Matter K32W1 Door Lock Example Application

For generic information related to door lock application, please see the common README.

• Matter K32W1 Door Lock Example Application
  • Introduction
  • Device UI
  • Building
  • Flashing
    • Flashing the NBU image
    • Flashing the host image
  • Debugging
  • OTA

Introduction

The following board was used when testing this Matter reference app for a k32w1 device:

Device UI

The state feedback is provided through LED effects:

NOTE: LED2 will be disabled when OTA is used. On K32W1 EVK board, PTB0 is wired to both LED2 and CS (Chip Select) of the External Flash Memory. Since the OTA image is stored in external memory, LED2 operations will affect OTA operation by corrupting packages and OTA will not work.

The user actions are summarized below:

Building

Manually building requires running the following commands:

user@ubuntu:~/Desktop/git/connectedhomeip$ cd examples/lock-app/nxp/k32w1
user@ubuntu:~/Desktop/git/connectedhomeip/examples/lock-app/nxp/k32w1$ gn gen out/debug
user@ubuntu:~/Desktop/git/connectedhomeip/examples/lock-app/nxp/k32w1$ ninja -C out/debug

Please note that running gn gen out/debug without --args option will use the default gn args values found in args.gni.

After a successful build, the elf and srec files are found in out/debug/. See the files prefixed with chip-k32w1-lock-example.

Flashing

Two images must be written to the board: one for the host (CM33) and one for the NBU (CM3).

The image needed on the host side is the one generated in out/debug/ while the one needed on the NBU side can be found in the downloaded NXP-SDK package at path - middleware\wireless\ieee-802.15.4\bin\k32w1\k32w1_nbu_ble_15_4_dyn_matter.sb3.

Flashing the NBU image

NBU image should be written only when a new NXP-SDK is released.

K32W148 board quick start guide can be used for updating the NBU/radio core:

• Section 2.5 – Get Software – install SPSDK (Secure Provisioning Command Line Tool)
• Section 3.3 – Updating NBU for Wireless examples - use the corresponding .sb3 file found in the SDK package at path middleware\wireless\ieee-802.15.4\bin\k32w1\

Flashing the host image

Host image is the one found under out/debug/. It should be written after each build process.

If debugging is needed then jump directly to the Debugging section. Otherwise, if only flashing is needed then JLink 7.84b or greater can be used:

• Plug K32W1 to the USB port (no need to keep the SW4 button pressed while doing this, e.g. ISP mode is not needed for host flashing)

• Connect JLink to the device:

  JLinkExe -device K32W1480 -if SWD -speed 4000 -autoconnect 1
  

• Run the following commands:

  reset
  halt
  loadfile chip-k32w1-lock-example.srec
  reset
  go
  quit
  

Debugging

One option for debugging would be to use MCUXpresso IDE.

• Drag-and-drop the zip file containing the NXP SDK in the “Installed SDKs” tab:

• Import any demo application from the installed SDK:

Import SDK example(s).. -> choose a demo app (demo_apps -> hello_world) -> Finish

• Flash the previously imported demo application on the board:

Right click on the application (from Project Explorer) -> Debug as -> JLink/CMSIS-DAP

After this step, a debug configuration specific for the K32W1 board was created. This debug configuration will be used later on for debugging the application resulted after ot-nxp compilation.

• Import Matter repo in MCUXpresso IDE as Makefile Project. Use none as Toolchain for Indexer Settings:

File -> Import -> C/C++ -> Existing Code as Makefile Project

• Replace the path of the existing demo application with the path of the K32W1 application:

Run -> Debug Configurations... -> C/C++ Application

OTA

Please see k32w1 OTA guide.