tree: 65e9e110d50eefc96920b7ae2163d84a0339cf99 [path history] [tgz]
  1. boards/
  2. main/
  3. sysbuild/
  4. third_party/
  5. .gitignore
  6. CMakeLists.txt
  7. Kconfig
  8. Kconfig.sysbuild
  9. pm_static_nrf52840dk_nrf52840.yml
  10. pm_static_nrf52840dk_nrf52840_release.yml
  11. pm_static_nrf5340dk_nrf5340_cpuapp.yml
  12. pm_static_nrf5340dk_nrf5340_cpuapp_release.yml
  13. pm_static_nrf7002dk_nrf5340_cpuapp.yml
  14. pm_static_nrf7002dk_nrf5340_cpuapp_release.yml
  15. prj.conf
  16. prj_release.conf
  17. README.md
  18. sysbuild.conf
examples/light-switch-app/nrfconnect/README.md

Matter nRF Connect Light Switch Example Application

Note: This example is intended only to perform smoke tests of a Matter solution integrated with nRF Connect SDK platform. The example quality is not production ready and it may contain minor bugs or use not optimal configuration. It is not recommended to use this example as a basis for creating a market ready product.

For the production ready and optimized Matter samples, see nRF Connect SDK samples. The Matter samples in nRF Connect SDK use various additional software components and provide multiple optional features that improve the developer and user experience. To read more about it, see Matter support in nRF Connect SDK page. Using Matter samples from nRF Connect SDK allows you to get a full Nordic technical support via DevZone portal.

The nRF Connect Light Switch Example demonstrates how to remotely control a lighting devices such as light bulbs or LEDs. The application should be used together with the lighting app example. The light switch uses buttons to test changing the lighting application example LED state and works as a brightness dimmer. You can use this example as a reference for creating your own application.

The example is based on Matter and Nordic Semiconductor's nRF Connect SDK, and was created to facilitate testing and certification of a Matter device communicating over a low-power, 802.15.4 Thread network, or Wi-Fi network.

The example behaves as a Matter accessory, that is a device that can be paired into an existing Matter network and can be controlled by this network. In the case of Thread, this device works as a Thread Sleepy End Device. Support for both Thread and Wi-Fi is mutually exclusive and depends on the hardware platform, so only one protocol can be supported for a specific light switch device.

Overview

This example is running on the nRF Connect platform, which is based on Nordic Semiconductor‘s nRF Connect SDK and Zephyr RTOS. Visit Matter’s nRF Connect platform overview to read more about the platform structure and dependencies.

By default, the Matter accessory device has IPv6 networking disabled. You must pair it with the Matter controller over Bluetooth® LE to get the configuration from the controller to use the device within a Thread or Wi-Fi network. You have to make the device discoverable manually (for security reasons). See Bluetooth LE advertising to learn how to do this. The controller must get the commissioning information from the Matter accessory device and provision the device into the network.

You can test this application remotely over the Thread or the Wi-Fi protocol, which in either case requires more devices, including a Matter controller that you can configure either on a PC or a mobile device.

The sample uses buttons for controlling the bound device's LEDs. You can test it in the following ways:

  • Standalone, using a single DK that runs the light switch application.

  • Remotely over the Thread or the Wi-Fi protocol, which in either case requires more devices, including a Matter controller that you can configure either on a PC or a mobile device.

In Matter, the following types of light switch devices are available:

  • Group 1: On/Off Light Switch, Dimmer Switch, Color Dimmer Switch, Control Bridge
  • Group 2: Generic Switch

The first type (here referred to as Group 1) uses client application clusters (for example, Level Control) and bindings to send commands to the server clusters. This type of switch is on the endpoint 1 of this example.

With the second type (Group 2), controllers can use event subscriptions to be informed about changes on the switch server cluster. This type of switch is on the endpoint 2 of this example.

Group 1 light switch devices overview

A light switch device is a simple embedded controller, which has the ability to control lighting devices, such as light bulbs or LEDs. After commissioning into a Matter network, the light switch device does not know what it can control. In other words, it has no information about another device being connected to the same network. You must provide this information to the light switch through the process called binding, which links clusters and endpoints on both devices, so that the devices can interact with each other. This functionality is on the endpoint 1 and triggered by Button 2.

Generic Switch

The Generic Switch on the endpoint 2 offers the switch server cluster. It implements the Momentary Switch (MS) and Momentary Switch Release (MSR) features. For this reason, it sends event notifications InitialPress and ShortRelease if Button 3 of the DK is pressed and released.

Common example settings

The Matter device that runs the light switch application is controlled by the Matter controller device over the Thread protocol. By default, the Matter device has Thread disabled, and it should be paired with the Matter controller and get configuration from it. Some actions required before establishing full communication are described below.

The example can be configured to use the secure bootloader and utilize it for performing over-the-air Device Firmware Upgrade using Bluetooth LE.

Bluetooth LE advertising

In this example, to commission the device onto a Matter network, it must be discoverable over Bluetooth LE. For security reasons, you must start Bluetooth LE advertising manually after powering up the device by pressing:

  • On nRF52840 DK, nRF5340 DK, and nRF21540 DK: Button 4.

  • On nRF7002 DK: Button 2.

Bluetooth LE rendezvous

In this example, the commissioning procedure is done over Bluetooth LE between a Matter device and the Matter controller, where the controller has the commissioner role.

To start the rendezvous, the controller must get the commissioning information from the Matter device. The data payload is encoded within a QR code, printed to the UART console, and shared using an NFC tag. The emulation of the NFC tag emulation starts automatically when Bluetooth LE advertising is started and stays enabled until Bluetooth LE advertising timeout expires.

Thread or Wi-Fi provisioning

The provisioning operation, which is the Last part of the rendezvous procedure, involves sending the Thread or Wi-Fi network credentials from the Matter controller to the Matter device. As a result, the device joins the Thread or Wi-Fi network and can communicate with other devices in the network.

Device Firmware Upgrade

The example supports over-the-air (OTA) device firmware upgrade (DFU) using one of the two available methods:

  • Matter OTA DFU that is mandatory for Matter-compliant devices. This option is enabled by default.
  • Simple Management Protocol over Bluetooth LE from Nordic Semiconductor's nRF Connect SDK. This is an optional proprietary method that is not part of the Matter specification and can be enabled to work alongside the default Matter OTA DFU.

For both methods, the MCUboot bootloader solution is used to replace the old firmware image with the new one.

Matter Over-the-Air DFU

The Matter over-the-air DFU distinguishes two types of nodes: OTA Provider and OTA Requestor.

An OTA Provider is a node that hosts a new firmware image and is able to respond on an OTA Requestor's queries regarding availability of new firmware images or requests to start sending the update packages.

An OTA Requestor is a node that wants to download a new firmware image and sends requests to an OTA Provider to start the update process.

Simple Management Protocol

Simple Management Protocol (SMP) is a basic transfer encoding that is used for device management purposes, including application image management. SMP supports using different transports, such as Bluetooth LE, UDP, or serial USB/UART.

In this example, the Matter device runs the SMP Server to download the application update image using the Bluetooth LE transport.

See the Building with Device Firmware Upgrade support section to learn how to enable SMP and use it for the DFU purpose in this example.

Bootloader

MCUboot is a secure bootloader used for swapping firmware images of different versions and generating proper build output files that can be used in the device firmware upgrade process.

The bootloader solution requires an area of flash memory to swap application images during the firmware upgrade. Nordic Semiconductor devices use an external memory chip for this purpose. The memory chip communicates with the microcontroller through the QSPI bus.

See the Building with Device Firmware Upgrade support section to learn how to change MCUboot and flash configuration in this example.

Requirements

The application requires a specific revision of the nRF Connect SDK to work correctly. See Setting up the environment for more information.

Supported devices

The example supports building and running on the following devices:

Hardware platformBuild targetPlatform image
nRF52840 DKnrf52840dk/nrf52840nRF52840 DK
nRF5340 DKnrf5340dk/nrf5340/cpuappnRF5340 DK
nRF7002 DKnrf7002dk/nrf5340/cpuappnRF7002 DK

IPv6 network support

The development kits for this sample offer the following IPv6 network support for Matter:

  • Matter over Thread is supported for nrf52840dk/nrf52840 and nrf5340dk/nrf5340/cpuapp.
  • Matter over Wi-Fi is supported for nrf7002dk/nrf5340/cpuapp.

Additional requirements for testing

If you want to test the Light Switch Example application with other devices, you also need to flash and program the following examples using the compatible development kits:

Read the CHIP Tool user guide to learn how to commission the lighting device to the same Matter network using the CHIP Tool.

Device UI

This section lists the User Interface elements that you can use to control and monitor the state of the device. These correspond to PCB components on the platform image.

LEDs

This section describes all behaviors of LEDs located on platform image.

LED 1 shows the overall state of the device and its connectivity. The following states are possible:

  • Short Flash On (50 ms on/950 ms off) — The device is in the unprovisioned (unpaired) state and is waiting for a commissioning application to connect.

  • Rapid Even Flashing (100 ms on/100 ms off) — The device is in the unprovisioned state and a commissioning application is connected through Bluetooth LE.

  • Short Flash Off (950ms on/50ms off) — The device is fully provisioned, but does not yet have full connectivity for Thread or Wi-Fi network.

  • Solid On — The device is fully provisioned.

LED 2 simulates the BLE DFU process. The following states are possible:

  • Off — BLE is not advertising and DFU can not be performed.

  • Rapid Even Flashing (30 ms off / 170 ms on) — BLE is advertising, DFU process can be started.

All LEDs

Blink in unison when the factory reset procedure is initiated.

Buttons

This section describes a reaction to pressing or holding buttons located on the platform image.

Button 1 can be used for the following purposes:

  • Pressed for less than 3 s — Initiates the OTA software update process. This feature is disabled by default, but can be enabled by following the Building with Device Firmware Upgrade support instructions.

  • Pressed for more than 3 s — initiates the factory reset of the device. Releasing the button within the 3-second window cancels the factory reset procedure.

Button 2 can be used for the following purposes:

  • On nRF52840 DK, nRF5340 DK and nRF21540 DK:

    • If pressed for less than 0.5 seconds, it changes the light state to the opposite one on the bound lighting device lighting-app

    • If pressed for more than 0.5 seconds, it changes the brightness of the light on the bound lighting bulb device lighting-app. The brightness is changing from 0% to 100% with 1% increments every 300 milliseconds as long as Button 2 is pressed.

  • On nRF7002 DK:

    • If the device is not commissioned to a Matter network, it starts the NFC tag emulation, enables Bluetooth LE advertising for the predefined period of time (15 minutes by default), and makes the device discoverable over Bluetooth LE. This button is used during the commissioning procedure.

    • If the device is commissioned to a Matter network, it controls the light on the bound lighting device. Depending on how long you press the button:

      - If pressed for less than 0.5 seconds, it changes the light state to the opposite one on the bound lighting device ([lighting-app](../../lighting-app/nrfconnect/)).
      
      - If pressed for more than 0.5 seconds, it changes the brightness of the light on the bound lighting bulb device ([lighting-app](../../lighting-app/nrfconnect/)). The brightness is changing from 0% to 100% with 1% increments every 300 milliseconds as long as **Button 2** is pressed.
      

Button 4

  • On nRF52840 DK, nRF5340 DK and nRF21540 DK:

    Starts the NFC tag emulation, enables Bluetooth LE advertising for the predefined period of time (15 minutes by default), and makes the device discoverable over Bluetooth LE. This button is used during the commissioning procedure.

  • On nRF7002 DK:

    Not available.

SEGGER J-Link USB port can be used to get logs from the device or communicate with it using the command line interface.

NFC port with antenna attached can be used to start the rendezvous by providing the commissioning information from the Matter device in a data payload that can be shared using NFC.

Matter CLI commands

The Matter CLI allows to run commands via serial interface after USB cable connection to Nordic Semiconductor's kit.

To enable the Matter CLI, you must compile the Light Switch Example application with the additional option -DCONFIG_CHIP_LIB_SHELL=y. Run the following command with build-target replaced with the build target name of Nordic Semiconductor's kit you are using (for example, nrf52840dk/nrf52840):

west build -b build-target --sysbuild -- -DCONFIG_CHIP_LIB_SHELL=y

You can use the following commands to control a device that is programmed with the Light Switch Example application by using the Matter CLI:

uart:~$ switch onoff on     : sends unicast On command to bound device
uart:~$ switch onoff off    : sends unicast Off command to bound device
uart:~$ switch onoff toggle : sends unicast Toggle command to bound device

You can use the following commands a group of devices that are programmed with the Light Switch Example application by using the Matter CLI:

uart:~$ switch groups onoff on     : sends multicast On command to all bound devices in a group
uart:~$ switch groups onoff off    : sends multicast Off command to  all bound devices in a group
uart:~$ switch groups onoff toggle : sends multicast Toggle command to all bound devices in a group

Check the CLI user guide to learn how to use other CLI commands of the application.

Setting up the environment

Before building the example, check out the Matter repository and sync submodules using the following command:

    $ python3 scripts/checkout_submodules.py --shallow --platform nrfconnect

Note:

For Linux operating system install SEGGER J-Link Software.

Install Command Line Tools

With admin permissions enabled, download and install the nRF Command Line Tools.

Install Toolchain Manager

Toolchain Manager is available from nRF Connect for Desktop, a cross-platform tool that provides different applications that simplify installing the nRF Connect SDK. Both the tool and the application are available for Windows, Linux, and macOS.

To install the Toolchain Manager app, complete the following steps:

  1. Download nRF Connect for Desktop for your operating system.

  2. Install and run the tool on your machine.

  3. In the APPS section, click Install button on the Toolchain Manager tab.

Install nRF Connect SDK

Complete the following steps to install the nRF Connect SDK:

  1. Open Toolchain Manager in nRF Connect for Desktop.

  2. Click the Install button next to the recommended version of the nRF Connect SDK.

  3. A pop-up window will inform you about the current installation directory. If you want to change the directory, click the Change directory button. Otherwise, click the Continue installation button.

  4. When the nRF Connect SDK is installed on your machine, the Install button changes to the Open VS Code button.

  5. Click the dropdown menu next to the Open VS Code button for the installed nRF Connect SDK version, and select Open terminal.

  6. Make sure that the nRF Connect SDK version is compatible with the Matter SDK version:

         $ cd {connectedhomeip directory}
         $ python3 scripts/setup/nrfconnect/update_ncs.py --update
    

Now you can proceed with the Building instruction.

Building

Complete the following steps to build the sample:

  1. Navigate to the example's directory:

    $ cd examples/light-switch-app/nrfconnect
    
  2. Run the following command to build the example, with build-target replaced with the build target name of the Nordic Semiconductor's kit you own, for example nrf52840dk/nrf52840:

     $ west build -b build-target --sysbuild
    

    You only need to specify the build target on the first build. See Requirements for the build target names of compatible kits.

The output zephyr.hex file will be available in the build/nrfconnect/zephyr/ directory.

Removing build artifacts

If you're planning to build the example for a different kit or make changes to the configuration, remove all build artifacts before building. To do so, use the following command:

$ rm -r build

Building with release configuration

To build the example with release configuration that disables the diagnostic features like logs and command-line interface, run the following command:

$ west build -b build-target --sysbuild -- -DFILE_SUFFIX=release

Remember to replace build-target with the build target name of the Nordic Semiconductor's kit you own.

Building with Device Firmware Upgrade support

Support for DFU using Matter OTA is enabled by default.

To enable DFU over Bluetooth LE, run the following command with build-target replaced with the build target name of the Nordic Semiconductor kit you are using (for example nrf52840dk/nrf52840):

$ west build -b build-target --sysbuild -- -DCONFIG_CHIP_DFU_OVER_BT_SMP=y

Note:

There are two types of Device Firmware Upgrade modes: single-image DFU and multi-image DFU. Single-image mode supports upgrading only one firmware image, the application image, and should be used for single-core nRF52840 DK devices. Multi-image mode allows to upgrade more firmware images and is suitable for upgrading the application core and network core firmware in two-core nRF5340 DK devices.

Changing bootloader configuration

To change the default MCUboot configuration, edit the prj.conf file located in the sysbuild/mcuboot directory.

Make sure to keep the configuration consistent with changes made to the application configuration. This is necessary for the configuration to work, as the bootloader image is a separate application from the user application and it has its own configuration file.

Changing flash memory settings

In the default configuration, the MCUboot uses the Partition Manager to configure flash partitions used for the bootloader application image slot purposes. You can change these settings by defining static partitions. This example uses this option to define using an external flash.

To modify the flash settings of your board (that is, your build-target, for example nrf52840dk/nrf52840), edit the pm_static_<build_target>.yml file (for example pm_static_nrf52840dk_nrf52840.yml), located in the main application directory.

Configuring the example

The Zephyr ecosystem is based on Kconfig files and the settings can be modified using the menuconfig utility.

To open the menuconfig utility, run the following command from the example directory:

$ west build -b build-target --sysbuild -t menuconfig

Remember to replace build-target with the build target name of the Nordic Semiconductor's kit you own.

Changes done with menuconfig will be lost if the build directory is deleted. To make them persistent, save the configuration options in the prj.conf file.

Example build types

The example uses different configuration files depending on the supported features. Configuration files are provided for different build types and they are located in the application root directory.

The prj.conf file represents a debug build type. Other build types are covered by dedicated files with the build type added as a suffix to the prj part, as per the following list. For example, the release build type file name is prj_release.conf. If a board has other configuration files, for example associated with partition layout or child image configuration, these follow the same pattern.

Before you start testing the application, you can select one of the build types supported by the sample. This sample supports the following build types, depending on the selected board:

  • debug -- Debug version of the application - can be used to enable additional features for verifying the application behavior, such as logs or command-line shell.
  • release -- Release version of the application - can be used to enable only the necessary application functionalities to optimize its performance.

For more information, see the Configuring nRF Connect SDK examples page.

Flashing and debugging

To flash the application to the device, use the west tool and run the following command from the example directory:

$ west flash --erase

If you have multiple development kits connected, west will prompt you to pick the correct one.

To debug the application on target, run the following command from the example directory:

$ west debug

Testing the example

After building and flashing the example, you can test its functionalities. For this purpose, you need to prepare a second device that is programmed with the Lighting Example, perform the binding process, and add Access Control Lists (ACLs).

Commissioning the lighting device

To commission the Lighting Example Application to the same Matter network, read the CHIP Tool user guide.

Binding cluster and endpoints

Binding links clusters and endpoints on both devices, which enables them to communicate with each other.

To perform binding, you need a controller that can write the binding table to the light switch device and write proper ACL to the endpoint light bulb on the Lighting Example application. For example, you can use the CHIP Tool for Windows or Linux as the controller. The ACL should contain information about all clusters that can be called by the light switch application. See the section about interacting with ZCL clusters in the CHIP Tool's user guide for more information about ACLs.

You can perform the binding process to a single remote endpoint (unicast binding) or to a group of remote endpoints (group multicast).

Note: To use a light switch without brightness dimmer, apply only the first binding command with cluster no. 6.

Unicast binding to a remote endpoint using the CHIP Tool for Windows or Linux

In this scenario, commands are provided for a light switch device with the nodeId = 2 and a light bulb device with nodeId = 1, both commissioned to the same Matter network.

To perform the unicast binding process, complete the following steps:

  1. Build the CHIP Tool according to the steps from the CHIP Tool user guide.

  2. Go to the CHIP Tool build directory.

  3. Add an ACL to the development kit that is programmed with the Lighting Application Example by running the following command:

    chip-tool accesscontrol write acl '[{"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [112233], "targets": null}, {"fabricIndex": 1, "privilege": 3, "authMode": 2, "subjects": [2], "targets": [{"cluster": 6, "endpoint": 1, "deviceType": null}, {"cluster": 8, "endpoint": 1, "deviceType": null}]}]' 1 0
    

    In this command:

    • {"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [112233], "targets": null} is an ACL for the communication with the CHIP Tool.
    • {"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [2], "targets": [{"cluster": 6, "endpoint": 1, "deviceType": null}, {"cluster": 8, "endpoint": 1, "deviceType": null}]} is an ACL for binding (cluster no. 6 is the On/Off cluster and the cluster no. 8 is the Level Control cluster).

    This command adds permissions on the lighting application device that allows it to receive commands from the light switch device.

  4. Add a binding table to the Light Switch binding cluster:

    chip-tool binding write binding '[{"fabricIndex": 1, "node": 1, "endpoint": 1, "cluster": 6}, {"fabricIndex": 1, "node": 1, "endpoint": 1, "cluster": 8}]' 2 1
    

    In this command:

    • {"fabricIndex": 1, "node": <1>, "endpoint": 1, "cluster": 6} is a binding for the On/Off cluster.
    • {"fabricIndex": 1, "node": <1>, "endpoint": 1, "cluster": 8} is a binding for the Level Control cluster.

Note: When a light switch device reboots, the binding table is restored from flash memory and the device tries to bind a known device that is programmed with the Lighting Application Example.

Group multicast binding to the group of remote endpoints using the CHIP Tool for Windows or Linux

The group multicast binding lets you control more than one lighting device at a time using a single light switch.

The group multicast binding targets all development kits that are programmed with the Lighting Application Example and added to the same multicast group. After the binding is established, the light switch device can send multicast requests, and all of the devices in the bound groups can run the received command.

In this scenario, commands are provided for a light switch device with the nodeId = 2 and a light bulb device with nodeId = 1, both commissioned to the same Matter network.

To perform the unicast binding process, complete the following steps:

  1. Build the CHIP Tool according to the steps from the CHIP Tool user guide.

  2. Go to the CHIP Tool build directory.

  3. Add the light switch device to the multicast group by running the following command:

    chip-tool tests TestGroupDemoConfig --nodeId 1
    
  4. Add all light bulbs to the same multicast group by applying command below for each of the light bulbs, using the appropriate <node_id> (the user-defined ID of the node being commissioned except 2 due to use this <node_id> for light-switch) for each of them:

    chip-tool tests TestGroupDemoConfig --nodeId <node_id>
    
  5. Add Binding commands for group multicast:

    chip-tool binding write binding '[{"fabricIndex": 1, "group": 257}]' 2 1
    

Testing the communication

To test the communication between the light switch device and the bound devices, use light switch buttons or Matter CLI commands, as described in the Device UI section.

Testing the Generic Switch

To test the Generic Switch, complete the following steps:

  1. Enter the interactive mode of the CHIP Tool:

    chip-tool interactive start
    
  2. Subscribe to the InitialPress and ShortRelease event notifications:

switch subscribe-event initial-press 1 20 <node_id> 2 --is-urgent true
switch subscribe-event short-release 1 20 <node_id> 2 --is-urgent true --keepSubscriptions true
  1. Press Button 3 to test the new configuration. When pressing and releasing Button 3, both events should be sent to the controller.

Testing Device Firmware Upgrade

Read the DFU tutorial to see how to upgrade your device firmware.