/**
  ******************************************************************************
  * @file    stm32f7xx_hal_irda.c
  * @author  MCD Application Team
  * @version V1.1.1
  * @date    01-July-2016
  * @brief   IRDA HAL module driver.
  *          This file provides firmware functions to manage the following
  *          functionalities of the IrDA SIR ENDEC block (IrDA):
  *           + Initialization and de-initialization methods
  *           + IO operation methods
  *           + Peripheral Control methods
  *
  @verbatim
  ==============================================================================
                        ##### How to use this driver #####
  ==============================================================================
  [..]
    The IRDA HAL driver can be used as follows:

    (#) Declare a IRDA_HandleTypeDef handle structure.
    (#) Initialize the IRDA low level resources by implementing the HAL_IRDA_MspInit() API:
        (##) Enable the USARTx interface clock.
        (##) IRDA pins configuration:
            (+++) Enable the clock for the IRDA GPIOs.
            (+++) Configure these IRDA pins as alternate function pull-up.
        (##) NVIC configuration if you need to use interrupt process (HAL_IRDA_Transmit_IT()
             and HAL_IRDA_Receive_IT() APIs):
            (+++) Configure the USARTx interrupt priority.
            (+++) Enable the NVIC USART IRQ handle.
        (##) DMA Configuration if you need to use DMA process (HAL_IRDA_Transmit_DMA()
             and HAL_IRDA_Receive_DMA() APIs):
            (+++) Declare a DMA handle structure for the Tx/Rx stream.
            (+++) Enable the DMAx interface clock.
            (+++) Configure the declared DMA handle structure with the required Tx/Rx parameters.
            (+++) Configure the DMA Tx/Rx Stream.
            (+++) Associate the initialized DMA handle to the IRDA DMA Tx/Rx handle.
            (+++) Configure the priority and enable the NVIC for the transfer complete interrupt on the DMA Tx/Rx Stream.

    (#) Program the Baud Rate, Word Length, Parity, IrDA Mode, Prescaler
        and Mode(Receiver/Transmitter) in the hirda Init structure.

    (#) Initialize the IRDA registers by calling the HAL_IRDA_Init() API:
        (++) This API configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
            by calling the customized HAL_IRDA_MspInit() API.
    -@@- The specific IRDA interrupts (Transmission complete interrupt,
        RXNE interrupt and Error Interrupts) will be managed using the macros
        __HAL_IRDA_ENABLE_IT() and __HAL_IRDA_DISABLE_IT() inside the transmit and receive process.

    (#) Three operation modes are available within this driver :

    *** Polling mode IO operation ***
    =================================
    [..]
      (+) Send an amount of data in blocking mode using HAL_IRDA_Transmit()
      (+) Receive an amount of data in blocking mode using HAL_IRDA_Receive()

    *** Interrupt mode IO operation ***
    ===================================
    [..]
      (+) Send an amount of data in non blocking mode using HAL_IRDA_Transmit_IT()
      (+) At transmission end of transfer HAL_IRDA_TxCpltCallback is executed and user can
           add his own code by customization of function pointer HAL_IRDA_TxCpltCallback
      (+) Receive an amount of data in non blocking mode using HAL_IRDA_Receive_IT()
      (+) At reception end of transfer HAL_IRDA_RxCpltCallback is executed and user can
           add his own code by customization of function pointer HAL_IRDA_RxCpltCallback
      (+) In case of transfer Error, HAL_IRDA_ErrorCallback() function is executed and user can
           add his own code by customization of function pointer HAL_IRDA_ErrorCallback

    *** DMA mode IO operation ***
    =============================
    [..]
      (+) Send an amount of data in non blocking mode (DMA) using HAL_IRDA_Transmit_DMA()
      (+) At transmission end of transfer HAL_IRDA_TxCpltCallback is executed and user can
           add his own code by customization of function pointer HAL_IRDA_TxCpltCallback
      (+) Receive an amount of data in non blocking mode (DMA) using HAL_IRDA_Receive_DMA()
      (+) At reception end of transfer HAL_IRDA_RxCpltCallback is executed and user can
           add his own code by customization of function pointer HAL_IRDA_RxCpltCallback
      (+) In case of transfer Error, HAL_IRDA_ErrorCallback() function is executed and user can
           add his own code by customization of function pointer HAL_IRDA_ErrorCallback

    *** IRDA HAL driver macros list ***
    ===================================
    [..]
      Below the list of most used macros in IRDA HAL driver.

     (+) __HAL_IRDA_ENABLE: Enable the IRDA peripheral
     (+) __HAL_IRDA_DISABLE: Disable the IRDA peripheral
     (+) __HAL_IRDA_GET_FLAG : Checks whether the specified IRDA flag is set or not
     (+) __HAL_IRDA_CLEAR_FLAG : Clears the specified IRDA pending flag
     (+) __HAL_IRDA_ENABLE_IT: Enables the specified IRDA interrupt
     (+) __HAL_IRDA_DISABLE_IT: Disables the specified IRDA interrupt

     (@) You can refer to the IRDA HAL driver header file for more useful macros

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32f7xx_hal.h"

/** @addtogroup STM32F7xx_HAL_Driver
  * @{
  */

/** @defgroup IRDA IRDA
  * @brief HAL IRDA module driver
  * @{
  */
#ifdef HAL_IRDA_MODULE_ENABLED

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @addtogroup IRDA_Private_Constants
  * @{
  */
#define TEACK_REACK_TIMEOUT            1000U
#define HAL_IRDA_TXDMA_TIMEOUTVALUE    22000U
#define IRDA_CR1_FIELDS  ((uint32_t)(USART_CR1_M | USART_CR1_PCE \
                                   | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE))
/**
  * @}
  */
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/** @addtogroup IRDA_Private_Functions
  * @{
  */
static void IRDA_DMATransmitCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMATransmitHalfCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMAReceiveCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMAReceiveHalfCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMAError(DMA_HandleTypeDef *hdma);
static void IRDA_DMAAbortOnError(DMA_HandleTypeDef *hdma);
static void IRDA_EndTxTransfer(IRDA_HandleTypeDef *hirda);
static void IRDA_EndRxTransfer(IRDA_HandleTypeDef *hirda);
static void IRDA_SetConfig (IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_CheckIdleState(IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_WaitOnFlagUntilTimeout(IRDA_HandleTypeDef *hirda, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout);
static HAL_StatusTypeDef IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_EndTransmit_IT(IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_Receive_IT(IRDA_HandleTypeDef *hirda);
/**
  * @}
  */
/* Exported functions --------------------------------------------------------*/
/** @defgroup IRDA_Exported_Functions IrDA Exported Functions
  * @{
  */

/** @defgroup IRDA_Exported_Functions_Group1 IrDA Initialization and de-initialization functions
  *  @brief    Initialization and Configuration functions
  *
@verbatim

===============================================================================
            ##### Initialization and Configuration functions #####
 ===============================================================================
    [..]
    This subsection provides a set of functions allowing to initialize the USARTx or the UARTy
    in IrDA mode.
      (+) For the asynchronous mode only these parameters can be configured:
        (++) BaudRate
        (++) WordLength
        (++) Parity: If the parity is enabled, then the MSB bit of the data written
             in the data register is transmitted but is changed by the parity bit.
             Depending on the frame length defined by the M bit (8-bits or 9-bits),
             please refer to Reference manual for possible IRDA frame formats.
        (++) Prescaler: A pulse of width less than two and greater than one PSC period(s) may or may
             not be rejected. The receiver set up time should be managed by software. The IrDA physical layer
             specification specifies a minimum of 10 ms delay between transmission and
             reception (IrDA is a half duplex protocol).
        (++) Mode: Receiver/transmitter modes
        (++) IrDAMode: the IrDA can operate in the Normal mode or in the Low power mode.
    [..]
    The HAL_IRDA_Init() API follows IRDA configuration procedures (details for the procedures
    are available in reference manual).

@endverbatim
  * @{
  */

/**
  * @brief  Initializes the IRDA mode according to the specified
  *         parameters in the IRDA_InitTypeDef and create the associated handle.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Init(IRDA_HandleTypeDef *hirda)
{
    /* Check the IRDA handle allocation */
    if(hirda == NULL)
    {
        return HAL_ERROR;
    }

    /* Check the USART/UART associated to the IRDA handle */
    assert_param(IS_IRDA_INSTANCE(hirda->Instance));

    if(hirda->gState == HAL_IRDA_STATE_RESET)
    {
        /* Allocate lock resource and initialize it */
        hirda->Lock = HAL_UNLOCKED;
        /* Init the low level hardware : GPIO, CLOCK, CORTEX */
        HAL_IRDA_MspInit(hirda);
    }

    hirda->gState = HAL_IRDA_STATE_BUSY;

    /* Disable the Peripheral to update the configuration registers */
    __HAL_IRDA_DISABLE(hirda);

    /* Set the IRDA Communication parameters */
    IRDA_SetConfig(hirda);

    /* In IRDA mode, the following bits must be kept cleared:
    - LINEN, STOP and CLKEN bits in the USART_CR2 register,
    - SCEN and HDSEL bits in the USART_CR3 register.*/
    CLEAR_BIT(hirda->Instance->CR3, USART_CR2_LINEN | USART_CR2_STOP | USART_CR2_CLKEN);
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_SCEN | USART_CR3_HDSEL);

    /* set the UART/USART in IRDA mode */
    SET_BIT(hirda->Instance->CR3, USART_CR3_IREN);

    /* Enable the Peripheral */
    __HAL_IRDA_ENABLE(hirda);

    /* TEACK and/or REACK to check before moving hirda->State to Ready */
    return (IRDA_CheckIdleState(hirda));
}

/**
  * @brief  DeInitializes the IRDA peripheral
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DeInit(IRDA_HandleTypeDef *hirda)
{
    /* Check the IRDA handle allocation */
    if(hirda == NULL)
    {
        return HAL_ERROR;
    }

    /* Check the parameters */
    assert_param(IS_IRDA_INSTANCE(hirda->Instance));

    hirda->gState = HAL_IRDA_STATE_BUSY;

    /* DeInit the low level hardware */
    HAL_IRDA_MspDeInit(hirda);
    /* Disable the Peripheral */
    __HAL_IRDA_DISABLE(hirda);

    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
    hirda->gState = HAL_IRDA_STATE_RESET;
    hirda->RxState = HAL_IRDA_STATE_RESET;

    /* Release Lock */
    __HAL_UNLOCK(hirda);

    return HAL_OK;
}

/**
  * @brief  IRDA MSP Init.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_MspInit(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function Should not be modified, when the callback is needed,
              the HAL_IRDA_MspInit could be implemented in the user file
     */
}

/**
  * @brief  IRDA MSP DeInit.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_MspDeInit(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function Should not be modified, when the callback is needed,
              the HAL_IRDA_MspDeInit could be implemented in the user file
     */
}

/**
  * @}
  */

/** @defgroup IRDA_Exported_Functions_Group2 IO operation functions
  *  @brief   IRDA Transmit/Receive functions
  *
@verbatim
 ===============================================================================
                      ##### IO operation functions #####
 ===============================================================================
    This subsection provides a set of functions allowing to manage the IRDA data transfers.
    [..]
    IrDA is a half duplex communication protocol. If the Transmitter is busy, any data
    on the IrDA receive line will be ignored by the IrDA decoder and if the Receiver
    is busy, data on the TX from the USART to IrDA will not be encoded by IrDA.
    While receiving data, transmission should be avoided as the data to be transmitted
    could be corrupted.

    (#) There are two modes of transfer:
       (++) Blocking mode: the communication is performed in polling mode.
            The HAL status of all data processing is returned by the same function
            after finishing transfer.
       (++) No-Blocking mode: the communication is performed using Interrupts
           or DMA, these API's return the HAL status.
           The end of the data processing will be indicated through the
           dedicated IRDA IRQ when using Interrupt mode or the DMA IRQ when
           using DMA mode.
           The HAL_IRDA_TxCpltCallback(), HAL_IRDA_RxCpltCallback() user callbacks
           will be executed respectively at the end of the Transmit or Receive process
           The HAL_IRDA_ErrorCallback() user callback will be executed when a communication error is detected

    (#) Blocking mode API's are :
        (++) HAL_IRDA_Transmit()
        (++) HAL_IRDA_Receive()

    (#) Non-Blocking mode API's with Interrupt are :
        (++) HAL_IRDA_Transmit_IT()
        (++) HAL_IRDA_Receive_IT()
        (++) HAL_IRDA_IRQHandler()
        (++) IRDA_Transmit_IT()
        (++) IRDA_Receive_IT()

    (#) Non-Blocking mode functions with DMA are :
        (++) HAL_IRDA_Transmit_DMA()
        (++) HAL_IRDA_Receive_DMA()

    (#) A set of Transfer Complete Callbacks are provided in No_Blocking mode:
        (++) HAL_IRDA_TxCpltCallback()
        (++) HAL_IRDA_RxCpltCallback()
        (++) HAL_IRDA_ErrorCallback()

@endverbatim
  * @{
  */

/**
  * @brief  Sends an amount of data in blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData: Pointer to data buffer
  * @param  Size: Amount of data to be sent
  * @param  Timeout: Specify timeout value
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Transmit(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout)
{
    uint16_t* tmp;
    uint32_t tickstart = 0U;

    /* Check that a Tx process is not already ongoing */
    if(hirda->gState == HAL_IRDA_STATE_READY)
    {
        if((pData == NULL) || (Size == 0U))
        {
            return  HAL_ERROR;
        }

        /* Process Locked */
        __HAL_LOCK(hirda);
        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
        hirda->gState = HAL_IRDA_STATE_BUSY_TX;

        /* Init tickstart for timeout managment*/
        tickstart = HAL_GetTick();

        hirda->TxXferSize = Size;
        hirda->TxXferCount = Size;
        while(hirda->TxXferCount > 0U)
        {
            hirda->TxXferCount--;

            if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
            {
                return HAL_TIMEOUT;
            }
            if ((hirda->Init.WordLength == IRDA_WORDLENGTH_9B) && (hirda->Init.Parity == IRDA_PARITY_NONE))
            {
                tmp = (uint16_t*) pData;
                hirda->Instance->TDR = (*tmp & (uint16_t)0x01FFU);
                pData +=2;
            }
            else
            {
                hirda->Instance->TDR = (*pData++ & (uint8_t)0xFFU);
            }
        }

        if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK)
        {
            return HAL_TIMEOUT;
        }

        /* At end of Tx process, restore hirda->gState to Ready */
        hirda->gState = HAL_IRDA_STATE_READY;

        /* Process Unlocked */
        __HAL_UNLOCK(hirda);

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief  Receive an amount of data in blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData: Pointer to data buffer
  * @param  Size: Amount of data to be received
  * @param  Timeout: Specify timeout value
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Receive(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout)
{
    uint16_t* tmp;
    uint16_t uhMask;
    uint32_t tickstart = 0U;

    /* Check that a Rx process is not already ongoing */
    if(hirda->RxState == HAL_IRDA_STATE_READY)
    {
        if((pData == NULL) || (Size == 0U))
        {
            return  HAL_ERROR;
        }

        /* Process Locked */
        __HAL_LOCK(hirda);
        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
        hirda->RxState = HAL_IRDA_STATE_BUSY_RX;

        /* Init tickstart for timeout managment*/
        tickstart = HAL_GetTick();

        hirda->RxXferSize = Size;
        hirda->RxXferCount = Size;

        /* Computation of the mask to apply to the RDR register
           of the UART associated to the IRDA */
        IRDA_MASK_COMPUTATION(hirda);
        uhMask = hirda->Mask;

        /* Check data remaining to be received */
        while(hirda->RxXferCount > 0U)
        {
            hirda->RxXferCount--;

            if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
            {
                return HAL_TIMEOUT;
            }
            if ((hirda->Init.WordLength == IRDA_WORDLENGTH_9B) && (hirda->Init.Parity == IRDA_PARITY_NONE))
            {
                tmp = (uint16_t*) pData ;
                *tmp = (uint16_t)(hirda->Instance->RDR & uhMask);
                pData +=2;
            }
            else
            {
                *pData++ = (uint8_t)(hirda->Instance->RDR & (uint8_t)uhMask);
            }
        }

        /* At end of Rx process, restore hirda->RxState to Ready */
        hirda->RxState = HAL_IRDA_STATE_READY;

        /* Process Unlocked */
        __HAL_UNLOCK(hirda);

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief  Send an amount of data in non blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData: Pointer to data buffer
  * @param  Size: Amount of data to be sent
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
    /* Check that a Tx process is not already ongoing */
    if(hirda->gState == HAL_IRDA_STATE_READY)
    {
        if((pData == NULL) || (Size == 0U))
        {
            return HAL_ERROR;
        }

        /* Process Locked */
        __HAL_LOCK(hirda);

        hirda->pTxBuffPtr = pData;
        hirda->TxXferSize = Size;
        hirda->TxXferCount = Size;

        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
        hirda->gState = HAL_IRDA_STATE_BUSY_TX;

        /* Process Unlocked */
        __HAL_UNLOCK(hirda);

        /* Enable the IRDA Transmit Complete Interrupt */
        SET_BIT(hirda->Instance->CR1, USART_CR1_TCIE);

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief  Receives an amount of data in non blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData: Pointer to data buffer
  * @param  Size: Amount of data to be received
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Receive_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
    /* Check that a Rx process is not already ongoing */
    if(hirda->RxState == HAL_IRDA_STATE_READY)
    {
        if((pData == NULL) || (Size == 0U))
        {
            return HAL_ERROR;
        }

        /* Process Locked */
        __HAL_LOCK(hirda);

        hirda->pRxBuffPtr = pData;
        hirda->RxXferSize = Size;
        hirda->RxXferCount = Size;

        /* Computation of the mask to apply to the RDR register
           of the UART associated to the IRDA */
        IRDA_MASK_COMPUTATION(hirda);

        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
        hirda->RxState = HAL_IRDA_STATE_BUSY_RX;

        /* Process Unlocked */
        __HAL_UNLOCK(hirda);

        /* Enable the IRDA Parity Error Interrupt */
        SET_BIT(hirda->Instance->CR1, USART_CR1_PEIE);

        /* Enable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
        SET_BIT(hirda->Instance->CR3, USART_CR3_EIE);

        /* Enable the IRDA Data Register not empty Interrupt */
        SET_BIT(hirda->Instance->CR1, USART_CR1_RXNEIE);

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief  Sends an amount of data in non blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData: Pointer to data buffer
  * @param  Size: Amount of data to be sent
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Transmit_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
    uint32_t *tmp;

    /* Check that a Tx process is not already ongoing */
    if(hirda->gState == HAL_IRDA_STATE_READY)
    {
        if((pData == NULL) || (Size == 0U))
        {
            return HAL_ERROR;
        }

        /* Process Locked */
        __HAL_LOCK(hirda);

        hirda->pTxBuffPtr = pData;
        hirda->TxXferSize = Size;
        hirda->TxXferCount = Size;

        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
        hirda->gState = HAL_IRDA_STATE_BUSY_TX;

        /* Set the IRDA DMA transfer complete callback */
        hirda->hdmatx->XferCpltCallback = IRDA_DMATransmitCplt;

        /* Set the IRDA DMA half transfer complete callback */
        hirda->hdmatx->XferHalfCpltCallback = IRDA_DMATransmitHalfCplt;

        /* Set the DMA error callback */
        hirda->hdmatx->XferErrorCallback = IRDA_DMAError;

        /* Set the DMA abort callback */
        hirda->hdmatx->XferAbortCallback = NULL;

        /* Enable the IRDA transmit DMA channel */
        tmp = (uint32_t*)&pData;
        HAL_DMA_Start_IT(hirda->hdmatx, *(uint32_t*)tmp, (uint32_t)&hirda->Instance->TDR, Size);

        /* Clear the TC flag in the SR register by writing 0 to it */
        __HAL_IRDA_CLEAR_IT(hirda, IRDA_FLAG_TC);

        /* Process Unlocked */
        __HAL_UNLOCK(hirda);

        /* Enable the DMA transfer for transmit request by setting the DMAT bit
           in the IRDA CR3 register */
        SET_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief  Receives an amount of data in non blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData: Pointer to data buffer
  * @param  Size: Amount of data to be received
  * @note   When the IRDA parity is enabled (PCE = 1) the data received contain the parity bit.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Receive_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
    uint32_t *tmp;

    /* Check that a Rx process is not already ongoing */
    if(hirda->RxState == HAL_IRDA_STATE_READY)
    {
        if((pData == NULL) || (Size == 0U))
        {
            return HAL_ERROR;
        }

        /* Process Locked */
        __HAL_LOCK(hirda);

        hirda->pRxBuffPtr = pData;
        hirda->RxXferSize = Size;

        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
        hirda->RxState = HAL_IRDA_STATE_BUSY_RX;

        /* Set the IRDA DMA transfer complete callback */
        hirda->hdmarx->XferCpltCallback = IRDA_DMAReceiveCplt;

        /* Set the IRDA DMA half transfer complete callback */
        hirda->hdmarx->XferHalfCpltCallback = IRDA_DMAReceiveHalfCplt;

        /* Set the DMA error callback */
        hirda->hdmarx->XferErrorCallback = IRDA_DMAError;

        /* Set the DMA abort callback */
        hirda->hdmarx->XferAbortCallback = NULL;

        /* Enable the DMA channel */
        tmp = (uint32_t*)&pData;
        HAL_DMA_Start_IT(hirda->hdmarx, (uint32_t)&hirda->Instance->RDR, *(uint32_t*)tmp, Size);

        /* Process Unlocked */
        __HAL_UNLOCK(hirda);

        /* Enable the IRDA Parity Error Interrupt */
        SET_BIT(hirda->Instance->CR1, USART_CR1_PEIE);

        /* Enable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
        SET_BIT(hirda->Instance->CR3, USART_CR3_EIE);

        /* Enable the DMA transfer for the receiver request by setting the DMAR bit
        in the USART CR3 register */
        SET_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief Pauses the DMA Transfer.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DMAPause(IRDA_HandleTypeDef *hirda)
{
    /* Process Locked */
    __HAL_LOCK(hirda);

    if((hirda->gState == HAL_IRDA_STATE_BUSY_TX)&&
            (HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT)))
    {
        /* Disable the UART DMA Tx request */
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);
    }
    if((hirda->RxState == HAL_IRDA_STATE_BUSY_RX)&&
            (HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR)))
    {
        /* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
        CLEAR_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

        /* Disable the UART DMA Rx request */
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);
    }

    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    return HAL_OK;
}

/**
  * @brief Resumes the DMA Transfer.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified UART module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DMAResume(IRDA_HandleTypeDef *hirda)
{
    /* Process Locked */
    __HAL_LOCK(hirda);

    if(hirda->gState == HAL_IRDA_STATE_BUSY_TX)
    {
        /* Enable the UART DMA Tx request */
        SET_BIT(hirda->Instance->CR3, USART_CR3_DMAT);
    }
    if(hirda->RxState == HAL_IRDA_STATE_BUSY_RX)
    {
        /* Clear the Overrun flag before resuming the Rx transfer*/
        __HAL_IRDA_CLEAR_IT(hirda, IRDA_CLEAR_OREF);

        /* Reenable PE and ERR (Frame error, noise error, overrun error) interrupts */
        SET_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
        SET_BIT(hirda->Instance->CR3, USART_CR3_EIE);

        /* Enable the UART DMA Rx request */
        SET_BIT(hirda->Instance->CR3, USART_CR3_DMAR);
    }

    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    return HAL_OK;
}

/**
  * @brief Stops the DMA Transfer.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified UART module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DMAStop(IRDA_HandleTypeDef *hirda)
{
    /* The Lock is not implemented on this API to allow the user application
       to call the HAL IRDA API under callbacks HAL_IRDA_TxCpltCallback() / HAL_IRDA_RxCpltCallback() /
       HAL_IRDA_TxHalfCpltCallback / HAL_IRDA_RxHalfCpltCallback:
       indeed, when HAL_DMA_Abort() API is called, the DMA TX/RX Transfer or Half Transfer complete
       interrupt is generated if the DMA transfer interruption occurs at the middle or at the end of
       the stream and the corresponding call back is executed. */

    /* Stop IRDA DMA Tx request if ongoing */
    if ((hirda->gState == HAL_IRDA_STATE_BUSY_TX) &&
            (HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT)))
    {
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

        /* Abort the IRDA DMA Tx channel */
        if(hirda->hdmatx != NULL)
        {
            HAL_DMA_Abort(hirda->hdmatx);
        }
        IRDA_EndTxTransfer(hirda);
    }

    /* Stop IRDA DMA Rx request if ongoing */
    if ((hirda->RxState == HAL_IRDA_STATE_BUSY_RX) &&
            (HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR)))
    {
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

        /* Abort the IRDA DMA Rx channel */
        if(hirda->hdmarx != NULL)
        {
            HAL_DMA_Abort(hirda->hdmarx);
        }
        IRDA_EndRxTransfer(hirda);
    }
    return HAL_OK;
}

/**
  * @brief DMA IRDA communication abort callback, when call by HAL services on Error
  *        (To be called at end of DMA Abort procedure following error occurrence).
  * @param hdma: DMA handle.
  * @retval None
  */
static void IRDA_DMAAbortOnError(DMA_HandleTypeDef *hdma)
{
    IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
    hirda->RxXferCount = 0U;
    hirda->TxXferCount = 0U;

    HAL_IRDA_ErrorCallback(hirda);
}

/**
  * @brief  This function handles IRDA interrupt request.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
void HAL_IRDA_IRQHandler(IRDA_HandleTypeDef *hirda)
{
    uint32_t isrflags, cr1its, cr3its, errorflags;

    isrflags   = READ_REG(hirda->Instance->ISR);
    cr1its     = READ_REG(hirda->Instance->CR1);
    cr3its     = READ_REG(hirda->Instance->CR3);

    /* If no error occurs */
    errorflags = (isrflags & (uint32_t)(USART_ISR_PE | USART_ISR_FE | USART_ISR_ORE | USART_ISR_NE));
    if (errorflags == RESET)
    {
        /* IRDA in mode Receiver ---------------------------------------------------*/
        if(((isrflags & USART_ISR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET))
        {
            IRDA_Receive_IT(hirda);
            /* Clear RXNE interrupt flag */
            __HAL_IRDA_SEND_REQ(hirda, IRDA_RXDATA_FLUSH_REQUEST);
        }
    }

    /* If some errors occur */
    if((errorflags != RESET) && ((cr3its & (USART_CR3_EIE | USART_CR1_PEIE)) != RESET))
    {
        /* IRDA parity error interrupt occurred -------------------------------------*/
        if(((isrflags & USART_ISR_PE) != RESET) && ((cr1its & USART_CR1_PEIE) != RESET))
        {
            __HAL_IRDA_CLEAR_IT(hirda, IRDA_CLEAR_PEF);
            hirda->ErrorCode |= HAL_IRDA_ERROR_PE;
        }

        /* IRDA frame error interrupt occurred --------------------------------------*/
        if(((isrflags & USART_ISR_FE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
        {
            __HAL_IRDA_CLEAR_IT(hirda, IRDA_CLEAR_FEF);
            hirda->ErrorCode |= HAL_IRDA_ERROR_FE;
        }

        /* IRDA noise error interrupt occurred --------------------------------------*/
        if(((isrflags & USART_ISR_NE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
        {
            __HAL_IRDA_CLEAR_IT(hirda, IRDA_CLEAR_NEF);
            hirda->ErrorCode |= HAL_IRDA_ERROR_NE;
        }

        /* IRDA Over-Run interrupt occurred -----------------------------------------*/
        if(((isrflags & USART_ISR_ORE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
        {
            __HAL_IRDA_CLEAR_IT(hirda, IRDA_CLEAR_OREF);
            hirda->ErrorCode |= HAL_IRDA_ERROR_ORE;
        }

        /* Call IRDA Error Call back function if need be --------------------------*/
        if(hirda->ErrorCode != HAL_IRDA_ERROR_NONE)
        {
            /* IRDA in mode Receiver ---------------------------------------------------*/
            if(((isrflags & USART_ISR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET))
            {
                IRDA_Receive_IT(hirda);
            }

            /* If Overrun error occurs, or if any error occurs in DMA mode reception,
            consider error as blocking */
            if (((hirda->ErrorCode & HAL_UART_ERROR_ORE) != RESET) ||
                    (HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR)))
            {
                /* Blocking error : transfer is aborted
                Set the IRDA state ready to be able to start again the process,
                Disable Rx Interrupts, and disable Rx DMA request, if ongoing */
                IRDA_EndRxTransfer(hirda);

                /* Disable the IRDA DMA Rx request if enabled */
                if (HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
                {
                    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

                    /* Abort the IRDA DMA Rx channel */
                    if(hirda->hdmarx != NULL)
                    {
                        /* Set the IRDA DMA Abort callback :
                        will lead to call HAL_IRDA_ErrorCallback() at end of DMA abort procedure */
                        hirda->hdmarx->XferAbortCallback = IRDA_DMAAbortOnError;

                        /* Abort DMA RX */
                        if(HAL_DMA_Abort_IT(hirda->hdmarx) != HAL_OK)
                        {
                          /* Call Directly hirda->hdmarx->XferAbortCallback function in case of error */
                          hirda->hdmarx->XferAbortCallback(hirda->hdmarx);
                        }
                    }
                    else
                    {
                        /* Call user error callback */
                        HAL_IRDA_ErrorCallback(hirda);
                    }
                }
                else
                {
                    /* Call user error callback */
                    HAL_IRDA_ErrorCallback(hirda);
                }
            }
            else
            {
                /* Non Blocking error : transfer could go on.
                Error is notified to user through user error callback */
                HAL_IRDA_ErrorCallback(hirda);
                hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
            }
        }
        return;

    } /* End if some error occurs */

    /* IRDA in mode Transmitter ------------------------------------------------*/
    if(((isrflags & USART_ISR_TXE) != RESET) && ((cr1its & USART_CR1_TXEIE) != RESET))
    {
        IRDA_Transmit_IT(hirda);
        return;
    }

    /* IRDA in mode Transmitter (transmission end) -----------------------------*/
    if(((isrflags & USART_ISR_TC) != RESET) && ((cr1its & USART_CR1_TCIE) != RESET))
    {
        IRDA_EndTransmit_IT(hirda);
        return;
    }
}

/**
  * @brief  End ongoing Tx transfer on IRDA peripheral (following error detection or Transmit completion).
  * @param  hirda: IRDA handle.
  * @retval None
  */
static void IRDA_EndTxTransfer(IRDA_HandleTypeDef *hirda)
{
    /* Disable TXEIE and TCIE interrupts */
    CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE));

    /* At end of Tx process, restore hirda->gState to Ready */
    hirda->gState = HAL_IRDA_STATE_READY;
}

/**
  * @brief  End ongoing Rx transfer on IRDA peripheral (following error detection or Reception completion).
  * @param  hirda: IRDA handle.
  * @retval None
  */
static void IRDA_EndRxTransfer(IRDA_HandleTypeDef *hirda)
{
    /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
    CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE));
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

    /* At end of Rx process, restore huart->RxState to Ready */
    hirda->RxState = HAL_IRDA_STATE_READY;
}

/**
  * @brief  Tx Transfer complete callbacks.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_TxHalfCpltCallback(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function should not be modified, when the callback is needed,
              the HAL_IRDA_TxHalfCpltCallback can be implemented in the user file
     */
}

/**
  * @brief  Tx Half Transfer completed callbacks.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified USART module.
  * @retval None
  */
__weak void HAL_IRDA_TxCpltCallback(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function should not be modified, when the callback is needed,
              the HAL_IRDA_TxCpltCallback can be implemented in the user file
     */
}

/**
  * @brief  Rx Transfer complete callbacks.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_RxHalfCpltCallback(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function should not be modified, when the callback is needed,
              the HAL_IRDA_RxHalfCpltCallback can be implemented in the user file
     */
}

/**
  * @brief  Rx Half Transfer complete callbacks.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_RxCpltCallback(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function should not be modified, when the callback is needed,
              the HAL_IRDA_RxCpltCallback can be implemented in the user file
     */
}

/**
  * @brief IRDA error callbacks.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_ErrorCallback(IRDA_HandleTypeDef *hirda)
{
    /* Prevent unused argument(s) compilation warning */
    UNUSED(hirda);

    /* NOTE : This function should not be modified, when the callback is needed,
              the HAL_IRDA_ErrorCallback can be implemented in the user file
     */
}

/**
  * @}
  */

/** @defgroup IRDA_Exported_Functions_Group3 Peripheral Control functions
  *  @brief   IRDA control functions
  *
@verbatim
 ===============================================================================
                      ##### Peripheral Control functions #####
 ===============================================================================
    [..]
    This subsection provides a set of functions allowing to control the IRDA.
     (+) HAL_IRDA_GetState() API can be helpful to check in run-time the state of the IRDA peripheral.
     (+) IRDA_SetConfig() API is used to configure the IRDA communications parameters.
@endverbatim
  * @{
  */

/**
  * @brief  Returns the IRDA state.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL state
  */
HAL_IRDA_StateTypeDef HAL_IRDA_GetState(IRDA_HandleTypeDef *hirda)
{
    uint32_t temp1 = 0x00U, temp2 = 0x00U;
    temp1 = hirda->gState;
    temp2 = hirda->RxState;

    return (HAL_IRDA_StateTypeDef)(temp1 | temp2);
}

/**
  * @brief  Return the IRDA error code
  * @param  hirda : pointer to a IRDA_HandleTypeDef structure that contains
  *              the configuration information for the specified IRDA.
* @retval IRDA Error Code
*/
uint32_t HAL_IRDA_GetError(IRDA_HandleTypeDef *hirda)
{
    uint32_t temp1 = 0x00U, temp2 = 0x00U;
    temp1 = hirda->gState;
    temp2 = hirda->RxState;

    return (HAL_IRDA_StateTypeDef)(temp1 | temp2);
}

/**
  * @}
  */

/**
  * @brief Configure the IRDA peripheral
  * @param hirda: irda handle
  * @retval None
  */
static void IRDA_SetConfig(IRDA_HandleTypeDef *hirda)
{
    uint32_t tmpreg      = 0x00000000U;
    uint32_t clocksource = 0x00000000U;

    /* Check the communication parameters */
    assert_param(IS_IRDA_BAUDRATE(hirda->Init.BaudRate));
    assert_param(IS_IRDA_WORD_LENGTH(hirda->Init.WordLength));
    assert_param(IS_IRDA_PARITY(hirda->Init.Parity));
    assert_param(IS_IRDA_TX_RX_MODE(hirda->Init.Mode));
    assert_param(IS_IRDA_PRESCALER(hirda->Init.Prescaler));
    assert_param(IS_IRDA_POWERMODE(hirda->Init.PowerMode));
    /*-------------------------- USART CR1 Configuration -----------------------*/
    /* Configure the IRDA Word Length, Parity and transfer Mode:
    Set the M bits according to hirda->Init.WordLength value
    Set PCE and PS bits according to hirda->Init.Parity value
    Set TE and RE bits according to hirda->Init.Mode value */
    tmpreg = (uint32_t)hirda->Init.WordLength | hirda->Init.Parity | hirda->Init.Mode ;

    MODIFY_REG(hirda->Instance->CR1, IRDA_CR1_FIELDS, tmpreg);

    /*-------------------------- USART CR3 Configuration -----------------------*/
    MODIFY_REG(hirda->Instance->CR3, USART_CR3_IRLP, hirda->Init.PowerMode);

    /*-------------------------- USART GTPR Configuration ----------------------*/
    MODIFY_REG(hirda->Instance->GTPR, (uint32_t)USART_GTPR_PSC, hirda->Init.Prescaler);

    /*-------------------------- USART BRR Configuration -----------------------*/
    IRDA_GETCLOCKSOURCE(hirda, clocksource);
    switch (clocksource)
    {
    case IRDA_CLOCKSOURCE_PCLK1:
        hirda->Instance->BRR = (uint16_t)((HAL_RCC_GetPCLK1Freq() + (hirda->Init.BaudRate/2))/ hirda->Init.BaudRate);
        break;
    case IRDA_CLOCKSOURCE_PCLK2:
        hirda->Instance->BRR = (uint16_t)((HAL_RCC_GetPCLK2Freq() + (hirda->Init.BaudRate/2))/ hirda->Init.BaudRate);
        break;
    case IRDA_CLOCKSOURCE_HSI:
        hirda->Instance->BRR = (uint16_t)((HSI_VALUE + (hirda->Init.BaudRate/2))/ hirda->Init.BaudRate);
        break;
    case IRDA_CLOCKSOURCE_SYSCLK:
        hirda->Instance->BRR = (uint16_t)((HAL_RCC_GetSysClockFreq() + (hirda->Init.BaudRate/2))/ hirda->Init.BaudRate);
        break;
    case IRDA_CLOCKSOURCE_LSE:
        hirda->Instance->BRR = (uint16_t)((LSE_VALUE + (hirda->Init.BaudRate/2))/ hirda->Init.BaudRate);
        break;
    default:
        break;
    }
}

/**
  * @brief Check the IRDA Idle State
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_CheckIdleState(IRDA_HandleTypeDef *hirda)
{
    uint32_t tickstart = 0U;

    /* Initialize the IRDA ErrorCode */
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;

    /* Init tickstart for timeout managment*/
    tickstart = HAL_GetTick();

    /* Check if the Transmitter is enabled */
    if((hirda->Instance->CR1 & USART_CR1_TE) == USART_CR1_TE)
    {
        /* Wait until TEACK flag is set */
        if(IRDA_WaitOnFlagUntilTimeout(hirda, USART_ISR_TEACK, RESET, tickstart, TEACK_REACK_TIMEOUT) != HAL_OK)
        {
            return HAL_TIMEOUT;
        }
    }
    /* Check if the Receiver is enabled */
    if((hirda->Instance->CR1 & USART_CR1_RE) == USART_CR1_RE)
    {
        if(IRDA_WaitOnFlagUntilTimeout(hirda, USART_ISR_REACK, RESET, tickstart, TEACK_REACK_TIMEOUT) != HAL_OK)
        {
            return HAL_TIMEOUT;
        }
    }
    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    /* Initialize the IRDA state*/
    hirda->gState= HAL_IRDA_STATE_READY;
    hirda->RxState= HAL_IRDA_STATE_READY;

    return HAL_OK;
}

/**
  * @brief  This function handles IRDA Communication Timeout.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  Flag specifies the IRDA flag to check.
  * @param  Status The new Flag status (SET or RESET).
  * @param  Tickstart Tick start value
  * @param  Timeout Timeout duration
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_WaitOnFlagUntilTimeout(IRDA_HandleTypeDef *hirda, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout)
{
    /* Wait until flag is set */
    while((__HAL_IRDA_GET_FLAG(hirda, Flag) ? SET : RESET) == Status)
    {
        /* Check for the Timeout */
        if(Timeout != HAL_MAX_DELAY)
        {
            if((Timeout == 0)||((HAL_GetTick() - Tickstart ) > Timeout))
            {
                /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */
                CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE));
                CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

                hirda->gState= HAL_IRDA_STATE_READY;
                hirda->RxState= HAL_IRDA_STATE_READY;

                /* Process Unlocked */
                __HAL_UNLOCK(hirda);

                return HAL_TIMEOUT;
            }
        }
    }
    return HAL_OK;
}

/**
  * @brief  Send an amount of data in non blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda)
{
    uint16_t* tmp;

    /* Check that a Tx process is ongoing */
    if(hirda->gState == HAL_IRDA_STATE_BUSY_TX)
    {
        if(hirda->Init.WordLength == IRDA_WORDLENGTH_9B)
        {
            tmp = (uint16_t*) hirda->pTxBuffPtr;
            hirda->Instance->RDR = (uint16_t)(*tmp & (uint16_t)0x01FFU);
            if(hirda->Init.Parity == IRDA_PARITY_NONE)
            {
                hirda->pTxBuffPtr += 2U;
            }
            else
            {
                hirda->pTxBuffPtr += 1U;
            }
        }
        else
        {
            hirda->Instance->RDR = (uint8_t)(*hirda->pTxBuffPtr++ & (uint8_t)0x00FFU);
        }

        if(--hirda->TxXferCount == 0U)
        {
            /* Disable the IRDA Transmit Data Register Empty Interrupt */
            CLEAR_BIT(hirda->Instance->CR1, USART_CR1_TXEIE);

            /* Enable the IRDA Transmit Complete Interrupt */
            SET_BIT(hirda->Instance->CR1, USART_CR1_TCIE);
        }

        return HAL_OK;
    }
    else
    {
        return HAL_BUSY;
    }
}

/**
  * @brief  Wraps up transmission in non blocking mode.
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_EndTransmit_IT(IRDA_HandleTypeDef *hirda)
{
    /* Disable the IRDA Transmit Complete Interrupt */
    CLEAR_BIT(hirda->Instance->CR1, USART_CR1_TCIE);

    /* Disable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

    /* Tx process is ended, restore hirda->gState to Ready */
    hirda->gState = HAL_IRDA_STATE_READY;

    HAL_IRDA_TxCpltCallback(hirda);

    return HAL_OK;
}

/**
  * @brief Receive an amount of data in non blocking mode.
  *         Function called under interruption only, once
  *         interruptions have been enabled by HAL_IRDA_Receive_IT()
  * @param  hirda: pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_Receive_IT(IRDA_HandleTypeDef *hirda)
{
    uint16_t* tmp;
    uint16_t  uhdata;
    uint16_t  uhMask = hirda->Mask;

    if(hirda->RxState == HAL_IRDA_STATE_BUSY_RX)
    {
        uhdata = (uint16_t) READ_REG(hirda->Instance->RDR);
        if ((hirda->Init.WordLength == IRDA_WORDLENGTH_9B) && (hirda->Init.Parity == IRDA_PARITY_NONE))
        {
            tmp = (uint16_t*) hirda->pRxBuffPtr ;
            *tmp = (uint16_t)(uhdata & uhMask);
            hirda->pRxBuffPtr  +=2U;
        }
        else
        {
            *hirda->pRxBuffPtr++ = (uint8_t)(uhdata & (uint8_t)uhMask);
        }

        if(--hirda->RxXferCount == 0U)
        {
            CLEAR_BIT(hirda->Instance->CR1, USART_CR1_RXNEIE);

            /* Disable the IRDA Parity Error Interrupt */
            CLEAR_BIT(hirda->Instance->CR1, USART_CR1_PEIE);

            /* Disable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
            CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

            /* Rx process is completed, restore hirda->RxState to Ready */
            hirda->RxState = HAL_IRDA_STATE_READY;

            HAL_IRDA_RxCpltCallback(hirda);

            return HAL_OK;
        }
        return HAL_OK;
    }
    else
    {
        /* Clear RXNE interrupt flag */
        __HAL_IRDA_SEND_REQ(hirda, IRDA_RXDATA_FLUSH_REQUEST);
        return HAL_BUSY;
    }
}

/**
  * @brief DMA IRDA Tx transfer completed callback
  * @param  hdma: pointer to a DMA_HandleTypeDef structure that contains
  *                the configuration information for the specified DMA module.
  * @retval None
  */
static void IRDA_DMATransmitCplt(DMA_HandleTypeDef *hdma)
{
    IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

    /* DMA Normal mode*/
    if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U)
    {
        hirda->TxXferCount = 0U;

        /* Disable the DMA transfer for transmit request by setting the DMAT bit
           in the IRDA CR3 register */
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

        /* Enable the IRDA Transmit Complete Interrupt */
        SET_BIT(hirda->Instance->CR1, USART_CR1_TCIE);
    }
    /* DMA Circular mode */
    else
    {
        HAL_IRDA_TxCpltCallback(hirda);
    }
}

/**
  * @brief DMA IRDA receive process half complete callback
  * @param  hdma: pointer to a DMA_HandleTypeDef structure that contains
  *                the configuration information for the specified DMA module.
  * @retval None
  */
static void IRDA_DMATransmitHalfCplt(DMA_HandleTypeDef *hdma)
{
    IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

    HAL_IRDA_TxHalfCpltCallback(hirda);
}

/**
  * @brief DMA IRDA Rx Transfer completed callback
  * @param hdma: DMA handle
  * @retval None
  */
static void IRDA_DMAReceiveCplt(DMA_HandleTypeDef *hdma)
{
    IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

    /* DMA Normal mode */
    if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U)
    {
        hirda->RxXferCount = 0U;

        /* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
        CLEAR_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

        /* Disable the DMA transfer for the receiver request by setting the DMAR bit
           in the IRDA CR3 register */
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

        /* At end of Rx process, restore hirda->RxState to Ready */
        hirda->RxState = HAL_IRDA_STATE_READY;
    }

    HAL_IRDA_RxCpltCallback(hirda);
}

/**
  * @brief DMA IRDA receive process half complete callback
  * @param  hdma: pointer to a DMA_HandleTypeDef structure that contains
  *                the configuration information for the specified DMA module.
  * @retval None
  */
static void IRDA_DMAReceiveHalfCplt(DMA_HandleTypeDef *hdma)
{
    IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

    HAL_IRDA_RxHalfCpltCallback(hirda);
}

/**
  * @brief DMA IRDA communication error callback
  * @param hdma: DMA handle
  * @retval None
  */
static void IRDA_DMAError(DMA_HandleTypeDef *hdma)
{
    IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

    hirda->RxXferCount = 0U;
    hirda->TxXferCount = 0U;

    /* Stop IRDA DMA Tx request if ongoing */
    if (  (hirda->gState == HAL_IRDA_STATE_BUSY_TX)
            &&(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT)) )
    {
        IRDA_EndTxTransfer(hirda);
    }

    /* Stop IRDA DMA Rx request if ongoing */
    if (  (hirda->RxState == HAL_IRDA_STATE_BUSY_RX)
            &&(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR)) )
    {
        IRDA_EndRxTransfer(hirda);
    }

    hirda->ErrorCode |= HAL_IRDA_ERROR_DMA;

    HAL_IRDA_ErrorCallback(hirda);
}

/**
  * @}
  */

/**
  * @}
  */

#endif /* HAL_IRDA_MODULE_ENABLED */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/