# Copyright (c) 2024 STMicroelectronics
# SPDX-License-Identifier: Apache-2.0

description: |
    When setting the odr, power-mode, and range properties in a .dts or .dtsi file you may include
    st_lis2dux12.h and use the macros defined there.
    Example:
    #include <zephyr/dt-bindings/sensor/st_lis2dux12.h>
    lis2dux12: lis2dux12@0 {
      ...
      power-mode = <LIS2DUX12_OPER_MODE_LOW_POWER>;
      odr = <LIS2DUX12_DT_ODR_12Hz5>;
      range = <LIS2DUX12_DT_FS_16G>;
    };

include: sensor-device.yaml

properties:
  int1-gpios:
    type: phandle-array
    description: |
      INT1 pin

      This pin defaults to active high when produced by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.
  int2-gpios:
    type: phandle-array
    description: |
      INT2 pin

      This pin defaults to active high when produced by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.

  drdy-pin:
    type: int
    default: 1
    enum:
      - 1 # drdy is generated from INT1
      - 2 # drdy is generated from INT2
    description: |
      Select DRDY pin number (1 or 2).
      This number represents which of the two interrupt pins
      (INT1 or INT2) the drdy line is attached to. This property is not
      mandatory and if not present it defaults to 1 which is the
      configuration at power-up.


  range:
    type: int
    default: 0
    description: |
      Range in g. Default is power-up configuration.

      - 3  # LIS2DUX12_DT_FS_16G
      - 2  # LIS2DUX12_DT_FS_8G
      - 1  # LIS2DUX12_DT_FS_4G
      - 0  # LIS2DUX12_DT_FS_2G

    enum: [0, 1, 2, 3]

  power-mode:
    type: int
    default: 0
    description: |
      Specify the sensor power mode. Default is power-down mode

      - 0 # LIS2DUX12_OPER_MODE_POWER_DOWN
      - 1 # LIS2DUX12_OPER_MODE_LOW_POWER
      - 2 # LIS2DUX12_OPER_MODE_HIGH_RESOLUTION
      - 3 # LIS2DUX12_OPER_MODE_HIGH_FREQUENCY

    enum: [0, 1, 2, 3]

  odr:
    type: int
    default: 0
    description: |
      Specify the default output data rate expressed in samples per second (Hz).
      Default is power-down mode
      - 0  # LIS2DUX12_DT_ODR_OFF
      - 1  # LIS2DUX12_DT_ODR_1Hz_ULP
      - 2  # LIS2DUX12_DT_ODR_3Hz_ULP
      - 3  # LIS2DUX12_DT_ODR_25Hz_ULP
      - 4  # LIS2DUX12_DT_ODR_6Hz
      - 5  # LIS2DUX12_DT_ODR_12Hz5
      - 6  # LIS2DUX12_DT_ODR_25Hz
      - 7  # LIS2DUX12_DT_ODR_50Hz
      - 8  # LIS2DUX12_DT_ODR_100Hz
      - 9  # LIS2DUX12_DT_ODR_200Hz
      - 10 # LIS2DUX12_DT_ODR_400Hz
      - 11 # LIS2DUX12_DT_ODR_800Hz

    enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11]