/**
  ******************************************************************************
  * @file    stm32h7xx_hal_timebase_rtc_alarm_template.c
  * @author  MCD Application Team
  * @brief   HAL time base based on the hardware RTC_ALARM Template.
  *
  *          This file override the native HAL time base functions (defined as weak)
  *          to use the RTC ALARM for time base generation:
  *           + Initializes the RTC peripheral to increment the seconds registers each 1ms
  *           + The alarm is configured to assert an interrupt when the RTC reaches 1ms
  *           + HAL_IncTick is called at each Alarm event and the time is reset to 00:00:00
  *           + HSE (default), LSE or LSI can be selected as RTC clock source
 @verbatim
  ==============================================================================
                        ##### How to use this driver #####
  ==============================================================================
    [..]
    This file must be copied to the application folder and modified as follows:
    (#) Rename it to 'stm32h7xx_hal_timebase_rtc_alarm.c'
    (#) Add this file and the RTC HAL drivers to your project and uncomment
       HAL_RTC_MODULE_ENABLED define in stm32h7xx_hal_conf.h

    [..]
    (@) HAL RTC alarm and HAL RTC wakeup drivers can not be used with low power modes:
        The wake up capability of the RTC may be intrusive in case of prior low power mode
        configuration requiring different wake up sources.
        Application/Example behavior is no more guaranteed
    (@) The stm32h7xx_hal_timebase_tim use is recommended for the Applications/Examples
          requiring low power modes

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32h7xx_hal.h"
/** @addtogroup STM32H7xx_HAL_Driver
  * @{
  */

/** @defgroup HAL_TimeBase_RTC_Alarm_Template  HAL TimeBase RTC Alarm Template
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/

/* Uncomment the line below to select the appropriate RTC Clock source for your application:
  + RTC_CLOCK_SOURCE_HSE: can be selected for applications requiring timing precision.
  + RTC_CLOCK_SOURCE_LSE: can be selected for applications with low constraint on timing
                          precision.
  + RTC_CLOCK_SOURCE_LSI: can be selected for applications with low constraint on timing
                          precision.
  */
#define RTC_CLOCK_SOURCE_HSE
/* #define RTC_CLOCK_SOURCE_LSE */
/* #define RTC_CLOCK_SOURCE_LSI */

#ifdef RTC_CLOCK_SOURCE_HSE
  #define RTC_ASYNCH_PREDIV       99U
  #define RTC_SYNCH_PREDIV        9U
  #define RCC_RTCCLKSOURCE_1MHZ   ((uint32_t)((uint32_t)RCC_BDCR_RTCSEL | (uint32_t)((HSE_VALUE/1000000U) << 12U)))
#else /* RTC_CLOCK_SOURCE_LSE || RTC_CLOCK_SOURCE_LSI */
  #define RTC_ASYNCH_PREDIV       0U
  #define RTC_SYNCH_PREDIV        31U
#endif /* RTC_CLOCK_SOURCE_HSE */

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
static RTC_HandleTypeDef        hRTC_Handle;
/* Private function prototypes -----------------------------------------------*/
void RTC_Alarm_IRQHandler(void);
/* Private functions ---------------------------------------------------------*/

/**
  * @brief  This function configures the RTC_ALARMA as a time base source.
  *         The time source is configured to have 1ms time base with a dedicated
  *         Tick interrupt priority.
  * @note   This function is called  automatically at the beginning of program after
  *         reset by HAL_Init() or at any time when clock is configured, by HAL_RCC_ClockConfig().
  * @param  TickPriority Tick interrupt priority.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_InitTick (uint32_t TickPriority)
{
  __IO uint32_t counter = 0U;

  RCC_OscInitTypeDef        RCC_OscInitStruct;
  RCC_PeriphCLKInitTypeDef  PeriphClkInitStruct;

#ifdef RTC_CLOCK_SOURCE_LSE
  /* Configure LSE as RTC clock source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSE;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  RCC_OscInitStruct.LSEState = RCC_LSE_ON;
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSE;
#elif defined (RTC_CLOCK_SOURCE_LSI)
  /* Configure LSI as RTC clock source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSI;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  RCC_OscInitStruct.LSIState = RCC_LSI_ON;
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;
#elif defined (RTC_CLOCK_SOURCE_HSE)
  /* Configure HSE as RTC clock source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  /* Ensure that RTC is clocked by 1MHz */
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_1MHZ;
#else
#error Please select the RTC Clock source
#endif /* RTC_CLOCK_SOURCE_LSE */

  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) == HAL_OK)
  {
    PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC;
    if(HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) == HAL_OK)
    {
      /* Enable RTC Clock */
      __HAL_RCC_RTC_ENABLE();
      /* The time base should be 1ms
         Time base = ((RTC_ASYNCH_PREDIV + 1) * (RTC_SYNCH_PREDIV + 1)) / RTC_CLOCK
         HSE as RTC clock
           Time base = ((99 + 1) * (9 + 1)) / 1MHz
                     = 1ms
         LSE as RTC clock
           Time base = ((31 + 1) * (0 + 1)) / 32.768KHz
                     = ~1ms
         LSI as RTC clock
           Time base = ((31 + 1) * (0 + 1)) / 32KHz
                     = 1ms
      */
      hRTC_Handle.Instance = RTC;
      hRTC_Handle.Init.HourFormat = RTC_HOURFORMAT_24;
      hRTC_Handle.Init.AsynchPrediv = RTC_ASYNCH_PREDIV;
      hRTC_Handle.Init.SynchPrediv = RTC_SYNCH_PREDIV;
      hRTC_Handle.Init.OutPut = RTC_OUTPUT_DISABLE;
      hRTC_Handle.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;
      hRTC_Handle.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;

      if(HAL_RTC_Init(&hRTC_Handle) != HAL_OK)
      {
        return HAL_ERROR;
      }

      /* Disable the write protection for RTC registers */
      __HAL_RTC_WRITEPROTECTION_DISABLE(&hRTC_Handle);

      /* Disable the Alarm A interrupt */
      __HAL_RTC_ALARMA_DISABLE(&hRTC_Handle);

      /* Clear flag alarm A */
      __HAL_RTC_ALARM_CLEAR_FLAG(&hRTC_Handle, RTC_FLAG_ALRAF);

      counter = 0U;
      /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
#if defined(RTC_ICSR_ALRAWF)
      while( READ_BIT(hRTC_Handle.Instance->ICSR, RTC_FLAG_ALRAWF) == 0U)
#else
      while(__HAL_RTC_ALARM_GET_FLAG(&hRTC_Handle, RTC_FLAG_ALRAWF) == (uint32_t)RESET)
#endif /* RTC_ICSR_ALRAWF */
      {
        if(counter++ == (SystemCoreClock /48U)) /* Timeout = ~ 1s */
        {
          return HAL_ERROR;
        }
      }

      hRTC_Handle.Instance->ALRMAR = (uint32_t)0x01U;

      /* Configure the Alarm state: Enable Alarm */
      __HAL_RTC_ALARMA_ENABLE(&hRTC_Handle);
      /* Configure the Alarm interrupt */
      __HAL_RTC_ALARM_ENABLE_IT(&hRTC_Handle, RTC_IT_ALRA);

      /* RTC Alarm Interrupt Configuration: EXTI configuration */
      __HAL_RTC_ALARM_EXTI_ENABLE_IT();
      __HAL_RTC_ALARM_EXTI_ENABLE_RISING_EDGE();

      /* Check if the Initialization mode is set */
#if defined(RTC_ISR_INITF)
      if((hRTC_Handle.Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET)
#else
      if((hRTC_Handle.Instance->ICSR & RTC_ICSR_INITF) == (uint32_t)RESET)
#endif /* RTC_ISR_INITF */
      {
        /* Set the Initialization mode */
#if defined(RTC_ISR_INITF)
        hRTC_Handle.Instance->ISR = (uint32_t)RTC_INIT_MASK;
#else
        hRTC_Handle.Instance->ICSR = (uint32_t)RTC_INIT_MASK;
#endif /* RTC_ISR_INITF */
        counter = 0U;
#if defined(RTC_ISR_INITF)
        while((hRTC_Handle.Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET)
#else
        while((hRTC_Handle.Instance->ICSR & RTC_ICSR_INITF) == (uint32_t)RESET)
#endif /* RTC_ISR_INITF */
        {
          if(counter++ == (SystemCoreClock /48U)) /* Timeout = ~ 1s */
          {
            return HAL_ERROR;
          }
        }
      }
      hRTC_Handle.Instance->DR = 0U;
      hRTC_Handle.Instance->TR = 0U;

#if defined(RTC_ISR_INIT)
      hRTC_Handle.Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
#else
      hRTC_Handle.Instance->ICSR &= (uint32_t)~RTC_ICSR_INIT;
#endif /* RTC_ISR_INIT */

      /* Enable the write protection for RTC registers */
      __HAL_RTC_WRITEPROTECTION_ENABLE(&hRTC_Handle);

      if (TickPriority < (1UL << __NVIC_PRIO_BITS))
      {
      HAL_NVIC_SetPriority(RTC_Alarm_IRQn, TickPriority, 0U);
      HAL_NVIC_EnableIRQ(RTC_Alarm_IRQn);

        uwTickPrio = TickPriority;
      return HAL_OK;
      }
      else
      {
        return HAL_ERROR;
      }
    }
  }
  return HAL_ERROR;
}

/**
  * @brief  Suspend Tick increment.
  * @note   Disable the tick increment by disabling RTC ALARM interrupt.
  * @retval None
  */
void HAL_SuspendTick(void)
{
  /* Disable the write protection for RTC registers */
  __HAL_RTC_WRITEPROTECTION_DISABLE(&hRTC_Handle);
  /* Disable RTC ALARM update Interrupt */
  __HAL_RTC_ALARM_DISABLE_IT(&hRTC_Handle, RTC_IT_ALRA);
  /* Enable the write protection for RTC registers */
  __HAL_RTC_WRITEPROTECTION_ENABLE(&hRTC_Handle);
}

/**
  * @brief  Resume Tick increment.
  * @note   Enable the tick increment by Enabling RTC ALARM interrupt.
  * @retval None
  */
void HAL_ResumeTick(void)
{
  /* Disable the write protection for RTC registers */
  __HAL_RTC_WRITEPROTECTION_DISABLE(&hRTC_Handle);
  /* Enable RTC ALARM Update interrupt */
  __HAL_RTC_ALARM_ENABLE_IT(&hRTC_Handle, RTC_IT_ALRA);
  /* Enable the write protection for RTC registers */
  __HAL_RTC_WRITEPROTECTION_ENABLE(&hRTC_Handle);
}

/**
  * @brief  ALARM A Event Callback in non blocking mode
  * @note   This function is called  when RTC_ALARM interrupt took place, inside
  * RTC_ALARM_IRQHandler(). It makes a direct call to HAL_IncTick() to increment
  * a global variable "uwTick" used as application time base.
  * @param  hrtc RTC handle
  * @retval None
  */
void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc)
{
  __IO uint32_t counter = 0U;

  HAL_IncTick();

  __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);

  /* Set the Initialization mode */
#if defined(RTC_ISR_INIT)
  hrtc->Instance->ISR = (uint32_t)RTC_INIT_MASK;

  while((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET)
#else
  hrtc->Instance->ICSR = (uint32_t)RTC_INIT_MASK;

  while((hrtc->Instance->ICSR & RTC_ICSR_INITF) == (uint32_t)RESET)
#endif /* RTC_ISR_INIT */
  {
    if(counter++ == (SystemCoreClock /48U)) /* Timeout = ~ 1s */
    {
      break;
    }
  }

  hrtc->Instance->DR = 0U;
  hrtc->Instance->TR = 0U;
#if defined(RTC_ISR_INIT)
  hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
#else
  hrtc->Instance->ICSR &= (uint32_t)~RTC_ICSR_INIT;
#endif /* RTC_ISR_INIT  */
  /* Enable the write protection for RTC registers */
  __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
}

/**
  * @brief  This function handles RTC ALARM interrupt request.
  * @retval None
  */
void RTC_Alarm_IRQHandler(void)
{
  HAL_RTC_AlarmIRQHandler(&hRTC_Handle);
}

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/