| # |
| # Copyright (c) 2022 Project CHIP Authors |
| # All rights reserved. |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| # Description: |
| # Configuration options CHIP ESP32 demo application. |
| # |
| |
| menu "Demo" |
| |
| choice |
| prompt "Device Type" |
| default DEVICE_TYPE_ESP32_DEVKITC if IDF_TARGET_ESP32 |
| default DEVICE_TYPE_ESP32_C3_DEVKITM if IDF_TARGET_ESP32C3 |
| default DEVICE_TYPE_ESP32_C2_DEVKITM if IDF_TARGET_ESP32C2 |
| default DEVICE_TYPE_ESP32_C6_DEVKITC if IDF_TARGET_ESP32C6 |
| help |
| Specifies the type of ESP32 device. |
| |
| Note that the "ESP32-DevKitC" choice is compatible with a number of clone devices |
| available from third-party manufacturers. |
| |
| config DEVICE_TYPE_ESP32_DEVKITC |
| bool "ESP32-DevKitC" |
| depends on IDF_TARGET_ESP32 |
| config DEVICE_TYPE_ESP32_WROVER_KIT |
| bool "ESP32-WROVER-KIT_V4.1" |
| depends on IDF_TARGET_ESP32 |
| config DEVICE_TYPE_M5STACK |
| bool "M5Stack" |
| depends on IDF_TARGET_ESP32 |
| config DEVICE_TYPE_ESP32_C3_DEVKITM |
| bool "ESP32C3-DevKitM" |
| depends on IDF_TARGET_ESP32C3 |
| config DEVICE_TYPE_ESP32_ETHERNET_KIT |
| bool "ESP32-Ethernet-Kit_A_V1.0" |
| select ENABLE_ETHERNET_TELEMETRY |
| depends on IDF_TARGET_ESP32 |
| config DEVICE_TYPE_ESP32_C2_DEVKITM |
| bool "ESP32C2-DevKitM" |
| depends on IDF_TARGET_ESP32C2 |
| config DEVICE_TYPE_ESP32_C6_DEVKITC |
| bool "ESP32C6-DevKitC" |
| depends on IDF_TARGET_ESP32C6 |
| config DEVICE_TYPE_ESP32_H2_DEVKITM |
| bool "ESP32H2-DevKitM" |
| depends on IDF_TARGET_ESP32H2 |
| endchoice |
| |
| config CHIP_PROJECT_CONFIG |
| string "CHIP Project Configuration file" |
| default "main/include/CHIPProjectConfig.h" |
| |
| choice |
| prompt "Rendezvous Mode" |
| default RENDEZVOUS_MODE_BLE if BT_ENABLED |
| default RENDEZVOUS_MODE_SOFTAP |
| help |
| Specifies the Rendezvous mode of the peripheral. |
| |
| config RENDEZVOUS_MODE_SOFTAP |
| bool "Soft-AP" |
| select ESP_WIFI_SOFTAP_SUPPORT |
| config RENDEZVOUS_MODE_BLE |
| bool "BLE" |
| depends on BT_ENABLED |
| config RENDEZVOUS_MODE_ON_NETWORK |
| bool "On-Network" |
| config RENDEZVOUS_MODE_SOFTAP_ON_NETWORK |
| bool "Soft-AP / On-Network" |
| select ESP_WIFI_SOFTAP_SUPPORT |
| config RENDEZVOUS_MODE_BLE_ON_NETWORK |
| bool "BLE / On-Network" |
| endchoice |
| |
| # NOTE: This config is not displayed as a input in the Kconfig menu, as its value is |
| # entirely derived from the Device Type choice. However the CONFIG_EXAMPLE_DISPLAY_TYPE |
| # define that is produced is needed to configure the TFT library correctly. |
| config TFT_PREDEFINED_DISPLAY_TYPE |
| int |
| range 0 5 |
| default 0 if DEVICE_TYPE_ESP32_DEVKITC || DEVICE_TYPE_ESP32_H2_DEVKITM |
| default 0 if DEVICE_TYPE_ESP32_C3_DEVKITM || DEVICE_TYPE_ESP32_C2_DEVKITM || DEVICE_TYPE_ESP32_C6_DEVKITC |
| default 3 if DEVICE_TYPE_M5STACK |
| default 4 if DEVICE_TYPE_ESP32_WROVER_KIT |
| |
| config HAVE_DISPLAY |
| bool |
| default y if DEVICE_TYPE_M5STACK || DEVICE_TYPE_ESP32_WROVER_KIT |
| default n if !(DEVICE_TYPE_M5STACK || DEVICE_TYPE_ESP32_WROVER_KIT) |
| |
| config RENDEZVOUS_MODE |
| int |
| range 0 8 |
| default 1 if RENDEZVOUS_MODE_SOFTAP |
| default 2 if RENDEZVOUS_MODE_BLE |
| default 4 if RENDEZVOUS_MODE_ON_NETWORK |
| default 5 if RENDEZVOUS_MODE_SOFTAP_ON_NETWORK |
| default 6 if RENDEZVOUS_MODE_BLE_ON_NETWORK |
| |
| config DISPLAY_AUTO_OFF |
| bool "Automatically turn off the M5Stack's Display after a few seconds" |
| default "y" |
| depends on DEVICE_TYPE_M5STACK |
| help |
| To reduce wear and heat the M5Stack's Display is automatically switched off after a few seconds |
| |
| config STATUS_LED_GPIO_NUM |
| int |
| range 0 40 |
| default 2 if DEVICE_TYPE_ESP32_DEVKITC #Use LED1 (blue LED) as status LED on DevKitC |
| default 2 if DEVICE_TYPE_ESP32_ETHERNET_KIT |
| default 8 if DEVICE_TYPE_ESP32_C3_DEVKITM || DEVICE_TYPE_ESP32_C2_DEVKITM || DEVICE_TYPE_ESP32_C6_DEVKITC || DEVICE_TYPE_ESP32_H2_DEVKITM |
| default 26 if DEVICE_TYPE_ESP32_WROVER_KIT |
| default 40 if DEVICE_TYPE_M5STACK |
| help |
| Each board has a status led, define its pin number. |
| |
| endmenu |
| |
| menu "PW RPC Debug channel" |
| depends on ENABLE_PW_RPC |
| config EXAMPLE_UART_PORT_NUM |
| int "UART port number" |
| range 0 2 if IDF_TARGET_ESP32 |
| range 0 1 if IDF_TARGET_ESP32C3 |
| default 0 |
| help |
| UART communication port number for the example. |
| See UART documentation for available port numbers. |
| |
| config EXAMPLE_UART_BAUD_RATE |
| int "UART communication speed" |
| range 1200 115200 |
| default 115200 |
| help |
| UART communication speed for Modbus example. |
| |
| config EXAMPLE_UART_RXD |
| int "UART RXD pin number" |
| range 0 34 if IDF_TARGET_ESP32 |
| range 0 19 if IDF_TARGET_ESP32C3 |
| default 5 |
| help |
| GPIO number for UART RX pin. See UART documentation for more information |
| about available pin numbers for UART. |
| |
| config EXAMPLE_UART_TXD |
| int "UART TXD pin number" |
| range 0 34 if IDF_TARGET_ESP32 |
| range 0 19 if IDF_TARGET_ESP32C3 |
| default 4 |
| help |
| GPIO number for UART TX pin. See UART documentation for more information |
| about available pin numbers for UART. |
| |
| endmenu |
