| /** |
| ****************************************************************************** |
| * @file stm32l5xx_ll_spi.c |
| * @author MCD Application Team |
| * @brief SPI LL module driver. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2019 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| #if defined(USE_FULL_LL_DRIVER) |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32l5xx_ll_spi.h" |
| #include "stm32l5xx_ll_bus.h" |
| |
| #ifdef USE_FULL_ASSERT |
| #include "stm32_assert.h" |
| #else |
| #define assert_param(expr) ((void)0U) |
| #endif |
| |
| /** @addtogroup STM32L5xx_LL_Driver |
| * @{ |
| */ |
| |
| #if defined (SPI1) || defined (SPI2) || defined (SPI3) |
| |
| /** @addtogroup SPI_LL |
| * @{ |
| */ |
| |
| /* Private types -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup SPI_LL_Private_Constants SPI Private Constants |
| * @{ |
| */ |
| /* SPI registers Masks */ |
| #define SPI_CR1_CLEAR_MASK (SPI_CR1_CPHA | SPI_CR1_CPOL | SPI_CR1_MSTR | \ |
| SPI_CR1_BR | SPI_CR1_LSBFIRST | SPI_CR1_SSI | \ |
| SPI_CR1_SSM | SPI_CR1_RXONLY | SPI_CR1_CRCL | \ |
| SPI_CR1_CRCNEXT | SPI_CR1_CRCEN | SPI_CR1_BIDIOE | \ |
| SPI_CR1_BIDIMODE) |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup SPI_LL_Private_Macros SPI Private Macros |
| * @{ |
| */ |
| #define IS_LL_SPI_TRANSFER_DIRECTION(__VALUE__) (((__VALUE__) == LL_SPI_FULL_DUPLEX) \ |
| || ((__VALUE__) == LL_SPI_SIMPLEX_RX) \ |
| || ((__VALUE__) == LL_SPI_HALF_DUPLEX_RX) \ |
| || ((__VALUE__) == LL_SPI_HALF_DUPLEX_TX)) |
| |
| #define IS_LL_SPI_MODE(__VALUE__) (((__VALUE__) == LL_SPI_MODE_MASTER) \ |
| || ((__VALUE__) == LL_SPI_MODE_SLAVE)) |
| |
| #define IS_LL_SPI_DATAWIDTH(__VALUE__) (((__VALUE__) == LL_SPI_DATAWIDTH_4BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_5BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_6BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_7BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_8BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_9BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_10BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_11BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_12BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_13BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_14BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_15BIT) \ |
| || ((__VALUE__) == LL_SPI_DATAWIDTH_16BIT)) |
| |
| #define IS_LL_SPI_POLARITY(__VALUE__) (((__VALUE__) == LL_SPI_POLARITY_LOW) \ |
| || ((__VALUE__) == LL_SPI_POLARITY_HIGH)) |
| |
| #define IS_LL_SPI_PHASE(__VALUE__) (((__VALUE__) == LL_SPI_PHASE_1EDGE) \ |
| || ((__VALUE__) == LL_SPI_PHASE_2EDGE)) |
| |
| #define IS_LL_SPI_NSS(__VALUE__) (((__VALUE__) == LL_SPI_NSS_SOFT) \ |
| || ((__VALUE__) == LL_SPI_NSS_HARD_INPUT) \ |
| || ((__VALUE__) == LL_SPI_NSS_HARD_OUTPUT)) |
| |
| #define IS_LL_SPI_BAUDRATE(__VALUE__) (((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV2) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV4) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV8) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV16) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV32) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV64) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV128) \ |
| || ((__VALUE__) == LL_SPI_BAUDRATEPRESCALER_DIV256)) |
| |
| #define IS_LL_SPI_BITORDER(__VALUE__) (((__VALUE__) == LL_SPI_LSB_FIRST) \ |
| || ((__VALUE__) == LL_SPI_MSB_FIRST)) |
| |
| #define IS_LL_SPI_CRCCALCULATION(__VALUE__) (((__VALUE__) == LL_SPI_CRCCALCULATION_ENABLE) \ |
| || ((__VALUE__) == LL_SPI_CRCCALCULATION_DISABLE)) |
| |
| #define IS_LL_SPI_CRC_POLYNOMIAL(__VALUE__) ((__VALUE__) >= 0x1U) |
| |
| /** |
| * @} |
| */ |
| |
| /* Private function prototypes -----------------------------------------------*/ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup SPI_LL_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup SPI_LL_EF_Init |
| * @{ |
| */ |
| |
| /** |
| * @brief De-initialize the SPI registers to their default reset values. |
| * @param SPIx SPI Instance |
| * @retval An ErrorStatus enumeration value: |
| * - SUCCESS: SPI registers are de-initialized |
| * - ERROR: SPI registers are not de-initialized |
| */ |
| ErrorStatus LL_SPI_DeInit(SPI_TypeDef *SPIx) |
| { |
| ErrorStatus status = ERROR; |
| |
| /* Check the parameters */ |
| assert_param(IS_SPI_ALL_INSTANCE(SPIx)); |
| |
| #if defined(SPI1) |
| if (SPIx == SPI1) |
| { |
| /* Force reset of SPI clock */ |
| LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_SPI1); |
| |
| /* Release reset of SPI clock */ |
| LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_SPI1); |
| |
| status = SUCCESS; |
| } |
| #endif /* SPI1 */ |
| #if defined(SPI2) |
| if (SPIx == SPI2) |
| { |
| /* Force reset of SPI clock */ |
| LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_SPI2); |
| |
| /* Release reset of SPI clock */ |
| LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_SPI2); |
| |
| status = SUCCESS; |
| } |
| #endif /* SPI2 */ |
| #if defined(SPI3) |
| if (SPIx == SPI3) |
| { |
| /* Force reset of SPI clock */ |
| LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_SPI3); |
| |
| /* Release reset of SPI clock */ |
| LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_SPI3); |
| |
| status = SUCCESS; |
| } |
| #endif /* SPI3 */ |
| |
| return status; |
| } |
| |
| /** |
| * @brief Initialize the SPI registers according to the specified parameters in SPI_InitStruct. |
| * @note As some bits in SPI configuration registers can only be written when the SPI is disabled (SPI_CR1_SPE bit =0), |
| * SPI peripheral should be in disabled state prior calling this function. Otherwise, ERROR result will be returned. |
| * @param SPIx SPI Instance |
| * @param SPI_InitStruct pointer to a @ref LL_SPI_InitTypeDef structure |
| * @retval An ErrorStatus enumeration value. (Return always SUCCESS) |
| */ |
| ErrorStatus LL_SPI_Init(SPI_TypeDef *SPIx, LL_SPI_InitTypeDef *SPI_InitStruct) |
| { |
| ErrorStatus status = ERROR; |
| |
| /* Check the SPI Instance SPIx*/ |
| assert_param(IS_SPI_ALL_INSTANCE(SPIx)); |
| |
| /* Check the SPI parameters from SPI_InitStruct*/ |
| assert_param(IS_LL_SPI_TRANSFER_DIRECTION(SPI_InitStruct->TransferDirection)); |
| assert_param(IS_LL_SPI_MODE(SPI_InitStruct->Mode)); |
| assert_param(IS_LL_SPI_DATAWIDTH(SPI_InitStruct->DataWidth)); |
| assert_param(IS_LL_SPI_POLARITY(SPI_InitStruct->ClockPolarity)); |
| assert_param(IS_LL_SPI_PHASE(SPI_InitStruct->ClockPhase)); |
| assert_param(IS_LL_SPI_NSS(SPI_InitStruct->NSS)); |
| assert_param(IS_LL_SPI_BAUDRATE(SPI_InitStruct->BaudRate)); |
| assert_param(IS_LL_SPI_BITORDER(SPI_InitStruct->BitOrder)); |
| assert_param(IS_LL_SPI_CRCCALCULATION(SPI_InitStruct->CRCCalculation)); |
| |
| if (LL_SPI_IsEnabled(SPIx) == 0x00000000U) |
| { |
| /*---------------------------- SPIx CR1 Configuration ------------------------ |
| * Configure SPIx CR1 with parameters: |
| * - TransferDirection: SPI_CR1_BIDIMODE, SPI_CR1_BIDIOE and SPI_CR1_RXONLY bits |
| * - Master/Slave Mode: SPI_CR1_MSTR bit |
| * - ClockPolarity: SPI_CR1_CPOL bit |
| * - ClockPhase: SPI_CR1_CPHA bit |
| * - NSS management: SPI_CR1_SSM bit |
| * - BaudRate prescaler: SPI_CR1_BR[2:0] bits |
| * - BitOrder: SPI_CR1_LSBFIRST bit |
| * - CRCCalculation: SPI_CR1_CRCEN bit |
| */ |
| MODIFY_REG(SPIx->CR1, |
| SPI_CR1_CLEAR_MASK, |
| SPI_InitStruct->TransferDirection | SPI_InitStruct->Mode | |
| SPI_InitStruct->ClockPolarity | SPI_InitStruct->ClockPhase | |
| SPI_InitStruct->NSS | SPI_InitStruct->BaudRate | |
| SPI_InitStruct->BitOrder | SPI_InitStruct->CRCCalculation); |
| |
| /*---------------------------- SPIx CR2 Configuration ------------------------ |
| * Configure SPIx CR2 with parameters: |
| * - DataWidth: DS[3:0] bits |
| * - NSS management: SSOE bit |
| */ |
| MODIFY_REG(SPIx->CR2, |
| SPI_CR2_DS | SPI_CR2_SSOE, |
| SPI_InitStruct->DataWidth | (SPI_InitStruct->NSS >> 16U)); |
| |
| /*---------------------------- SPIx CRCPR Configuration ---------------------- |
| * Configure SPIx CRCPR with parameters: |
| * - CRCPoly: CRCPOLY[15:0] bits |
| */ |
| if (SPI_InitStruct->CRCCalculation == LL_SPI_CRCCALCULATION_ENABLE) |
| { |
| assert_param(IS_LL_SPI_CRC_POLYNOMIAL(SPI_InitStruct->CRCPoly)); |
| LL_SPI_SetCRCPolynomial(SPIx, SPI_InitStruct->CRCPoly); |
| } |
| status = SUCCESS; |
| } |
| |
| return status; |
| } |
| |
| /** |
| * @brief Set each @ref LL_SPI_InitTypeDef field to default value. |
| * @param SPI_InitStruct pointer to a @ref LL_SPI_InitTypeDef structure |
| * whose fields will be set to default values. |
| * @retval None |
| */ |
| void LL_SPI_StructInit(LL_SPI_InitTypeDef *SPI_InitStruct) |
| { |
| /* Set SPI_InitStruct fields to default values */ |
| SPI_InitStruct->TransferDirection = LL_SPI_FULL_DUPLEX; |
| SPI_InitStruct->Mode = LL_SPI_MODE_SLAVE; |
| SPI_InitStruct->DataWidth = LL_SPI_DATAWIDTH_8BIT; |
| SPI_InitStruct->ClockPolarity = LL_SPI_POLARITY_LOW; |
| SPI_InitStruct->ClockPhase = LL_SPI_PHASE_1EDGE; |
| SPI_InitStruct->NSS = LL_SPI_NSS_HARD_INPUT; |
| SPI_InitStruct->BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV2; |
| SPI_InitStruct->BitOrder = LL_SPI_MSB_FIRST; |
| SPI_InitStruct->CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE; |
| SPI_InitStruct->CRCPoly = 7U; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* defined (SPI1) || defined (SPI2) || defined (SPI3) */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* USE_FULL_LL_DRIVER */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
