# Matter Telink Bridge Example Application

The Telink Bridge Example demonstrates a simple lighting bridge and the use of
dynamic endpoints. It uses buttons to test changing the lighting and device
states and LEDs to show the state of these changes. You can use this example as
a reference for creating your own application.

Bridge together with its Bridged Devices is exposed as a single Node with a list
of endpoints. Consequently, a single Node ID and a single Operational
Certificate is assigned during Commissioning and a single pass through the
commissioning flow is required to bring the Bridge (along with its Bridged
Devices) onto a Fabric. This provides for a simple user experience, since the
user only needs to go through the commissioning flow for the Bridge, and not
separately for each of the Bridged Devices.

![Telink B91 EVK](http://wiki.telink-semi.cn/wiki/assets/Hardware/B91_Generic_Starter_Kit_Hardware_Guide/connection_chart.png)

## Introduction

A prototype application that demonstrates dynamic endpoint with device
commissioning and cluster control. It adds the non-chip device as endpoints on a
bridge(Matter device). In this example four light devices supporting on-off
cluster and temperature sensor have been added as endpoints

1. Light1 at endpoint 3
2. Light2 at endpoint 7
3. Light3 at endpoint 5
4. Light4 at endpoint 6
5. Temperature Sensor at endpoint 8

## Dynamic Endpoints

The Bridge Example makes use of Dynamic Endpoints. Current SDK support is
limited for dynamic endpoints, since endpoints are typically defined (along with
the clusters and attributes they contain) in a .zap file which then generates
code and static structures to define the endpoints.

To support endpoints that are not statically defined, the ZCL attribute storage
mechanisms will hold additional endpoint information for `NUM_DYNAMIC_ENDPOINTS`
additional endpoints. These additional endpoint structures must be defined by
the application and can change at runtime.

To facilitate the creation of these endpoint structures, several macros are
defined:

`DECLARE_DYNAMIC_ATTRIBUTE_LIST_BEGIN(attrListName)`
`DECLARE_DYNAMIC_ATTRIBUTE(attId, attType, attSizeBytes, attrMask)`
`DECLARE_DYNAMIC_ATTRIBUTE_LIST_END(clusterRevision)`

-   These three macros are used to declare a list of attributes for use within a
    cluster. The declaration must begin with the
    `DECLARE_DYNAMIC_ATTRIBUTE_LIST_BEGIN` macro which will define the name of
    the allocated attribute structure. Each attribute is then added by the
    `DECLARE_DYNAMIC_ATTRIBUTE` macro. Finally,
    `DECLARE_DYNAMIC_ATTRIBUTE_LIST_END` macro should be used to close the
    definition.

-   All attributes defined with these macros will be configured as
    `ATTRIBUTE_MASK_EXTERNAL_STORAGE` in the ZCL database and therefore will
    rely on the application to maintain storage for the attribute. Consequently,
    reads or writes to these attributes must be handled within the application
    by the `emberAfExternalAttributeWriteCallback` and
    `emberAfExternalAttributeReadCallback` functions. See the bridge
    application's `main.cpp` for an example of this implementation.

`DECLARE_DYNAMIC_CLUSTER_LIST_BEGIN(clusterListName)`
`DECLARE_DYNAMIC_CLUSTER(clusterId, clusterAttrs, role, incomingCommands, outgoingCommands)`
`DECLARE_DYNAMIC_CLUSTER_LIST_END`

-   These three macros are used to declare a list of clusters for use within a
    endpoint. The declaration must begin with the
    `DECLARE_DYNAMIC_CLUSTER_LIST_BEGIN` macro which will define the name of the
    allocated cluster structure. Each cluster is then added by the
    `DECLARE_DYNAMIC_CLUSTER` macro referencing attribute list previously
    defined by the `DECLARE_DYNAMIC_ATTRIBUTE...` macros and the lists of
    incoming/outgoing commands terminated by kInvalidCommandId (or nullptr if
    there aren't any commands in the list). Finally,
    `DECLARE_DYNAMIC_CLUSTER_LIST_END` macro should be used to close the
    definition.

`DECLARE_DYNAMIC_ENDPOINT(endpointName, clusterList)`

-   This macro is used to declare an endpoint and its associated cluster list,
    which must be previously defined by the `DECLARE_DYNAMIC_CLUSTER...` macros.

## Supported devices

The example supports building and running on the following devices:

| Board/SoC                                                                                                                                                              | Build target                                                  | Zephyr Board Info                                                                                              |
| ---------------------------------------------------------------------------------------------------------------------------------------------------------------------- | ------------------------------------------------------------- | -------------------------------------------------------------------------------------------------------------- |
| [B91](https://wiki.telink-semi.cn/wiki/Hardware/B91_Generic_Starter_Kit_Hardware_Guide) [TLSR9518ADK80D](https://wiki.telink-semi.cn/wiki/chip-series/TLSR951x-Series) | `tlsr9518adk80d`, `tlsr9518adk80d-mars`, `tlsr9518adk80d-usb` | [TLSR9518ADK80D](https://github.com/telink-semi/zephyr/blob/develop/boards/riscv/tlsr9518adk80d/doc/index.rst) |
| [B92](https://wiki.telink-semi.cn/wiki/Hardware/B92_Generic_Starter_Kit_Hardware_Guide) [TLSR9528A](https://wiki.telink-semi.cn/wiki/chip-series/TLSR952x-Series)      | `tlsr9528a`, `tlsr9528a_retention`                            | [TLSR9528A](https://github.com/telink-semi/zephyr/blob/develop/boards/riscv/tlsr9528a/doc/index.rst)           |
| [B95](https://wiki.telink-semi.cn/wiki/Hardware/B95_Generic_Starter_Kit_Hardware_Guide) [TLSR9258A](https://wiki.telink-semi.cn/wiki/chip-series/TLSR925x-Series)      | `tlsr9258a`                                                   | [TLSR9258A](https://github.com/telink-semi/zephyr/blob/develop/boards/riscv/tlsr9258a/doc/index.rst)           |
| [W91](https://wiki.telink-semi.cn/wiki/Hardware/W91_Generic_Starter_Kit_Hardware_Guide) [TLSR9118BDK40D](https://wiki.telink-semi.cn/wiki/chip-series/TLSR911x-Series) | `tlsr9118bdk40d`                                              | [TLSR9118BDK40D](https://github.com/telink-semi/zephyr/blob/develop/boards/riscv/tlsr9118bdk40d/doc/index.rst) |

## Build and flash

1. Run the Docker container:

    ```bash
    $ docker run -it --rm -v $PWD:/host -w /host ghcr.io/project-chip/chip-build-telink:$(wget -q -O - https://raw.githubusercontent.com/project-chip/connectedhomeip/master/.github/workflows/examples-telink.yaml 2> /dev/null | grep chip-build-telink | awk -F: '{print $NF}')
    ```

    You can find the compatible Docker image version in the file:

    ```bash
    $ .github/workflows/examples-telink.yaml
    ```

2. Activate the build environment:

    ```bash
    $ source ./scripts/activate.sh -p all,telink
    ```

3. Build the example (replace _<build_target>_ with your board name, see
   [Supported devices](#supported-devices)):

    ```bash
    $ west build -b <build_target>
    ```

    Also use key `-DFLASH_SIZE`, if your board has memory size different from 2
    MB, for example, `-DFLASH_SIZE=1m` or `-DFLASH_SIZE=4m`:

    ```bash
    $ west build -b <build_target> -- -DFLASH_SIZE=4m
    ```

    You can find the target built file called **_zephyr.bin_** under the
    **_build/zephyr_** directory.

4. Flash binary:

    ```
    $ west flash --erase
    ```

## Usage

### UART

To get output from device, connect UART to following pins:

| Name | Pin                           |
| :--: | :---------------------------- |
|  RX  | PB3 (pin 17 of J34 connector) |
|  TX  | PB2 (pin 16 of J34 connector) |
| GND  | GND                           |

Baud rate: 115200 bits/s

### Buttons

The following buttons are available on **tlsr9518adk80d** board:

| Name     | Function               | Description                                                                                                                                       |
| :------- | :--------------------- | :------------------------------------------------------------------------------------------------------------------------------------------------ |
| Button 1 | Factory reset          | Perform factory reset to forget currently commissioned Thread network and return to a decommissioned state (to activate, push the button 3 times) |
| Button 2 | Lighting control       | Manually triggers the lighting state                                                                                                              |
| Button 3 | Thread start           | Commission thread with static credentials and enables the Thread on device                                                                        |
| Button 4 | Open commission window | The button is opening commissioning window to perform commissioning over BLE                                                                      |

### LEDs

#### Indicate current state of Thread network

**Red** LED indicates current state of Thread network. It is able to be in
following states:

| State                       | Description                                                                  |
| :-------------------------- | :--------------------------------------------------------------------------- |
| Blinks with short pulses    | Device is not commissioned to Thread, Thread is disabled                     |
| Blinks with frequent pulses | Device is commissioned, Thread enabled. Device trying to JOIN thread network |
| Blinks with wide pulses     | Device commissioned and joined to thread network as CHILD                    |

#### Indicate identify of device

**Green** LED used to identify the device. The LED starts blinking when the
Identify command of the Identify cluster is received. The command's argument can
be used to specify the the effect. It is able to be in following effects:

| Effect                          | Description                                                                  |
| :------------------------------ | :--------------------------------------------------------------------------- |
| Blinks (200 ms on/200 ms off)   | Blink (`Clusters::Identify::EffectIdentifierEnum::kBlink`)                   |
| Breathe (during 1000 ms)        | Breathe (`Clusters::Identify::EffectIdentifierEnum::kBreathe`)               |
| Blinks (50 ms on/950 ms off)    | Okay (`Clusters::Identify::EffectIdentifierEnum::kOkay`)                     |
| Blinks (1000 ms on/1000 ms off) | Channel Change ( `Clusters::Identify::EffectIdentifierEnum::kChannelChange`) |
| Blinks (950 ms on/50 ms off)    | Finish ( `Clusters::Identify::EffectIdentifierEnum::kFinishEffect`)          |
| LED off                         | Stop (`Clusters::Identify::EffectIdentifierEnum::kStopEffect`)               |

### CHIP tool commands

1. Build
   [chip-tool cli](https://github.com/project-chip/connectedhomeip/blob/master/examples/chip-tool/README.md)

2. Pair with device

    ```
    ${CHIP_TOOL_DIR}/chip-tool pairing ble-thread ${NODE_ID} hex:${DATASET} ${PIN_CODE} ${DISCRIMINATOR}
    ```

    Example:

    ```
    ./chip-tool pairing ble-thread 1234 hex:0e080000000000010000000300000f35060004001fffe0020811111111222222220708fd61f77bd3df233e051000112233445566778899aabbccddeeff030e4f70656e54687265616444656d6f010212340410445f2b5ca6f2a93a55ce570a70efeecb0c0402a0fff8 20202021 3840
    ```

3. Switch on the light:

    ```
    ${CHIP_TOOL_DIR}/chip-tool onoff on 1 2
    ```

    here:

    - **onoff** is name of cluster
    - **on** command to the cluster
    - **1** ID of Node
    - **2** ID of endpoint

4. Switch off the light:

    ```
    ${CHIP_TOOL_DIR}/chip-tool onoff off 1 2
    ```

    here:

    - **onoff** is name of cluster
    - **off** command to the cluster
    - **1** ID of Node
    - **2** ID of endpoint

5. Read the light state:

    ```
    ${CHIP_TOOL_DIR}/chip-tool onoff read on-off 1 2
    ```

    here:

    - **onoff** is name of cluster
    - **read** command to the cluster
    - **on-off** attribute to read
    - **1** ID of Node
    - **2** ID of endpoint

6. Change brightness of light:

    ```
    ${CHIP_TOOL_DIR}/chip-tool levelcontrol move-to-level 32 0 0 0 1 2
    ```

    here:

    - **levelcontrol** is name of cluster
    - **move-to-level** command to the cluster
    - **32** brightness value
    - **0** transition time
    - **0** option mask
    - **0** option override
    - **1** ID of Node
    - **2** ID of endpoint

7. Read brightness level:
    ```
    ./chip-tool levelcontrol read current-level 1 2
    ```
    here:
    - **levelcontrol** is name of cluster
    - **read** command to the cluster
    - **current-level** attribute to read
    - **1** ID of Node
    - **2** ID of endpoint

### OTA with Linux OTA Provider

OTA feature enabled by default only for ota-requestor-app example. To enable OTA
feature for another Telink example:

-   set CONFIG_CHIP_OTA_REQUESTOR=y in corresponding "prj.conf" configuration
    file.

After build application with enabled OTA feature, use next binary files:

-   zephyr.bin - main binary to flash PCB (Use at least 2MB PCB).
-   zephyr-ota.bin - binary for OTA Provider

All binaries has the same SW version. To test OTA “zephyr-ota.bin” should have
higher SW version than base SW. Set CONFIG_CHIP_DEVICE_SOFTWARE_VERSION=2 in
corresponding “prj.conf” conﬁguration file.

Usage of OTA:

-   Build the [Linux OTA Provider](../../ota-provider-app/linux)

    ```
    ./scripts/examples/gn_build_example.sh examples/ota-provider-app/linux out/ota-provider-app chip_config_network_layer_ble=false
    ```

-   Run the Linux OTA Provider with OTA image.

    ```
    ./chip-ota-provider-app -f zephyr-ota.bin
    ```

-   Provision the Linux OTA Provider using chip-tool

    ```
    ./chip-tool pairing onnetwork ${OTA_PROVIDER_NODE_ID} 20202021
    ```

    here:

    -   \${OTA_PROVIDER_NODE_ID} is the node id of Linux OTA Provider

-   Configure the ACL of the ota-provider-app to allow access

    ```
    ./chip-tool accesscontrol write acl '[{"fabricIndex": 1, "privilege": 5, "authMode": 2, "subjects": [112233], "targets": null}, {"fabricIndex": 1, "privilege": 3, "authMode": 2, "subjects": null, "targets": null}]' ${OTA_PROVIDER_NODE_ID} 0
    ```

    here:

    -   \${OTA_PROVIDER_NODE_ID} is the node id of Linux OTA Provider

-   Use the chip-tool to announce the ota-provider-app to start the OTA process

    ```
    ./chip-tool otasoftwareupdaterequestor announce-otaprovider ${OTA_PROVIDER_NODE_ID} 0 0 0 ${DEVICE_NODE_ID} 0
    ```

    here:

    -   \${OTA_PROVIDER_NODE_ID} is the node id of Linux OTA Provider
    -   \${DEVICE_NODE_ID} is the node id of paired device

Once the transfer is complete, OTA requestor sends ApplyUpdateRequest command to
OTA provider for applying the image. Device will restart on successful
application of OTA image.