# Monitoring baud and flash size
CONFIG_ESPTOOLPY_MONITOR_BAUD=115200
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y

# Enable BT
CONFIG_BT_ENABLED=y
CONFIG_BT_NIMBLE_ENABLED=y
CONFIG_BT_NIMBLE_EXT_ADV=n
CONFIG_BT_NIMBLE_HCI_EVT_BUF_SIZE=70
CONFIG_USE_BLE_ONLY_FOR_COMMISSIONING=y

# Disable BT connection reattempt
CONFIG_BT_NIMBLE_ENABLE_CONN_REATTEMPT=n

# BLE sleep
CONFIG_BT_LE_SLEEP_ENABLE=y
CONFIG_BT_LE_LP_CLK_SRC_MAIN_XTAL=y

# Disable external 32K crystal
CONFIG_RTC_CLK_SRC_EXT_CRYS=n

# FreeRTOS should use legacy API
CONFIG_FREERTOS_ENABLE_BACKWARD_COMPATIBILITY=y

# FreeRTOS config for light sleep
CONFIG_FREERTOS_HZ=1000
CONFIG_FREERTOS_USE_TICKLESS_IDLE=y

# FreeRTOS config for light sleep
CONFIG_FREERTOS_HZ=1000
CONFIG_FREERTOS_USE_TICKLESS_IDLE=y

# Enable OpenThread
CONFIG_OPENTHREAD_ENABLED=y
CONFIG_OPENTHREAD_SRP_CLIENT=y
CONFIG_OPENTHREAD_DNS_CLIENT=y
CONFIG_OPENTHREAD_LOG_LEVEL_DYNAMIC=n
CONFIG_OPENTHREAD_LOG_LEVEL_NOTE=y
CONFIG_OPENTHREAD_CLI=n

# Use OpenThread MTD
CONFIG_OPENTHREAD_MTD=y

# Enable IEEE 802.15.4 sleep
CONFIG_IEEE802154_SLEEP_ENABLE=y

# Use a custom partition table
CONFIG_PARTITION_TABLE_CUSTOM=y
CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions.csv"
CONFIG_PARTITION_TABLE_OFFSET=0xC000

# Disable STA and AP for ESP32H2
CONFIG_ENABLE_WIFI_STATION=n
CONFIG_ENABLE_WIFI_AP=n
CONFIG_ESP_WIFI_SOFTAP_SUPPORT=n

# Disable chip shell
CONFIG_ENABLE_CHIP_SHELL=n

# Enable DS Peripheral
CONFIG_ESP_SECURE_CERT_DS_PERIPHERAL=y

# Enable HKDF in mbedtls
CONFIG_MBEDTLS_HKDF_C=y

# Disable hardware acceleration
CONFIG_MBEDTLS_HARDWARE_AES=n
CONFIG_MBEDTLS_HARDWARE_MPI=n
CONFIG_MBEDTLS_HARDWARE_SHA=n
CONFIG_MBEDTLS_HARDWARE_ECC=n
CONFIG_MBEDTLS_HARDWARE_ECDSA_VERIFY=n
CONFIG_MBEDTLS_SSL_PROTO_DTLS=y

# LwIP config for OpenThread
CONFIG_LWIP_IPV6_NUM_ADDRESSES=8
CONFIG_LWIP_MULTICAST_PING=y

# LwIP config for light sleep
CONFIG_LWIP_ND6=n
CONFIG_LWIP_IPV4=n
CONFIG_DISABLE_IPV4=y

# Disable lwip ipv6 autoconfig for Thread device
CONFIG_LWIP_IPV6_AUTOCONFIG=n

# Use platform mDNS
CONFIG_USE_MINIMAL_MDNS=n
CONFIG_ENABLE_EXTENDED_DISCOVERY=y

# Enable power management
CONFIG_PM_ENABLE=y
CONFIG_PM_DFS_INIT_AUTO=y
CONFIG_PM_POWER_DOWN_PERIPHERAL_IN_LIGHT_SLEEP=y
CONFIG_ESP_SLEEP_POWER_DOWN_FLASH=y

# ICD configurations
CONFIG_ENABLE_ICD_SERVER=y
CONFIG_ICD_FAST_POLL_INTERVAL_MS=500
CONFIG_ICD_SLOW_POLL_INTERVAL_MS=20000
CONFIG_ICD_IDLE_MODE_INTERVAL_SEC=600
CONFIG_ICD_ACTIVE_MODE_INTERVAL_MS=0
CONFIG_ICD_ACTIVE_MODE_THRESHOLD_MS=5000
CONFIG_ENABLE_ICD_LIT=y
CONFIG_ENABLE_ICD_CIP=y