# Copyright (c) 2021, STMicroelectronics
# SPDX-License-Identifier: Apache-2.0

description: |
    STM32 OSPI Flash controller supporting the JEDEC CFI interface

    Representation of a serial flash on a octospi bus:

        mx25lm51245: ospi-nor-flash@70000000 {
                compatible = "st,stm32-ospi-nor";
                reg = <0x70000000 DT_SIZE_M(64)>; /* 512 Mbits */
                data-mode = <OSPI_OPI_MODE>; /* access on 8 data lines */
                data-rate = <OSPI_DTR_TRANSFER>; /* access in DTR */
                ospi-max-frequency = <DT_FREQ_M(50)>;
                status = "okay";
        };

compatible: "st,stm32-ospi-nor"

include: ["flash-controller.yaml", "jedec,jesd216.yaml"]

on-bus: ospi

properties:
  reg:
    required: true
    description: Flash Memory base address and size in bytes
  ospi-max-frequency:
    type: int
    required: true
    description: Maximum clock frequency of device's OSPI interface in Hz
  reset-gpios:
    type: phandle-array
    description: RESETn pin
  spi-bus-width:
    type: int
    required: true
    description: |
     The width of (Octo)SPI bus to which flash memory is connected.

     Possible values are :
      - OSPI_SPI_MODE  <1> = SPI mode on 1 data line
      - OSPI_DUAL_MODE <2> = Dual mode on 2 data lines
      - OSPI_QUAD_MODE <4> = Quad mode on 4 data lines
      - OSPI_OPI_MODE  <8> = Octo mode on 8 data lines
    enum:
      - 1
      - 2
      - 4
      - 8
  data-rate:
    type: int
    required: true
    description: |
     The SPI data Rate is STR or DTR

     Possible values are :
      - OSPI_STR_TRANSFER <1> = Single Rate Transfer
      - OSPI_DTR_TRANSFER <2> = Dual Rate Transfer (only with OSPI_OPI_MODE)
    enum:
      - 1
      - 2
  writeoc:
    type: string
    enum:
      - "PP"            # Page program, PP (0x02) up to 256 bytes
      - "PP_1_1_2"      # Dual page program, PP 1-1-2 (0xA2)
      - "PP_1_1_4"      # Quad data line SPI, PP 1-1-4 (0x32)
      - "PP_1_4_4"      # Quad data line SPI, PP 1-4-4 (0x38)
    description: |
      The value encodes number of I/O lines used for the opcode,
      address, and data.

      There is no info about quad page program opcodes in the SFDP
      tables, hence it has been assumed that NOR flash memory
      supporting 1-4-4 mode also would support fast page programming.

      Intended for modes other than OSPI_OPI_MODE.

      If absent, then program page opcode is determined by the
      `spi-bus-width`:

      * OSPI_SPI_MODE -> PP 1-1-1 (0x02)
      * OSPI_DUAL_MODE -> PP 1-1-2 (0xA2)
      * OSPI_QUAD_MODE -> PP 1-4-4 (0x38)
  four-byte-opcodes:
    type: boolean
    description: |
      Some NOR-Flash ICs use different opcodes when operating in
      4 byte addressing mode.

      When enabled, then 3 byte opcodes will be converted to
      4 byte opcodes.

      * PP 1-1-1 (0x02) -> PP 1-1-1 4B (0x12)
      * PP 1-1-4 (0x32) -> PP 1-1-4 4B (0x34)
      * PP 1-4-4 (0x38) -> PP 1-4-4 4B (0x3E)

      * READ 1-1-1 (0x03) -> READ 1-1-1 4B (0x13)
      * READ FAST 1-1-1 (0x0B) -> READ FAST 1-1-1 4B (0x0C)
      * DREAD 1-1-2 (0x3B) -> DREAD 1-1-2 4B (0x3C)
      * 2READ 1-2-2 (0xBB) -> 2READ 1-2-2 4B (0xBC)
      * QREAD 1-1-4 (0x6B) -> QREAD 1-1-4 4B (0x6C)
      * 4READ 1-4-4 (0xEB) -> 4READ 1-4-4 4B (0xEC)