tree: 1d5ff943899280799858380d1f5a7038639125ca [path history] [tgz]
  1. include/
  2. src/
  3. third_party/
  4. .gn
  5. args.gni
  6. BUILD.gn
  7. build_for_wifi_args.gni
  8. build_for_wifi_gnfile.gn
  9. README.md
  10. with_pw_rpc.gni
examples/lock-app/efr32/README.md

Matter EFR32 Lock Example

An example showing the use of CHIP on the Silicon Labs EFR32 MG12 and MG24.

NOTE: Silicon Laboratories now maintains a public matter GitHub repo with frequent releases thoroughly tested and validated. Developers looking to develop matter products with silabs hardware are encouraged to use our latest release with added tools and documentation. Silabs Matter Github

Introduction

The EFR32 lock example provides a baseline demonstration of a door lock control device, built using Matter and the Silicon Labs gecko SDK. It can be controlled by a Chip controller over an Openthread or Wifi network..

The EFR32 device can be commissioned over Bluetooth Low Energy where the device and the Chip controller will exchange security information with the Rendez-vous procedure. If using Thread, Thread Network credentials are then provided to the EFR32 device which will then join the Thread network.

If the LCD is enabled, the LCD on the Silabs WSTK shows a QR Code containing the needed commissioning information for the BLE connection and starting the Rendez-vous procedure.

The lighting example is intended to serve both as a means to explore the workings of Matter as well as a template for creating real products based on the Silicon Labs platform.

Building

  • Download the Simplicity Commander command line tool, and ensure that commander is your shell search path. (For Mac OS X, commander is located inside Commander.app/Contents/MacOS/.)

  • Download and install a suitable ARM gcc tool chain: GNU Arm Embedded Toolchain 9-2019-q4-major

  • Install some additional tools(likely already present for CHIP developers):

Linux

sudo apt-get install git ninja-build

Mac OS X

brew install ninja
  • Supported hardware:

    • For the latest supported hardware please refer to the Hardware Requirements in the Silicon Labs Matter Github Repo

    MG12 boards:

    • BRD4161A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@19dBm
    • BRD4162A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4163A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm, 868MHz@19dBm
    • BRD4164A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@19dBm
    • BRD4166A / SLTB004A / Thunderboard Sense 2 / 2.4GHz@10dBm
    • BRD4170A / SLWSTK6000B / Multiband Wireless Starter Kit / 2.4GHz@19dBm, 915MHz@19dBm
    • BRD4304A / SLWSTK6000B / MGM12P Module / 2.4GHz@19dBm

    MG21 boards: Currently not supported due to RAM limitation.

    • BRD4180A / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@20dBm

    MG24 boards :

    • BRD2601B / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD2703A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4186A / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4186C / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4187A / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@20dBm
    • BRD4187C / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@20dBm

    MG12 boards:

    • BRD4161A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@19dBm
    • BRD4162A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4163A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm, 868MHz@19dBm
    • BRD4164A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@19dBm
    • BRD4166A / SLTB004A / Thunderboard Sense 2 / 2.4GHz@10dBm
    • BRD4170A / SLWSTK6000B / Multiband Wireless Starter Kit / 2.4GHz@19dBm, 915MHz@19dBm
    • BRD4304A / SLWSTK6000B / MGM12P Module / 2.4GHz@19dBm

    MG21 boards: Currently not supported due to RAM limitation.

    • BRD4180A / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@20dBm

    MG24 boards :

    • BRD4162A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4163A / SLWSTK6000B / Wireless Starter Kit / 2.4GHz@10dBm, 868MHz@19dBm
    • BRD4186A / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4186C / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@10dBm
    • BRD4187A / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@20dBm
    • BRD4187C / SLWSTK6006A / Wireless Starter Kit / 2.4GHz@20dBm
  • Build the example application:

      ```
      cd ~/connectedhomeip
      ./scripts/examples/gn_efr32_example.sh ./examples/lock-app/efr32/ ./out/lock_app BRD4161A
      ```
    
  • To delete generated executable, libraries and object files use:

      ```
      $ cd ~/connectedhomeip
      $ rm -rf ./out/
      ```
    

    OR use GN/Ninja directly

      ```
      $ cd ~/connectedhomeip/examples/lock-app/efr32
      $ git submodule update --init
      $ source third_party/connectedhomeip/scripts/activate.sh
      $ export EFR32_BOARD=BRD4161A
      $ gn gen out/debug --args="efr32_sdk_root=\"${EFR32_SDK_ROOT}\" silabs_board=\"${EFR32_BOARD}\""
      $ ninja -C out/debug
      ```
    
  • To delete generated executable, libraries and object files use:

      ```
      $ cd ~/connectedhomeip/examples/lock-app/efr32
      $ rm -rf out/
      ```
    
  • Build the example as Sleepy End Device (SED)

      ```
      $ ./scripts/examples/gn_efr32_example.sh ./examples/lighting-app/efr32/ ./out/lighting-app_SED BRD4161A --sed
      ```
    

    or use gn as previously mentioned but adding the following arguments:

      ```
      $ gn gen out/debug '--args=silabs_board="BRD4161A" enable_sleepy_device=true chip_openthread_ftd=false'
      ```
    
  • Build the example with pigweed RCP

      ```
      $ ./scripts/examples/gn_efr32_example.sh examples/lock-app/efr32/ out/lock_app_rpc BRD4161A 'import("//with_pw_rpc.gni")'
      ```
    

    or use GN/Ninja Directly

      ```
      $ cd ~/connectedhomeip/examples/lock-app/efr32
      $ git submodule update --init
      $ source third_party/connectedhomeip/scripts/activate.sh
      $ export EFR32_BOARD=BRD4161A
      $ gn gen out/debug --args='import("//with_pw_rpc.gni")'
      $ ninja -C out/debug
      ```
    

    Running Pigweed RPC console

For more build options, help is provided when running the build script without arguments

     ```
     ./scripts/examples/gn_efr32_example.sh
     ```

Flashing the Application

  • On the command line:

      ```
      $ cd ~/connectedhomeip/examples/lock-app/efr32
      $ python3 out/debug/chip-efr32-lock-example.flash.py
      ```
    
  • Or with the Ozone debugger, just load the .out file.

Viewing Logging Output

The example application is built to use the SEGGER Real Time Transfer (RTT) facility for log output. RTT is a feature built-in to the J-Link Interface MCU on the WSTK development board. It allows bi-directional communication with an embedded application without the need for a dedicated UART.

Using the RTT facility requires downloading and installing the SEGGER J-Link Software and Documentation Pack (web site).

Alternatively, SEGGER Ozone J-Link debugger can be used to view RTT logs too after flashing the .out file.

  • Install the J-Link software

      ```
      $ cd ~/Downloads
      $ sudo dpkg -i JLink_Linux_V*_x86_64.deb
      ```
    
  • In Linux, grant the logged in user the ability to talk to the development hardware via the linux tty device (/dev/ttyACMx) by adding them to the dialout group.

      ```
      $ sudo usermod -a -G dialout ${USER}
      ```
    

Once the above is complete, log output can be viewed using the JLinkExe tool in combination with JLinkRTTClient as follows:

  • Run the JLinkExe tool with arguments to autoconnect to the WSTK board:

    For MG12 use:

      ```
      $ JLinkExe -device EFR32MG12PXXXF1024 -if JTAG -speed 4000 -autoconnect 1
      ```
    

    For MG21 use:

      ```
      $ JLinkExe -device EFR32MG21AXXXF1024 -if SWD -speed 4000 -autoconnect 1
      ```
    
  • In a second terminal, run the JLinkRTTClient to view logs:

      ```
      $ JLinkRTTClient
      ```
    

Running the Complete Example

  • It is assumed here that you already have an OpenThread border router configured and running. If not see the following guide Openthread_border_router for more information on how to setup a border router on a raspberryPi.

    Take note that the RCP code is available directly through Simplicity Studio 5 under File->New->Project Wizard->Examples->Thread : ot-rcp

  • User interface : LCD The LCD on Silabs WSTK shows a QR Code. This QR Code is be scanned by the CHIP Tool app For the Rendez-vous procedure over BLE

    * On devices that do not have or support the LCD Display like the BRD4166A Thunderboard Sense 2,
      a URL can be found in the RTT logs.
    
      <info  > [SVR] Copy/paste the below URL in a browser to see the QR Code:
      <info  > [SVR] https://project-chip.github.io/connectedhomeip/qrcode.html?data=CH%3AI34NM%20-00%200C9SS0
    

    LED 0 shows the overall state of the device and its connectivity. The following states are possible:

    -   _Short Flash On (50 ms on/950 ms off)_ ; The device is in the
        unprovisioned (unpaired) state and is waiting for a commissioning
        application to connect.
    
    -   _Rapid Even Flashing_ ; (100 ms on/100 ms off)_ &mdash; The device is in the
        unprovisioned state and a commissioning application is connected through
        Bluetooth LE.
    
    -   _Short Flash Off_ ; (950ms on/50ms off)_ &mdash; The device is fully
        provisioned, but does not yet have full Thread network or service
        connectivity.
    
    -   _Solid On_ ; The device is fully provisioned and has full Thread
        network and service connectivity.
    

    LED 1 Simulates the Lock The following states are possible:

    -   _Solid On_ ; Bolt is unlocked
    -   _Blinking_ ; Bolt is moving to the desired state
    -   _Off_ ; Bolt is locked
    

    Push Button 0

    -   _Press and Release_ : Start, or restart, BLE advertisement in fast mode. It will advertise in this mode
        for 30 seconds. The device will then switch to a slower interval advertisement.
        After 15 minutes, the advertisement stops.
    
    -   _Pressed and hold for 6 s_ : Initiates the factory reset of the device.
        Releasing the button within the 6-second window cancels the factory reset
        procedure. **LEDs** blink in unison when the factory reset procedure is
        initiated.
    

    Push Button 1 Toggles the bolt state On/Off

  • You can provision and control the Chip device using the python controller, Chip tool standalone, Android or iOS app

    CHIPTool

Here is some CHIPTool examples:

Pairing with chip-tool:
```
chip-tool pairing ble-thread 1 hex:<operationalDataset> 20202021 3840
```

Set a user:
```
./out/chip-tool doorlock set-user OperationType UserIndex UserName UserUniqueId UserStatus UserType CredentialRule node-id/group-id
./out/chip-tool doorlock set-user 0 1 "mike" 5 1 0 0 1 1 --timedInteractionTimeoutMs 1000
```

Set a credential:
```
./out/chip-tool doorlock set-credential OperationType Credential CredentialData UserIndex UserStatus UserType node-id/group-id
./out/chip-tool doorlock set-credential 0 '{ "credentialType": 1, "credentialIndex": 1 }' "123456" 1 null null 1 1 --timedInteractionTimeoutMs 1000
```

Changing a credential:
```
./out/chip-tool doorlock set-credential OperationType Credential CredentialData UserIndex UserStatus UserType node-id/group-id
./out/chip-tool doorlock set-credential 2 '{ "credentialType": 1, "credentialIndex": 1 }' "123457" 1 null null 1 1 --timedInteractionTimeoutMs 1000
```

Get a user:
```
./out/chip-tool doorlock get-user UserIndex node-id/group-id
./out/chip-tool doorlock get-user 1 1 1
```

Unlock door:
```
./out/chip-tool doorlock unlock-door node-id/group-id
./out/chip-tool doorlock unlock-door 1 1 --timedInteractionTimeoutMs 1000
```

Lock door:
```
./out/chip-tool doorlock lock-door node-id/group-id
./out/chip-tool doorlock lock-door 1 1 --timedInteractionTimeoutMs 1000
```

Notes

  • Depending on your network settings your router might not provide native ipv6 addresses to your devices (Border router / PC). If this is the case, you need to add a static ipv6 addresses on both device and then an ipv6 route to the border router on your PC

#On Border Router: $ sudo ip addr add dev 2002::2/64

#On PC(Linux): $ sudo ip addr add dev 2002::1/64

#Add Ipv6 route on PC(Linux) $ sudo ip route add /64 via 2002::2

Memory settings

While most of the RAM usage in CHIP is static, allowing easier debugging and optimization with symbols analysis, we still need some HEAP for the crypto and OpenThread. Size of the HEAP can be modified by changing the value of the configTOTAL_HEAP_SIZE define inside of the FreeRTOSConfig.h file of this example. Please take note that a HEAP size smaller than 13k can and will cause a Mbedtls failure during the BLE rendez-vous or CASE session

To track memory usage you can set enable_heap_monitoring = true either in the BUILD.gn file or pass it as a build argument to gn. This will print on the RTT console the RAM usage of each individual task and the number of Memory allocation and Free. While this is not extensive monitoring you're welcome to modify examples/platform/efr32/MemMonitoring.cpp to add your own memory tracking code inside the trackAlloc and trackFree function

OTA Software Update

For the description of Software Update process with EFR32 example applications see EFR32 OTA Software Update

Building options

All of Silabs's examples within the Matter repo have all the features enabled by default, as to provide the best end user experience. However some of those features can easily be toggled on or off. Here is a short list of options :

Disabling logging

chip_progress_logging, chip_detail_logging, chip_automation_logging

```
$ ./scripts/examples/gn_efr32_example.sh ./examples/lighting-app/efr32 ./out/lighting-app BRD4164A "chip_detail_logging=false chip_automation_logging=false chip_progress_logging=false"
```

Debug build / release build

is_debug

```
$ ./scripts/examples/gn_efr32_example.sh ./examples/lighting-app/efr32 ./out/lighting-app BRD4164A "is_debug=false"
```

Disabling LCD

show_qr_code

```
$ ./scripts/examples/gn_efr32_example.sh ./examples/lighting-app/efr32 ./out/lighting-app BRD4164A "show_qr_code=false"
```

KVS maximum entry count

kvs_max_entries

```
Set the maximum Kvs entries that can be stored in NVM (Default 75)
Thresholds: 30 <= kvs_max_entries <= 255

$ ./scripts/examples/gn_efr32_example.sh ./examples/lighting-app/efr32 ./out/lighting-app BRD4164A kvs_max_entries=50
```