| // ---------------------------------------------------------------------------- |
| // Second stage boot code |
| // Copyright (c) 2019-2021 Raspberry Pi (Trading) Ltd. |
| // SPDX-License-Identifier: BSD-3-Clause |
| // |
| // Device: Winbond W25X10CL |
| // |
| // Description: Configures W25X10CL to run in Dual I/O continuous read XIP mode |
| // |
| // Details: * Disable SSI |
| // * Configure SSI to generate 8b command + 28b address + 2 wait, |
| // with address and data using dual SPI mode |
| // * Enable SSI |
| // * Generate dummy read with command = 0xBB, top 24b of address |
| // of 0x000000 followed by M[7:0]=0010zzzz (with the HiZ being |
| // generated by 2 wait cycles). This leaves the W25X10CL in |
| // continuous read mode |
| // * Disable SSI |
| // * Configure SSI to generate 0b command + 28b address + 2 wait, |
| // with the extra 4 bits of address LSB being 0x2 to keep the |
| // W25X10CL in continuous read mode forever |
| // * Enable SSI |
| // * Set VTOR = 0x10000100 |
| // * Read MSP reset vector from 0x10000100 and write to MSP (this |
| // will also enable XIP mode in the SSI wrapper) |
| // * Read PC reset vector from 0x10000104 and jump to it |
| // |
| // Building: * This code must be linked to run at 0x20000000 |
| // * The code will be padded to a size of 256 bytes, including a |
| // 4-byte checksum. Therefore code size cannot exceed 252 bytes. |
| // ---------------------------------------------------------------------------- |
| |
| #include "pico/asm_helper.S" |
| #include "hardware/regs/addressmap.h" |
| #include "hardware/regs/ssi.h" |
| |
| // The serial flash interface will run at clk_sys/PICO_FLASH_SPI_CLKDIV. |
| // This must be an even number. |
| #ifndef PICO_FLASH_SPI_CLKDIV |
| #define PICO_FLASH_SPI_CLKDIV 4 |
| #endif |
| |
| pico_default_asm_setup |
| |
| // ---------------------------------------------------------------------------- |
| // The "System Control Block" is a set of internal Cortex-M0+ control registers |
| // that are memory mapped and accessed like any other H/W register. They have |
| // fixed addresses in the address map of every Cortex-M0+ system. |
| // ---------------------------------------------------------------------------- |
| |
| .equ SCB_VTOR, 0xE000ED08 // RW Vector Table Offset Register |
| |
| // ---------------------------------------------------------------------------- |
| // Winbond W25X10CL Supported Commands |
| // Taken from "w25x10cl_reg_021714.pdf" |
| // ---------------------------------------------------------------------------- |
| |
| .equ W25X10CL_CMD_READ_DATA_FAST_DUAL_IO, 0xbb |
| |
| // ---------------------------------------------------------------------------- |
| // Winbond W25X10CL "Mode bits" are 8 special bits sent immediately after |
| // the address bits in a "Read Data Fast Dual I/O" command sequence. |
| // Of M[7:4], they say M[7:6] are reserved (set to zero), and bits M[3:0] |
| // are don't care (we HiZ). Only M[5:4] are used, and they must be set |
| // to M[5:4] = 2'b10 to enable continuous read mode. |
| // ---------------------------------------------------------------------------- |
| |
| .equ W25X10CL_MODE_CONTINUOUS_READ, 0x20 |
| |
| // ---------------------------------------------------------------------------- |
| // Start of 2nd Stage Boot Code |
| // ---------------------------------------------------------------------------- |
| |
| .org 0 |
| |
| .section .text |
| |
| // This code will get copied to 0x20000000 and then executed |
| |
| regular_func _stage2_boot |
| push {lr} |
| ldr r3, =XIP_SSI_BASE // Use as base address where possible |
| |
| // We are primarily interested in setting up Flash for DSPI XIP w/ continuous read |
| |
| movs r1, #0 |
| str r1, [r3, #SSI_SSIENR_OFFSET] // Disable SSI to allow further config |
| |
| // The Boot ROM sets a very conservative SPI clock frequency to be sure it can |
| // read the initial 256 bytes from any device. Here we can be more aggressive. |
| |
| movs r1, #PICO_FLASH_SPI_CLKDIV |
| str r1, [r3, #SSI_BAUDR_OFFSET] // Set SSI Clock |
| |
| // First we need to send the initial command to get us in to Fast Read Dual I/O |
| // mode. As this transaction requires a command, we can't send it in XIP mode. |
| // To enter Continuous Read mode as well we need to append 4'b0010 to the address |
| // bits and then add a further 4 don't care bits. We will construct this by |
| // specifying a 28-bit address, with the least significant bits being 4'b0010. |
| // This is just a dummy transaction so we'll perform a read from address zero |
| // and then discard what comes back. All we really care about is that at the |
| // end of the transaction, the Winbond W25X10CL device is in Continuous Read mode |
| // and from then on will only expect to receive addresses. |
| |
| #define CTRLR0_ENTER_XIP \ |
| (SSI_CTRLR0_SPI_FRF_VALUE_DUAL /* Dual I/O mode */ \ |
| << SSI_CTRLR0_SPI_FRF_LSB) | \ |
| (31 << SSI_CTRLR0_DFS_32_LSB) | /* 32 data bits */ \ |
| (SSI_CTRLR0_TMOD_VALUE_EEPROM_READ /* Send INST/ADDR, Receive Data */ \ |
| << SSI_CTRLR0_TMOD_LSB) |
| |
| ldr r1, =(CTRLR0_ENTER_XIP) |
| str r1, [r3, #SSI_CTRLR0_OFFSET] |
| |
| movs r1, #0x0 // NDF=0 (single 32b read) |
| str r1, [r3, #SSI_CTRLR1_OFFSET] |
| |
| #define SPI_CTRLR0_ENTER_XIP \ |
| (7 << SSI_SPI_CTRLR0_ADDR_L_LSB) | /* Send 28 bits (24 address + 4 mode) */ \ |
| (2 << SSI_SPI_CTRLR0_WAIT_CYCLES_LSB) | /* Hi-Z the other 4 mode bits (2 cycles @ dual I/O = 4 bits) */ \ |
| (SSI_SPI_CTRLR0_INST_L_VALUE_8B \ |
| << SSI_SPI_CTRLR0_INST_L_LSB) | /* 8-bit instruction */ \ |
| (SSI_SPI_CTRLR0_TRANS_TYPE_VALUE_1C2A /* Send Command in serial mode then address in Dual I/O mode */ \ |
| << SSI_SPI_CTRLR0_TRANS_TYPE_LSB) |
| |
| ldr r1, =(SPI_CTRLR0_ENTER_XIP) |
| ldr r0, =(XIP_SSI_BASE + SSI_SPI_CTRLR0_OFFSET) // SPI_CTRL0 Register |
| str r1, [r0] |
| |
| movs r1, #1 // Re-enable SSI |
| str r1, [r3, #SSI_SSIENR_OFFSET] |
| |
| movs r1, #W25X10CL_CMD_READ_DATA_FAST_DUAL_IO // 8b command = 0xBB |
| str r1, [r3, #SSI_DR0_OFFSET] // Push SPI command into TX FIFO |
| movs r1, #0x0000002 // 28-bit Address for dummy read = 0x000000 + 0x2 Mode bits to set M[5:4]=10 |
| str r1, [r3, #SSI_DR0_OFFSET] // Push Address into TX FIFO - this will trigger the transaction |
| |
| // Now we wait for the read transaction to complete by monitoring the SSI |
| // status register and checking for the "RX FIFO Not Empty" flag to assert. |
| |
| movs r1, #SSI_SR_RFNE_BITS |
| 00: |
| ldr r0, [r3, #SSI_SR_OFFSET] // Read status register |
| tst r0, r1 // RFNE status flag set? |
| beq 00b // If not then wait |
| |
| // At this point CN# will be deasserted and the SPI clock will not be running. |
| // The Winbond WX25X10CL device will be in continuous read, dual I/O mode and |
| // only expecting address bits after the next CN# assertion. So long as we |
| // send 4'b0010 (and 4 more dummy HiZ bits) after every subsequent 24b address |
| // then the Winbond device will remain in continuous read mode. This is the |
| // ideal mode for Execute-In-Place. |
| // (If we want to exit continuous read mode then we will need to switch back |
| // to APM mode and generate a 28-bit address phase with the extra nibble set |
| // to 4'b0000). |
| |
| movs r1, #0 |
| str r1, [r3, #SSI_SSIENR_OFFSET] // Disable SSI (and clear FIFO) to allow further config |
| |
| // Note that the INST_L field is used to select what XIP data gets pushed into |
| // the TX FIFO: |
| // INST_L_0_BITS {ADDR[23:0],XIP_CMD[7:0]} Load "mode bits" into XIP_CMD |
| // Anything else {XIP_CMD[7:0],ADDR[23:0]} Load SPI command into XIP_CMD |
| |
| #define SPI_CTRLR0_XIP \ |
| (W25X10CL_MODE_CONTINUOUS_READ /* Mode bits to keep Winbond in continuous read mode */ \ |
| << SSI_SPI_CTRLR0_XIP_CMD_LSB) | \ |
| (7 << SSI_SPI_CTRLR0_ADDR_L_LSB) | /* Send 28 bits (24 address + 4 mode) */ \ |
| (2 << SSI_SPI_CTRLR0_WAIT_CYCLES_LSB) | /* Hi-Z the other 4 mode bits (2 cycles @ dual I/O = 4 bits) */ \ |
| (SSI_SPI_CTRLR0_INST_L_VALUE_NONE /* Do not send a command, instead send XIP_CMD as mode bits after address */ \ |
| << SSI_SPI_CTRLR0_INST_L_LSB) | \ |
| (SSI_SPI_CTRLR0_TRANS_TYPE_VALUE_2C2A /* Send Address in Dual I/O mode (and Command but that is zero bits long) */ \ |
| << SSI_SPI_CTRLR0_TRANS_TYPE_LSB) |
| |
| ldr r1, =(SPI_CTRLR0_XIP) |
| ldr r0, =(XIP_SSI_BASE + SSI_SPI_CTRLR0_OFFSET) |
| str r1, [r0] |
| |
| movs r1, #1 |
| str r1, [r3, #SSI_SSIENR_OFFSET] // Re-enable SSI |
| |
| // We are now in XIP mode, with all transactions using Dual I/O and only |
| // needing to send 24-bit addresses (plus mode bits) for each read transaction. |
| |
| // Pull in standard exit routine |
| #include "boot2_helpers/exit_from_boot2.S" |
| |
| .global literals |
| literals: |
| .ltorg |
| |
| .end |