/dts-v1/;
/include/ "bl602_base.dtsi";
// version: 17
// last_comp_version: 16
// boot_cpuid_phys: 0x0

/ {
    model = "bl bl602 IOT board";
    compatible = "bl,bl602-sample", "bl,bl602-common";
    #address-cells = <0x1>;
    #size-cells = <0x1>;
    gpio {
        #address-cells = <1>;
        #size-cells = <1>;
        max_num = <40>;
        gpio0 {                                  
            status = "okay";                     
            pin  = <5>;                          
            feature = "led";                     
            active = "Hi"; //Hi or Lo
            mode = "blink"; //blink or hearbeat
            time = <100>; //duration for this mode
        };
        gpio1 {                                  
            status = "disable";                     
            pin  = <6>;                          
            feature = "led";                     
            active = "Hi"; //Hi or Lo
            mode = "blink"; //blink or hearbeat
            time = <100>; //duration for this mode
        };
        gpio2 {
            status = "okay";
            pin = <2>;
            feature = "button";
            active = "Hi";
            mode = "multipress";
            button {
                debounce = <10>;
                short_press_ms {
                    start = <100>;
                    end = <3000>;
                    kevent = <2>;
                };
                long_press_ms {
                    start = <6000>;
                    end = <10000>;
                    kevent = <3>;
                };
                longlong_press_ms {
                    start = <15000>;
                    kevent = <4>;
                };
                trig_level = "Hi";
            };
            hbn_use = "disable";
        };
    };
    i2s {
        #address-cells = <1>;
        #size-cells = <1>;
        i2s@40017000 {
            status = "okay";
            compatible = "bl602_i2s";
            reg = <0x40017000 0x100>;
            mclk_only = "okay";
            pin {
                mclk = <11>;
            };
        };
        i2s@40017100 {
            status = "okay";
            compatible = "bl602_i2s";
            reg = <0x40017100 0x100>;
            mclk_only = "disable";
            pin {
                bclk = <12>;
                fs = <29>;
                do = <30>;
                di = <31>;
            };
        };
    };
    i2c {
        #address-cells = <1>;
        #size-cells = <1>;
        i2c@40011000 {
            status = "okay";
            compatible = "bl602_i2c";
            reg = <0x40011000 0x100>;
            pin {
                scl = <32>;
                sda = <13>;
            };
            devices {
                list_addr = <0x18 0x21>;
                list_driver = "i2c_es8311", "i2c_gc0308>";
            };
        };
        i2c@40011100 {
            status = "disable";
            compatible = "bl602_i2c";
            reg = <0x40011100 0x100>;
            pin {
                /*empty here*/
            };
        };
    };
    timer {
        #address-cells = <1>;
        #size-cells = <1>;
        timer@40014000 {
            status = "disable";
            compatible = "bl602_timer";
            reg = <0x40014000 0x100>;
        };
        timer@40014100 {
            status = "disable";
            compatible = "bl602_timer";
            reg = <0x40014100 0x100>;
        };
    };
    pwm {
        #address-cells = <1>;
        #size-cells = <1>;
        pwm@4000A420 {
            status = "okay";
            compatible = "bl602_pwm";
            reg = <0x4000A420 0x20>;
            path = "/dev/pwm0";
            id = <0>;
            pin = <0>;
            freq = <800000>;
            duty = <50>;
        };
        pwm@4000A440 {
            status = "disable";
            reg = <0x4000A440 0x20>;
            path = "/dev/pwm1";
            id = <1>;
            pin = <1>;
            freq = <5000>;
            duty = <50>;
        };
        pwm@4000A460 {
            status = "disable";
            reg = <0x4000A460 0x20>;
            path = "/dev/pwm2";
            id = <2>;
            pin = <2>;
            freq = <5000>;
            duty = <50>;
        };
        pwm@4000A480 {
            status = "disable";
            reg = <0x4000A480 0x20>;
            path = "/dev/pwm3";
            id = <3>;
            pin = <3>;
            freq = <5000>;
            duty = <50>;
        };
        pwm@4000A4A0 {
            status = "disable";
            reg = <0x4000A4A0 0x20>;
            path = "/dev/pwm4";
            id = <4>;
            pin = <4>;
            freq = <5000>;
            duty = <50>;
        };
    };
    ir {
        #address-cells = <1>;
        #size-cells = <1>;
        ctrltype = <0>;
        tx {
            status = "disable";
            pin = <11>;         // only support 11
            mode = "NEC";       // NEC,ExtenedNEC,RC5,SWM
            interval = <100>;   // ms
            active_mode = "Hi"; //Hi,Lo
        };
        rx {
            status = "okay";
            pin = <12>;         // only support 12 13
            mode = "NEC";       // NEC,ExtenedNEC,RC5,SWM
            active_mode = "Hi"; //Hi,Lo
            data_check = <2>;   //bit 0:check cmd, bit 1:check addr
        };
    };
    uart {
        #address-cells = <1>;
        #size-cells = <1>;
        uart@4000A000 {
            status = "okay";
            id = <0>;
            compatible = "bl602_uart";
            path = "/dev/ttyS0";
            baudrate = <2000000>;
            pin {
                rx = <7>;
                tx = <16>;
            };
            buf_size {
                rx_size = <512>;
                tx_size = <512>;
            };
            feature {
                tx = "okay";
                rx = "okay";
                cts = "disable";
                rts = "disable";
            };
        };
        uart@4000A100 {
            status = "okay";
            id = <1>;
            compatible = "bl602_uart";
            path = "/dev/ttyS1";
            baudrate = <115200>;
            pin {
                rx = <3>;
                tx = <4>;
            };
            buf_size {
                rx_size = <512>;
                tx_size = <512>;
            };
            feature {
                tx = "okay";
                rx = "okay";
                cts = "disable";
                rts = "disable";
            };
        };
    };
    spi {
        #address-cells = <1>;
        #size-cells = <1>;
        spi@4000F000 {
            status = "okay";         /* okay disable */
            mode = "master";
            reg = <0x4000F000 0x100>;   /* 4KB */
            path = "/dev/spi0";
            port = <0>;
            polar_phase = <1>;                 /* 0,1,2,3 */
            freq = <6000000>;
            pin {
                clk = <3>;
                cs = <2>;
                mosi = <1>;
                miso = <0>;
            };
            dma_cfg {
                tx_dma_ch = <2>;
                rx_dma_ch = <3>;
            };
        };
    };
    gpip {
        #address-cells = <1>;
        #size-cells = <1>;
        adc_key {
            status = "disable";
            pin = <9>;
            interrupt  = <3>;
            key_vol = <0 100 400 300 500>;
            key_pcb = "SW1", "SW2", "SW3", "SW4","SW5";
            key_event = "Usr1", "Usr2", "Start", "Up", "Down";
            key_raw = <1 2 3 4 5>;
        };
    };
    qspi {
        #address-cells = <1>;
        #size-cells = <1>;
        qspi@4000A000 {
            status = "disable";
            reg = <0x4000A000 0x1000>;/* 4KB */
        };
    };
    wifi {
        #address-cells = <1>;
        #size-cells = <1>;
        region {
            country_code = <86>;
        };
        mac {
            mode = "MBF";
            sta_mac_addr = [C8 43 57 82 73 40];
            ap_mac_addr = [C8 43 57 82 73 02];
        };
        sta {
            ssid = "yourssid";
            pwd = "yourapssword";
            auto_connect_enable = <0>;
        };
        ap {
            ssid = "bl_test_005";
            pwd = "12345678";
            ap_channel = <11>;
            auto_chan_detect = "disable";
        };
        brd_rf {
            xtal_mode = "MF";
            xtal = <36 36 0 60 60>;
            /*
            pwr_table = <   4 3 3 186
                            4 3 4 176
                            4 3 5 167
                            3 3 0 159
                            3 3 1 149
                            3 3 2 140
                            3 3 3 129
                            3 3 4 119
                            3 3 5 110
                            2 3 0 101
                            2 3 1 91
                            2 3 2 82
                            2 3 3 72
                            2 3 4 62
                            2 3 5 52
                            1 3 3 10>;
            */
            pwr_mode = "bf";//B: only use power offset in EFUSE; b: use power offset in EFUSE with incremental mode; F: only use power offset in Flash; f: use power offset in Flash with incremental mode
            pwr_table_11b = <20 20 20 18>;//1Mbps 2Mbps 5.5Mbps 11Mbps
            pwr_table_11g = <18 18 18 18 18 18 14 14>; //6Mbps 9Mbps 12Mbps 18MBps 24Mbps 36Mbps 48Mbps 54Mbps
            pwr_table_11n = <18 18 18 18 18 16 14 14>; //MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7
            pwr_offset = <10 10 10 10 10 10 10 10 10 10 10 10 10 10>;//due to the limit of current DTC, negative value is used. So we work around by adding all the poweroffset with 10. so 8 represents -2; 10 represents 0; 13 represents 3
        };
        rf_temp {
            en_tcal = <0>;
            linear_or_follow = <1>;
            Tchannels       = <2412 2427 2442 2457 2472>;
            Tchannel_os     = <180  168  163  160  157>;
            Tchannel_os_low = <199  186  170  165  160>;
            Troom_os        = <255>;
            //negative value is NOT supported. So we use '256' for 0, '255' for -1, '257' for 1,'511' for 256
        };
    };
    bluetooth {
        #address-cells = <1>;
        #size-cells = <1>;
        brd_rf {
            pwr_table_ble = <13>;  //range:0~15dbm
        };
    };
    MFD {
        vendor_name = "Bouffalo Lab";
        vendor_id = [0x0d 0x13];
        product_name = "Test Device";
        product_id = [0x01 0xf0];
        product_part_number = "Test Part Number";
        product_url = "Test Product URL";
        product_label = "Test Product Label";
        manufactoring_date = <2023 02 26>;
        hardware_version = [0x01 0x00];
        hardware_version_string = "ver_0.1";
    };
};
};