# Copyright (c) 2021 Project CHIP Authors
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
# Auto-generated scripts for harness use only, please review before automation. The endpoints and cluster names are currently set to default

name: 36.2.3. [TC-WNCV-2.3] Mode Attribute with server as DUT

PICS:
    - WNCV.S

config:
    nodeId: 0x12344321
    cluster: "Window Covering"
    endpoint: 1

tests:
    - label: "Wait for the commissioned device to be retrieved"
      cluster: "DelayCommands"
      command: "WaitForCommissionee"
      arguments:
          values:
              - name: "nodeId"
                value: nodeId

    ### ------------------------------------------------------
    ### Step 1x -> Check Lift Reversal (If PICS_WNCV.S.M.Reversal)
    ## Set b0
    - label: "1a: TH set the Mode Attribute bit0 of the DUT"
      command: "writeAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Reversal && WNCV.S.A0017"
      arguments:
          value: 0x01

    ## Value of bit2 must be 1b
    - label: "1b: TH reads ConfigStatus attribute from DUT"
      command: "readAttribute"
      attribute: "ConfigStatus"
      PICS: "WNCV.S.M.Reversal && WNCV.S.A0007"
      response:
          constraints:
              minValue: 0x04
              maxValue: 0x7F

    ## Clear b0
    - label: "1c: TH clear the Mode Attribute bit0 of the DUT"
      command: "writeAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Reversal && WNCV.S.A0017"
      arguments:
          value: 0x00

    ## Value of bit2 must be 0b
    - label: "1d: TH reads ConfigStatus attribute from DUT"
      command: "readAttribute"
      attribute: "ConfigStatus"
      PICS: "WNCV.S.M.Reversal && WNCV.S.A0007"
      response:
          constraints:
              minValue: 0x00
              maxValue: 0x7F

    ### ------------------------------------------------------
    ### Step 2x -> Check Calibration mode
    ## Set b1
    - label: "2a: TH set the Mode Attribute bit1 of the DUT"
      command: "writeAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Calibration && WNCV.S.A0017"
      arguments:
          value: 0x02

    ## Value of bitO can be 0b
    - label: "2b: TH reads ConfigStatus attribute from DUT"
      command: "readAttribute"
      attribute: "ConfigStatus"
      PICS: "WNCV.S.M.Calibration && WNCV.S.A0007"
      response:
          saveAs: configStatusValA
          constraints:
              minValue: 0x00
              maxValue: 0x7F

    ## If (ConfigStatus bit0 == 0) Verify DUT responds with FAILURE (value 0x01) status response
    - label:
          "2c: If (ConfigStatus bit0 == 0) TH send DownOrClose command to the
          DUT"
      command: "DownOrClose"
      PICS: "WNCV.S.M.Calibration && WNCV.S.C01.Rsp"
      response:
          error: FAILURE

    ## Clear b1
    - label: "2d: TH clear the Mode Attribute bit1 of the DUT"
      command: "writeAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Calibration && WNCV.S.A0017"
      arguments:
          value: 0x00

    ## Value of bitO must be 1b
    - label: "2e: TH reads ConfigStatus attribute from DUT"
      command: "readAttribute"
      attribute: "ConfigStatus"
      PICS: "WNCV.S.M.Calibration && WNCV.S.A0007"
      response:
          constraints:
              minValue: 0x01
              maxValue: 0x7F

    ## Value of bit1 must be 0b
    - label: "2f: TH reads the Mode Attribute from the DUT"
      command: "readAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Calibration && WNCV.S.A0017"
      response:
          constraints:
              minValue: 0x00
              maxValue: 0x7F

    ## Verify DUT responds with SUCCESS status response
    - label: "2g: TH send DownOrClose command to the DUT"
      command: "DownOrClose"
      PICS: "WNCV.S.M.Calibration && WNCV.S.C01.Rsp"

    ### ------------------------------------------------------
    ### Step 3x -> Check Maintenance mode
    ## Set b2
    - label: "3a: TH set the Mode Attribute bit2 of the DUT"
      command: "writeAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Maintenance && WNCV.S.A0017"
      arguments:
          value: 0x04

    ## If Verify DUT responds with BUSY (value 0x9c) status response
    - label: "3b: TH send DownOrClose command to the DUT"
      command: "DownOrClose"
      PICS: "WNCV.S.M.Maintenance && WNCV.S.C01.Rsp"
      response:
          error: BUSY

    ## Value of bitO must be 0b
    - label: "3c: TH reads ConfigStatus attribute from DUT"
      command: "readAttribute"
      PICS: "WNCV.S.M.Maintenance && WNCV.S.A0007"
      attribute: "ConfigStatus"
      response:
          saveAs: configStatusValB
          constraints:
              minValue: 0x00
              maxValue: 0x7F

    ## Clear b2
    - label: "3d: TH clear the Mode Attribute bit2 of the DUT"
      command: "writeAttribute"
      attribute: "Mode"
      PICS: "WNCV.S.M.Maintenance && WNCV.S.A0017"
      arguments:
          value: 0x00

    ## Verify DUT responds with SUCCESS status response
    - label: "3e: TH send DownOrClose command to the DUT"
      command: "DownOrClose"
      PICS: "WNCV.S.M.Maintenance && WNCV.S.C01.Rsp"

    ## Value of bitO must be 1b
    - label: "3f: TH reads ConfigStatus attribute from DUT"
      command: "readAttribute"
      attribute: "ConfigStatus"
      PICS: "WNCV.S.M.Maintenance && WNCV.S.A0007"
      response:
          constraints:
              minValue: 0x01
              maxValue: 0x7F