.. _rpi_pico:

Raspberry Pi Pico
#################

Overview
********

The Raspberry Pi Pico is a small, low-cost, versatile board from
Raspberry Pi. It is equipped with an RP2040 SoC, an on-board LED,
a USB connector, and an SWD interface. The USB bootloader allows it
to be flashed without any adapter, in a drag-and-drop manner.
It is also possible to flash and debug the Pico with its SWD interface,
using an external adapter.

Hardware
********
- Dual core Arm Cortex-M0+ processor running up to 133MHz
- 264KB on-chip SRAM
- 2MB on-board QSPI flash with XIP capabilities
- 26 GPIO pins
- 3 Analog inputs
- 2 UART peripherals
- 2 SPI controllers
- 2 I2C controllers
- 16 PWM channels
- USB 1.1 controller (host/device)
- 8 Programmable I/O (PIO) for custom peripherals
- On-board LED
- 1 Watchdog timer peripheral


.. figure:: img/rpi_pico.jpg
     :align: center
     :alt: Raspberry Pi Pico

     Raspberry Pi Pico (Image courtesy of Raspberry Pi)

Supported Features
==================

The rpi_pico board configuration supports the following
hardware features:

.. list-table::
   :header-rows: 1

   * - Peripheral
     - Kconfig option
     - Devicetree compatible
   * - NVIC
     - N/A
     - :dtcompatible:`arm,v6m-nvic`
   * - UART
     - :kconfig:option:`CONFIG_SERIAL`
     - :dtcompatible:`rpi,pico-uart`
   * - GPIO
     - :kconfig:option:`CONFIG_GPIO`
     - :dtcompatible:`rpi,pico-gpio`
   * - ADC
     - :kconfig:option:`CONFIG_ADC`
     - :dtcompatible:`raspberrypi,pico-adc`
   * - I2C
     - :kconfig:option:`CONFIG_I2C`
     - :dtcompatible:`snps,designware-i2c`
   * - SPI
     - :kconfig:option:`CONFIG_SPI`
     - :dtcompatible:`raspberrypi,pico-spi`
   * - USB Device
     - :kconfig:option:`CONFIG_USB_DEVICE_STACK`
     - :dtcompatible:`raspberrypi,pico-usbd`
   * - HWINFO
     - :kconfig:option:`CONFIG_HWINFO`
     - N/A
   * - Watchdog Timer (WDT)
     - :kconfig:option:`CONFIG_WATCHDOG`
     - :dtcompatible:`raspberrypi,pico-watchdog`
   * - PWM
     - :kconfig:option:`CONFIG_PWM`
     - :dtcompatible:`raspberrypi,pico-pwm`

Programming and Debugging
*************************

Flashing
========

Using SEGGER JLink
------------------

You can Flash the rpi_pico with a SEGGER JLink debug probe as described in
:ref:`Building, Flashing and Debugging <west-flashing>`.

Here is an example of building and flashing the :ref:`blinky-sample` application.

.. zephyr-app-commands::
   :zephyr-app: samples/basic/blinky
   :board: rpi_pico
   :goals: build

.. code-block:: bash

  west flash --runner jlink

Using OpenOCD
-------------

To use PicoProbe, You must configure **udev**.

Create a file in /etc/udev.rules.d with any name, and write the line below.

.. code-block:: bash

   ATTRS{idVendor}=="2e8a", ATTRS{idProduct}=="0004", MODE="660", GROUP="plugdev", TAG+="uaccess"

This example is valid for the case that the user joins to `plugdev` groups.

The Raspberry Pi Pico has an SWD interface that can be used to program
and debug the on board RP2040. This interface can be utilized by OpenOCD.
However, to use it with the RP2040, `fork of OpenOCD supporting RP2040`_ is needed.

If you are using Debian based system (including RaspberryPi OS, Ubuntu. and more),
using `pico_setup.sh`_ script is convenient to set up forked version of OpenOCD.

Depending on the interface used (such as JLink), you might need to
checkout to a branch that supports this interface, before proceeding.
Build and install OpenOCD as described in the README.

Here is an example of building and flashing the :ref:`blinky-sample` application.

.. zephyr-app-commands::
   :zephyr-app: samples/basic/blinky
   :board: rpi_pico
   :goals: build flash
   :gen-args: -DOPENOCD=/usr/local/bin/openocd -DOPENOCD_DEFAULT_PATH=/usr/local/share/openocd/scripts -DRPI_PICO_DEBUG_ADAPTER=picoprobe

Set `/usr/local/bin/openocd` to **OPENOCD** and `/usr/local/share/openocd/scripts` to **OPENOCD_DEFAULT_PATH** will works
with OpenOCD that install with default configuration.
This configuration also works with an environment that is set up by `pico_setup.sh`_ script.

**RPI_PICO_DEBUG_ADAPTER** specifies what debug adapter is used for debugging.

If **RPI_PICO_DEBUG_ADAPTER** was not assigned, use `picoprobe` as default. And also able to use `raspberrypi-swd`.
How to connect `picoprobe` and `raspberrypi-swd` is described in `Getting Started with Raspberry Pi Pico`_.
Any other SWD debug adapter maybe also work with this configuration.

**RPI_PICO_DEBUG_ADAPTER** value remember into CMakeCache.txt.
So you can omit the option in `west flash` and `west debug` execution,
you need only the `west build` case.

**RPI_PICO_DEBUG_ADAPTER** is used in an argument to OpenOCD as `"source [find interface/${RPI_PICO_DEBUG_ADAPTER}.cfg]"`.
Thus, **RPI_PICO_DEBUG_ADAPTER** needs to assign from the definition file name of debugging adapter.

You can also flash the board with the following
command that directly call OpenOCD (assuming a SEGGER JLink adapter is used):

.. code-block:: console

   $ openocd -f interface/jlink.cfg -c 'transport select swd' -f target/rp2040.cfg -c "adapter speed 2000" -c 'targets rp2040.core0' -c 'program path/to/zephyr.elf verify reset exit'

Using UF2
---------

If you don't have an SWD adapter, you can flash the Raspberry Pi Pico with
a UF2 file. By default, building an app for this board will generate a
`build/zephyr/zephyr.uf2` file. If the Pico is powered on with the `BOOTSEL`
button pressed, it will appear on the host as a mass storage device. The
UF2 file should be drag-and-dropped to the device, which will flash the Pico.

Debugging
=========

The SWD interface can also be used to debug the board. To achieve this, you can
either user SEGGER JLink or OpenOCD.

Using SEGGER JLink
------------------

Use a SEGGER JLink debug probe and follow the instruction in
:ref:`Building, Flashing and Debugging<west-debugging>`.


Using OpenOCD
-------------

Install OpenOCD as described for flashing the board.

.. note::
  `fork of OpenOCD supporting RP2040`_ does not provide ZephyrRTOS enhancement.
  (No RTOS awareness. Thus, can't recognize threads.)

Here is an example for debugging the :ref:`blinky-sample` application.

.. zephyr-app-commands::
   :zephyr-app: samples/basic/blinky
   :board: rpi_pico
   :maybe-skip-config:
   :goals: debug
   :gen-args: -DOPENOCD=/usr/local/bin/openocd -DOPENOCD_DEFAULT_PATH=/usr/local/share/openocd/scripts -DRPI_PICO_DEBUG_ADAPTER=raspberrypi-swd

As with flashing, you can specify the debug adapter by specifying **RPI_PICO_DEBUG_ADAPTER**
at `west build` time. No needs to specify it at `west debug` time.

You can also debugging with OpenOCD and gdb launching from command-line.
Run the following command:

.. code-block:: console

   $ openocd -f interface/jlink.cfg -c 'transport select swd' -f target/rp2040.cfg -c "adapter speed 2000" -c 'targets rp2040.core0'

On another terminal, run:

.. code-block:: console

   $ gdb-multiarch

Inside gdb, run:

.. code-block:: console

   (gdb) tar ext :3333
   (gdb) file path/to/zephyr.elf

You can then start debugging the board.

.. target-notes::

.. _fork of OpenOCD supporting RP2040:
   https://github.com/raspberrypi/openocd

.. _pico_setup.sh:
   https://raw.githubusercontent.com/raspberrypi/pico-setup/master/pico_setup.sh

.. _Getting Started with Raspberry Pi Pico:
  https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf