The nRF Connect example applications all come with a default configuration for building.
Check the information on this page if you want to modify the application configuration or add new functionalities to build your own application based on the provided example. This page also contains information about the configuration structure, which can be useful to better understand the building process.
Changing the default application configuration can be done either temporarily or permanently.
Regardless of the option, you will need to rebuild your application. This will require you to provide the build target name of the kit you are using. You can find the build target names in the Requirements section of the example you are building or on the Board support page in the nRF Connect SDK documentation.
You can change the configuration temporarily by editing the .config file in the build/zephyr/ directory, which stores all configuration options for the application generated as a result of the build process.
As long as you do not remove the current build directory or delete this file, your changes will be kept. However, if you do a clean build, your changes are gone, so it is not possible to save changes permanently this way.
Complete the following steps:
Build the application by typing the following command in the example directory, with build-target replaced with the build target name of the kit, for example nrf52840dk_nrf52840:
west build -b build-target
Run the terminal-based interface called menuconfig by typing the following command:
west build -t menuconfig
The menuconfig terminal window appears, in which you can navigate using arrow keys and other keys, based on the description at the bottom of the window.
Make the desired changes by following the menuconfig terminal instructions.
Press Q to save and quit.
Rebuild the application.
At this point, the configuration changes are applied to the output file and it can be flashed to the device.
The permanent solution is based on modifying the Kconfig configuration files, which are used as components of the building process. This makes the changes persistent across builds.
The best practice to make permanent changes is to edit the main application configuration file prj.conf, which is located in the example directory. This will result in overriding the existing configuration values.
This method is valid for the majority of cases. If you are interested in understanding the big picture of the configuration process, read the Configuration structure overview section below.
You can assigning a value to a configuration option by typing its full name preceded by the CONFIG_ prefix, and adding the = mark and the value.
Configuration options have different types and it is only possible to assign them values of proper type. Few examples:
CONFIG_SAMPLE_BOOLEAN_OPTION=yCONFIG_SAMPLE_INTEGER_OPTION=1234CONFIG_SAMPLE_STRING_OPTION="some_text"For more detailed information, read about setting Kconfig values in the nRF Connect SDK documentation.
Because Kconfig configuration files are used in the building process, make sure that you rebuild your application after editing them by typing the following command in the example directory, with build-target replaced with the build target name of the kit, for example nrf52840dk_nrf52840:
west build -b build-target
Zephyr RTOS and related software components, like drivers and libraries, provide a set of Kconfig files which define available configuration options and assign them default values for any application.
The application configuration is specified using Kconfig configuration files (*.conf), where available Kconfig options can be used and their default values overridden. Typically, there are many files having impact on the final configuration shape.
There is no need to modify all these files separately. See the following list for types of files you can find in the project and which of them are important from your perspective:
Build target configuration files. These are hardware-platform-dependent configuration files, which are automatically included based on the compilation build target name. They contain configuration for the kit and its peripherals.
Project configuration file. Every example application has its main configuration file called prj.conf that is located in the example directory. This file contains application-specific configuration or the most frequently changed options. Almost every configuration can be overridden in this file and probably this file is the most important one.
Overlays. Overlays are optional files usually used to extract configuration for some specific case or feature from the general application configuration. The main difference between them and the application prj.conf file is that they are not included automatically, so you can decide whether to build sample with or without them. Overlay files can be added to build by typing the following command in the example directory, with build-target replaced with the build target name (e.g. nrf52840dk_nrf52840) and overlay_file_name replaced with the overlay configuration file name (e.g. overlay-usb_support.conf):
$ west build -b build-target -- -DOVERLAY_CONFIG=overlay_file_name
Read the Kconfig guide in the nRF Connect SDK's Zephyr documentation if you are interested in getting more advanced and detailed information about the configuration structure.
When configuring Matter support using the nRF Connect platform, some configuration options are required, while other are optional and depend on what application behavior you want to achieve.
To use the Matter protocol, complete the following steps:
CONFIG_CHIP Kconfig option. Setting this option enables the Matter protocol stack and other associated Kconfig options, including CONFIG_CHIP_ENABLE_DNSSD_SRP that is required for the Matter device to be discoverable using DNS-SD.CONFIG_CHIP_PROJECT_CONFIG Kconfig option and define the path to the configuration file that specifies Vendor ID, Product ID, and other project-specific Matter settings.After enabling the Matter protocol and defining the path to the Matter configuration file, you can enable additional options in Kconfig.
You can enable the support for Thread Sleepy End Device in Matter by setting the following Kconfig options:
CONFIG_OPENTHREAD_MTDCONFIG_CHIP_ENABLE_SLEEPY_END_DEVICE_SUPPORTThe following Kconfig options can be used to tune Thread Sleepy End Device wake intervals:
CONFIG_CHIP_SED_IDLE_INTERVALCONFIG_CHIP_SED_ACTIVE_INTERVALYou can configure the Matter protocol to use an NFC tag for commissioning, instead of using a QR code, which is the default configuration.
To enable NFC for commissioning and share the onboarding payload in an NFC tag, set the CONFIG_CHIP_NFC_COMMISSIONING option.
By default, the factory reset procedure implemented in the Matter stack removes Matter-related settings only. If your application does not depend on any device-lifelong data stored in the non-volatile storage, set the CONFIG_CHIP_FACTORY_RESET_ERASE_NVS option to fully erase the NVS partition at the factory reset. This approach is more robust and regains the original NVS performance in case it has been polluted with unwanted entries.
You can enable logging for both the stack and Zephyr’s Logging API by setting the CONFIG_LOG option.
Zephyr allows you to configure log levels of different software modules independently. To change the log level configuration for the Matter module, set one of the available options:
CONFIG_MATTER_LOG_LEVEL_ERRCONFIG_MATTER_LOG_LEVEL_INFOCONFIG_MATTER_LOG_LEVEL_DBGYou can enable the Matter shell library using the CONFIG_CHIP_LIB_SHELL Kconfig option. This option lets you use the Matter specific shell commands. See Using CLI in nRF Connect examples for the list of available Matter shell commands.
Matter has many mandatory and optional ways to identify a specific device. These can be used for various purposes, such as dividing devices into groups (by function, by vendor, or by location), device commissioning or vendor-specific cases before the device was commissioned (for example, identifying factory software version or related features).
Only some part of these features can be configured using Kconfig options:
CONFIG_CHIP_DEVICE_TYPE - This option specifies the type of device that uses the Matter Device Type Identifier, for example Door Lock (0x000A) or Dimmable Light Bulb (0x0101).CONFIG_CHIP_COMMISSIONABLE_DEVICE_TYPE - This option enables including optional device type subtype in the commissionable node discovery record, which allows filtering of the discovery results to find the nodes that match the device type.CONFIG_CHIP_ROTATING_DEVICE_ID - This option enables the rotating device identifier, an optional feature that provides an additional unique identifier for each device. This identifier is similar to the serial number, but it additionally changes at predefined times to protect against long-term tracking of the device.