Some examples for the development kits from Nordic Semiconductor support over-the-air (OTA) Device Firmware Upgrade (DFU) using one of the following protocols:
NOTE: The procedure presented below requires that you have OpenThread Border Router (OTBR) set up either in Docker or on a Raspberry Pi. Read Setup OpenThread Border Router on Raspberry Pi to learn how to install the OTBR on a Raspberry Pi.
The DFU over Matter involves two kinds of nodes:
In the procedure described below, the OTA Provider will be a Linux application and the example running on the Nordic Semiconductor's board will work as the OTA Requestor.
To test the DFU over Matter, you need to complete the following steps:
Navigate to the CHIP root directory.
Build the OTA Provider application for Linux:
scripts/examples/gn_build_example.sh examples/ota-provider-app/linux out/provider chip_config_network_layer_ble=false
Build chip-tool for Linux:
scripts/examples/gn_build_example.sh examples/chip-tool out/chiptool 'chip_mdns="platform"'
Run OTA Provider application with matter.ota replaced with the path to the Matter OTA image which you wish to provide to the Matter device. Note that the Matter OTA image is, by default, generated at zephyr/matter.ota in the example's build directory:
$ out/provider/chip-ota-provider-app -f matter.ota
Keep the application running and use another terminal for the remaining steps.
Commission the OTA Provider into the Matter network using Node ID 1:
./out/chiptool/chip-tool pairing onnetwork 1 20202021
Use the OTBR web interface to form a new Thread network using the default network settings.
Commission the Matter device into the same Matter network using Node ID 2. The parameter starting with the hex: prefix is the Thread network's Active Operational Dataset. It can be retrieved from the OTBR in case you have changed the default network settings when forming the network.
./out/chiptool/chip-tool pairing ble-thread 2 hex:000300000f02081111111122222222051000112233445566778899aabbccddeeff01021234 20202021 3840
Configure the Matter device with the default OTA Provider by running the following command (the last two arguments are Requestor Node ID and Requestor Endpoint ID, respectively):
./out/chiptool/chip-tool otasoftwareupdaterequestor write default-ota-providers '[{"fabricIndex": 1, "providerNodeID": 1, "endpoint": 0}]' 2 0
Configure the OTA Provider with the access control list (ACL) that grants Operate privileges to all nodes in the fabric. This is necessary to allow the nodes to send cluster commands to the OTA Provider:
./out/chiptool/chip-tool accesscontrol write acl '[{"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [112233], "targets": null}, {"fabricIndex": 1, "privilege": 3, "authMode": 2, "subjects": null, "targets": null}]' 1 0
Initiate the DFU procedure in one of the following ways:
If you have built the device firmware with -DCONFIG_CHIP_LIB_SHELL=y option, which enables Matter shell commands, run the following command on the device shell:
matter ota query
Otherwise, use chip-tool to send the Announce OTA Provider command to the device (the numeric arguments are Provider Node ID, Provider Vendor ID, Announcement Reason, Provider Endpoint ID, Requestor Node ID and Requestor Endpoint ID, respectively):
./out/chiptool/chip-tool otasoftwareupdaterequestor announce-ota-provider 1 0 0 0 2 0
Once the device is made aware of the OTA Provider node, it automatically queries the OTA Provider for a new firmware image.
When the firmware image download is complete, the device is automatically rebooted to apply the update.
To upgrade your device firmware over Bluetooth LE using a smartphone, complete the following steps:
Install one of the following applications on your smartphone:
Push the appropriate button on the device to enable the software update functionality (if it is not enabled by default) and start the Bluetooth LE advertising of the SMP service. See the user interface section in the example documentation to check the button number.
Push the appropriate button on the device to start the Bluetooth LE advertising. See the user interface section in the example documentation to check the button number.
Follow the instructions about downloading the new image to a device on the FOTA upgrades page in the nRF Connect SDK documentation.
To upgrade your device firmware over Bluetooth LE, you can use the PC command line tool provided by the mcumgr project.
IMPORTANT:
The mcumgr tool using Bluetooth LE is available only for Linux and macOS systems. On Windows, there is no support for Device Firmware Upgrade over Bluetooth LE yet.
It might not be possible to connect to the nRF device when using the mcumgr on Linux with the built-in Bluetooth LE adapter. In such cases, you can use Zephyr‘s Bluetooth HCI USB sample and program it to a Nordic Semiconductor’s development kit to form an external Bluetooth LE adapter. For example, to build the sample for the nRF52840 DK, use the following command:
cd zephyr/samples/bluetooth/hci_usb && west build -b nrf52840dk_nrf52840 -- -DCONFIG_BT_LL_SW_SPLIT=y
Complete the following steps to perform DFU using mcumgr:
NOTE: In all of the commands listed in the following steps, replace
ble-hci-numberwith the Bluetooth hci integer value (for example,0) andble-device-namewith the Matter device name advertised over Bluetooth LE (for example,MatterLock).
Install the tool by following the mcumgr command line tool installation instructions.
Push the appropriate button on the device to enable the software update functionality (if it is not enabled by default) and start the Bluetooth LE advertising of SMP service. See the user interface section in the example documentation to check the button number.
Observe that the LED on the device is flashing (short flash on), which means that the Bluetooth LE advertising has started. See the user interface section in the example documentation to check the LED number.
Upload the application firmware image to the device by running the following command in your example directory:
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' image upload build/zephyr/app_update.bin -n 0 -w 1
The operation can take a few minutes. Wait until the progress bar reaches 100%.
Obtain the list of images present in the device memory by running following command:
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' image list
The displayed output contains the old image in slot 0 that is currently active and the new image in slot 1, which is not active yet (flags field empty):
Images:
image=0 slot=0
version: 0.0.0
bootable: true
flags: active confirmed
hash: 7bb0e909a846e833465cbb44c581cf045413a5446c6953a30a3dcc2c3ad51764
image=0 slot=1
version: 0.0.0
bootable: true
flags:
hash: cbd58fc3821e749d3abfb00b3069f98c078824735f1b2a333e8a1579971e7de1
Split status: N/A (0)
Swap the firmware images by calling the following method with image-hash replaced by the image present in the slot 1 hash (for example, cbd58fc3821e749d3abfb00b3069f98c078824735f1b2a333e8a1579971e7de1):
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' image test image-hash
You can observe that the flags: field in the image for slot 1 changes value to pending:
Images:
image=0 slot=0
version: 0.0.0
bootable: true
flags: active confirmed
hash: 7bb0e909a846e833465cbb44c581cf045413a5446c6953a30a3dcc2c3ad51764
image=0 slot=1
version: 0.0.0
bootable: true
flags: pending
hash: cbd58fc3821e749d3abfb00b3069f98c078824735f1b2a333e8a1579971e7de1
Split status: N/A (0)
If you are using the nRF5340DK board, which supports multi-image device firmware upgrade, complete the following substeps. If you are not using one, go straight to the step 8.
a. Upload the network core firmware image to the device by running the following command in your example directory:
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' image upload build/zephyr/net_core_app_update.bin -n 1 -w 1
The operation can take a few minutes. Wait until the progress bar reaches 100%.
b. Obtain the list of images present in the device memory by running following command:
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' image list
The displayed output contains the old application image in slot 0 that is currently active, the new application image in slot 1 in pending state, and the new network image which is in slot 1 and not active yet (flags field empty):
Images:
image=0 slot=0
version: 0.0.0
bootable: true
flags: active confirmed
hash: 7bb0e909a846e833465cbb44c581cf045413a5446c6953a30a3dcc2c3ad51764
image=0 slot=1
version: 0.0.0
bootable: true
flags: pending
hash: cbd58fc3821e749d3abfb00b3069f98c078824735f1b2a333e8a1579971e7de1
image=1 slot=1
version: 0.0.0
bootable: true
flags:
hash: d9e31e73cb7a959c26411250c2b3028f3510ae88a4549ae3f2f097c3e7530f48
Split status: N/A (0)
c. Swap the firmware images by calling the following method with image-hash replaced by the image present in the slot 1 hash (for example, d9e31e73cb7a959c26411250c2b3028f3510ae88a4549ae3f2f097c3e7530f48):
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' image test image-hash
You can observe that the flags: field in the image for slot 1 changes value to pending:
Images:
image=0 slot=0
version: 0.0.0
bootable: true
flags: active confirmed
hash: 7bb0e909a846e833465cbb44c581cf045413a5446c6953a30a3dcc2c3ad51764
image=0 slot=1
version: 0.0.0
bootable: true
flags: pending
hash: cbd58fc3821e749d3abfb00b3069f98c078824735f1b2a333e8a1579971e7de1
image=1 slot=1
version: 0.0.0
bootable: true
flags: pending
hash: d9e31e73cb7a959c26411250c2b3028f3510ae88a4549ae3f2f097c3e7530f48
Split status: N/A (0)
Reset the device with the following command to let the bootloader swap images:
sudo mcumgr --conntype ble --hci ble-hci-number --connstring peer_name='ble-device-name' reset
The device is reset and the following notifications appear in its console:
*** Booting Zephyr OS build zephyr-v2.5.0-1101-ga9d3aef65424 *** I: Starting bootloader I: Primary image: magic=good, swap_type=0x2, copy_done=0x1, image_ok=0x1 I: Secondary image: magic=good, swap_type=0x2, copy_done=0x3, image_ok=0x3 I: Boot source: none I: Swap type: test
Swapping operation can take some time, and after it completes, the new firmware is booted.
Visit the mcumgr image management section to get familiar with all image management commands supported by the tool.