# Copyright (c) 2021 Project CHIP Authors
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.

name: 42.2.2. [TC-TSTAT-2.2] Setpoint Test Cases with server as DUT

PICS:
    - TSTAT.S

config:
    nodeId: 0x12344321
    cluster: "Thermostat"
    endpoint: 1

tests:
    - label: "Step 1: Commission DUT to TH"
      cluster: "DelayCommands"
      command: "WaitForCommissionee"
      arguments:
          values:
              - name: "nodeId"
                value: nodeId

    - label: "Saving value for comparision in step 2a read MinCoolSetpointLimit"
      PICS: TSTAT.S.A0017
      command: "readAttribute"
      attribute: "MinCoolSetpointLimit"
      response:
          saveAs: MinCoolSetpointLimitValue

    - label: "Saving value for comparision in step 2a read MaxCoolSetpointLimit"
      PICS: TSTAT.S.A0018
      command: "readAttribute"
      attribute: "MaxCoolSetpointLimit"
      response:
          saveAs: MaxCoolSetpointLimitValue

    - label:
          "Saving value for comparision in step 2c read attribute
          MinSetpointDeadBand"
      PICS: TSTAT.S.A0019
      command: "readAttribute"
      attribute: "MinSetpointDeadBand"
      response:
          saveAs: MinSetpointDeadBandValue

    - label: "Saving value for comparision in step 3a read MinHeatSetpointLimit"
      PICS: TSTAT.S.A0015
      command: "readAttribute"
      attribute: "MinHeatSetpointLimit"
      response:
          saveAs: MinHeatSetpointLimitValue

    - label:
          "Saving value for comparision in step 3 reads
          UnoccupiedCoolingSetpoint attribute"
      command: "readAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.A0013
      response:
          saveAs: UnoccupiedCoolingSetpointValue

    - label: "Saving value for comparision in step 3a read MaxHeatSetpointLimit"
      PICS: TSTAT.S.A0016
      command: "readAttribute"
      attribute: "MaxHeatSetpointLimit"
      response:
          saveAs: MaxHeatSetpointLimitValue

    - label:
          "Saving value for comparision in step3c read attribute
          OccupiedHeatingSetpoint"
      PICS: TSTAT.S.A0012
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      response:
          saveAs: OccupiedHeatingSetpointValue

    - label:
          "Saving value for comparision in step3c read attribute
          OccupiedCoolingSetpoint"
      PICS: TSTAT.S.A0011
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      response:
          saveAs: OccupiedCoolingSetpointValue

    - label:
          "Saving value for comparision in step 6a read attribute
          AbsMinHeatSetpointLimit"
      command: "readAttribute"
      attribute: "AbsMinHeatSetpointLimit"
      PICS: TSTAT.S.A0003
      response:
          saveAs: AbsMinHeatSetpointLimitValue

    - label:
          "Saving value for comparision in step 7a read attribute
          AbsMaxHeatSetpointLimit"
      command: "readAttribute"
      attribute: "AbsMaxHeatSetpointLimit"
      PICS: TSTAT.S.A0004
      response:
          saveAs: AbsMaxHeatSetpointLimitValue

    - label:
          "Saving value for comparision in step 8a read attribute
          AbsMinCoolSetpointLimit"
      command: "readAttribute"
      attribute: "AbsMinCoolSetpointLimit"
      PICS: TSTAT.S.A0005
      response:
          saveAs: AbsMinCoolSetpointLimitValue

    - label:
          "Saving value for comparision in step9a read attribute
          AbsMaxCoolSetpointLimit"
      command: "readAttribute"
      attribute: "AbsMaxCoolSetpointLimit"
      PICS: TSTAT.S.A0006
      response:
          saveAs: AbsMaxCoolSetpointLimitValue

    #Using saved values when optional attributes are available
    - label:
          "Step 2a: Test Harness Client reads  attribute OccupiedCoolingSetpoint
          from the DUT"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0018
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      response:
          constraints:
              type: int16s
              minValue: MinCoolSetpointLimitValue
              maxValue: MaxCoolSetpointLimitValue

    #Using hard coded values when optional attributes are not available
    - label:
          "Step 2a: Test Harness Client reads OccupiedCoolingSetpoint attribute
          from Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && !TSTAT.S.A0017 && !TSTAT.S.A0018
      response:
          constraints:
              type: int16s
              minValue: 1600
              maxValue: 3200

    - label:
          "Step 2a: Test Harness Client then attempts Writes a value back that
          is different but valid for OccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      arguments:
          value: 2500

    - label:
          "Step 2a: Test Harness Client reads it back again to confirm the
          successful write of OccupiedCoolingSetpoint attribute"
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      response:
          value: 2500

    - label:
          "Step 2b: Test Harness Client then attempts  Writes
          OccupiedCoolingSetpoint to value below the MinCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && !TSTAT.S.A0017
      arguments:
          value: 30
      response:
          error: CONSTRAINT_ERROR

    #MinCoolSetPointLimit might be negative if not checked before decrement
    - label:
          "Step 2b: Test Harness Writes OccupiedCoolingSetpoint to value below
          the MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #2 Test Harness Client  attempts to write OccupiedCoolingSetpoint below the MinCoolSetpointLimit and confirms that the device does not accept the value.
          ./chip-tool thermostat write occupied-cooling-setpoint 1000 1 1
          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87) for the value which is below of the  MinCoolSetpointLimitValue

          [1676028984.901635][19375:19377] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676028984.901706][19375:19377] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676028984.901895][19375:19377] CHIP:EM: <<< [E:18153i M:141749864 (Ack:137408936)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
          [1676028984.901980][19375:19377] CHIP:IN: (S) Sending msg 141749864 on secure session with LSID: 58847
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 2b: Test Harness Writes OccupiedCoolingSetpoint to value above
          the MaxCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && !TSTAT.S.A0017
      arguments:
          value: 4000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 2b: Test Harness Writes OccupiedCoolingSetpoint to value above
          the MaxCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017
      arguments:
          value: MaxCoolSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 2c: Test Harness Writes the limit of MaxCoolSetpointLimit to
          OccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && !TSTAT.S.A0017
      arguments:
          value: 3200

    - label:
          "Step 2c: Test Harness Writes the limit of MaxCoolSetpointLimit to
          OccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017
      arguments:
          value: MaxCoolSetpointLimitValue

    - label:
          "Step 2c:  Test Harness Writes the limit of MinCoolSetpointLimit to
          OccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && !TSTAT.S.F05 && !TSTAT.S.A0017
      arguments:
          value: 1600

    - label:
          "Step 2c:  Test Harness Writes the limit of MinCoolSetpointLimit to
          OccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01 && !TSTAT.S.F05 && TSTAT.S.A0017
      arguments:
          value: MinCoolSetpointLimitValue

    #LowerLimit = Max(MinCoolSetpointLimit,(OccupiedHeatingSetpoint + MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 2c:  Test Harness Writes If TSTAT.S.F05(AUTO) LowerLimit =
          Max(MinCoolSetpointLimit, (OccupiedHeatingSetpoint +
          MinSetpointDeadBand)) to OccupiedCoolingSetpoint attribute when Auto
          is enabled"
      PICS: TSTAT.S.F05 && TSTAT.S.A0011 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          Test Harness Client then attempts to write OccupiedCoolingSetpoint to both of the limits of LowerLimit(1600) & MaxCoolSetpointLimit(3200) and confirms that the device does accept the value. See also Note 5.

          ./chip-tool thermostat write occupied-cooling-setpoint 1600 1 1
          On TH(chip-tool) verify that  DUT sends a success response
          [1676029009.026653][19381:19383] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029009.026688][19381:19383] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676029009.026776][19381:19383] CHIP:EM: <<< [E:29492i M:142792974 (Ack:241003612)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    #Using saved values when optional attributes are available
    - label:
          "Step 3a:  Test Harness Reads OccupiedHeatingSetpoint attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && TSTAT.S.A0016
      response:
          constraints:
              type: int16s
              minValue: MinHeatSetpointLimitValue
              maxValue: MaxHeatSetpointLimitValue

    #Using hard coded values when optional attributes are not available
    - label:
          "Step 3a:  Test Harness Reads OccupiedHeatingSetpoint attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && !TSTAT.S.A0015 && !TSTAT.S.A0016
      response:
          constraints:
              type: int16s
              minValue: 700
              maxValue: 3000

    - label:
          "Step 3a:  Test Harness Writes a value back that is different but
          valid for OccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      arguments:
          value: 2100

    - label:
          "Step 3a:  Test Harness Reads it back again to confirm the successful
          write of OccupiedHeatingSetpoint attribute"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      response:
          value: 2100

    - label:
          "Step 3b:  Test Harness Writes OccupiedHeatingSetpoint to value below
          the MinHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && !TSTAT.S.A0015
      arguments:
          value: 100
      response:
          error: CONSTRAINT_ERROR

    #MinHeatSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 3b:  Test Harness Writes OccupiedHeatingSetpoint to value below
          the MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #1. Test Harness Client attempts to write OccupiedHeatingSetpoint below the MinHeatSetpointLimit and confirms that the device does not accept the value

          ./chip-tool thermostat write  occupied-heating-setpoint 500 1 1
          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87)
          [1676029113.651245][19392:19394] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029113.651285][19392:19394] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676029113.651397][19392:19394] CHIP:EM: <<< [E:43315i M:59735604 (Ack:107613834)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 3b:  Test Harness Writes OccupiedHeatingSetpoint to value above
          the MaxHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && !TSTAT.S.A0016
      arguments:
          value: 4010
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 3b:  Test Harness Writes OccupiedHeatingSetpoint to value above
          the MaxHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016
      arguments:
          value: MaxHeatSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 3c:  Test Harness Writes the limit of MaxHeatSetpointLimit to
          OccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && !TSTAT.S.F05 && !TSTAT.S.A0016
      arguments:
          value: 3000

    - label:
          "Step 3c:  Test Harness Writes the limit of MaxHeatSetpointLimit to
          OccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && !TSTAT.S.F05 && TSTAT.S.A0016
      arguments:
          value: MaxHeatSetpointLimitValue

    - label:
          "Step 3c:  Test Harness Writes the limit of MaxHeatSetpointLimit to
          OccupiedHeatingSetpoint attribute If TSTAT.S.F05 is true"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F05 && !TSTAT.S.A0015
      arguments:
          value: 3000
      response:
          error: CONSTRAINT_ERROR

    #UpperLimit = Min(MaxHeatSetpointLimit,(OccupiedCoolingSetpoint - MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 3c:  Test Harness Writes If TSTAT.S.F05(AUTO) UpperLimit =
          Min(MaxHeatSetpointLimit, (OccupiedCoolingSetpoint -
          MinSetpointDeadBand)) to OccupiedHeatingSetpoint attribute when Auto
          is enabled"
      PICS:
          TSTAT.S.F05 && TSTAT.S.A0011 && TSTAT.S.A0012 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          Test Harness Client then attempts to write OccupiedHeatingSetpoint to both of the limits of MinHeatSetpointLimit(700) & UpperLimit(3000) and confirms that the device does accept the value.

          ./chip-tool thermostat write occupied-heating-setpoint 3000 1 1

          On TH(chip-tool) verify that  DUT sends a success response
          1676029222.303920][19403:19405] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029222.303955][19403:19405] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676029222.304055][19403:19405] CHIP:EM: <<< [E:236i M:251820549 (Ack:138263425)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10

          ./chip-tool thermostat write occupied-heating-setpoint 700 1 1
          On TH(chip-tool) verify that  DUT sends a success response


          [1678943387.942204][770598:770600] CHIP:DMG:                         StatusIB =
          [1678943387.942212][770598:770600] CHIP:DMG:                         {
          [1678943387.942220][770598:770600] CHIP:DMG:                                 status = 0x00 (SUCCESS),
          [1678943387.942228][770598:770600] CHIP:DMG:                         },
          [1678943387.942236][770598:770600] CHIP:DMG:
          [1678943387.942243][770598:770600] CHIP:DMG:                 },
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 3c:  Test Harness Writes the limit of MinHeatSetpointLimit to
          OccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && !TSTAT.S.A0015
      arguments:
          value: 700

    - label:
          "Step 3c:  Test Harness Writes the limit of MinHeatSetpointLimit to
          OccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015
      arguments:
          value: MinHeatSetpointLimitValue

    - label:
          "Step 4a:  Test Harness Reads UnoccupiedCoolingSetpoint attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0018
      response:
          constraints:
              type: int16s
              minValue: MinCoolSetpointLimitValue
              maxValue: MaxCoolSetpointLimitValue

    - label:
          "Step 4a:  Test Harness Reads UnoccupiedCoolingSetpoint attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && !TSTAT.S.A0017 && !TSTAT.S.A0018
      response:
          constraints:
              type: int16s
              minValue: 1600
              maxValue: 3200

    - label:
          "Step 4a:  Test Harness Writes a value back that is different but
          valid for UnoccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01
      arguments:
          value: 2500

    - label:
          "Step 4a:  Test Harness Reads it back again to confirm the successful
          write of UnoccupiedCoolingSetpoint attribute"
      command: "readAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01
      response:
          value: 2500

    - label:
          "Step 4b:  Test Harness Writes UnoccupiedCoolingSetpoint to value
          below the MinCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && !TSTAT.S.A0017
      arguments:
          value: 500
      response:
          error: CONSTRAINT_ERROR

    #MinCoolSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 4b:  Test Harness Writes UnoccupiedCoolingSetpoint to value
          below the MinCoolSetpointLimit"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && TSTAT.S.A0017 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #1. Test Harness Client attempts to write OccupiedHeatingSetpoint below the MinHeatSetpointLimit and confirms that the device does not accept the value

          ./chip-tool thermostat write  unoccupied-cooling-setpoint 500 1 1
          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87)
          [1676029263.842915][19409:19411] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029263.842943][19409:19411] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676029263.843052][19409:19411] CHIP:EM: <<< [E:47350i M:72320003 (Ack:188090912)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 4b:  Test Harness Writes UnoccupiedCoolingSetpoint to value
          above the MaxCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && !TSTAT.S.A0018
      arguments:
          value: 4010
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 4b:  Test Harness Writes UnoccupiedCoolingSetpoint to value
          above the MaxCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && TSTAT.S.A0018
      arguments:
          value: MaxCoolSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 4c:  Test Harness Writes the limit of MaxCoolSetpointLimit to
          UnoccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && !TSTAT.S.A0018 && !TSTAT.S.F05
      arguments:
          value: 3200

    - label:
          "Step 4c:  Test Harness Writes the limit of MaxCoolSetpointLimit to
          UnoccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.F05
      arguments:
          value: MaxCoolSetpointLimitValue

    #LowerLimit = Max(MinCoolSetpointLimit,(UnoccupiedCoolingSetpoint + MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 4c:  Test Harness Writes If TSTAT.S.F05(AUTO) LowerLimit =
          Max(MinCoolSetpointLimit, (UnoccupiedCoolingSetpoint +
          MinSetpointDeadBand)) to UnoccupiedCoolingSetpoint attribute"
      PICS:
          TSTAT.S.F02 && TSTAT.S.F01 && TSTAT.S.A0013 && TSTAT.S.F05 &&
          PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.


          below mentioned the example command to verify

          ./chip-tool thermostat write unoccupied-cooling-setpoint 2000  1 1
          On TH(chip-tool) verify that  DUT sends a success response.  As its an optional attribute, we are not getting expected result
          [1676029365.250210][19420:19422] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029365.250263][19420:19422] CHIP:TOO: Response Failure: IM Error 0x00000586: General error: 0x86 (UNSUPPORTED_ATTRIBUTE)
          [1676029365.250403][19420:19422] CHIP:EM: <<< [E:16230i M:267641165 (Ack:117850882)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
          [1676029365.250467][19420:19422] CHIP:IN: (S) Sending msg 267641165 on secure session with LSID: 45606
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 4c:  Test Harness Writes the limit of MinCoolSetpointLimit to
          UnoccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && !TSTAT.S.A0017 && !TSTAT.S.F05
      arguments:
          value: 1600

    - label:
          "Step 4c:  Test Harness Writes the limit of MinCoolSetpointLimit to
          UnoccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && !TSTAT.S.A0017 && TSTAT.S.F05
      arguments:
          value: 1600
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 4c:  Test Harness Writes the limit of MinCoolSetpointLimit to
          UnoccupiedCoolingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedCoolingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.F05
      arguments:
          value: MinCoolSetpointLimitValue

    #Using saved values when optional attributes are available
    - label:
          "Step 5a:  Test Harness Reads UnoccupiedHeatingSetpoint attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && TSTAT.S.A0015 && TSTAT.S.A0016
      response:
          constraints:
              type: int16s
              minValue: MinHeatSetpointLimitValue
              maxValue: MaxHeatSetpointLimitValue

    #Using hardcoded values when optional attributes are not available
    - label:
          "Step 5a:  Test Harness Reads UnoccupiedHeatingSetpoint attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && !TSTAT.S.A0015 && !TSTAT.S.A0016
      response:
          constraints:
              type: int16s
              minValue: 700
              maxValue: 3000

    - label:
          "Step 5a:  Test Harness Writes a value back that is different but
          valid for UnoccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00
      arguments:
          value: 2500

    - label:
          "Step 5a:  Test Harness Reads it back again to confirm the successful
          write of UnoccupiedHeatingSetpoint attribute"
      command: "readAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00
      response:
          value: 2500

    - label:
          "Step 5b:  Test Harness Writes UnoccupiedHeatingSetpoint to value
          below the MinHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && !TSTAT.S.A0015
      arguments:
          value: 100
      response:
          error: CONSTRAINT_ERROR

    #MinHeatSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 5b:  Test Harness Writes UnoccupiedHeatingSetpoint to value
          below the MinHeatSetpointLimit"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && TSTAT.S.A0015 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #1. Test Harness Client  attempts to write UnoccupiedHeatingSetpoint below the MinHeatSetpointLimit and confirms that the device does not accept the value

          ./chip-tool thermostat write  unoccupied-heating-setpoint 500 1 1
          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87). As its an optional attribute, we are not getting expected result

          [1676029557.268065][19431:19433] CHIP:DMG: }
          [1676029557.268220][19431:19433] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029557.268290][19431:19433] CHIP:TOO: Response Failure: IM Error 0x00000586: General error: 0x86 (UNSUPPORTED_ATTRIBUTE)
          [1676029557.268470][19431:19433] CHIP:EM: <<< [E:8458i M:31631638 (Ack:115187982)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 5b:  Test Harness Writes UnoccupiedHeatingSetpoint to value
          above the MaxHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && !TSTAT.S.A0016
      arguments:
          value: 4010
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 5b:  Test Harness Writes UnoccupiedHeatingSetpoint to value
          above the MaxHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && TSTAT.S.A0016
      arguments:
          value: MaxHeatSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 5c:  Test Harness Writes the limit of MaxHeatSetpointLimit to
          UnoccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && !TSTAT.S.A0016 && !TSTAT.S.F05
      arguments:
          value: 3000

    - label:
          "Step 5c:  Test Harness Writes the limit of MaxHeatSetpointLimit to
          UnoccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && TSTAT.S.A0016 && !TSTAT.S.F05
      arguments:
          value: MaxHeatSetpointLimitValue

    - label:
          "Step 5c:  Test Harness Writes the limit of MaxHeatSetpointLimit to
          UnoccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && !TSTAT.S.A0016 && TSTAT.S.F05
      arguments:
          value: 3000
      response:
          error: CONSTRAINT_ERROR

    #UpperLimit = Min(MaxHeatSetpointLimit,(UnoccupiedCoolingSetpoint - MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 5c:  Test Harness Writes If TSTAT.S.F05(AUTO) UpperLimit =
          Min(MaxHeatSetpointLimit, (UnoccupiedCoolingSetpoint -
          MinSetpointDeadBand)) to UnoccupiedHeatingSetpoint attribute when Auto
          is enabled."
      PICS:
          TSTAT.S.F02 && TSTAT.S.F00 && TSTAT.S.A0013 && TSTAT.S.F05 &&
          PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.


          below mentioned the example command to verify

          ./chip-tool thermostat write unoccupied-heating-setpoint 2000  1 1
          On TH(chip-tool) verify that  DUT sends a success response.  As its an optional attribute, we are not getting expected result

          [1676029629.242182][19437:19439] CHIP:DMG: }
          [1676029629.242250][19437:19439] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029629.242280][19437:19439] CHIP:TOO: Response Failure: IM Error 0x00000586: General error: 0x86 (UNSUPPORTED_ATTRIBUTE)
          [1676029629.242366][19437:19439] CHIP:EM: <<< [E:51650i M:149591010 (Ack:214538556)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
          [1676029629.242402][19437:19439] CHIP:IN: (S) Sending msg 149591010 on secure session with LSID: 6132
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 5c:  Test Harness Writes the limit of MinHeatSetpointLimit to
          UnoccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && !TSTAT.S.A0015
      arguments:
          value: 700

    - label:
          "Step 5c:  Test Harness Writes the limit of MinHeatSetpointLimit to
          UnoccupiedHeatingSetpoint attribute"
      command: "writeAttribute"
      attribute: "UnoccupiedHeatingSetpoint"
      PICS: TSTAT.S.F02 && TSTAT.S.F00 && TSTAT.S.A0015
      arguments:
          value: MinHeatSetpointLimitValue

    #Using saved values when optional attributes are available
    - label:
          "Step 6a:  Test Harness Reads MinHeatSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && TSTAT.S.A0016 && TSTAT.S.A0003
      response:
          constraints:
              type: int16s
              minValue: AbsMinHeatSetpointLimitValue
              maxValue: MaxHeatSetpointLimitValue

    #Using hard coded values when optional attributes are not available
    - label:
          "Step 6a: Test Harness Reads MinHeatSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && !TSTAT.S.A0016 && !TSTAT.S.A0003
      response:
          constraints:
              type: int16s
              minValue: 700
              maxValue: 3000

    - label:
          "Step 6a: Test Harness Writes a value back that is different but valid
          for MinHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015
      arguments:
          value: 800

    - label:
          "Step 6a: Test Harness Reads it back again to confirm the successful
          write of MinHeatSetpointLimit attribute"
      command: "readAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015
      response:
          value: 800

    - label:
          "Step 6b: Test Harness Writes a value back that is different but
          violates the deadband"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.A0015 && TSTAT.S.F05
      arguments:
          value: 2000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 6b: Test Harness Writes MinHeatSetpointLimit to value below the
          AbsMinHeatSetpointLimit "
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && !TSTAT.S.A0003
      arguments:
          value: 100
      response:
          error: CONSTRAINT_ERROR

    #AbsMinHeatSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 6b: Test Harness Writes MinHeatSetpointLimit to value below the
          AbsMinHeatSetpointLimit "
      PICS:
          TSTAT.S.F00 && TSTAT.S.A0015 && TSTAT.S.A0003 && PICS_SKIP_SAMPLE_APP
      verification: |
          #1. Test Harness Client  attempts to write MinHeatSetpointLimit below the AbsMinHeatSetpointLimit and confirms that the device does not accept the value.
          ./chip-tool thermostat write min-heat-setpoint-limit 300  1 1
          On TH  (chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87)
          [1676029705.839179][19450:19452] CHIP:DMG: }
          [1676029705.839253][19450:19452] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029705.839287][19450:19452] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676029705.839411][19450:19452] CHIP:EM: <<< [E:34538i M:185292291 (Ack:127655640)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
          [1676029705.839456][19450:19452] CHIP:IN: (S) Sending msg 185292291 on secure session with LSID: 61694
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 6b: Test Harness Writes MinHeatSetpointLimit to value above the
          AbsMaxHeatSetpointLimit "
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015 && !TSTAT.S.A0016
      arguments:
          value: 4050
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 6b: Test Harness Writes MinHeatSetpointLimit to value above the
          AbsMaxHeatSetpointLimit "
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015 && TSTAT.S.A0016
      arguments:
          value: MaxHeatSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 6c: Test Harness Writes the limit of MaxHeatSetpointLimit to
          MinHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015 && !TSTAT.S.F05 && !TSTAT.S.A0016
      arguments:
          value: 3000

    - label:
          "Step 6c: Test Harness Writes the limit of MaxHeatSetpointLimit to
          MinHeatSetpointimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015 && !TSTAT.S.F05 && TSTAT.S.A0016
      arguments:
          value: MaxHeatSetpointLimitValue

    #UpperLimit = Min(MaxHeatSetpointLimit,(MinCoolSetpointLimit - MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 6c: Test Harness Writes If TSTAT.S.F05(AUTO) UpperLimit =
          Min(MaxHeatSetpointLimit, (MinCoolSetpointLimit -
          MinSetpointDeadBand)) to MinHeatSetpointLimit attribute when Auto is
          enabled"
      PICS:
          TSTAT.S.F00  && TSTAT.S.A0015 && TSTAT.S.F05 && TSTAT.S.A0005 &&
          PICS_SKIP_SAMPLE_APP
      verification: |
          Test Harness Client then attempts to write MinHeatSetpointLimit to both of the limits of AbsMinHeatSetpointLimit & UpperLimit and confirms that the device does accept the value.
          below is an exaple command.

          ./chip-tool thermostat write min-heat-setpoint-limit 1200  1 1

          On TH(chip-tool) verify that  DUT sends a success response

          [1676029742.329801][19458:19460] CHIP:DMG:                         }
          [1676029742.329846][19458:19460] CHIP:DMG:
          [1676029742.329883][19458:19460] CHIP:DMG:                         StatusIB =
          [1676029742.329922][19458:19460] CHIP:DMG:                         {
          [1676029742.329962][19458:19460] CHIP:DMG:                                 status = 0x00 (SUCCESS),
          [1676029742.330001][19458:19460] CHIP:DMG:                         },
          [1676029742.330040][19458:19460] CHIP:DMG:
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 6c: Test Harness Writes the limit of AbsMinHeatSetpointLimit to
          MinHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015 && !TSTAT.S.A0003
      arguments:
          value: 700

    - label:
          "Step 6c: Test Harness Writes the limit of AbsMinHeatSetpointLimit to
          MinHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015 && TSTAT.S.A0003
      arguments:
          value: AbsMinHeatSetpointLimitValue

    #Using saved values when optional attributes are available
    - label:
          "Step 7a: Test Harness Reads MaxHeatSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS:
          TSTAT.S.F00  && TSTAT.S.A0016 && !TSTAT.S.F05 && TSTAT.S.A0004 &&
          TSTAT.S.A0016
      response:
          constraints:
              type: int16s
              minValue: MinHeatSetpointLimitValue
              maxValue: AbsMaxHeatSetpointLimitValue

    #Using hard coded values when optional attributes are not available
    - label:
          "Step 7a: Test Harness Reads MaxHeatSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS:
          " TSTAT.S.F00  && TSTAT.S.A0016 && !TSTAT.S.F05 && !TSTAT.S.A0004 &&
          !TSTAT.S.A0016 "
      response:
          constraints:
              type: int16s
              minValue: 700
              maxValue: 3000

    - label:
          "Step 7b: Test Harness Writes the limit of AbsMinHeatSetpointLimit to
          MinHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0015
      arguments:
          value: 700

    - label:
          "Step 7b: Test Harness Writes the limit of AbsMaxHeatSetpointLimit to
          MinHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.A0015 && TSTAT.S.F05
      arguments:
          value: 3000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 7b: Test Harness Writes a value back that is different but valid
          for MaxHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && !TSTAT.S.F05
      arguments:
          value: 2900

    - label:
          "Step 7b: Test Harness Reads it back again to confirm the successful
          write of MaxHeatSetpointLimit attribute"
      command: "readAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && !TSTAT.S.F05
      response:
          value: 2900

    - label:
          "Step 7b: Test Harness Writes MaxHeatSetpointLimit to value below the
          AbsMinHeatSetpointLimit "
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0016 && !TSTAT.S.A0015
      arguments:
          value: 100
      response:
          error: CONSTRAINT_ERROR

    #MinHeatSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 7b: Test Harness Writes MaxHeatSetpointLimit to value below the
          MinHeatSetpointLimit"
      PICS:
          TSTAT.S.F00  && TSTAT.S.A0016 && TSTAT.S.A0015 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #1. Test Harness Client  attempts to write MaxHeatSetpointLimit below the MinHeatSetpointLimit and confirms that the device does not accept the value.
          ./chip-tool thermostat write  max-heat-setpoint-limit 100 1 1
          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87)
          [1676029976.380552][19475:19477] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676029976.380598][19475:19477] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676029976.380705][19475:19477] CHIP:EM: <<< [E:10254i M:97110781 (Ack:264765613)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 7b: Test Harness Writes MaxHeatSetpointLimit to value above the
          AbsMaxHeatSetpointLimit "
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0016 && !TSTAT.S.A0004
      arguments:
          value: 4000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 7b: Test Harness Writes MaxHeatSetpointLimit to value above the
          AbsMaxHeatSetpointLimit "
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0016 && TSTAT.S.A0004
      arguments:
          value: AbsMaxHeatSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 7c: Test Harness Writes the limit of AbsMaxHeatSetpointLimit to
          MaxHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0016 && !TSTAT.S.F05 && !TSTAT.S.A0004
      arguments:
          value: 3000

    - label:
          "Step 7c: Test Harness Writes the limit of AbsMaxHeatSetpointLimit to
          MaxHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && !TSTAT.S.F05 && TSTAT.S.A0004
      arguments:
          value: AbsMaxHeatSetpointLimitValue

    #UpperLimit = Min(AbsMaxHeatSetpointLimit,(MaxCoolSetpointLimit - MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 7c: Test Harness Writes If TSTAT.S.F05(AUTO) UpperLimit =
          Min(AbsMaxHeatSetpointLimit, (MaxCoolSetpointLimit -
          MinSetpointDeadBand)) to MaxHeatSetpointLimit attribute"
      PICS:
          TSTAT.S.F00 && TSTAT.S.A0016 && TSTAT.S.F05 && TSTAT.S.A0018 &&
          PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation

          Test Harness Client then attempts to write MaxHeatSetpointLimit to both of the limits of MinHeatSetpointLimit & UpperLimit and confirms that the device does accept the value.

          below is an examble command

          ./chip-tool thermostat write  max-heat-setpoint-limit 2000( Consider the different value but valid4) 1 1
          On TH(chip-tool) verify that  DUT sends a success response

          [1676030018.852009][19481:19483] CHIP:DMG:                                 Cluster = 0x201,
          [1676030018.852054][19481:19483] CHIP:DMG:                                 Attribute = 0x0000_0016,
          [1676030018.852094][19481:19483] CHIP:DMG:                         }
          [1676030018.852138][19481:19483] CHIP:DMG:
          [1676030018.852178][19481:19483] CHIP:DMG:                         StatusIB =
          [1676030018.852218][19481:19483] CHIP:DMG:                         {
          [1676030018.852258][19481:19483] CHIP:DMG:                                 status = 0x00 (SUCCESS),
          [1676030018.852297][19481:19483] CHIP:DMG:                         },
          [1676030018.852337][19481:19483] CHIP:DMG:
          [1676030018.852370][19481:19483] CHIP:DMG:                 },
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 7c: Test Harness Writes the limit of MinHeatSetpointLimit to
          MaxHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00  && TSTAT.S.A0016 && !TSTAT.S.A0015
      arguments:
          value: 700

    - label:
          "Step 7c: Test Harness Writes the limit of MinHeatSetpointLimit to
          MaxHeatSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && TSTAT.S.A0015
      arguments:
          value: MinHeatSetpointLimitValue

    #Using saved values when optional attributes are available
    - label:
          "Step 8a: Test Harness Reads MinCoolSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0018 && TSTAT.S.A0005
      response:
          constraints:
              type: int16s
              minValue: AbsMinCoolSetpointLimitValue
              maxValue: MaxCoolSetpointLimitValue

    #Using hard coded values when optional attributes are not available
    - label:
          "Step 8a: Test Harness Reads MinCoolSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.A0018 && !TSTAT.S.A0005
      response:
          constraints:
              type: int16s
              minValue: 1600
              maxValue: 3200

    - label:
          "Step 8a: Test Harness Writes a value back that is different but valid
          for MinCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017
      arguments:
          value: 2000

    - label:
          "Step 8a: Test Harness Reads it back again to confirm the successful
          write of MinCoolSetpointLimit attribute"
      command: "readAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017
      response:
          value: 2000

    - label:
          "Step 8b: Test Harness Writes MinCoolSetpointLimit to value below the
          AbsMinCoolSetpointLimit "
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.A0005
      arguments:
          value: 500
      response:
          error: CONSTRAINT_ERROR

    #AbsMinCoolSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 8b: Test Harness Writes MinCoolSetpointLimit to value below the
          AbsMinCoolSetpointLimit"
      PICS:
          TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0005 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #1. Test Harness Client then attempts to write MinCoolSetpointLimit below the AbsMinCoolSetpointLimit  and confirms that the device does not accept the value.

          ./chip-tool thermostat write min-cool-setpoint-limit 400  1 1

          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87)
          [1676030095.274876][19495:19497] CHIP:DMG: }
          [1676030095.274936][19495:19497] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676030095.274965][19495:19497] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676030095.275097][19495:19497] CHIP:EM: <<< [E:51146i M:60043723 (Ack:28649429)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"
    - label:
          "Step 8b: Test Harness Writes MinCoolSetpointLimit to value above the
          MaxCoolSetpointLimit "
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.A0018
      arguments:
          value: 4000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 8b: Test Harness Writes MinCoolSetpointLimit to value above the
          MaxCoolSetpointLimit "
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0018
      arguments:
          value: MaxCoolSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 8c: Test Harness Writes the limit of MaxCoolSetpointLimit to
          MinCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.A0018
      arguments:
          value: 3200

    - label:
          "Step 8c: Test Harness Writes the limit of MaxCoolSetpointLimit to
          MinCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0018
      arguments:
          value: MaxCoolSetpointLimitValue

    - label:
          "Step 8c: Test Harness Writes the limit of AbsMinCoolSetpointLimit to
          MinCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.A0005 && !TSTAT.S.F05
      arguments:
          value: 1600

    - label:
          "Step 8c: Test Harness Writes the limit of AbsMinCoolSetpointLimit to
          MinCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0005 && !TSTAT.S.F05
      arguments:
          value: AbsMinCoolSetpointLimitValue

    #LowerLimit = Max(AbsMinCoolSetpointLimit,(MinHeatSetpointLimit + MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 8c: Test Harness Writes If TSTAT.S.F05(AUTO) LowerLimit =
          Max(AbsMinCoolSetpointLimit, (MinHeatSetpointLimit +
          MinSetpointDeadBand)) to MinCoolSetpointLimit attribute"
      PICS:
          TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0015 && TSTAT.S.F05 &&
          PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          Test Harness Client then attempts to write MinCoolSetpointLimit to both of the limits of LowerLimit & MaxCoolSetpointLimit and confirms that the device does accept the value.

          ./chip-tool thermostat write min-cool-setpoint-limit 1600 1 1

          On TH(chip-tool) verify that  DUT sends a success response

          [1678947233.814534][773656:773658] CHIP:DMG:
          [1678947233.814541][773656:773658] CHIP:DMG:                         StatusIB =
          [1678947233.814548][773656:773658] CHIP:DMG:                         {
          [1678947233.814555][773656:773658] CHIP:DMG:                                 status = 0x00 (SUCCESS),
          [1678947233.814562][773656:773658] CHIP:DMG:                         },
          [1678947233.814570][773656:773658] CHIP:DMG:
          [1678947233.814576][773656:773658] CHIP:DMG:                 },
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    #Using saved values when optional attributes are available
    - label:
          "Step 9a: Test Harness Reads MaxCoolSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0017 && TSTAT.S.A0006
      response:
          constraints:
              type: int16s
              minValue: MinCoolSetpointLimitValue
              maxValue: AbsMaxCoolSetpointLimitValue

    #Using hard coded values when optional attributes are not available
    - label:
          "Step 9a: Test Harness Reads MaxCoolSetpointLimit attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0017 && !TSTAT.S.A0006
      response:
          constraints:
              type: int16s
              minValue: 1600
              maxValue: 3200

    - label:
          "Step 9a: Test Harness Writes a value back that is different but valid
          for MaxCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.F05
      arguments:
          value: 2000

    - label:
          "Step 9a: Test Harness Reads it back again to confirm the successful
          write of MaxCoolSetpointLimit attribute"
      command: "readAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.F05
      response:
          value: 2000

    - label:
          "Step 9b: Test Harness Writes MaxCoolSetpointLimit to value below the
          AbsMinCoolSetpointLimit "
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0017
      arguments:
          value: 500
      response:
          error: CONSTRAINT_ERROR

    #AbsMinCoolSetpointLimit might be negative if not checked before decrement
    - label:
          "Step 9b: Test Harness Writes MaxCoolSetpointLimit to value below the
          AbsMinCoolSetpointLimit"
      PICS:
          TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0017 && PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          #1. Test Harness Client attempts to write MaxCoolSetpointLimit below the MinCoolSetpointLimit and confirms that the device does not accept the value.

          ./chip-tool thermostat write max-cool-setpoint-limit 100 1 1

          On TH(chip-tool) verify that  DUT sends a CONSTRAINT_ERROR (0x87)
          [1676030395.441963][19525:19527] CHIP:DMG: }
          [1676030395.442028][19525:19527] CHIP:DMG: WriteClient moving to [AwaitingDe]
          [1676030395.442059][19525:19527] CHIP:TOO: Response Failure: IM Error 0x00000587: General error: 0x87 (CONSTRAINT_ERROR)
          [1676030395.442147][19525:19527] CHIP:EM: <<< [E:35527i M:176995637 (Ack:93643096)] (S) Msg TX to 1:0000000000000001 [E8D5] --- Type 0000:10 (SecureChannel:StandaloneAck)
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 9b: Test Harness Writes MaxCoolSetpointLimit to value above the
          MaxCoolSetpointLimit "
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0006
      arguments:
          value: 4000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 9b: Test Harness Writes MaxCoolSetpointLimit to value above the
          MaxCoolSetpointLimit "
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0006
      arguments:
          value: AbsMaxCoolSetpointLimitValue + 1000
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 9c: Test Harness Writes the limit of AbsMaxCoolSetpointLimit to
          MaxCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0006
      arguments:
          value: 3200

    - label:
          "Step 9c: Test Harness Writes the limit of AbsMaxCoolSetpointLimit to
          MaxCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0006
      arguments:
          value: AbsMaxCoolSetpointLimitValue

    - label:
          "Step 9c: Test Harness Writes the limit of MinCoolSetpointLimit to
          MaxCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0017 && !TSTAT.S.F05
      arguments:
          value: 1600

    - label:
          "Step 9c: Test Harness Writes the limit of MinCoolSetpointLimit to
          MaxCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0017 && TSTAT.S.F05
      arguments:
          value: 1600
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 9c: Test Harness Writes the limit of MinCoolSetpointLimit to
          MaxCoolSetpointLimit attribute"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0017 && !TSTAT.S.F05
      arguments:
          value: MinCoolSetpointLimitValue

    #LowerLimit = Max(MinCoolSetpointLimit,(MaxHeatSetpointLimit + MinSetpointDeadBand)) not possible in YAML
    - label:
          "Step 9c: Test Harness Writes If TSTAT.S.F05(AUTO) LowerLimit =
          Max(MinCoolSetpointLimit, (MaxHeatSetpointLimit +
          MinSetpointDeadBand)) to MaxCoolSetpointLimit attribute"
      PICS:
          TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0016 && TSTAT.S.F05 &&
          PICS_SKIP_SAMPLE_APP
      verification: |
          Optional Attribute - If it is supported, then in TH log it will results in displaying the value, else it will display UNSUPPORTED_ATTRIBUTE. Below is the log of RPI the result may be vary on the basis of dut implementation.

          Test Harness Client then attempts to write MaxCoolSetpointLimit to both of the limits of LowerLimit & AbsMaxCoolSetpointLimit and confirms that the device does accept the value.
          below is an example command

          ./chip-tool thermostat write max-cool-setpoint-limit 2000 1 1

          On TH verify that  DUT sends a success response

          [1678947558.840324][773890:773892] CHIP:DMG:
          [1678947558.840331][773890:773892] CHIP:DMG:                         StatusIB =
          [1678947558.840339][773890:773892] CHIP:DMG:                         {
          [1678947558.840347][773890:773892] CHIP:DMG:                                 status = 0x00 (SUCCESS),
          [1678947558.840354][773890:773892] CHIP:DMG:                         },
          [1678947558.840362][773890:773892] CHIP:DMG:
          [1678947558.840369][773890:773892] CHIP:DMG:                 },
      cluster: "LogCommands"
      command: "UserPrompt"
      arguments:
          values:
              - name: "message"
                value: "Please enter 'y' after success"
              - name: "expectedValue"
                value: "y"

    - label:
          "Step 10a: Test Harness Writes (sets back) default value of
          MinHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && TSTAT.S.A0003
      arguments:
          value: AbsMinHeatSetpointLimitValue

    - label:
          "Step 10a: Test Harness Writes (sets back) default value of
          MinHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "MinHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && !TSTAT.S.A0003
      arguments:
          value: 700

    - label:
          "Step 10a: Test Harness Writes (sets back)default value of
          MaxHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && !TSTAT.S.F05 && TSTAT.S.A0004
      arguments:
          value: AbsMaxHeatSetpointLimitValue

    - label:
          "Step 10a: Test Harness Writes (sets back)default value of
          MaxHeatSetpointLimit"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && !TSTAT.S.F05 && !TSTAT.S.A0004
      arguments:
          value: 3000

    - label:
          "Step 10a: Test Harness Writes MaxHeatSetpointLimit That meets the
          deadband of 2.5C"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0016 && TSTAT.S.F05
      arguments:
          value: 2950

    - label:
          "Step 10b: Test Harness Writes (sets back) default value of
          MinCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && TSTAT.S.A0005
      arguments:
          value: AbsMinCoolSetpointLimitValue

    - label:
          "Step 10b: Test Harness Writes (sets back) default value of
          MinCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "MinCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0017 && !TSTAT.S.A0005
      arguments:
          value: 1600

    - label:
          "Step 10b: Test Harness Writes (sets back) default value of
          MaxCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && TSTAT.S.A0006
      arguments:
          value: AbsMaxCoolSetpointLimitValue

    - label:
          "Step 10b: Test Harness Writes (sets back) default value of
          MaxCoolSetpointLimit"
      command: "writeAttribute"
      attribute: "MaxCoolSetpointLimit"
      PICS: TSTAT.S.F01 && TSTAT.S.A0018 && !TSTAT.S.A0006
      arguments:
          value: 3200

    - label:
          "Step 11a: Test Harness Reads MinSetpointDeadBand attribute from
          Server DUT and verifies that the value is within range"
      command: "readAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05
      response:
          constraints:
              type: int8s
              minValue: 0
              maxValue: 25

    - label:
          "Step 11a: Test Harness Writes a value back that is different but
          valid for MinSetpointDeadBand attribute"
      command: "writeAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05 && TSTAT.S.M.MinSetpointDeadBandWritable
      arguments:
          value: 5

    - label:
          "Step 11a: Test Harness Reads it back again to confirm the successful
          write of MinSetpointDeadBand attribute"
      command: "readAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05 && TSTAT.S.M.MinSetpointDeadBandWritable
      response:
          value: 5

    - label: "Step 11b: Test Harness Writes the value below MinSetpointDeadBand"
      command: "writeAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05 && TSTAT.S.M.MinSetpointDeadBandWritable
      arguments:
          value: -1
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 11b: Test Harness Writes the value above MinSetpointDeadBand "
      command: "writeAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05 && TSTAT.S.M.MinSetpointDeadBandWritable
      arguments:
          value: 30
      response:
          error: CONSTRAINT_ERROR

    - label:
          "Step 11c: Test Harness Writes the min limit of MinSetpointDeadBand"
      command: "writeAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05 && TSTAT.S.M.MinSetpointDeadBandWritable
      arguments:
          value: 0

    - label:
          "Step 11c: Test Harness Writes the max limit of MinSetpointDeadBand"
      command: "writeAttribute"
      attribute: "MinSetpointDeadBand"
      PICS: TSTAT.S.F05 && TSTAT.S.M.MinSetpointDeadBandWritable
      arguments:
          value: 25

    - label:
          "Step 12: Test Harness Reads ControlSequenceOfOperation from Server
          DUT, if TSTAT.S.F01 is true"
      command: "readAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F01 && !TSTAT.S.F00
      response:
          constraints:
              anyOf: [0, 1]

    - label:
          "Step 12: Test Harness Reads ControlSequenceOfOperation from Server
          DUT, if TSTAT.S.F00 is true"
      command: "readAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F00 && !TSTAT.S.F01
      response:
          constraints:
              anyOf: [2, 3]

    - label:
          "Step 12: Test Harness Reads ControlSequenceOfOperation from Server
          DUT, if both TSTAT.S.F01 and TSTAT.S.F01 are true"
      command: "readAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F00 && TSTAT.S.F01
      response:
          constraints:
              anyOf: [4, 5]

    - label:
          "Step 12: Test Harness  writes value 1 for attribute
          ControlSequenceOfOperation. If TSTAT.S.F01 is true & TSTAT.S.F00 is
          false"
      command: "writeAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F01 && !TSTAT.S.F00
      arguments:
          value: 1

    - label:
          "Step 12: Test Harness Read it back again to confirm the successful
          write"
      command: "readAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F01 && !TSTAT.S.F00
      response:
          value: 1

    - label:
          "Step 12: Test Harness writes value 3 for attribute
          ControlSequenceOfOperation. If TSTAT.S.F00 is true & TSTAT.S.F01 is
          false"
      command: "writeAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F00 && !TSTAT.S.F01
      arguments:
          value: 3

    - label:
          "Step 12: Test Harness Read it back again to confirm the successful
          write"
      command: "readAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F00 && !TSTAT.S.F01
      response:
          value: 3

    - label:
          "Step 12: Test Harness writes value 4 for attribute
          ControlSequenceOfOperation. If TSTAT.S.F01 & TSTAT.S.F00 are true"
      command: "writeAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F00 && TSTAT.S.F01
      arguments:
          value: 4

    - label:
          "Step 12: Test Harness Read it back again to confirm the successful
          write"
      command: "readAttribute"
      attribute: "ControlSequenceOfOperation"
      PICS: TSTAT.S.F00 && TSTAT.S.F01
      response:
          value: 4

    - label:
          "Test Harness Writes MaxHeatSetpointLimit attribute to default value
          of 2950 to meet deadband constraint"
      command: "writeAttribute"
      attribute: "MaxHeatSetpointLimit"
      PICS: TSTAT.S.F00 && TSTAT.S.A0015 && TSTAT.S.F05
      arguments:
          value: 2950

    - label: "Step 13: Sets OccupiedCoolingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      arguments:
          value: 2600

    - label: "Step 13: Sets OccupiedHeatingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      arguments:
          value: 2000

    - label: "Step 13: Sends SetpointRaise Command Heat Only"
      PICS: TSTAT.S.F00
      command: "SetpointRaiseLower"
      arguments:
          values:
              - name: "Mode"
                value: 0
              - name: "Amount"
                value: -30

    - label:
          "Step 13: Test Harness Reads back OccupiedHeatingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      response:
          value: 1700

    - label: "Step 14: Sets OccupiedHeatingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      arguments:
          value: 2000

    - label: "Step 14: Test Harness Sends SetpointRaise Command Heat Only"
      PICS: TSTAT.S.F00
      command: "SetpointRaiseLower"
      arguments:
          values:
              - name: "Mode"
                value: 0
              - name: "Amount"
                value: 30

    - label:
          "Step 14: Test Harness Reads back OccupiedHeatingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      response:
          value: 2300

    - label: "Step 15: Test Harness Sends SetpointRaise Command Cool Only"
      PICS: TSTAT.S.F01
      command: "SetpointRaiseLower"
      arguments:
          values:
              - name: "Mode"
                value: 1
              - name: "Amount"
                value: -30

    - label:
          "Step 15: Test Harness Reads back OccupiedCoolingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      response:
          value: 2300

    - label: "Step 16: Sets OccupiedCoolingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      arguments:
          value: 2600

    - label: "Step 16: Test Harness Sends SetpointRaise Command Cool Only"
      PICS: TSTAT.S.F01
      command: "SetpointRaiseLower"
      arguments:
          values:
              - name: "Mode"
                value: 1
              - name: "Amount"
                value: 30

    - label:
          "Step 16: Test Harness Reads back OccupiedCoolingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      response:
          value: 2900

    - label: "Step 17: Sets OccupiedCoolingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      arguments:
          value: 2600

    - label: "Step 17: Sets OccupiedHeatingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      arguments:
          value: 2000

    - label: "Step 17: Test Harness Sends SetpointRaise Command Heat & Cool"
      PICS: TSTAT.S.F00 || TSTAT.S.F01
      command: "SetpointRaiseLower"
      arguments:
          values:
              - name: "Mode"
                value: 2
              - name: "Amount"
                value: -30

    - label:
          "Step 17: Test Harness Reads back OccupiedCoolingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      response:
          value: 2300

    - label:
          "Step 17: Test Harness Reads back OccupiedHeatingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      response:
          value: 1700

    - label: "Step 18: Sets OccupiedCoolingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      arguments:
          value: 2600

    - label: "Step 18: Sets OccupiedHeatingSetpoint to default value"
      command: "writeAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      arguments:
          value: 2000

    - label: "Step 18: Test Harness Sends SetpointRaise Command Heat & Cool"
      PICS: TSTAT.S.F00 || TSTAT.S.F01
      command: "SetpointRaiseLower"
      arguments:
          values:
              - name: "Mode"
                value: 2
              - name: "Amount"
                value: 30

    - label:
          "Step 18: Test Harness Reads back OccupiedCoolingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedCoolingSetpoint"
      PICS: TSTAT.S.F01
      response:
          value: 2900

    - label:
          "Step 18: Test Harness Reads back OccupiedHeatingSetpoint to confirm
          the success of the write"
      command: "readAttribute"
      attribute: "OccupiedHeatingSetpoint"
      PICS: TSTAT.S.F00
      response:
          value: 2300