENABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM1_EXTI_ENABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM1_EXTI_ENABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Disable the PVM1 Extended Interrupt Rising & Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_DISABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM1_EXTI_DISABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM1_EXTI_DISABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Generate a Software interrupt on selected EXTI line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM1) |
| |
| /** |
| * @brief Check whether the specified PVM1 EXTI interrupt flag is set or not. |
| * @retval EXTI PVM1 Line Status. |
| */ |
| #define __HAL_PWR_PVM1_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM1) |
| |
| /** |
| * @brief Clear the PVM1 EXTI flag. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM1_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM1) |
| |
| #endif /* PWR_CR2_PVME1 */ |
| |
| |
| #if defined(PWR_CR2_PVME2) |
| /** |
| * @brief Enable the PVM2 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM2) |
| |
| /** |
| * @brief Disable the PVM2 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM2) |
| |
| /** |
| * @brief Enable the PVM2 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM2) |
| |
| /** |
| * @brief Disable the PVM2 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM2) |
| |
| /** |
| * @brief Enable the PVM2 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM2) |
| |
| /** |
| * @brief Disable the PVM2 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM2) |
| |
| /** |
| * @brief Enable the PVM2 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM2) |
| |
| |
| /** |
| * @brief Disable the PVM2 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM2) |
| |
| |
| /** |
| * @brief PVM2 EXTI line configuration: set rising & falling edge trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_ENABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM2_EXTI_ENABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM2_EXTI_ENABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Disable the PVM2 Extended Interrupt Rising & Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_DISABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM2_EXTI_DISABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM2_EXTI_DISABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Generate a Software interrupt on selected EXTI line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM2) |
| |
| /** |
| * @brief Check whether the specified PVM2 EXTI interrupt flag is set or not. |
| * @retval EXTI PVM2 Line Status. |
| */ |
| #define __HAL_PWR_PVM2_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM2) |
| |
| /** |
| * @brief Clear the PVM2 EXTI flag. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM2_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM2) |
| |
| #endif /* PWR_CR2_PVME2 */ |
| |
| |
| /** |
| * @brief Enable the PVM3 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM3) |
| |
| /** |
| * @brief Disable the PVM3 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM3) |
| |
| /** |
| * @brief Enable the PVM3 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM3) |
| |
| /** |
| * @brief Disable the PVM3 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM3) |
| |
| /** |
| * @brief Enable the PVM3 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM3) |
| |
| /** |
| * @brief Disable the PVM3 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM3) |
| |
| /** |
| * @brief Enable the PVM3 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM3) |
| |
| |
| /** |
| * @brief Disable the PVM3 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM3) |
| |
| |
| /** |
| * @brief PVM3 EXTI line configuration: set rising & falling edge trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_ENABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM3_EXTI_ENABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM3_EXTI_ENABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Disable the PVM3 Extended Interrupt Rising & Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_DISABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM3_EXTI_DISABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM3_EXTI_DISABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Generate a Software interrupt on selected EXTI line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM3) |
| |
| /** |
| * @brief Check whether the specified PVM3 EXTI interrupt flag is set or not. |
| * @retval EXTI PVM3 Line Status. |
| */ |
| #define __HAL_PWR_PVM3_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM3) |
| |
| /** |
| * @brief Clear the PVM3 EXTI flag. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM3_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM3) |
| |
| |
| |
| |
| /** |
| * @brief Enable the PVM4 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM4) |
| |
| /** |
| * @brief Disable the PVM4 Extended Interrupt Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR2, PWR_EXTI_LINE_PVM4) |
| |
| /** |
| * @brief Enable the PVM4 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM4) |
| |
| /** |
| * @brief Disable the PVM4 Event Line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR2, PWR_EVENT_LINE_PVM4) |
| |
| /** |
| * @brief Enable the PVM4 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM4) |
| |
| /** |
| * @brief Disable the PVM4 Extended Interrupt Rising Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR2, PWR_EXTI_LINE_PVM4) |
| |
| /** |
| * @brief Enable the PVM4 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM4) |
| |
| |
| /** |
| * @brief Disable the PVM4 Extended Interrupt Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR2, PWR_EXTI_LINE_PVM4) |
| |
| |
| /** |
| * @brief PVM4 EXTI line configuration: set rising & falling edge trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_ENABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM4_EXTI_ENABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM4_EXTI_ENABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Disable the PVM4 Extended Interrupt Rising & Falling Trigger. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_DISABLE_RISING_FALLING_EDGE() \ |
| do { \ |
| __HAL_PWR_PVM4_EXTI_DISABLE_RISING_EDGE(); \ |
| __HAL_PWR_PVM4_EXTI_DISABLE_FALLING_EDGE(); \ |
| } while(0) |
| |
| /** |
| * @brief Generate a Software interrupt on selected EXTI line. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER2, PWR_EXTI_LINE_PVM4) |
| |
| /** |
| * @brief Check whether or not the specified PVM4 EXTI interrupt flag is set. |
| * @retval EXTI PVM4 Line Status. |
| */ |
| #define __HAL_PWR_PVM4_EXTI_GET_FLAG() (EXTI->PR2 & PWR_EXTI_LINE_PVM4) |
| |
| /** |
| * @brief Clear the PVM4 EXTI flag. |
| * @retval None |
| */ |
| #define __HAL_PWR_PVM4_EXTI_CLEAR_FLAG() WRITE_REG(EXTI->PR2, PWR_EXTI_LINE_PVM4) |
| |
| |
| /** |
| * @brief Configure the main internal regulator output voltage. |
| * @param __REGULATOR__: specifies the regulator output voltage to achieve |
| * a tradeoff between performance and power consumption. |
| * This parameter can be one of the following values: |
| * @arg @ref PWR_REGULATOR_VOLTAGE_SCALE1_BOOST Regulator voltage output range 1 mode, |
| * typical output voltage at 1.28 V, |
| * system frequency up to 170 MHz. |
| * @arg @ref PWR_REGULATOR_VOLTAGE_SCALE1 Regulator voltage output range 1 mode, |
| * typical output voltage at 1.2 V, |
| * system frequency up to 150 MHz. |
| * @arg @ref PWR_REGULATOR_VOLTAGE_SCALE2 Regulator voltage output range 2 mode, |
| * typical output voltage at 1.0 V, |
| * system frequency up to 26 MHz. |
| * @note This macro is similar to HAL_PWREx_ControlVoltageScaling() API but doesn't check |
| * whether or not VOSF flag is cleared when moving from range 2 to range 1. User |
| * may resort to __HAL_PWR_GET_FLAG() macro to check VOSF bit resetting. |
| * @retval None |
| */ |
| #define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \ |
| __IO uint32_t tmpreg; \ |
| MODIFY_REG(PWR->CR1, PWR_CR1_VOS, (__REGULATOR__)); \ |
| /* Delay after an RCC peripheral clock enabling */ \ |
| tmpreg = READ_BIT(PWR->CR1, PWR_CR1_VOS); \ |
| UNUSED(tmpreg); \ |
| } while(0) |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macros --------------------------------------------------------*/ |
| /** @addtogroup PWREx_Private_Macros PWR Extended Private Macros |
| * @{ |
| */ |
| |
| #define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \ |
| ((PIN) == PWR_WAKEUP_PIN2) || \ |
| ((PIN) == PWR_WAKEUP_PIN3) || \ |
| ((PIN) == PWR_WAKEUP_PIN4) || \ |
| ((PIN) == PWR_WAKEUP_PIN5) || \ |
| ((PIN) == PWR_WAKEUP_PIN1_HIGH) || \ |
| ((PIN) == PWR_WAKEUP_PIN2_HIGH) || \ |
| ((PIN) == PWR_WAKEUP_PIN3_HIGH) || \ |
| ((PIN) == PWR_WAKEUP_PIN4_HIGH) || \ |
| ((PIN) == PWR_WAKEUP_PIN5_HIGH) || \ |
| ((PIN) == PWR_WAKEUP_PIN1_LOW) || \ |
| ((PIN) == PWR_WAKEUP_PIN2_LOW) || \ |
| ((PIN) == PWR_WAKEUP_PIN3_LOW) || \ |
| ((PIN) == PWR_WAKEUP_PIN4_LOW) || \ |
| ((PIN) == PWR_WAKEUP_PIN5_LOW)) |
| |
| #define IS_PWR_PVM_TYPE(TYPE) (((TYPE) == PWR_PVM_1) ||\ |
| ((TYPE) == PWR_PVM_2) ||\ |
| ((TYPE) == PWR_PVM_3) ||\ |
| ((TYPE) == PWR_PVM_4)) |
| |
| #define IS_PWR_PVM_MODE(MODE) (((MODE) == PWR_PVM_MODE_NORMAL) ||\ |
| ((MODE) == PWR_PVM_MODE_IT_RISING) ||\ |
| ((MODE) == PWR_PVM_MODE_IT_FALLING) ||\ |
| ((MODE) == PWR_PVM_MODE_IT_RISING_FALLING) ||\ |
| ((MODE) == PWR_PVM_MODE_EVENT_RISING) ||\ |
| ((MODE) == PWR_PVM_MODE_EVENT_FALLING) ||\ |
| ((MODE) == PWR_PVM_MODE_EVENT_RISING_FALLING)) |
| |
| #if defined(PWR_CR5_R1MODE) |
| #define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1_BOOST) || \ |
| ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \ |
| ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2)) |
| #else |
| #define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \ |
| ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2)) |
| #endif |
| |
| |
| #define IS_PWR_BATTERY_RESISTOR_SELECT(RESISTOR) (((RESISTOR) == PWR_BATTERY_CHARGING_RESISTOR_5) ||\ |
| ((RESISTOR) == PWR_BATTERY_CHARGING_RESISTOR_1_5)) |
| |
| #define IS_PWR_BATTERY_CHARGING(CHARGING) (((CHARGING) == PWR_BATTERY_CHARGING_DISABLE) ||\ |
| ((CHARGING) == PWR_BATTERY_CHARGING_ENABLE)) |
| |
| #define IS_PWR_GPIO_BIT_NUMBER(BIT_NUMBER) (((BIT_NUMBER) & GPIO_PIN_MASK) != (uint32_t)0x00U) |
| #define IS_PWR_GPIO(GPIO) (((GPIO) == PWR_GPIO_A) ||\ |
| ((GPIO) == PWR_GPIO_B) ||\ |
| ((GPIO) == PWR_GPIO_C) ||\ |
| ((GPIO) == PWR_GPIO_D) ||\ |
| ((GPIO) == PWR_GPIO_E) ||\ |
| ((GPIO) == PWR_GPIO_F) ||\ |
| ((GPIO) == PWR_GPIO_G)) |
| |
| |
| /** |
| * @} |
| */ |
| |
| |
| /** @addtogroup PWREx_Exported_Functions PWR Extended Exported Functions |
| * @{ |
| */ |
| |
| /** @addtogroup PWREx_Exported_Functions_Group1 Extended Peripheral Control functions |
| * @{ |
| */ |
| |
| |
| /* Peripheral Control functions **********************************************/ |
| uint32_t HAL_PWREx_GetVoltageRange(void); |
| HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling); |
| void HAL_PWREx_EnableBatteryCharging(uint32_t ResistorSelection); |
| void HAL_PWREx_DisableBatteryCharging(void); |
| void HAL_PWREx_EnableInternalWakeUpLine(void); |
| void HAL_PWREx_DisableInternalWakeUpLine(void); |
| HAL_StatusTypeDef HAL_PWREx_EnableGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber); |
| HAL_StatusTypeDef HAL_PWREx_DisableGPIOPullUp(uint32_t GPIO, uint32_t GPIONumber); |
| HAL_StatusTypeDef HAL_PWREx_EnableGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber); |
| HAL_StatusTypeDef HAL_PWREx_DisableGPIOPullDown(uint32_t GPIO, uint32_t GPIONumber); |
| void HAL_PWREx_EnablePullUpPullDownConfig(void); |
| void HAL_PWREx_DisablePullUpPullDownConfig(void); |
| void HAL_PWREx_EnableSRAM2ContentRetention(void); |
| void HAL_PWREx_DisableSRAM2ContentRetention(void); |
| #if defined(PWR_CR2_PVME1) |
| void HAL_PWREx_EnablePVM1(void); |
| void HAL_PWREx_DisablePVM1(void); |
| #endif /* PWR_CR2_PVME1 */ |
| #if defined(PWR_CR2_PVME2) |
| void HAL_PWREx_EnablePVM2(void); |
| void HAL_PWREx_DisablePVM2(void); |
| #endif /* PWR_CR2_PVME2 */ |
| void HAL_PWREx_EnablePVM3(void); |
| void HAL_PWREx_DisablePVM3(void); |
| void HAL_PWREx_EnablePVM4(void); |
| void HAL_PWREx_DisablePVM4(void); |
| HAL_StatusTypeDef HAL_PWREx_ConfigPVM(PWR_PVMTypeDef *sConfigPVM); |
| |
| #if defined(PWR_CR3_UCPD_DBDIS) |
| void HAL_PWREx_EnableUSBDeadBatteryPD(void); |
| void HAL_PWREx_DisableUSBDeadBatteryPD(void); |
| #endif /* PWR_CR3_UCPD_DBDIS */ |
| #if defined(PWR_CR3_UCPD_STDBY) |
| void HAL_PWREx_EnableUSBStandByModePD(void); |
| void HAL_PWREx_DisableUSBStandByModePD (void); |
| #endif /* PWR_CR3_UCPD_STDBY */ |
| |
| /* Low Power modes configuration functions ************************************/ |
| void HAL_PWREx_EnableLowPowerRunMode(void); |
| HAL_StatusTypeDef HAL_PWREx_DisableLowPowerRunMode(void); |
| void HAL_PWREx_EnterSTOP0Mode(uint8_t STOPEntry); |
| void HAL_PWREx_EnterSTOP1Mode(uint8_t STOPEntry); |
| void HAL_PWREx_EnterSHUTDOWNMode(void); |
| |
| void HAL_PWREx_PVD_PVM_IRQHandler(void); |
| #if defined(PWR_CR2_PVME1) |
| void HAL_PWREx_PVM1Callback(void); |
| #endif /* PWR_CR2_PVME1 */ |
| #if defined(PWR_CR2_PVME2) |
| void HAL_PWREx_PVM2Callback(void); |
| #endif /* PWR_CR2_PVME2 */ |
| void HAL_PWREx_PVM3Callback(void); |
| void HAL_PWREx_PVM4Callback(void); |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| |
| #endif /* STM32G4xx_HAL_PWR_EX_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
