/**
  ******************************************************************************
  * @file    stm32wbxx_hal_rcc.h
  * @author  MCD Application Team
  * @brief   Header file of RCC HAL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32WBxx_HAL_RCC_H
#define STM32WBxx_HAL_RCC_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32wbxx_hal_def.h"
#include "stm32wbxx_ll_rcc.h"
#include "stm32wbxx_ll_bus.h"


/** @addtogroup STM32WBxx_HAL_Driver
  * @{
  */

/** @addtogroup RCC
  * @{
  */

/* Private constants ---------------------------------------------------------*/
/** @addtogroup RCC_Private_Constants
  * @{
  */
/* Defines used for Flags */
#define CR_REG_INDEX              1U
#define BDCR_REG_INDEX            2U
#define CSR_REG_INDEX             3U
#define CRRCR_REG_INDEX           4U

#define RCC_FLAG_MASK             0x1FU
/**
  * @}
  */

/* Private macros ------------------------------------------------------------*/
/** @addtogroup RCC_Private_Macros
  * @{
  */

#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE)                             || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE)  == RCC_OSCILLATORTYPE_HSE)  || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI)  == RCC_OSCILLATORTYPE_HSI)  || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI48) == RCC_OSCILLATORTYPE_HSI48) || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_MSI)  == RCC_OSCILLATORTYPE_MSI)  || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI1) == RCC_OSCILLATORTYPE_LSI1) || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI2) == RCC_OSCILLATORTYPE_LSI2) || \
                                               (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE)  == RCC_OSCILLATORTYPE_LSE))


#define IS_RCC_HSE(__HSE__)  (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \
                              ((__HSE__) == RCC_HSE_BYPASS))

#define IS_RCC_LSE(__LSE__)  (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \
                              ((__LSE__) == RCC_LSE_BYPASS))

#define IS_RCC_HSI(__HSI__)  (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON))

#define IS_RCC_HSI_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (uint32_t)127U)

#define IS_RCC_LSI(__LSI__)  (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON))

#define IS_RCC_LSI2_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (uint32_t)15U)


#define IS_RCC_MSI(__MSI__)  (((__MSI__) == RCC_MSI_OFF) || ((__MSI__) == RCC_MSI_ON))


#define IS_RCC_MSICALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (uint32_t)255U)


#define IS_RCC_HSI48(__HSI48__)  (((__HSI48__) == RCC_HSI48_OFF) || ((__HSI48__) == RCC_HSI48_ON))


#define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) ||((__PLL__) == RCC_PLL_OFF) || \
                             ((__PLL__) == RCC_PLL_ON))

#define IS_RCC_PLLSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLSOURCE_NONE) || \
                                      ((__SOURCE__) == RCC_PLLSOURCE_MSI)  || \
                                      ((__SOURCE__) == RCC_PLLSOURCE_HSI)  || \
                                      ((__SOURCE__) == RCC_PLLSOURCE_HSE))

#define IS_RCC_PLLM_VALUE(__VALUE__) (((__VALUE__) == RCC_PLLM_DIV1)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV2)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV3)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV4)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV5)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV6)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV7)  || \
                                      ((__VALUE__) == RCC_PLLM_DIV8))

#define IS_RCC_PLLN_VALUE(__VALUE__) ((6U <= (__VALUE__)) && ((__VALUE__) <= 127U))

#define IS_RCC_PLLP_VALUE(__VALUE__) ((RCC_PLLP_DIV2 <= (__VALUE__)) && ((__VALUE__) <= RCC_PLLP_DIV32))

#define IS_RCC_PLLQ_VALUE(__VALUE__) ((RCC_PLLQ_DIV2 <= (__VALUE__)) && ((__VALUE__) <= RCC_PLLQ_DIV8))

#define IS_RCC_PLLR_VALUE(__VALUE__) ((RCC_PLLR_DIV2 <= (__VALUE__)) && ((__VALUE__) <= RCC_PLLR_DIV8))

#if defined(SAI1)
#define IS_RCC_PLLSAI1CLOCKOUT_VALUE(__VALUE__) (((((__VALUE__) & RCC_PLLSAI1_ADCCLK) == RCC_PLLSAI1_ADCCLK) || \
    (((__VALUE__) & RCC_PLLSAI1_SAI1CLK) == RCC_PLLSAI1_SAI1CLK) || \
    (((__VALUE__) & RCC_PLLSAI1_USBCLK)  == RCC_PLLSAI1_USBCLK)) && \
    (((__VALUE__) & ~(RCC_PLLSAI1_ADCCLK | RCC_PLLSAI1_SAI1CLK | RCC_PLLSAI1_USBCLK)) == 0U))
#endif
#define IS_RCC_MSI_CLOCK_RANGE(__RANGE__) (((__RANGE__) == RCC_MSIRANGE_0)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_1)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_2)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_3)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_4)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_5)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_6)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_7)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_8)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_9)  || \
                                           ((__RANGE__) == RCC_MSIRANGE_10) || \
                                           ((__RANGE__) == RCC_MSIRANGE_11))

#define IS_RCC_CLOCKTYPE(__CLK__)  ((1U <= (__CLK__)) && ((__CLK__) <= (RCC_CLOCKTYPE_SYSCLK | \
                                                                         RCC_CLOCKTYPE_HCLK  | \
                                                                         RCC_CLOCKTYPE_PCLK1 | \
                                                                         RCC_CLOCKTYPE_PCLK2 | \
                                                                         RCC_CLOCKTYPE_HCLK2 | \
                                                                         RCC_CLOCKTYPE_HCLK4)))

#define IS_RCC_SYSCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_MSI) || \
                                         ((__SOURCE__) == RCC_SYSCLKSOURCE_HSI) || \
                                         ((__SOURCE__) == RCC_SYSCLKSOURCE_HSE) || \
                                         ((__SOURCE__) == RCC_SYSCLKSOURCE_PLLCLK))

#define IS_RCC_HCLKx(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1)   || ((__HCLK__) == RCC_SYSCLK_DIV2)   || ((__HCLK__) == RCC_SYSCLK_DIV3)   || \
                               ((__HCLK__) == RCC_SYSCLK_DIV4)   || ((__HCLK__) == RCC_SYSCLK_DIV5)   || ((__HCLK__) == RCC_SYSCLK_DIV6)   || \
                               ((__HCLK__) == RCC_SYSCLK_DIV8)   || ((__HCLK__) == RCC_SYSCLK_DIV10)  || ((__HCLK__) == RCC_SYSCLK_DIV16)  || \
                               ((__HCLK__) == RCC_SYSCLK_DIV32)  || ((__HCLK__) == RCC_SYSCLK_DIV64)  || ((__HCLK__) == RCC_SYSCLK_DIV128) || \
                               ((__HCLK__) == RCC_SYSCLK_DIV256) || ((__HCLK__) == RCC_SYSCLK_DIV512))

#define IS_RCC_PCLKx(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \
                                ((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \
                                ((__PCLK__) == RCC_HCLK_DIV16))

#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_NONE) || \
                                         ((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \
                                         ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \
                                         ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV32))

#if defined(RCC_MCO3_SUPPORT)
#define IS_RCC_MCO(__MCOX__) (((__MCOX__) == RCC_MCO1) || \
                              ((__MCOX__) == RCC_MCO2) || \
                              ((__MCOX__) == RCC_MCO3))
#else
#define IS_RCC_MCO(__MCOX__) (((__MCOX__) == RCC_MCO1) || \
                              ((__MCOX__) == RCC_MCO2))
#endif

#define IS_RCC_MCO1SOURCE(__SOURCE__) (((__SOURCE__) == RCC_MCO1SOURCE_NOCLOCK) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_SYSCLK) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_MSI) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_HSI) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_HSE) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_PLLCLK) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_LSI1) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_LSI2) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_LSE) || \
                                       ((__SOURCE__) == RCC_MCO1SOURCE_HSI48))

#define IS_RCC_MCO2SOURCE(__SOURCE__) IS_RCC_MCO1SOURCE((__SOURCE__))
#define IS_RCC_MCO3SOURCE(__SOURCE__) IS_RCC_MCO1SOURCE((__SOURCE__))


#define IS_RCC_MCODIV(__DIV__) (((__DIV__) == RCC_MCODIV_1) || ((__DIV__) == RCC_MCODIV_2) || \
                                ((__DIV__) == RCC_MCODIV_4) || ((__DIV__) == RCC_MCODIV_8) || \
                                ((__DIV__) == RCC_MCODIV_16))


#define IS_RCC_LSE_DRIVE(__DRIVE__) (((__DRIVE__) == RCC_LSEDRIVE_LOW)        || \
                                     ((__DRIVE__) == RCC_LSEDRIVE_MEDIUMLOW)  || \
                                     ((__DRIVE__) == RCC_LSEDRIVE_MEDIUMHIGH) || \
                                     ((__DRIVE__) == RCC_LSEDRIVE_HIGH))

#define IS_RCC_STOP_WAKEUPCLOCK(__SOURCE__) (((__SOURCE__) == RCC_STOP_WAKEUPCLOCK_MSI) || \
                                             ((__SOURCE__) == RCC_STOP_WAKEUPCLOCK_HSI))
/**
  * @}
  */

/* Exported types ------------------------------------------------------------*/
/** @defgroup RCC_Exported_Types RCC Exported Types
  * @{
  */


/**
  * @brief  RCC PLL configuration structure definition
  */
typedef struct
{
  uint32_t PLLState;   /*!< The new state of the PLL.
                            This parameter must be a value of @ref RCC_PLL_Config                                 */

  uint32_t PLLSource;  /*!< RCC_PLLSource: PLL entry clock source.
                            This parameter must be a value of @ref RCC_PLL_Clock_Source               */

  uint32_t PLLM;       /*!< PLLM: Division factor for PLL VCO input clock.
                            This parameter must be a value of @ref RCC_PLLM_Clock_Divider             */

  uint32_t PLLN;       /*!< PLLN: Multiplication factor for PLL VCO output clock.
                            This parameter must be a number between Min_Data = 6 and Max_Data = 127    */

  uint32_t PLLP;       /*!< PLLP: Division factor for SAI & ADC clock.
                            This parameter must be a value of @ref RCC_PLLP_Clock_Divider             */

  uint32_t PLLQ;       /*!< PLLQ: Division factor for  RNG and USB clocks.
                            This parameter must be a value of @ref RCC_PLLQ_Clock_Divider             */

  uint32_t PLLR;       /*!< PLLR: Division for the main system clock.
                            User have to set the PLLR parameter correctly to not exceed max frequency 64MHZ.
                            This parameter must be a value of @ref RCC_PLLR_Clock_Divider             */

} RCC_PLLInitTypeDef;

/**
  * @brief  RCC Internal/External Oscillator (HSE, HSI, HSI48, MSI, LSE and LSI) configuration structure definition
  */
typedef struct
{
  uint32_t OscillatorType;       /*!< The oscillators to be configured.
                                      This parameter can be a combination of @ref RCC_Oscillator_Type             */

  uint32_t HSEState;             /*!< The new state of the HSE.
                                      This parameter can be a value of @ref RCC_HSE_Config                        */

  uint32_t LSEState;             /*!< The new state of the LSE.
                                      This parameter can be a value of @ref RCC_LSE_Config                        */

  uint32_t HSIState;             /*!< The new state of the HSI.
                                      This parameter can be a value of @ref RCC_HSI_Config                        */

  uint32_t HSICalibrationValue;  /*!< The calibration trimming value (default is @ref RCC_HSICALIBRATION_DEFAULT).*/

  uint32_t LSIState;             /*!< The new state of the LSI.
                                      This parameter can be a value of @ref RCC_LSI_Config                        */

  uint32_t LSI2CalibrationValue;  /*!< The LSI2 calibration trimming value .
                                    This parameter must be a number between Min_Data = 0x0 and Max_Data = 0xF     */

  uint32_t MSIState;             /*!< The new state of the MSI.
                                      This parameter can be a value of @ref RCC_MSI_Config */

  uint32_t MSICalibrationValue;  /*!< The calibration trimming value (default is @ref RCC_MSICALIBRATION_DEFAULT).
                                      This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF */

  uint32_t MSIClockRange;        /*!< The MSI frequency range.
                                      This parameter can be a value of @ref RCC_MSI_Clock_Range                   */

  uint32_t HSI48State;           /*!< The new state of the HSI48 .
                                      This parameter can be a value of @ref RCC_HSI48_Config                      */

  RCC_PLLInitTypeDef PLL;        /*!< Main PLL structure parameters                                               */

} RCC_OscInitTypeDef;

/**
  * @brief  RCC System, AHB and APB buses clock configuration structure definition
  */
typedef struct
{
  uint32_t ClockType;             /*!< The clock to be configured.
                                       This parameter can be a combination of @ref RCC_System_Clock_Type      */

  uint32_t SYSCLKSource;          /*!< The clock source used as system clock (SYSCLK).
                                       This parameter can be a value of @ref RCC_System_Clock_Source    */

  uint32_t AHBCLKDivider;         /*!< The AHBx clock (HCLK1) divider. This clock is derived from the system clock (SYSCLK).
                                       This parameter can be a value of @ref RCC_AHBx_Clock_Source       */

  uint32_t APB1CLKDivider;        /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK).
                                       This parameter can be a value of @ref RCC_APBx_Clock_Source      */

  uint32_t APB2CLKDivider;        /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK).
                                       This parameter can be a value of @ref RCC_APBx_Clock_Source      */

  uint32_t AHBCLK2Divider;        /*!< The AHB clock (HCLK2) divider. This clock is derived from the system clock (SYSCLK).
                                       This parameter can be a value of @ref RCC_AHBx_Clock_Source      */

  uint32_t AHBCLK4Divider;        /*!< The AHB shared clock (HCLK4) divider. This clock is derived from the system clock (SYSCLK).
                                       This parameter can be a value of @ref RCC_AHBx_Clock_Source       */

} RCC_ClkInitTypeDef;

/**
  * @}
  */

/* Exported constants --------------------------------------------------------*/
/** @defgroup RCC_Exported_Constants RCC Exported Constants
  * @{
  */

/** @defgroup RCC_Timeout_Value Timeout Values
  * @{
  */
#define RCC_DBP_TIMEOUT_VALUE          2U                   /* 2 ms (minimum Tick + 1)  */
#define RCC_LSE_TIMEOUT_VALUE          LSE_STARTUP_TIMEOUT  /* LSE timeout in ms        */
/**
  * @}
  */

/** @defgroup RCC_Oscillator_Type Oscillator Type
  * @{
  */
#define RCC_OSCILLATORTYPE_NONE        0x00000000U   /*!< Oscillator configuration unchanged  */
#define RCC_OSCILLATORTYPE_HSE         0x00000001U   /*!< HSE to configure                    */
#define RCC_OSCILLATORTYPE_HSI         0x00000002U   /*!< HSI to configure                    */
#define RCC_OSCILLATORTYPE_LSE         0x00000004U   /*!< LSE to configure                    */
#define RCC_OSCILLATORTYPE_LSI1        0x00000008U   /*!< LSI1 to configure                   */
#define RCC_OSCILLATORTYPE_LSI2        0x00000010U   /*!< LSI2 to configure                   */
#define RCC_OSCILLATORTYPE_MSI         0x00000020U   /*!< MSI to configure                    */
#define RCC_OSCILLATORTYPE_HSI48       0x00000040U   /*!< HSI48 to configure                  */
/**
  * @}
  */

/** @defgroup RCC_HSE_Config HSE Config
  * @{
  */
#define RCC_HSE_OFF                    0x00000000U                                /*!< HSE clock deactivation               */
#define RCC_HSE_ON                     RCC_CR_HSEON                               /*!< HSE clock activation                 */
#define RCC_HSE_BYPASS                 ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) /*!< External clock source for HSE clock  */
/**
  * @}
  */

/** @defgroup RCC_LSE_Config LSE Config
  * @{
  */
#define RCC_LSE_OFF                    0x00000000U                                    /*!< LSE clock deactivation */
#define RCC_LSE_ON                     RCC_BDCR_LSEON                                 /*!< LSE clock activation */
#define RCC_LSE_BYPASS                 ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) /*!< External clock source for LSE clock */
/**
  * @}
  */

/** @defgroup RCC_HSI_Config HSI Config
  * @{
  */
#define RCC_HSI_OFF                    0x00000000U  /*!< HSI clock deactivation */
#define RCC_HSI_ON                     RCC_CR_HSION /*!< HSI clock activation */

#define RCC_HSICALIBRATION_DEFAULT     64U          /*!< Default HSI calibration trimming value */
/**
  * @}
  */

/** @defgroup RCC_LSI_Config LSI Config
  * @{
  */
#define RCC_LSI_OFF                    0x00000000U                        /*!< LSI clock deactivation */
#define RCC_LSI_ON                     (RCC_CSR_LSI1ON | RCC_CSR_LSI2ON)  /*!< LSI1 or LSI2 clock activation */
/**
  * @}
  */

/** @defgroup RCC_MSI_Config MSI Config
  * @{
  */
#define RCC_MSI_OFF                    0x00000000U  /*!< MSI clock deactivation */
#define RCC_MSI_ON                     RCC_CR_MSION /*!< MSI clock activation */

#define RCC_MSICALIBRATION_DEFAULT     0U   /*!< Default MSI calibration trimming value */
/**
  * @}
  */


/** @defgroup RCC_HSI48_Config HSI48 Config
  * @{
  */
#define RCC_HSI48_OFF                  0x00000000U        /*!< HSI48 clock deactivation */
#define RCC_HSI48_ON                   RCC_CRRCR_HSI48ON  /*!< HSI48 clock activation */
/**
  * @}
  */


/** @defgroup RCC_PLL_Config PLL Config
  * @{
  */
#define RCC_PLL_NONE                   0x00000000U /*!< PLL configuration unchanged */
#define RCC_PLL_OFF                    0x00000001U /*!< PLL deactivation */
#define RCC_PLL_ON                     0x00000002U /*!< PLL activation */
/**
  * @}
  */

/** @defgroup RCC_PLLM_Clock_Divider PLLM Clock Divider
  * @{
  */
#define RCC_PLLM_DIV1                  LL_RCC_PLLM_DIV_1 /*!< PLLM division factor = 1  */
#define RCC_PLLM_DIV2                  LL_RCC_PLLM_DIV_2 /*!< PLLM division factor = 2  */
#define RCC_PLLM_DIV3                  LL_RCC_PLLM_DIV_3 /*!< PLLM division factor = 3  */
#define RCC_PLLM_DIV4                  LL_RCC_PLLM_DIV_4 /*!< PLLM division factor = 4  */
#define RCC_PLLM_DIV5                  LL_RCC_PLLM_DIV_5 /*!< PLLM division factor = 5  */
#define RCC_PLLM_DIV6                  LL_RCC_PLLM_DIV_6 /*!< PLLM division factor = 6  */
#define RCC_PLLM_DIV7                  LL_RCC_PLLM_DIV_7 /*!< PLLM division factor = 7  */
#define RCC_PLLM_DIV8                  LL_RCC_PLLM_DIV_8 /*!< PLLM division factor = 8  */
/**
  * @}
  */

/** @defgroup RCC_PLLP_Clock_Divider PLLP Clock Divider
  * @{
  */
#define RCC_PLLP_DIV2                  LL_RCC_PLLP_DIV_2  /*!< PLLP division factor = 2  */
#define RCC_PLLP_DIV3                  LL_RCC_PLLP_DIV_3  /*!< PLLP division factor = 3  */
#define RCC_PLLP_DIV4                  LL_RCC_PLLP_DIV_4  /*!< PLLP division factor = 4  */
#define RCC_PLLP_DIV5                  LL_RCC_PLLP_DIV_5  /*!< PLLP division factor = 5  */
#define RCC_PLLP_DIV6                  LL_RCC_PLLP_DIV_6  /*!< PLLP division factor = 6  */
#define RCC_PLLP_DIV7                  LL_RCC_PLLP_DIV_7  /*!< PLLP division factor = 7  */
#define RCC_PLLP_DIV8                  LL_RCC_PLLP_DIV_8  /*!< PLLP division factor = 8  */
#define RCC_PLLP_DIV9                  LL_RCC_PLLP_DIV_9  /*!< PLLP division factor = 9  */
#define RCC_PLLP_DIV10                 LL_RCC_PLLP_DIV_10 /*!< PLLP division factor = 10 */
#define RCC_PLLP_DIV11                 LL_RCC_PLLP_DIV_11 /*!< PLLP division factor = 11 */
#define RCC_PLLP_DIV12                 LL_RCC_PLLP_DIV_12 /*!< PLLP division factor = 12 */
#define RCC_PLLP_DIV13                 LL_RCC_PLLP_DIV_13 /*!< PLLP division factor = 13 */
#define RCC_PLLP_DIV14                 LL_RCC_PLLP_DIV_14 /*!< PLLP division factor = 14 */
#define RCC_PLLP_DIV15                 LL_RCC_PLLP_DIV_15 /*!< PLLP division factor = 15 */
#define RCC_PLLP_DIV16                 LL_RCC_PLLP_DIV_16 /*!< PLLP division factor = 16 */
#define RCC_PLLP_DIV17                 LL_RCC_PLLP_DIV_17 /*!< PLLP division factor = 17 */
#define RCC_PLLP_DIV18                 LL_RCC_PLLP_DIV_18 /*!< PLLP division factor = 18 */
#define RCC_PLLP_DIV19                 LL_RCC_PLLP_DIV_19 /*!< PLLP division factor = 19 */
#define RCC_PLLP_DIV20                 LL_RCC_PLLP_DIV_20 /*!< PLLP division factor = 20 */
#define RCC_PLLP_DIV21                 LL_RCC_PLLP_DIV_21 /*!< PLLP division factor = 21 */
#define RCC_PLLP_DIV22                 LL_RCC_PLLP_DIV_22 /*!< PLLP division factor = 22 */
#define RCC_PLLP_DIV23                 LL_RCC_PLLP_DIV_23 /*!< PLLP division factor = 23 */
#define RCC_PLLP_DIV24                 LL_RCC_PLLP_DIV_24 /*!< PLLP division factor = 24 */
#define RCC_PLLP_DIV25                 LL_RCC_PLLP_DIV_25 /*!< PLLP division factor = 25 */
#define RCC_PLLP_DIV26                 LL_RCC_PLLP_DIV_26 /*!< PLLP division factor = 26 */
#define RCC_PLLP_DIV27                 LL_RCC_PLLP_DIV_27 /*!< PLLP division factor = 27 */
#define RCC_PLLP_DIV28                 LL_RCC_PLLP_DIV_28 /*!< PLLP division factor = 28 */
#define RCC_PLLP_DIV29                 LL_RCC_PLLP_DIV_29 /*!< PLLP division factor = 29 */
#define RCC_PLLP_DIV30                 LL_RCC_PLLP_DIV_30 /*!< PLLP division factor = 30 */
#define RCC_PLLP_DIV31                 LL_RCC_PLLP_DIV_31 /*!< PLLP division factor = 31 */
#define RCC_PLLP_DIV32                 LL_RCC_PLLP_DIV_32 /*!< PLLP division factor = 32 */
/**
  * @}
  */

/** @defgroup RCC_PLLQ_Clock_Divider PLLQ Clock Divider
  * @{
  */
#define RCC_PLLQ_DIV2                  LL_RCC_PLLQ_DIV_2  /*!< PLLQ division factor = 2 */
#define RCC_PLLQ_DIV3                  LL_RCC_PLLQ_DIV_3  /*!< PLLQ division factor = 3 */
#define RCC_PLLQ_DIV4                  LL_RCC_PLLQ_DIV_4  /*!< PLLQ division factor = 4 */
#define RCC_PLLQ_DIV5                  LL_RCC_PLLQ_DIV_5  /*!< PLLQ division factor = 5 */
#define RCC_PLLQ_DIV6                  LL_RCC_PLLQ_DIV_6  /*!< PLLQ division factor = 6 */
#define RCC_PLLQ_DIV7                  LL_RCC_PLLQ_DIV_7  /*!< PLLQ division factor = 7 */
#define RCC_PLLQ_DIV8                  LL_RCC_PLLQ_DIV_8  /*!< PLLQ division factor = 8 */
/**
  * @}
  */

/** @defgroup RCC_PLLR_Clock_Divider PLLR Clock Divider
  * @{
  */
#define RCC_PLLR_DIV2                  LL_RCC_PLLR_DIV_2  /*!< PLLR division factor = 2 */
#define RCC_PLLR_DIV3                  LL_RCC_PLLR_DIV_3  /*!< PLLR division factor = 3 */
#define RCC_PLLR_DIV4                  LL_RCC_PLLR_DIV_4  /*!< PLLR division factor = 4 */
#define RCC_PLLR_DIV5                  LL_RCC_PLLR_DIV_5  /*!< PLLR division factor = 5 */
#define RCC_PLLR_DIV6                  LL_RCC_PLLR_DIV_6  /*!< PLLR division factor = 6 */
#define RCC_PLLR_DIV7                  LL_RCC_PLLR_DIV_7  /*!< PLLR division factor = 7 */
#define RCC_PLLR_DIV8                  LL_RCC_PLLR_DIV_8  /*!< PLLR division factor = 8 */
/**
  * @}
  */

/** @defgroup RCC_PLL_Clock_Source PLL Clock Source
  * @{
  */
#define RCC_PLLSOURCE_NONE             LL_RCC_PLLSOURCE_NONE /*!< No clock selected as PLL entry clock source  */
#define RCC_PLLSOURCE_MSI              LL_RCC_PLLSOURCE_MSI  /*!< MSI clock selected as PLL entry clock source */
#define RCC_PLLSOURCE_HSI              LL_RCC_PLLSOURCE_HSI  /*!< HSI clock selected as PLL entry clock source */
#define RCC_PLLSOURCE_HSE              LL_RCC_PLLSOURCE_HSE  /*!< HSE clock selected as PLL entry clock source */
/**
  * @}
  */

/** @defgroup RCC_PLL_Clock_Output PLL Clock Output
  * @{
  */
#define RCC_PLL_SYSCLK                 RCC_PLLCFGR_PLLREN      /*!< PLLCLK selection from main PLL */
#define RCC_PLL_USBCLK                 RCC_PLLCFGR_PLLQEN      /*!< PLLUSBCLK selection from main PLL */
#define RCC_PLL_RNGCLK                 RCC_PLLCFGR_PLLQEN      /*!< PLLRNGCLK selection from main PLL */
#if defined(SAI1)
#define RCC_PLL_SAI1CLK                RCC_PLLCFGR_PLLPEN      /*!< PLLSAI1CLK selection from main PLL */
#endif
#define RCC_PLL_ADCCLK                 RCC_PLLCFGR_PLLPEN      /*!< PLLADCCLK selection from main PLL */
#if defined(SPI_I2S_SUPPORT)
#define RCC_PLL_I2SCLK                 RCC_PLLCFGR_PLLPEN      /*!< PLLI2SCLK selection from main PLL */
#endif
/**
  * @}
  */

#if defined(SAI1)
/** @defgroup RCC_PLLSAI1_Clock_Output PLLSAI1 Clock Output
  * @{
  */
#define RCC_PLLSAI1_ADCCLK             RCC_PLLSAI1CFGR_PLLREN        /*!< PLLADCCLK selection from PLLSAI1 */
#define RCC_PLLSAI1_USBCLK             RCC_PLLSAI1CFGR_PLLQEN        /*!< USBCLK selection from PLLSAI1 */
#define RCC_PLLSAI1_SAI1CLK            RCC_PLLSAI1CFGR_PLLPEN       /*!< PLLSAI1CLK selection from PLLSAI1 */
/**
  * @}
  */
#endif

/** @defgroup RCC_MSI_Clock_Range MSI Clock Range
  * @{
  */
#define RCC_MSIRANGE_0                 LL_RCC_MSIRANGE_0  /*!< MSI = 100 KHz  */
#define RCC_MSIRANGE_1                 LL_RCC_MSIRANGE_1  /*!< MSI = 200 KHz  */
#define RCC_MSIRANGE_2                 LL_RCC_MSIRANGE_2  /*!< MSI = 400 KHz  */
#define RCC_MSIRANGE_3                 LL_RCC_MSIRANGE_3  /*!< MSI = 800 KHz  */
#define RCC_MSIRANGE_4                 LL_RCC_MSIRANGE_4  /*!< MSI = 1 MHz    */
#define RCC_MSIRANGE_5                 LL_RCC_MSIRANGE_5  /*!< MSI = 2 MHz    */
#define RCC_MSIRANGE_6                 LL_RCC_MSIRANGE_6  /*!< MSI = 4 MHz    */
#define RCC_MSIRANGE_7                 LL_RCC_MSIRANGE_7  /*!< MSI = 8 MHz    */
#define RCC_MSIRANGE_8                 LL_RCC_MSIRANGE_8  /*!< MSI = 16 MHz   */
#define RCC_MSIRANGE_9                 LL_RCC_MSIRANGE_9  /*!< MSI = 24 MHz   */
#define RCC_MSIRANGE_10                LL_RCC_MSIRANGE_10 /*!< MSI = 32 MHz   */
#define RCC_MSIRANGE_11                LL_RCC_MSIRANGE_11 /*!< MSI = 48 MHz   */
/**
  * @}
  */

/** @defgroup RCC_System_Clock_Type System Clock Type
  * @{
  */
#define RCC_CLOCKTYPE_SYSCLK           0x00000001U  /*!< SYSCLK to configure */
#define RCC_CLOCKTYPE_HCLK             0x00000002U  /*!< HCLK to configure */
#define RCC_CLOCKTYPE_PCLK1            0x00000004U  /*!< PCLK1 to configure */
#define RCC_CLOCKTYPE_PCLK2            0x00000008U  /*!< PCLK2 to configure */
#define RCC_CLOCKTYPE_HCLK2            0x00000020U  /*!< HCLK2 to configure */
#define RCC_CLOCKTYPE_HCLK4            0x00000040U  /*!< HCLK4 to configure */
/**
  * @}
  */

/** @defgroup RCC_System_Clock_Source System Clock Source
  * @{
  */
#define RCC_SYSCLKSOURCE_MSI           LL_RCC_SYS_CLKSOURCE_MSI    /*!< MSI selection as system clock */
#define RCC_SYSCLKSOURCE_HSI           LL_RCC_SYS_CLKSOURCE_HSI    /*!< HSI selection as system clock */
#define RCC_SYSCLKSOURCE_HSE           LL_RCC_SYS_CLKSOURCE_HSE    /*!< HSE selection as system clock */
#define RCC_SYSCLKSOURCE_PLLCLK        LL_RCC_SYS_CLKSOURCE_PLL    /*!< PLL selection as system clock */
/**
  * @}
  */

/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status
  * @{
  */
#define RCC_SYSCLKSOURCE_STATUS_MSI    LL_RCC_SYS_CLKSOURCE_STATUS_MSI   /*!< MSI used as system clock */
#define RCC_SYSCLKSOURCE_STATUS_HSI    LL_RCC_SYS_CLKSOURCE_STATUS_HSI   /*!< HSI used as system clock */
#define RCC_SYSCLKSOURCE_STATUS_HSE    LL_RCC_SYS_CLKSOURCE_STATUS_HSE   /*!< HSE used as system clock */
#define RCC_SYSCLKSOURCE_STATUS_PLLCLK LL_RCC_SYS_CLKSOURCE_STATUS_PLL   /*!< PLL used as system clock */
/**
  * @}
  */

/** @defgroup RCC_AHBx_Clock_Source AHB Clock Source
  * @{
  */
#define RCC_SYSCLK_DIV1                LL_RCC_SYSCLK_DIV_1     /*!< SYSCLK not divided */
#define RCC_SYSCLK_DIV2                LL_RCC_SYSCLK_DIV_2     /*!< SYSCLK divided by 2 */
#define RCC_SYSCLK_DIV3                LL_RCC_SYSCLK_DIV_3     /*!< SYSCLK divided by 3 */
#define RCC_SYSCLK_DIV4                LL_RCC_SYSCLK_DIV_4     /*!< SYSCLK divided by 4 */
#define RCC_SYSCLK_DIV5                LL_RCC_SYSCLK_DIV_5     /*!< SYSCLK divided by 5 */
#define RCC_SYSCLK_DIV6                LL_RCC_SYSCLK_DIV_6     /*!< SYSCLK divided by 6 */
#define RCC_SYSCLK_DIV8                LL_RCC_SYSCLK_DIV_8     /*!< SYSCLK divided by 8 */
#define RCC_SYSCLK_DIV10               LL_RCC_SYSCLK_DIV_10    /*!< SYSCLK divided by 10 */
#define RCC_SYSCLK_DIV16               LL_RCC_SYSCLK_DIV_16    /*!< SYSCLK divided by 16 */
#define RCC_SYSCLK_DIV32               LL_RCC_SYSCLK_DIV_32    /*!< SYSCLK divided by 32 */
#define RCC_SYSCLK_DIV64               LL_RCC_SYSCLK_DIV_64    /*!< SYSCLK divided by 64 */
#define RCC_SYSCLK_DIV128              LL_RCC_SYSCLK_DIV_128   /*!< SYSCLK divided by 128 */
#define RCC_SYSCLK_DIV256              LL_RCC_SYSCLK_DIV_256   /*!< SYSCLK divided by 256 */
#define RCC_SYSCLK_DIV512              LL_RCC_SYSCLK_DIV_512   /*!< SYSCLK divided by 512 */
/**
  * @}
  */

/** @defgroup RCC_APBx_Clock_Source APB1 Clock Source
* @{
*/
#define RCC_HCLK_DIV1                  LL_RCC_APB1_DIV_1    /*!< HCLK not divided */
#define RCC_HCLK_DIV2                  LL_RCC_APB1_DIV_2    /*!< HCLK divided by 2 */
#define RCC_HCLK_DIV4                  LL_RCC_APB1_DIV_4    /*!< HCLK divided by 4 */
#define RCC_HCLK_DIV8                  LL_RCC_APB1_DIV_8    /*!< HCLK divided by 8 */
#define RCC_HCLK_DIV16                 LL_RCC_APB1_DIV_16   /*!< HCLK divided by 16 */
/**
  * @}
  */

/** @defgroup RCC_RTC_Clock_Source RTC Clock Source
  * @{
  */
#define RCC_RTCCLKSOURCE_NONE           LL_RCC_RTC_CLKSOURCE_NONE       /*!< No clock used as RTC clock */
#define RCC_RTCCLKSOURCE_LSE            LL_RCC_RTC_CLKSOURCE_LSE        /*!< LSE oscillator clock used as RTC clock */
#define RCC_RTCCLKSOURCE_LSI            LL_RCC_RTC_CLKSOURCE_LSI        /*!< LSI oscillator clock used as RTC clock */
#define RCC_RTCCLKSOURCE_HSE_DIV32      LL_RCC_RTC_CLKSOURCE_HSE_DIV32  /*!< HSE oscillator clock divided by 32 used as RTC clock */
/**
  * @}
  */

/** @defgroup RCC_MCO_Index MCO Index
  * @{
  */
#define RCC_MCO1                       0x00000000U          /*!< MCO1 index */
#define RCC_MCO2                       0x00000001U          /*!< MCO2 index */
#if defined(RCC_MCO3_SUPPORT)
#define RCC_MCO3                       0x00000002U          /*!< MCO3 index */
#endif

#define RCC_MCO                        RCC_MCO1             /*!< MCO1 to be compliant with other families with 1 MCO*/
/**
  * @}
  */

/** @defgroup RCC_MCO1_Clock_Source MCO1 Clock Source
  * @{
  */
#define RCC_MCO1SOURCE_NOCLOCK         LL_RCC_MCO1SOURCE_NOCLOCK          /*!< MCO1 output disabled, no clock on MCO1 */
#define RCC_MCO1SOURCE_SYSCLK          LL_RCC_MCO1SOURCE_SYSCLK           /*!< SYSCLK selection as MCO1 source */
#define RCC_MCO1SOURCE_MSI             LL_RCC_MCO1SOURCE_MSI              /*!< MSI selection as MCO1 source */
#define RCC_MCO1SOURCE_HSI             LL_RCC_MCO1SOURCE_HSI              /*!< HSI selection as MCO1 source */
#define RCC_MCO1SOURCE_HSE             LL_RCC_MCO1SOURCE_HSE              /*!< HSE after stabilization selection as MCO1 source */
#define RCC_MCO1SOURCE_PLLCLK          LL_RCC_MCO1SOURCE_PLLCLK           /*!< PLLCLK selection as MCO1 source */
#define RCC_MCO1SOURCE_LSI1            LL_RCC_MCO1SOURCE_LSI1             /*!< LSI1 selection as MCO1 source */
#define RCC_MCO1SOURCE_LSI2            LL_RCC_MCO1SOURCE_LSI2             /*!< LSI2 selection as MCO1 source */
#define RCC_MCO1SOURCE_LSE             LL_RCC_MCO1SOURCE_LSE              /*!< LSE selection as MCO1 source */
#define RCC_MCO1SOURCE_HSI48           LL_RCC_MCO1SOURCE_HSI48            /*!< HSI48 selection as MCO1 source */
#define RCC_MCO1SOURCE_HSE_BEFORE_STAB LL_RCC_MCO1SOURCE_HSE_BEFORE_STAB  /*!< HSE before stabilization selection as MCO1 source */

/**
  * @}
  */

/** @defgroup RCC_MCOx_Clock_Prescaler MCO Clock Prescaler
  * @{
  */
#define RCC_MCODIV_1                   LL_RCC_MCO1_DIV_1                  /*!< MCO not divided */
#define RCC_MCODIV_2                   LL_RCC_MCO1_DIV_2                  /*!< MCO divided by 2 */
#define RCC_MCODIV_4                   LL_RCC_MCO1_DIV_4                  /*!< MCO divided by 4 */
#define RCC_MCODIV_8                   LL_RCC_MCO1_DIV_8                  /*!< MCO divided by 8 */
#define RCC_MCODIV_16                  LL_RCC_MCO1_DIV_16                 /*!< MCO divided by 16 */
/**
  * @}
  */

/** @defgroup RCC_HSEAMPTHRESHOLD HSE bias current factor
  * @{
  */
#define RCC_HSEAMPTHRESHOLD_1_2       LL_RCC_HSEAMPTHRESHOLD_1_2           /*!< HSE bias current factor 1/2 */
#define RCC_HSEAMPTHRESHOLD_3_4       LL_RCC_HSEAMPTHRESHOLD_3_4           /*!< HSE bias current factor 3/4 */

/**
  * @}
  */

/** @defgroup RCC_HSE_CURRENTMAX HSE current max limit
  * @{
  */
#define RCC_HSE_CURRENTMAX_0           LL_RCC_HSE_CURRENTMAX_0             /*!< HSE current max limit 0.18 mA/V */
#define RCC_HSE_CURRENTMAX_1           LL_RCC_HSE_CURRENTMAX_1             /*!< HSE current max limit 0.57 mA/V */
#define RCC_HSE_CURRENTMAX_2           LL_RCC_HSE_CURRENTMAX_2             /*!< HSE current max limit 0.78 mA/V */
#define RCC_HSE_CURRENTMAX_3           LL_RCC_HSE_CURRENTMAX_3             /*!< HSE current max limit 1.13 mA/V */
#define RCC_HSE_CURRENTMAX_4           LL_RCC_HSE_CURRENTMAX_4             /*!< HSE current max limit 0.61 mA/V */
#define RCC_HSE_CURRENTMAX_5           LL_RCC_HSE_CURRENTMAX_5             /*!< HSE current max limit 1.65 mA/V */
#define RCC_HSE_CURRENTMAX_6           LL_RCC_HSE_CURRENTMAX_6             /*!< HSE current max limit 2.12 mA/V */
#define RCC_HSE_CURRENTMAX_7           LL_RCC_HSE_CURRENTMAX_7             /*!< HSE current max limit 2.84 mA/V */

/**
  * @}
  */

/** @defgroup RCC_Interrupt Interrupts
  * @{
  */
#define RCC_IT_LSI1RDY                 LL_RCC_CIFR_LSI1RDYF     /*!< LSI1 Ready Interrupt flag */
#define RCC_IT_LSI2RDY                 LL_RCC_CIFR_LSI2RDYF     /*!< LSI2 Ready Interrupt flag */
#define RCC_IT_LSERDY                  LL_RCC_CIFR_LSERDYF      /*!< LSE Ready Interrupt flag */
#define RCC_IT_MSIRDY                  LL_RCC_CIFR_MSIRDYF      /*!< MSI Ready Interrupt flag */
#define RCC_IT_HSIRDY                  LL_RCC_CIFR_HSIRDYF      /*!< HSI Ready Interrupt flag */
#define RCC_IT_HSERDY                  LL_RCC_CIFR_HSERDYF      /*!< HSE Ready Interrupt flag */
#define RCC_IT_PLLRDY                  LL_RCC_CIFR_PLLRDYF      /*!< PLL Ready Interrupt flag */
#if defined(SAI1)
#define RCC_IT_PLLSAI1RDY              LL_RCC_CIFR_PLLSAI1RDYF  /*!< PLLSAI1 Ready Interrupt flag */
#endif
#define RCC_IT_HSECSS                  LL_RCC_CIFR_CSSF         /*!< HSE Clock Security System Interrupt flag */
#define RCC_IT_LSECSS                  LL_RCC_CIFR_LSECSSF      /*!< LSE Clock Security System Interrupt flag */
#define RCC_IT_HSI48RDY                LL_RCC_CIFR_HSI48RDYF    /*!< HSI48 Ready Interrupt flag */
/**
  * @}
  */


/** @defgroup RCC_Flag Flags
  *        Elements values convention: XXXYYYYYb
  *           - YYYYY  : Flag position in the register
  *           - XXX  : Register index
  *                 - 001: CR register
  *                 - 010: BDCR register
  *                 - 011: CSR register
  *                 - 100: CRRCR register
  * @{
  */
/* Flags in the CR register */
#define RCC_FLAG_MSIRDY                ((CR_REG_INDEX << 5U) | RCC_CR_MSIRDY_Pos)      /*!< MSI Ready flag */
#define RCC_FLAG_HSIRDY                ((CR_REG_INDEX << 5U) | RCC_CR_HSIRDY_Pos)      /*!< HSI Ready flag */
#define RCC_FLAG_HSERDY                ((CR_REG_INDEX << 5U) | RCC_CR_HSERDY_Pos)      /*!< HSE Ready flag */
#define RCC_FLAG_PLLRDY                ((CR_REG_INDEX << 5U) | RCC_CR_PLLRDY_Pos)      /*!< PLL Ready flag */
#if defined(SAI1)
#define RCC_FLAG_PLLSAI1RDY            ((CR_REG_INDEX << 5U) | RCC_CR_PLLSAI1RDY_Pos)  /*!< PLLSAI1 Ready flag */
#endif

/* Flags in the BDCR register */
#define RCC_FLAG_LSERDY                ((BDCR_REG_INDEX << 5U) | RCC_BDCR_LSERDY_Pos)  /*!< LSE Ready flag */
#define RCC_FLAG_LSECSSD               ((BDCR_REG_INDEX << 5U) | RCC_BDCR_LSECSSD_Pos) /*!< LSE Clock Security System failure detection flag */

/* Flags in the CSR register */
#define RCC_FLAG_LSI1RDY               ((CSR_REG_INDEX << 5U) | RCC_CSR_LSI1RDY_Pos)   /*!< LSI1 Ready flag */
#define RCC_FLAG_LSI2RDY               ((CSR_REG_INDEX << 5U) | RCC_CSR_LSI2RDY_Pos)   /*!< LSI2 Ready flag */
#define RCC_FLAG_OBLRST                ((CSR_REG_INDEX << 5U) | RCC_CSR_OBLRSTF_Pos)   /*!< Option Byte Loader reset flag */
#define RCC_FLAG_PINRST                ((CSR_REG_INDEX << 5U) | RCC_CSR_PINRSTF_Pos)   /*!< Pin reset flag (NRST pin) */
#define RCC_FLAG_BORRST                ((CSR_REG_INDEX << 5U) | RCC_CSR_BORRSTF_Pos)   /*!< BOR reset flag */
#define RCC_FLAG_SFTRST                ((CSR_REG_INDEX << 5U) | RCC_CSR_SFTRSTF_Pos)   /*!< Software Reset flag */
#define RCC_FLAG_IWDGRST               ((CSR_REG_INDEX << 5U) | RCC_CSR_IWDGRSTF_Pos)  /*!< Watchdog reset flag */
#define RCC_FLAG_WWDGRST               ((CSR_REG_INDEX << 5U) | RCC_CSR_WWDGRSTF_Pos)  /*!< Window watchdog reset flag */
#define RCC_FLAG_LPWRRST               ((CSR_REG_INDEX << 5U) | RCC_CSR_LPWRRSTF_Pos)  /*!< Low-Power reset flag */

/* Flags in the CRRCR register */
#define RCC_FLAG_HSI48RDY              ((CRRCR_REG_INDEX << 5U) | RCC_CRRCR_HSI48RDY_Pos) /*!< HSI48 Ready flag */

/**
  * @}
  */

/** @defgroup RCC_LSEDrive_Config LSE Drive Configuration
  * @{
  */
#define RCC_LSEDRIVE_LOW                 LL_RCC_LSEDRIVE_LOW            /*!< LSE low drive capability */
#define RCC_LSEDRIVE_MEDIUMLOW           LL_RCC_LSEDRIVE_MEDIUMLOW      /*!< LSE medium low drive capability */
#define RCC_LSEDRIVE_MEDIUMHIGH          LL_RCC_LSEDRIVE_MEDIUMHIGH     /*!< LSE medium high drive capability */
#define RCC_LSEDRIVE_HIGH                LL_RCC_LSEDRIVE_HIGH           /*!< LSE high drive capability */
/**
  * @}
  */

/** @defgroup RCC_Stop_WakeUpClock Wake-Up from STOP Clock
  * @{
  */
#define RCC_STOP_WAKEUPCLOCK_MSI       LL_RCC_STOP_WAKEUPCLOCK_MSI       /*!< MSI selection after wake-up from STOP */
#define RCC_STOP_WAKEUPCLOCK_HSI       LL_RCC_STOP_WAKEUPCLOCK_HSI       /*!< HSI selection after wake-up from STOP */
/**
  * @}
  */

/**
  * @}
  */

/* Exported macros -----------------------------------------------------------*/

/** @defgroup RCC_Exported_Macros RCC Exported Macros
  * @{
  */

/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
  * @brief  Enable or disable the AHB1 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_DMA1_CLK_ENABLE()            LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_CLK_ENABLE()            LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_CLK_ENABLE()         LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_CRC_CLK_ENABLE()             LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_CLK_ENABLE()             LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_DMA1_CLK_DISABLE()           LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_CLK_DISABLE()           LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_CLK_DISABLE()        LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_CRC_CLK_DISABLE()            LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_CLK_DISABLE()            LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_TSC)

/**
  * @}
  */

/** @defgroup RCC_AHB2_Peripheral_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
  * @brief  Enable or disable the AHB2 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_GPIOA_CLK_ENABLE()           LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_CLK_ENABLE()           LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_CLK_ENABLE()           LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOC)

#if defined(GPIOD)
#define __HAL_RCC_GPIOD_CLK_ENABLE()           LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_CLK_ENABLE()           LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_CLK_ENABLE()           LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOH)

#define __HAL_RCC_ADC_CLK_ENABLE()             LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_AES1_CLK_ENABLE()            LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_AES1)
#endif
#define __HAL_RCC_GPIOA_CLK_DISABLE()          LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_CLK_DISABLE()          LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_CLK_DISABLE()          LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_CLK_DISABLE()          LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_CLK_DISABLE()          LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_CLK_DISABLE()          LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_GPIOH)

#define __HAL_RCC_ADC_CLK_DISABLE()            LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_ADC)

#if defined(AES1)
#define __HAL_RCC_AES1_CLK_DISABLE()           LL_AHB2_GRP1_DisableClock(LL_AHB2_GRP1_PERIPH_AES1)
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
  * @brief  Enable or disable the AHB3 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_CLK_ENABLE()         LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_CLK_ENABLE()             LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_CLK_ENABLE()            LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_CLK_ENABLE()             LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_HSEM_CLK_ENABLE()            LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_IPCC_CLK_ENABLE()            LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_FLASH_CLK_ENABLE()           LL_AHB3_GRP1_EnableClock(LL_AHB3_GRP1_PERIPH_FLASH)

#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_CLK_DISABLE()        LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_CLK_DISABLE()            LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_CLK_DISABLE()           LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_CLK_DISABLE()            LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_HSEM_CLK_DISABLE()           LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_IPCC_CLK_DISABLE()           LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_FLASH_CLK_DISABLE()          LL_AHB3_GRP1_DisableClock(LL_AHB3_GRP1_PERIPH_FLASH)

/**
  * @}
  */

/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
  * @brief  Enable or disable the APB1 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_RTCAPB_CLK_ENABLE()          LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_WWDG_CLK_ENABLE()            LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_WWDG)
#define __HAL_RCC_TIM2_CLK_ENABLE()            LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_CLK_ENABLE()             LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_SPI2_CLK_ENABLE()            LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_CLK_ENABLE()            LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_CLK_ENABLE()            LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_CLK_ENABLE()             LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_CLK_ENABLE()             LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_CLK_ENABLE()          LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_LPTIM1)
#define __HAL_RCC_LPTIM2_CLK_ENABLE()          LL_APB1_GRP2_EnableClock(LL_APB1_GRP2_PERIPH_LPTIM2)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_CLK_ENABLE()         LL_APB1_GRP2_EnableClock(LL_APB1_GRP2_PERIPH_LPUART1)
#endif

#define __HAL_RCC_RTCAPB_CLK_DISABLE()         LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_TIM2_CLK_DISABLE()           LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_CLK_DISABLE()            LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_SPI2_CLK_DISABLE()           LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_CLK_DISABLE()           LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_CLK_DISABLE()           LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_CLK_DISABLE()            LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_CLK_DISABLE()            LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_CLK_DISABLE()         LL_APB1_GRP1_DisableClock(LL_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_LPTIM2_CLK_DISABLE()         LL_APB1_GRP2_DisableClock(LL_APB1_GRP2_PERIPH_LPTIM2)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_CLK_DISABLE()        LL_APB1_GRP2_DisableClock(LL_APB1_GRP2_PERIPH_LPUART1)
#endif

/**
  * @}
  */

/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
  * @brief  Enable or disable the APB2 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_TIM1_CLK_ENABLE()            LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_CLK_ENABLE()            LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_CLK_ENABLE()          LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_CLK_ENABLE()           LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_CLK_ENABLE()           LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_CLK_ENABLE()            LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_TIM1_CLK_DISABLE()           LL_APB2_GRP1_DisableClock(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_CLK_DISABLE()           LL_APB2_GRP1_DisableClock(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_CLK_DISABLE()         LL_APB2_GRP1_DisableClock(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_CLK_DISABLE()          LL_APB2_GRP1_DisableClock(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_CLK_DISABLE()          LL_APB2_GRP1_DisableClock(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_CLK_DISABLE()           LL_APB2_GRP1_DisableClock(LL_APB2_GRP1_PERIPH_SAI1)
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the AHB1 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_DMA1_IS_CLK_ENABLED()        LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_IS_CLK_ENABLED()        LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_IS_CLK_ENABLED()     LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_CRC_IS_CLK_ENABLED()         LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_IS_CLK_ENABLED()         LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_DMA1_IS_CLK_DISABLED()       !(LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_DMA1))
#if defined(DMA2)
#define __HAL_RCC_DMA2_IS_CLK_DISABLED()       !(LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_DMA2))
#endif
#define __HAL_RCC_DMAMUX1_IS_CLK_DISABLED()    !(LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_DMAMUX1))
#define __HAL_RCC_CRC_IS_CLK_DISABLED()        !(LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_CRC))
#define __HAL_RCC_TSC_IS_CLK_DISABLED()        !(LL_AHB1_GRP1_IsEnabledClock(LL_AHB1_GRP1_PERIPH_TSC))

/**
  * @}
  */

/** @defgroup RCC_AHB2_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the AHB2 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_GPIOA_IS_CLK_ENABLED()       LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_IS_CLK_ENABLED()       LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_IS_CLK_ENABLED()       LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_IS_CLK_ENABLED()       LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_IS_CLK_ENABLED()       LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_IS_CLK_ENABLED()       LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_ADC_IS_CLK_ENABLED()         LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_AES1_IS_CLK_ENABLED()        LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_GPIOA_IS_CLK_DISABLED()      !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOA))
#define __HAL_RCC_GPIOB_IS_CLK_DISABLED()      !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOB))
#define __HAL_RCC_GPIOC_IS_CLK_DISABLED()      !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOC))
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_IS_CLK_DISABLED()      !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOD))
#endif
#define __HAL_RCC_GPIOE_IS_CLK_DISABLED()      !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOE))
#define __HAL_RCC_GPIOH_IS_CLK_DISABLED()      !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_GPIOH))
#define __HAL_RCC_ADC_IS_CLK_DISABLED()        !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_ADC))
#if defined(AES1)
#define __HAL_RCC_AES1_IS_CLK_DISABLED()       !(LL_AHB2_GRP1_IsEnabledClock(LL_AHB2_GRP1_PERIPH_AES1))
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB3_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the AHB3 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_IS_CLK_ENABLED()      LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_IS_CLK_ENABLED()          LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_IS_CLK_ENABLED()         LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_IS_CLK_ENABLED()          LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_HSEM_IS_CLK_ENABLED()         LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_IPCC_IS_CLK_ENABLED()         LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_FLASH_IS_CLK_ENABLED()        LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_FLASH)

#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_IS_CLK_DISABLED()     !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_QUADSPI))
#endif
#define __HAL_RCC_PKA_IS_CLK_DISABLED()         !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_PKA))
#define __HAL_RCC_AES2_IS_CLK_DISABLED()        !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_AES2))
#define __HAL_RCC_RNG_IS_CLK_DISABLED()         !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_RNG))
#define __HAL_RCC_HSEM_IS_CLK_DISABLED()        !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_HSEM))
#define __HAL_RCC_IPCC_IS_CLK_DISABLED()        !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_IPCC))
#define __HAL_RCC_FLASH_IS_CLK_DISABLED()       !(LL_AHB3_GRP1_IsEnabledClock(LL_AHB3_GRP1_PERIPH_FLASH))

/**
  * @}
  */

/** @defgroup RCC_APB1_Clock_Enable_Disable_Status APB1 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the APB1 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_RTCAPB_IS_CLK_ENABLED()         LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_WWDG_IS_CLK_ENABLED()           LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_WWDG)
#define __HAL_RCC_TIM2_IS_CLK_ENABLED()           LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_IS_CLK_ENABLED()            LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_SPI2_IS_CLK_ENABLED()           LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_IS_CLK_ENABLED()           LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_IS_CLK_ENABLED()           LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_IS_CLK_ENABLED()            LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_IS_CLK_ENABLED()            LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_IS_CLK_ENABLED()         LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_LPTIM2_IS_CLK_ENABLED()         LL_APB1_GRP2_IsEnabledClock(LL_APB1_GRP2_PERIPH_LPTIM2)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_IS_CLK_ENABLED()        LL_APB1_GRP2_IsEnabledClock(LL_APB1_GRP2_PERIPH_LPUART1)
#endif

#define __HAL_RCC_RTCAPB_IS_CLK_DISABLED()        !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_RTCAPB))
#define __HAL_RCC_WWDG_IS_CLK_DISABLED()          !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_WWDG))
#define __HAL_RCC_TIM2_IS_CLK_DISABLED()          !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_TIM2))
#if defined(LCD)
#define __HAL_RCC_LCD_IS_CLK_DISABLED()           !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_LCD))
#endif
#if defined(SPI2)
#define __HAL_RCC_SPI2_IS_CLK_DISABLED()          !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_SPI2))
#endif
#define __HAL_RCC_I2C1_IS_CLK_DISABLED()          !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_I2C1))
#if defined(I2C3)
#define __HAL_RCC_I2C3_IS_CLK_DISABLED()          !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_I2C3))
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_IS_CLK_DISABLED()           !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_CRS))
#endif
#if defined(USB)
#define __HAL_RCC_USB_IS_CLK_DISABLED()           !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_USB))
#endif
#define __HAL_RCC_LPTIM1_IS_CLK_DISABLED()        !(LL_APB1_GRP1_IsEnabledClock(LL_APB1_GRP1_PERIPH_LPTIM1))

#define __HAL_RCC_LPTIM2_IS_CLK_DISABLED()        !(LL_APB1_GRP2_IsEnabledClock(LL_APB1_GRP2_PERIPH_LPTIM2))
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_IS_CLK_DISABLED()       !(LL_APB1_GRP2_IsEnabledClock(LL_APB1_GRP2_PERIPH_LPUART1))
#endif

/**
  * @}
  */

/** @defgroup RCC_APB2_Clock_Enable_Disable_Status APB2 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the APB2 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_TIM1_IS_CLK_ENABLED()           LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_IS_CLK_ENABLED()           LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_IS_CLK_ENABLED()         LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_IS_CLK_ENABLED()          LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_IS_CLK_ENABLED()          LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_IS_CLK_ENABLED()           LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_SAI1)
#endif


#define __HAL_RCC_TIM1_IS_CLK_DISABLED()          !(LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_TIM1))
#define __HAL_RCC_SPI1_IS_CLK_DISABLED()          !(LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_SPI1))
#define __HAL_RCC_USART1_IS_CLK_DISABLED()        !(LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_USART1))
#define __HAL_RCC_TIM16_IS_CLK_DISABLED()         !(LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_TIM16))
#define __HAL_RCC_TIM17_IS_CLK_DISABLED()         !(LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_TIM17))
#if defined(SAI1)
#define __HAL_RCC_SAI1_IS_CLK_DISABLED()          !(LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_SAI1))
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
  * @brief  Enable or disable the AHB1 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2DMA1_CLK_ENABLE()            LL_C2_AHB1_GRP1_EnableClock(LL_C2_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_CLK_ENABLE()            LL_C2_AHB1_GRP1_EnableClock(LL_C2_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_C2DMAMUX1_CLK_ENABLE()         LL_C2_AHB1_GRP1_EnableClock(LL_C2_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_C2SRAM1_CLK_ENABLE()           LL_C2_AHB1_GRP1_EnableClock(LL_C2_AHB1_GRP1_PERIPH_SRAM1)
#define __HAL_RCC_C2CRC_CLK_ENABLE()             LL_C2_AHB1_GRP1_EnableClock(LL_C2_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_C2TSC_CLK_ENABLE()             LL_C2_AHB1_GRP1_EnableClock(LL_C2_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_C2DMA1_CLK_DISABLE()           LL_C2_AHB1_GRP1_DisableClock(LL_C2_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_CLK_DISABLE()           LL_C2_AHB1_GRP1_DisableClock(LL_C2_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_C2DMAMUX1_CLK_DISABLE()        LL_C2_AHB1_GRP1_DisableClock(LL_C2_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_C2SRAM1_CLK_DISABLE()          LL_C2_AHB1_GRP1_DisableClock(LL_C2_AHB1_GRP1_PERIPH_SRAM1)
#define __HAL_RCC_C2CRC_CLK_DISABLE()            LL_C2_AHB1_GRP1_DisableClock(LL_C2_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_C2TSC_CLK_DISABLE()            LL_C2_AHB1_GRP1_DisableClock(LL_C2_AHB1_GRP1_PERIPH_TSC)

/**
  * @}
  */

/** @defgroup RCC_AHB2_Peripheral_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
  * @brief  Enable or disable the AHB2 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2GPIOA_CLK_ENABLE()           LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_C2GPIOB_CLK_ENABLE()           LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_C2GPIOC_CLK_ENABLE()           LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_CLK_ENABLE()           LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_C2GPIOE_CLK_ENABLE()           LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_C2GPIOH_CLK_ENABLE()           LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_C2ADC_CLK_ENABLE()             LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_C2AES1_CLK_ENABLE()            LL_C2_AHB2_GRP1_EnableClock(LL_C2_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_C2GPIOA_CLK_DISABLE()          LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_C2GPIOB_CLK_DISABLE()          LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_C2GPIOC_CLK_DISABLE()          LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_CLK_DISABLE()          LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_C2GPIOE_CLK_DISABLE()          LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_C2GPIOH_CLK_DISABLE()          LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_C2ADC_CLK_DISABLE()            LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_C2AES1_CLK_DISABLE()           LL_C2_AHB2_GRP1_DisableClock(LL_C2_AHB2_GRP1_PERIPH_AES1)
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
  * @brief  Enable or disable the AHB3 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2PKA_CLK_ENABLE()            LL_C2_AHB3_GRP1_EnableClock(LL_C2_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_C2AES2_CLK_ENABLE()           LL_C2_AHB3_GRP1_EnableClock(LL_C2_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_C2RNG_CLK_ENABLE()            LL_C2_AHB3_GRP1_EnableClock(LL_C2_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_C2HSEM_CLK_ENABLE()           LL_C2_AHB3_GRP1_EnableClock(LL_C2_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_C2IPCC_CLK_ENABLE()           LL_C2_AHB3_GRP1_EnableClock(LL_C2_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_C2FLASH_CLK_ENABLE()          LL_C2_AHB3_GRP1_EnableClock(LL_C2_AHB3_GRP1_PERIPH_FLASH)

#define __HAL_RCC_C2PKA_CLK_DISABLE()           LL_C2_AHB3_GRP1_DisableClock(LL_C2_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_C2AES2_CLK_DISABLE()          LL_C2_AHB3_GRP1_DisableClock(LL_C2_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_C2RNG_CLK_DISABLE()           LL_C2_AHB3_GRP1_DisableClock(LL_C2_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_C2HSEM_CLK_DISABLE()          LL_C2_AHB3_GRP1_DisableClock(LL_C2_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_C2IPCC_CLK_DISABLE()          LL_C2_AHB3_GRP1_DisableClock(LL_C2_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_C2FLASH_CLK_DISABLE()         LL_C2_AHB3_GRP1_DisableClock(LL_C2_AHB3_GRP1_PERIPH_FLASH)

/**
  * @}
  */

/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
  * @brief  Enable or disable the APB1 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2RTCAPB_CLK_ENABLE()          LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_C2TIM2_CLK_ENABLE()            LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_C2LCD_CLK_ENABLE()             LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_CLK_ENABLE()            LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_C2I2C1_CLK_ENABLE()            LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_CLK_ENABLE()            LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_CLK_ENABLE()             LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_CLK_ENABLE()             LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_C2LPTIM1_CLK_ENABLE()          LL_C2_APB1_GRP1_EnableClock(LL_C2_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_C2LPTIM2_CLK_ENABLE()          LL_C2_APB1_GRP2_EnableClock(LL_C2_APB1_GRP2_PERIPH_LPTIM2)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_CLK_ENABLE()         LL_C2_APB1_GRP2_EnableClock(LL_C2_APB1_GRP2_PERIPH_LPUART1)
#endif

#define __HAL_RCC_C2RTCAPB_CLK_DISABLE()         LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_C2TIM2_CLK_DISABLE()           LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_C2LCD_CLK_DISABLE()            LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_CLK_DISABLE()           LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_C2I2C1_CLK_DISABLE()           LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_CLK_DISABLE()           LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_CLK_DISABLE()            LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_CLK_DISABLE()            LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_C2LPTIM1_CLK_DISABLE()         LL_C2_APB1_GRP1_DisableClock(LL_C2_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_C2LPTIM2_CLK_DISABLE()         LL_C2_APB1_GRP2_DisableClock(LL_C2_APB1_GRP2_PERIPH_LPTIM2)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_CLK_DISABLE()        LL_C2_APB1_GRP2_DisableClock(LL_C2_APB1_GRP2_PERIPH_LPUART1)
#endif

/**
  * @}
  */

/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
  * @brief  Enable or disable the APB2 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2TIM1_CLK_ENABLE()            LL_C2_APB2_GRP1_EnableClock(LL_C2_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_C2SPI1_CLK_ENABLE()            LL_C2_APB2_GRP1_EnableClock(LL_C2_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_C2USART1_CLK_ENABLE()          LL_C2_APB2_GRP1_EnableClock(LL_C2_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_C2TIM16_CLK_ENABLE()           LL_C2_APB2_GRP1_EnableClock(LL_C2_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_C2TIM17_CLK_ENABLE()           LL_C2_APB2_GRP1_EnableClock(LL_C2_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_CLK_ENABLE()            LL_C2_APB2_GRP1_EnableClock(LL_C2_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_C2TIM1_CLK_DISABLE()           LL_C2_APB2_GRP1_DisableClock(LL_C2_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_C2SPI1_CLK_DISABLE()           LL_C2_APB2_GRP1_DisableClock(LL_C2_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_C2USART1_CLK_DISABLE()         LL_C2_APB2_GRP1_DisableClock(LL_C2_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_C2TIM16_CLK_DISABLE()          LL_C2_APB2_GRP1_DisableClock(LL_C2_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_C2TIM17_CLK_DISABLE()          LL_C2_APB2_GRP1_DisableClock(LL_C2_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_CLK_DISABLE()           LL_C2_APB2_GRP1_DisableClock(LL_C2_APB2_GRP1_PERIPH_SAI1)
#endif

/**
  * @}
  */

/** @defgroup RCC_APB3_Clock_Enable_Disable APB3 Peripheral Clock Enable Disable
  * @brief  Enable or disable the APB3 peripheral clock.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2BLE_CLK_ENABLE()           LL_C2_APB3_GRP1_EnableClock(LL_C2_APB3_GRP1_PERIPH_BLE)
#define __HAL_RCC_C2802_CLK_ENABLE()           LL_C2_APB3_GRP1_EnableClock(LL_C2_APB3_GRP1_PERIPH_802)

#define __HAL_RCC_C2BLE_CLK_DISABLE()          LL_C2_APB3_GRP1_DisableClock(LL_C2_APB3_GRP1_PERIPH_BLE)
#define __HAL_RCC_C2802_CLK_DISABLE()          LL_C2_APB3_GRP1_DisableClock(LL_C2_APB3_GRP1_PERIPH_802)


/**
  * @}
  */

/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the AHB1 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2DMA1_IS_CLK_ENABLED()        LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_IS_CLK_ENABLED()        LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_C2DMAMUX1_IS_CLK_ENABLED()     LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_C2SRAM1_IS_CLK_ENABLED()       LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_SRAM1)
#define __HAL_RCC_C2CRC_IS_CLK_ENABLED()         LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_C2TSC_IS_CLK_ENABLED()         LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_C2DMA1_IS_CLK_DISABLED()       !(LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_DMA1))
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_IS_CLK_DISABLED()       !(LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_DMA2))
#endif
#define __HAL_RCC_C2DMAMUX1_IS_CLK_DISABLED()    !(LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_DMAMUX1))
#define __HAL_RCC_C2SRAM1_IS_CLK_DISABLED()      !(LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_SRAM1))
#define __HAL_RCC_C2CRC_IS_CLK_DISABLED()        !(LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_CRC))
#define __HAL_RCC_C2TSC_IS_CLK_DISABLED()        !(LL_C2_AHB1_GRP1_IsEnabledClock(LL_C2_AHB1_GRP1_PERIPH_TSC))

/**
  * @}
  */

/** @defgroup RCC_AHB2_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the AHB2 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2GPIOA_IS_CLK_ENABLED()       LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_C2GPIOB_IS_CLK_ENABLED()       LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_C2GPIOC_IS_CLK_ENABLED()       LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_IS_CLK_ENABLED()       LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_C2GPIOE_IS_CLK_ENABLED()       LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_C2GPIOH_IS_CLK_ENABLED()       LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_C2ADC_IS_CLK_ENABLED()         LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_C2AES1_IS_CLK_ENABLED()        LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_C2GPIOA_IS_CLK_DISABLED()      !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOA))
#define __HAL_RCC_C2GPIOB_IS_CLK_DISABLED()      !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOB))
#define __HAL_RCC_C2GPIOC_IS_CLK_DISABLED()      !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOC))
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_IS_CLK_DISABLED()      !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOD))
#endif
#define __HAL_RCC_C2GPIOE_IS_CLK_DISABLED()      !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOE))
#define __HAL_RCC_C2GPIOH_IS_CLK_DISABLED()      !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_GPIOH))
#define __HAL_RCC_C2ADC_IS_CLK_DISABLED()        !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_ADC))
#if defined(AES1)
#define __HAL_RCC_C2AES1_IS_CLK_DISABLED()       !(LL_C2_AHB2_GRP1_IsEnabledClock(LL_C2_AHB2_GRP1_PERIPH_AES1))
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB3_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the AHB3 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2PKA_IS_CLK_ENABLED()          LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_C2AES2_IS_CLK_ENABLED()         LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_C2RNG_IS_CLK_ENABLED()          LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_C2HSEM_IS_CLK_ENABLED()         LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_C2IPCC_IS_CLK_ENABLED()         LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_C2FLASH_IS_CLK_ENABLED()        LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_FLASH)

#define __HAL_RCC_C2PKA_IS_CLK_DISABLED()         !(LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_PKA))
#define __HAL_RCC_C2AES2_IS_CLK_DISABLED()        !(LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_AES2))
#define __HAL_RCC_C2RNG_IS_CLK_DISABLED()         !(LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_RNG))
#define __HAL_RCC_C2HSEM_IS_CLK_DISABLED()        !(LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_HSEM))
#define __HAL_RCC_C2IPCC_IS_CLK_DISABLED()        !(LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_IPCC))
#define __HAL_RCC_C2FLASH_IS_CLK_DISABLED()       !(LL_C2_AHB3_GRP1_IsEnabledClock(LL_C2_AHB3_GRP1_PERIPH_FLASH))

/**
  * @}
  */

/** @defgroup RCC_APB1_Clock_Enable_Disable_Status APB1 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the APB1 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2RTCAPB_IS_CLK_ENABLED()         LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_C2TIM2_IS_CLK_ENABLED()           LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_C2LCD_IS_CLK_ENABLED()            LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_IS_CLK_ENABLED()           LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_C2I2C1_IS_CLK_ENABLED()           LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_IS_CLK_ENABLED()           LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_IS_CLK_ENABLED()            LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_IS_CLK_ENABLED()            LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_C2LPTIM1_IS_CLK_ENABLED()         LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_C2LPTIM2_IS_CLK_ENABLED()         LL_C2_APB1_GRP2_IsEnabledClock(LL_C2_APB1_GRP2_PERIPH_LPTIM2)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_IS_CLK_ENABLED()        LL_C2_APB1_GRP2_IsEnabledClock(LL_C2_APB1_GRP2_PERIPH_LPUART1)
#endif

#define __HAL_RCC_C2RTCAPB_IS_CLK_DISABLED()       !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_RTCAPB))
#define __HAL_RCC_C2TIM2_IS_CLK_DISABLED()         !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_TIM2))
#if defined(LCD)
#define __HAL_RCC_C2LCD_IS_CLK_DISABLED()          !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_LCD))
#endif
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_IS_CLK_DISABLED()         !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_SPI2))
#endif
#define __HAL_RCC_C2I2C1_IS_CLK_DISABLED()         !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_I2C1))
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_IS_CLK_DISABLED()         !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_I2C3))
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_IS_CLK_DISABLED()          !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_CRS))
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_IS_CLK_DISABLED()          !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_USB))
#endif
#define __HAL_RCC_C2LPTIM1_IS_CLK_DISABLED()       !(LL_C2_APB1_GRP1_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_LPTIM1))

#define __HAL_RCC_C2LPTIM2_IS_CLK_DISABLED()       !(LL_C2_APB1_GRP2_IsEnabledClock(LL_C2_APB1_GRP2_PERIPH_LPTIM2))
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_IS_CLK_DISABLED()      !(LL_C2_APB1_GRP2_IsEnabledClock(LL_C2_APB1_GRP1_PERIPH_LPTIM1))
#endif

/**
  * @}
  */

/** @defgroup RCC_APB2_Clock_Enable_Disable_Status APB2 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the APB2 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2TIM1_IS_CLK_ENABLED()           LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_C2SPI1_IS_CLK_ENABLED()           LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_C2USART1_IS_CLK_ENABLED()         LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_C2TIM16_IS_CLK_ENABLED()          LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_C2TIM17_IS_CLK_ENABLED()          LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_IS_CLK_ENABLED()           LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_C2TIM1_IS_CLK_DISABLED()          !( LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_TIM1))
#define __HAL_RCC_C2SPI1_IS_CLK_DISABLED()          !( LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_SPI1))
#define __HAL_RCC_C2USART1_IS_CLK_DISABLED()        !( LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_USART1))
#define __HAL_RCC_C2TIM16_IS_CLK_DISABLED()         !( LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_TIM16))
#define __HAL_RCC_C2TIM17_IS_CLK_DISABLED()         !( LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_TIM17))
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_IS_CLK_DISABLED()          !( LL_C2_APB2_GRP1_IsEnabledClock(LL_C2_APB2_GRP1_PERIPH_SAI1))
#endif

/**
  * @}
  */


/** @defgroup RCC_APB3_Clock_Enable_Disable_Status APB3 Peripheral Clock Enabled or Disabled Status
  * @brief  Check whether the APB3 peripheral clock is enabled or not.
  * @note   After reset, the peripheral clock (used for registers read/write access)
  *         is disabled and the application software has to enable this clock before
  *         using it.
  * @{
  */

#define __HAL_RCC_C2BLE_IS_CLK_ENABLED()            LL_C2_APB3_GRP1_IsEnabledClock(LL_C2_APB3_GRP1_PERIPH_BLE)
#define __HAL_RCC_C2802_IS_CLK_ENABLED()            LL_C2_APB3_GRP1_IsEnabledClock(LL_C2_APB3_GRP1_PERIPH_802)

#define __HAL_RCC_C2BLE_IS_CLK_DISABLED()          !(LL_C2_APB3_GRP1_IsEnabledClock(LL_C2_APB3_GRP1_PERIPH_BLE))
#define __HAL_RCC_C2802_IS_CLK_DISABLED()          !(LL_C2_APB3_GRP1_IsEnabledClock(LL_C2_APB3_GRP1_PERIPH_802))

/**
  * @}
  */


/** @defgroup RCC_AHB1_Force_Release_Reset AHB1 Peripheral Force Release Reset
  * @brief  Force or release AHB1 peripheral reset.
  * @{
  */
#define __HAL_RCC_AHB1_FORCE_RESET()           LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_ALL)
#define __HAL_RCC_DMA1_FORCE_RESET()           LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_FORCE_RESET()           LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_FORCE_RESET()        LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_CRC_FORCE_RESET()            LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_FORCE_RESET()            LL_AHB1_GRP1_ForceReset(LL_AHB1_GRP1_PERIPH_TSC)


#define __HAL_RCC_AHB1_RELEASE_RESET()         LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_ALL)
#define __HAL_RCC_DMA1_RELEASE_RESET()         LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_RELEASE_RESET()         LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_RELEASE_RESET()      LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_CRC_RELEASE_RESET()          LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_RELEASE_RESET()          LL_AHB1_GRP1_ReleaseReset(LL_AHB1_GRP1_PERIPH_TSC)


/**
  * @}
  */

/** @defgroup RCC_AHB2_Force_Release_Reset AHB2 Peripheral Force Release Reset
  * @brief  Force or release AHB2 peripheral reset.
  * @{
  */
#define __HAL_RCC_AHB2_FORCE_RESET()           LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_ALL)
#define __HAL_RCC_GPIOA_FORCE_RESET()          LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_FORCE_RESET()          LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_FORCE_RESET()          LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_FORCE_RESET()          LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_FORCE_RESET()          LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_FORCE_RESET()          LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_ADC_FORCE_RESET()            LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_AES1_FORCE_RESET()           LL_AHB2_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_AHB2_RELEASE_RESET()         LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_ALL)
#define __HAL_RCC_GPIOA_RELEASE_RESET()        LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_RELEASE_RESET()        LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_RELEASE_RESET()        LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_RELEASE_RESET()        LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_RELEASE_RESET()        LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_RELEASE_RESET()        LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_ADC_RELEASE_RESET()          LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_AES1_RELEASE_RESET()         LL_AHB2_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_AES1)
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB3_Force_Release_Reset AHB3 Peripheral Force Release Reset
  * @brief  Force or release AHB3 peripheral reset.
  * @{
  */
#define __HAL_RCC_AHB3_FORCE_RESET()           LL_AHB3_GRP1_ForceReset(LL_AHB2_GRP1_PERIPH_ALL)
#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_FORCE_RESET()        LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_FORCE_RESET()            LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_FORCE_RESET()           LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_FORCE_RESET()            LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_HSEM_FORCE_RESET()           LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_IPCC_FORCE_RESET()           LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_FLASH_FORCE_RESET()          LL_AHB3_GRP1_ForceReset(LL_AHB3_GRP1_PERIPH_FLASH)

#define __HAL_RCC_AHB3_RELEASE_RESET()         LL_AHB3_GRP1_ReleaseReset(LL_AHB2_GRP1_PERIPH_ALL)
#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_RELEASE_RESET()      LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_RELEASE_RESET()          LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_RELEASE_RESET()         LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_RELEASE_RESET()          LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_HSEM_RELEASE_RESET()         LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_HSEM)
#define __HAL_RCC_IPCC_RELEASE_RESET()         LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_IPCC)
#define __HAL_RCC_FLASH_RELEASE_RESET()        LL_AHB3_GRP1_ReleaseReset(LL_AHB3_GRP1_PERIPH_FLASH)
/**
  * @}
  */

/** @defgroup RCC_APB1_Force_Release_Reset APB1 Peripheral Force Release Reset
  * @brief  Force or release APB1 peripheral reset.
  * @{
  */

#define __HAL_RCC_APB1L_FORCE_RESET()          LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_ALL)
#define __HAL_RCC_TIM2_FORCE_RESET()           LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_FORCE_RESET()            LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_SPI2_FORCE_RESET()           LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_FORCE_RESET()           LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_FORCE_RESET()           LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_FORCE_RESET()            LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_FORCE_RESET()            LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_FORCE_RESET()         LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_APB1H_FORCE_RESET()          LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_ALL)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_FORCE_RESET()        LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_LPUART1)
#endif
#define __HAL_RCC_LPTIM2_FORCE_RESET()         LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_LPTIM2)

#define __HAL_RCC_APB1_FORCE_RESET() do { \
                                           __HAL_RCC_APB1L_FORCE_RESET();\
                                           __HAL_RCC_APB1H_FORCE_RESET();\
                                        } while(0U)

#define __HAL_RCC_APB1L_RELEASE_RESET()        LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_ALL)
#define __HAL_RCC_TIM2_RELEASE_RESET()         LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_RELEASE_RESET()          LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_LCD)
#endif
#if defined(SPI2)
#define __HAL_RCC_SPI2_RELEASE_RESET()         LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_RELEASE_RESET()         LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_RELEASE_RESET()         LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_RELEASE_RESET()          LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_RELEASE_RESET()          LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_RELEASE_RESET()       LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_LPTIM1)

#define __HAL_RCC_APB1H_RELEASE_RESET()        LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_ALL)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_RELEASE_RESET()      LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_LPUART1)
#endif
#define __HAL_RCC_LPTIM2_RELEASE_RESET()       LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_LPTIM2)

#define __HAL_RCC_APB1_RELEASE_RESET() do { \
                                           __HAL_RCC_APB1L_RELEASE_RESET();\
                                           __HAL_RCC_APB1H_RELEASE_RESET();\
                                        } while(0U)
/**
  * @}
  */

/** @defgroup RCC_APB2_Force_Release_Reset APB2 Peripheral Force Release Reset
  * @brief  Force or release APB2 peripheral reset.
  * @{
  */
#define __HAL_RCC_APB2_FORCE_RESET()           LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_ALL)
#define __HAL_RCC_TIM1_FORCE_RESET()           LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_FORCE_RESET()           LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_FORCE_RESET()         LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_FORCE_RESET()          LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_FORCE_RESET()          LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_FORCE_RESET()           LL_APB2_GRP1_ForceReset(LL_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_APB2_RELEASE_RESET()         LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_ALL)
#define __HAL_RCC_TIM1_RELEASE_RESET()         LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_RELEASE_RESET()         LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_RELEASE_RESET()       LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_RELEASE_RESET()        LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_RELEASE_RESET()        LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_RELEASE_RESET()         LL_APB2_GRP1_ReleaseReset(LL_APB2_GRP1_PERIPH_SAI1)
#endif
/**
  * @}
  */

/** @defgroup RCC_APB3_Force_Release_Reset APB3 Peripheral Force Release Reset
  * @brief  Force or release APB3 peripheral reset.
  * @{
  */
#define __HAL_RCC_APB3_FORCE_RESET()           LL_APB3_GRP1_ForceReset(LL_APB3_GRP1_PERIPH_ALL)
#define __HAL_RCC_RF_FORCE_RESET()             LL_APB3_GRP1_ForceReset(LL_APB3_GRP1_PERIPH_RF)

#define __HAL_RCC_APB3_RELEASE_RESET()         LL_APB3_GRP1_ReleaseReset(LL_APB3_GRP1_PERIPH_ALL)
#define __HAL_RCC_RF_RELEASE_RESET()           LL_APB3_GRP1_ReleaseReset(LL_APB3_GRP1_PERIPH_RF)

/**
  * @}
  */

/** @defgroup RCC_AHB1_Clock_Sleep_Enable_Disable AHB1 Peripheral Clock Sleep Enable Disable
  * @brief  Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_DMA1_CLK_SLEEP_ENABLE()       LL_AHB1_GRP1_EnableClockSleep(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_CLK_SLEEP_ENABLE()       LL_AHB1_GRP1_EnableClockSleep(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_CLK_SLEEP_ENABLE()    LL_AHB1_GRP1_EnableClockSleep(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE()      LL_AHB1_GRP1_EnableClockSleep(LL_AHB1_GRP1_PERIPH_SRAM1)
#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE()        LL_AHB1_GRP1_EnableClockSleep(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_CLK_SLEEP_ENABLE()        LL_AHB1_GRP1_EnableClockSleep(LL_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_DMA1_CLK_SLEEP_DISABLE()      LL_AHB1_GRP1_DisableClockSleep(LL_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_DMA2_CLK_SLEEP_DISABLE()      LL_AHB1_GRP1_DisableClockSleep(LL_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_DMAMUX1_CLK_SLEEP_DISABLE()   LL_AHB1_GRP1_DisableClockSleep(LL_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE()     LL_AHB1_GRP1_DisableClockSleep(LL_AHB1_GRP1_PERIPH_SRAM1)
#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE()       LL_AHB1_GRP1_DisableClockSleep(LL_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_TSC_CLK_SLEEP_DISABLE()       LL_AHB1_GRP1_DisableClockSleep(LL_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_C2DMA1_CLK_SLEEP_ENABLE()     LL_C2_AHB1_GRP1_EnableClockSleep(LL_C2_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_CLK_SLEEP_ENABLE()     LL_C2_AHB1_GRP1_EnableClockSleep(LL_C2_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_C2DMAMUX1_CLK_SLEEP_ENABLE()  LL_C2_AHB1_GRP1_EnableClockSleep(LL_C2_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_C2SRAM1_CLK_SLEEP_ENABLE()    LL_C2_AHB1_GRP1_EnableClockSleep(LL_C2_AHB1_GRP1_PERIPH_SRAM1)
#define __HAL_RCC_C2CRC_CLK_SLEEP_ENABLE()      LL_C2_AHB1_GRP1_EnableClockSleep(LL_C2_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_C2TSC_CLK_SLEEP_ENABLE()      LL_C2_AHB1_GRP1_EnableClockSleep(LL_C2_AHB1_GRP1_PERIPH_TSC)

#define __HAL_RCC_C2DMA1_CLK_SLEEP_DISABLE()    LL_C2_AHB1_GRP1_DisableClockSleep(LL_C2_AHB1_GRP1_PERIPH_DMA1)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_CLK_SLEEP_DISABLE()    LL_C2_AHB1_GRP1_DisableClockSleep(LL_C2_AHB1_GRP1_PERIPH_DMA2)
#endif
#define __HAL_RCC_C2DMAMUX1_CLK_SLEEP_DISABLE() LL_C2_AHB1_GRP1_DisableClockSleep(LL_C2_AHB1_GRP1_PERIPH_DMAMUX1)
#define __HAL_RCC_C2SRAM1_CLK_SLEEP_DISABLE()   LL_C2_AHB1_GRP1_DisableClockSleep(LL_C2_AHB1_GRP1_PERIPH_SRAM1)

#define __HAL_RCC_C2CRC_CLK_SLEEP_DISABLE()     LL_C2_AHB1_GRP1_DisableClockSleep(LL_C2_AHB1_GRP1_PERIPH_CRC)
#define __HAL_RCC_C2TSC_CLK_SLEEP_DISABLE()     LL_C2_AHB1_GRP1_DisableClockSleep(LL_C2_AHB1_GRP1_PERIPH_TSC)

/**
  * @}
  */

/** @defgroup RCC_AHB2_Clock_Sleep_Enable_Disable AHB2 Peripheral Clock Sleep Enable Disable
  * @brief  Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_GPIOA_CLK_SLEEP_ENABLE()     LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_CLK_SLEEP_ENABLE()     LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_CLK_SLEEP_ENABLE()     LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE()     LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE()     LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_CLK_SLEEP_ENABLE()     LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_ADC_CLK_SLEEP_ENABLE()       LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_AES1_CLK_SLEEP_ENABLE()      LL_AHB2_GRP1_EnableClockSleep(LL_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_GPIOA_CLK_SLEEP_DISABLE()    LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_GPIOB_CLK_SLEEP_DISABLE()    LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_GPIOC_CLK_SLEEP_DISABLE()    LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE()    LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE()    LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_GPIOH_CLK_SLEEP_DISABLE()    LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_ADC_CLK_SLEEP_DISABLE()      LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_AES1_CLK_SLEEP_DISABLE()     LL_AHB2_GRP1_DisableClockSleep(LL_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_C2GPIOA_CLK_SLEEP_ENABLE()   LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_C2GPIOB_CLK_SLEEP_ENABLE()   LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_C2GPIOC_CLK_SLEEP_ENABLE()   LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_CLK_SLEEP_ENABLE()   LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_C2GPIOE_CLK_SLEEP_ENABLE()   LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_C2GPIOH_CLK_SLEEP_ENABLE()   LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_C2ADC_CLK_SLEEP_ENABLE()     LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_C2AES1_CLK_SLEEP_ENABLE()    LL_C2_AHB2_GRP1_EnableClockSleep(LL_C2_AHB2_GRP1_PERIPH_AES1)
#endif

#define __HAL_RCC_C2GPIOA_CLK_SLEEP_DISABLE()  LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOA)
#define __HAL_RCC_C2GPIOB_CLK_SLEEP_DISABLE()  LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOB)
#define __HAL_RCC_C2GPIOC_CLK_SLEEP_DISABLE()  LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOC)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_CLK_SLEEP_DISABLE()  LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOD)
#endif
#define __HAL_RCC_C2GPIOE_CLK_SLEEP_DISABLE()  LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOE)
#define __HAL_RCC_C2GPIOH_CLK_SLEEP_DISABLE()  LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_GPIOH)
#define __HAL_RCC_C2ADC_CLK_SLEEP_DISABLE()    LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_ADC)
#if defined(AES1)
#define __HAL_RCC_C2AES1_CLK_SLEEP_DISABLE()   LL_C2_AHB2_GRP1_DisableClockSleep(LL_C2_AHB2_GRP1_PERIPH_AES1)
#endif

/**
  * @}
  */

/** @defgroup RCC_AHB3_Clock_Sleep_Enable_Disable AHB3 Peripheral Clock Sleep Enable Disable
  * @brief  Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_CLK_SLEEP_ENABLE()   LL_AHB3_GRP1_EnableClockSleep(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_CLK_SLEEP_ENABLE()       LL_AHB3_GRP1_EnableClockSleep(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_CLK_SLEEP_ENABLE()      LL_AHB3_GRP1_EnableClockSleep(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE()       LL_AHB3_GRP1_EnableClockSleep(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE()     LL_AHB3_GRP1_EnableClockSleep(LL_AHB3_GRP1_PERIPH_SRAM2)
#define __HAL_RCC_FLASH_CLK_SLEEP_ENABLE()     LL_AHB3_GRP1_EnableClockSleep(LL_AHB3_GRP1_PERIPH_FLASH)

#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_CLK_SLEEP_DISABLE()  LL_AHB3_GRP1_DisableClockSleep(LL_AHB3_GRP1_PERIPH_QUADSPI)
#endif
#define __HAL_RCC_PKA_CLK_SLEEP_DISABLE()      LL_AHB3_GRP1_DisableClockSleep(LL_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_AES2_CLK_SLEEP_DISABLE()     LL_AHB3_GRP1_DisableClockSleep(LL_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE()      LL_AHB3_GRP1_DisableClockSleep(LL_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE()    LL_AHB3_GRP1_DisableClockSleep(LL_AHB3_GRP1_PERIPH_SRAM2)
#define __HAL_RCC_FLASH_CLK_SLEEP_DISABLE()    LL_AHB3_GRP1_DisableClockSleep(LL_AHB3_GRP1_PERIPH_FLASH)

#define __HAL_RCC_C2PKA_CLK_SLEEP_ENABLE()     LL_C2_AHB3_GRP1_EnableClockSleep(LL_C2_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_C2AES2_CLK_SLEEP_ENABLE()    LL_C2_AHB3_GRP1_EnableClockSleep(LL_C2_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_C2RNG_CLK_SLEEP_ENABLE()     LL_C2_AHB3_GRP1_EnableClockSleep(LL_C2_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_C2SRAM2_CLK_SLEEP_ENABLE()   LL_C2_AHB3_GRP1_EnableClockSleep(LL_C2_AHB3_GRP1_PERIPH_SRAM2)
#define __HAL_RCC_C2FLASH_CLK_SLEEP_ENABLE()   LL_C2_AHB3_GRP1_EnableClockSleep(LL_C2_AHB3_GRP1_PERIPH_FLASH)

#define __HAL_RCC_C2PKA_CLK_SLEEP_DISABLE()    LL_C2_AHB3_GRP1_DisableClockSleep(LL_C2_AHB3_GRP1_PERIPH_PKA)
#define __HAL_RCC_C2AES2_CLK_SLEEP_DISABLE()   LL_C2_AHB3_GRP1_DisableClockSleep(LL_C2_AHB3_GRP1_PERIPH_AES2)
#define __HAL_RCC_C2RNG_CLK_SLEEP_DISABLE()    LL_C2_AHB3_GRP1_DisableClockSleep(LL_C2_AHB3_GRP1_PERIPH_RNG)
#define __HAL_RCC_C2SRAM2_CLK_SLEEP_DISABLE()  LL_C2_AHB3_GRP1_DisableClockSleep(LL_C2_AHB3_GRP1_PERIPH_SRAM2)
#define __HAL_RCC_C2FLASH_CLK_SLEEP_DISABLE()  LL_C2_AHB3_GRP1_DisableClockSleep(LL_C2_AHB3_GRP1_PERIPH_FLASH)

/**
  * @}
  */

/** @defgroup RCC_APB1_Clock_Sleep_Enable_Disable APB1 Peripheral Clock Sleep Enable Disable
  * @brief  Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE()           LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_CLK_SLEEP_ENABLE()            LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_LCD)
#endif
#define __HAL_RCC_RTCAPB_CLK_SLEEP_ENABLE()         LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE()           LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_WWDG)
#if defined(SPI2)
#define __HAL_RCC_SPI2_CLK_SLEEP_ENABLE()           LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_CLK_SLEEP_ENABLE()           LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE()           LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_CLK_SLEEP_ENABLE()            LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_CLK_SLEEP_ENABLE()            LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_CLK_SLEEP_ENABLE()         LL_APB1_GRP1_EnableClockSleep(LL_APB1_GRP1_PERIPH_LPTIM1)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_CLK_SLEEP_ENABLE()        LL_APB1_GRP2_EnableClockSleep(LL_APB1_GRP2_PERIPH_LPUART1)
#endif
#define __HAL_RCC_LPTIM2_CLK_SLEEP_ENABLE()         LL_APB1_GRP2_EnableClockSleep(LL_APB1_GRP2_PERIPH_LPTIM2)

#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE()          LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_LCD_CLK_SLEEP_DISABLE()           LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_LCD)
#endif
#define __HAL_RCC_RTCAPB_CLK_SLEEP_DISABLE()        LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_RTCAPB)
#define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE()          LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_WWDG)
#if defined(SPI2)
#define __HAL_RCC_SPI2_CLK_SLEEP_DISABLE()          LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_I2C1_CLK_SLEEP_DISABLE()          LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE()          LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_CLK_SLEEP_DISABLE()           LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_USB_CLK_SLEEP_DISABLE()           LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_LPTIM1_CLK_SLEEP_DISABLE()        LL_APB1_GRP1_DisableClockSleep(LL_APB1_GRP1_PERIPH_LPTIM1)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_CLK_SLEEP_DISABLE()       LL_APB1_GRP2_DisableClockSleep(LL_APB1_GRP2_PERIPH_LPUART1)
#endif
#define __HAL_RCC_LPTIM2_CLK_SLEEP_DISABLE()        LL_APB1_GRP2_DisableClockSleep(LL_APB1_GRP2_PERIPH_LPTIM2)

#define __HAL_RCC_C2TIM2_CLK_SLEEP_ENABLE()         LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_C2LCD_CLK_SLEEP_ENABLE()          LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_LCD)
#endif
#define __HAL_RCC_C2RTCAPB_CLK_SLEEP_ENABLE()       LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_RTCAPB)
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_CLK_SLEEP_ENABLE()         LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_C2I2C1_CLK_SLEEP_ENABLE()         LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_CLK_SLEEP_ENABLE()         LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_CLK_SLEEP_ENABLE()          LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_CLK_SLEEP_ENABLE()          LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_C2LPTIM1_CLK_SLEEP_ENABLE()       LL_C2_APB1_GRP1_EnableClockSleep(LL_C2_APB1_GRP1_PERIPH_LPTIM1)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_CLK_SLEEP_ENABLE()      LL_C2_APB1_GRP2_EnableClockSleep(LL_C2_APB1_GRP2_PERIPH_LPUART1)
#endif
#define __HAL_RCC_C2LPTIM2_CLK_SLEEP_ENABLE()       LL_C2_APB1_GRP2_EnableClockSleep(LL_C2_APB1_GRP2_PERIPH_LPTIM2)

#define __HAL_RCC_C2TIM2_CLK_SLEEP_DISABLE()        LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_TIM2)
#if defined(LCD)
#define __HAL_RCC_C2LCD_CLK_SLEEP_DISABLE()         LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_LCD)
#endif
#define __HAL_RCC_C2RTCAPB_CLK_SLEEP_DISABLE()      LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_RTCAPB)
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_CLK_SLEEP_DISABLE()        LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_SPI2)
#endif
#define __HAL_RCC_C2I2C1_CLK_SLEEP_DISABLE()        LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_I2C1)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_CLK_SLEEP_DISABLE()        LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_I2C3)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_CLK_SLEEP_DISABLE()         LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_CRS)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_CLK_SLEEP_DISABLE()         LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_USB)
#endif
#define __HAL_RCC_C2LPTIM1_CLK_SLEEP_DISABLE()      LL_C2_APB1_GRP1_DisableClockSleep(LL_C2_APB1_GRP1_PERIPH_LPTIM1)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_CLK_SLEEP_DISABLE()     LL_C2_APB1_GRP2_DisableClockSleep(LL_C2_APB1_GRP2_PERIPH_LPUART1)
#endif
#define __HAL_RCC_C2LPTIM2_CLK_SLEEP_DISABLE()      LL_C2_APB1_GRP2_DisableClockSleep(LL_C2_APB1_GRP2_PERIPH_LPTIM2)

/**
  * @}
  */

/** @defgroup RCC_APB2_Clock_Sleep_Enable_Disable APB2 Peripheral Clock Sleep Enable Disable
  * @brief  Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_TIM1_CLK_SLEEP_ENABLE()           LL_APB2_GRP1_EnableClockSleep(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_CLK_SLEEP_ENABLE()           LL_APB2_GRP1_EnableClockSleep(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_CLK_SLEEP_ENABLE()         LL_APB2_GRP1_EnableClockSleep(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_CLK_SLEEP_ENABLE()          LL_APB2_GRP1_EnableClockSleep(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_CLK_SLEEP_ENABLE()          LL_APB2_GRP1_EnableClockSleep(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE()           LL_APB2_GRP1_EnableClockSleep(LL_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_TIM1_CLK_SLEEP_DISABLE()          LL_APB2_GRP1_DisableClockSleep(LL_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_SPI1_CLK_SLEEP_DISABLE()          LL_APB2_GRP1_DisableClockSleep(LL_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_USART1_CLK_SLEEP_DISABLE()        LL_APB2_GRP1_DisableClockSleep(LL_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_TIM16_CLK_SLEEP_DISABLE()         LL_APB2_GRP1_DisableClockSleep(LL_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_TIM17_CLK_SLEEP_DISABLE()         LL_APB2_GRP1_DisableClockSleep(LL_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE()          LL_APB2_GRP1_DisableClockSleep(LL_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_C2TIM1_CLK_SLEEP_ENABLE()         LL_C2_APB2_GRP1_EnableClockSleep(LL_C2_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_C2SPI1_CLK_SLEEP_ENABLE()         LL_C2_APB2_GRP1_EnableClockSleep(LL_C2_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_C2USART1_CLK_SLEEP_ENABLE()       LL_C2_APB2_GRP1_EnableClockSleep(LL_C2_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_C2TIM16_CLK_SLEEP_ENABLE()        LL_C2_APB2_GRP1_EnableClockSleep(LL_C2_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_C2TIM17_CLK_SLEEP_ENABLE()        LL_C2_APB2_GRP1_EnableClockSleep(LL_C2_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_CLK_SLEEP_ENABLE()         LL_C2_APB2_GRP1_EnableClockSleep(LL_C2_APB2_GRP1_PERIPH_SAI1)
#endif

#define __HAL_RCC_C2TIM1_CLK_SLEEP_DISABLE()        LL_C2_APB2_GRP1_DisableClockSleep(LL_C2_APB2_GRP1_PERIPH_TIM1)
#define __HAL_RCC_C2SPI1_CLK_SLEEP_DISABLE()        LL_C2_APB2_GRP1_DisableClockSleep(LL_C2_APB2_GRP1_PERIPH_SPI1)
#define __HAL_RCC_C2USART1_CLK_SLEEP_DISABLE()      LL_C2_APB2_GRP1_DisableClockSleep(LL_C2_APB2_GRP1_PERIPH_USART1)
#define __HAL_RCC_C2TIM16_CLK_SLEEP_DISABLE()       LL_C2_APB2_GRP1_DisableClockSleep(LL_C2_APB2_GRP1_PERIPH_TIM16)
#define __HAL_RCC_C2TIM17_CLK_SLEEP_DISABLE()       LL_C2_APB2_GRP1_DisableClockSleep(LL_C2_APB2_GRP1_PERIPH_TIM17)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_CLK_SLEEP_DISABLE()        LL_C2_APB2_GRP1_DisableClockSleep(LL_C2_APB2_GRP1_PERIPH_SAI1)
#endif
/**
  * @}
  */

/** @defgroup RCC_AHB1_Clock_Sleep_Enable_Disable_Status AHB1 Peripheral Clock Sleep Enabled or Disabled Status
  * @brief  Check whether the AHB1 peripheral clock during Low Power (Sleep) mode is enabled or not.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_DMA1_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) != RESET)
#if defined(DMA2)
#define __HAL_RCC_DMA2_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) != RESET)
#endif
#define __HAL_RCC_DMAMUX1_IS_CLK_SLEEP_ENABLED()    (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMAMUX1SMEN) != RESET)
#define __HAL_RCC_SRAM1_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) != RESET)
#define __HAL_RCC_CRC_IS_CLK_SLEEP_ENABLED()        (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) != RESET)
#define __HAL_RCC_TSC_IS_CLK_SLEEP_ENABLED()        (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) != RESET)

#define __HAL_RCC_DMA1_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) == RESET)
#if defined(DMA2)
#define __HAL_RCC_DMA2_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) == RESET)
#endif
#define __HAL_RCC_DMAMUX1_IS_CLK_SLEEP_DISABLED()   (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMAMUX1SMEN) == RESET)
#define __HAL_RCC_SRAM1_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) == RESET)
#define __HAL_RCC_CRC_IS_CLK_SLEEP_DISABLED()       (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) == RESET)
#define __HAL_RCC_TSC_IS_CLK_SLEEP_DISABLED()       (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) == RESET)

#define __HAL_RCC_C2DMA1_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_DMA1SMEN) != RESET)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_DMA2SMEN) != RESET)
#endif
#define __HAL_RCC_C2DMAMUX1_IS_CLK_SLEEP_ENABLED()  (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_DMAMUX1SMEN) != RESET)
#define __HAL_RCC_C2SRAM1_IS_CLK_SLEEP_ENABLED()    (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_SRAM1SMEN) != RESET)
#define __HAL_RCC_C2CRC_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_CRCSMEN) != RESET)
#define __HAL_RCC_C2TSC_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_TSCSMEN) != RESET)

#define __HAL_RCC_C2DMA1_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_DMA1SMEN) == RESET)
#if defined(DMA2)
#define __HAL_RCC_C2DMA2_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_DMA2SMEN) == RESET)
#endif
#define __HAL_RCC_C2DMAMUX1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_DMAMUX1SMEN) == RESET)
#define __HAL_RCC_C2SRAM1_IS_CLK_SLEEP_DISABLED()   (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_SRAM1SMEN) == RESET)
#define __HAL_RCC_C2CRC_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_CRCSMEN) == RESET)
#define __HAL_RCC_C2TSC_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->C2AHB1SMENR, RCC_C2AHB1SMENR_TSCSMEN) == RESET)
/**
  * @}
  */

/** @defgroup RCC_AHB2_Clock_Sleep_Enable_Disable_Status AHB2 Peripheral Clock Sleep Enabled or Disabled Status
  * @brief  Check whether the AHB2 peripheral clock during Low Power (Sleep) mode is enabled or not.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_GPIOA_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) != RESET)
#define __HAL_RCC_GPIOB_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) != RESET)
#define __HAL_RCC_GPIOC_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) != RESET)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) != RESET)
#endif
#define __HAL_RCC_GPIOE_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) != RESET)
#define __HAL_RCC_GPIOH_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) != RESET)
#define __HAL_RCC_ADC_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN)   != RESET)
#if defined(AES1)
#define __HAL_RCC_AES1_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AES1SMEN) != RESET)
#endif

#define __HAL_RCC_GPIOA_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) == RESET)
#define __HAL_RCC_GPIOB_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) == RESET)
#define __HAL_RCC_GPIOC_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) == RESET)
#if defined(GPIOD)
#define __HAL_RCC_GPIOD_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) == RESET)
#endif
#define __HAL_RCC_GPIOE_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) == RESET)
#define __HAL_RCC_GPIOH_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) == RESET)
#define __HAL_RCC_ADC_IS_CLK_SLEEP_DISABLED()       (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN)   == RESET)
#if defined(AES1)
#define __HAL_RCC_AES1_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AES1SMEN) == RESET)
#endif

#define __HAL_RCC_C2GPIOA_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOASMEN) != RESET)
#define __HAL_RCC_C2GPIOB_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOBSMEN) != RESET)
#define __HAL_RCC_C2GPIOC_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOCSMEN) != RESET)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIODSMEN) != RESET)
#endif
#define __HAL_RCC_C2GPIOE_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOESMEN) != RESET)
#define __HAL_RCC_C2GPIOH_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOHSMEN) != RESET)
#define __HAL_RCC_C2ADC_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_ADCSMEN)   != RESET)
#if defined(AES1)
#define __HAL_RCC_C2AES1_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_AES1SMEN) != RESET)
#endif

#define __HAL_RCC_C2GPIOA_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOASMEN) == RESET)
#define __HAL_RCC_C2GPIOB_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOBSMEN) == RESET)
#define __HAL_RCC_C2GPIOC_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOCSMEN) == RESET)
#if defined(GPIOD)
#define __HAL_RCC_C2GPIOD_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIODSMEN) == RESET)
#endif
#define __HAL_RCC_C2GPIOE_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOESMEN) == RESET)
#define __HAL_RCC_C2GPIOH_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_GPIOHSMEN) == RESET)
#define __HAL_RCC_C2ADC_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_ADCSMEN)   == RESET)
#if defined(AES1)
#define __HAL_RCC_C2AES1_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->C2AHB2SMENR, RCC_C2AHB2SMENR_AES1SMEN) == RESET)
#endif
/**
  * @}
  */

/** @defgroup RCC_AHB3_Clock_Sleep_Enable_Disable_Status AHB3 Peripheral Clock Sleep Enabled or Disabled Status
  * @brief  Check whether the AHB3 peripheral clock during Low Power (Sleep) mode is enabled or not.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_IS_CLK_SLEEP_ENABLED()   (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QUADSPISMEN) != RESET)
#endif
#define __HAL_RCC_PKA_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_PKASMEN) != RESET)
#define __HAL_RCC_AES2_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_AES2SMEN) != RESET)
#define __HAL_RCC_RNG_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_RNGSMEN) != RESET)
#define __HAL_RCC_SRAM2_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_SRAM2SMEN) != RESET)
#define __HAL_RCC_FLASH_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FLASHSMEN) != RESET)

#if defined(QUADSPI)
#define __HAL_RCC_QUADSPI_IS_CLK_SLEEP_DISABLED()  (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QUADSPISMEN) == RESET)
#endif
#define __HAL_RCC_PKA_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_PKASMEN) == RESET)
#define __HAL_RCC_AES2_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_AES2SMEN) == RESET)
#define __HAL_RCC_RNG_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_RNGSMEN) == RESET)
#define __HAL_RCC_SRAM2_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_SRAM2SMEN) == RESET)
#define __HAL_RCC_FLASH_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FLASHSMEN) == RESET)

#define __HAL_RCC_C2PKA_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_PKASMEN) != RESET)
#define __HAL_RCC_C2AES2_IS_CLK_SLEEP_ENABLED()      (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_AES2SMEN) != RESET)
#define __HAL_RCC_C2RNG_IS_CLK_SLEEP_ENABLED()       (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_RNGSMEN) != RESET)
#define __HAL_RCC_C2SRAM2_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_SRAM2SMEN) != RESET)
#define __HAL_RCC_C2FLASH_IS_CLK_SLEEP_ENABLED()     (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_FLASHSMEN) != RESET)

#define __HAL_RCC_C2PKA_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_PKASMEN) == RESET)
#define __HAL_RCC_C2AES2_IS_CLK_SLEEP_DISABLED()     (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_AES2SMEN) == RESET)
#define __HAL_RCC_C2RNG_IS_CLK_SLEEP_DISABLED()      (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_RNGSMEN) == RESET)
#define __HAL_RCC_C2SRAM2_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_SRAM2SMEN) == RESET)
#define __HAL_RCC_C2FLASH_IS_CLK_SLEEP_DISABLED()    (READ_BIT(RCC->C2AHB3SMENR, RCC_C2AHB3SMENR_FLASHSMEN) == RESET)

/**
  * @}
  */

/** @defgroup RCC_APB1_Clock_Sleep_Enable_Disable_Status APB1 Peripheral Clock Sleep Enabled or Disabled Status
  * @brief  Check whether the APB1 peripheral clock during Low Power (Sleep) mode is enabled or not.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_TIM2_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) != RESET)
#if defined(LCD)
#define __HAL_RCC_LCD_IS_CLK_SLEEP_ENABLED()            (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN)  != RESET)
#endif
#define __HAL_RCC_RTCAPB_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_RTCAPBSMEN)  != RESET)
#define __HAL_RCC_WWDG_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN)  != RESET)
#if defined(SPI2)
#define __HAL_RCC_SPI2_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) != RESET)
#endif
#define __HAL_RCC_I2C1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) != RESET)
#if defined(I2C3)
#define __HAL_RCC_I2C3_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) != RESET)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_IS_CLK_SLEEP_ENABLED()            (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CRSSMEN)  != RESET)
#endif
#if defined(USB)
#define __HAL_RCC_USB_IS_CLK_SLEEP_ENABLED()            (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USBSMEN)  != RESET)
#endif
#define __HAL_RCC_LPTIM1_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) != RESET)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_IS_CLK_SLEEP_ENABLED()        (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) != RESET)
#endif
#define __HAL_RCC_LPTIM2_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) != RESET)

#define __HAL_RCC_TIM2_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) == RESET)
#if defined(LCD)
#define __HAL_RCC_LCD_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN)  == RESET)
#endif
#define __HAL_RCC_RTCAPB_IS_CLK_SLEEP_DISABLED()        (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_RTCAPBSMEN)  == RESET)
#define __HAL_RCC_WWDG_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN)  == RESET)
#if defined(SPI2)
#define __HAL_RCC_SPI2_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) == RESET)
#endif
#define __HAL_RCC_I2C1_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) == RESET)
#if defined(I2C3)
#define __HAL_RCC_I2C3_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) == RESET)
#endif
#if defined(CRS)
#define __HAL_RCC_CRS_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CRSSMEN)  == RESET)
#endif
#if defined(USB)
#define __HAL_RCC_USB_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USBSMEN)  == RESET)
#endif
#define __HAL_RCC_LPTIM1_IS_CLK_SLEEP_DISABLED()        (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) == RESET)
#if defined(LPUART1)
#define __HAL_RCC_LPUART1_IS_CLK_SLEEP_DISABLED()       (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) == RESET)
#endif
#define __HAL_RCC_LPTIM2_IS_CLK_SLEEP_DISABLED()        (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) == RESET)

#define __HAL_RCC_C2TIM2_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_TIM2SMEN) != RESET)
#if defined(LCD)
#define __HAL_RCC_C2LCD_IS_CLK_SLEEP_ENABLED()            (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_LCDSMEN)  != RESET)
#endif
#define __HAL_RCC_C2RTCAPB_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_RTCAPBSMEN)  != RESET)
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_SPI2SMEN) != RESET)
#endif
#define __HAL_RCC_C2I2C1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_I2C1SMEN) != RESET)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_I2C3SMEN) != RESET)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_IS_CLK_SLEEP_ENABLED()            (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_CRSSMEN)  != RESET)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_IS_CLK_SLEEP_ENABLED()            (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_USBSMEN)  != RESET)
#endif
#define __HAL_RCC_C2LPTIM1_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_LPTIM1SMEN) != RESET)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_IS_CLK_SLEEP_ENABLED()        (READ_BIT(RCC->C2APB1SMENR2, RCC_C2APB1SMENR2_LPUART1SMEN) != RESET)
#endif
#define __HAL_RCC_C2LPTIM2_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->C2APB1SMENR2, RCC_C2APB1SMENR2_LPTIM2SMEN) != RESET)

#define __HAL_RCC_C2TIM2_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_TIM2SMEN) == RESET)
#if defined(LCD)
#define __HAL_RCC_C2LCD_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_LCDSMEN)  == RESET)
#endif
#define __HAL_RCC_C2RTCAPB_IS_CLK_SLEEP_DISABLED()        (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_RTCAPBSMEN)  == RESET)
#if defined(SPI2)
#define __HAL_RCC_C2SPI2_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_SPI2SMEN) == RESET)
#endif
#define __HAL_RCC_C2I2C1_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_I2C1SMEN) == RESET)
#if defined(I2C3)
#define __HAL_RCC_C2I2C3_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_I2C3SMEN) == RESET)
#endif
#if defined(CRS)
#define __HAL_RCC_C2CRS_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_CRSSMEN)  == RESET)
#endif
#if defined(USB)
#define __HAL_RCC_C2USB_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_USBSMEN)  == RESET)
#endif
#define __HAL_RCC_C2LPTIM1_IS_CLK_SLEEP_DISABLED()        (READ_BIT(RCC->C2APB1SMENR1, RCC_C2APB1SMENR1_LPTIM1SMEN) == RESET)
#if defined(LPUART1)
#define __HAL_RCC_C2LPUART1_IS_CLK_SLEEP_DISABLED()       (READ_BIT(RCC->C2APB1SMENR2, RCC_C2APB1SMENR2_LPUART1SMEN) == RESET)
#endif
#define __HAL_RCC_C2LPTIM2_IS_CLK_SLEEP_DISABLED()        (READ_BIT(RCC->C2APB1SMENR2, RCC_C2APB1SMENR2_LPTIM2SMEN) == RESET)
/**
  * @}
  */

/** @defgroup RCC_APB2_Clock_Sleep_Enable_Disable_Status APB2 Peripheral Clock Sleep Enabled or Disabled Status
  * @brief  Check whether the APB2 peripheral clock during Low Power (Sleep) mode is enabled or not.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_TIM1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) != RESET)
#define __HAL_RCC_SPI1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) != RESET)
#define __HAL_RCC_USART1_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) != RESET)
#define __HAL_RCC_TIM16_IS_CLK_SLEEP_ENABLED()          (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) != RESET)
#define __HAL_RCC_TIM17_IS_CLK_SLEEP_ENABLED()          (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) != RESET)
#if defined(SAI1)
#define __HAL_RCC_SAI1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) != RESET)
#endif

#define __HAL_RCC_TIM1_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) == RESET)
#define __HAL_RCC_SPI1_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) == RESET)
#define __HAL_RCC_USART1_IS_CLK_SLEEP_DISABLED()         (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) == RESET)
#define __HAL_RCC_TIM16_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) == RESET)
#define __HAL_RCC_TIM17_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) == RESET)
#if defined(SAI1)
#define __HAL_RCC_SAI1_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) == RESET)
#endif

#define __HAL_RCC_C2TIM1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_TIM1SMEN) != RESET)
#define __HAL_RCC_C2SPI1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_SPI1SMEN) != RESET)
#define __HAL_RCC_C2USART1_IS_CLK_SLEEP_ENABLED()         (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_USART1SMEN) != RESET)
#define __HAL_RCC_C2TIM16_IS_CLK_SLEEP_ENABLED()          (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_TIM16SMEN) != RESET)
#define __HAL_RCC_C2TIM17_IS_CLK_SLEEP_ENABLED()          (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_TIM17SMEN) != RESET)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_SAI1SMEN) != RESET)
#endif

#define __HAL_RCC_C2TIM1_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_TIM1SMEN) == RESET)
#define __HAL_RCC_C2SPI1_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_SPI1SMEN) == RESET)
#define __HAL_RCC_C2USART1_IS_CLK_SLEEP_DISABLED()         (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_USART1SMEN) == RESET)
#define __HAL_RCC_C2TIM16_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_TIM16SMEN) == RESET)
#define __HAL_RCC_C2TIM17_IS_CLK_SLEEP_DISABLED()          (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_TIM17SMEN) == RESET)
#if defined(SAI1)
#define __HAL_RCC_C2SAI1_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB2SMENR, RCC_C2APB2SMENR_SAI1SMEN) == RESET)
#endif
/**
  * @}
  */

/** @defgroup RCC_C2APB3_Clock_Sleep_Enable_Disable APB3 Peripheral Clock Sleep Enable Disable
  * @brief  Enable or disable the APB3 peripheral clock during Low Power (Sleep) mode.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_C2BLE_CLK_SLEEP_ENABLE()          LL_C2_APB3_GRP1_EnableClockSleep(LL_C2_APB3_GRP1_PERIPH_BLE)
#define __HAL_RCC_C2802_CLK_SLEEP_ENABLE()          LL_C2_APB3_GRP1_EnableClockSleep(LL_C2_APB3_GRP1_PERIPH_802)

#define __HAL_RCC_C2BLE_CLK_SLEEP_DISABLE()         LL_C2_APB3_GRP1_DisableClockSleep(LL_C2_APB3_GRP1_PERIPH_BLE)
#define __HAL_RCC_C2802_CLK_SLEEP_DISABLE()         LL_C2_APB3_GRP1_DisableClockSleep(LL_C2_APB3_GRP1_PERIPH_802)
/**
  * @}
  */

/** @defgroup RCC_C2APB3_Clock_Sleep_Enable_Disable_Status APB3 Peripheral Clock Sleep Enabled or Disabled Status
  * @brief  Check whether the APB3 peripheral clock during Low Power (Sleep) mode is enabled or not.
  * @note   Peripheral clock gating in SLEEP mode can be used to further reduce
  *         power consumption.
  * @note   After wakeup from SLEEP mode, the peripheral clock is enabled again.
  * @note   By default, all peripheral clocks are enabled during SLEEP mode.
  * @{
  */
#define __HAL_RCC_C2BLE_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB3SMENR, RCC_C2APB3SMENR_BLESMEN) != RESET)
#define __HAL_RCC_C2802_IS_CLK_SLEEP_ENABLED()           (READ_BIT(RCC->C2APB3SMENR, RCC_C2APB3SMENR_802SMEN) != RESET)

#define __HAL_RCC_C2BLE_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB3SMENR, RCC_C2APB3SMENR_BLESMEN) == RESET)
#define __HAL_RCC_C2802_IS_CLK_SLEEP_DISABLED()           (READ_BIT(RCC->C2APB3SMENR, RCC_C2APB3SMENR_802SMEN) == RESET)
/**
  * @}
  */

/** @defgroup RCC_Backup_Domain_Reset RCC Backup Domain Reset
  * @{
  */

/** @brief  Macros to force or release the Backup domain reset.
  * @note   This function resets the RTC peripheral (including the backup registers)
  *         and the RTC clock source selection in RCC_CSR register.
  * @note   The BKPSRAM is not affected by this reset.
  * @retval None
  */
#define __HAL_RCC_BACKUPRESET_FORCE()   LL_RCC_ForceBackupDomainReset()
#define __HAL_RCC_BACKUPRESET_RELEASE() LL_RCC_ReleaseBackupDomainReset()

/**
  * @}
  */

/** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration
  * @{
  */

/** @brief  Macros to enable or disable the RTC clock.
  * @note   As the RTC is in the Backup domain and write access is denied to
  *         this domain after reset, you have to enable write access using
  *         HAL_PWR_EnableBkUpAccess() function before to configure the RTC
  *         (to be done once after reset).
  * @note   These macros must be used after the RTC clock source was selected.
  * @retval None
  */
#define __HAL_RCC_RTC_ENABLE()         LL_RCC_EnableRTC()
#define __HAL_RCC_RTC_DISABLE()        LL_RCC_DisableRTC()

/**
  * @}
  */

/** @brief  Macros to enable the Internal High Speed oscillator (HSI).
  * @note   The HSI is stopped by hardware when entering STOP, STANDBY or SHUTDOWN modes.
  *         It is enabled by hardware to force the HSI oscillator ON when STOPWUCK=1
  *         or HSIASFS = 1 when leaving Stop modes, or in case of failure of the HSE
  *         crystal oscillator and Security System CSS is enabled.
  * @note   After enabling the HSI, the application software should wait on HSIRDY
  *         flag to be set indicating that HSI clock is stable and can be used as
  *         system clock source.
  * @retval None
  */
#define __HAL_RCC_HSI_ENABLE()  LL_RCC_HSI_Enable()

/** @brief  Macro to disable the Internal High Speed oscillator (HSI).
  * @note   HSI can not be stopped if it is used as system clock source. In this case,
  *         you have to select another source of the system clock then stop the HSI.
  * @note   When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator
  *         clock cycles.
  * @retval None
  */
#define __HAL_RCC_HSI_DISABLE() LL_RCC_HSI_Disable()

/** @brief  Macro to adjust the Internal High Speed oscillator (HSI) calibration value.
  * @note   The calibration is used to compensate for the variations in voltage
  *         and temperature that influence the frequency of the internal HSI RC.
  * @param  __HSICALIBRATIONVALUE__ specifies the calibration trimming value
  *         (default is RCC_HSICALIBRATION_DEFAULT).
  *         This parameter must be a number between Min_data=0 and Max_Data=127.
  * @retval None
  */
#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(__HSICALIBRATIONVALUE__)  LL_RCC_HSI_SetCalibTrimming(__HSICALIBRATIONVALUE__)

/**
  * @brief    Macros to enable or disable the wakeup the Internal High Speed oscillator (HSI)
  *           in parallel to the Internal Multi Speed oscillator (MSI) used at system wakeup.
  * @note     The enable of this function has not effect on the HSION bit.
  *           This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
#define __HAL_RCC_HSIAUTOMATIC_START_ENABLE()   LL_RCC_HSI_EnableAutoFromStop()
#define __HAL_RCC_HSIAUTOMATIC_START_DISABLE()  LL_RCC_HSI_DisableAutoFromStop()

/**
  * @brief    Macros to enable or disable the force of the Internal High Speed oscillator (HSI)
  *           in STOP mode to be quickly available as kernel clock for USARTs and I2Cs.
  * @note     Keeping the HSI ON in STOP mode allows to avoid slowing down the communication
  *           speed because of the HSI startup time.
  * @note     The enable of this function has not effect on the HSION bit.
  * @retval None
  */
#define __HAL_RCC_HSISTOP_ENABLE()     LL_RCC_HSI_EnableInStopMode()
#define __HAL_RCC_HSISTOP_DISABLE()    LL_RCC_HSI_DisableInStopMode()

/**
  * @brief  Macros to enable or disable the Internal Multi Speed oscillator (MSI).
  * @note   The MSI is stopped by hardware when entering STOP and STANDBY modes.
  *         It is used (enabled by hardware) as system clock source after
  *         startup from Reset, wakeup from STOP and STANDBY mode, or in case
  *         of failure of the HSE used directly or indirectly as system clock
  *         (if the Clock Security System CSS is enabled).
  * @note   MSI can not be stopped if it is used as system clock source.
  *         In this case, you have to select another source of the system
  *         clock then stop the MSI.
  * @note   After enabling the MSI, the application software should wait on
  *         MSIRDY flag to be set indicating that MSI clock is stable and can
  *         be used as system clock source.
  * @note   When the MSI is stopped, MSIRDY flag goes low after 6 MSI oscillator
  *         clock cycles.
  * @retval None
  */
#define __HAL_RCC_MSI_ENABLE()  LL_RCC_MSI_Enable()
#define __HAL_RCC_MSI_DISABLE() LL_RCC_MSI_Disable()

/** @brief  Macro to adjust the Internal Multi Speed oscillator (MSI) calibration value.
  * @note   The calibration is used to compensate for the variations in voltage
  *         and temperature that influence the frequency of the internal MSI RC.
  *         Refer to the Application Note AN3300 for more details on how to
  *         calibrate the MSI.
  * @param  __MSICALIBRATIONVALUE__  specifies the calibration trimming value
  *         (default is @ref RCC_MSICALIBRATION_DEFAULT).
  *         This parameter must be a number between 0 and 255.
  * @retval None
  */
#define __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(__MSICALIBRATIONVALUE__)  LL_RCC_MSI_SetCalibTrimming(__MSICALIBRATIONVALUE__)

/**
  * @brief  Macro configures the Internal Multi Speed oscillator (MSI) clock range in run mode
  * @note     After restart from Reset , the MSI clock is around 4 MHz.
  *           After stop the startup clock can be MSI (at any of its possible
  *           frequencies, the one that was used before entering stop mode) or HSI.
  *          After Standby its frequency can be selected between 4 possible values
  *          (1, 2, 4 or 8 MHz).
  * @note     MSIRANGE can be modified when MSI is OFF (MSION=0) or when MSI is ready
  *          (MSIRDY=1).
  * @note    The MSI clock range after reset can be modified on the fly.
  * @param  __MSIRANGEVALUE__  specifies the MSI clock range.
  *         This parameter must be one of the following values:
  *            @arg @ref RCC_MSIRANGE_0  MSI clock is around 100 KHz
  *            @arg @ref RCC_MSIRANGE_1  MSI clock is around 200 KHz
  *            @arg @ref RCC_MSIRANGE_2  MSI clock is around 400 KHz
  *            @arg @ref RCC_MSIRANGE_3  MSI clock is around 800 KHz
  *            @arg @ref RCC_MSIRANGE_4  MSI clock is around 1 MHz
  *            @arg @ref RCC_MSIRANGE_5  MSI clock is around 2MHz
  *            @arg @ref RCC_MSIRANGE_6  MSI clock is around 4MHz (default after Reset)
  *            @arg @ref RCC_MSIRANGE_7  MSI clock is around 8  MHz
  *            @arg @ref RCC_MSIRANGE_8  MSI clock is around 16 MHz
  *            @arg @ref RCC_MSIRANGE_9  MSI clock is around 24 MHz
  *            @arg @ref RCC_MSIRANGE_10 MSI clock is around 32 MHz
  *            @arg @ref RCC_MSIRANGE_11 MSI clock is around 48 MHz
  * @retval None
  */
#define __HAL_RCC_MSI_RANGE_CONFIG(__MSIRANGEVALUE__)  LL_RCC_MSI_SetRange(__MSIRANGEVALUE__)


/** @brief  Macro to get the Internal Multi Speed oscillator (MSI) clock range in run mode
  * @retval MSI clock range.
  *         This parameter must be one of the following values:
  *            @arg @ref RCC_MSIRANGE_0   MSI clock is around 100 KHz
  *            @arg @ref RCC_MSIRANGE_1   MSI clock is around 200 KHz
  *            @arg @ref RCC_MSIRANGE_2   MSI clock is around 400 KHz
  *            @arg @ref RCC_MSIRANGE_3   MSI clock is around 800 KHz
  *            @arg @ref RCC_MSIRANGE_4   MSI clock is around 1 MHz
  *            @arg @ref RCC_MSIRANGE_5   MSI clock is around 2 MHz
  *            @arg @ref RCC_MSIRANGE_6   MSI clock is around 4 MHz   (default after Reset)
  *            @arg @ref RCC_MSIRANGE_7   MSI clock is around 8 MHz
  *            @arg @ref RCC_MSIRANGE_8   MSI clock is around 16 MHz
  *            @arg @ref RCC_MSIRANGE_9   MSI clock is around 24 MHz
  *            @arg @ref RCC_MSIRANGE_10  MSI clock is around 32 MHz
  *            @arg @ref RCC_MSIRANGE_11  MSI clock is around 48 MHz
  */
#define __HAL_RCC_GET_MSI_RANGE()    LL_RCC_MSI_GetRange()


/** @brief  Macros to enable or disable the Internal Low Speed oscillator (LSI1).
  * @note   After enabling the LSI1, the application software should wait on
  *         LSI1RDY flag to be set indicating that LSI1 clock is stable and can
  *         be used to clock the IWDG and/or the RTC.
  * @retval None
  */
#define __HAL_RCC_LSI1_ENABLE()         LL_RCC_LSI1_Enable()
#define __HAL_RCC_LSI1_DISABLE()        LL_RCC_LSI1_Disable()

/** @brief  Macros to enable or disable the Internal Low Speed oscillator (LSI2).
  * @note   After enabling the LSI2, the application software should wait on
  *         LSI2RDY flag to be set indicating that LSI2 clock is stable and can
  *         be used to clock the IWDG and/or the RTC.
  * @retval None
  */
#define __HAL_RCC_LSI2_ENABLE()         LL_RCC_LSI2_Enable()
#define __HAL_RCC_LSI2_DISABLE()        LL_RCC_LSI2_Disable()

/** @brief  Macro to adjust the Internal Low Speed oscillator (LSI2) calibration value.
  * @note   The calibration is used to compensate for the variations in voltage
  *         and temperature that influence the frequency of the internal HSI RC.
  * @param  __LSI2TRIMMINGVALUE__ specifies the calibration trimming value
  *         This parameter must be a number between Min_data=0 and Max_Data=15.
  * @retval None
  */
#define __HAL_RCC_LSI2_CALIBRATIONVALUE_ADJUST(__LSI2TRIMMINGVALUE__)  LL_RCC_LSI2_SetTrimming(__LSI2TRIMMINGVALUE__)

/**
  * @brief  Macro to configure the External High Speed oscillator (HSE).
  * @note   Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not
  *         supported by this macro. User should request a transition to HSE Off
  *         first and then HSE On or HSE Bypass.
  * @note   After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application
  *         software should wait on HSERDY flag to be set indicating that HSE clock
  *         is stable and can be used to clock the PLL and/or system clock.
  * @note   HSE state can not be changed if it is used directly or through the
  *         PLL as system clock. In this case, you have to select another source
  *         of the system clock then change the HSE state (ex. disable it).
  * @note   The HSE is stopped by hardware when entering STOP and STANDBY modes.
  * @note   This function reset the CSSON bit, so if the clock security system(CSS)
  *         was previously enabled you have to enable it again after calling this
  *         function.
  * @param  __STATE__  specifies the new state of the HSE.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_HSE_OFF  Turn OFF the HSE oscillator, HSERDY flag goes low after
  *                              6 HSE oscillator clock cycles.
  *            @arg @ref RCC_HSE_ON  Turn ON the HSE oscillator.
  *            @arg @ref RCC_HSE_BYPASS  HSE oscillator bypassed with external clock.
  * @retval None
  */
#define __HAL_RCC_HSE_CONFIG(__STATE__)                      \
                    do {                                     \
                      if((__STATE__) == RCC_HSE_ON)          \
                      {                                      \
                       LL_RCC_HSE_Enable();                  \
                      }                                      \
                      else if((__STATE__) == RCC_HSE_BYPASS) \
                      {                                      \
                        LL_RCC_HSE_EnableBypass();           \
                        LL_RCC_HSE_Enable();                 \
                      }                                      \
                      else                                   \
                      {                                      \
                        LL_RCC_HSE_Disable();                \
                        LL_RCC_HSE_DisableBypass();          \
                      }                                      \
                    } while(0U)

/** @brief  Macros to enable or disable the HSE Prescaler
  * @note   HSE div2 could be used as Sysclk or PLL entry in Range2
  * @retval None
  */
#define __HAL_RCC_HSE_DIV2_ENABLE()         LL_RCC_HSE_EnableDiv2()
#define __HAL_RCC_HSE_DIV2_DISABLE()        LL_RCC_HSE_DisableDiv2()

/**
  * @brief  Macro to configure the External Low Speed oscillator (LSE).
  * @note   Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not
  *         supported by this macro. User should request a transition to LSE Off
  *         first and then LSE On or LSE Bypass.
  * @note   As the LSE is in the Backup domain and write access is denied to
  *         this domain after reset, you have to enable write access using
  *         HAL_PWR_EnableBkUpAccess() function before to configure the LSE
  *         (to be done once after reset).
  * @note   After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application
  *         software should wait on LSERDY flag to be set indicating that LSE clock
  *         is stable and can be used to clock the RTC.
  * @param  __STATE__  specifies the new state of the LSE.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_LSE_OFF  Turn OFF the LSE oscillator, LSERDY flag goes low after
  *                              6 LSE oscillator clock cycles.
  *            @arg @ref RCC_LSE_ON  Turn ON the LSE oscillator.
  *            @arg @ref RCC_LSE_BYPASS  LSE oscillator bypassed with external clock.
  * @retval None
  */
#define __HAL_RCC_LSE_CONFIG(__STATE__)                        \
                    do {                                       \
                      if((__STATE__) == RCC_LSE_ON)            \
                      {                                        \
                        LL_RCC_LSE_Enable();                   \
                      }                                        \
                      else if((__STATE__) == RCC_LSE_BYPASS)   \
                      {                                        \
                        LL_RCC_LSE_EnableBypass();             \
                        LL_RCC_LSE_Enable();                   \
                      }                                        \
                      else                                     \
                      {                                        \
                        LL_RCC_LSE_Disable();                  \
                        LL_RCC_LSE_DisableBypass();            \
                      }                                        \
                    } while(0U)


/** @brief  Macros to enable or disable the Internal High Speed 48MHz oscillator (HSI48).
  * @note   The HSI48 is stopped by hardware when entering STOP and STANDBY modes.
  * @note   After enabling the HSI48, the application software should wait on HSI48RDY
  *         flag to be set indicating that HSI48 clock is stable.
  *         This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
#define __HAL_RCC_HSI48_ENABLE()  LL_RCC_HSI48_Enable()
#define __HAL_RCC_HSI48_DISABLE() LL_RCC_HSI48_Disable()

/** @brief  Macros to configure HSE sense amplifier threshold.
  * @note   to configure HSE sense amplifier, first disable HSE
  *         using @ref __HAL_RCC_HSE_CONFIG(RCC_HSE_OFF) macro.
  *
  * @param  __HSE_AMPTHRES__  specifies the HSE sense amplifier threshold.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_HSEAMPTHRESHOLD_1_2  HSE bias current factor 1/2.
  *            @arg @ref RCC_HSEAMPTHRESHOLD_3_4  HSE bias current factor 3/4.
  * @retval None
  */
#define __HAL_RCC_HSE_AMPCONFIG(__HSE_AMPTHRES__)  LL_RCC_HSE_SetSenseAmplifier(__HSE_AMPTHRES__)

/** @brief  Macros to configure HSE current control.
  * @note   to configure HSE current control, first disable HSE
  *         using @ref __HAL_RCC_HSE_CONFIG(RCC_HSE_OFF) macro.
  *
  * @param  __HSE_CURRENTMAX__  specifies the HSE current max limit.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_HSE_CURRENTMAX_0  HSE current max limit 0.18 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_1  HSE current max limit 0.57 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_2  HSE current max limit 0.78 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_3  HSE current max limit 1.13 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_4  HSE current max limit 0.61 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_5  HSE current max limit 1.65 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_6  HSE current max limit 2.12 mA/V.
  *            @arg @ref RCC_HSE_CURRENTMAX_7  HSE current max limit 2.84 mA/V.
  * @retval None
  */
#define __HAL_RCC_HSE_CURRENTCONFIG(__HSE_CURRENTMAX__)  LL_RCC_HSE_SetCurrentControl(__HSE_CURRENTMAX__)

/** @brief  Macros to configure HSE capacitor tuning.
  * @note   to configure HSE current control, first disable HSE
  *         using __HAL_RCC_HSE_CONFIG(RCC_HSE_OFF) macro.
  *
  * @param  __HSE_LOAD_CAPACITANCE__  specifies the HSE capacitor value.
  *         This Value Between Min_Data = 0 and Max_Data = 63
  * @retval None
  */
#define __HAL_RCC_HSE_CAPACITORTUNING(__HSE_LOAD_CAPACITANCE__)  LL_RCC_HSE_SetCapacitorTuning(__HSE_LOAD_CAPACITANCE__)


/** @brief  Macros to configure the RTC clock (RTCCLK).
  * @note   As the RTC clock configuration bits are in the Backup domain and write
  *         access is denied to this domain after reset, you have to enable write
  *         access using the Power Backup Access macro before to configure
  *         the RTC clock source (to be done once after reset).
  * @note   Once the RTC clock is configured it cannot be changed unless the
  *         Backup domain is reset using @ref __HAL_RCC_BACKUPRESET_FORCE() macro, or by
  *         a Power On Reset (POR).
  *
  * @param  __RTC_CLKSOURCE__  specifies the RTC clock source.
  *         This parameter can be one of the following values:*
  *            @arg @ref RCC_RTCCLKSOURCE_NONE  none clock selected as RTC clock.
  *            @arg @ref RCC_RTCCLKSOURCE_LSE  LSE selected as RTC clock.
  *            @arg @ref RCC_RTCCLKSOURCE_LSI  LSI selected as RTC clock.
  *            @arg @ref RCC_RTCCLKSOURCE_HSE_DIV32  HSE clock divided by 32 selected
  *
  * @note   If the LSE or LSI is used as RTC clock source, the RTC continues to
  *         work in STOP and STANDBY modes, and can be used as wakeup source.
  *         However, when the HSE clock is used as RTC clock source, the RTC
  *         cannot be used in STOP and STANDBY modes.
  * @note   The maximum input clock frequency for RTC is 1MHz (when using HSE as
  *         RTC clock source).
  * @retval None
  */
#define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__)  LL_RCC_SetRTCClockSource(__RTC_CLKSOURCE__)


/** @brief  Macro to get the RTC clock source.
  * @retval The returned value can be one of the following:
  *            @arg @ref RCC_RTCCLKSOURCE_NONE  none clock selected as RTC clock.
  *            @arg @ref RCC_RTCCLKSOURCE_LSE  LSE selected as RTC clock.
  *            @arg @ref RCC_RTCCLKSOURCE_LSI  LSI selected as RTC clock.
  *            @arg @ref RCC_RTCCLKSOURCE_HSE_DIV32  HSE clock divided by 32 selected
  */
#define  __HAL_RCC_GET_RTC_SOURCE() LL_RCC_GetRTCClockSource()

/** @brief  Macros to enable or disable the main PLL.
  * @note   After enabling the main PLL, the application software should wait on
  *         PLLRDY flag to be set indicating that PLL clock is stable and can
  *         be used as system clock source.
  * @note   The main PLL can not be disabled if it is used as system clock source
  * @note   The main PLL is disabled by hardware when entering STOP and STANDBY modes.
  * @retval None
  */
#define __HAL_RCC_PLL_ENABLE()         LL_RCC_PLL_Enable()
#define __HAL_RCC_PLL_DISABLE()        LL_RCC_PLL_Disable()

/** @brief  Macro to configure the PLL clock source.
  * @note   This function must be used only when the main PLL is disabled.
  * @param  __PLLSOURCE__  specifies the PLL entry clock source.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_PLLSOURCE_NONE  No clock selected as PLL clock entry
  *            @arg @ref RCC_PLLSOURCE_MSI  MSI oscillator clock selected as PLL clock entry
  *            @arg @ref RCC_PLLSOURCE_HSI  HSI oscillator clock selected as PLL clock entry
  *            @arg @ref RCC_PLLSOURCE_HSE  HSE oscillator clock selected as PLL clock entry
  * @note   This clock source is common for the main PLL and audio PLL (PLL and PLLSAI1).
  * @retval None
  *
  */
#define __HAL_RCC_PLL_PLLSOURCE_CONFIG(__PLLSOURCE__) \
                  MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLSRC, (__PLLSOURCE__))

/** @brief  Macro to configure the PLL multiplication factor.
  * @note   This function must be used only when the main PLL is disabled.
  * @param  __PLLM__  specifies the division factor for PLL VCO input clock
  *         This parameter must be a value of @ref RCC_PLLM_Clock_Divider.
  * @note   You have to set the PLLM parameter correctly to ensure that the VCO input
  *         frequency ranges from 4 to 16 MHz. It is recommended to select a frequency
  *         of 16 MHz to limit PLL jitter.
  * @retval None
  *
  */
#define __HAL_RCC_PLL_PLLM_CONFIG(__PLLM__) \
                  MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLM, (__PLLM__))

/**
  * @brief  Macro to configure the main PLL clock source, multiplication and division factors.
  * @note   This function must be used only when the main PLL is disabled.
  *
  * @param  __PLLSOURCE__  specifies the PLL entry clock source.
  *          This parameter can be one of the following values:
  *            @arg @ref RCC_PLLSOURCE_NONE  No clock selected as PLL clock entry
  *            @arg @ref RCC_PLLSOURCE_MSI  MSI oscillator clock selected as PLL clock entry
  *            @arg @ref RCC_PLLSOURCE_HSI  HSI oscillator clock selected as PLL clock entry
  *            @arg @ref RCC_PLLSOURCE_HSE  HSE oscillator clock selected as PLL clock entry
  * @note   This clock source is common for the main PLL and audio PLL (PLL and PLLSAI1).
  *
  * @param  __PLLM__  specifies the division factor for PLL VCO input clock.
  *         This parameter must be a value of @ref RCC_PLLM_Clock_Divider.
  * @note   You have to set the PLLM parameter correctly to ensure that the VCO input
  *         frequency ranges from 2.66 to 16 MHz. It is recommended to select a frequency
  *         of 16 MHz to limit PLL jitter.
  *
  * @param  __PLLN__  specifies the multiplication factor for PLL VCO output clock.
  *         This parameter must be a number between 6 and 127.
  * @note   You have to set the PLLN parameter correctly to ensure that the VCO
  *         output frequency is between 96 and 344 MHz.
  *
  * @param  __PLLP__  specifies the division factor for ADC and SAI1 clock.
  *         This parameter must be a value of @ref RCC_PLLP_Clock_Divider.
  *
  * @param  __PLLQ__  specifies the division factor for USB and RNG clocks.
  *         This parameter must be a value of @ref RCC_PLLQ_Clock_Divider
  * @note   If the USB FS is used in your application, you have to set the
  *         PLLQ parameter correctly to have 48 MHz clock for the USB. However,
  *         the RNG need a frequency lower than or equal to 48 MHz to work
  *         correctly.
  *
  * @param  __PLLR__  specifies the division factor for the main system clock.
  *         This parameter must be a value of @ref RCC_PLLR_Clock_Divider
  * @note   You have to set the PLLR parameter correctly to not exceed 48 MHZ.
  * @retval None
  */
#define __HAL_RCC_PLL_CONFIG(__PLLSOURCE__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__ ) \
                  MODIFY_REG( RCC->PLLCFGR,                                                   \
                             (RCC_PLLCFGR_PLLSRC                              |               \
                              RCC_PLLCFGR_PLLM                                |               \
                              RCC_PLLCFGR_PLLN                                |               \
                              RCC_PLLCFGR_PLLP                                |               \
                              RCC_PLLCFGR_PLLQ                                |               \
                              RCC_PLLCFGR_PLLR),                                              \
                             ((uint32_t) (__PLLSOURCE__)                      |               \
                              (uint32_t) (__PLLM__)                           |               \
                              (uint32_t) ((__PLLN__) << RCC_PLLCFGR_PLLN_Pos) |               \
                              (uint32_t) (__PLLP__)                           |               \
                              (uint32_t) (__PLLQ__)                           |               \
                              (uint32_t) (__PLLR__)))

/** @brief  Macro to get the oscillator used as PLL clock source.
  * @retval The oscillator used as PLL clock source. The returned value can be one
  *         of the following:
  *              @arg @ref RCC_PLLSOURCE_NONE No oscillator is used as PLL clock source.
  *              @arg @ref RCC_PLLSOURCE_MSI MSI oscillator is used as PLL clock source.
  *              @arg @ref RCC_PLLSOURCE_HSI HSI oscillator is used as PLL clock source.
  *              @arg @ref RCC_PLLSOURCE_HSE HSE oscillator is used as PLL clock source.
  */
#define __HAL_RCC_GET_PLL_OSCSOURCE()  LL_RCC_PLL_GetMainSource()

/**
  * @brief  Enable or disable each clock output (RCC_PLL_SYSCLK, RCC_PLL_USBCLK, RCC_PLL_SAI1CLK)
  * @note   Enabling/disabling clock outputs RCC_PLL_SAI1CLK and RCC_PLL_USBCLK can be done at anytime
  *         without the need to stop the PLL in order to save power. But RCC_PLL_SYSCLK cannot
  *         be stopped if used as System Clock.
  * @param  __PLLCLOCKOUT__  specifies the PLL clock to be output.
  *          This parameter can be one or a combination of the following values:
  *            @arg @ref RCC_PLL_SAI1CLK  This clock is used to generate the clock for SAI
  *            @arg @ref RCC_PLL_ADCCLK  This clock is used to generate the clock for ADC
  *            @arg @ref RCC_PLL_USBCLK  This Clock is used to generate the clock for the USB FS (48 MHz)
  *            @arg @ref RCC_PLL_RNGCLK  This clock is used to generate the clock for RNG
  *            @arg @ref RCC_PLL_SYSCLK  This Clock is used to generate the high speed system clock (up to 64MHz)
  *            @arg @ref RCC_PLL_I2SCLK  This Clock is used to generate the clock for the I2S
  * @retval None
  */
#define __HAL_RCC_PLLCLKOUT_ENABLE(__PLLCLOCKOUT__)   SET_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__))

#define __HAL_RCC_PLLCLKOUT_DISABLE(__PLLCLOCKOUT__)  CLEAR_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__))

/**
  * @brief  Get clock output enable status (RCC_PLL_SYSCLK, RCC_PLL_USBCLK, RCC_PLL_SAI1CLK)
  * @param  __PLLCLOCKOUT__  specifies the output PLL clock to be checked.
  *          This parameter can be one of the following values:
  *            @arg @ref RCC_PLL_SAI1CLK  This clock is used to generate an accurate clock to achieve high-quality audio performance on SAI interface
  *            @arg @ref RCC_PLL_ADCCLK  same
  *            @arg @ref RCC_PLL_USBCLK  This Clock is used to generate the clock for the USB FS (48 MHz)
  *            @arg @ref RCC_PLL_RNGCLK  same
  *            @arg @ref RCC_PLL_SYSCLK  This Clock is used to generate the high speed system clock (up to 64MHz)
  * @retval SET / RESET
  */
#define __HAL_RCC_GET_PLLCLKOUT_CONFIG(__PLLCLOCKOUT__)  READ_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__))

/**
  * @brief  Macro to configure the system clock source.
  * @param  __SYSCLKSOURCE__  specifies the system clock source.
  *          This parameter can be one of the following values:
  *              @arg @ref RCC_SYSCLKSOURCE_MSI MSI oscillator is used as system clock source.
  *              @arg @ref RCC_SYSCLKSOURCE_HSI HSI oscillator is used as system clock source.
  *              @arg @ref RCC_SYSCLKSOURCE_HSE HSE oscillator is used as system clock source.
  *              @arg @ref RCC_SYSCLKSOURCE_PLLCLK PLL output is used as system clock source.
  * @retval None
  */
#define __HAL_RCC_SYSCLK_CONFIG(__SYSCLKSOURCE__)  LL_RCC_SetSysClkSource(__SYSCLKSOURCE__)

/** @brief  Macro to get the clock source used as system clock.
  * @retval The clock source used as system clock. The returned value can be one
  *         of the following:
  *              @arg @ref RCC_SYSCLKSOURCE_STATUS_MSI MSI used as system clock.
  *              @arg @ref RCC_SYSCLKSOURCE_STATUS_HSI HSI used as system clock.
  *              @arg @ref RCC_SYSCLKSOURCE_STATUS_HSE HSE used as system clock.
  *              @arg @ref RCC_SYSCLKSOURCE_STATUS_PLLCLK PLL used as system clock.
  */
#define __HAL_RCC_GET_SYSCLK_SOURCE()  LL_RCC_GetSysClkSource()

/**
  * @brief  Macro to configure the External Low Speed oscillator (LSE) drive capability.
  * @note   As the LSE is in the Backup domain and write access is denied to
  *         this domain after reset, you have to enable write access using
  *         HAL_PWR_EnableBkUpAccess() function before to configure the LSE
  *         (to be done once after reset).
  * @param  __LSEDRIVE__  specifies the new state of the LSE drive capability.
  *          This parameter can be one of the following values:
  *            @arg @ref RCC_LSEDRIVE_LOW  LSE oscillator low drive capability.
  *            @arg @ref RCC_LSEDRIVE_MEDIUMLOW  LSE oscillator medium low drive capability.
  *            @arg @ref RCC_LSEDRIVE_MEDIUMHIGH  LSE oscillator medium high drive capability.
  *            @arg @ref RCC_LSEDRIVE_HIGH  LSE oscillator high drive capability.
  * @retval None
  */
#define __HAL_RCC_LSEDRIVE_CONFIG(__LSEDRIVE__)  LL_RCC_LSE_SetDriveCapability(__LSEDRIVE__)

/**
  * @brief  Macro to configure the wake up from stop clock.
  * @param  __STOPWUCLK__  specifies the clock source used after wake up from stop.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_STOP_WAKEUPCLOCK_MSI  MSI selected as system clock source
  *            @arg @ref RCC_STOP_WAKEUPCLOCK_HSI  HSI selected as system clock source
  * @retval None
  */
#define __HAL_RCC_WAKEUPSTOP_CLK_CONFIG(__STOPWUCLK__)  LL_RCC_SetClkAfterWakeFromStop(__STOPWUCLK__)


/** @brief  Macro to configure the MCO clock.
  * @param  __MCOCLKSOURCE__ specifies the MCO clock source.
  *          This parameter can be one of the following values:
  *            @arg @ref RCC_MCO1SOURCE_NOCLOCK  MCO output disabled
  *            @arg @ref RCC_MCO1SOURCE_SYSCLK  System  clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_MSI     MSI clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_HSI     HSI clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_HSE     HSE clock selected as MCO sourcee
  *            @arg @ref RCC_MCO1SOURCE_PLLCLK  Main PLL clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_LSI1    LSI1 clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_LSI2    LSI2 clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_LSE     LSE clock selected as MCO source
  *            @arg @ref RCC_MCO1SOURCE_HSI48    HSI48 clock selected as MCO source

  * @param  __MCODIV__ specifies the MCO clock prescaler.
  *          This parameter can be one of the following values:
  *            @arg @ref RCC_MCODIV_1   MCO clock source is divided by 1
  *            @arg @ref RCC_MCODIV_2   MCO clock source is divided by 2
  *            @arg @ref RCC_MCODIV_4   MCO clock source is divided by 4
  *            @arg @ref RCC_MCODIV_8   MCO clock source is divided by 8
  *            @arg @ref RCC_MCODIV_16  MCO clock source is divided by 16
  */
#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__)  LL_RCC_ConfigMCO((__MCOCLKSOURCE__), (__MCODIV__))


/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management
  * @brief macros to manage the specified RCC Flags and interrupts.
  * @{
  */

/** @brief  Enable RCC interrupt.
  * @param  __INTERRUPT__  specifies the RCC interrupt sources to be enabled.
  *         This parameter can be any combination of the following values:
  *            @arg @ref RCC_IT_LSI1RDY     LSI1 ready interrupt enable
  *            @arg @ref RCC_IT_LSERDY      LSE ready interrupt enable
  *            @arg @ref RCC_IT_MSIRDY      HSI ready interrupt enable
  *            @arg @ref RCC_IT_HSIRDY      HSI ready interrupt enable
  *            @arg @ref RCC_IT_HSERDY      HSE ready interrupt enable
  *            @arg @ref RCC_IT_PLLRDY      Main PLL ready interrupt enable
  *            @arg @ref RCC_IT_PLLSAI1RDY  PLLSAI1 ready interrupt enable
  *            @arg @ref RCC_IT_LSECSS      LSE Clock security system interrupt enable
  *            @arg @ref RCC_IT_HSI48RDY PLLHSI48 ready interrupt enable
  *            @arg @ref RCC_IT_LSI2RDY     LSI2 ready interrupt enable
  * @retval None
  */
#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) SET_BIT(RCC->CIER, (__INTERRUPT__))

/** @brief Disable RCC interrupt.
  * @param  __INTERRUPT__  specifies the RCC interrupt sources to be disabled.
    *         This parameter can be any combination of the following values:
  *            @arg @ref RCC_IT_LSI1RDY     LSI1 ready interrupt enable
  *            @arg @ref RCC_IT_LSERDY      LSE ready interrupt enable
  *            @arg @ref RCC_IT_MSIRDY      HSI ready interrupt enable
  *            @arg @ref RCC_IT_HSIRDY      HSI ready interrupt enable
  *            @arg @ref RCC_IT_HSERDY      HSE ready interrupt enable
  *            @arg @ref RCC_IT_PLLRDY      Main PLL ready interrupt enable
  *            @arg @ref RCC_IT_PLLSAI1RDY  PLLSAI1 ready interrupt enable
  *            @arg @ref RCC_IT_LSECSS      LSE Clock security system interrupt enable
  *            @arg @ref RCC_IT_HSI48RDY    PLLHSI48 ready interrupt enable
  *            @arg @ref RCC_IT_LSI2RDY     LSI2 ready interrupt enable
  * @retval None
  */
#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) CLEAR_BIT(RCC->CIER, (__INTERRUPT__))

/** @brief  Clear RCC interrupt pending bits (Perform Byte access to RCC_CICR[17:0]
  *         bits to clear the selected interrupt pending bits.
  * @param  __INTERRUPT__  specifies the interrupt pending bit to clear.
  *         This parameter can be any combination of the following values:
  *            @arg @ref RCC_IT_LSI1RDY  LSI1 ready interrupt clear
  *            @arg @ref RCC_IT_LSERDY   LSE ready interrupt clear
  *            @arg @ref RCC_IT_MSIRDY   HSI ready interrupt clear
  *            @arg @ref RCC_IT_HSIRDY   HSI ready interrupt clear
  *            @arg @ref RCC_IT_HSERDY   HSE ready interrupt clear
  *            @arg @ref RCC_IT_PLLRDY   Main PLL ready interrupt clear
  *            @arg @ref RCC_IT_PLLRDY   PLLSAI1 ready interrupt clear
  *            @arg @ref RCC_IT_HSECSS   HSE Clock security system interrupt clear
  *            @arg @ref RCC_IT_LSECSS   LSE Clock security system interrupt clear
  *            @arg @ref RCC_IT_HSI48RDY PLLHSI48 ready interrupt clear
  *            @arg @ref RCC_IT_LSI2RDY  LSI2 ready interrupt clear
  */
#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (RCC->CICR = (__INTERRUPT__))

/** @brief  Check whether the RCC interrupt has occurred or not.
  * @param  __INTERRUPT__  specifies the RCC interrupt source to check.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_IT_LSI1RDY  LSI1 ready interrupt flag
  *            @arg @ref RCC_IT_LSERDY   LSE ready interrupt flag
  *            @arg @ref RCC_IT_MSIRDY   HSI ready interrupt flag
  *            @arg @ref RCC_IT_HSIRDY   HSI ready interrupt flag
  *            @arg @ref RCC_IT_HSERDY   HSE ready interrupt flag
  *            @arg @ref RCC_IT_PLLRDY   Main PLL ready interrupt flag
  *            @arg @ref RCC_IT_PLLRDY   PLLSAI1 ready interrupt flag
  *            @arg @ref RCC_IT_HSECSS   HSE Clock security system interrupt flag
  *            @arg @ref RCC_IT_LSECSS   LSE Clock security system interrupt flag
  *            @arg @ref RCC_IT_HSI48RDY PLLHSI48 ready interrupt flag
  *            @arg @ref RCC_IT_LSI2RDY  LSI2 ready interrupt flag
  * @retval The new state of __INTERRUPT__ (TRUE or FALSE).
  */
#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIFR & (__INTERRUPT__)) == (__INTERRUPT__))

/** @brief Set RMVF bit to clear the reset flags.
  *        The reset flags are: RCC_FLAG_OBLRST, RCC_FLAG_PINRST, RCC_FLAG_BORRST,
  *        RCC_FLAG_SFTRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST and RCC_FLAG_LPWRRST.
  * @retval None
 */
#define __HAL_RCC_CLEAR_RESET_FLAGS() LL_RCC_ClearResetFlags()

/** @brief  Check whether the selected RCC flag is set or not.
  * @param  __FLAG__  specifies the flag to check.
  *         This parameter can be one of the following values:
  *            @arg @ref RCC_FLAG_MSIRDY  MSI oscillator clock ready
  *            @arg @ref RCC_FLAG_HSIRDY  HSI oscillator clock ready
  *            @arg @ref RCC_FLAG_HSERDY  HSE oscillator clock ready
  *            @arg @ref RCC_FLAG_PLLRDY  Main PLL clock ready
  *            @arg @ref RCC_FLAG_PLLRDY  PLLSAI1 clock ready
  *            @arg @ref RCC_FLAG_HSI48RDY  HSI48 clock ready for devices with HSI48
  *            @arg @ref RCC_FLAG_LSERDY  LSE oscillator clock ready
  *            @arg @ref RCC_FLAG_LSECSSD  Clock security system failure on LSE oscillator detection
  *            @arg @ref RCC_FLAG_LSI1RDY  LSI1 oscillator clock ready
  *            @arg @ref RCC_FLAG_LSI2RDY  LSI2 oscillator clock ready
  *            @arg @ref RCC_FLAG_BORRST  BOR reset
  *            @arg @ref RCC_FLAG_OBLRST  OBLRST reset
  *            @arg @ref RCC_FLAG_PINRST  Pin reset
  *            @arg @ref RCC_FLAG_SFTRST  Software reset
  *            @arg @ref RCC_FLAG_IWDGRST  Independent Watchdog reset
  *            @arg @ref RCC_FLAG_WWDGRST  Window Watchdog reset
  *            @arg @ref RCC_FLAG_LPWRRST  Low Power reset
  * @retval The new state of __FLAG__ (TRUE or FALSE).
  */
#define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == CR_REG_INDEX) ? RCC->CR :                     \
                                        ((((__FLAG__) >> 5U) == CRRCR_REG_INDEX) ? RCC->CRRCR :                  \
                                        ((((__FLAG__) >> 5U) == BDCR_REG_INDEX) ? RCC->BDCR :                   \
                                        ((((__FLAG__) >> 5U) == CSR_REG_INDEX) ? RCC->CSR : RCC->CIFR)))) &    \
                                        (1U << ((__FLAG__) & RCC_FLAG_MASK))) != RESET) \
                                         ? 1U : 0U)

/**
  * @}
  */

/**
  * @}
  */

/* Include RCC HAL Extended module */
#include "stm32wbxx_hal_rcc_ex.h"

/* Exported functions --------------------------------------------------------*/
/** @addtogroup RCC_Exported_Functions
  * @{
  */


/** @addtogroup RCC_Exported_Functions_Group1
  * @{
  */

/* Initialization and de-initialization functions  ******************************/
HAL_StatusTypeDef HAL_RCC_DeInit(void);
HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency);

/**
  * @}
  */

/** @addtogroup RCC_Exported_Functions_Group2
  * @{
  */

/* Peripheral Control functions  ************************************************/
void              HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv);
void              HAL_RCC_EnableCSS(void);
uint32_t          HAL_RCC_GetSysClockFreq(void);

uint32_t          HAL_RCC_GetHCLKFreq(void);
uint32_t          HAL_RCC_GetHCLK2Freq(void);
uint32_t          HAL_RCC_GetHCLK4Freq(void);

uint32_t          HAL_RCC_GetPCLK1Freq(void);
uint32_t          HAL_RCC_GetPCLK2Freq(void);

void              HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
void              HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency);
/* LSE & HSE CSS NMI IRQ handler */
void              HAL_RCC_NMI_IRQHandler(void);
/* User Callbacks in non blocking mode (IT mode) */
void              HAL_RCC_CSSCallback(void);

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

#ifdef __cplusplus
}
#endif

#endif /* STM32WBxx_HAL_RCC_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/