/**
  ******************************************************************************
  * @file    stm32wbxx_ll_comp.h
  * @author  MCD Application Team
  * @brief   Header file of COMP LL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32WBxx_LL_COMP_H
#define STM32WBxx_LL_COMP_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32wbxx.h"

/** @addtogroup STM32WBxx_LL_Driver
  * @{
  */


/** @defgroup COMP_LL COMP
  * @{
  */

/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/** @defgroup COMP_LL_Private_Constants COMP Private Constants
  * @{
  */

/* COMP registers bits positions */
#define LL_COMP_OUTPUT_LEVEL_BITOFFSET_POS (30UL) /* Value equivalent to POSITION_VAL(COMP_CSR_VALUE) */

/**
  * @}
  */

/* Private macros ------------------------------------------------------------*/
/* Exported types ------------------------------------------------------------*/
#if defined(USE_FULL_LL_DRIVER)
/** @defgroup COMP_LL_ES_INIT COMP Exported Init structure
  * @{
  */

/**
  * @brief  Structure definition of some features of COMP instance.
  */
typedef struct
{
  uint32_t PowerMode;                   /*!< Set comparator operating mode to adjust power and speed.
                                             This parameter can be a value of @ref COMP_LL_EC_POWERMODE

                                             This feature can be modified afterwards using unitary function @ref LL_COMP_SetPowerMode(). */

  uint32_t InputPlus;                   /*!< Set comparator input plus (non-inverting input).
                                             This parameter can be a value of @ref COMP_LL_EC_INPUT_PLUS

                                             This feature can be modified afterwards using unitary function @ref LL_COMP_SetInputPlus(). */

  uint32_t InputMinus;                  /*!< Set comparator input minus (inverting input).
                                             This parameter can be a value of @ref COMP_LL_EC_INPUT_MINUS

                                             This feature can be modified afterwards using unitary function @ref LL_COMP_SetInputMinus(). */

  uint32_t InputHysteresis;             /*!< Set comparator hysteresis mode of the input minus.
                                             This parameter can be a value of @ref COMP_LL_EC_INPUT_HYSTERESIS

                                             This feature can be modified afterwards using unitary function @ref LL_COMP_SetInputHysteresis(). */

  uint32_t OutputPolarity;              /*!< Set comparator output polarity.
                                             This parameter can be a value of @ref COMP_LL_EC_OUTPUT_POLARITY

                                             This feature can be modified afterwards using unitary function @ref LL_COMP_SetOutputPolarity(). */

  uint32_t OutputBlankingSource;        /*!< Set comparator blanking source.
                                             This parameter can be a value of @ref COMP_LL_EC_OUTPUT_BLANKING_SOURCE

                                             This feature can be modified afterwards using unitary function @ref LL_COMP_SetOutputBlankingSource(). */

} LL_COMP_InitTypeDef;

/**
  * @}
  */
#endif /* USE_FULL_LL_DRIVER */

/* Exported constants --------------------------------------------------------*/
/** @defgroup COMP_LL_Exported_Constants COMP Exported Constants
  * @{
  */

/** @defgroup COMP_LL_EC_COMMON_WINDOWMODE Comparator common modes - Window mode
  * @{
  */
#define LL_COMP_WINDOWMODE_DISABLE                 (0x00000000UL)          /*!< Window mode disable: Comparators 1 and 2 are independent */
#define LL_COMP_WINDOWMODE_COMP1_INPUT_PLUS_COMMON (COMP_CSR_WINMODE)      /*!< Window mode enable: Comparators instances pair COMP1 and COMP2 have their input plus connected together. The common input is COMP1 input plus (COMP2 input plus is no more accessible). */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_POWERMODE Comparator modes - Power mode
  * @{
  */
#define LL_COMP_POWERMODE_HIGHSPEED     (0x00000000UL)                            /*!< COMP power mode to high speed */
#define LL_COMP_POWERMODE_MEDIUMSPEED   (COMP_CSR_PWRMODE_0)                      /*!< COMP power mode to medium speed */
#define LL_COMP_POWERMODE_ULTRALOWPOWER (COMP_CSR_PWRMODE_1 | COMP_CSR_PWRMODE_0) /*!< COMP power mode to ultra-low power */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_INPUT_PLUS Comparator inputs - Input plus (input non-inverting) selection
  * @{
  */
#define LL_COMP_INPUT_PLUS_IO1          (0x00000000UL)                          /*!< Comparator input plus connected to IO1 (pin PC5 for COMP1, pin PB4 for COMP2) */
#define LL_COMP_INPUT_PLUS_IO2          (COMP_CSR_INPSEL_0)                     /*!< Comparator input plus connected to IO2 (pin PB2 for COMP1, pin PB6 for COMP2) */
#define LL_COMP_INPUT_PLUS_IO3          (COMP_CSR_INPSEL_1)                     /*!< Comparator input plus connected to IO3 (pin PA1 for COMP1, pin PA3 for COMP2) */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_INPUT_MINUS Comparator inputs - Input minus (input inverting) selection
  * @{
  */
#define LL_COMP_INPUT_MINUS_1_4VREFINT  (                                                            COMP_CSR_SCALEN | COMP_CSR_BRGEN)        /*!< Comparator input minus connected to 1/4 VrefInt  */
#define LL_COMP_INPUT_MINUS_1_2VREFINT  (                                        COMP_CSR_INMSEL_0 | COMP_CSR_SCALEN | COMP_CSR_BRGEN)        /*!< Comparator input minus connected to 1/2 VrefInt  */
#define LL_COMP_INPUT_MINUS_3_4VREFINT  (                    COMP_CSR_INMSEL_1                     | COMP_CSR_SCALEN | COMP_CSR_BRGEN)        /*!< Comparator input minus connected to 3/4 VrefInt  */
#define LL_COMP_INPUT_MINUS_VREFINT     (                    COMP_CSR_INMSEL_1 | COMP_CSR_INMSEL_0 | COMP_CSR_SCALEN                 )        /*!< Comparator input minus connected to VrefInt */
#define LL_COMP_INPUT_MINUS_IO1         (COMP_CSR_INMSEL_2 | COMP_CSR_INMSEL_1                    )                                           /*!< Comparator input minus connected to IO1 (pin PA9 for COMP1, pin PB3 for COMP2) */
#define LL_COMP_INPUT_MINUS_IO2         (COMP_CSR_INMSEL_2 | COMP_CSR_INMSEL_1 | COMP_CSR_INMSEL_0)                                           /*!< Comparator input minus connected to IO2 (pin PC4 for COMP1, pin PB7 for COMP2) */
#define LL_COMP_INPUT_MINUS_IO3         (                     COMP_CSR_INMESEL_0 | COMP_CSR_INMSEL_2 | COMP_CSR_INMSEL_1 | COMP_CSR_INMSEL_0) /*!< Comparator input minus connected to IO3 (pin PA0 for COMP1, pin PA2 for COMP2) */
#define LL_COMP_INPUT_MINUS_IO4         (COMP_CSR_INMESEL_1                      | COMP_CSR_INMSEL_2 | COMP_CSR_INMSEL_1 | COMP_CSR_INMSEL_0) /*!< Comparator input minus connected to IO4 (pin PA4 for COMP1, pin PA4 for COMP2) */
#define LL_COMP_INPUT_MINUS_IO5         (COMP_CSR_INMESEL_1 | COMP_CSR_INMESEL_0 | COMP_CSR_INMSEL_2 | COMP_CSR_INMSEL_1 | COMP_CSR_INMSEL_0) /*!< Comparator input minus connected to IO5 (pin PA5 for COMP1, pin PA5 for COMP2) */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_INPUT_HYSTERESIS Comparator input - Hysteresis
  * @{
  */
#define LL_COMP_HYSTERESIS_NONE         (0x00000000UL)                      /*!< No hysteresis */
#define LL_COMP_HYSTERESIS_LOW          (                  COMP_CSR_HYST_0) /*!< Hysteresis level low */
#define LL_COMP_HYSTERESIS_MEDIUM       (COMP_CSR_HYST_1                  ) /*!< Hysteresis level medium */
#define LL_COMP_HYSTERESIS_HIGH         (COMP_CSR_HYST_1 | COMP_CSR_HYST_0) /*!< Hysteresis level high */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_OUTPUT_POLARITY Comparator output - Output polarity
  * @{
  */
#define LL_COMP_OUTPUTPOL_NONINVERTED   (0x00000000UL)          /*!< COMP output polarity is not inverted: comparator output is high when the plus (non-inverting) input is at a higher voltage than the minus (inverting) input */
#define LL_COMP_OUTPUTPOL_INVERTED      (COMP_CSR_POLARITY)     /*!< COMP output polarity is inverted: comparator output is low when the plus (non-inverting) input is at a lower voltage than the minus (inverting) input */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_OUTPUT_BLANKING_SOURCE Comparator output - Blanking source
  * @{
  */
#define LL_COMP_BLANKINGSRC_NONE            (0x00000000UL)          /*!<Comparator output without blanking */
/* Note: Output blanking source common to all COMP instances */
#define LL_COMP_BLANKINGSRC_TIM1_OC5        (COMP_CSR_BLANKING_0)   /*!< Comparator output blanking source TIM1 OC5 (common to all COMP instances: COMP1, COMP2) */
#define LL_COMP_BLANKINGSRC_TIM2_OC3        (COMP_CSR_BLANKING_1)   /*!< Comparator output blanking source TIM2 OC3 (common to all COMP instances: COMP1, COMP2) */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_OUTPUT_LEVEL Comparator output - Output level
  * @{
  */
#define LL_COMP_OUTPUT_LEVEL_LOW        (0x00000000UL)          /*!< Comparator output level low (if the polarity is not inverted, otherwise to be complemented) */
#define LL_COMP_OUTPUT_LEVEL_HIGH       (0x00000001UL)          /*!< Comparator output level high (if the polarity is not inverted, otherwise to be complemented) */
/**
  * @}
  */

/** @defgroup COMP_LL_EC_HW_DELAYS  Definitions of COMP hardware constraints delays
  * @note   Only COMP peripheral HW delays are defined in COMP LL driver driver,
  *         not timeout values.
  *         For details on delays values, refer to descriptions in source code
  *         above each literal definition.
  * @{
  */

/* Delay for comparator startup time.                                         */
/* Note: Delay required to reach propagation delay specification.             */
/* Literal set to maximum value (refer to device datasheet,                   */
/* parameter "tSTART").                                                       */
/* Unit: us                                                                   */
#define LL_COMP_DELAY_STARTUP_US          ( 80UL) /*!< Delay for COMP startup time */

/* Delay for comparator voltage scaler stabilization time.                    */
/* Note: Voltage scaler is used when selecting comparator input               */
/*       based on VrefInt: VrefInt or subdivision of VrefInt.                 */
/* Literal set to maximum value (refer to device datasheet,                   */
/* parameter "tSTART_SCALER").                                                */
/* Unit: us                                                                   */
#define LL_COMP_DELAY_VOLTAGE_SCALER_STAB_US ( 200UL) /*!< Delay for COMP voltage scaler stabilization time */

/**
  * @}
  */

/**
  * @}
  */

/* Exported macro ------------------------------------------------------------*/
/** @defgroup COMP_LL_Exported_Macros COMP Exported Macros
  * @{
  */
/** @defgroup COMP_LL_EM_WRITE_READ Common write and read registers macro
  * @{
  */

/**
  * @brief  Write a value in COMP register
  * @param  __INSTANCE__ comparator instance
  * @param  __REG__ Register to be written
  * @param  __VALUE__ Value to be written in the register
  * @retval None
  */
#define LL_COMP_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG((__INSTANCE__)->__REG__, (__VALUE__))

/**
  * @brief  Read a value in COMP register
  * @param  __INSTANCE__ comparator instance
  * @param  __REG__ Register to be read
  * @retval Register value
  */
#define LL_COMP_ReadReg(__INSTANCE__, __REG__) READ_REG((__INSTANCE__)->__REG__)
/**
  * @}
  */

/** @defgroup COMP_LL_EM_HELPER_MACRO COMP helper macro
  * @{
  */

/**
  * @brief  Helper macro to select the COMP common instance
  *         to which is belonging the selected COMP instance.
  * @note   COMP common register instance can be used to
  *         set parameters common to several COMP instances.
  *         Refer to functions having argument "COMPxy_COMMON" as parameter.
  * @param  __COMPx__ COMP instance
  * @retval COMP common instance or value "0" if there is no COMP common instance.
  */
#define __LL_COMP_COMMON_INSTANCE(__COMPx__)                                   \
  (COMP12_COMMON)

/**
  * @}
  */

/**
  * @}
  */

/* Exported functions --------------------------------------------------------*/
/** @defgroup COMP_LL_Exported_Functions COMP Exported Functions
  * @{
  */

/** @defgroup COMP_LL_EF_Configuration_comparator_common Configuration of COMP hierarchical scope: common to several COMP instances
  * @{
  */

/**
  * @brief  Set window mode of a pair of comparators instances
  *         (2 consecutive COMP instances odd and even COMP<x> and COMP<x+1>).
  * @rmtoll CSR      WINMODE        LL_COMP_SetCommonWindowMode
  * @param  COMPxy_COMMON Comparator common instance
  *         (can be set directly from CMSIS definition or by using helper macro @ref __LL_COMP_COMMON_INSTANCE() )
  * @param  WindowMode This parameter can be one of the following values:
  *         @arg @ref LL_COMP_WINDOWMODE_DISABLE
  *         @arg @ref LL_COMP_WINDOWMODE_COMP1_INPUT_PLUS_COMMON
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetCommonWindowMode(COMP_Common_TypeDef *COMPxy_COMMON, uint32_t WindowMode)
{
  /* Note: On this STM32 serie, window mode can be set only                   */
  /*       from COMP instance: COMP2.                                         */
  MODIFY_REG(COMPxy_COMMON->CSR, COMP_CSR_WINMODE, WindowMode);
}

/**
  * @brief  Get window mode of a pair of comparators instances
  *         (2 consecutive COMP instances odd and even COMP<x> and COMP<x+1>).
  * @rmtoll CSR      WINMODE        LL_COMP_GetCommonWindowMode
  * @param  COMPxy_COMMON Comparator common instance
  *         (can be set directly from CMSIS definition or by using helper macro @ref __LL_COMP_COMMON_INSTANCE() )
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_WINDOWMODE_DISABLE
  *         @arg @ref LL_COMP_WINDOWMODE_COMP1_INPUT_PLUS_COMMON
  */
__STATIC_INLINE uint32_t LL_COMP_GetCommonWindowMode(COMP_Common_TypeDef *COMPxy_COMMON)
{
  return (uint32_t)(READ_BIT(COMPxy_COMMON->CSR, COMP_CSR_WINMODE));
}

/**
  * @}
  */

/** @defgroup COMP_LL_EF_Configuration_comparator_modes Configuration of comparator modes
  * @{
  */

/**
  * @brief  Set comparator instance operating mode to adjust power and speed.
  * @rmtoll CSR      PWRMODE        LL_COMP_SetPowerMode
  * @param  COMPx Comparator instance
  * @param  PowerMode This parameter can be one of the following values:
  *         @arg @ref LL_COMP_POWERMODE_HIGHSPEED
  *         @arg @ref LL_COMP_POWERMODE_MEDIUMSPEED
  *         @arg @ref LL_COMP_POWERMODE_ULTRALOWPOWER
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetPowerMode(COMP_TypeDef *COMPx, uint32_t PowerMode)
{
  MODIFY_REG(COMPx->CSR, COMP_CSR_PWRMODE, PowerMode);
}

/**
  * @brief  Get comparator instance operating mode to adjust power and speed.
  * @rmtoll CSR      PWRMODE        LL_COMP_GetPowerMode
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_POWERMODE_HIGHSPEED
  *         @arg @ref LL_COMP_POWERMODE_MEDIUMSPEED
  *         @arg @ref LL_COMP_POWERMODE_ULTRALOWPOWER
  */
__STATIC_INLINE uint32_t LL_COMP_GetPowerMode(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_PWRMODE));
}

/**
  * @}
  */

/** @defgroup COMP_LL_EF_Configuration_comparator_inputs Configuration of comparator inputs
  * @{
  */

/**
  * @brief  Set comparator inputs minus (inverting) and plus (non-inverting).
  * @note   In case of comparator input selected to be connected to IO:
  *         GPIO pins are specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @note   On this STM32 serie, scaler bridge is configurable:
  *         to optimize power consumption, this function enables the
  *         voltage scaler bridge only when required
  *         (when selecting comparator input based on VrefInt: VrefInt or
  *         subdivision of VrefInt).
  *         - For scaler bridge power consumption values,
  *           refer to device datasheet, parameter "IDDA(SCALER)".
  *         - Voltage scaler requires a delay for voltage stabilization.
  *           Refer to device datasheet, parameter "tSTART_SCALER".
  *         - Scaler bridge is common for all comparator instances,
  *           therefore if at least one of the comparator instance
  *           is requiring the scaler bridge, it remains enabled.
  * @rmtoll CSR      INMSEL         LL_COMP_ConfigInputs\n
  *         CSR      INPSEL         LL_COMP_ConfigInputs\n
  *         CSR      BRGEN          LL_COMP_ConfigInputs\n
  *         CSR      SCALEN         LL_COMP_ConfigInputs
  * @param  COMPx Comparator instance
  * @param  InputMinus This parameter can be one of the following values:
  *         @arg @ref LL_COMP_INPUT_MINUS_1_4VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_1_2VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_3_4VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_IO1
  *         @arg @ref LL_COMP_INPUT_MINUS_IO2
  *         @arg @ref LL_COMP_INPUT_MINUS_IO3
  *         @arg @ref LL_COMP_INPUT_MINUS_IO4
  *         @arg @ref LL_COMP_INPUT_MINUS_IO5
  * @param  InputPlus This parameter can be one of the following values:
  *         @arg @ref LL_COMP_INPUT_PLUS_IO1
  *         @arg @ref LL_COMP_INPUT_PLUS_IO2
  *         @arg @ref LL_COMP_INPUT_PLUS_IO3 (*)
  *
  *         (*) Parameter not available on all devices.
  * @retval None
  */
__STATIC_INLINE void LL_COMP_ConfigInputs(COMP_TypeDef *COMPx, uint32_t InputMinus, uint32_t InputPlus)
{
  MODIFY_REG(COMPx->CSR,
             COMP_CSR_INMESEL | COMP_CSR_INMSEL | COMP_CSR_INPSEL | COMP_CSR_SCALEN | COMP_CSR_BRGEN,
             InputMinus | InputPlus);
}

/**
  * @brief  Set comparator input plus (non-inverting).
  * @note   In case of comparator input selected to be connected to IO:
  *         GPIO pins are specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @rmtoll CSR      INPSEL         LL_COMP_SetInputPlus
  * @param  COMPx Comparator instance
  * @param  InputPlus This parameter can be one of the following values:
  *         @arg @ref LL_COMP_INPUT_PLUS_IO1
  *         @arg @ref LL_COMP_INPUT_PLUS_IO2
  *         @arg @ref LL_COMP_INPUT_PLUS_IO3 (*)
  *
  *         (*) Parameter not available on all devices.
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetInputPlus(COMP_TypeDef *COMPx, uint32_t InputPlus)
{
  MODIFY_REG(COMPx->CSR, COMP_CSR_INPSEL, InputPlus);
}

/**
  * @brief  Get comparator input plus (non-inverting).
  * @note   In case of comparator input selected to be connected to IO:
  *         GPIO pins are specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @rmtoll CSR      INPSEL         LL_COMP_GetInputPlus
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_INPUT_PLUS_IO1
  *         @arg @ref LL_COMP_INPUT_PLUS_IO2
  *         @arg @ref LL_COMP_INPUT_PLUS_IO3 (*)
  *
  *         (*) Parameter not available on all devices.
  */
__STATIC_INLINE uint32_t LL_COMP_GetInputPlus(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_INPSEL));
}

/**
  * @brief  Set comparator input minus (inverting).
  * @note   In case of comparator input selected to be connected to IO:
  *         GPIO pins are specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @note   On this STM32 serie, scaler bridge is configurable:
  *         to optimize power consumption, this function enables the
  *         voltage scaler bridge only when required
  *         (when selecting comparator input based on VrefInt: VrefInt or
  *         subdivision of VrefInt).
  *         - For scaler bridge power consumption values,
  *           refer to device datasheet, parameter "IDDA(SCALER)".
  *         - Voltage scaler requires a delay for voltage stabilization.
  *           Refer to device datasheet, parameter "tSTART_SCALER".
  *         - Scaler bridge is common for all comparator instances,
  *           therefore if at least one of the comparator instance
  *           is requiring the scaler bridge, it remains enabled.
  * @rmtoll CSR      INMSEL         LL_COMP_SetInputMinus\n
  *         CSR      BRGEN          LL_COMP_SetInputMinus\n
  *         CSR      SCALEN         LL_COMP_SetInputMinus
  * @param  COMPx Comparator instance
  * @param  InputMinus This parameter can be one of the following values:
  *         @arg @ref LL_COMP_INPUT_MINUS_1_4VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_1_2VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_3_4VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_IO1
  *         @arg @ref LL_COMP_INPUT_MINUS_IO2
  *         @arg @ref LL_COMP_INPUT_MINUS_IO3
  *         @arg @ref LL_COMP_INPUT_MINUS_IO4
  *         @arg @ref LL_COMP_INPUT_MINUS_IO5
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetInputMinus(COMP_TypeDef *COMPx, uint32_t InputMinus)
{
  MODIFY_REG(COMPx->CSR, COMP_CSR_INMESEL | COMP_CSR_INMSEL | COMP_CSR_SCALEN | COMP_CSR_BRGEN, InputMinus);
}

/**
  * @brief  Get comparator input minus (inverting).
  * @note   In case of comparator input selected to be connected to IO:
  *         GPIO pins are specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @rmtoll CSR      INMSEL         LL_COMP_GetInputMinus\n
  *         CSR      BRGEN          LL_COMP_GetInputMinus\n
  *         CSR      SCALEN         LL_COMP_GetInputMinus
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_INPUT_MINUS_1_4VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_1_2VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_3_4VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_VREFINT
  *         @arg @ref LL_COMP_INPUT_MINUS_IO1
  *         @arg @ref LL_COMP_INPUT_MINUS_IO2
  *         @arg @ref LL_COMP_INPUT_MINUS_IO3
  *         @arg @ref LL_COMP_INPUT_MINUS_IO4
  *         @arg @ref LL_COMP_INPUT_MINUS_IO5
  */
__STATIC_INLINE uint32_t LL_COMP_GetInputMinus(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_INMESEL | COMP_CSR_INMSEL | COMP_CSR_SCALEN | COMP_CSR_BRGEN));
}

/**
  * @brief  Set comparator instance hysteresis mode of the input minus (inverting input).
  * @rmtoll CSR      HYST           LL_COMP_SetInputHysteresis
  * @param  COMPx Comparator instance
  * @param  InputHysteresis This parameter can be one of the following values:
  *         @arg @ref LL_COMP_HYSTERESIS_NONE
  *         @arg @ref LL_COMP_HYSTERESIS_LOW
  *         @arg @ref LL_COMP_HYSTERESIS_MEDIUM
  *         @arg @ref LL_COMP_HYSTERESIS_HIGH
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetInputHysteresis(COMP_TypeDef *COMPx, uint32_t InputHysteresis)
{
  MODIFY_REG(COMPx->CSR, COMP_CSR_HYST, InputHysteresis);
}

/**
  * @brief  Get comparator instance hysteresis mode of the minus (inverting) input.
  * @rmtoll CSR      HYST           LL_COMP_GetInputHysteresis
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_HYSTERESIS_NONE
  *         @arg @ref LL_COMP_HYSTERESIS_LOW
  *         @arg @ref LL_COMP_HYSTERESIS_MEDIUM
  *         @arg @ref LL_COMP_HYSTERESIS_HIGH
  */
__STATIC_INLINE uint32_t LL_COMP_GetInputHysteresis(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_HYST));
}

/**
  * @}
  */

/** @defgroup COMP_LL_EF_Configuration_comparator_output Configuration of comparator output
  * @{
  */

/**
  * @brief  Set comparator instance output polarity.
  * @rmtoll CSR      POLARITY       LL_COMP_SetOutputPolarity
  * @param  COMPx Comparator instance
  * @param  OutputPolarity This parameter can be one of the following values:
  *         @arg @ref LL_COMP_OUTPUTPOL_NONINVERTED
  *         @arg @ref LL_COMP_OUTPUTPOL_INVERTED
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetOutputPolarity(COMP_TypeDef *COMPx, uint32_t OutputPolarity)
{
  MODIFY_REG(COMPx->CSR, COMP_CSR_POLARITY, OutputPolarity);
}

/**
  * @brief  Get comparator instance output polarity.
  * @rmtoll CSR      POLARITY       LL_COMP_GetOutputPolarity
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_OUTPUTPOL_NONINVERTED
  *         @arg @ref LL_COMP_OUTPUTPOL_INVERTED
  */
__STATIC_INLINE uint32_t LL_COMP_GetOutputPolarity(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_POLARITY));
}

/**
  * @brief  Set comparator instance blanking source.
  * @note   Blanking source may be specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @note   Availability of parameters of blanking source from timer
  *         depends on timers availability on the selected device.
  * @rmtoll CSR      BLANKING       LL_COMP_SetOutputBlankingSource
  * @param  COMPx Comparator instance
  * @param  BlankingSource This parameter can be one of the following values:
  *         @arg @ref LL_COMP_BLANKINGSRC_NONE
  *         @arg @ref LL_COMP_BLANKINGSRC_TIM1_OC5  (1)
  *         @arg @ref LL_COMP_BLANKINGSRC_TIM2_OC3  (1)
  *
  *         (1) Parameter availability depending on timer availability
  *             on the selected device.
  * @retval None
  */
__STATIC_INLINE void LL_COMP_SetOutputBlankingSource(COMP_TypeDef *COMPx, uint32_t BlankingSource)
{
  MODIFY_REG(COMPx->CSR, COMP_CSR_BLANKING, BlankingSource);
}

/**
  * @brief  Get comparator instance blanking source.
  * @note   Availability of parameters of blanking source from timer
  *         depends on timers availability on the selected device.
  * @note   Blanking source may be specific to each comparator instance.
  *         Refer to description of parameters or to reference manual.
  * @rmtoll CSR      BLANKING       LL_COMP_GetOutputBlankingSource
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_BLANKINGSRC_NONE
  *         @arg @ref LL_COMP_BLANKINGSRC_TIM1_OC5  (1)
  *         @arg @ref LL_COMP_BLANKINGSRC_TIM2_OC3  (1)
  *
  *         (1) Parameter availability depending on timer availability
  *             on the selected device.
  */
__STATIC_INLINE uint32_t LL_COMP_GetOutputBlankingSource(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_BLANKING));
}

/**
  * @}
  */

/** @defgroup COMP_LL_EF_Operation Operation on comparator instance
  * @{
  */

/**
  * @brief  Enable comparator instance.
  * @note   After enable from off state, comparator requires a delay
  *         to reach reach propagation delay specification.
  *         Refer to device datasheet, parameter "tSTART".
  * @rmtoll CSR      EN             LL_COMP_Enable
  * @param  COMPx Comparator instance
  * @retval None
  */
__STATIC_INLINE void LL_COMP_Enable(COMP_TypeDef *COMPx)
{
  SET_BIT(COMPx->CSR, COMP_CSR_EN);
}

/**
  * @brief  Disable comparator instance.
  * @rmtoll CSR      EN             LL_COMP_Disable
  * @param  COMPx Comparator instance
  * @retval None
  */
__STATIC_INLINE void LL_COMP_Disable(COMP_TypeDef *COMPx)
{
  CLEAR_BIT(COMPx->CSR, COMP_CSR_EN);
}

/**
  * @brief  Get comparator enable state
  *         (0: COMP is disabled, 1: COMP is enabled)
  * @rmtoll CSR      EN             LL_COMP_IsEnabled
  * @param  COMPx Comparator instance
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_COMP_IsEnabled(COMP_TypeDef *COMPx)
{
  return ((READ_BIT(COMPx->CSR, COMP_CSR_EN) == (COMP_CSR_EN)) ? 1UL : 0UL);
}

/**
  * @brief  Lock comparator instance.
  * @note   Once locked, comparator configuration can be accessed in read-only.
  * @note   The only way to unlock the comparator is a device hardware reset.
  * @rmtoll CSR      LOCK           LL_COMP_Lock
  * @param  COMPx Comparator instance
  * @retval None
  */
__STATIC_INLINE void LL_COMP_Lock(COMP_TypeDef *COMPx)
{
  SET_BIT(COMPx->CSR, COMP_CSR_LOCK);
}

/**
  * @brief  Get comparator lock state
  *         (0: COMP is unlocked, 1: COMP is locked).
  * @note   Once locked, comparator configuration can be accessed in read-only.
  * @note   The only way to unlock the comparator is a device hardware reset.
  * @rmtoll CSR      LOCK           LL_COMP_IsLocked
  * @param  COMPx Comparator instance
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_COMP_IsLocked(COMP_TypeDef *COMPx)
{
  return ((READ_BIT(COMPx->CSR, COMP_CSR_LOCK) == (COMP_CSR_LOCK)) ? 1UL : 0UL);
}

/**
  * @brief  Read comparator instance output level.
  * @note   The comparator output level depends on the selected polarity
  *         (Refer to function @ref LL_COMP_SetOutputPolarity()).
  *         If the comparator polarity is not inverted:
  *          - Comparator output is low when the input plus
  *            is at a lower voltage than the input minus
  *          - Comparator output is high when the input plus
  *            is at a higher voltage than the input minus
  *         If the comparator polarity is inverted:
  *          - Comparator output is high when the input plus
  *            is at a lower voltage than the input minus
  *          - Comparator output is low when the input plus
  *            is at a higher voltage than the input minus
  * @rmtoll CSR      VALUE          LL_COMP_ReadOutputLevel
  * @param  COMPx Comparator instance
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_COMP_OUTPUT_LEVEL_LOW
  *         @arg @ref LL_COMP_OUTPUT_LEVEL_HIGH
  */
__STATIC_INLINE uint32_t LL_COMP_ReadOutputLevel(COMP_TypeDef *COMPx)
{
  return (uint32_t)(READ_BIT(COMPx->CSR, COMP_CSR_VALUE)
                    >> LL_COMP_OUTPUT_LEVEL_BITOFFSET_POS);
}

/**
  * @}
  */

#if defined(USE_FULL_LL_DRIVER)
/** @defgroup COMP_LL_EF_Init Initialization and de-initialization functions
  * @{
  */

ErrorStatus LL_COMP_DeInit(COMP_TypeDef *COMPx);
ErrorStatus LL_COMP_Init(COMP_TypeDef *COMPx, LL_COMP_InitTypeDef *COMP_InitStruct);
void        LL_COMP_StructInit(LL_COMP_InitTypeDef *COMP_InitStruct);

/**
  * @}
  */
#endif /* USE_FULL_LL_DRIVER */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */


/**
  * @}
  */

#ifdef __cplusplus
}
#endif

#endif /* STM32WBxx_LL_COMP_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/