# Copyright (c) 2021 Project CHIP Authors
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.

# !!!!!!!!!! DO NOT RUN IN CI - ONLY USED IN MANUAL GROUP MESSAGING DEMONSTRATION !!!!!!!!!!

# This test file is used in the group messaging demonstration to configure light-apps
# Run this test on a commisionned device to add it to the group.
# This file is used in tandem with TestGroupDemoCommand that sends the actual commands.
#
# To run this test file : chip-tool tests TestGroupDemoConfig <nodeid>
#
# Full test procedure :
#   chip-tool tests TestGroupDemoConfig <nodeid>  - Run this command for every light app nodeid that will be used for the demonstration
#   chip-tool tests TestGroupDemoCommand <nodeid>
name: Group Messaging Demo - Configuration

config:
    nodeId: 0x12344321
    cluster: "Groups"
    endpoint: 0

tests:
    - label: "Wait for the commissioned device to be retrieved"
      cluster: "DelayCommands"
      command: "WaitForCommissionee"
      arguments:
          values:
              - name: "nodeId"
                value: nodeId

    - label: "Add Group 1 - endpoint 1"
      command: "AddGroup"
      endpoint: 1
      arguments:
          values:
              - name: "groupId"
                value: 0x0101
              - name: "groupName"
                value: "Group #1"
      response:
          values:
              - name: "status"
                value: 0
              - name: "groupId"
                value: 0x0101

    - label: "KeySet Write 1"
      cluster: "Group Key Management"
      command: "KeySetWrite"
      arguments:
          values:
              - name: "GroupKeySet"
                value: {
                        GroupKeySetID: 0x01a1,
                        #  TODO Revert this once MCSP is implemented
                        # GroupKeySecurityPolicy: 1,
                        GroupKeySecurityPolicy: 0, # 0 => TrustFirst
                        EpochKey0: "\xa0\xa1\xa2\xa3\xa4\xa5\xa6\xa7\xa8\xa9\xaa\xab\xac\xad\xae\xaf",
                        EpochStartTime0: 1110000,
                        EpochKey1: "\xb0\xb1\xb2\xb3\xb4\xb5\xb6\xb7\xb8\xb9\xba\xbb\xbc\xbd\xbe\xbf",
                        EpochStartTime1: 1110001,
                        EpochKey2: "\xc0\xc1\xc2\xc3\xc4\xc5\xc6\xc7\xc8\xc9\xca\xcb\xcc\xcd\xce\xcf",
                        EpochStartTime2: 1110002,
                    }

    - label: "Map Group Key Set to group ID on a given fabric"
      cluster: "Group Key Management"
      command: "writeAttribute"
      attribute: "GroupKeyMap"
      arguments:
          value: [{ FabricIndex: 1, GroupId: 0x0101, GroupKeySetID: 0x01a1 }]

    - label: "Install ACLs for test"
      cluster: "Access Control"
      command: "writeAttribute"
      attribute: "ACL"
      arguments:
          value: [
                  # Any CASE can admin
                  {
                      FabricIndex: 1,
                      Privilege: 5,
                      AuthMode: 2,
                      Subjects: null,
                      Targets: null,
                  },
                  # These groups can operate
                  {
                      FabricIndex: 1,
                      Privilege: 3,
                      AuthMode: 3,
                      Subjects: [0x0101],
                      Targets: null,
                  },
              ]