.. _it82xx2_evb:

ITE IT82XX2 series
######################

Overview
********

The IT82XX2 is a 32-bit RISC-V microcontroller.
And a highly integrated embedded controller with system functions.
It is suitable for mobile system applications. The picture below is
the IT82202 development board (also known as it82xx2_evb) and its debug card.

.. figure:: it82xx2_evb_and_debug_card.jpg
     :align: center
     :alt: IT82202 EVB

To find out more about ITE, visit our World Wide Web at:`ITE's website`_

Hardware
********
The IT82XX2 series contains different chip types(ex, it82202, it82302),
and they support different hardware features.
Listing the IT82202 hardware features as following:

- RISC-V RV32IMAFC instruction set
- 4KB instruction cache size
- 256KB SRAM in total
- Built-in 32.768 kHz clock generator
- Embedded Flash, 512K/1024K-byte e-flash
- eSPI, SSPI, SPI slave, BRAM, KBC, PECI, UART
- GPIO, PWM, ADC, INTC, WUC, Timer, Watchdog, KB scan, JTAG
- Support 6 Voltage Comparator
- Support Cryptographic Engine
- 6 SMBus channels, with 6 DMA controller, compatible with I2C
- USB 2.0 Full-speed Controller
- USB Type-c CC Logic
- USB Power Delivery


Supported Features
==================
currently supports the following hardware features:

.. list-table:: Supported Features
   :header-rows: 1
   :widths: auto

   * - Interface
     - Controller
     - Driver/Component
   * - NVIC
     - on-chip
     - interrupt controller
   * - FLASH
     - on-chip
     - flash controller
   * - PINCTRL
     - on-chip
     - pin controller
   * - ESPI
     - on-chip
     - espi
   * - PECI
     - on-chip
     - peci
   * - UART
     - on-chip
     - serial
   * - GPIO
     - on-chip
     - gpio
   * - PWM
     - on-chip
     - pwm
   * - ADC
     - on-chip
     - adc
   * - TIMER
     - on-chip
     - timer
   * - WATCHDOG
     - on-chip
     - watchdog
   * - KSCAN
     - on-chip
     - kscan
   * - SENSOR
     - on-chip
     - voltage comparator
   * - I2C
     - on-chip
     - i2c


Other hardware features are not currently supported by Zephyr.

The default configuration can be found in the
:zephyr_file:`boards/ite/it82xx2_evb/it82xx2_evb_defconfig` Kconfig file.

Programming and debugging on it82202
************************************

In order to upload the application to the device,
you'll need our flash tool and Download board.
You can get them at: `ITE's website`_.

Wiring
=======
#. Connect the Download Board to your host computer using the USB cable.

#. Connect the it82xx2_evb to the evolution motherboard.

#. Connect the Download Board J5 to J41 on the evolution motherboard.

#. Connect the USB to UART wire to J33 on the evolution motherboard.

   .. image:: it82xx2_evb_wiring.jpg
        :align: center
        :alt: it82xx2_evb wiring

   .. note:: Be careful during connection!
    Use separate wires to connect I2C pins with pins on the it82xx2_evb board.
    Wiring connection is described in the table below.

    +-------------+---------------+
    |   J5        | it82xx2_evb   |
    |   Connector | J41 Connector |
    +=============+===============+
    |      2      |      E0       |
    +-------------+---------------+
    |      3      |      E7       |
    +-------------+---------------+
    |      4      |      GND      |
    +-------------+---------------+

    For USB to UART cable, connect the evolution motherboard as below:

    +-------------+---------------+
    | USB to UART | Evolution     |
    | cable       | motherboard   |
    |             | J33 Connector |
    +=============+===============+
    |     RX      |      B0       |
    +-------------+---------------+
    |     TX      |      B1       |
    +-------------+---------------+
    |     GND     |      GND      |
    +-------------+---------------+

Building
========

#. Build :ref:`hello_world` application as you would normally do
   (see :`Zephyr Getting Started Guide`_):.

   .. zephyr-app-commands::
      :board: it82xx2_evb
      :zephyr-app: samples/hello_world
      :goals: build

#. The file :file:`zephyr.bin` will be created by west.

Flashing
========

Windows
--------

Use the winflash tool to program a zephyr application
to the it82xx2 board flash.

#. Open the winflash tool and make sure the order you open the switch is right.
   First, turn on the Download board switch.
   Second, turn on the it82xx2_evb board switch.
   Then, configure your winflash tool like below.

    .. figure:: WinFlashTool_P2.jpg
          :align: center

    .. figure:: WinFlashTool_P4.jpg

#. Using the winflash tool flash ``zephyr.bin`` into your ITE board.
   First, click the ``Load`` button and select your ``zephyr.bin`` file.
   Second, click ``run`` to flash the image into board.

    .. figure:: WinFlashTool_P3.jpg
          :align: center

#. At this point, you have flashed your image into ITE board and
   it will work if you turn on the ITE board. You can use a terminal program
   to verify flashing worked correctly.

   For example, open device manager to find the USB Serial Port(COM4) and use your
   terminal program to connect it(Speed: 115200).

    .. figure:: WinFlashTool_P1.jpg
          :align: center

#. Turn on the it82xx2_evb board switch, you should see ``"Hello World! it82xx2_evb"``
   sent by the board. If you don't see this message, press the Reset button and the
   message should appear.

Ubuntu
--------

#. Run your favorite terminal program to listen for output.
   Under Linux the terminal should be :code:`/dev/ttyUSB0`. Do not close it.

   For example:

   .. code-block:: console

      $ minicom -D /dev/ttyUSB0 -b 115200

#. Open a second terminal window and use the Linux flash tool to flash your board.

   .. code-block:: console

      $ sudo ~/itetool/ite -f build/zephyr/zephyr.bin

   .. note:: The source code of ITE tool can be downloaded here:
    https://www.ite.com.tw/uploads/product_download/itedlb4-linux-v106.tar.bz2

#. Split first and second terminal windows to view both of them.
   You should see ``"Hello World! it82xx2_evb"`` in the first terminal window.
   If you don't see this message, press the Reset button and the message should appear.

Debugging
=========

it82xx2_evb board can be debugged by connecting USB to UART. We can write commands and
read messages through minicom in the Ubuntu terminal.

Troubleshooting
===============

#. If the flash tool reports a failure, re-plug the 8390 Download board or
   power cycle the it82xx2_evb board and try again.

References
==========

.. target-notes::

.. _ITE's website: https://www.ite.com.tw/zh-tw/product/view?mid=169
.. _Zephyr Getting Started Guide: https://docs.zephyrproject.org/latest/getting_started/index.html