| /** |
| ****************************************************************************** |
| * @file stm32l1xx_hal_opamp.h |
| * @author MCD Application Team |
| * @brief Header file of OPAMP HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved. |
| * |
| * This software is licensed under terms that can be found in the LICENSE file |
| * in the root directory of this software component. |
| * If no LICENSE file comes with this software, it is provided AS-IS. |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32L1xx_HAL_OPAMP_H |
| #define STM32L1xx_HAL_OPAMP_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| #if defined (STM32L151xCA) || defined (STM32L151xD) || defined (STM32L152xCA) || defined (STM32L152xD) || defined (STM32L162xCA) || defined (STM32L162xD) || defined (STM32L151xE) || defined (STM32L151xDX) || defined (STM32L152xE) || defined (STM32L152xDX) || defined (STM32L162xE) || defined (STM32L162xDX) || defined (STM32L162xC) || defined (STM32L152xC) || defined (STM32L151xC) |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32l1xx_hal_def.h" |
| |
| /** @addtogroup STM32L1xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup OPAMP |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| |
| /** @defgroup OPAMP_Exported_Types OPAMP Exported Types |
| * @{ |
| */ |
| |
| /** |
| * @brief OPAMP Init structure definition |
| */ |
| |
| typedef struct |
| { |
| uint32_t PowerSupplyRange; /*!< Specifies the power supply range: above or under 2.4V. |
| This parameter must be a value of @ref OPAMP_PowerSupplyRange |
| Caution: This parameter is common to all OPAMP instances: a modification of this parameter for the selected OPAMP impacts the other OPAMP instances. */ |
| |
| uint32_t PowerMode; /*!< Specifies the power mode Normal or Low-Power. |
| This parameter must be a value of @ref OPAMP_PowerMode */ |
| |
| uint32_t Mode; /*!< Specifies the OPAMP mode |
| This parameter must be a value of @ref OPAMP_Mode |
| mode is either Standalone or Follower */ |
| |
| uint32_t InvertingInput; /*!< Specifies the inverting input in Standalone mode |
| - In Standalone mode: i.e when mode is OPAMP_STANDALONE_MODE |
| This parameter must be a value of @ref OPAMP_InvertingInput |
| InvertingInput is either VM0 or VM1 |
| - In Follower mode: i.e when mode is OPAMP_FOLLOWER_MODE |
| This parameter is Not Applicable */ |
| |
| uint32_t NonInvertingInput; /*!< Specifies the non inverting input of the opamp: |
| This parameter must be a value of @ref OPAMP_NonInvertingInput |
| Note: Non-inverting input availability depends on OPAMP instance: |
| OPAMP1: Non-inverting input is either IO0, DAC_Channel1 |
| OPAMP2: Non-inverting input is either IO0, DAC_Channel1, DAC_Channel2 |
| OPAMP3: Non-inverting input is either IO0, DAC_Channel2 (OPAMP3 availability depends on STM32L1 devices) */ |
| |
| uint32_t UserTrimming; /*!< Specifies the trimming mode |
| This parameter must be a value of @ref OPAMP_UserTrimming |
| UserTrimming is either factory or user trimming. |
| Caution: This parameter is common to all OPAMP instances: a modification of this parameter for the selected OPAMP impacts the other OPAMP instances. */ |
| |
| uint32_t TrimmingValueP; /*!< Specifies the offset trimming value (PMOS) |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) |
| 16 is typical default value */ |
| |
| uint32_t TrimmingValueN; /*!< Specifies the offset trimming value (NMOS) |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) |
| 16 is typical default value */ |
| |
| uint32_t TrimmingValuePLowPower; /*!< Specifies the offset trimming value (PMOS) |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) |
| 16 is typical default value */ |
| |
| uint32_t TrimmingValueNLowPower; /*!< Specifies the offset trimming value (NMOS) |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) |
| 16 is typical default value */ |
| |
| }OPAMP_InitTypeDef; |
| |
| /** |
| * @brief HAL State structures definition |
| */ |
| |
| typedef enum |
| { |
| HAL_OPAMP_STATE_RESET = 0x00000000, /*!< OPAMP is not yet Initialized */ |
| |
| HAL_OPAMP_STATE_READY = 0x00000001, /*!< OPAMP is initialized and ready for use */ |
| HAL_OPAMP_STATE_CALIBBUSY = 0x00000002, /*!< OPAMP is enabled in auto calibration mode */ |
| |
| HAL_OPAMP_STATE_BUSY = 0x00000004, /*!< OPAMP is enabled and running in normal mode */ |
| HAL_OPAMP_STATE_BUSYLOCKED = 0x00000005 /*!< OPAMP is locked |
| only system reset allows reconfiguring the opamp. */ |
| |
| }HAL_OPAMP_StateTypeDef; |
| |
| /** |
| * @brief OPAMP Handle Structure definition |
| */ |
| #if (USE_HAL_OPAMP_REGISTER_CALLBACKS == 1) |
| typedef struct __OPAMP_HandleTypeDef |
| #else |
| typedef struct |
| #endif /* USE_HAL_OPAMP_REGISTER_CALLBACKS */ |
| { |
| OPAMP_TypeDef *Instance; /*!< OPAMP instance's registers base address */ |
| OPAMP_InitTypeDef Init; /*!< OPAMP required parameters */ |
| HAL_StatusTypeDef Status; /*!< OPAMP peripheral status */ |
| HAL_LockTypeDef Lock; /*!< Locking object */ |
| __IO HAL_OPAMP_StateTypeDef State; /*!< OPAMP communication state */ |
| |
| #if (USE_HAL_OPAMP_REGISTER_CALLBACKS == 1) |
| void (* MspInitCallback) (struct __OPAMP_HandleTypeDef *hopamp); |
| void (* MspDeInitCallback) (struct __OPAMP_HandleTypeDef *hopamp); |
| #endif /* USE_HAL_OPAMP_REGISTER_CALLBACKS */ |
| |
| } OPAMP_HandleTypeDef; |
| |
| /** |
| * @brief HAl_OPAMP_TrimmingValueTypeDef definition |
| */ |
| |
| typedef uint32_t HAL_OPAMP_TrimmingValueTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| #if (USE_HAL_OPAMP_REGISTER_CALLBACKS == 1) |
| /** |
| * @brief HAL OPAMP Callback ID enumeration definition |
| */ |
| typedef enum |
| { |
| HAL_OPAMP_MSPINIT_CB_ID = 0x01U, /*!< OPAMP MspInit Callback ID */ |
| HAL_OPAMP_MSPDEINIT_CB_ID = 0x02U, /*!< OPAMP MspDeInit Callback ID */ |
| HAL_OPAMP_ALL_CB_ID = 0x03U /*!< OPAMP All ID */ |
| }HAL_OPAMP_CallbackIDTypeDef; |
| |
| /** |
| * @brief HAL OPAMP Callback pointer definition |
| */ |
| typedef void (*pOPAMP_CallbackTypeDef)(OPAMP_HandleTypeDef *hopamp); |
| #endif /* USE_HAL_OPAMP_REGISTER_CALLBACKS */ |
| |
| |
| /* Exported constants --------------------------------------------------------*/ |
| |
| /** @defgroup OPAMP_Exported_Constants OPAMP Exported Constants |
| * @{ |
| */ |
| |
| /** |
| * OTR register Mask |
| */ |
| #define OPAMP_TRIM_VALUE_MASK OPAMP_OTR_AO1_OPT_OFFSET_TRIM_LOW |
| |
| /** |
| * CSR register Mask |
| */ |
| #define OPAMP_CSR_INSTANCE_OFFSET ( 8U) /* Offset of each OPAMP instance into register CSR */ |
| #define OPAMP_OTR_INSTANCE_OFFSET (10U) /* Offset of each OPAMP instance into register OTR */ |
| |
| |
| /** @defgroup OPAMP_Mode OPAMP Mode |
| * @{ |
| */ |
| #define OPAMP_STANDALONE_MODE 0x00000000U /*!< OPAMP standalone mode */ |
| #define OPAMP_FOLLOWER_MODE 0x00000001U /*!< OPAMP follower mode */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OPAMP_NonInvertingInput OPAMP NonInvertingInput |
| * @{ |
| */ |
| #define OPAMP_NONINVERTINGINPUT_IO0 0x00000000U /*!< Comparator non-inverting input connected to dedicated IO pin low-leakage */ |
| #define OPAMP_NONINVERTINGINPUT_DAC_CH1 0x00000001U /*!< Comparator non-inverting input connected internally to DAC channel 1. Available only on OPAMP1 and OPAMP2. */ |
| #define OPAMP_NONINVERTINGINPUT_DAC_CH2 0x00000002U /*!< Comparator non-inverting input connected internally to DAC channel 2. Available only on OPAMP2 and OPAMP3 (OPAMP3 availability depends on STM32L1 devices). */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OPAMP_InvertingInput OPAMP InvertingInput |
| * @{ |
| */ |
| /* Note: Literal "OPAMP_SEC_INVERTINGINPUT_IO1" is a legacy naming of "OPAMP_INVERTINGINPUT_IO1". It is equivalent and must be replaced by "OPAMP_INVERTINGINPUT_IO1". */ |
| #define OPAMP_INVERTINGINPUT_IO0 0x00000000U /*!< Comparator inverting input connected to dedicated IO pin low-leakage */ |
| #define OPAMP_INVERTINGINPUT_IO1 0x00000001U /*!< Comparator inverting input connected to alternative IO pin available on some device packages */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OPAMP_PowerMode OPAMP PowerMode |
| * @{ |
| */ |
| #define OPAMP_POWERMODE_NORMAL 0x00000000U |
| #define OPAMP_POWERMODE_LOWPOWER 0x00000001U |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OPAMP_PowerSupplyRange OPAMP PowerSupplyRange |
| * @{ |
| */ |
| #define OPAMP_POWERSUPPLY_LOW 0x00000000U /*!< Power supply range low (VDDA lower than 2.4V) */ |
| #define OPAMP_POWERSUPPLY_HIGH OPAMP_CSR_AOP_RANGE /*!< Power supply range high (VDDA higher than 2.4V) */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OPAMP_UserTrimming OPAMP User Trimming |
| * @{ |
| */ |
| #define OPAMP_TRIMMING_FACTORY 0x00000000U /*!< Factory trimming */ |
| #define OPAMP_TRIMMING_USER OPAMP_OTR_OT_USER /*!< User trimming */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup OPAMP_FactoryTrimming OPAMP FactoryTrimming |
| * @{ |
| */ |
| #define OPAMP_FACTORYTRIMMING_DUMMY 0xFFFFFFFFU /*!< Dummy value if trimming value could not be retrieved */ |
| |
| #define OPAMP_FACTORYTRIMMING_P 0U /*!< Offset trimming P */ |
| #define OPAMP_FACTORYTRIMMING_N POSITION_VAL(OPAMP_OTR_AO1_OPT_OFFSET_TRIM_HIGH) /*!< Offset trimming N */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup OPAMP_Private_Constants OPAMP Private Constants |
| * @{ |
| */ |
| |
| /* Offset trimming time: during calibration, minimum time needed between two */ |
| /* steps to have 1 mV accuracy. */ |
| /* Refer to datasheet, electrical characteristics: parameter tOFFTRIM Typ=1ms.*/ |
| /* Unit: ms. */ |
| #define OPAMP_TRIMMING_DELAY ((uint32_t) 1) |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macros -----------------------------------------------------------*/ |
| |
| /** @defgroup OPAMP_Private_Macro OPAMP Private Macro |
| * @{ |
| */ |
| |
| /** @brief Reset OPAMP handle state |
| * @param __HANDLE__ OPAMP handle. |
| * @retval None |
| */ |
| #define __HAL_OPAMP_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_OPAMP_STATE_RESET) |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| |
| /** @defgroup OPAMP_Private_Macro OPAMP Private Macro |
| * @{ |
| */ |
| |
| /** |
| * @brief Select the OPAMP bit OPAxPD (power-down) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_OPAXPD(__HANDLE__) \ |
| (OPAMP_CSR_OPA1PD << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bit S3SELx (switch 3) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_S3SELX(__HANDLE__) \ |
| (OPAMP_CSR_S3SEL1 << ((OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET) & 0x1fU)) |
| |
| /** |
| * @brief Select the OPAMP bit S4SELx (switch 4) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_S4SELX(__HANDLE__) \ |
| (OPAMP_CSR_S4SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bit S5SELx (switch 5) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_S5SELX(__HANDLE__) \ |
| (OPAMP_CSR_S5SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bit S3SELx (switch 6) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_S6SELX(__HANDLE__) \ |
| (OPAMP_CSR_S6SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bit OPAxCAL_L (offset calibration for differential |
| * pair P) corresponding to the selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_OPAXCAL_L(__HANDLE__) \ |
| (OPAMP_CSR_OPA1CAL_L << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bit OPAxCAL_H (offset calibration for differential |
| * pair N) corresponding to the selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_OPAXCAL_H(__HANDLE__) \ |
| (OPAMP_CSR_OPA1CAL_H << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bit OPAxLPM (low power mode) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_OPAXLPM(__HANDLE__) \ |
| (OPAMP_CSR_OPA1LPM << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) |
| |
| /** |
| * @brief Select the OPAMP bits of all switches corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_ALL_SWITCHES(__HANDLE__) \ |
| ( ( ((__HANDLE__)->Instance != OPAMP2) \ |
| )? \ |
| ( \ |
| ((OPAMP_CSR_S3SEL1 | OPAMP_CSR_S4SEL1 | OPAMP_CSR_S5SEL1 | OPAMP_CSR_S6SEL1) << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) \ |
| | \ |
| (OPAMP_CSR_ANAWSEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) \ |
| ) \ |
| : \ |
| ( \ |
| ((OPAMP_CSR_S3SEL1 | OPAMP_CSR_S4SEL1 | OPAMP_CSR_S5SEL1 | OPAMP_CSR_S6SEL1) << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) \ |
| | \ |
| (OPAMP_CSR_ANAWSEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) \ |
| | \ |
| (OPAMP_CSR_S7SEL2) \ |
| ) \ |
| ) |
| |
| /** |
| * @brief Select the OPAMP bit ANAWSELx (switch SanA) corresponding to the |
| * selected OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_ANAWSELX(__HANDLE__) \ |
| (OPAMP_CSR_ANAWSEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) |
| |
| /** |
| * @brief Select the OPAMP bit OPAxCALOUT in function of the selected |
| * OPAMP instance. |
| * @param __HANDLE__: OPAMP handle |
| * @retval None |
| */ |
| #define OPAMP_CSR_OPAXCALOUT(__HANDLE__) \ |
| (OPAMP_CSR_OPA1CALOUT << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) |
| |
| /** |
| * @brief Select the OPAMP trimming bits position value (position of LSB) |
| * in register OPAMP_OTR or register OPAMP_LPOTR in function of the selected |
| * OPAMP instance and the transistors differential pair high (PMOS) or |
| * low (NMOS). |
| * @param __HANDLE__: OPAMP handle |
| * @param __TRIM_HIGH_LOW__: transistors differential pair high or low. |
| * Must be a value of @ref OPAMP_FactoryTrimming. |
| * @retval None |
| */ |
| #define OPAMP_OFFSET_TRIM_BITSPOSITION(__HANDLE__, __TRIM_HIGH_LOW__) \ |
| ((OPAMP_INSTANCE_DECIMAL((__HANDLE__)) * OPAMP_OTR_INSTANCE_OFFSET) + (__TRIM_HIGH_LOW__)) |
| |
| /** |
| * @brief Shift the OPAMP trimming bits to register OPAMP_OTR or register |
| * OPAMP_LPOTR in function of the selected OPAMP instance and the transistors |
| * differential pair high (PMOS) or low (NMOS). |
| * @param __HANDLE__: OPAMP handle |
| * @param __TRIM_HIGH_LOW__: transistors differential pair high or low. |
| * Must be a value of @ref OPAMP_FactoryTrimming. |
| * @param __TRIMMING_VALUE__: Trimming value |
| * @retval None |
| */ |
| #define OPAMP_OFFSET_TRIM_SET(__HANDLE__, __TRIM_HIGH_LOW__, __TRIMMING_VALUE__) \ |
| ((__TRIMMING_VALUE__) << (OPAMP_OFFSET_TRIM_BITSPOSITION((__HANDLE__), (__TRIM_HIGH_LOW__)))) |
| |
| /** |
| * @brief Check that trimming value is within correct range |
| * @param TRIMMINGVALUE: OPAMP trimming value |
| * @retval None |
| */ |
| #define IS_OPAMP_TRIMMINGVALUE(TRIMMINGVALUE) ((TRIMMINGVALUE) <= 30U) |
| |
| #define IS_OPAMP_FUNCTIONAL_NORMALMODE(INPUT) (((INPUT) == OPAMP_STANDALONE_MODE) || \ |
| ((INPUT) == OPAMP_FOLLOWER_MODE)) |
| |
| #define IS_OPAMP_INVERTING_INPUT(INPUT) (((INPUT) == OPAMP_INVERTINGINPUT_IO0) || \ |
| ((INPUT) == OPAMP_INVERTINGINPUT_IO1) ) |
| |
| #define IS_OPAMP_POWERMODE(TRIMMING) (((TRIMMING) == OPAMP_POWERMODE_NORMAL) || \ |
| ((TRIMMING) == OPAMP_POWERMODE_LOWPOWER) ) |
| |
| #define IS_OPAMP_POWER_SUPPLY_RANGE(RANGE) (((RANGE) == OPAMP_POWERSUPPLY_LOW) || \ |
| ((RANGE) == OPAMP_POWERSUPPLY_HIGH) ) |
| |
| #define IS_OPAMP_TRIMMING(TRIMMING) (((TRIMMING) == OPAMP_TRIMMING_FACTORY) || \ |
| ((TRIMMING) == OPAMP_TRIMMING_USER)) |
| |
| #define IS_OPAMP_FACTORYTRIMMING(TRIMMING) (((TRIMMING) == OPAMP_FACTORYTRIMMING_N) || \ |
| ((TRIMMING) == OPAMP_FACTORYTRIMMING_P) ) |
| |
| /** |
| * @} |
| */ |
| |
| |
| /* Include OPAMP HAL Extension module */ |
| #include "stm32l1xx_hal_opamp_ex.h" |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup OPAMP_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup OPAMP_Exported_Functions_Group1 |
| * @{ |
| */ |
| /* Initialization/de-initialization functions **********************************/ |
| HAL_StatusTypeDef HAL_OPAMP_Init(OPAMP_HandleTypeDef *hopamp); |
| HAL_StatusTypeDef HAL_OPAMP_DeInit (OPAMP_HandleTypeDef *hopamp); |
| void HAL_OPAMP_MspInit(OPAMP_HandleTypeDef *hopamp); |
| void HAL_OPAMP_MspDeInit(OPAMP_HandleTypeDef *hopamp); |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup OPAMP_Exported_Functions_Group2 |
| * @{ |
| */ |
| |
| /* I/O operation functions *****************************************************/ |
| HAL_StatusTypeDef HAL_OPAMP_Start(OPAMP_HandleTypeDef *hopamp); |
| HAL_StatusTypeDef HAL_OPAMP_Stop(OPAMP_HandleTypeDef *hopamp); |
| HAL_StatusTypeDef HAL_OPAMP_SelfCalibrate(OPAMP_HandleTypeDef *hopamp); |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup OPAMP_Exported_Functions_Group3 |
| * @{ |
| */ |
| |
| /* Peripheral Control functions ************************************************/ |
| #if (USE_HAL_OPAMP_REGISTER_CALLBACKS == 1) |
| /* OPAMP callback registering/unregistering */ |
| HAL_StatusTypeDef HAL_OPAMP_RegisterCallback (OPAMP_HandleTypeDef *hopamp, HAL_OPAMP_CallbackIDTypeDef CallbackID, pOPAMP_CallbackTypeDef pCallback); |
| HAL_StatusTypeDef HAL_OPAMP_UnRegisterCallback (OPAMP_HandleTypeDef *hopamp, HAL_OPAMP_CallbackIDTypeDef CallbackID); |
| #endif /* USE_HAL_OPAMP_REGISTER_CALLBACKS */ |
| |
| HAL_StatusTypeDef HAL_OPAMP_Lock(OPAMP_HandleTypeDef *hopamp); |
| HAL_OPAMP_TrimmingValueTypeDef HAL_OPAMP_GetTrimOffset (OPAMP_HandleTypeDef *hopamp, uint32_t trimmingoffset); |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup OPAMP_Exported_Functions_Group4 |
| * @{ |
| */ |
| |
| /* Peripheral State functions **************************************************/ |
| HAL_OPAMP_StateTypeDef HAL_OPAMP_GetState(OPAMP_HandleTypeDef *hopamp); |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* STM32L151xCA || STM32L151xD || STM32L152xCA || STM32L152xD || STM32L162xCA || STM32L162xD || STM32L151xE || STM32L151xDX || STM32L152xE || STM32L152xDX || STM32L162xE || STM32L162xDX || STM32L162xC || STM32L152xC || STM32L151xC */ |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* STM32L1xx_HAL_OPAMP_H */ |
| |
