An .emb
file contains four sections: a documentation block, imports, an attribute block, containing attributes which apply to the whole module, followed by a list of type definitions:
# Documentation block (optional) -- This is an example of an .emb file, with every section. # Imports (optional) import "other.emb" as other import "project/more.emb" as project_more # Attribute block (optional) [$default byte_order: "LittleEndian"] [(cpp) namespace: "foo::bar::baz"] [(java) namespace: "com.example.foo.bar.baz"] # Type definitions enum Foo: ONE = 1 TEN = 10 PURPLE = 12 struct Bar: 0 [+4] Foo purple 4 [+4] UInt payload_size (s) 8 [+s] UInt:8[] payload
The documentation and/or attribute blocks may be omitted if they are not necessary.
Comments start with #
and extend to the end of the line:
struct Foo: # This is a comment # This is a comment 0 [+1] UInt field # This is a comment
Comments are ignored. They should not be confused with documentation, which is intended to be used by some back ends.
Documentation blocks may be attached to modules, types, fields, or enum values. They are different from comments in that they will be used by the (not-yet-ready) documentation generator back-end.
Documentation blocks take the form of any number of lines starting with --
:
-- This is a module documentation block. Text in this block will be attached to -- the module as documentation. -- -- This is a new paragraph in the same module documentation block. -- -- Module-level documentation should describe the purpose of the module, and may -- point out the most salient features of the module. struct Message: -- This is a documentation block attached to the Message structure. It should -- describe the purpose of Message, and how it should be used. 0 [+4] UInt header_length -- This is documentation for the header_length field. Again, it should -- describe this specific field. 4 [+4] MessageType message_type -- Short docs can go on the same line.
Documentation should be written in CommonMark format, ignoring the leading --
.
An import
line tells Emboss to read another .emb
file and make its types available to the current file under the given name. For example, given the import line:
import "other.emb" as helper
then the type Type
from other.emb
may be referenced as helper.Type
.
The --import-dir
command-line flag tells Emboss which directories to search for imported files; it may be specified multiple times. If no --import-dir
is specified, Emboss will search the current working directory.
Attributes are an extensible way of adding arbitrary information to a module, type, field, or enum value. Currently, only whitelisted attributes are allowed by the Emboss compiler, but this may change in the future.
Attributes take a form like:
[name: value] # name has value for the current entity. [$default name: value] # Default name to value for all sub-entities. [(backend) name: value] # Attribute for a specific back end.
byte_order
The byte_order
attribute is used to specify the byte order of bits
fields and of field with an atomic type, such as UInt
.
byte_order
takes a string value, which must be either "BigEndian"
, "LittleEndian"
, or "Null"
:
[$default byte_order: "LittleEndian"] struct Foo: [$default byte_order: "Null"] 0 [+4] UInt bar [byte_order: "BigEndian"] 4 [+4] bits: [byte_order: "LittleEndian"] 0 [+23] UInt baz 23 [+9] UInt qux 8 [+1] UInt froble
A $default
byte order may be set on a module or structure.
The "BigEndian"
and "LittleEndian"
byte orders set the byte order to big or little endian, respectively. That is, for little endian:
byte 0 byte 1 byte 2 byte 3 +--------+--------+--------+--------+ |76543210|76543210|76543210|76543210| +--------+--------+--------+--------+ ^ ^ ^ ^ ^ ^ ^ ^ 07 00 15 08 23 16 31 24 ^^^^^^^^^^^^^^^ bit ^^^^^^^^^^^^^^^
And for big endian:
byte 0 byte 1 byte 2 byte 3 +--------+--------+--------+--------+ |76543210|76543210|76543210|76543210| +--------+--------+--------+--------+ ^ ^ ^ ^ ^ ^ ^ ^ 31 24 23 16 15 08 07 00 ^^^^^^^^^^^^^^^ bit ^^^^^^^^^^^^^^^
The "Null"
byte order is used if no byte_order
attribute is specified. "Null"
indicates that the byte order is unknown; it is an error if a byte-order-dependent field that is not exactly 8 bits has the "Null"
byte order.
requires
The requires
attribute may be placed on an atomic field (e.g., type UInt
, Int
, Flag
, etc.) to specify a predicate that values of that field must satisfy, or on a struct
or bits
to specify relationships between fields that must be satisfied.
struct Foo: [requires: bar < qux] 0 [+4] UInt bar [requires: this <= 999_999_999] 4 [+4] UInt qux [requires: 100 <= this <= 1_000_000_000] let bar_plus_qux = bar + qux [requires: this >= 199]
For [requires]
on a field, other fields may not be referenced, and the value of the current field must be referred to as this
.
For [requires]
on a struct
or bits
, any atomic field in the structure may be referenced.
(cpp) namespace
The namespace
attribute is used by the C++ back end to determine which namespace to place the generated code in:
[(cpp) namespace: "foo::bar::baz"]
A leading ::
is allowed, but not required; the previous example could also be written as:
[(cpp) namespace: "::foo::bar::baz"]
Internally, Emboss will translate either of these into a nested namespace foo { namespace bar { namespace baz { ... } } }
wrapping the generated C++ code for this module.
The namespace
attribute may only be used at the module level; all structures and enums within a module will be placed in the same namespace.
text_output
The text_output
attribute may be attached to a struct
or bits
field to control whether or not the field is included when emitting the text format version of the structure. For example:
struct SuppressedField: 0 [+1] UInt a 1 [+1] UInt b [text_output: "Skip"]
The text format output (as from emboss::WriteToString()
in C++) would be of the form:
{ a: 1 }
instead of the default:
{ a: 1, b: 2 }
For completeness, [text_output: "Emit"]
may be used to explicitly specify that a field should be included in text output.
external
specifier attributesThe addressable_unit_size
, type_requires
, fixed_size_in_bits
, and is_integer
attributes are used on external
types to tell the compiler what it needs to know about the external
types. They are currently unstable, and should only be used internally.
Emboss allows you to define structs, unions, bits, and enums, and uses externals to define “basic types.” Types may be defined in any order, and may freely reference other types in the same module or any imported modules (including the implicitly-imported prelude).
struct
A struct
defines a view of a sequence of bytes. Each field of a struct
is a view of some particular subsequence of the struct
‘s bytes, whose interpretation is determined by the field’s type.
For example:
struct FramedMessage: -- A FramedMessage wraps a Message with magic bytes, lengths, and CRC. [$default byte_order: "LittleEndian"] 0 [+4] UInt magic_value 4 [+4] UInt header_length (h) 8 [+4] UInt message_length (m) h [+m] Message message h+m [+4] UInt crc32 [byte_order: "BigEndian"]
The first line introduces the struct
and gives it a name. This name may be used in field definitions to specify that the field has a structured type, and is used in the generated code. For example, to read the message_length
from a sequence of bytes in C++, you would construct a FramedMessageView
over the bytes:
// vector<uint8_t> bytes; auto framed_message_view = FramedMessageView(&bytes[0], bytes.size()); uint32_t message_length = framed_message_view.message_length().Read();
(Note that the FramedMessageView
does not take ownership of the bytes: it only provides a view of them.)
Each field starts with a byte range (0 [+4]
) that indicates where the field sits in the struct. For example, the magic_value
field covers the first four bytes of the struct.
Field locations do not have to be constants. In the example above, the message
field starts at the end of the header (as determined by the header_length
field) and covers message_length
bytes.
After the field‘s location is the field’s type. The type determines how the field's bytes are interpreted: the header_length
field will be interpreted as an unsigned integer (UInt
), while the message
field is interpreted as a Message
-- another struct
type defined elsewhere.
After the type is the field‘s name: this is a name used in the generated code to access that field, as in framed_message_view.message_length()
. The name may be followed by an optional abbreviation, like the (h)
after header_length
. The abbreviation can be used elsewhere in the struct
, but is not available in the generated code: framed_message_view.h()
wouldn’t compile.
Finally, fields may have attributes and documentation, just like any other Emboss construct.
struct
s and bits
can take runtime parameters:
struct Foo(x: Int:8, y: Int:8): 0 [+x] UInt:8[] xs x [+y] UInt:8[] ys enum Version: VERSION_1 = 10 VERSION_2 = 20 struct Bar(version: Version): 0 [+1] UInt payload if payload == 1 && version == Version.VERSION_1: 1 [+10] OldPayload1 old_payload_1 if payload == 1 && version == Version.VERSION_2: 1 [+12] NewPayload1 new_payload_1
Each parameter must have the form name:
type. Currently, the type can be:
UInt:
n
, where n
is a number from 1 to 64, inclusive.Int:
n
, where n
is a number from 1 to 64, inclusive.enum
type.UInt
- and Int
-typed parameters are integers with the corresponding range: for example, an Int:4
parameter can have any integer value from -8 to +7.
enum
-typed parameters can take any value in the enum
's native range. Note that Emboss enum
s are open, so unnamed values are allowed.
Parameterized structures can be included in other structures by passing their parameters:
struct Baz: 0 [+1] Version version 1 [+1] UInt:8 size 2 [+size] Bar(version) bar
It is possible to define a non-physical “field” whose value is an expression:
struct Foo: 0 [+4] UInt bar let two_bar = 2 * bar
These virtual “fields” may be used like any other field in most circumstances:
struct Bar: 0 [+4] Foo foo if foo.two_bar < 100: foo.two_bar [+4] UInt uint_at_offset_two_bar
Virtual fields may be integers, booleans, or an enum:
enum Size: SMALL = 1 LARGE = 2 struct Qux: 0 [+4] UInt x let x_is_big = x > 100 let x_size = x_is_big ? Size.LARGE : Size.SMALL
When a virtual field has a constant value, you may refer to it using its type:
struct Foo: let foo_offset = 0x120 0 [+4] UInt foo struct Bar: Foo.foo_offset [+4] Foo foo
This does not work for non-constant virtual fields:
struct Foo: 0 [+4] UInt foo let foo_offset = foo + 10 struct Bar: Foo.foo_offset [+4] Foo foo # Won't compile.
Note that, in some cases, you must use Type.field, and not field.field:
struct Foo: 0 [+4] UInt foo let foo_offset = 10 struct Bar: # Won't compile: foo.foo_offset depends on foo, which depends on # foo.foo_offset. foo.foo_offset [+4] Foo foo # Will compile: Foo.foo_offset is a static constant. Foo.foo_offset [+4] Foo foo
This limitation may be lifted in the future, but it has no practical effect.
Virtual fields of the form let x = y
or let x = y.z.q
are allowed even when y
or q
are composite fields. Virtuals of this form are considered to be aliases of the referred field; in generated code, they may be written as well as read, and writing through them is equivalent to writing to the aliased field.
Virtual fields of the forms let x1 = y + 1
, let x2 = 2 + y
, let x3 = y - 3
, and let x4 = 4 - y
, where y
is a writeable field, will be writeable in the generated code. When writing through these fields, the transformed field will be set to an appropriate value. For example, writing 5
to x1
will actually write 4
to y
, and writing 6
to x4
will write -2
to y
. This can be used to model fields whose raw values should be adjusted by some constant value, e.g.:
struct PosixDate: 0 [+1] Int raw_year -- Number of years since 1900. let year = raw_year + 1900 -- Gregorian year number. 1 [+1] Int zero_based_month -- Month number, from 0-11. Good for looking up a month name in a table. let month = zero_based_month + 1 -- Month number, from 1-12. Good for printing directly. 2 [+1] Int day -- Day number, one-based.
A struct
definition may contain other type definitions:
struct Foo: struct Bar: 0 [+2] UInt baz 2 [+2] UInt qux 0 [+4] Bar bar 4 [+4] Bar bar2
A struct
field may have fields which are only present under some circumstances. For example:
struct FramedMessage: 0 [+4] enum message_id: TYPE1 = 1 TYPE2 = 2 if message_id == MessageId.TYPE1: 4 [+16] Type1Message type_1_message if message_id == MessageId.TYPE2: 4 [+8] Type2Message type_2_message
The type_1_message
field will only be available if message_id
is TYPE1
, and similarly the type_2_message
field will only be available if message_id
is TYPE2
. If message_id
is some other value, then neither field will be available.
struct
It is possible to define a struct
inline in a struct
field. For example:
struct Message: [$default byte_order: "BigEndian"] 0 [+4] UInt message_length 4 [+4] struct payload: 0 [+1] UInt incoming 2 [+2] UInt scale_factor
This is equivalent to:
struct Message: [$default byte_order: "BigEndian"] struct Payload: 0 [+1] UInt incoming 2 [+2] UInt scale_factor 0 [+4] UInt message_length 4 [+4] Payload payload
This can be useful as a way to group related fields together.
A struct
will have $size_in_bytes
, $max_size_in_bytes
, and $min_size_in_bytes
virtual field automatically generated. These virtual field can be referenced inside the Emboss language just like any other virtual field:
struct Inner: 0 [+4] UInt field_a 4 [+4] UInt field_b struct Outer: 0 [+1] UInt message_type if message_type == 4: 4 [+Inner.$size_in_bytes] Inner payload
$size_in_bytes
An Emboss struct
has an intrinsic size, which is the size required to hold every field in the struct
, regardless of how many bytes are in the buffer that backs the struct
. For example:
struct FixedSize: 0 [+4] UInt long_field 4 [+2] UInt short_field
In this case, FixedSize.$size_in_bytes
will always be 6
, even if a FixedSize
is placed in a larger field:
struct Envelope: # padded_payload.$size_in_bytes == FixedSize.$size_in_bytes == 6 0 [+8] FixedSize padded_payload
The intrinsic size of a struct
might not be constant:
struct DynamicallySizedField: 0 [+1] UInt length 1 [+length] UInt:8[] payload # $size_in_bytes == 1 + length struct DynamicallyPlacedField: 0 [+1] UInt offset offset [+1] UInt payload # $size_in_bytes == offset + 1 struct OptionalField: 0 [+1] UInt version if version > 3: 1 [+1] UInt optional_field # $size_in_bytes == (version > 3 ? 2 : 1)
If the intrinsic size is dynamic, it can still be read dynamically from a field:
struct Envelope2: 0 [+1] UInt payload_size 1 [+payload_size] DynamicallySizedField payload let padding_bytes = payload_size - payload.$size_in_bytes
$max_size_in_bytes
The $max_size_in_bytes
virtual field is a constant value that is at least as large as the largest possible value for $size_in_bytes
. In most cases, it will exactly equal the largest possible message size, but it is possible to outsmart Emboss's bounds checker.
struct DynamicallySizedStruct: 0 [+1] UInt length 1 [+length] UInt:8[] payload struct PaddedContainer: 0 [+DynamicallySizedStruct.$max_size_in_bytes] DynamicallySizedStruct s # s will be 256 bytes long.
$min_size_in_bytes
The $min_size_in_bytes
virtual field is a constant value that is no larger than the smallest possible value for $size_in_bytes
. In most cases, it will exactly equal the smallest possible message size, but it is possible to outsmart Emboss's bounds checker.
struct DynamicallySizedStruct: 0 [+1] UInt length 1 [+length] UInt:8[] payload struct PaddedContainer: 0 [+DynamicallySizedStruct.$min_size_in_bytes] DynamicallySizedStruct s # s will be 1 byte long.
enum
An enum
defines a set of named integers.
enum Color: BLACK = 0 RED = 1 GREEN = 2 YELLOW = 3 BLUE = 4 MAGENTA = 5 CYAN = 6 WHITE = 7 struct PaletteEntry: 0 [+1] UInt id 1 [+1] Color color
Enum values are always read the same way as Int
or UInt
-- that is, as an unsigned integer or as a 2's-complement signed integer, depending on whether the enum
contains any negative values or not.
Enum values do not have to be contiguous, and may repeat:
enum Baud: B300 = 300 B600 = 600 B1200 = 1200 STANDARD = 1200
All values in a single enum
must either be between -9223372036854775808 (-2^63) and 9223372036854775807 (2^(63)-1), inclusive, or between 0 and 18446744073709551615 (2^(64)-1), inclusive.
It is valid to have an enum
field that is too small to contain some values in the enum
:
enum LittleAndBig: LITTLE = 1 BIG = 0x1_0000_0000 struct LittleOnly: 0 [+1] LittleAndBig:8 little_only # Too small to hold LittleAndBig.BIG
enum
It is possible to provide an enum definition directly in a field definition in a struct
or bits
:
struct TurnSpecification: 0 [+1] UInt degrees 1 [+1] enum direction: LEFT = 0 RIGHT = 1
This example creates a nested enum
TurnSpecification.Direction
, exactly as if it were written:
struct TurnSpecification: enum Direction: LEFT = 0 RIGHT = 1 0 [+1] UInt degrees 1 [+1] Direction direction
This can be useful when a particular enum
is short and only used in one place.
bits
A bits
defines a view of an ordered sequence of bits. Each field is a view of some particular subsequence of the bits
‘s bits, whose interpretation is determined by the field’s type.
The structure of a bits
definition is very similar to a struct
, except that a struct
provides a structured view of bytes, where a bits
provides a structured view of bits. Fields in a bits
must have bit-oriented types (such as other bits
, UInt
, Bcd
, Flag
). Byte-oriented types, such as struct
s, may not be embedded in a bits
.
For example:
bits ControlRegister: -- The `ControlRegister` holds basic control values. 4 [+12] UInt horizontal_start_offset -- The number of pixel clock ticks to wait after the start of a line -- before starting to draw pixel data. 3 [+1] Flag horizontal_overscan_disable -- If set, the electron gun will be disabled during the overscan period, -- otherwise the overscan color will be used. 0 [+3] UInt horizontal_overscan_color -- The palette index of the overscan color to use. struct RegisterPage: -- The registers of the BGA (Bogus Graphics Array) card. 0 [+2] ControlRegister control_register [byte_order: "LittleEndian"]
The first line introduces the bits
and gives it a name. This name may be used in field definitions to specify that the field has a structured type, and is used in the generated code.
For example, to write a horizontal_overscan_color
of 7 to a pair of bytes in C++, you would use:
// vector<uint8_t> bytes; auto register_page_view = RegisterPageWriter(&bytes[0], bytes.size()); register_page_view.control_register().horizontal_overscan_color().Write(7);
Similar to struct
, each field starts with a bit range (4 [+12]
) that indicates which bits it covers. For example, the horizontal_overscan_disable
field only covers bit 3. Bit 0 always corresponds to the lowest-order bit the bitfield; that is, if a UInt
covers the same bits as the bits
construct, then bit 0 in the bits
will be the same as the UInt
mod 2. This is often, but not always, how bits are numbered in protocol specifications.
After the field‘s location is the field’s type. The type determines how the field's bits are interpreted: typical choices are UInt
(for unsigned integers), Flag
(for boolean flags), and enum
s. Other bits
may also be used, as well as any external
types declared with [addressable_unit_size: 1]
.
Fields may have attributes and documentation, just like any other Emboss construct.
In generated code, reading or writing any field of a bits
construct will cause the entire field to be read or written -- something to keep in mind when reading or writing a memory-mapped register space.
A bits
will have $size_in_bits
, $max_size_in_bits
, and $min_size_in_bits
virtual fields automatically generated. These virtual fields can be referenced inside the Emboss language just like any other virtual field:
bits Inner: 0 [+4] UInt field_a 4 [+4] UInt field_b struct Outer: 0 [+1] UInt message_type if message_type == 4: 4 [+Inner.$size_in_bits] Inner payload
$size_in_bits
Like a struct
, an Emboss bits
has an intrinsic size, which is the size required to hold every field in the bits
, regardless of how many bits are in the buffer that backs the bits
. For example:
bits FixedSize: 0 [+3] UInt long_field 3 [+1] Flag short_field
In this case, FixedSize.$size_in_bits
will always be 4
, even if a FixedSize
is placed in a larger field:
struct Envelope: # padded_payload.$size_in_bits == FixedSize.$size_in_bits == 4 0 [+8] FixedSize padded_payload
Unlike struct
s, the size of bits
must known at compile time; there are no dynamic $size_in_bits
fields.
$max_size_in_bits
Since bits
must be fixed size, the $max_size_in_bits
field has the same value as $size_in_bits
. It is provided for consistency with $max_size_in_bytes
.
$min_size_in_bits
Since bits
must be fixed size, the $min_size_in_bits
field has the same value as $size_in_bits
. It is provided for consistency with $min_size_in_bytes
.
bits
It is possible to use an anonymous bits
definition directly in a struct
; for example:
struct Message: [$default byte_order: "BigEndian"] 0 [+4] UInt message_length 4 [+4] bits: 0 [+1] Flag incoming 1 [+1] Flag last_fragment 2 [+4] UInt scale_factor 31 [+1] Flag error
In this case, the fields of the bits
will be treated as though they are fields of the outer struct.
bits
Like enum
s, it is also possible to define a named bits
inline in a struct
or bits
. For example:
struct Message: [$default byte_order: "BigEndian"] 0 [+4] UInt message_length 4 [+4] bits payload: 0 [+1] Flag incoming 1 [+1] Flag last_fragment 2 [+4] UInt scale_factor 31 [+1] Flag error
This is equivalent to:
struct Message: [$default byte_order: "BigEndian"] bits Payload: 0 [+1] Flag incoming 1 [+1] Flag last_fragment 2 [+4] UInt scale_factor 31 [+1] Flag error 0 [+4] UInt message_length 4 [+4] Payload payload
This can be useful as a way to group related fields together.
external
An external
type is used when a type cannot be defined in Emboss itself; instead, external code must be provided to manipulate the type.
Emboss's built-in types, such as UInt
, Bcd
, and Flag
, are defined this way in a special file called the prelude. For example, UInt
is defined as:
external UInt: -- UInt is an automatically-sized unsigned integer. [type_requires: $is_statically_sized && 1 <= $static_size_in_bits <= 64] [is_integer: true] [addressable_unit_size: 1]
external
types are an unstable feature. Contact emboss-dev
if you would like to add your own external
s.
Emboss has a built-in module called the Prelude, which contains types that are automatically usable from any module. In particular, types like Int
and UInt
are defined in the Prelude.
The Prelude is (more or less) a standard Emboss file, called prelude.emb
, that is embedded in the Emboss compiler.
UInt
A UInt
is an unsigned integer. UInt
can be anywhere from 1 to 64 bits in size, and may be used both in struct
s and in bits
. UInt
fields may be referenced in integer expressions.
Int
An Int
is a signed two's-complement integer. Int
can be anywhere from 1 to 64 bits in size, and may be used both in struct
s and in bits
. Int
fields may be referenced in integer expressions.
Bcd
(Note: Bcd
is subject to change.)
A Bcd
is an unsigned binary-coded decimal integer. Bcd
can be anywhere from 1 to 64 bits in size, and may be used both in struct
s and in bits
. Bcd
fields may be referenced in integer expressions.
When a Bcd
's size is not a multiple of 4 bits, the high-order “digit” is treated as if it were zero-extended to a multiple of 4 bits. For example, a 7-bit Bcd
value can store any number from 0 to 79.
Flag
A Flag
is a 1-bit boolean value. A stored value of 0
means false
, and a stored value of 1
means true
.
Float
A Float
is a floating-point value in an IEEE 754 binaryNN format, where NN is the bit width.
Only 32- and 64-bit Float
s are supported. There are no current plans to support 16- or 128-bit Float
s, nor the nonstandard x86 80-bit Float
s.
IEEE 754 does not specify which NaN bit patterns are signalling NaNs and which are quiet NaNs, and thus Emboss also does not specify which NaNs are which. This means that a quiet NaN written through an Emboss view one system could be read out as a signalling NaN through an Emboss view on a different system. If this is a concern, the application must explicitly check for NaN before doing arithmetic on any floating-point value read from a Float
field.
All names in Emboss must be ASCII, for compatibility with languages such as C and C++ that do not support Unicode identifiers.
Type names in Emboss are always CamelCase
. They must start with a capital letter, contain at least one lower-case letter, and contain only letters and digits. They are required to match the regex [A-Z][a-zA-Z0-9]*[a-z][a-zA-Z0-9]*
Imported module names and field names are always snake_case
. They must start with a lower-case letter, and may only contain lower-case letters, numbers, and underscore. They must match the regex [a-z][a-z_0-9]*
.
Enum value names are always SHOUTY_CASE
. They must start with a capital letter, may only contain capital letters, numbers, and underscore, and must be at least two characters long. They must match the regex [A-Z][A-Z_0-9]*[A-Z_][A-Z_0-9]*
.
Additionally, names that are used as keywords in common programming languages are disallowed. A complete list can be found in the Grammar Reference.
Emboss primary expressions are field names (like field
or field.subfield
), numeric constants (like 9
or 0x1_0000_0000
), enum value names (like Enum.VALUE
), and the boolean constants true
and false
.
Subfields may be specified using .
; e.g., foo.bar
references the bar
subfield of the foo
field. Emboss parses .
before any expressions: unlike many languages, something like (foo).bar
is a syntax error in Emboss.
Enum values generally must be qualified by their type; e.g., Color.RED
rather than just RED
. Enums defined in other modules must use the imported module name, as in styles.Color.RED
.
Note: Emboss currently has a relatively limited set of operators because operators have been implemented as needed. If you could use an operator that is not on the list, email emboss-dev@
, and we'll see about adding it.
Emboss operators have the following precedence (tightest binding to loosest binding):
()
$max()
$present()
$upper_bound()
$lower_bound()
+
and -
(see note 1)*
+
-
<
>
==
!=
>=
<=
(see note 2)&&
||
(see note 3)?:
(see note 4)Only one unary +
or -
may be applied to an expression without parentheses. These expressions are valid:
-5 +6 -(-x)
These are not:
- -5 -+5 + +5 +-5
The relational operators may be chained like so:
10 <= x < 50 # 10 <= x && x < 50 10 <= x == y < 50 # 10 <= x && x == y && y < 50 100 > y >= 2 # 100 > y && y >= 2 x == y == 15 # x == y && y == 15
These are not:
10 < x > 50 10 < x == y >= z x == y >= z <= 50
If one specifically wants to compare the result of a comparison, parentheses must be used:
(x > 15) == (y > 15) (x > 15) == true
The !=
operator may not be chained.
A chain may contain either <
, <=
, and/or ==
, or >
, >=
, and/or ==
. Greater-than comparisons may not be mixed with less-than comparisons.
The boolean logical operators have the same precedence, but may not be mixed without parentheses. The following are allowed:
x && y && z x || y || z (x || y) && z x || (y && z)
The following are not allowed:
x || y && z x && y || z
The choice operator ?:
may not be chained without parentheses. These are OK:
q ? x : (r ? y : z) q ? (r ? x : y) : z
This is not:
q ? x : r ? y : z # Is this `(q?x:r)?y:z` or `q?x:(r?y:z)`? q ? r ? x : y : z # Technically unambiguous, but visually confusing
()
Parentheses are used to override precedence. The subexpression inside the parentheses will be evaluated as a unit:
3 * 4 + 5 == 17 3 * (4 + 5) == 27
The value inside the parentheses can have any type; the value of the resulting expression will have the same type.
$present()
The $present()
function takes a field as an argument, and returns true
if the field is present in its structure.
struct PresentExample: 0 [+1] UInt x if false: 1 [+1] UInt y if x > 10: 2 [+1] UInt z if $present(x): # Always true 0 [+1] Int x2 if $present(y): # Always false 1 [+1] Int y2 if $present(z): # Equivalent to `if x > 10` 2 [+1] Int z2
$present()
takes exactly one argument.
The argument to $present()
must be a reference to a field. It can be a nested reference, like $present(x.y.z.q.r)
. The type of the field does not matter.
$present()
returns a boolean.
$max()
The $max()
function returns the maximum value out of its arguments:
$max(1) == 1 $max(-10, -5) == -5 $max(1, 2, 3, 4, 5, 6, 7, 8, 9, 10) == 10
$max()
requires at least one argument. There is no explicit limit on the number of arguments, but at some point the Emboss compiler will run out of memory.
All arguments to $max()
must be integers, and it returns an integer.
$upper_bound()
The $upper_bound()
function returns a value that is at least as high as the maximum possible value of its argument:
$upper_bound(1) == 1 $upper_bound(-10) == -10 $upper_bound(foo) == 255 # If foo is UInt:8 $upper_bound($max(foo, 500)) == 500 # If foo is UInt:8
Generally, $upper_bound()
will return a tight bound, but it is possible to outsmart Emboss's bounds checker.
$upper_bound()
takes a single integer argument, and returns a single integer argument.
$lower_bound()
The $lower_bound()
function returns a value that is no greater than the minimum possible value of its argument:
$lower_bound(1) == 1 $lower_bound(-10) == -10 $lower_bound(foo) == -127 # If foo is Int:8 $lower_bound($min(foo, -500)) == -500 # If foo is Int:8
Generally, $lower_bound()
will return a tight bound, but it is possible to outsmart Emboss's bounds checker.
$lower_bound()
takes a single integer argument, and returns a single integer argument.
+
and -
The unary +
operator returns its argument unchanged.
The unary -
operator subtracts its argument from 0:
3 * -4 == 0 - 12 -(3 * 4) == -12
Unary +
and -
require an integer argument, and return an integer result.
*
*
is the multiplication operator:
3 * 4 == 12 10 * 10 == 100
The *
operator requires two integer arguments, and returns an integer.
+
and -
+
and -
are the addition and subtraction operators, respectively:
3 + 4 == 7 3 - 4 == -1
The +
and -
operators require two integer arguments, and return an integer result.
==
and !=
The ==
operator returns true
if its arguments are equal, and false
if not.
The !=
operator returns false
if its arguments are equal, and true
if not.
Both operators take two boolean arguments, two integer arguments, or two arguments of the same enum type, and return a boolean result.
<
, <=
, >
, and >=
The <
operator returns true
if its first argument is numerically less than its second argument.
The >
operator returns true
if its first argument is numerically greater than its second argument.
The <=
operator returns true
if its first argument is numerically less than or equal to its second argument.
The >=
operator returns true
if its first argument is numerically greater than or equal to its second argument.
All of these operators take two integer arguments, and return a boolean value.
&&
and ||
The &&
operator returns false
if either of its arguments are false
, even if the other argument cannot be computed. &&
returns true
if both arguments are true
.
The ||
operator returns true
if either of its arguments are true
, even if the other argument cannot be computed. ||
returns false
if both arguments are false
.
The &&
and ||
operators require two boolean arguments, and return a boolean result.
?:
The ?:
operator, used like condition
?
if_true
:
if_false
, returns if_true
if condition
is true
, otherwise if_false
.
Other than having stricter type requirements for its arguments, it behaves like the C, C++, Java, JavaScript, C#, etc. conditional operator ?:
(sometimes called the “ternary operator”).
The ?:
operator's condition
argument must be a boolean, and the if_true
and if_false
arguments must have the same type. It returns the same type as if_true
and if_false
.
Numeric constants in Emboss may be written in decimal, hexadecimal, or binary format:
12 # The decimal value of 6 + 6. 012 # The same value; NOT interpreted as octal. 0xc # The same value, written in hexadecimal. 0xC # Hex digits may be written in capital letters. # Note that the 'x' must be lower-case: 0XC is not allowed. 0b1100 # The same value, in binary.
Decimal numbers may use _
as a thousands separator:
1_000_000 # 1e6 123_456_789
Hexadecimal and binary numbers may use _
as a separator every 4 or 8 digits:
0x1234_5678_9abc_def0 0x12345678_9abcdef0 0b1010_0101_1010_0101 0b10100101_10100101
If separators are used, they must be thousands separators (for decimal numbers) or 4- or 8-digit separators (for binary or hexadecimal numbers); _
may not be placed arbitrarily. Binary and hexadecimal numbers must be consistent about whether they use 4- or 8-digit separators; they cannot be mixed in the same constant:
1000_000 # Not allowed: missing the separator after 1. 1_000_00 # Not allowed: separators must be followed by a multiple # of 3 digits. 0x1234_567 # Not allowed: separators must be followed by a multiple # of 4 or 8 digits. 0x1234_5678_9abcdef0 # Not allowed: cannot mix 4- and 8-digit separators.