Matter K32W1 Lighting Example Application

Matter K32W1 Lighting Example demonstrates how to remotely control a light bulb. The light bulb is simulated using one of the LEDs from the expansion board. It uses buttons to test turn on/turn off of the light bulb. You can use this example as a reference for creating your own application.

The example is based on Matter and the NXP K32W1 SDK, and supports remote access and control of a light bulb over a low-power, 802.15.4 Thread network.

The example behaves as a Matter accessory, that is a device that can be paired into an existing Matter network and can be controlled by this network.

• Matter K32W1 Lighting Example Application
• Introduction
  • Bluetooth LE Advertising
  • Bluetooth LE Rendezvous
• Device UI
• Building
  • SMU2
  • LED PWM
• Manufacturing data
• Flashing
  • Flashing the NBU image
  • Flashing the host image
• Debugging
• OTA
  • Convert srec into sb3 file
  • Convert sb3 into ota file
  • Running OTA
  • Known issues
• Running RPC console

Introduction

The K32W1 lighting example application provides a working demonstration of a light bulb device, built using the Matter codebase and the NXP K32W1 SDK. The example supports remote access (e.g.: using CHIP Tool from a mobile phone) and control of a light bulb over a low-power, 802.15.4 Thread network. It is capable of being paired into an existing Matter network along with other Matter-enabled devices.

The Matter device that runs the lighting application is controlled by the Matter controller device over the Thread protocol. By default, the Matter device has Thread disabled, and it should be paired over Bluetooth LE with the Matter controller and obtain configuration from it. The actions required before establishing full communication are described below.

Bluetooth LE Advertising

In this example, to commission the device onto a Matter network, it must be discoverable over Bluetooth LE. For security reasons, you must start Bluetooth LE advertising manually after powering up the device by pressing Button SW2.

Bluetooth LE Rendezvous

In this example, the commissioning procedure (called rendezvous) is done over Bluetooth LE between a Matter device and the Matter controller, where the controller has the commissioner role.

To start the rendezvous, the controller must get the commissioning information from the Matter device. The data payload is encoded within a QR code, or printed to the UART console.

Thread Provisioning

Device UI

The example application provides a simple UI that depicts the state of the device and offers basic user control. This UI is implemented via the general-purpose LEDs and buttons built in the K32W1 EVK board.

LED 2 shows the overall state of the device and its connectivity. Four states are depicted:

• Short Flash On (50ms on/950ms off) — The device is in an unprovisioned (unpaired) state and is waiting for a commissioning application to connect.

• Rapid Even Flashing (100ms on/100ms off) — The device is in an unprovisioned state and a commissioning application is connected via BLE.

• Short Flash Off (950ms on/50ms off) — The device is full provisioned, but does not yet have full network (Thread) or service connectivity.

• Solid On — The device is fully provisioned and has full network and service connectivity.

NOTE: LED2 will be disabled when CHIP_DEVICE_CONFIG_ENABLE_OTA_REQUESTOR is enabled. On K32W1 EVK board, PTB0 is wired to LED2 also is wired to CS (Chip Select) External Flash Memory. OTA image is stored in external memory because of it's size. If LED2 is enabled then it will affect External Memory CS and OTA will not work.

RGB LED shows the state of the simulated light bulb. When the LED is lit the light bulb is on; when not lit, the light bulb is off.

Button SW2 can be used to start BLE advertising. A SHORT press of the button will enable Bluetooth LE advertising for a predefined period of time. A LONG Press Button SW2 initiates a factory reset. After an initial period of 3 seconds, LED 2 and RGB LED will flash in unison to signal the pending reset. After 6 seconds will cause the device to reset its persistent configuration and initiate a reboot. The reset action can be cancelled by press SW2 button at any point before the 6 second limit.

Button SW3 can be used to change the state of the simulated light bulb. This can be used to mimic a user manually operating a switch. The button behaves as a toggle, swapping the state every time it is short pressed. When long pressed, it does a clean soft reset that takes into account Matter shutdown procedure.

Building

In order to build the Matter example, we recommend using a Linux distribution (the demo-application was compiled on Ubuntu 20.04).

• Download K32W1 SDK for Matter. Creating an nxp.com account is required before being able to download the SDK. Once the account is created, login and follow the steps for downloading K32W148-EVK MCUXpresso SDK. The SDK Builder UI selection should be similar with the one from the image below.

  

  Please refer to Matter release notes for getting the latest released SDK.

user@ubuntu:~/Desktop/git/connectedhomeip$ export NXP_K32W1_SDK_ROOT=/home/user/Desktop/SDK_K32W1/
user@ubuntu:~/Desktop/git/connectedhomeip$ source ./scripts/activate.sh
user@ubuntu:~/Desktop/git/connectedhomeip$ scripts/checkout_submodules.py --shallow --platform nxp --recursive
user@ubuntu:~/Desktop/git/connectedhomeip$ cd examples/lighting-app/nxp/k32w/k32w1
user@ubuntu:~/Desktop/git/connectedhomeip/examples/lighting-app/nxp/k32w/k32w1$ gn gen out/debug
user@ubuntu:~/Desktop/git/connectedhomeip/examples/lighting-app/nxp/k32w/k32w1$ ninja -C out/debug

In case that Openthread CLI is needed, chip_with_ot_cli build argument must be set to 1.

After a successful build, the elf and srec files are found in out/debug/ - see the files prefixed with chip-k32w1-light-example.

SMU2 Memory

Some Matter instances and global variables can be placed in the NBU SMU2 memory. When compiling with OpenThread FTD support (chip_openthread_ftd=true) and with use_smu2_static=true, the following components are placed in SMU2 memory:

• gImageProcessor from OTAImageProcessorImpl.cpp.
• gApplicationProcessor from OTAHooks.cpp.
• Server::sServer from Server.cpp.
• ThreadStackManagerImpl::sInstance from ThreadStackManagerImpl.cpp.

These instances and global variables are placed in SMU2 memory through name matching in the application linker script. They should not be changed or, if changed, the names must be updated in k32w1_app.ld. See k32w1_app.ld for names and SMU2 memory range size.

The OpenThread buffers can be allocated from a 13KB SMU2 range after a successful commissioning process until a factory reset is initiated. This way, the OpenThread buffers will be dynamically allocated instead of statically, freeing some SRAM. To enable this feature compile with OpenThread FTD support (chip_openthread_ftd=true) and with use_smu2_dynamic=true.

LED PWM

In the default configuration, the onboard RGB LED pins are configured as GPIO pins. In order to enable the dimming feature, the pins need to be configured in PWM mode and synced with channels of the TPM (Timer PWM Module). To enable this feature, compile the application with: chip_config_dimmable_led=true

If the feature is enabled, the LED brightness can be controlled using Level control cluster commands.

Manufacturing data

Use chip_with_factory_data=1 in the gn build command to enable factory data.

For a full guide on manufacturing flow, please see Guide for writing manufacturing data on NXP devices.

Flashing

Two images must be written to the board: one for the host (CM33) and one for the NBU (CM3).

The image needed on the host side is the one generated in out/debug/ while the one needed on the NBU side can be found in the downloaded NXP-SDK package at path - middleware\wireless\ieee-802.15.4\bin\k32w1\k32w1_nbu_ble_15_4_dyn_matter_$version.sb3.

Flashing the NBU image

NBU image should be written only when a new NXP-SDK is released.

K32W148 board quick start guide can be used for updating the NBU/radio core:

• Section 2.5 – Get Software – install SPSDK (Secure Provisioning Command Line Tool)
• Section 3.3 – Updating NBU for Wireless examples - use the corresponding .sb3 file found in the SDK package at path middleware\wireless\ieee-802.15.4\bin\k32w1\

Flashing the host image

Host image is the one found under out/debug/. It should be written after each build process.

If debugging is needed then jump directly to the Debugging section. Otherwise, if only flashing is needed then JLink 7.84b can be used:

• Plug K32W1 to the USB port (no need to keep the SW4 button pressed while doing this)

• Create a new file, commands_script, with the following content (change application name accordingly):

reset
halt
loadfile chip-k32w1-light-example.srec
reset
go
quit

• copy the application and commands_script in the same folder that JLink executable is placed. Execute:

$  jlink -device K32W1480 -if SWD -speed 4000 -autoconnect 1 -CommanderScript commands_script

Debugging

One option for debugging would be to use MCUXpresso IDE.

• Drag-and-drop the zip file containing the NXP SDK in the “Installed SDKs” tab:

• Import any demo application from the installed SDK:

Import SDK example(s).. -> choose a demo app (demo_apps -> hello_world) -> Finish

• Flash the previously imported demo application on the board:

Right click on the application (from Project Explorer) -> Debug as -> JLink/CMSIS-DAP

After this step, a debug configuration specific for the K32W1 board was created. This debug configuration will be used later on for debugging the application resulted after ot-nxp compilation.

• Import Matter repo in MCUXpresso IDE as Makefile Project. Use none as Toolchain for Indexer Settings:

File -> Import -> C/C++ -> Existing Code as Makefile Project

• Replace the path of the existing demo application with the path of the K32W1 application:

Run -> Debug Configurations... -> C/C++ Application

OTA

Convert srec into sb3 file

The OTA image files must be encrypted using Over The Air Programming Tool (OTAP). Bootloader will load the new OTA image only if it detects that the file was encrypted with the OTAP correct keys.

.srec file is input for Over The air Programming (OTAP) application (unencrypted) and it's converted to .sb3 format (encrypted).

In OTAP application

• select OTA protocol => OTAP Matter
• Browse File
• follow default options (KW45/K32W148, Preserve NVM)
• image information: will update “Application Core (MCU)” - this will generate the image only for the CM33 core
• keep other settings at default values

Convert sb3 into ota file

In order to build an OTA image, use NXP wrapper over the standard tool src/app/ota_image_tool.py:

• scripts/tools/nxp/factory_data_generator/ota_image_tool.py The tool can be used to generate an OTA image with the following format: | OTA image header | TLV1 | TLV2 | ... | TLVn | where each TLV is in the form |tag|length|value|

Note that “standard” TLV format is used. Matter TLV format is only used for factory data TLV value.

Please see more in the OTA image tool guide.

Here is an example that generates an OTA image with application update TLV from a sb3 file:

./scripts/tools/nxp/ota/ota_image_tool.py create -v 0xDEAD -p 0xBEEF -vn 43033 -vs "1.0" -da sha256 --app-input-file ~/binaries/chip-k32w1-43033.sb3 ~/binaries/chip-k32w1-43033.ota

A note regarding OTA image header version (-vn option). An application binary has its own software version (given by CHIP_DEVICE_CONFIG_DEVICE_SOFTWARE_VERSION, which can be overwritten). For having a correct OTA process, the OTA header version should be the same as the binary embedded software version. A user can set a custom software version in the gn build args by setting chip_software_version to the wanted version.

Running OTA

The OTA topology used for OTA testing is illustrated in the figure below. Topology is similar with the one used for Matter Test Events.

The concept for OTA is the next one:

• there is an OTA Provider Application that holds the OTA image. In our case, this is a Linux application running on an Ubuntu based-system;
• the OTA Requestor functionality is embedded inside the Lighting Application. It will be used for requesting OTA blocks from the OTA Provider;
• the controller (a linux application called chip-tool) will be used for commissioning both the device and the OTA Provider App. The device will be commissioned using the standard Matter flow (BLE + IEEE 802.15.4) while the OTA Provider Application will be commissioned using the onnetwork option of chip-tool;
• during commissioning, each device is assigned a node id by the chip-tool (can be specified manually by the user). Using the node id of the device and of the lighting application, chip-tool triggers the OTA transfer by invoking the announce-ota-provider command - basically, the OTA Requestor is informed of the node id of the OTA Provider Application.

Computer #1 can be any system running an Ubuntu distribution. We recommand using CSA official instructions from here, where RPi 4 are proposed. Also, CSA official instructions document point to the OS/Docker images that should be used on the RPis. For compatibility reasons, we recommand compiling chip-tool and OTA Provider applications with the same commit id that was used for compiling the Lighting Application. Also, please note that there is a single controller (chip-tool) running on Computer #1 which is used for commissioning both the device and the OTA Provider Application. If needed, these instructions could be used for connecting the RPis to WiFi.

Build the Linux OTA provider application:

user@computer1:~/connectedhomeip$ : ./scripts/examples/gn_build_example.sh examples/ota-provider-app/linux out/ota-provider-app chip_config_network_layer_ble=false

Build Linux chip-tool:

user@computer1:~/connectedhomeip$ : ./scripts/examples/gn_build_example.sh examples/chip-tool out/chip-tool-app

Start the OTA Provider Application:

user@computer1:~/connectedhomeip$ : rm -rf /tmp/chip_*
user@computer1:~/connectedhomeip$ : ./out/ota-provider-app/chip-ota-provider-app -f chip-k32w1-43033.ota

Provision the OTA provider application and assign node id 1. Also, grant ACL entries to allow OTA requestors:

user@computer1:~/connectedhomeip$ : rm -rf /tmp/chip_*
user@computer1:~/connectedhomeip$ : ./out/chip-tool-app/chip-tool pairing onnetwork 1 20202021
user@computer1:~/connectedhomeip$ : ./out/chip-tool-app/chip-tool accesscontrol write acl '[{"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [112233], "targets": null}, {"fabricIndex": 1, "privilege": 3, "authMode": 2, "subjects": null, "targets": null}]' 1 0

Provision the device and assign node id 2:

user@computer1:~/connectedhomeip$ : ./out/chip-tool-app/chip-tool pairing ble-thread 2 hex:<operationalDataset> 20202021 3840

Start the OTA process:

user@computer1:~/connectedhomeip$ : ./out/chip-tool-app/chip-tool otasoftwareupdaterequestor announce-ota-provider 1 0 0 0 2 0

Known issues

• SRP cache on the openthread border router needs to flushed each time a new commissioning process is attempted. For this, factory reset the device, then execute ot-ctl server disable followed by ot-ctl server enable. After this step, the commissioning process of the device can start;
• Due to some MDNS issues, the commissioning of the OTA Provider Application may fail. Please make sure that the SRP cache is disabled (ot-ctl srp server disable) on the openthread border router while commissioning the OTA Provider Application;
• No other Docker image should be running (e.g.: Docker image needed by Test Harness) except the OTBR one. A docker image can be killed using the command:

user@computer1:~/connectedhomeip$ : sudo docker kill $container_id

• In order to avoid MDNS issues, only one interface should be active at one time. E.g.: if WiFi is used then disable the Ethernet interface and also disable multicast on that interface:

user@computer1:~/connectedhomeip$ sudo ip link set dev eth0 down
user@computer1:~/connectedhomeip$ sudo ifconfig eth0 -multicast

• If OTBR Docker image is used, then the “-B” parameter should point to the interface used for the backbone.

• If Wi-Fi is used on a RPI4, then a 5Ghz network should be selected. Otherwise, issues related to BLE-WiFi combo may appear.

Running RPC console

To build example with RPC enabled, use the following gn command: gn gen out/debug --args='import("//with_pw_rpc.gni") treat_warnings_as_errors=false'

The application runs an RPC server and processes events coming from an RPC client. An example of an RPC client is the chip-console, which can be accessed by running: chip-console --device /dev/tty.<SERIALDEVICE> -b 115200 -o pw_log.out

The console should already have been installed in the virtual environment. From the chip-console, a user can send specific commands to the device, e.g.:

• To toggle the LED (#define LIGHT_BUTTON 2 in app_config.h) rpcs.chip.rpc.Button.Event(idx=2)
• To start BLE advertising (#define BLE_BUTTON 4 in app_config.h) rpcs.chip.rpc.Button.Event(idx=4)
• To reboot the device rpcs.chip.rpc.Device.Reboot()