# Kconfig - SPI driver configuration options

#
# Copyright (c) 2015 Intel Corporation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#

#
# SPI Drivers
#
menuconfig SPI
	bool
	prompt "SPI hardware bus support"
	default n
	help
	  Enable support for the SPI hardware bus.

if SPI
config  SPI_DEBUG
	bool
	prompt "SPI drivers debug output"
	depends on SPI
	default n
	help
	  Enable debug output for SPI drivers

config  SPI_INTEL
	bool
	prompt "Intel SPI controller driver"
	depends on SPI && CPU_MINUTEIA
	default n
	help
	  Enable support for Intel's SPI controllers. Such controller
	  was formelly found on XScale chips. It can be found nowadays
	  on CEXXXX Intel media controller and Quark CPU (2 of them).

choice
depends on SPI_INTEL
prompt "Intel SPI interrupt trigger condition"
default SPI_INTEL_RISING_EDGE

config SPI_INTEL_FALLING_EDGE
	bool "Falling edge"
	help
	  "Intel SPI uses falling edge interrupt"

config SPI_INTEL_RISING_EDGE
	bool "Rising edge"
	help
	  "Intel SPI uses rising edge interrupt"

config SPI_INTEL_LEVEL_HIGH
	bool "Level high"
	help
	  "Intel SPI uses level high interrupt"

config SPI_INTEL_LEVEL_LOW
	bool "Level low"
	help
	  "Intel SPI uses level low interrupt"
endchoice

config	SPI_INTEL_VENDOR_ID
	hex "PCI Vendor ID"
	depends on SPI_INTEL && PCI
	default 0x8086

config	SPI_INTEL_DEVICE_ID
	hex "PCI Device ID"
	depends on SPI_INTEL && PCI
	default 0x935

config	SPI_INTEL_CLASS
	hex "PCI class"
	depends on SPI_INTEL && PCI
	default 0x0C

config  SPI_INTEL_CS_GPIO
	bool "SPI port CS pin is controlled via a GPIO port"
	depends on SPI_INTEL && GPIO
	default n

config SPI_INTEL_INIT_PRIORITY
	int
	prompt "Init priority"
	depends on SPI_INTEL
	default 60
	help
	  Device driver initialization priority.

config	SPI_INTEL_PORT_0
	bool
	prompt "Intel SPI port 0"
	depends on SPI_INTEL
	default n
	help
	  Enable Intel's SPI controller port 0.

config  SPI_INTEL_PORT_0_DRV_NAME
	string
	prompt "Intel SPI port 0 device name"
	depends on SPI_INTEL_PORT_0
	default "intel_spi_0"

config	SPI_INTEL_PORT_0_BUS
	int "Port 0 PCI Bus"
	depends on SPI_INTEL_PORT_0 && PCI
	default 0

config  SPI_INTEL_PORT_0_DEV
	int "Port 0 PCI Dev"
	depends on SPI_INTEL_PORT_0 && PCI
	default 0

config  SPI_INTEL_PORT_0_FUNCTION
	int "Port 0 PCI function"
	depends on SPI_INTEL_PORT_0 && PCI
	default 0

config  SPI_INTEL_PORT_0_REGS
	hex
	prompt "Port 0 registers address"
	depends on SPI_INTEL_PORT_0
	default 0x00000000

config  SPI_INTEL_PORT_0_IRQ
	int
	prompt "Port 0 interrupt"
	depends on SPI_INTEL_PORT_0
	default 0

config  SPI_INTEL_PORT_0_PRI
	int
	prompt "Port 0 interrupt priority"
	depends on SPI_INTEL_PORT_0
	default 2

config  SPI_INTEL_PORT_0_CS_GPIO_PORT
	string
	prompt "The GPIO port which is used to control CS"
	depends on SPI_INTEL_PORT_0 && SPI_INTEL_CS_GPIO
	default GPIO_DW_0_NAME

config  SPI_INTEL_PORT_0_CS_GPIO_PIN
	int "The GPIO PIN which is used to act as a CS pin"
	depends on SPI_INTEL_PORT_0 && SPI_INTEL_CS_GPIO
	default 0

config  SPI_INTEL_PORT_1
	bool
	prompt "Intel SPI port 1"
	depends on SPI_INTEL
	default n
	help
	  Enable Intel's SPI controller port 1.

config  SPI_INTEL_PORT_1_DRV_NAME
	string
	prompt "Intel SPI port 1 device name"
	depends on SPI_INTEL_PORT_1
	default "intel_spi_1"

config	SPI_INTEL_PORT_1_BUS
	int "Port 1 PCI Bus"
	depends on SPI_INTEL_PORT_1 && PCI
	default 0

config  SPI_INTEL_PORT_1_DEV
	int "Port 1 PCI Dev"
	depends on SPI_INTEL_PORT_1 && PCI
	default 0

config  SPI_INTEL_PORT_1_FUNCTION
	int "Port 1 PCI function"
	depends on SPI_INTEL_PORT_1 && PCI
	default 0

config  SPI_INTEL_PORT_1_REGS
	hex
	prompt "Port 1 registers address"
	depends on SPI_INTEL_PORT_1
	default 0x00000000

config  SPI_INTEL_PORT_1_IRQ
	int
	prompt "Port 1 interrupt"
	depends on SPI_INTEL_PORT_1
	default 0

config  SPI_INTEL_PORT_1_PRI
	int
	prompt "Port 0 interrupt priority"
	depends on SPI_INTEL_PORT_1
	default 2

config  SPI_INTEL_PORT_1_CS_GPIO_PORT
	string
	prompt "The GPIO port which is used to control CS"
	depends on SPI_INTEL_PORT_1 && SPI_INTEL_CS_GPIO
	default GPIO_DW_0_NAME

config  SPI_INTEL_PORT_1_CS_GPIO_PIN
	int "The GPIO PIN which is used to act as a CS pin"
	depends on SPI_INTEL_PORT_1 && SPI_INTEL_CS_GPIO
	default 0

config SPI_DW
	bool
	prompt "Designware SPI controller driver"
	depends on SPI
	default n
	help
	  Enable support for Designware's SPI controllers.

config SPI_DW_ARC_AUX_REGS
	bool "Registers are part of ARC auxiliary registers"
	depends on SPI_DW && ARC
	default y
	help
	  SPI IP block registers are part of user extended auxiliary
	  registers and thus their access is different than memory
	  mapped registers.

config SPI_DW_CS_GPIO
	bool "SPI port CS pin is controlled via a GPIO port"
	depends on SPI_DW && GPIO
	default n

config SPI_DW_INIT_PRIORITY
	int "Init priority"
	depends on SPI_DW
	default 60
	help
	  Device driver initialization priority.

choice
depends on SPI_DW
prompt "DesignWare SPI interrupt trigger condition"
default SPI_DW_RISING_EDGE

config SPI_DW_FALLING_EDGE
	bool "Falling edge"
	help
	  "DesignWare SPI uses falling edge interrupt"

config SPI_DW_RISING_EDGE
	bool "Rising edge"
	help
	  "DesignWare SPI uses rising edge interrupt"

config SPI_DW_LEVEL_HIGH
	bool "Level high"
	help
	  "DesignWare SPI uses level high interrupt"

config SPI_DW_LEVEL_LOW
	bool "Level low"
	help
	  "DesignWare SPI uses level low interrupt"
endchoice

config  SPI_DW_CLOCK_GATE
	bool "Enable glock gating"
	depends on SPI_DW && SOC_QUARK_SE
	select CLOCK_CONTROL
	default n

config	SPI_DW_CLOCK_GATE_DRV_NAME
	string
	depends on SPI_DW_CLOCK_GATE
	default ""

config	SPI_DW_PORT_0
	bool
	prompt "Designware SPI port 0"
	depends on SPI_DW
	default n
	help
	  Enable Designware SPI controller port 0.

config  SPI_DW_PORT_0_CLOCK_GATE_SUBSYS
	int "Clock controller's subsystem"
	depends on SPI_DW_CLOCK_GATE
	default 0

config  SPI_DW_PORT_0_CS_GPIO_PORT
	string
	prompt "The GPIO port which is used to control CS"
	depends on SPI_DW_PORT_0 && SPI_DW_CS_GPIO
	default GPIO_DW_0_NAME

config  SPI_DW_PORT_0_CS_GPIO_PIN
	int "The GPIO PIN which is used to act as a CS pin"
	depends on SPI_DW_PORT_0 && SPI_DW_CS_GPIO
	default 0

config  SPI_DW_PORT_0_DRV_NAME
	string
	prompt "Designware SPI port 0 device name"
	depends on SPI_DW_PORT_0
	default "spi_dw_0"

config  SPI_DW_PORT_0_REGS
	hex
	prompt "Port 0 registers address"
	depends on SPI_DW_PORT_0
	default 0x00000000

config  SPI_DW_PORT_0_IRQ
	int
	prompt "Port 0 interrupt"
	depends on SPI_DW_PORT_0
	default 0

config  SPI_DW_PORT_0_PRI
	int
	prompt "Port 0 interrupt priority"
	depends on SPI_DW_PORT_0
	default 2

config  SPI_DW_PORT_1
	bool
	prompt "Designware SPI port 1"
	depends on SPI_DW
	default n
	help
	  Enable Designware SPI controller port 1.

config  SPI_DW_PORT_1_CLOCK_GATE_SUBSYS
	int "Clock controller's subsystem"
	depends on SPI_DW_CLOCK_GATE
	default 0

config  SPI_DW_PORT_1_CS_GPIO_PORT
	string
	prompt "The GPIO port which is used to control CS"
	depends on SPI_DW_PORT_0 && SPI_DW_CS_GPIO
	default GPIO_DW_0_NAME

config  SPI_DW_PORT_1_CS_GPIO_PIN
	int "The GPIO PIN which is used to act as a CS pin"
	depends on SPI_DW_PORT_0 && SPI_DW_CS_GPIO
	default 0

config  SPI_DW_PORT_1_DRV_NAME
	string
	prompt "Designware SPI port 1 device name"
	depends on SPI_DW_PORT_1
	default "spi_dw_1"

config  SPI_DW_PORT_1_REGS
	hex
	prompt "Port 1 registers address"
	depends on SPI_DW_PORT_1
	default 0x00000000

config  SPI_DW_PORT_1_IRQ
	int
	prompt "Port 1 interrupt"
	depends on SPI_DW_PORT_1
	default 0

config  SPI_DW_PORT_1_PRI
	int
	prompt "Port 0 interrupt priority"
	depends on SPI_DW_PORT_1
	default 2

config	SPI_QMSI
	bool "QMSI driver for SPI controller"
	depends on SPI && QMSI_DRIVERS
	default n
	help
	  SPI driver implementation using QMSI library. QMSI is the
	  Quark Microcontroller Software Interface, providing a common
	  interface to the Quark family of microcontrollers.

config SPI_QMSI_INIT_PRIORITY
	int
	prompt "QMSI driver init priority"
	depends on SPI_QMSI
	default 60
	help
	  Device driver initialization priority.

config	SPI_QMSI_PORT_0
	bool
	prompt "QMSI SPI port 0"
	depends on SPI_QMSI
	default n
	help
	  Enable QMSI's SPI controller port 0.

config SPI_QMSI_CS_GPIO
	bool "SPI port CS pin is controlled via a GPIO port"
	depends on SPI_QMSI && GPIO
	default n

config  SPI_QMSI_PORT_0_DRV_NAME
	string
	prompt "QMSI SPI port 0 device name"
	depends on SPI_QMSI_PORT_0
	default "spi_0"

config  SPI_QMSI_PORT_0_IRQ
	int
	prompt "Port 0 interrupt"
	depends on SPI_QMSI_PORT_0
	default 0

config  SPI_QMSI_PORT_0_PRI
	int
	prompt "Port 0 interrupt priority"
	depends on SPI_QMSI_PORT_0
	default 2

config  SPI_QMSI_PORT_0_CS_GPIO_PORT
	string
	prompt "The GPIO port which is used to control CS"
	depends on SPI_QMSI_PORT_0 && SPI_QMSI_CS_GPIO
	default GPIO_QMSI_0_NAME

config  SPI_QMSI_PORT_0_CS_GPIO_PIN
	int "The GPIO PIN which is used to act as a CS pin"
	depends on SPI_QMSI_PORT_0 && SPI_QMSI_CS_GPIO
	default 0

config  SPI_QMSI_PORT_1
	bool
	prompt "QMSI SPI port 1"
	depends on SPI_QMSI
	default n
	help
	  Enable QMSI's SPI controller port 1.

config  SPI_QMSI_PORT_1_DRV_NAME
	string
	prompt "QMSI SPI port 1 device name"
	depends on SPI_QMSI_PORT_1
	default "spi_1"

config  SPI_QMSI_PORT_1_IRQ
	int
	prompt "Port 1 interrupt"
	depends on SPI_QMSI_PORT_1
	default 0

config  SPI_QMSI_PORT_1_PRI
	int
	prompt "Port 0 interrupt priority"
	depends on SPI_QMSI_PORT_1
	default 2

config  SPI_QMSI_PORT_1_CS_GPIO_PORT
	string
	prompt "The GPIO port which is used to control CS"
	depends on SPI_QMSI_PORT_1 && SPI_QMSI_CS_GPIO
	default GPIO_QMSI_0_NAME

config  SPI_QMSI_PORT_1_CS_GPIO_PIN
	int "The GPIO PIN which is used to act as a CS pin"
	depends on SPI_QMSI_PORT_1 && SPI_QMSI_CS_GPIO
	default 0

endif