.. _imx8mp_evk:

NXP i.MX8MP EVK
###############

Overview
********

i.MX8M Plus LPDDR4 EVK board is based on NXP i.MX8M Plus applications
processor, composed of a quad Cortex®-A53 cluster and a single Cortex®-M7 core.
Zephyr OS is ported to run on the Cortex®-A53 core.

- Board features:

  - RAM: 2GB LPDDR4
  - Storage:

    - SanDisk 16GB eMMC5.1
    - Micron 32MB QSPI NOR
    - microSD Socket
  - Wireless:

    - WiFi: 2.4/5GHz IEEE 802.11b/g/n
    - Bluetooth: v4.1
  - USB:

    - OTG - 2x type C
  - Ethernet
  - PCI-E M.2
  - Connectors:

    - 40-Pin Dual Row Header
  - LEDs:

    - 1x Power status LED
    - 1x UART LED
  - Debug

    - JTAG 20-pin connector
    - MicroUSB for UART debug, two COM ports for A53 and M4

More information about the board can be found at the
`NXP website`_.

Supported Features
==================

The Zephyr mimx8mp_evk_a53 board configuration supports the following hardware
features:

+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component                    |
+===========+============+=====================================+
| GIC-v3    | on-chip    | interrupt controller                |
+-----------+------------+-------------------------------------+
| ARM TIMER | on-chip    | system clock                        |
+-----------+------------+-------------------------------------+
| UART      | on-chip    | serial port                         |
+-----------+------------+-------------------------------------+

The Zephyr mimx8mp_evk_m7 board configuration supports the following hardware
features:

+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component                    |
+===========+============+=====================================+
| NVIC      | on-chip    | nested vector interrupt controller  |
+-----------+------------+-------------------------------------+
| SYSTICK   | on-chip    | systick                             |
+-----------+------------+-------------------------------------+
| CLOCK     | on-chip    | clock_control                       |
+-----------+------------+-------------------------------------+
| PINMUX    | on-chip    | pinmux                              |
+-----------+------------+-------------------------------------+
| UART      | on-chip    | serial port-polling;                |
|           |            | serial port-interrupt               |
+-----------+------------+-------------------------------------+

Devices
========
System Clock
------------

This board configuration uses a system clock frequency of 8 MHz.

The M7 Core is configured to run at a 800 MHz clock speed.

Serial Port
-----------

This board configuration uses a single serial communication channel with the
CPU's UART4.

Programming and Debugging (A53)
*******************************

Copy the compiled ``zephyr.bin`` to the first FAT partition of the SD card and
plug the SD card into the board. Power it up and stop the u-boot execution at
prompt.

Use U-Boot to load and kick non-smp zephyr.bin:

.. code-block:: console

    mw 303d0518 f 1; fatload mmc 1:1 0xc0000000 zephyr.bin; dcache flush; icache flush; dcache off; icache off; go 0xc0000000

Or kick SMP zephyr.bin:

.. code-block:: console

    mw 303d0518 f 1; fatload mmc 1:1 0xc0000000 zephyr.bin; dcache flush; icache flush; dcache off; icache off; cpu 2 release 0xc0000000

Use this configuration to run basic Zephyr applications and kernel tests,
for example, with the :zephyr:code-sample:`synchronization` sample:

.. zephyr-app-commands::
   :zephyr-app: samples/synchronization
   :host-os: unix
   :board: imx8mp_evk/mimx8ml8/a53
   :goals: run

This will build an image with the synchronization sample app, boot it and
display the following console output:

.. code-block:: console

    *** Booting Zephyr OS build zephyr-v3.1.0-3575-g44dd713bd883  ***
    thread_a: Hello World from cpu 0 on mimx8mp_evk_a53!
    thread_b: Hello World from cpu 0 on mimx8mp_evk_a53!
    thread_a: Hello World from cpu 0 on mimx8mp_evk_a53!
    thread_b: Hello World from cpu 0 on mimx8mp_evk_a53!
    thread_a: Hello World from cpu 0 on mimx8mp_evk_a53!

Use Jailhouse hypervisor, after root cell linux is up:

.. code-block:: console

    #jailhouse enable imx8mp.cell
    #jailhouse cell create imx8mp-zephyr.cell
    #jailhouse cell load 1 zephyr.bin -a 0xc0000000
    #jailhouse cell start 1

Programming and Debugging (M7)
******************************

The MIMX8MP EVK board doesn't have QSPI flash for the M7, and it needs
to be started by the A53 core. The A53 core is responsible to load the M7 binary
application into the RAM, put the M7 in reset, set the M7 Program Counter and
Stack Pointer, and get the M7 out of reset. The A53 can perform these steps at
bootloader level or after the Linux system has booted.

The M7 can use up to 3 different RAMs (currently, only two configurations are
supported: ITCM and DDR). These are the memory mapping for A53 and M7:

+------------+-------------------------+------------------------+-----------------------+----------------------+
| Region     | Cortex-A53              | Cortex-M7 (System Bus) | Cortex-M7 (Code Bus)  | Size                 |
+============+=========================+========================+=======================+======================+
| OCRAM      | 0x00900000-0x0098FFFF   | 0x20200000-0x2028FFFF  | 0x00900000-0x0098FFFF | 576KB                |
+------------+-------------------------+------------------------+-----------------------+----------------------+
| DTCM       | 0x00800000-0x0081FFFF   | 0x20000000-0x2001FFFF  |                       | 128KB                |
+------------+-------------------------+------------------------+-----------------------+----------------------+
| ITCM       | 0x007E0000-0x007FFFFF   |                        | 0x00000000-0x0001FFFF | 128KB                |
+------------+-------------------------+------------------------+-----------------------+----------------------+
| OCRAM_S    | 0x00180000-0x00188FFF   | 0x20180000-0x20188FFF  | 0x00180000-0x00188FFF | 36KB                 |
+------------+-------------------------+------------------------+-----------------------+----------------------+
| DDR        | 0x80000000-0x803FFFFF   | 0x80200000-0x803FFFFF  | 0x80000000-0x801FFFFF | 2MB                  |
+------------+-------------------------+------------------------+-----------------------+----------------------+

For more information about memory mapping see the
`i.MX 8M Applications Processor Reference Manual`_  (section 2.1 to 2.3)

At compilation time you have to choose which RAM will be used. This
configuration is done based on board name (imx8mp_evk/mimx8ml8/m7 for ITCM and
imx8mp_evk/mimx8ml8/m7/ddr for DDR).

Load and run Zephyr on M7 from A53 using u-boot by copying the compiled
``zephyr.bin`` to the first FAT partition of the SD card and plug the SD
card into the board. Power it up and stop the u-boot execution at prompt.

Load the M7 binary onto the desired memory and start its execution using:

ITCM
===

.. code-block:: console

   fatload mmc 0:1 0x48000000 zephyr.bin
   cp.b 0x48000000 0x7e0000 20000
   bootaux 0x7e0000

DDR
===

.. code-block:: console

   fatload mmc 0:1 0x80000000 zephyr.bin
   dcache flush
   bootaux 0x80000000

Debugging
=========

MIMX8MP EVK board can be debugged by connecting an external JLink
JTAG debugger to the J24 debug connector and to the PC. Then
the application can be debugged using the usual way.

Here is an example for the :ref:`hello_world` application.

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: imx8mp_evk/mimx8ml8/m7
   :goals: debug

Open a serial terminal, step through the application in your debugger, and you
should see the following message in the terminal:

.. code-block:: console

   *** Booting Zephyr OS build v2.7.99-1310-g2801bf644a91  ***
   Hello World! imx8mp_evk

References
==========

.. _NXP website:
   https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-plus-applications-processor:8MPLUSLPD4-EVK

.. _i.MX 8M Applications Processor Reference Manual:
   https://www.nxp.com/docs/en/reference-manual/IMX8MPRM.pdf