| /** |
| ****************************************************************************** |
| * @file stm32h7xx_hal_ospi.h |
| * @author MCD Application Team |
| * @brief Header file of OSPI HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved. |
| * |
| * This software is licensed under terms that can be found in the LICENSE file |
| * in the root directory of this software component. |
| * If no LICENSE file comes with this software, it is provided AS-IS. |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32H7xx_HAL_OSPI_H |
| #define STM32H7xx_HAL_OSPI_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32h7xx_hal_def.h" |
| |
| #if defined(OCTOSPI) || defined(OCTOSPI1) || defined(OCTOSPI2) |
| |
| /** @addtogroup STM32H7xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup OSPI |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup OSPI_Exported_Types OSPI Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief OSPI Init structure definition |
| */ |
| typedef struct |
| { |
| uint32_t FifoThreshold; /*!< This is the threshold used by the Peripheral to generate the interrupt |
| indicating that data are available in reception or free place |
| is available in transmission. |
| This parameter can be a value between 1 and 32 */ |
| uint32_t DualQuad; /*!< It enables or not the dual-quad mode which allow to access up to |
| quad mode on two different devices to increase the throughput. |
| This parameter can be a value of @ref OSPI_DualQuad */ |
| uint32_t MemoryType; /*!< It indicates the external device type connected to the OSPI. |
| This parameter can be a value of @ref OSPI_MemoryType */ |
| uint32_t DeviceSize; /*!< It defines the size of the external device connected to the OSPI, |
| it corresponds to the number of address bits required to access |
| the external device. |
| This parameter can be a value between 1 and 32 */ |
| uint32_t ChipSelectHighTime; /*!< It defines the minimum number of clocks which the chip select |
| must remain high between commands. |
| This parameter can be a value between 1 and 8 */ |
| uint32_t FreeRunningClock; /*!< It enables or not the free running clock. |
| This parameter can be a value of @ref OSPI_FreeRunningClock */ |
| uint32_t ClockMode; /*!< It indicates the level of clock when the chip select is released. |
| This parameter can be a value of @ref OSPI_ClockMode */ |
| uint32_t WrapSize; /*!< It indicates the wrap-size corresponding the external device configuration. |
| This parameter can be a value of @ref OSPI_WrapSize */ |
| uint32_t ClockPrescaler; /*!< It specifies the prescaler factor used for generating |
| the external clock based on the AHB clock. |
| This parameter can be a value between 1 and 256 */ |
| uint32_t SampleShifting; /*!< It allows to delay to 1/2 cycle the data sampling in order |
| to take in account external signal delays. |
| This parameter can be a value of @ref OSPI_SampleShifting */ |
| uint32_t DelayHoldQuarterCycle; /*!< It allows to hold to 1/4 cycle the data. |
| This parameter can be a value of @ref OSPI_DelayHoldQuarterCycle */ |
| uint32_t ChipSelectBoundary; /*!< It enables the transaction boundary feature and |
| defines the boundary of bytes to release the chip select. |
| This parameter can be a value between 0 and 31 */ |
| uint32_t DelayBlockBypass; /*!< It enables the delay block bypass, so the sampling is not affected |
| by the delay block. |
| This parameter can be a value of @ref OSPI_DelayBlockBypass */ |
| uint32_t MaxTran; /*!< It enables the communication regulation feature. The chip select is |
| released every MaxTran+1 bytes when the other OctoSPI request the access |
| to the bus. |
| This parameter can be a value between 0 and 255 */ |
| uint32_t Refresh; /*!< It enables the refresh rate feature. The chip select is released every |
| Refresh+1 clock cycles. |
| This parameter can be a value between 0 and 0xFFFFFFFF */ |
| }OSPI_InitTypeDef; |
| |
| /** |
| * @brief HAL OSPI Handle Structure definition |
| */ |
| #if defined (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) |
| typedef struct __OSPI_HandleTypeDef |
| #else |
| typedef struct |
| #endif /* (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) */ |
| { |
| OCTOSPI_TypeDef *Instance; /*!< OSPI registers base address */ |
| OSPI_InitTypeDef Init; /*!< OSPI initialization parameters */ |
| uint8_t *pBuffPtr; /*!< Address of the OSPI buffer for transfer */ |
| __IO uint32_t XferSize; /*!< Number of data to transfer */ |
| __IO uint32_t XferCount; /*!< Counter of data transferred */ |
| MDMA_HandleTypeDef *hmdma; /*!< Handle of the MDMA channel used for the transfer */ |
| __IO uint32_t State; /*!< Internal state of the OSPI HAL driver */ |
| __IO uint32_t ErrorCode; /*!< Error code in case of HAL driver internal error */ |
| uint32_t Timeout; /*!< Timeout used for the OSPI external device access */ |
| #if defined (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) |
| void (* ErrorCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* AbortCpltCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* FifoThresholdCallback)(struct __OSPI_HandleTypeDef *hospi); |
| void (* CmdCpltCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* RxCpltCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* TxCpltCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* RxHalfCpltCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* TxHalfCpltCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* StatusMatchCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* TimeOutCallback) (struct __OSPI_HandleTypeDef *hospi); |
| |
| void (* MspInitCallback) (struct __OSPI_HandleTypeDef *hospi); |
| void (* MspDeInitCallback) (struct __OSPI_HandleTypeDef *hospi); |
| #endif /* (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) */ |
| }OSPI_HandleTypeDef; |
| |
| /** |
| * @brief HAL OSPI Regular Command Structure definition |
| */ |
| typedef struct |
| { |
| uint32_t OperationType; /*!< It indicates if the configuration applies to the common registers or |
| to the registers for the write operation (these registers are only |
| used for memory-mapped mode). |
| This parameter can be a value of @ref OSPI_OperationType */ |
| uint32_t FlashId; /*!< It indicates which external device is selected for this command (it |
| applies only if Dualquad is disabled in the initialization structure). |
| This parameter can be a value of @ref OSPI_FlashID */ |
| uint32_t Instruction; /*!< It contains the instruction to be sent to the device. |
| This parameter can be a value between 0 and 0xFFFFFFFF */ |
| uint32_t InstructionMode; /*!< It indicates the mode of the instruction. |
| This parameter can be a value of @ref OSPI_InstructionMode */ |
| uint32_t InstructionSize; /*!< It indicates the size of the instruction. |
| This parameter can be a value of @ref OSPI_InstructionSize */ |
| uint32_t InstructionDtrMode; /*!< It enables or not the DTR mode for the instruction phase. |
| This parameter can be a value of @ref OSPI_InstructionDtrMode */ |
| uint32_t Address; /*!< It contains the address to be sent to the device. |
| This parameter can be a value between 0 and 0xFFFFFFFF */ |
| uint32_t AddressMode; /*!< It indicates the mode of the address. |
| This parameter can be a value of @ref OSPI_AddressMode */ |
| uint32_t AddressSize; /*!< It indicates the size of the address. |
| This parameter can be a value of @ref OSPI_AddressSize */ |
| uint32_t AddressDtrMode; /*!< It enables or not the DTR mode for the address phase. |
| This parameter can be a value of @ref OSPI_AddressDtrMode */ |
| uint32_t AlternateBytes; /*!< It contains the alternate bytes to be sent to the device. |
| This parameter can be a value between 0 and 0xFFFFFFFF */ |
| uint32_t AlternateBytesMode; /*!< It indicates the mode of the alternate bytes. |
| This parameter can be a value of @ref OSPI_AlternateBytesMode */ |
| uint32_t AlternateBytesSize; /*!< It indicates the size of the alternate bytes. |
| This parameter can be a value of @ref OSPI_AlternateBytesSize */ |
| uint32_t AlternateBytesDtrMode; /*!< It enables or not the DTR mode for the alternate bytes phase. |
| This parameter can be a value of @ref OSPI_AlternateBytesDtrMode */ |
| uint32_t DataMode; /*!< It indicates the mode of the data. |
| This parameter can be a value of @ref OSPI_DataMode */ |
| uint32_t NbData; /*!< It indicates the number of data transferred with this command. |
| This field is only used for indirect mode. |
| This parameter can be a value between 1 and 0xFFFFFFFF */ |
| uint32_t DataDtrMode; /*!< It enables or not the DTR mode for the data phase. |
| This parameter can be a value of @ref OSPI_DataDtrMode */ |
| uint32_t DummyCycles; /*!< It indicates the number of dummy cycles inserted before data phase. |
| This parameter can be a value between 0 and 31 */ |
| uint32_t DQSMode; /*!< It enables or not the data strobe management. |
| This parameter can be a value of @ref OSPI_DQSMode */ |
| uint32_t SIOOMode; /*!< It enables or not the SIOO mode. |
| This parameter can be a value of @ref OSPI_SIOOMode */ |
| }OSPI_RegularCmdTypeDef; |
| |
| /** |
| * @brief HAL OSPI Hyperbus Configuration Structure definition |
| */ |
| typedef struct |
| { |
| uint32_t RWRecoveryTime; /*!< It indicates the number of cycles for the device read write recovery time. |
| This parameter can be a value between 0 and 255 */ |
| uint32_t AccessTime; /*!< It indicates the number of cycles for the device access time. |
| This parameter can be a value between 0 and 255 */ |
| uint32_t WriteZeroLatency; /*!< It enables or not the latency for the write access. |
| This parameter can be a value of @ref OSPI_WriteZeroLatency */ |
| uint32_t LatencyMode; /*!< It configures the latency mode. |
| This parameter can be a value of @ref OSPI_LatencyMode */ |
| }OSPI_HyperbusCfgTypeDef; |
| |
| /** |
| * @brief HAL OSPI Hyperbus Command Structure definition |
| */ |
| typedef struct |
| { |
| uint32_t AddressSpace; /*!< It indicates the address space accessed by the command. |
| This parameter can be a value of @ref OSPI_AddressSpace */ |
| uint32_t Address; /*!< It contains the address to be sent tot he device. |
| This parameter can be a value between 0 and 0xFFFFFFFF */ |
| uint32_t AddressSize; /*!< It indicates the size of the address. |
| This parameter can be a value of @ref OSPI_AddressSize */ |
| uint32_t NbData; /*!< It indicates the number of data transferred with this command. |
| This field is only used for indirect mode. |
| This parameter can be a value between 1 and 0xFFFFFFFF |
| In case of autopolling mode, this parameter can be any value between 1 and 4 */ |
| uint32_t DQSMode; /*!< It enables or not the data strobe management. |
| This parameter can be a value of @ref OSPI_DQSMode */ |
| }OSPI_HyperbusCmdTypeDef; |
| |
| /** |
| * @brief HAL OSPI Auto Polling mode configuration structure definition |
| */ |
| typedef struct |
| { |
| uint32_t Match; /*!< Specifies the value to be compared with the masked status register to get a match. |
| This parameter can be any value between 0 and 0xFFFFFFFF */ |
| uint32_t Mask; /*!< Specifies the mask to be applied to the status bytes received. |
| This parameter can be any value between 0 and 0xFFFFFFFF */ |
| uint32_t MatchMode; /*!< Specifies the method used for determining a match. |
| This parameter can be a value of @ref OSPI_MatchMode */ |
| uint32_t AutomaticStop; /*!< Specifies if automatic polling is stopped after a match. |
| This parameter can be a value of @ref OSPI_AutomaticStop */ |
| uint32_t Interval; /*!< Specifies the number of clock cycles between two read during automatic polling phases. |
| This parameter can be any value between 0 and 0xFFFF */ |
| }OSPI_AutoPollingTypeDef; |
| |
| /** |
| * @brief HAL OSPI Memory Mapped mode configuration structure definition |
| */ |
| typedef struct |
| { |
| uint32_t TimeOutActivation; /*!< Specifies if the timeout counter is enabled to release the chip select. |
| This parameter can be a value of @ref OSPI_TimeOutActivation */ |
| uint32_t TimeOutPeriod; /*!< Specifies the number of clock to wait when the FIFO is full before to release the chip select. |
| This parameter can be any value between 0 and 0xFFFF */ |
| }OSPI_MemoryMappedTypeDef; |
| |
| /** |
| * @brief HAL OSPI IO Manager Configuration structure definition |
| */ |
| typedef struct |
| { |
| uint32_t ClkPort; /*!< It indicates which port of the OSPI IO Manager is used for the CLK pins. |
| This parameter can be a value between 1 and 8 */ |
| uint32_t DQSPort; /*!< It indicates which port of the OSPI IO Manager is used for the DQS pin. |
| This parameter can be a value between 0 and 8, 0 means that signal not used */ |
| uint32_t NCSPort; /*!< It indicates which port of the OSPI IO Manager is used for the NCS pin. |
| This parameter can be a value between 1 and 8 */ |
| uint32_t IOLowPort; /*!< It indicates which port of the OSPI IO Manager is used for the IO[3:0] pins. |
| This parameter can be a value of @ref OSPIM_IOPort */ |
| uint32_t IOHighPort; /*!< It indicates which port of the OSPI IO Manager is used for the IO[7:4] pins. |
| This parameter can be a value of @ref OSPIM_IOPort */ |
| uint32_t Req2AckTime; /*!< It indicates the minimum switching duration (in number of clock cycles) expected |
| if some signals are multiplexed in the OSPI IO Manager with the other OSPI. |
| This parameter can be a value between 1 and 256 */ |
| }OSPIM_CfgTypeDef; |
| |
| #if defined (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) |
| /** |
| * @brief HAL OSPI Callback ID enumeration definition |
| */ |
| typedef enum |
| { |
| HAL_OSPI_ERROR_CB_ID = 0x00U, /*!< OSPI Error Callback ID */ |
| HAL_OSPI_ABORT_CB_ID = 0x01U, /*!< OSPI Abort Callback ID */ |
| HAL_OSPI_FIFO_THRESHOLD_CB_ID = 0x02U, /*!< OSPI FIFO Threshold Callback ID */ |
| HAL_OSPI_CMD_CPLT_CB_ID = 0x03U, /*!< OSPI Command Complete Callback ID */ |
| HAL_OSPI_RX_CPLT_CB_ID = 0x04U, /*!< OSPI Rx Complete Callback ID */ |
| HAL_OSPI_TX_CPLT_CB_ID = 0x05U, /*!< OSPI Tx Complete Callback ID */ |
| HAL_OSPI_RX_HALF_CPLT_CB_ID = 0x06U, /*!< OSPI Rx Half Complete Callback ID */ |
| HAL_OSPI_TX_HALF_CPLT_CB_ID = 0x07U, /*!< OSPI Tx Half Complete Callback ID */ |
| HAL_OSPI_STATUS_MATCH_CB_ID = 0x08U, /*!< OSPI Status Match Callback ID */ |
| HAL_OSPI_TIMEOUT_CB_ID = 0x09U, /*!< OSPI Timeout Callback ID */ |
| |
| HAL_OSPI_MSP_INIT_CB_ID = 0x0AU, /*!< OSPI MspInit Callback ID */ |
| HAL_OSPI_MSP_DEINIT_CB_ID = 0x0BU /*!< OSPI MspDeInit Callback ID */ |
| }HAL_OSPI_CallbackIDTypeDef; |
| |
| /** |
| * @brief HAL OSPI Callback pointer definition |
| */ |
| typedef void (*pOSPI_CallbackTypeDef)(OSPI_HandleTypeDef *hospi); |
| #endif /* (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) */ |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup OSPI_Exported_Constants OSPI Exported Constants |
| * @{ |
| */ |
| |
| /** @defgroup OSPI_State OSPI State |
| * @{ |
| */ |
| #define HAL_OSPI_STATE_RESET ((uint32_t)0x00000000U) /*!< Initial state */ |
| #define HAL_OSPI_STATE_HYPERBUS_INIT ((uint32_t)0x00000001U) /*!< Initialization done in hyperbus mode but timing configuration not done */ |
| #define HAL_OSPI_STATE_READY ((uint32_t)0x00000002U) /*!< Driver ready to be used */ |
| #define HAL_OSPI_STATE_CMD_CFG ((uint32_t)0x00000004U) /*!< Command (regular or hyperbus) configured, ready for an action */ |
| #define HAL_OSPI_STATE_READ_CMD_CFG ((uint32_t)0x00000014U) /*!< Read command configuration done, not the write command configuration */ |
| #define HAL_OSPI_STATE_WRITE_CMD_CFG ((uint32_t)0x00000024U) /*!< Write command configuration done, not the read command configuration */ |
| #define HAL_OSPI_STATE_BUSY_CMD ((uint32_t)0x00000008U) /*!< Command without data on-going */ |
| #define HAL_OSPI_STATE_BUSY_TX ((uint32_t)0x00000018U) /*!< Indirect Tx on-going */ |
| #define HAL_OSPI_STATE_BUSY_RX ((uint32_t)0x00000028U) /*!< Indirect Rx on-going */ |
| #define HAL_OSPI_STATE_BUSY_AUTO_POLLING ((uint32_t)0x00000048U) /*!< Auto-polling on-going */ |
| #define HAL_OSPI_STATE_BUSY_MEM_MAPPED ((uint32_t)0x00000088U) /*!< Memory-mapped on-going */ |
| #define HAL_OSPI_STATE_ABORT ((uint32_t)0x00000100U) /*!< Abort on-going */ |
| #define HAL_OSPI_STATE_ERROR ((uint32_t)0x00000200U) /*!< Blocking error, driver should be re-initialized */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_ErrorCode OSPI Error Code |
| * @{ |
| */ |
| #define HAL_OSPI_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */ |
| #define HAL_OSPI_ERROR_TIMEOUT ((uint32_t)0x00000001U) /*!< Timeout error */ |
| #define HAL_OSPI_ERROR_TRANSFER ((uint32_t)0x00000002U) /*!< Transfer error */ |
| #define HAL_OSPI_ERROR_DMA ((uint32_t)0x00000004U) /*!< DMA transfer error */ |
| #define HAL_OSPI_ERROR_INVALID_PARAM ((uint32_t)0x00000008U) /*!< Invalid parameters error */ |
| #define HAL_OSPI_ERROR_INVALID_SEQUENCE ((uint32_t)0x00000010U) /*!< Sequence of the state machine is incorrect */ |
| #if defined (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) |
| #define HAL_OSPI_ERROR_INVALID_CALLBACK ((uint32_t)0x00000020U) /*!< Invalid callback error */ |
| #endif /* (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U)*/ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_DualQuad OSPI Dual-Quad |
| * @{ |
| */ |
| #define HAL_OSPI_DUALQUAD_DISABLE ((uint32_t)0x00000000U) /*!< Dual-Quad mode disabled */ |
| #define HAL_OSPI_DUALQUAD_ENABLE ((uint32_t)OCTOSPI_CR_DQM) /*!< Dual-Quad mode enabled */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_MemoryType OSPI Memory Type |
| * @{ |
| */ |
| #define HAL_OSPI_MEMTYPE_MICRON ((uint32_t)0x00000000U) /*!< Micron mode */ |
| #define HAL_OSPI_MEMTYPE_MACRONIX ((uint32_t)OCTOSPI_DCR1_MTYP_0) /*!< Macronix mode */ |
| #define HAL_OSPI_MEMTYPE_APMEMORY ((uint32_t)OCTOSPI_DCR1_MTYP_1) /*!< AP Memory mode */ |
| #define HAL_OSPI_MEMTYPE_MACRONIX_RAM ((uint32_t)(OCTOSPI_DCR1_MTYP_1 | OCTOSPI_DCR1_MTYP_0)) /*!< Macronix RAM mode */ |
| #define HAL_OSPI_MEMTYPE_HYPERBUS ((uint32_t)OCTOSPI_DCR1_MTYP_2) /*!< Hyperbus mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_FreeRunningClock OSPI Free Running Clock |
| * @{ |
| */ |
| #define HAL_OSPI_FREERUNCLK_DISABLE ((uint32_t)0x00000000U) /*!< CLK is not free running */ |
| #define HAL_OSPI_FREERUNCLK_ENABLE ((uint32_t)OCTOSPI_DCR1_FRCK) /*!< CLK is free running (always provided) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_ClockMode OSPI Clock Mode |
| * @{ |
| */ |
| #define HAL_OSPI_CLOCK_MODE_0 ((uint32_t)0x00000000U) /*!< CLK must stay low while nCS is high */ |
| #define HAL_OSPI_CLOCK_MODE_3 ((uint32_t)OCTOSPI_DCR1_CKMODE) /*!< CLK must stay high while nCS is high */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_WrapSize OSPI Wrap-Size |
| * @{ |
| */ |
| #define HAL_OSPI_WRAP_NOT_SUPPORTED ((uint32_t)0x00000000U) /*!< wrapped reads are not supported by the memory */ |
| #define HAL_OSPI_WRAP_16_BYTES ((uint32_t)OCTOSPI_DCR2_WRAPSIZE_1) /*!< external memory supports wrap size of 16 bytes */ |
| #define HAL_OSPI_WRAP_32_BYTES ((uint32_t)(OCTOSPI_DCR2_WRAPSIZE_0 | OCTOSPI_DCR2_WRAPSIZE_1)) /*!< external memory supports wrap size of 32 bytes */ |
| #define HAL_OSPI_WRAP_64_BYTES ((uint32_t)OCTOSPI_DCR2_WRAPSIZE_2) /*!< external memory supports wrap size of 64 bytes */ |
| #define HAL_OSPI_WRAP_128_BYTES ((uint32_t)(OCTOSPI_DCR2_WRAPSIZE_0 | OCTOSPI_DCR2_WRAPSIZE_2)) /*!< external memory supports wrap size of 128 bytes */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_SampleShifting OSPI Sample Shifting |
| * @{ |
| */ |
| #define HAL_OSPI_SAMPLE_SHIFTING_NONE ((uint32_t)0x00000000U) /*!< No shift */ |
| #define HAL_OSPI_SAMPLE_SHIFTING_HALFCYCLE ((uint32_t)OCTOSPI_TCR_SSHIFT) /*!< 1/2 cycle shift */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_DelayHoldQuarterCycle OSPI Delay Hold Quarter Cycle |
| * @{ |
| */ |
| #define HAL_OSPI_DHQC_DISABLE ((uint32_t)0x00000000U) /*!< No Delay */ |
| #define HAL_OSPI_DHQC_ENABLE ((uint32_t)OCTOSPI_TCR_DHQC) /*!< Delay Hold 1/4 cycle */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_DelayBlockBypass OSPI Delay Block Bypaas |
| * @{ |
| */ |
| #define HAL_OSPI_DELAY_BLOCK_USED ((uint32_t)0x00000000U) /*!< Sampling clock is delayed by the delay block */ |
| #define HAL_OSPI_DELAY_BLOCK_BYPASSED ((uint32_t)OCTOSPI_DCR1_DLYBYP) /*!< Delay block is bypassed */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_OperationType OSPI Operation Type |
| * @{ |
| */ |
| #define HAL_OSPI_OPTYPE_COMMON_CFG ((uint32_t)0x00000000U) /*!< Common configuration (indirect or auto-polling mode) */ |
| #define HAL_OSPI_OPTYPE_READ_CFG ((uint32_t)0x00000001U) /*!< Read configuration (memory-mapped mode) */ |
| #define HAL_OSPI_OPTYPE_WRITE_CFG ((uint32_t)0x00000002U) /*!< Write configuration (memory-mapped mode) */ |
| #define HAL_OSPI_OPTYPE_WRAP_CFG ((uint32_t)0x00000003U) /*!< Wrap configuration (memory-mapped mode) */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_FlashID OSPI Flash Id |
| * @{ |
| */ |
| #define HAL_OSPI_FLASH_ID_1 ((uint32_t)0x00000000U) /*!< FLASH 1 selected */ |
| #define HAL_OSPI_FLASH_ID_2 ((uint32_t)OCTOSPI_CR_FSEL) /*!< FLASH 2 selected */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_InstructionMode OSPI Instruction Mode |
| * @{ |
| */ |
| #define HAL_OSPI_INSTRUCTION_NONE ((uint32_t)0x00000000U) /*!< No instruction */ |
| #define HAL_OSPI_INSTRUCTION_1_LINE ((uint32_t)OCTOSPI_CCR_IMODE_0) /*!< Instruction on a single line */ |
| #define HAL_OSPI_INSTRUCTION_2_LINES ((uint32_t)OCTOSPI_CCR_IMODE_1) /*!< Instruction on two lines */ |
| #define HAL_OSPI_INSTRUCTION_4_LINES ((uint32_t)(OCTOSPI_CCR_IMODE_0 | OCTOSPI_CCR_IMODE_1)) /*!< Instruction on four lines */ |
| #define HAL_OSPI_INSTRUCTION_8_LINES ((uint32_t)OCTOSPI_CCR_IMODE_2) /*!< Instruction on eight lines */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_InstructionSize OSPI Instruction Size |
| * @{ |
| */ |
| #define HAL_OSPI_INSTRUCTION_8_BITS ((uint32_t)0x00000000U) /*!< 8-bit instruction */ |
| #define HAL_OSPI_INSTRUCTION_16_BITS ((uint32_t)OCTOSPI_CCR_ISIZE_0) /*!< 16-bit instruction */ |
| #define HAL_OSPI_INSTRUCTION_24_BITS ((uint32_t)OCTOSPI_CCR_ISIZE_1) /*!< 24-bit instruction */ |
| #define HAL_OSPI_INSTRUCTION_32_BITS ((uint32_t)OCTOSPI_CCR_ISIZE) /*!< 32-bit instruction */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_InstructionDtrMode OSPI Instruction DTR Mode |
| * @{ |
| */ |
| #define HAL_OSPI_INSTRUCTION_DTR_DISABLE ((uint32_t)0x00000000U) /*!< DTR mode disabled for instruction phase */ |
| #define HAL_OSPI_INSTRUCTION_DTR_ENABLE ((uint32_t)OCTOSPI_CCR_IDTR) /*!< DTR mode enabled for instruction phase */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AddressMode OSPI Address Mode |
| * @{ |
| */ |
| #define HAL_OSPI_ADDRESS_NONE ((uint32_t)0x00000000U) /*!< No address */ |
| #define HAL_OSPI_ADDRESS_1_LINE ((uint32_t)OCTOSPI_CCR_ADMODE_0) /*!< Address on a single line */ |
| #define HAL_OSPI_ADDRESS_2_LINES ((uint32_t)OCTOSPI_CCR_ADMODE_1) /*!< Address on two lines */ |
| #define HAL_OSPI_ADDRESS_4_LINES ((uint32_t)(OCTOSPI_CCR_ADMODE_0 | OCTOSPI_CCR_ADMODE_1)) /*!< Address on four lines */ |
| #define HAL_OSPI_ADDRESS_8_LINES ((uint32_t)OCTOSPI_CCR_ADMODE_2) /*!< Address on eight lines */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AddressSize OSPI Address Size |
| * @{ |
| */ |
| #define HAL_OSPI_ADDRESS_8_BITS ((uint32_t)0x00000000U) /*!< 8-bit address */ |
| #define HAL_OSPI_ADDRESS_16_BITS ((uint32_t)OCTOSPI_CCR_ADSIZE_0) /*!< 16-bit address */ |
| #define HAL_OSPI_ADDRESS_24_BITS ((uint32_t)OCTOSPI_CCR_ADSIZE_1) /*!< 24-bit address */ |
| #define HAL_OSPI_ADDRESS_32_BITS ((uint32_t)OCTOSPI_CCR_ADSIZE) /*!< 32-bit address */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AddressDtrMode OSPI Address DTR Mode |
| * @{ |
| */ |
| #define HAL_OSPI_ADDRESS_DTR_DISABLE ((uint32_t)0x00000000U) /*!< DTR mode disabled for address phase */ |
| #define HAL_OSPI_ADDRESS_DTR_ENABLE ((uint32_t)OCTOSPI_CCR_ADDTR) /*!< DTR mode enabled for address phase */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AlternateBytesMode OSPI Alternate Bytes Mode |
| * @{ |
| */ |
| #define HAL_OSPI_ALTERNATE_BYTES_NONE ((uint32_t)0x00000000U) /*!< No alternate bytes */ |
| #define HAL_OSPI_ALTERNATE_BYTES_1_LINE ((uint32_t)OCTOSPI_CCR_ABMODE_0) /*!< Alternate bytes on a single line */ |
| #define HAL_OSPI_ALTERNATE_BYTES_2_LINES ((uint32_t)OCTOSPI_CCR_ABMODE_1) /*!< Alternate bytes on two lines */ |
| #define HAL_OSPI_ALTERNATE_BYTES_4_LINES ((uint32_t)(OCTOSPI_CCR_ABMODE_0 | OCTOSPI_CCR_ABMODE_1)) /*!< Alternate bytes on four lines */ |
| #define HAL_OSPI_ALTERNATE_BYTES_8_LINES ((uint32_t)OCTOSPI_CCR_ABMODE_2) /*!< Alternate bytes on eight lines */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AlternateBytesSize OSPI Alternate Bytes Size |
| * @{ |
| */ |
| #define HAL_OSPI_ALTERNATE_BYTES_8_BITS ((uint32_t)0x00000000U) /*!< 8-bit alternate bytes */ |
| #define HAL_OSPI_ALTERNATE_BYTES_16_BITS ((uint32_t)OCTOSPI_CCR_ABSIZE_0) /*!< 16-bit alternate bytes */ |
| #define HAL_OSPI_ALTERNATE_BYTES_24_BITS ((uint32_t)OCTOSPI_CCR_ABSIZE_1) /*!< 24-bit alternate bytes */ |
| #define HAL_OSPI_ALTERNATE_BYTES_32_BITS ((uint32_t)OCTOSPI_CCR_ABSIZE) /*!< 32-bit alternate bytes */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AlternateBytesDtrMode OSPI Alternate Bytes DTR Mode |
| * @{ |
| */ |
| #define HAL_OSPI_ALTERNATE_BYTES_DTR_DISABLE ((uint32_t)0x00000000U) /*!< DTR mode disabled for alternate bytes phase */ |
| #define HAL_OSPI_ALTERNATE_BYTES_DTR_ENABLE ((uint32_t)OCTOSPI_CCR_ABDTR) /*!< DTR mode enabled for alternate bytes phase */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_DataMode OSPI Data Mode |
| * @{ |
| */ |
| #define HAL_OSPI_DATA_NONE ((uint32_t)0x00000000U) /*!< No data */ |
| #define HAL_OSPI_DATA_1_LINE ((uint32_t)OCTOSPI_CCR_DMODE_0) /*!< Data on a single line */ |
| #define HAL_OSPI_DATA_2_LINES ((uint32_t)OCTOSPI_CCR_DMODE_1) /*!< Data on two lines */ |
| #define HAL_OSPI_DATA_4_LINES ((uint32_t)(OCTOSPI_CCR_DMODE_0 | OCTOSPI_CCR_DMODE_1)) /*!< Data on four lines */ |
| #define HAL_OSPI_DATA_8_LINES ((uint32_t)OCTOSPI_CCR_DMODE_2) /*!< Data on eight lines */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_DataDtrMode OSPI Data DTR Mode |
| * @{ |
| */ |
| #define HAL_OSPI_DATA_DTR_DISABLE ((uint32_t)0x00000000U) /*!< DTR mode disabled for data phase */ |
| #define HAL_OSPI_DATA_DTR_ENABLE ((uint32_t)OCTOSPI_CCR_DDTR) /*!< DTR mode enabled for data phase */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_DQSMode OSPI DQS Mode |
| * @{ |
| */ |
| #define HAL_OSPI_DQS_DISABLE ((uint32_t)0x00000000U) /*!< DQS disabled */ |
| #define HAL_OSPI_DQS_ENABLE ((uint32_t)OCTOSPI_CCR_DQSE) /*!< DQS enabled */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_SIOOMode OSPI SIOO Mode |
| * @{ |
| */ |
| #define HAL_OSPI_SIOO_INST_EVERY_CMD ((uint32_t)0x00000000U) /*!< Send instruction on every transaction */ |
| #define HAL_OSPI_SIOO_INST_ONLY_FIRST_CMD ((uint32_t)OCTOSPI_CCR_SIOO) /*!< Send instruction only for the first command */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_WriteZeroLatency OSPI Hyperbus Write Zero Latency Activation |
| * @{ |
| */ |
| #define HAL_OSPI_LATENCY_ON_WRITE ((uint32_t)0x00000000U) /*!< Latency on write accesses */ |
| #define HAL_OSPI_NO_LATENCY_ON_WRITE ((uint32_t)OCTOSPI_HLCR_WZL) /*!< No latency on write accesses */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_LatencyMode OSPI Hyperbus Latency Mode |
| * @{ |
| */ |
| #define HAL_OSPI_VARIABLE_LATENCY ((uint32_t)0x00000000U) /*!< Variable initial latency */ |
| #define HAL_OSPI_FIXED_LATENCY ((uint32_t)OCTOSPI_HLCR_LM) /*!< Fixed latency */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AddressSpace OSPI Hyperbus Address Space |
| * @{ |
| */ |
| #define HAL_OSPI_MEMORY_ADDRESS_SPACE ((uint32_t)0x00000000U) /*!< HyperBus memory mode */ |
| #define HAL_OSPI_REGISTER_ADDRESS_SPACE ((uint32_t)OCTOSPI_DCR1_MTYP_0) /*!< HyperBus register mode */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_MatchMode OSPI Match Mode |
| * @{ |
| */ |
| #define HAL_OSPI_MATCH_MODE_AND ((uint32_t)0x00000000U) /*!< AND match mode between unmasked bits */ |
| #define HAL_OSPI_MATCH_MODE_OR ((uint32_t)OCTOSPI_CR_PMM) /*!< OR match mode between unmasked bits */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_AutomaticStop OSPI Automatic Stop |
| * @{ |
| */ |
| #define HAL_OSPI_AUTOMATIC_STOP_DISABLE ((uint32_t)0x00000000U) /*!< AutoPolling stops only with abort or OSPI disabling */ |
| #define HAL_OSPI_AUTOMATIC_STOP_ENABLE ((uint32_t)OCTOSPI_CR_APMS) /*!< AutoPolling stops as soon as there is a match */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_TimeOutActivation OSPI Timeout Activation |
| * @{ |
| */ |
| #define HAL_OSPI_TIMEOUT_COUNTER_DISABLE ((uint32_t)0x00000000U) /*!< Timeout counter disabled, nCS remains active */ |
| #define HAL_OSPI_TIMEOUT_COUNTER_ENABLE ((uint32_t)OCTOSPI_CR_TCEN) /*!< Timeout counter enabled, nCS released when timeout expires */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_Flags OSPI Flags |
| * @{ |
| */ |
| #define HAL_OSPI_FLAG_BUSY OCTOSPI_SR_BUSY /*!< Busy flag: operation is ongoing */ |
| #define HAL_OSPI_FLAG_TO OCTOSPI_SR_TOF /*!< Timeout flag: timeout occurs in memory-mapped mode */ |
| #define HAL_OSPI_FLAG_SM OCTOSPI_SR_SMF /*!< Status match flag: received data matches in autopolling mode */ |
| #define HAL_OSPI_FLAG_FT OCTOSPI_SR_FTF /*!< Fifo threshold flag: Fifo threshold reached or data left after read from memory is complete */ |
| #define HAL_OSPI_FLAG_TC OCTOSPI_SR_TCF /*!< Transfer complete flag: programmed number of data have been transferred or the transfer has been aborted */ |
| #define HAL_OSPI_FLAG_TE OCTOSPI_SR_TEF /*!< Transfer error flag: invalid address is being accessed */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_Interrupts OSPI Interrupts |
| * @{ |
| */ |
| #define HAL_OSPI_IT_TO OCTOSPI_CR_TOIE /*!< Interrupt on the timeout flag */ |
| #define HAL_OSPI_IT_SM OCTOSPI_CR_SMIE /*!< Interrupt on the status match flag */ |
| #define HAL_OSPI_IT_FT OCTOSPI_CR_FTIE /*!< Interrupt on the fifo threshold flag */ |
| #define HAL_OSPI_IT_TC OCTOSPI_CR_TCIE /*!< Interrupt on the transfer complete flag */ |
| #define HAL_OSPI_IT_TE OCTOSPI_CR_TEIE /*!< Interrupt on the transfer error flag */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPI_Timeout_definition OSPI Timeout definition |
| * @{ |
| */ |
| #define HAL_OSPI_TIMEOUT_DEFAULT_VALUE ((uint32_t)5000U) /* 5 s */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OSPIM_IOPort OSPI IO Manager IO Port |
| * @{ |
| */ |
| #define HAL_OSPIM_IOPORT_NONE ((uint32_t)0x00000000U) /*!< IOs not used */ |
| #define HAL_OSPIM_IOPORT_1_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x1U)) /*!< Port 1 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_1_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x1U)) /*!< Port 1 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_2_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x2U)) /*!< Port 2 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_2_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x2U)) /*!< Port 2 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_3_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x3U)) /*!< Port 3 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_3_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x3U)) /*!< Port 3 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_4_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x4U)) /*!< Port 4 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_4_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x4U)) /*!< Port 4 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_5_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x5U)) /*!< Port 5 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_5_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x5U)) /*!< Port 5 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_6_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x6U)) /*!< Port 6 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_6_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x6U)) /*!< Port 6 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_7_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x7U)) /*!< Port 7 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_7_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x7U)) /*!< Port 7 - IO[7:4] */ |
| #define HAL_OSPIM_IOPORT_8_LOW ((uint32_t)(OCTOSPIM_PCR_IOLEN | 0x8U)) /*!< Port 8 - IO[3:0] */ |
| #define HAL_OSPIM_IOPORT_8_HIGH ((uint32_t)(OCTOSPIM_PCR_IOHEN | 0x8U)) /*!< Port 8 - IO[7:4] */ |
| /** |
| * @} |
| */ |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| /** @defgroup OSPI_Exported_Macros OSPI Exported Macros |
| * @{ |
| */ |
| /** @brief Reset OSPI handle state. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @retval None |
| */ |
| #if defined (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) |
| #define __HAL_OSPI_RESET_HANDLE_STATE(__HANDLE__) do { \ |
| (__HANDLE__)->State = HAL_OSPI_STATE_RESET; \ |
| (__HANDLE__)->MspInitCallback = NULL; \ |
| (__HANDLE__)->MspDeInitCallback = NULL; \ |
| } while(0) |
| #else |
| #define __HAL_OSPI_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_OSPI_STATE_RESET) |
| #endif /* (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) */ |
| |
| /** @brief Enable the OSPI peripheral. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @retval None |
| */ |
| #define __HAL_OSPI_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR, OCTOSPI_CR_EN) |
| |
| /** @brief Disable the OSPI peripheral. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @retval None |
| */ |
| #define __HAL_OSPI_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR, OCTOSPI_CR_EN) |
| |
| /** @brief Enable the specified OSPI interrupt. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @param __INTERRUPT__ specifies the OSPI interrupt source to enable. |
| * This parameter can be one of the following values: |
| * @arg HAL_OSPI_IT_TO: OSPI Timeout interrupt |
| * @arg HAL_OSPI_IT_SM: OSPI Status match interrupt |
| * @arg HAL_OSPI_IT_FT: OSPI FIFO threshold interrupt |
| * @arg HAL_OSPI_IT_TC: OSPI Transfer complete interrupt |
| * @arg HAL_OSPI_IT_TE: OSPI Transfer error interrupt |
| * @retval None |
| */ |
| #define __HAL_OSPI_ENABLE_IT(__HANDLE__, __INTERRUPT__) SET_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) |
| |
| |
| /** @brief Disable the specified OSPI interrupt. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @param __INTERRUPT__ specifies the OSPI interrupt source to disable. |
| * This parameter can be one of the following values: |
| * @arg HAL_OSPI_IT_TO: OSPI Timeout interrupt |
| * @arg HAL_OSPI_IT_SM: OSPI Status match interrupt |
| * @arg HAL_OSPI_IT_FT: OSPI FIFO threshold interrupt |
| * @arg HAL_OSPI_IT_TC: OSPI Transfer complete interrupt |
| * @arg HAL_OSPI_IT_TE: OSPI Transfer error interrupt |
| * @retval None |
| */ |
| #define __HAL_OSPI_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) |
| |
| /** @brief Check whether the specified OSPI interrupt source is enabled or not. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @param __INTERRUPT__ specifies the OSPI interrupt source to check. |
| * This parameter can be one of the following values: |
| * @arg HAL_OSPI_IT_TO: OSPI Timeout interrupt |
| * @arg HAL_OSPI_IT_SM: OSPI Status match interrupt |
| * @arg HAL_OSPI_IT_FT: OSPI FIFO threshold interrupt |
| * @arg HAL_OSPI_IT_TC: OSPI Transfer complete interrupt |
| * @arg HAL_OSPI_IT_TE: OSPI Transfer error interrupt |
| * @retval The new state of __INTERRUPT__ (TRUE or FALSE). |
| */ |
| #define __HAL_OSPI_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (READ_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))\ |
| == (__INTERRUPT__)) |
| |
| /** |
| * @brief Check whether the selected OSPI flag is set or not. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @param __FLAG__ specifies the OSPI flag to check. |
| * This parameter can be one of the following values: |
| * @arg HAL_OSPI_FLAG_BUSY: OSPI Busy flag |
| * @arg HAL_OSPI_FLAG_TO: OSPI Timeout flag |
| * @arg HAL_OSPI_FLAG_SM: OSPI Status match flag |
| * @arg HAL_OSPI_FLAG_FT: OSPI FIFO threshold flag |
| * @arg HAL_OSPI_FLAG_TC: OSPI Transfer complete flag |
| * @arg HAL_OSPI_FLAG_TE: OSPI Transfer error flag |
| * @retval None |
| */ |
| #define __HAL_OSPI_GET_FLAG(__HANDLE__, __FLAG__) ((READ_BIT((__HANDLE__)->Instance->SR, (__FLAG__)) \ |
| != 0U) ? SET : RESET) |
| |
| /** @brief Clears the specified OSPI's flag status. |
| * @param __HANDLE__ specifies the OSPI Handle. |
| * @param __FLAG__ specifies the OSPI clear register flag that needs to be set |
| * This parameter can be one of the following values: |
| * @arg HAL_OSPI_FLAG_TO: OSPI Timeout flag |
| * @arg HAL_OSPI_FLAG_SM: OSPI Status match flag |
| * @arg HAL_OSPI_FLAG_TC: OSPI Transfer complete flag |
| * @arg HAL_OSPI_FLAG_TE: OSPI Transfer error flag |
| * @retval None |
| */ |
| #define __HAL_OSPI_CLEAR_FLAG(__HANDLE__, __FLAG__) WRITE_REG((__HANDLE__)->Instance->FCR, (__FLAG__)) |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup OSPI_Exported_Functions |
| * @{ |
| */ |
| |
| /* Initialization/de-initialization functions ********************************/ |
| /** @addtogroup OSPI_Exported_Functions_Group1 |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_OSPI_Init (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_MspInit (OSPI_HandleTypeDef *hospi); |
| HAL_StatusTypeDef HAL_OSPI_DeInit (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_MspDeInit (OSPI_HandleTypeDef *hospi); |
| |
| /** |
| * @} |
| */ |
| |
| /* IO operation functions *****************************************************/ |
| /** @addtogroup OSPI_Exported_Functions_Group2 |
| * @{ |
| */ |
| /* OSPI IRQ handler function */ |
| void HAL_OSPI_IRQHandler (OSPI_HandleTypeDef *hospi); |
| |
| /* OSPI command configuration functions */ |
| HAL_StatusTypeDef HAL_OSPI_Command(OSPI_HandleTypeDef *hospi, OSPI_RegularCmdTypeDef *cmd, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_OSPI_Command_IT(OSPI_HandleTypeDef *hospi, OSPI_RegularCmdTypeDef *cmd); |
| HAL_StatusTypeDef HAL_OSPI_HyperbusCfg(OSPI_HandleTypeDef *hospi, OSPI_HyperbusCfgTypeDef *cfg, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_OSPI_HyperbusCmd(OSPI_HandleTypeDef *hospi, OSPI_HyperbusCmdTypeDef *cmd, uint32_t Timeout); |
| |
| /* OSPI indirect mode functions */ |
| HAL_StatusTypeDef HAL_OSPI_Transmit(OSPI_HandleTypeDef *hospi, uint8_t *pData, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_OSPI_Receive(OSPI_HandleTypeDef *hospi, uint8_t *pData, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_OSPI_Transmit_IT(OSPI_HandleTypeDef *hospi, uint8_t *pData); |
| HAL_StatusTypeDef HAL_OSPI_Receive_IT(OSPI_HandleTypeDef *hospi, uint8_t *pData); |
| HAL_StatusTypeDef HAL_OSPI_Transmit_DMA(OSPI_HandleTypeDef *hospi, uint8_t *pData); |
| HAL_StatusTypeDef HAL_OSPI_Receive_DMA(OSPI_HandleTypeDef *hospi, uint8_t *pData); |
| |
| /* OSPI status flag polling mode functions */ |
| HAL_StatusTypeDef HAL_OSPI_AutoPolling(OSPI_HandleTypeDef *hospi, OSPI_AutoPollingTypeDef *cfg, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_OSPI_AutoPolling_IT(OSPI_HandleTypeDef *hospi, OSPI_AutoPollingTypeDef *cfg); |
| |
| /* OSPI memory-mapped mode functions */ |
| HAL_StatusTypeDef HAL_OSPI_MemoryMapped (OSPI_HandleTypeDef *hospi, OSPI_MemoryMappedTypeDef *cfg); |
| |
| /* Callback functions in non-blocking modes ***********************************/ |
| void HAL_OSPI_ErrorCallback (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_AbortCpltCallback (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_FifoThresholdCallback(OSPI_HandleTypeDef *hospi); |
| |
| /* OSPI indirect mode functions */ |
| void HAL_OSPI_CmdCpltCallback (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_RxCpltCallback (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_TxCpltCallback (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_RxHalfCpltCallback (OSPI_HandleTypeDef *hospi); |
| void HAL_OSPI_TxHalfCpltCallback (OSPI_HandleTypeDef *hospi); |
| |
| /* OSPI status flag polling mode functions */ |
| void HAL_OSPI_StatusMatchCallback (OSPI_HandleTypeDef *hospi); |
| |
| /* OSPI memory-mapped mode functions */ |
| void HAL_OSPI_TimeOutCallback (OSPI_HandleTypeDef *hospi); |
| |
| #if defined (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) |
| /* OSPI callback registering/unregistering */ |
| HAL_StatusTypeDef HAL_OSPI_RegisterCallback(OSPI_HandleTypeDef *hospi, HAL_OSPI_CallbackIDTypeDef CallbackID, |
| pOSPI_CallbackTypeDef pCallback); |
| HAL_StatusTypeDef HAL_OSPI_UnRegisterCallback(OSPI_HandleTypeDef *hospi, HAL_OSPI_CallbackIDTypeDef CallbackID); |
| #endif /* (USE_HAL_OSPI_REGISTER_CALLBACKS) && (USE_HAL_OSPI_REGISTER_CALLBACKS == 1U) */ |
| /** |
| * @} |
| */ |
| |
| /* Peripheral Control and State functions ************************************/ |
| /** @addtogroup OSPI_Exported_Functions_Group3 |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_OSPI_Abort (OSPI_HandleTypeDef *hospi); |
| HAL_StatusTypeDef HAL_OSPI_Abort_IT (OSPI_HandleTypeDef *hospi); |
| HAL_StatusTypeDef HAL_OSPI_SetFifoThreshold (OSPI_HandleTypeDef *hospi, uint32_t Threshold); |
| uint32_t HAL_OSPI_GetFifoThreshold (OSPI_HandleTypeDef *hospi); |
| HAL_StatusTypeDef HAL_OSPI_SetTimeout (OSPI_HandleTypeDef *hospi, uint32_t Timeout); |
| uint32_t HAL_OSPI_GetError (OSPI_HandleTypeDef *hospi); |
| uint32_t HAL_OSPI_GetState (OSPI_HandleTypeDef *hospi); |
| |
| /** |
| * @} |
| */ |
| |
| /* OSPI IO Manager configuration function ************************************/ |
| /** @addtogroup OSPI_Exported_Functions_Group4 |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_OSPIM_Config(OSPI_HandleTypeDef *hospi, OSPIM_CfgTypeDef *cfg, uint32_t Timeout); |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| /* End of exported functions -------------------------------------------------*/ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** |
| @cond 0 |
| */ |
| #define IS_OSPI_FIFO_THRESHOLD(THRESHOLD) (((THRESHOLD) >= 1U) && ((THRESHOLD) <= 32U)) |
| |
| #define IS_OSPI_DUALQUAD_MODE(MODE) (((MODE) == HAL_OSPI_DUALQUAD_DISABLE) || \ |
| ((MODE) == HAL_OSPI_DUALQUAD_ENABLE)) |
| |
| #define IS_OSPI_MEMORY_TYPE(TYPE) (((TYPE) == HAL_OSPI_MEMTYPE_MICRON) || \ |
| ((TYPE) == HAL_OSPI_MEMTYPE_MACRONIX) || \ |
| ((TYPE) == HAL_OSPI_MEMTYPE_APMEMORY) || \ |
| ((TYPE) == HAL_OSPI_MEMTYPE_MACRONIX_RAM) || \ |
| ((TYPE) == HAL_OSPI_MEMTYPE_HYPERBUS)) |
| |
| #define IS_OSPI_DEVICE_SIZE(SIZE) (((SIZE) >= 1U) && ((SIZE) <= 32U)) |
| |
| #define IS_OSPI_CS_HIGH_TIME(TIME) (((TIME) >= 1U) && ((TIME) <= 8U)) |
| |
| #define IS_OSPI_FREE_RUN_CLK(CLK) (((CLK) == HAL_OSPI_FREERUNCLK_DISABLE) || \ |
| ((CLK) == HAL_OSPI_FREERUNCLK_ENABLE)) |
| |
| #define IS_OSPI_CLOCK_MODE(MODE) (((MODE) == HAL_OSPI_CLOCK_MODE_0) || \ |
| ((MODE) == HAL_OSPI_CLOCK_MODE_3)) |
| |
| #define IS_OSPI_WRAP_SIZE(SIZE) (((SIZE) == HAL_OSPI_WRAP_NOT_SUPPORTED) || \ |
| ((SIZE) == HAL_OSPI_WRAP_16_BYTES) || \ |
| ((SIZE) == HAL_OSPI_WRAP_32_BYTES) || \ |
| ((SIZE) == HAL_OSPI_WRAP_64_BYTES) || \ |
| ((SIZE) == HAL_OSPI_WRAP_128_BYTES)) |
| |
| #define IS_OSPI_CLK_PRESCALER(PRESCALER) (((PRESCALER) >= 1U) && ((PRESCALER) <= 256U)) |
| |
| #define IS_OSPI_SAMPLE_SHIFTING(CYCLE) (((CYCLE) == HAL_OSPI_SAMPLE_SHIFTING_NONE) || \ |
| ((CYCLE) == HAL_OSPI_SAMPLE_SHIFTING_HALFCYCLE)) |
| |
| #define IS_OSPI_DHQC(CYCLE) (((CYCLE) == HAL_OSPI_DHQC_DISABLE) || \ |
| ((CYCLE) == HAL_OSPI_DHQC_ENABLE)) |
| |
| #define IS_OSPI_OPERATION_TYPE(TYPE) (((TYPE) == HAL_OSPI_OPTYPE_COMMON_CFG) || \ |
| ((TYPE) == HAL_OSPI_OPTYPE_READ_CFG) || \ |
| ((TYPE) == HAL_OSPI_OPTYPE_WRITE_CFG) || \ |
| ((TYPE) == HAL_OSPI_OPTYPE_WRAP_CFG)) |
| |
| #define IS_OSPI_FLASH_ID(FLASHID) (((FLASHID) == HAL_OSPI_FLASH_ID_1) || \ |
| ((FLASHID) == HAL_OSPI_FLASH_ID_2)) |
| |
| #define IS_OSPI_INSTRUCTION_MODE(MODE) (((MODE) == HAL_OSPI_INSTRUCTION_NONE) || \ |
| ((MODE) == HAL_OSPI_INSTRUCTION_1_LINE) || \ |
| ((MODE) == HAL_OSPI_INSTRUCTION_2_LINES) || \ |
| ((MODE) == HAL_OSPI_INSTRUCTION_4_LINES) || \ |
| ((MODE) == HAL_OSPI_INSTRUCTION_8_LINES)) |
| |
| #define IS_OSPI_INSTRUCTION_SIZE(SIZE) (((SIZE) == HAL_OSPI_INSTRUCTION_8_BITS) || \ |
| ((SIZE) == HAL_OSPI_INSTRUCTION_16_BITS) || \ |
| ((SIZE) == HAL_OSPI_INSTRUCTION_24_BITS) || \ |
| ((SIZE) == HAL_OSPI_INSTRUCTION_32_BITS)) |
| |
| #define IS_OSPI_INSTRUCTION_DTR_MODE(MODE) (((MODE) == HAL_OSPI_INSTRUCTION_DTR_DISABLE) || \ |
| ((MODE) == HAL_OSPI_INSTRUCTION_DTR_ENABLE)) |
| |
| #define IS_OSPI_ADDRESS_MODE(MODE) (((MODE) == HAL_OSPI_ADDRESS_NONE) || \ |
| ((MODE) == HAL_OSPI_ADDRESS_1_LINE) || \ |
| ((MODE) == HAL_OSPI_ADDRESS_2_LINES) || \ |
| ((MODE) == HAL_OSPI_ADDRESS_4_LINES) || \ |
| ((MODE) == HAL_OSPI_ADDRESS_8_LINES)) |
| |
| #define IS_OSPI_ADDRESS_SIZE(SIZE) (((SIZE) == HAL_OSPI_ADDRESS_8_BITS) || \ |
| ((SIZE) == HAL_OSPI_ADDRESS_16_BITS) || \ |
| ((SIZE) == HAL_OSPI_ADDRESS_24_BITS) || \ |
| ((SIZE) == HAL_OSPI_ADDRESS_32_BITS)) |
| |
| #define IS_OSPI_ADDRESS_DTR_MODE(MODE) (((MODE) == HAL_OSPI_ADDRESS_DTR_DISABLE) || \ |
| ((MODE) == HAL_OSPI_ADDRESS_DTR_ENABLE)) |
| |
| #define IS_OSPI_ALT_BYTES_MODE(MODE) (((MODE) == HAL_OSPI_ALTERNATE_BYTES_NONE) || \ |
| ((MODE) == HAL_OSPI_ALTERNATE_BYTES_1_LINE) || \ |
| ((MODE) == HAL_OSPI_ALTERNATE_BYTES_2_LINES) || \ |
| ((MODE) == HAL_OSPI_ALTERNATE_BYTES_4_LINES) || \ |
| ((MODE) == HAL_OSPI_ALTERNATE_BYTES_8_LINES)) |
| |
| #define IS_OSPI_ALT_BYTES_SIZE(SIZE) (((SIZE) == HAL_OSPI_ALTERNATE_BYTES_8_BITS) || \ |
| ((SIZE) == HAL_OSPI_ALTERNATE_BYTES_16_BITS) || \ |
| ((SIZE) == HAL_OSPI_ALTERNATE_BYTES_24_BITS) || \ |
| ((SIZE) == HAL_OSPI_ALTERNATE_BYTES_32_BITS)) |
| |
| #define IS_OSPI_ALT_BYTES_DTR_MODE(MODE) (((MODE) == HAL_OSPI_ALTERNATE_BYTES_DTR_DISABLE) || \ |
| ((MODE) == HAL_OSPI_ALTERNATE_BYTES_DTR_ENABLE)) |
| |
| #define IS_OSPI_DATA_MODE(MODE) (((MODE) == HAL_OSPI_DATA_NONE) || \ |
| ((MODE) == HAL_OSPI_DATA_1_LINE) || \ |
| ((MODE) == HAL_OSPI_DATA_2_LINES) || \ |
| ((MODE) == HAL_OSPI_DATA_4_LINES) || \ |
| ((MODE) == HAL_OSPI_DATA_8_LINES)) |
| |
| #define IS_OSPI_NUMBER_DATA(NUMBER) ((NUMBER) >= 1U) |
| |
| #define IS_OSPI_DATA_DTR_MODE(MODE) (((MODE) == HAL_OSPI_DATA_DTR_DISABLE) || \ |
| ((MODE) == HAL_OSPI_DATA_DTR_ENABLE)) |
| |
| #define IS_OSPI_DUMMY_CYCLES(NUMBER) ((NUMBER) <= 31U) |
| |
| #define IS_OSPI_DQS_MODE(MODE) (((MODE) == HAL_OSPI_DQS_DISABLE) || \ |
| ((MODE) == HAL_OSPI_DQS_ENABLE)) |
| |
| #define IS_OSPI_SIOO_MODE(MODE) (((MODE) == HAL_OSPI_SIOO_INST_EVERY_CMD) || \ |
| ((MODE) == HAL_OSPI_SIOO_INST_ONLY_FIRST_CMD)) |
| |
| #define IS_OSPI_RW_RECOVERY_TIME(NUMBER) ((NUMBER) <= 255U) |
| |
| #define IS_OSPI_ACCESS_TIME(NUMBER) ((NUMBER) <= 255U) |
| |
| #define IS_OSPI_WRITE_ZERO_LATENCY(MODE) (((MODE) == HAL_OSPI_LATENCY_ON_WRITE) || \ |
| ((MODE) == HAL_OSPI_NO_LATENCY_ON_WRITE)) |
| |
| #define IS_OSPI_LATENCY_MODE(MODE) (((MODE) == HAL_OSPI_VARIABLE_LATENCY) || \ |
| ((MODE) == HAL_OSPI_FIXED_LATENCY)) |
| |
| #define IS_OSPI_ADDRESS_SPACE(SPACE) (((SPACE) == HAL_OSPI_MEMORY_ADDRESS_SPACE) || \ |
| ((SPACE) == HAL_OSPI_REGISTER_ADDRESS_SPACE)) |
| |
| #define IS_OSPI_MATCH_MODE(MODE) (((MODE) == HAL_OSPI_MATCH_MODE_AND) || \ |
| ((MODE) == HAL_OSPI_MATCH_MODE_OR)) |
| |
| #define IS_OSPI_AUTOMATIC_STOP(MODE) (((MODE) == HAL_OSPI_AUTOMATIC_STOP_ENABLE) || \ |
| ((MODE) == HAL_OSPI_AUTOMATIC_STOP_DISABLE)) |
| |
| #define IS_OSPI_INTERVAL(INTERVAL) ((INTERVAL) <= 0xFFFFU) |
| |
| #define IS_OSPI_STATUS_BYTES_SIZE(SIZE) (((SIZE) >= 1U) && ((SIZE) <= 4U)) |
| |
| #define IS_OSPI_TIMEOUT_ACTIVATION(MODE) (((MODE) == HAL_OSPI_TIMEOUT_COUNTER_DISABLE) || \ |
| ((MODE) == HAL_OSPI_TIMEOUT_COUNTER_ENABLE)) |
| |
| #define IS_OSPI_TIMEOUT_PERIOD(PERIOD) ((PERIOD) <= 0xFFFFU) |
| |
| #define IS_OSPI_CS_BOUNDARY(BOUNDARY) ((BOUNDARY) <= 31U) |
| |
| #define IS_OSPI_DLYBYP(MODE) (((MODE) == HAL_OSPI_DELAY_BLOCK_USED) || \ |
| ((MODE) == HAL_OSPI_DELAY_BLOCK_BYPASSED)) |
| |
| #define IS_OSPI_MAXTRAN(NB_BYTES) ((NB_BYTES) <= 255U) |
| |
| #define IS_OSPIM_PORT(NUMBER) (((NUMBER) >= 1U) && ((NUMBER) <= 8U)) |
| |
| #define IS_OSPIM_DQS_PORT(NUMBER) ((NUMBER) <= 8U) |
| |
| #define IS_OSPIM_IO_PORT(PORT) (((PORT) == HAL_OSPIM_IOPORT_NONE) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_1_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_1_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_2_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_2_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_3_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_3_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_4_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_4_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_5_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_5_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_6_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_6_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_7_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_7_HIGH) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_8_LOW) || \ |
| ((PORT) == HAL_OSPIM_IOPORT_8_HIGH)) |
| |
| #define IS_OSPIM_REQ2ACKTIME(TIME) (((TIME) >= 1U) && ((TIME) <= 256U)) |
| /** |
| @endcond |
| */ |
| |
| /* End of private macros -----------------------------------------------------*/ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* OCTOSPI || OCTOSPI1 || OCTOSPI2 */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32H7xx_HAL_OSPI_H */ |
