/*
 * Copyright (c) 2017-2020 NXP
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <zephyr/kernel.h>
#include <zephyr/device.h>
#include <zephyr/init.h>
#include <soc.h>
#include <zephyr/linker/sections.h>
#include <zephyr/linker/linker-defs.h>
#include <fsl_clock.h>
#include <zephyr/arch/cpu.h>
#include <zephyr/arch/arm/aarch32/cortex_m/cmsis.h>
#ifdef CONFIG_NXP_IMX_RT_BOOT_HEADER
#include <fsl_flexspi_nor_boot.h>
#endif
#include <zephyr/dt-bindings/clock/imx_ccm.h>
#include <fsl_iomuxc.h>
#if CONFIG_USB_DC_NXP_EHCI
#include "usb_phy.h"
#include "usb.h"
#endif

#define CCM_NODE	DT_INST(0, nxp_imx_ccm)

#define BUILD_ASSERT_PODF_IN_RANGE(podf, a, b)				\
	BUILD_ASSERT(DT_PROP(DT_CHILD(CCM_NODE, podf), clock_div) >= (a) && \
		     DT_PROP(DT_CHILD(CCM_NODE, podf), clock_div) <= (b), \
		     #podf " is out of supported range (" #a ", " #b ")")

#ifdef CONFIG_INIT_ARM_PLL
/* ARM PLL configuration for RUN mode */
const clock_arm_pll_config_t armPllConfig = {
	.loopDivider = 100U
};
#endif

#if CONFIG_USB_DC_NXP_EHCI
/* USB PHY condfiguration */
#define BOARD_USB_PHY_D_CAL (0x0CU)
#define BOARD_USB_PHY_TXCAL45DP (0x06U)
#define BOARD_USB_PHY_TXCAL45DM (0x06U)
#endif

#ifdef CONFIG_INIT_ENET_PLL
/* ENET PLL configuration for RUN mode */
const clock_enet_pll_config_t ethPllConfig = {
#if defined(CONFIG_SOC_MIMXRT1011) || \
	defined(CONFIG_SOC_MIMXRT1015) || \
	defined(CONFIG_SOC_MIMXRT1021) || \
	defined(CONFIG_SOC_MIMXRT1024)
	.enableClkOutput500M = true,
#endif
#ifdef CONFIG_ETH_MCUX
	.enableClkOutput = true,
#endif
#if defined(CONFIG_PTP_CLOCK_MCUX)
	.enableClkOutput25M = true,
#else
	.enableClkOutput25M = false,
#endif
	.loopDivider = 1,
};
#endif

#if CONFIG_USB_DC_NXP_EHCI
	usb_phy_config_struct_t usbPhyConfig = {
		BOARD_USB_PHY_D_CAL, BOARD_USB_PHY_TXCAL45DP, BOARD_USB_PHY_TXCAL45DM,
	};
#endif

#ifdef CONFIG_INIT_VIDEO_PLL
const clock_video_pll_config_t videoPllConfig = {
	.loopDivider = 31,
	.postDivider = 8,
	.numerator = 0,
	.denominator = 0,
};
#endif

#ifdef CONFIG_NXP_IMX_RT_BOOT_HEADER
const __imx_boot_data_section BOOT_DATA_T boot_data = {
	.start = CONFIG_FLASH_BASE_ADDRESS,
	.size = KB(CONFIG_FLASH_SIZE),
	.plugin = PLUGIN_FLAG,
	.placeholder = 0xFFFFFFFF,
};

const __imx_boot_ivt_section ivt image_vector_table = {
	.hdr = IVT_HEADER,
	.entry = (uint32_t) _vector_start,
	.reserved1 = IVT_RSVD,
#ifdef CONFIG_DEVICE_CONFIGURATION_DATA
	.dcd = (uint32_t) dcd_data,
#else
	.dcd = (uint32_t) NULL,
#endif
	.boot_data = (uint32_t) &boot_data,
	.self = (uint32_t) &image_vector_table,
	.csf = (uint32_t)CSF_ADDRESS,
	.reserved2 = IVT_RSVD,
};
#endif

/**
 * @brief Initialize the system clock
 */
static ALWAYS_INLINE void clock_init(void)
{
	/* Boot ROM did initialize the XTAL, here we only sets external XTAL
	 * OSC freq
	 */
	CLOCK_SetXtalFreq(DT_PROP(DT_CLOCKS_CTLR_BY_NAME(CCM_NODE, xtal),
				  clock_frequency));
	CLOCK_SetRtcXtalFreq(DT_PROP(DT_CLOCKS_CTLR_BY_NAME(CCM_NODE, rtc_xtal),
				     clock_frequency));

	/* Set PERIPH_CLK2 MUX to OSC */
	CLOCK_SetMux(kCLOCK_PeriphClk2Mux, 0x1);

	/* Set PERIPH_CLK MUX to PERIPH_CLK2 */
	CLOCK_SetMux(kCLOCK_PeriphMux, 0x1);

	/* Setting the VDD_SOC value.
	 */
	DCDC->REG3 = (DCDC->REG3 & (~DCDC_REG3_TRG_MASK)) | DCDC_REG3_TRG(CONFIG_DCDC_VALUE);
	/* Waiting for DCDC_STS_DC_OK bit is asserted */
	while (DCDC_REG0_STS_DC_OK_MASK !=
			(DCDC_REG0_STS_DC_OK_MASK & DCDC->REG0)) {
		;
	}

#ifdef CONFIG_INIT_ARM_PLL
	CLOCK_InitArmPll(&armPllConfig); /* Configure ARM PLL to 1200M */
#endif
#ifdef CONFIG_INIT_ENET_PLL
	CLOCK_InitEnetPll(&ethPllConfig);
#endif
#ifdef CONFIG_INIT_VIDEO_PLL
	CLOCK_InitVideoPll(&videoPllConfig);
#endif

#if DT_NODE_EXISTS(DT_CHILD(CCM_NODE, arm_podf))
	/* Set ARM PODF */
	BUILD_ASSERT_PODF_IN_RANGE(arm_podf, 1, 8);
	CLOCK_SetDiv(kCLOCK_ArmDiv, DT_PROP(DT_CHILD(CCM_NODE, arm_podf), clock_div) - 1);
#endif
	/* Set AHB PODF */
	BUILD_ASSERT_PODF_IN_RANGE(ahb_podf, 1, 8);
	CLOCK_SetDiv(kCLOCK_AhbDiv, DT_PROP(DT_CHILD(CCM_NODE, ahb_podf), clock_div) - 1);
	/* Set IPG PODF */
	BUILD_ASSERT_PODF_IN_RANGE(ipg_podf, 1, 4);
	CLOCK_SetDiv(kCLOCK_IpgDiv, DT_PROP(DT_CHILD(CCM_NODE, ipg_podf), clock_div) - 1);

	/* Set PRE_PERIPH_CLK to PLL1, 1200M */
	CLOCK_SetMux(kCLOCK_PrePeriphMux, 0x3);

	/* Set PERIPH_CLK MUX to PRE_PERIPH_CLK */
	CLOCK_SetMux(kCLOCK_PeriphMux, 0x0);

#ifdef CONFIG_UART_MCUX_LPUART
	/* Configure UART divider to default */
	CLOCK_SetMux(kCLOCK_UartMux, 0); /* Set UART source to PLL3 80M */
	CLOCK_SetDiv(kCLOCK_UartDiv, 0); /* Set UART divider to 1 */
#endif

#ifdef CONFIG_I2C_MCUX_LPI2C
	CLOCK_SetMux(kCLOCK_Lpi2cMux, 0); /* Set I2C source as USB1 PLL 480M */
	CLOCK_SetDiv(kCLOCK_Lpi2cDiv, 5); /* Set I2C divider to 6 */
#endif

#ifdef CONFIG_SPI_MCUX_LPSPI
	CLOCK_SetMux(kCLOCK_LpspiMux, 1); /* Set SPI source to USB1 PFD0 720M */
	CLOCK_SetDiv(kCLOCK_LpspiDiv, 7); /* Set SPI divider to 8 */
#endif

#ifdef CONFIG_DISPLAY_MCUX_ELCDIF
	CLOCK_SetMux(kCLOCK_LcdifPreMux, 2);
	CLOCK_SetDiv(kCLOCK_LcdifPreDiv, 4);
	CLOCK_SetDiv(kCLOCK_LcdifDiv, 1);
#endif


#if DT_NODE_HAS_STATUS(DT_NODELABEL(enet), okay) && CONFIG_NET_L2_ETHERNET
	/* Enable clock output for ENET1 */
	IOMUXC_EnableMode(IOMUXC_GPR, kIOMUXC_GPR_ENET1TxClkOutputDir, true);
#endif

#if DT_NODE_HAS_STATUS(DT_NODELABEL(usb1), okay) && CONFIG_USB_DC_NXP_EHCI
	CLOCK_EnableUsbhs0PhyPllClock(kCLOCK_Usb480M,
		DT_PROP_BY_PHANDLE(DT_NODELABEL(usb1), clocks, clock_frequency));
	CLOCK_EnableUsbhs0Clock(kCLOCK_Usb480M,
		DT_PROP_BY_PHANDLE(DT_NODELABEL(usb1), clocks, clock_frequency));
	USB_EhciPhyInit(kUSB_ControllerEhci0, CPU_XTAL_CLK_HZ, &usbPhyConfig);
#endif

#if DT_NODE_HAS_STATUS(DT_NODELABEL(usb2), okay) && CONFIG_USB_DC_NXP_EHCI
	CLOCK_EnableUsbhs1PhyPllClock(kCLOCK_Usb480M,
		DT_PROP_BY_PHANDLE(DT_NODELABEL(usb2), clocks, clock_frequency));
	CLOCK_EnableUsbhs1Clock(kCLOCK_Usb480M,
		DT_PROP_BY_PHANDLE(DT_NODELABEL(usb2), clocks, clock_frequency));
	USB_EhciPhyInit(kUSB_ControllerEhci1, CPU_XTAL_CLK_HZ, &usbPhyConfig);
#endif

#if DT_NODE_HAS_STATUS(DT_NODELABEL(usdhc1), okay) && CONFIG_IMX_USDHC
	/* Configure USDHC clock source and divider */
	CLOCK_InitSysPfd(kCLOCK_Pfd0, 24U);
	CLOCK_SetDiv(kCLOCK_Usdhc1Div, 1U);
	CLOCK_SetMux(kCLOCK_Usdhc1Mux, 1U);
	CLOCK_EnableClock(kCLOCK_Usdhc1);
#endif
#if DT_NODE_HAS_STATUS(DT_NODELABEL(usdhc2), okay) && CONFIG_IMX_USDHC
	/* Configure USDHC clock source and divider */
	CLOCK_InitSysPfd(kCLOCK_Pfd0, 24U);
	CLOCK_SetDiv(kCLOCK_Usdhc2Div, 1U);
	CLOCK_SetMux(kCLOCK_Usdhc2Mux, 1U);
	CLOCK_EnableClock(kCLOCK_Usdhc2);
#endif

#ifdef CONFIG_VIDEO_MCUX_CSI
	CLOCK_EnableClock(kCLOCK_Csi); /* Disable CSI clock gate */
	CLOCK_SetDiv(kCLOCK_CsiDiv, 0); /* Set CSI divider to 1 */
	CLOCK_SetMux(kCLOCK_CsiMux, 0); /* Set CSI source to OSC 24M */
#endif
#ifdef CONFIG_CAN_MCUX_FLEXCAN
	CLOCK_SetDiv(kCLOCK_CanDiv, 1); /* Set CAN_CLK_PODF. */
	CLOCK_SetMux(kCLOCK_CanMux, 2); /* Set Can clock source. */
#endif

#ifdef CONFIG_LOG_BACKEND_SWO
	/* Enable ARM trace clock to enable SWO output */
	CLOCK_EnableClock(kCLOCK_Trace);
	/* Divide root clock output by 3 */
	CLOCK_SetDiv(kCLOCK_TraceDiv, 3);
	/* Source clock from 528MHz system PLL */
	CLOCK_SetMux(kCLOCK_TraceMux, 0);
#endif

	/* Keep the system clock running so SYSTICK can wake up the system from
	 * wfi.
	 */
	CLOCK_SetMode(kCLOCK_ModeRun);

}

#if CONFIG_I2S_MCUX_SAI
void imxrt_audio_codec_pll_init(uint32_t clock_name, uint32_t clk_src,
					uint32_t clk_pre_div, uint32_t clk_src_div)
{
	switch (clock_name) {
	case IMX_CCM_SAI1_CLK:
		CLOCK_SetMux(kCLOCK_Sai1Mux, clk_src);
		CLOCK_SetDiv(kCLOCK_Sai1PreDiv, clk_pre_div);
		CLOCK_SetDiv(kCLOCK_Sai1Div, clk_src_div);
		break;
	case IMX_CCM_SAI2_CLK:
		CLOCK_SetMux(kCLOCK_Sai2Mux, clk_src);
		CLOCK_SetDiv(kCLOCK_Sai2PreDiv, clk_pre_div);
		CLOCK_SetDiv(kCLOCK_Sai2Div, clk_src_div);
		break;
	case IMX_CCM_SAI3_CLK:
		CLOCK_SetMux(kCLOCK_Sai2Mux, clk_src);
		CLOCK_SetDiv(kCLOCK_Sai2PreDiv, clk_pre_div);
		CLOCK_SetDiv(kCLOCK_Sai2Div, clk_src_div);
		break;
	default:
		return;
	}
}
#endif

/**
 *
 * @brief Perform basic hardware initialization
 *
 * Initialize the interrupt controller device drivers.
 * Also initialize the timer device driver, if required.
 *
 * @return 0
 */

static int imxrt_init(const struct device *arg)
{
	ARG_UNUSED(arg);

	unsigned int oldLevel; /* old interrupt lock level */

	/* disable interrupts */
	oldLevel = irq_lock();

	if ((SCB->CCR & SCB_CCR_DC_Msk) == 0) {
		SCB_EnableDCache();
	}

	/* Initialize system clock */
	clock_init();

	/*
	 * install default handler that simply resets the CPU
	 * if configured in the kernel, NOP otherwise
	 */
	NMI_INIT();

	/* restore interrupt state */
	irq_unlock(oldLevel);
	return 0;
}

#ifdef CONFIG_PLATFORM_SPECIFIC_INIT
void z_arm_platform_init(void)
{
#if (DT_DEP_ORD(DT_NODELABEL(ocram)) != DT_DEP_ORD(DT_CHOSEN(zephyr_sram))) && \
	CONFIG_OCRAM_NOCACHE
	/* Copy data from flash to OCRAM */
	memcpy(&__ocram_data_start, &__ocram_data_load_start,
		(&__ocram_data_end - &__ocram_data_start));
	/* Zero BSS region */
	memset(&__ocram_bss_start, 0, (&__ocram_bss_end - &__ocram_bss_start));
#endif
	/* Call CMSIS SystemInit */
	SystemInit();
}
#endif

SYS_INIT(imxrt_init, PRE_KERNEL_1, 0);