.. _nrf9160_pca10090:

nRF9160-PCA10090
################

Overview
********

The nRF9160 PCA10090 is a single-board development kit for evaluation
and development on the nRF9160 SiP for LTE-M and NB-IoT. The
nrf9160_pca10090 board provides support for the Nordic Semiconductor
nRF9160 ARM Cortex-M33F CPU with ARMv8-M Security Extension and the
following devices:

* :abbr:`ADC (Analog to Digital Converter)`
* CLOCK
* FLASH
* :abbr:`GPIO (General Purpose Input Output)`
* :abbr:`I2C (Inter-Integrated Circuit)`
* :abbr:`MPU (Memory Protection Unit)`
* :abbr:`NVIC (Nested Vectored Interrupt Controller)`
* :abbr:`PWM (Pulse Width Modulation)`
* :abbr:`RTC (nRF RTC System Clock)`
* Segger RTT (RTT Console)
* :abbr:`SPI (Serial Peripheral Interface)`
* :abbr:`UARTE (Universal asynchronous receiver-transmitter with EasyDMA)`
* :abbr:`WDT (Watchdog Timer)`
* :abbr:`IDAU (Implementation Defined Attribution Unit)`

.. figure:: img/nrf9160_pca10090.png
     :width: 711px
     :align: center
     :alt: nRF9160 PCA10090 DK

     nRF9160 PCA10090 DK (Credit: Nordic Semiconductor)

More information about the board can be found at the
`nRF91 DK website`_. The `Nordic Semiconductor Infocenter`_
contains the processor's information and the datasheet.

Hardware
********

nRF9160 DK has two external oscillators. The frequency of
the slow clock is 32.768 kHz. The frequency of the main clock
is 32 MHz.

Supported Features
==================

The nrf9160_pca10090 board configuration supports the following
hardware features:

+-----------+------------+----------------------+
| Interface | Controller | Driver/Component     |
+===========+============+======================+
| ADC       | on-chip    | adc                  |
+-----------+------------+----------------------+
| CLOCK     | on-chip    | clock_control        |
+-----------+------------+----------------------+
| FLASH     | on-chip    | flash                |
+-----------+------------+----------------------+
| GPIO      | on-chip    | gpio                 |
+-----------+------------+----------------------+
| I2C(M)    | on-chip    | i2c                  |
+-----------+------------+----------------------+
| MPU       | on-chip    | arch/arm             |
+-----------+------------+----------------------+
| NVIC      | on-chip    | arch/arm             |
+-----------+------------+----------------------+
| PWM       | on-chip    | pwm                  |
+-----------+------------+----------------------+
| RTC       | on-chip    | system clock         |
+-----------+------------+----------------------+
| RTT       | Segger     | console              |
+-----------+------------+----------------------+
| SPI(M/S)  | on-chip    | spi                  |
+-----------+------------+----------------------+
| SPU       | on-chip    | system protection    |
+-----------+------------+----------------------+
| UARTE     | on-chip    | serial               |
+-----------+------------+----------------------+
| WDT       | on-chip    | watchdog             |
+-----------+------------+----------------------+

Other hardware features are not supported by the Zephyr kernel.
See `nRF91 DK website`_ and `Nordic Semiconductor Infocenter`_
for a complete list of nRF9160 Development Kit board hardware features.

Connections and IOs
===================

LED
---

* LED1 (green) = P0.2
* LED2 (green) = P0.3
* LED3 (green) = P0.4
* LED4 (green) = P0.5

Push buttons and Switches
-------------------------

* BUTTON1 = P0.6
* BUTTON2 = P0.7
* SWITCH1 = P0.8
* SWITCH2 = P0.9
* BOOT = SW5 = boot/reset

Security components
===================

- Implementation Defined Attribution Unit (`IDAU`_).  The IDAU is implemented
  with the System Protection Unit and is used to define secure and non-secure
  memory maps.  By default, all of the memory space  (Flash, SRAM, and
  peripheral address space) is defined to be secure accessible only.
- Secure boot.


Programming and Debugging
*************************

nrf9160_pca10090 supports the Armv8m Security Extension, and by default boots
in the Secure state.

Building Secure/Non-Secure Zephyr applications
==============================================

The process requires the following steps:

1. Build the Secure Zephyr application using ``-DBOARD=nrf9160_pca10090`` and
   ``CONFIG_TRUSTED_EXECUTION_SECURE=y`` in the the application project configuration file.
2. Build the Non-Secure Zephyr application using ``-DBOARD=nrf9160_pca10090ns``.
3. Merge the two binaries together.

When building a Secure/Non-Secure application, the Secure application will
have to set the IDAU (SPU) configuration to allow Non-Secure access to all
CPU resources utilized by the Non-Secure application firmware. SPU
configuration shall take place before jumping to the Non-Secure application.

Building a Secure only application
==================================

Build the Zephyr app in the usual way (see :ref:`build_an_application`
and :ref:`application_run`), using ``-DBOARD=nrf9160_pca10090``.


Flashing
========

Follow the instructions in the :ref:`nordic_segger` page to install
and configure all the necessary software. Further information can be
found in :ref:`nordic_segger_flashing`. Then build and flash
applications as usual (see :ref:`build_an_application` and
:ref:`application_run` for more details).

Here is an example for the :ref:`hello_world` application.

First, run your favorite terminal program to listen for output.

.. code-block:: console

   $ minicom -D <tty_device> -b 115200

Replace :code:`<tty_device>` with the port where the board nRF9160 DK
can be found. For example, under Linux, :code:`/dev/ttyACM0`.

Then build and flash the application in the usual way.

.. zephyr-app-commands::
   :zephyr-app: samples/hello_world
   :board: nrf9160_pca10090
   :goals: build flash

Debugging
=========

Refer to the :ref:`nordic_segger` page to learn about debugging Nordic boards with a
Segger IC.


Testing the LEDs and buttons in the nRF9160 DK
**********************************************

There are 2 samples that allow you to test that the buttons (switches) and LEDs on
the board are working properly with Zephyr:

* :ref:`blinky-sample`
* :ref:`button-sample`

You can build and flash the examples to make sure Zephyr is running correctly on
your board. The button and LED definitions can be found in
:zephyr_file:`boards/arm/nrf9160_pca10090/nrf9160_pca10090_common.dts`.

References
**********

.. target-notes::

.. _IDAU:
   https://developer.arm.com/products/architecture/cpu-architecture/m-profile/docs/100690/latest/attribution-units-sau-and-idau
.. _nRF91 DK website: https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF9160-DK
.. _Nordic Semiconductor Infocenter: https://infocenter.nordicsemi.com